Unbranded DAC145EB6WDB6 Le manuel du propriétaire

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

MANUAL DEL PROPIETARIO

www.Danby.com

*

2021.03.08

MODEL • MODÈLE • MODELO

DAC145EB6WDB-6

AIR CONDITIONER

Owner’s Manual.............................1 - 24

CLIMATISEUR

Manual du propriétaire.................25 - 48

AIRE ACONDICIONADO

Manual del propietario..................50 - 74

1

Welcome to the Danby family.

We are proud of our quality products and we believe in dependable service. We suggest

that you read this owner’s manual before plugging in your new appliance as it contains

important operation information, safety information, troubleshooting, and maintenance tips

to ensure the reliability and longevity of your appliance.

You are entitled to the warranty coverage as described in the owner’s manual provided with

your new appliance.

1. Please write down your appliance information below. You must keep the original proof

of purchase receipt to validate and receive warranty services.

2. Register your product online and receive a FREE 2 MONTH WARRANTY EXTENSION

after ﬁ lling out a product survey, at www.danby.com/support/product-registration/

Need Help?

1. Read your Owner’s Manual for installation help, troubleshooting, and maintenance

assistance.

2. Visit www.Danby.com to access self-service tools, FAQs and much more by searching

your model number in the search bar.

3. For the Quickest Customer Service, please ﬁ ll out the web form at www.danby.com/

support. Your submission will go directly to an expert on your particular appliance.

Our average response times are between 20 minutes and 2 hours, during EST business

hours.

4. Call 1-800-263-2629 - please note that during peak hours, hold times can exceed one

hour.

Model Number: ____________________________________________________

Serial Number: ____________________________________________________

Date of Purchase: __________________________________________________

SAVE THESE INSTRUCTIONS!

CAUTION: RISK OF FIRE

Flammable refrigerant used. When maintaining

or disposing of the air conditioner, the refrigerant

must not be allowed to vent into the open air.

WARNING Shows that the appliance uses a ﬂ ammable refrigerant. If the

refrigerant leaks and is exposed to an external ignition source, there is

a risk of ﬁ re.

CAUTION Shows that the operation manual should be read carefully.

CAUTION Shows that service personnel should be handling this equipment with

reference to the installation manual.

CAUTION Shows that the information is available such as the operating manual

or the installation manual.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

SAFETY PRECAUTIONS

WARNING

• Installation must be performed according to the installation instructions. Improper installation can cause

water leakage, electrical shock or ﬁ re.

• Use only the included accessories and parts and speciﬁ ed tools for the installation. Using non-standard

parts can cause water leakage, electrical shock, ﬁ re and injury or property damage.

• Make sure that the outlet you are using is grounded and has the appropriate voltage. The power cord

is equipped with a three-prong grounding plug to protect against shock. Voltage information can be

found on the nameplate of the unit.

• You unit must be used in a properly grounded wall receptacle. if the wall receptacle you intend to use is

not adequately grounded or protected by a time delay fuse or circuit breaker (the fuse of circuit breaker

needed is determined by the maximum current of the unit. The maximum current is indicated on the

nameplate located on the unit), have a qualiﬁ ed electrician install the proper receptacle.

• Install the unit on a ﬂ at, sturdy surface. Failure to do so could result in damage or excessive noise and

vibration.

• The unit must be kept free from obstruction to ensure proper function and to mitigate safety hazards.

• Do not modify the length of the power cord or use an extension cord to power the unit.

• Do not share a single outlet with other electrical appliances. Improper power supply can cause ﬁ re or

electrical shock.

• Do not install you air conditioner in a wet room such as a bathroom or laundry room. Too much

exposure to water can cause electrical components to short circuit.

• Do not install the unit in a location that may be exposed to combustible fas as this could cause ﬁ re.

• The unit has wheels to facilitate moving. Make sure not to use the wheels on thick carpet or to roll over

objects as this could cause tipping.

• Do not operate a unit that been dropped or damaged.

• The appliance with the electric heater shall have at least 1 meter space from combustible materials.

• Do not touch the unit with wet or damp hands or when barefoot.

• If the air conditioner is knocked over during use, turn off the unit and unplug it from the main power

supply immediately. Visually inspect the unit to ensure there is no damage. If you suspect the unit has

been damaged contact a technician or customer service for assistance.

• In a thunderstorm, the power must be cut off to avoid damage to the machine due to lightning.

• You air conditioner should be used in such a way that it is protected from moisture. e.g. condensation,

splashed water, etc. Do not place or store you air conditioner where it can fall or be pulled into water

or any other liquid. Unplug immediately if this occurs.

• All wiring must be performed strictly in accordance with the wiring diagram location inside the unit.

• The units circuit board (PCB) is designed with a fuse to provide over current protection. The

speciﬁ cations of the fuse are printed on the circuit board.

• When the water drainage function is not in use keep the upper and lower drain plugs ﬁ rmly installed in

the unit. The drain plugs can be a choking hazard to children.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

CAUTION

• This appliance is not intended for use by persons (including children) whose physical, sensory or

mental capabilities may be different or reduced, or who lack experience or knowledge, unless such

persons receive supervision or training to operate the appliance by a person responsible for their

safety. Children should be supervised to ensure that they do not play with the appliance. Children must

be supervised around the unit at all times.

• If the power supply cord is damaged it must be replaced by the manufacturer, its service agent or

similarly qualiﬁ ed persons in order to avoid a hazard.

• Prior to cleaning or other maintenance, the appliance must be disconnected from the power supply.

• Do not remove any ﬁ xed covers. Never use this appliance if it is not working properly or if it has been

dropped or damaged.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners or similar coverings. Do

not route cord under furniture or appliances. Arrange cords away from trafﬁ c and where it will not be

tripped over.

• Do not operate a unit with a damaged power cord, plug, power fuse or circuit breaker. Discard the unit

or return to an authorized service facility for examination and/or repair.

• To reduce the risk of ﬁ re or electric shock do not use this air conditioner with any solid-state speed

control device.

• The appliance shall be installed in accordance with national wiring regulations.

• Contact the authorized service technician for repair or maintenance of this unit.

• Contact the authorized service installer for installation of this unit.

• Do not cover or obstruct the inlet or outlet grilles.

• Do not use this product for functions other than those described in this instruction manual.

• Before cleaning turn off the power and unplug the unit.

• Disconnect the power if strange sounds, smells or smoke comes from it.

• Do not press the buttons on the control panel with anything other than your ﬁ ngers.

• Do not remove any ﬁ xed covers. Never use this appliance if it is not working properly or if it has been

dropped or damaged.

• Do not operate or stop the unit by inserting or pulling out the power cord plug.

• Do not use hazardous chemicals to clean or come into contact with the unit. Do not use the unit in the

presence of inﬂ ammable substances or vapour such as alcohol, insecticides, petrol, etc.

• Always transport your air conditioner in a vertical position and stand on a stable, level surface during

use.

• Always contact a qualiﬁ ed person to carry out repairs. If the damaged power supply cord must be

replaced with a new power supply cord obtained from the product manufacturer and not repaired.

• Hold the plug by the head of the power plug when removing it.

• Turn off the appliance when not in use.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Note about ﬂ uorinated gasses

• Fluorinated greenhouse gases are contained in hermetically sealed equipment. For speciﬁ c information

on the type, the amount and the C02 equivalent in tonnes of the ﬂ uorinated greenhouse gas on some

models. Please refer to the relevant label on the unit itself.

• Installation, service, maintenance and repair of this unit must be performed by a certiﬁ ed technician.

• Product installation and recycling must be performed by a certiﬁ ed technician.

WARNING for using R32 refrigerant

• Do not use means to accelerate the defrosting process or to clean other than those recommended by the

manufacturer.

• The appliance shall be stored in a room without continuously operating ignition sources for example,

open ﬂ ames, an operating gas appliance or an operating electric heater.

• Do not pierce or burn.

• Be aware that the refrigerants may not contain an odour.

• The appliance should be installed, operated and stored in a room with a ﬂ oor area according to the

amount of refrigerant to be charged. For speciﬁ c information on the type of gas and the amount,

please refer to the relevant label on the unit itself. When there are differences between the label and the

manual on the minimum room area description, the description on the label shall prevail.

• Compliance with national gas regulations shall be observed.

• Keep ventilation openings clear of obstruction.

• The appliance shall be stored so as to prevent mechanical damage from occurring.

• A warning that the appliance shall be stored in a well-ventilated area where the room size corresponds

to the room area as speciﬁ ed for operation.

• Any person involved with working on the refrigerant circuit should hold a current, valid certiﬁ cate from

an industry accredited assessment authority which authorizes their competence to handle refrigerants

safely in accordance with an industry recognized assessment speciﬁ cation.

• Servicing shall only be performed as recommended by the manufacturer. Maintenance and repair

requiring the assistance of other skilled personnel shall be carried out under the supervision of the

person competent in the use of ﬂ ammable refrigerants.

• Please follow the instruction carefully to handle, install, clear and service the air conditioner to

avoid any damage or hazard. Flammable refrigerant R32 is used within this air conditioner. When

maintaining or disposing of the air conditioner the refrigerant must be recovered properly and should

not be allowed to discharge to the air directly.

• No open ﬁ re or device like switch which may generate spark/arcing shall be around air conditioner to

avoid causing ignition of the ﬂ ammable refrigerant used.

• Please follow the instruction carefully to store or maintain the air conditioner to prevent mechanical

damage from occurring.

• Flammable refrigerant -R32 is used in air conditioner. Please follow the instruction carefully to avoid

any hazard. For speciﬁ c information on the type of gas and the amount, please to the relevant label on

the unit itself.

• The appliance shall be stored in a room without continuously operating open ﬂ ames (for example an

operating gas appliance) and ignition sources (for example an operating electric heater).

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Transport of equipment containing ﬂ ammable refrigerants

See transport regulations.

Marking of equipment using signs

See local regulations.

Disposal of equipment using ﬂ ammable refrigerants

See national regulations.

Storage of equipment / appliances

The storage of equipment should be in accordance with the manufacturer’s instructions.

Storage of packed (unsold) equipment

Storage package protection should be constructed such that the mechanical damage to the equipment

inside the package will not cause a leak of the refrigerant charge. The maximum number of pieces of

equipment permitted to be stored together will be determined by local regulations.

Information on servicing

1. Checks to the area: Prior to beginning work on systems containing ﬂ ammable refrigerants, safety

checks are necessary to ensure that the risk of ignition is minimized. For repair to the refrigerating

system, the following precautions shall be complied with prior to conducting work on the system.

2. Work procedure: Work shall be undertaken under a controlled procedure so as to minimize the risk of

a ﬂ ammable gas or vapour being present while the work is being performed.

3. General work area: All maintenance staff and others working in the local area shall be instructed on

the nature of work being carried out. Work in conﬁ ned spaces shall be avoided. The area around the

work space shall be sectioned off. Ensure that the conditions within the work area have been made safe

by removing all ﬂ ammable material.

4. Checking for the presence of refrigerant: The area shall be checked with an appropriate refrigerant

detector prior to and during work to ensure the technician is aware of potentially ﬂ ammable

atmospheres. Ensure that the leak detection equipment being used is suitable for use with ﬂ ammable

refrigerants, i.e. non-sparking, adequately sealed and intrinsically safe.

5. Presence of ﬁ re extinguisher: If any hot work is to be conducted on the refrigeration equipment or

any associated parts, appropriate ﬁ re extinguishing equipment shall be available to hand. Have a dry

powder or C0

2

ﬁ re extinguisher adjacent to the work area.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

6. No ignition sources: No person carrying out work in relation to a refrigeration system which involves

exposing any pipe work that contains or has contained ﬂ ammable refrigerant shall use any sources

of ignition in such a manner that it may lead to risk of ﬁ re or explosion. All possible ignition sources

including cigarette smoking, should be kept sufﬁ ciently far away from the site of installation, repairing,

removing and disposal during which ﬂ ammable refrigerant can possibly be released to the surrounding

space. Prior to work taking place, the area around the equipment is to be surveyed to make sure there

are no ﬂ ammable hazards or ignition risks. No smoking signs shall be displayed.

7. Ventilated area: Ensure that the area is in the open or that it is adequately ventilated before breaking

into the system or conducting any hot work. A degree of ventilation shall continue during the period

that the work is carried out. The ventilation should safely disperse any released refrigerant and

preferable expel it externally into the atmosphere.

8. Checks to the refrigeration equipment: Where electrical components are being changed, they shall

be ﬁ t for the purpose and to the correct speciﬁ cation. At all times the manufacturer’s maintenance and

service guidelines shall be followed. If in doubt consult the manufacturer’s technical department for

assistance.

The following checks shall be applied to installations using ﬂ ammable refrigerants:

• The charge size is in accordance with the room size within which the refrigerant containing parts are

installed.

• The ventilation machinery and outlets are operating adequately and are not obstructed.

• If an indirect refrigerating circuit is being used, the secondary circuit shall be checked for the presence

of refrigerant.

• Marking to the equipment continues to be visible and legible. Markings and signs that become illegible

must be corrected.

• Refrigeration pipe or components are installed in a position where they are unlikely to be exposed

to any substance which may corrode refrigerant containing components, unless the components are

constructed of materials which are inherently resistant to being corroded or are suitable protected

against being corroded.

9. Checks to electrical devices: Repair and maintenance to electrical components shall include initial

safety checks and component inspection procedures. If a fault exists that could compromise safety, then

no electrical supply shall be connected to the circuit until it is satisfactorily dealt with. If the fault cannot

be corrected immediately but it is necessary to continue operation, an adequate temporary solution

shall be used. This shall be reported to the owner of the equipment so all parties are advised.

Initial safety checks shall include:

• That capacitors are discharged. This shall be done in a safe manner to avoid possibility of sparking.

• That no live electrical components and wiring are exposed while charging, recovering or purging the

system.

• That there is continuity of earth bonding.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Repairs to sealed components

1. During repairs to sealed components, all electrical supplies shall be disconnected from the equipment

being worked upon prior to any removal of sealed covers, etc. If it is absolutely necessary to have an

electrical supply to equipment during servicing then a permanently operating form of leak detection

shall be located at the most critical point to warn of a potentially hazardous situation.

2. To ensure that by working on electrical components the casing is not altered in such a way that the level

of protection is affected, particular attention shall be paid to the following:

• Damage to cables, excessive number of connections, terminals not made to original speciﬁ cation,

damage to seals, incorrect ﬁ tting of glands, etc.

• Ensure the apparatus is mounted securely.

• Ensure that seals or sealing materials have not degraded such that they no longer serve the purpose of

preventing the ingress of ﬂ ammable atmospheres. Replacement parts shall be in accordance with the

manufacturer’s speciﬁ cations.

Note: The use of silicon sealant may inhibit the effectiveness of some types of leak detection equipment.

Intrinsically safe components do not have to be isolated prior to working on them.

Repair to intrinsically safe components

Do not apply any permanent inductive or capacitance loads to the circuit without ensuring that this

will not exceed the permissible voltage and current permitted for the equipment in use. Intrinsically

safe components are the only types that can be worked on while live in the presence of a ﬂ ammable

atmosphere. The test apparatus shall be at the correct rating. Replace components only with parts speciﬁ ed

by the manufacturer. Other parts may result in the ignition of refrigerant in the atmosphere from a leak.

Cabling

Check that cabling will not be subject to wear, corrosion, excessive pressure, vibration, sharp edges or any

other adverse environmental effects. The check shall also take into account the effects of aging or continual

vibration from sources such as compressors or fans.

Detection of ﬂ ammable refrigerants

Under no circumstances shall potential sources of ignition be used in the searching for or detection of

refrigerant leaks. A halide torch or any other detector using a naked ﬂ ame shall not be used.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Leak detection methods

The following leak detection methods are deemed acceptable for systems containing ﬂ ammable

refrigerants:

• Electronic leak detectors shall be used to detect ﬂ ammable refrigerants but the sensitivity may not be

adequate or may need recalibration. Detection equipment shall be calibrated in a refrigerant-free area.

Ensure that the detector is not a potential source of ignition and is suitable for the refrigerant used.

• Leak detection equipment shall be set at a percentage of the LFL of the refrigerant and shall be

calibrated to the refrigerant employed and the appropriate percentage of gas (25% maximum) is

conﬁ rmed.

• Leak detection ﬂ uids are suitable for use with most refrigerants but the use of detergents containing

chlorine shall be avoided as the chlorine may react with the refrigerant and corrode the copper or

pipe-work.

• If a leak is suspected, all naked ﬂ ames shall be removed or extinguished.

• If a leakage of refrigerant is found which requires brazing, all of the refrigerant shall be recovered

from the system or isolated by means of shut off valves in a part of the system remote from the leak.

Oxygen free nitrogen (OFN) shall then be purged through the system both before and during the

brazing process.

Removal and evacuation

When breaking into the refrigerant circuit to make repairs or for any other purpose conventional

procedures shall be used. However, it is important that the best practice is followed since ﬂ ammability is a

consideration. The following procedures shall be adhered to:

• Remove refrigerant.

• Purge the circuit with inert gas.

• Evacuate.

• Purge again with inert gas.

• Open the circuit by cutting or brazing.

• The refrigerant charge shall be recovered into the correct recovery cylinders. The system shall be

ﬂ ushed with OFN to render the unit safe. This process may need to be repeated several times.

Compressed air or oxygen shall not be used for this task.

• Flushing shall be achieved by breaking the vacuum in the system with OFN and continuing to ﬁ ll until

the working pressure is achieved, then venting to atmosphere and ﬁ nally pulling down to a vacuum.

This process shall be repeated until no refrigerant is within the system. When the ﬁ nal OFN charge

is used, the system shall be vented down to atmospheric pressure to enable work to take place. This

operation is absolutely vital is brazing operations on the pipe-work are to take place.

• Ensure that the outlet for the vacuum pump is not close to any ignition sources and there is ventilation

available.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Charging procedures

In addition to conventional charging procedures, the following requirements shall be followed:

• Ensure that contamination of different refrigerants does not occur when using charging equipment.

Hoses or lines shall be as short as possible to minimize the amount of refrigerant contained in them.

• Cylinders shall be kept upright.

• Ensure that the refrigeration system is earthed prior to charging the system with refrigerant.

• Label the system when charging is complete, if not already labeled.

• Extreme care shall be taken not to overﬁ ll the refrigeration system.

• Prior to recharging the system it shall be pressure tested with OFN. The system shall be leak tested on

completion of charging but prior to commissioning. A follow up leak test shall be carried out prior to

leaving the site.

Decommissioning

Before carrying out this procedure, it is essential that the technician is completely familiar with the

equipment in all its detail. It is recommended good practice that all refrigerants are recovered safely. Prior

to the task being carried out, an oil and refrigerant sample shall be taken in case analysis is required

prior to re-use of reclaimed refrigerant. It is essential that electrical power is available before the task is

commenced.

A. Become familiar with the equipment and its operation.

B. Isolate system electrically.

C. Before attempting the procedure ensure that:

• Mechanical handling equipment is available if required for handling refrigerant cylinders.

• All personal protective equipment is available and being used correctly.

• The recovery process is supervised at all times by a competent person.

• Recovery equipment and cylinders conform to the appropriate standards.

D. Pump down refrigerant system, if possible.

E. If a vacuum is not possible, make a manifold so that refrigerant can be removed from various parts of

the system.

F. Make sure that cylinder is situated on the scales before recovery takes place.

G. Start the recovery machine and operate in accordance with the manufacturer’s instructions.

H. Do not overﬁ ll cylinders. No more than 80% volume liquid charge.

I. Do not exceed the maximum working pressure of the cylinder, even temporarily.

J. When the cylinders have been ﬁ lled correctly and the process is completed, make sure that the cylinders

and the equipment are removed from the site promptly and all isolation valves on the equipment are

closed off.

K. Recovered refrigerant shall not be charged into another refrigeration system unless it has been cleaned

and checked.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Labeling

Equipment shall be labeled stating that it has been decommissioned and emptied of refrigerant. The label

shall be dated and signed. Ensure that there are labels on the equipment stating the equipment contains

ﬂ ammable refrigerant.

Recovery

When removing refrigerant from a system, either for servicing or decommissioning, it is recommended

good practice that all refrigerants are removed safely.

When transferring refrigerant into cylinders, ensure that only appropriate refrigerant recovers cylinders are

employed. Ensure that the correct number of cylinders for holding the total system charge are available.

All cylinders to be used are designed for the recovered refrigerant and labeled for that refrigerant, i.e.

special cylinders for the recovery of refrigerant. Cylinders shall be complete with pressure relief valve and

associated shut-off valves in good working order. Empty recovery cylinders are evacuated and, if possible,

cooled before recovery occurs.

The recovery equipment shall be in good working order with a set of instructions concerning the equipment

that is at hand and shall be suitable for the recovery of ﬂ ammable refrigerants. In addition, a set of

calibrated weighing scales shall be available and in good working order. Hoses shall be complete with

leak-free disconnect couplings and in good condition. Before using the recovery machine, check that is it

in satisfactory working order, has been properly maintained and that any associated electrical components

are sealed to prevent ignition in the event of a refrigerant leak. Consult the manufacturer if in doubt.

The recovered refrigerant shall be returned to the refrigerant supplier in the correct recovery cylinder

and the relevant waste transfer note shall be arranged. Do not mix refrigerants in recovery units and

especially not in cylinders. If compressors or compressor oils are to be removed, ensure that they have

been evacuated to an acceptable level to make certain that ﬂ ammable refrigerant does not remain within

the lubricant. The evacuation process shall be carried out prior to returning the compressor to the suppliers.

Only electric heating to the compressor body shall be employed to accelerate this process. When oil is

drained form a system, it shall be carried out safely.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

LOCATION

This air conditioner is designed for single or double

hung windows. Since window designs vary, it may

be necessary to make some modiﬁ cations for safe

installation.

This air conditioner is not designed for vertical,

slider type windows or “through the wall”

installation.

Ensure that the window and frame are structurally

sound and free from dry or rotted wood.

Install the air conditioner in a window on a side

of the building which favors more shade than

sunlight. If the appliance must be in direct sunlight,

it is advisable to provide a shade awning over the

appliance to ensure efﬁ cient functioning.

Do not install the appliance where leakage of

combustible gas is suspected.

This appliance is designed to evaporate

condensation under normal conditions. Under

extremely hot or humid conditions, excess

condensation may overﬂ ow to the outside. The

appliance should be installed where condensation

cannot drip on pedestrians or neighboring

properties.

Provide sufﬁ cient clearance around the appliance

to allow ample air circulation. The rear of the

appliance should be outdoors, it should not be in

a garage or another room. Keep the appliance

away from obstacles and at least 76 cm (30 inches)

above the ground. Ensure that curtains and other

obstructions do not block air ﬂ ow to the appliance.

76.2 cm

(30 inches)

50.8 cm

(20 inches)

50.8 cm

(20 inches)

12 cm

(30.5 in)

INSTALLATION INSTRUCTIONS

12

REQUIRED TOOLS

• Screwdrivers: Phillips and ﬂ at head.

• Power Drill: 3.2mm (1/8”) diameter drill bit

• Pencil

• Measuring Tape

• Scissors

• Carpenter’s Level

ACCESSORIES

The following accessories are included with

the appliance and should be used during the

installation.

1. 13 mm (1/2 inch) screws (x7)

2. 9.5 mm (3/8 inch) screws (x4) (Factory installed

on some models.)

3. Safety Lock

4. Adhesive foam seal

5. Regular foam seal

6. “L” shaped mounting bracket (Factory installed

on some models.)

7. Bracket for wood windows (x2)

8. Bracket for vinyl windows (x2)

9. Weather stripping (x5)

10. Side curtains (x2)

1

2 3

4

5

6

9

8

7

10

INSTALLATION INSTRUCTIONS

L BRACKET

The “L” shaped bracket may come factory installed

on some models.

If the “L” shaped bracket is not pre-installed, attach

it to the top of the cabinet as shown below using the

provided 9.5 mm (3/8”) screws (x4).

13

INSTALLATION

Attach the side curtains to the appliance by sliding

the curtain frame into the side channel of the

cabinet. The curtains are labeled “left” and “right

on the frames. This refers to the left and right

sides of the appliance when facing the front of the

appliance.

Cut the regular foam seal to ﬁ t the area of the

window sill that the air conditioner will rest on.

Place the air conditioner into the window with the

“L” shaped mounting bracket positioned in front of

the upper sash. The bottom of the cabinet should be

positioned on the recessed portion of the window

frame. Pull the upper window sash down until it

rests just behind the front ﬂ ange of the “L” shaped

mounting bracket.

Expand the side curtains on each side and secure

the top of the frames to the window sash using one

13 mm (1/2”) screw on each side of the “L” shaped

mounting bracket.

Attach the clamps on the lower part of each curtain

to the window sill using one 13 mm (1/2”) screw on

each side of the cabinet.

Place the adhesive foam seal into the opening

between the inside and outside windows and

attached the safety lock to the outside window frame

using two 13 mm (1/2”) screws.

Check the Tilt Angle

The air conditioner should be tilted downward

towards the outside approximately 3° to 4°. This

tilt will encourage any condensed water to drain

to the outside. If any condensed water leaks to the

inside of the house, check the tilt angle and adjust

as necessary.

Measure the tilt angle from the front of the cabinet’s

edge. The difference in height between the front and

the back of the appliance, labeled “A” on the image

below, should be approximately:

• 2.5 cm - 3.5 cm (1” - 1 3/8”)

A

CONTROL PANEL

1. Remote Control Receiver: Ensure this receiver is not obscured by curtains or other items as it could

impact remote control functioning.

2. Follow Me Indicator Light: Illuminates when the Follow Me function is active. Follow Me can only be set

from the remote control.

3. Power Button: Used to turn the appliance on or off.

4. Mode Button: Used to choose the operating mode.

5. Temperature Control Buttons: Used to adjust the set temperature in 1° increments and the timer function

in 30 minute increments up to 10 hours and then in 1 hour increments up to 24 hours.

6. Display Panel: Displays the set temperature, the ambient temperature and the timer settings. To change

the temperature scale being displayed, press the up and down buttons at the same time.

7. Fan Button: Used to set the fan speed. The fan can be set to Low, Medium, High and Auto.

8. Wireless connect button: Used to connect to a wireless network.

9. Energy Saver Button: Used to set the energy saver function.

10. Filter Button: The indicator light will illuminate as a reminder to check the ﬁ lter. Once the ﬁ lter has been

cleaned, use this button to resume operation.

11. Sleep Button: Used to set the Sleep function.

12. Timer Button: Used to set the auto on and auto off timer.

1

2

3

4 5

6

7

8

9

10

11 12

14

OPERATING INSTRUCTIONS

15

REMOTE CONTROL

1. Display Panel: Displays the set temperature and

the timer settings. To change the temperature

scale being displayed, press the °C/°F button.

2. Temperature Control Buttons: Used to adjust the

set temperature in 1° increments and the timer

function in 30 minute increments up to 10 hours

and then in 1 hour increments up to 24 hours.

3. Mode Button: Used to choose the operating

mode.

4. Follow Me Button: Used to set the follow me

function.

5. °C/°F button: Use to change the temperature

scale.

6. LED Button: Press to turn the LED back light on

or off.

7. Power Button: Used to turn the appliance on or

off.

8. Sleep Button: Used to set the sleep function.

9. Fan Button: Used to set the fan speed. The fan

can be set to low, medium, high and auto.

10. Timer On Button: Used to set the auto on timer.

11. Timer Off Button: Used to set the auto off timer.

12. Energy Saver Button: Used to set the energy

saver function.

13. Lock Button: Press the °C/°F button and the

timer button at the same time to lock the remote

control and prevent the settings from being

inadvertently changed.

TEMP

1

2

3

4

5

6

7

8

9

10

11

12

13

16

OPERATING INSTRUCTIONS

REMOTE CONTROL BATTERIES

The remote control requires two AAA alkaline batteries (included). Batteries should be replaced when:

a) No sound is heard when attempting to program the appliance.

b) The appliance does not respond to a command issued by the remote control.

Battery replacement:

1. Slide the rear cover on the remote in the direction of the arrow.

2. Insert two AAA batteries following the same orientation depicted inside the battery chamber (+/-).

3. Reinstall the rear cover.

4. If the remote control will not be used for extended periods of time, the batteries should be removed.

Notes:

• Protect the remote control from high temperatures, and keep it away from radiation exposure.

• Keep the control panel receiver out of direct sunlight.

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh,etc) batteries.

• The remote operates within a range of 8 meters (26 ft.) from the receiver located inside the main

appliance. Any obstruction between the receiver and remote may cause signal interference, limiting the

ability to program the main unit.

OPERATING INSTRUCTIONS

17

REMOTE CONTROL REGULATIONS

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

1. Reorient or relocate the receiving antenna

2. Increase the separation between the equipment and receiver

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

4. Consult the dealer or an experienced radio/TV technician for help

Changes or modiﬁ cations not approved by the party responsible for FCC and Industry Canada compliance

could void the user’s authority to operate the equipment. This appliance complies with Part 15 of the FCC

Rules and license-exempt RSS standards.

Operation is subject to the following conditions:

1. This device may not cause interference.

2. This device must accept any interference received, including interference that may cause undesired

operation.

This equipment complies with FCC RF and IC RSS-102 radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm(8

inches) between the radiator and your body.

This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this

device does not cause harmful interference.

This device complies with Canadian CAN ICES-3 (B) / NMB-3 (B)

This device contains:

FCC ID: 24951-MZNA19

IC: 12575A-MDNA19

OPERATING MODES

There are four operating modes to choose from.

Press the mode button repeatedly to choose the

desired mode. The adjacent indicator light will

illuminate to show which mode has been selected.

• Cool Mode

Choose cool mode to set the cooling function.

Use the temperature control buttons to choose the

desired temperature. When cool mode is selected,

the fan speed can be adjusted by pressing the fan

button.

• Dry Mode

Choose dry mode to remove excess moisture

from the air during periods of high humidity. All

water pulled from the air will condense inside the

appliance and drain out the back. The fan speed

will be automatically set and cannot be modiﬁ ed in

dry mode.

• Fan Mode

Choose fan mode to run the internal fan without

engaging the cooling function. Press the fan button

repeatedly to choose the fan speed.

OPERATING MODES

• Auto Mode

Auto mode is a pre-set factory program that

automatically deﬁ nes the mode and fan speed

based on the set temperature, the ambient

temperature and the ambient humidity.

TEMPERATURE CONTROL BUTTONS

The temperature control buttons will modify the set

temperature in 1° increments.

The temperature control buttons will modify the set

time of the timer function in 0.5 hour increments up

to 10 hours and then in 1 hour increments up to 24

hours maximum.

OPERATING INSTRUCTIONS

18

19

OPERATING INSTRUCTIONS

SLEEP

The sleep function can be used to conserve energy

during sleeping hours.

When selected, the set temperature will increase

by 1°C/2°F every half hour for one full hour. The

appliance will hold the new set temperature for

6 hours before automatically returning to normal

operation.

The Sleep Function can be canceled at any time by

pressing the Sleep Button.

ENERGY SAVER

The energy saver function will automatically cycle

the fan on and off when the compressor is not in use

to minimize how often the compressor needs to turn

on.

When selected, the fan will continue to run for 3

minutes after the compressor turns off. The fan will

then cycle on for 2 minutes in 10 minute intervals

until the ambient temperature is above the set

temperature, at which point the compressor will turn

on and cooling will resume.

FOLLOW ME

There is a temperature sensor built into the remote

control that will monitor the room temperature. Keep

the remote control with you and the appliance will

automatically adjust the set temperature based on

the temperature where you are located.

The remote will display the temperature at its

location. The remote will send a signal to the air

conditioner every 3 minutes, so long as you remain

within range of the appliance.

The follow me light on the control panel will

illuminate for 5 seconds every 3 minutes to indicate

that it has received a signal from the remote. If the

appliance does not receive a signal from the remote

during any 7 minute interval it will beep to indicate

that the follow me mode has ended.

The maximum distance for the follow me feature is

8 meters (26 feet). This feature is available in cool

and auto modes.

WIRELESS CONNECTION

This appliance can be controlled with a wireless

application on your wireless device.

Visit https://www.danby.com/support/#apps

to download the application and learn about its

operation.

La page charge ...

Unbranded DAC145EB6WDB6 Le manuel du propriétaire

Ce manuel convient également à

Unbranded DAC145EB6WDB6 Le manuel du propriétaire

dans d''autres langues

Autres documents