Danby DPA065B6WDB-6 Le manuel du propriétaire

Marque: Danby

Modèle: DPA065B6WDB-6

Taper: Le manuel du propriétaire

Ce manuel convient également à

DPA058B6WDB

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

MANUAL DEL PROPIETARIO

www.Danby.com

PORTABLE AIR CONDITIONER

Owner’s Manual.............................1 - 18

CLIMATISEUR PORTABLE

Manuel du propriétaire.................19 - 36

AIRE ACONDICIONADO PORTÁTIL

Manual del propietario.................37 - 54

MODEL • MODÈLE • MODELO

DPA058B6WDB

DPA065B6WDB-6

2020.11.05

Welcome to the Danby family.

We are proud of our quality products and we believe in dependable service. We suggest

that you read this owner’s manual before plugging in your new appliance as it contains

important operation information, safety information, troubleshooting, and maintenance tips

to ensure the reliability and longevity of your appliance.

You are entitled to the warranty coverage as described in the owner’s manual provided with

your new appliance.

1. Please write down your appliance information below. You must keep the original proof

of purchase receipt to validate and receive warranty services.

2. Register your product online and receive a FREE 2 MONTH WARRANTY EXTENSION

after ﬁ lling out a product survey, at www.danby.com/support/product-registration/

Need Help?

1. Read your Owner’s Manual for installation help, troubleshooting, and maintenance

assistance.

2. Visit www.Danby.com to access self-service tools, FAQs and much more by searching

your model number in the search bar.

3. For the Quickest Customer Service, please ﬁ ll out the web form at www.danby.com/

support. Your submission will go directly to an expert on your particular appliance.

Our average response times are between 20 minutes and 2 hours, during EST business

hours.

4. Call 1-800-263-2629 - please note that during peak hours, hold times can exceed one

hour.

Model Number: ____________________________________________________

Serial Number: ____________________________________________________

Date of Purchase: __________________________________________________

SAVE THESE INSTRUCTIONS!

CAUTION: RISK OF FIRE

Flammable refrigerant used. When maintaining

or disposing of the air conditioner, the refrigerant

must not be allowed to vent into the open air.

SAFETY REQUIREMENTS

DANGER: Risk of ﬁ re or explosion. Flammable

refrigerant used. Do not damage the refrigerant

circuit.

• Ensure that servicing is done by factory

authorized service personnel, to minimize

product damage or safety issues.

• Consult repair manual or owner’s guide before

attempting to service this product. All safety

precautions must be followed.

• Dispose of properly in accordance with federal

or local regulations.

• Follow handling instructions carefully.

• Keep ventilation openings, in the appliance clear

of obstruction.

• Do not use mechanical devices or other means

to accelerate the defrosting process.

• Children should be supervised to ensure that

they do not play with the appliance.

• Do not store or install the appliance near

continuously operating ignition sources such as

open ﬂ ames or a gas stove.

• Do not operate near water or in a wet room.

• Do not pierce or burn.

• Be aware that refrigerants may not contain an

odor.

• The appliance must be stored so as to prevent

mechanical damage from occurring.

All wiring must comply with local and national

codes and must be installed by a qualiﬁ ed

electrician. Check the available power supply and

resolve any wiring problems before installing and

operating this appliance.

The rating plate located on the right side of the

appliance just above the power cord contains

electrical and other technical data.

This appliance is not intended for use by persons

(including children) whose physical, sensory or

mental capabilities may be different or reduced,

or who lack experience or knowledge, unless such

persons receive supervision or training to operate

the appliance by a person responsible for their

safety.

GROUNDING INSTRUCTIONS

This appliance must be grounded. Grounding

reduces the risk of electrical shock by providing an

escape wire for the electrical current.

This appliance has a cord that has a grounding

wire with a 3-prong plug. The power cord must be

plugged into an outlet that is properly grounded.

If the outlet is a 2-prong wall outlet, it must be

replaced with a properly grounded 3-prong wall

outlet. The serial rating plate indicates the voltage

and frequency the appliance is designed for.

WARNING - Improper use of the grounding

plug can result in a risk of electric shock.

Consult a qualiﬁ ed electrician or service agent

if the grounding instructions are not completely

understood, or if doubt exists as to whether the

appliance is properly grounded.

Do not connect your appliance to extension

cords or together with another appliance in the

same wall outlet. Do not splice the power cord.

Do not under any circumstances cut or remove the

third ground prong from the power cord. Do not

use extension cords or ungrounded (two prongs)

adapters.

If the power supply cord is damaged, it must be

replaced by the manufacturer, its service agent or

similar qualiﬁ ed person in order to avoid hazard.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Any person involved with working on the refrigerant

circuit should hold a current, valid certiﬁ cate from

an industry accredited assessment authority which

authorizes their competence to handle refrigerants

safely in accordance with an industry recognized

assessment speciﬁ cation.

Servicing shall only be performed as recommended

by the manufacturer. Maintenance and repair

requiring the assistance of other skilled personnel

shall be carried out under the supervision of

the person competent in the use of ﬂ ammable

refrigerants.

When maintaining or disposing of the appliance the

refrigerant must be recovered properly and should

not be allowed to discharge to the air directly.

Information on servicing

1. Checks to the area: Prior to beginning work

on systems containing ﬂ ammable refrigerants,

safety checks are necessary to ensure that the

risk of ignition is minimized. For repair to the

refrigerating system, the following precautions

shall be complied with prior to conducting work

on the system.

2. Work procedure: Work shall be undertaken

under a controlled procedure so as to minimize

the risk of a ﬂ ammable gas or vapour being

present while the work is being performed.

3. General work area: All maintenance staff

and others working in the local area shall

be instructed on the nature of work being

carried out. Work in conﬁ ned spaces shall be

avoided. The area around the work space shall

be sectioned off. Ensure that the conditions

within the work area have been made safe by

removing all ﬂ ammable material.

4. Checking for the presence of refrigerant: The

area shall be checked with an appropriate

refrigerant detector prior to and during work

to ensure the technician is aware of potentially

ﬂ ammable atmospheres. Ensure that the leak

detection equipment being used is suitable

for use with ﬂ ammable refrigerants, i.e. non-

sparking, adequately sealed and intrinsically

safe.

5. Presence of ﬁ re extinguisher: If any hot work is

to be conducted on the refrigeration equipment

or any associated parts, appropriate ﬁ re

extinguishing equipment shall be available

to hand. Have a dry powder or C0

ﬁ re

extinguisher adjacent to the work area.

6. No ignition sources: No person carrying out

work in relation to a refrigeration system which

involves exposing any pipe work that contains

or has contained ﬂ ammable refrigerant shall use

any sources of ignition in such a manner that it

may lead to risk of ﬁ re or explosion. All possible

ignition sources including cigarette smoking,

should be kept sufﬁ ciently far away from the

site of installation, repairing, removing and

disposal during which ﬂ ammable refrigerant can

possibly be released to the surrounding space.

Prior to work taking place, the area around the

equipment is to be surveyed to make sure there

are no ﬂ ammable hazards or ignition risks. No

smoking signs shall be displayed.

7. Ventilated area: Ensure that the area is in the

open or that it is adequately ventilated before

breaking into the system or conducting any hot

work. A degree of ventilation shall continue

during the period that the work is carried out.

The ventilation should safely disperse any

released refrigerant and preferable expel it

externally into the atmosphere.

8. Checks to the refrigeration equipment: Where

electrical components are being changed, they

shall be ﬁ t for the purpose and to the correct

speciﬁ cation. At all times the manufacturer’s

maintenance and service guidelines shall be

followed. If in doubt consult the manufacturer’s

technical department for assistance.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

The following checks shall be applied to installations

using ﬂ ammable refrigerants:

• The charge size is in accordance with the room

size within which the refrigerant containing

parts are installed.

• The ventilation machinery and outlets are

operating adequately and are not obstructed.

• If an indirect refrigerating circuit is being used,

the secondary circuit shall be checked for the

presence of refrigerant.

• Marking to the equipment continues to be visible

and legible. Markings and signs that become

illegible must be corrected.

• Refrigeration pipe or components are installed in

a position where they are unlikely to be exposed

to any substance which may corrode refrigerant

containing components, unless the components

are constructed of materials which are inherently

resistant to being corroded or are suitable

protected against being corroded.

9. Checks to electrical devices: Repair and

maintenance to electrical components shall

include initial safety checks and component

inspection procedures. If a fault exists that

could compromise safety, then no electrical

supply shall be connected to the circuit until it

is satisfactorily dealt with. If the fault cannot

be corrected immediately but it is necessary to

continue operation, an adequate temporary

solution shall be used. This shall be reported to

the owner of the equipment so all parties are

advised.

Initial safety checks shall include:

• That capacitors are discharged. This shall be

done in a safe manner to avoid possibility of

sparking.

• That no live electrical components and wiring

are exposed while charging, recovering or

purging the system.

• That there is continuity of earth bonding.

Repairs to sealed components

1. During repairs to sealed components, all

electrical supplies shall be disconnected from

the equipment being worked upon prior to any

removal of sealed covers, etc. If it is absolutely

necessary to have an electrical supply to

equipment during servicing then a permanently

operating form of leak detection shall be located

at the most critical point to warn of a potentially

hazardous situation.

2. To ensure that by working on electrical

components the casing is not altered in such

a way that the level of protection is affected,

particular attention shall be paid to the

following:

• Damage to cables, excessive number of

connections, terminals not made to original

speciﬁ cation, damage to seals, incorrect ﬁ tting

of glands, etc.

• Ensure the apparatus is mounted securely.

• Ensure that seals or sealing materials have

not degraded such that they no longer serve

the purpose of preventing the ingress of

ﬂ ammable atmospheres. Replacement parts

shall be in accordance with the manufacturer’s

speciﬁ cations.

Note: The use of silicon sealant may inhibit the

effectiveness of some types of leak detection

equipment. Intrinsically safe components do not

have to be isolated prior to working on them.

Repair to intrinsically safe components

Do not apply any permanent inductive or

capacitance loads to the circuit without ensuring

that this will not exceed the permissible voltage

and current permitted for the equipment in use.

Intrinsically safe components are the only types that

can be worked on while live in the presence of a

ﬂ ammable atmosphere. The test apparatus shall

be at the correct rating. Replace components only

with parts speciﬁ ed by the manufacturer. Other

parts may result in the ignition of refrigerant in the

atmosphere from a leak.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Removal and evacuation

When breaking into the refrigerant circuit to make

repairs or for any other purpose conventional

procedures shall be used. However, it is important

that the best practice is followed since ﬂ ammability

is a consideration. The following procedures shall

be adhered to:

• Remove refrigerant.

• Purge the circuit with inert gas.

• Evacuate.

• Purge again with inert gas.

• Open the circuit by cutting or brazing.

• The refrigerant charge shall be recovered into

the correct recovery cylinders. The system shall

be ﬂ ushed with OFN to render the unit safe. This

process may need to be repeated several times.

Compressed air or oxygen shall not be used for

this task.

• Flushing shall be achieved by breaking the

vacuum in the system with OFN and continuing

to ﬁ ll until the working pressure is achieved, then

venting to atmosphere and ﬁ nally pulling down

to a vacuum. This process shall be repeated until

no refrigerant is within the system. When the

ﬁ nal OFN charge is used, the system shall be

vented down to atmospheric pressure to enable

work to take place. This operation is absolutely

vital is brazing operations on the pipe-work are

to take place.

• Ensure that the outlet for the vacuum pump is

not close to any ignition sources and there is

ventilation available.

Charging procedures

In addition to conventional charging procedures, the

following requirements shall be followed:

• Ensure that contamination of different

refrigerants does not occur when using charging

equipment. Hoses or lines shall be as short as

possible to minimize the amount of refrigerant

contained in them.

• Cylinders shall be kept upright.

• Ensure that the refrigeration system is earthed

prior to charging the system with refrigerant.

• Label the system when charging is complete, if

not already labeled.

• Extreme care shall be taken not to overﬁ ll the

refrigeration system.

• Prior to recharging the system it shall be

pressure tested with OFN. The system shall be

leak tested on completion of charging but prior

to commissioning. A follow up leak test shall be

carried out prior to leaving the site.

Cabling

Check that cabling will not be subject to wear,

corrosion, excessive pressure, vibration, sharp

edges or any other adverse environmental effects.

The check shall also take into account the effects of

aging or continual vibration from sources such as

compressors or fans.

Detection of ﬂ ammable refrigerants

Under no circumstances shall potential sources of

ignition be used in the searching for or detection

of refrigerant leaks. A halide torch or any other

detector using a naked ﬂ ame shall not be used.

Leak detection methods

The following leak detection methods are deemed

acceptable for systems containing ﬂ ammable

refrigerants:

• Electronic leak detectors shall be used to detect

ﬂ ammable refrigerants but the sensitivity may

not be adequate or may need recalibration.

Detection equipment shall be calibrated in a

refrigerant-free area. Ensure that the detector is

not a potential source of ignition and is suitable

for the refrigerant used.

• Leak detection equipment shall be set at a

percentage of the LFL of the refrigerant and

shall be calibrated to the refrigerant employed

and the appropriate percentage of gas (25%

maximum) is conﬁ rmed.

• Leak detection ﬂ uids are suitable for use with

most refrigerants but the use of detergents

containing chlorine shall be avoided as the

chlorine may react with the refrigerant and

corrode the copper or pipe-work.

• If a leak is suspected, all naked ﬂ ames shall be

removed or extinguished.

• If a leakage of refrigerant is found which

requires brazing, all of the refrigerant shall be

recovered from the system or isolated by means

of shut off valves in a part of the system remote

from the leak. Oxygen free nitrogen (OFN) shall

then be purged through the system both before

and during the brazing process.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Decommissioning

Before carrying out this procedure, it is essential

that the technician is completely familiar with the

equipment in all its detail. It is recommended good

practice that all refrigerants are recovered safely.

Prior to the task being carried out, an oil and

refrigerant sample shall be taken in case analysis is

required prior to re-use of reclaimed refrigerant. It

is essential that electrical power is available before

the task is commenced.

A. Become familiar with the equipment and its

operation.

B. Isolate system electrically.

C. Before attempting the procedure ensure that:

• Mechanical handling equipment is available

if required for handling refrigerant cylinders.

• All personal protective equipment is

available and being used correctly.

• The recovery process is supervised at all

times by a competent person.

• Recovery equipment and cylinders conform

to the appropriate standards.

D. Pump down refrigerant system, if possible.

E. If a vacuum is not possible, make a manifold so

that refrigerant can be removed from various

parts of the system.

F. Make sure that cylinder is situated on the scales

before recovery takes place.

G. Start the recovery machine and operate in

accordance with the manufacturer’s instructions.

H. Do not overﬁ ll cylinders. No more than 80%

volume liquid charge.

I. Do not exceed the maximum working pressure

of the cylinder, even temporarily.

J. When the cylinders have been ﬁ lled correctly

and the process is completed, make sure that the

cylinders and the equipment are removed from

the site promptly and all isolation valves on the

equipment are closed off.

K. Recovered refrigerant shall not be charged into

another refrigeration system unless it has been

cleaned and checked.

Labeling

Equipment shall be labeled stating that it has been

decommissioned and emptied of refrigerant. The

label shall be dated and signed. Ensure that there

are labels on the equipment stating the equipment

contains ﬂ ammable refrigerant.

Recovery

When removing refrigerant from a system, either for

servicing or decommissioning, it is recommended

good practice that all refrigerants are removed

safely.

When transferring refrigerant into cylinders, ensure

that only appropriate refrigerant recovers cylinders

are employed. Ensure that the correct number of

cylinders for holding the total system charge are

available. All cylinders to be used are designed

for the recovered refrigerant and labeled for that

refrigerant, i.e. special cylinders for the recovery

of refrigerant. Cylinders shall be complete with

pressure relief valve and associated shut-off valves

in good working order. Empty recovery cylinders

are evacuated and, if possible, cooled before

recovery occurs.

The recovery equipment shall be in good working

order with a set of instructions concerning the

equipment that is at hand and shall be suitable for

the recovery of ﬂ ammable refrigerants. In addition,

a set of calibrated weighing scales shall be

available and in good working order. Hoses shall

be complete with leak-free disconnect couplings

and in good condition. Before using the recovery

machine, check that is it in satisfactory working

order, has been properly maintained and that any

associated electrical components are sealed to

prevent ignition in the event of a refrigerant leak.

Consult the manufacturer if in doubt.

The recovered refrigerant shall be returned to the

refrigerant supplier in the correct recovery cylinder

and the relevant waste transfer note shall be

arranged. Do not mix refrigerants in recovery units

and especially not in cylinders. If compressors or

compressor oils are to be removed, ensure that they

have been evacuated to an acceptable level to make

certain that ﬂ ammable refrigerant does not remain

within the lubricant. The evacuation process shall be

carried out prior to returning the compressor to the

suppliers. Only electric heating to the compressor

body shall be employed to accelerate this process.

When oil is drained form a system, it shall be

carried out safely.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

INSTALLATION INSTRUCTIONS

ACCESSORIES

1. Air outlet adapter

2. Exhaust hose

3. Window slider adapter

4. 2 Bolts

5. Window slider A

6. Window slider B and C

7. Foam seal A (adhesive)

8. Foam seal B (adhesive)

9. Foam seal C (non-adhesive)

10. Security bracket and 2 screws

11. Drain hose

12. Power cord storage band

13. Remote control and batteries

REQUIRED TOOLS

1. Medium sized Phillips screwdriver

2. Tape measure or ruler

3. Knife or scissors

4. Saw (in the event that the window sliders need to

be cut to size)

ON/OFF

TEMP

MOD E

FAN

LED

SLEEP

SWING

IMPORTANT WARNING

Do not leave this appliance unattended

in a space where people or animals who

cannot react to a malfunction are located. A

malfunction such as the exhaust hose becoming

dislocated, can cause extreme overheating or

death in an enclosed, unattended space.

INSTALLATION INSTRUCTIONS

INSTALLING THE WINDOW KIT

The instructions below can be used for either a hung

window or a sliding window application.

1. Measure the window opening where the window

kit will be installed. Assemble as many sliders

as necessary to ﬁ t the window. If the window

opening is less than the minimum length of a

single slider, use the slider that has the hole in it

and cut it to the correct length. Make sure not to

cut the end that has the hole as this is necessary

to attach the exhaust hose adapter. Cut the

adhesive foam seals to the correct length for the

window and attach them to the window sash

and frame.

2. Connect the window slider adapter to the

window slider by gently pressing it into the hole

in the slider until it clicks into place.

3. Attach the exhaust hose to the window slider

adapter by gently pressing it into the adapter

until it clicks into place.

4. Install the slider kit and hose assembly and close

the window to hold it in place.

5. Attach the air outlet adapter to the back of the

appliance by sliding it down into the channel

around the air outlet. Attach the hose to the air

outlet adapter on the back of the appliance by

gently pressing it into the adapter until it clicks

into place.

6. Cut the non-adhesive foam seal to match the

width of the window and insert it between the

glass and the window frame to prevent air and

insects from getting into the room.

7. Install the security bracket in the window frame

with the provided screws.

Note: Do not over extend or bend the hose as this

will impede air ﬂ ow.

FEATURES

Front

1. Control panel

2. Horizontal louver

3. Casters

Rear

1. Upper air ﬁ lter and air intake

2. Handles

3. Continuous drain outlet

4. Air outlet

5. Lower air ﬁ lter and air intake

6. Power cord buckle

7. Lower drain outlet

LOCATION

Place the air conditioner on a smooth, level ﬂ oor

that is strong enough to support it and all included

accessories.

Make sure the appliance is level to minimize noise

and vibration.

The appliance must be installed near a grounded

receptacle and the overﬂ ow drain outlet on the rear

of the appliance must be accessible.

Do not cover air inlets or outlets or the remote

control receiver on the control panel.

The appliance requires 50 cm (20 inches) of

clearance on the front and sides.

The appliance requires at least 50 cm (20 inches) of

clearance on the back.

INSTALLATION INSTRUCTIONS

OPERATING INSTRUCTIONS

3sec

3 4

CONTROL PANEL

1. Swing button: Press to start the auto swing

feature. When auto swing is activated, press

again to stop the louver at the desired angle.

2. Sleep and ﬁ lter button:

• Press to start the sleep feature.

• The ﬁ lter light will illuminate after 250 hours of

use as a reminder to clean the ﬁ lter; to reset the

ﬁ lter after cleaning, press and hold the sleep

button for three seconds.

3. Timer button: Press to start the automatic timer.

Light will indicate whether a timer is set.

4. Fan button:

• Press to select fan speed. Light will indicate

current speed.

• Press and hold for 3 seconds to turn the

continuous fan on or off.

5. Mode button: Press to select the desired mode.

Light will indicate current mode.

6. LED display:

• Shows the set temperature in °C or °F.

• Shows the timer settings.

• While on dry and fan mode, shows the room

temperature.

7. Temperature control buttons:

• Used to set the temperature.

• Press and hold both temperature control buttons

for three seconds to change the temperature

display from °C to °F.

8. Power button: Press to turn the appliance on or

off.

OPERATING MODES

Cool Mode

Choose cool mode to set the cooling function.

• Use the temperature control buttons to choose

the desired temperature.

• Use the fan button to choose the desired fan

speed.

• The temperature can be set within a range of 17

- 30°C (62 - 86°F).

• The exhaust hose should be installed during cool

mode to ensure the best results.

Dry Mode

Choose dry mode to remove excess moisture from

the air. Water will condense inside the appliance

and drain out the back.

• The humidity level and fan speed will be

automatically set and cannot be modiﬁ ed in dry

mode.

• The exhaust hose does not need to be installed

during dry mode.

• It may be necessary to install the continuous

drain hose during dry mode to remove excess

water.

Fan Mode

Fan mode can be used to run the fan without

engaging the cooling or dehumidifying functions.

• Press the fan button to choose the desired fan

speed.

• The exhaust hose does not need to be installed

during fan mode.

• In cooling or dry mode, press and hold the

fan button for 3 seconds to set the fan to run

continuously. Press and hold the fan button for 3

seconds to disengage the continuous fan. During

normal operation the fan will turn on and off

with the compressor.

Auto Mode

Auto mode is a pre-set factory program that

automatically deﬁ nes the mode (cool or fan) and

fan speed based on the set temperature and the

ambient temperature. The exhaust hose should be

installed during dry mode.

OPERATING INSTRUCTIONS

FOLLOW ME

There is a temperature sensor built into the remote

control that will continuously collect the current

room temperature. Keep the remote control with

you and the appliance will automatically adjust the

set temperature based on the current temperature

where you are located to reach the most

comfortable condition and temperature.

Press the follow me button to activate the follow

me function. The remote will display the current

temperature at its location. The remote will send

a signal to the air conditioner every 3 minutes, so

long as you remain within range of the appliance.

The follow me light on the control panel of the

appliance will illuminate for 5 seconds every three

minutes to indicate that it has received a signal

from the remote. If the appliance does not receive a

signal from the remote during any 7 minute interval,

it will beep to indicate that the follow me mode has

ended.

The maximum distance for the follow me feature is

8 meters (26 feet). This feature is available in cool

and auto modes.

SLEEP

The sleep function can be used to conserve energy

during sleeping hours.

When selected, the set temperature will increase

by 1°C/2°F every half hour for one full hour. The

appliance will hold the new set temperature for

6 hours before automatically returning to normal

operation.

The sleep function can be canceled at any time by

pressing the sleep button.

TIMER

Auto Off

1. When the air conditioner is turned on, press the

timer button to activate the auto off timer.

2. Press the temperature control buttons to change

the set time in 0.5 hour increments up to 10

hours and then in 1 hour increments up to 24

hours.

Auto On

1. When the air conditioner is turned off, press the

timer button to activate the auto on timer.

2. Press the temperature control buttons to change

the set time in 0.5 hour increments up to 10

hours and then in 1 hour increments up to 24

hours.

Using Auto On and Auto Off Together

The auto on and auto off timers can be used at the

same time by ﬁ rst setting one and then the other.

For example, if the air conditioner is running,

you can set the auto off timer to let it run for a set

amount of time before turning off and then set the

auto on timer to turn it back on at a later time.

Or, if the air conditioner is not running, you can set

the auto on timer to turn it on at a later time and

then set the auto off timer to shut it off after running

for a period of time.

Note: The timer will not cycle the air conditioner on

and off indeﬁ nitely. The auto on and auto off timers

will function one time and then the air conditioner

will return to regular functioning.

Turning the air conditioner on or off at any time

or changing the timer setting to 0.0 will cancel the

timer settings.

OPERATING INSTRUCTIONS

REMOTE CONTROL

1. Power button: Press to turn the appliance on or

off.

2. Mode button: Press to select the desired mode.

3. Fan button: Press to select fan speed.

4. Sleep button: Press to start the sleep feature.

5. Swing button: Press to start the auto swing

feature. When auto swing is activated, press

again to stop the louver at the desired angle.

6. Follow me button: Press to activate the follow

me feature.

7. LED button: Press to turn the LED display on or

off.

8. Timer off button: Press to set the automatic off

timer.

9. Timer on button: Press to set the automatic on

timer.

10. Shor tcut button: Press to set and activate the

short cut function.

11. Temperature control buttons:

• Used to set the temperature.

• Press and hold both temperature control buttons

for 3 seconds to change the temperature display

from °C to °F.

12. LED display: Shows the set temperature in °C or

°F or the auto-timer settings.

4 5

6 7

Shortcut function (only available on remote):

• Used to save a favourite setting.

• Set the appliance to the temperature and fan

speed that you would like to set as a favourite.

• Press and hold the shortcut button for 2 seconds.

• Press the shortcut button at any point in future to

return to the favourite setting.

• If no favourite is set, pressing the shortcut button

will cause the appliance to run in auto mode at

29°C (79°F), with fan speed set to auto.

OPERATING INSTRUCTIONS

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential

installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will

not occur in a particular installation.

If this equipment does cause harmful interference

to radio or television reception, which can be

determined by turning the equipment off and on, the

user is encouraged to try to correct the interference

by one or more of the following measures:

1. Reorient or relocate the receiving antenna

2. Increase the separation between the equipment

and receiver

3. Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected

4. Consult the dealer or an experienced radio/TV

technician for help

Changes or modiﬁ cations not approved by the

party responsible for FCC compliance could void

the user’s authority to operate the equipment. This

appliance complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference

received, including interference that may cause

undesired operation.

This device complies with Canadian CAN ICES-3

(B) / NMB-3 (B)

REPLACING THE REMOTE BATTERIES

This air conditioner comes with two AAA batteries.

Place the batteries in the remote control before use.

1. Slide the back cover from the remote downward

to expose the battery compartment.

2. Insert the batteries, ensure to match the (+) and

(-) symbols on the ends of the batteries with the

symbols inside the battery compartment.

3. Slide the battery cover back into place.

Notes:

• The air conditioner will not respond if curtains,

doors or other materials block the signal from

the remote control to the unit.

• Prevent any liquid from contact with the remote

control. Do not expose the remote control to

direct sunlight or heat.

• If the infrared signal receiver on the indoor unit

is exposed to direct sunlight, the air conditioner

may not function properly. Use curtains to

prevent the sunlight from falling on the receiver.

• Do not mix old and new batteries or batteries of

different types.

• Do not leave the batteries in the remote control

if it is not going to be used for more than 2

months.

IMPORTANT

Do not dispose of batteries as unsorted municipal

waste. Refer to local laws for proper disposal of

batteries.

OPERATING INSTRUCTIONS

WATER DRAINAGE

When the internal drain pan becomes full the appliance will

beep 8 times and the digital display will show error code P1.

The air conditioning or dehumidifying action will stop but the

fan may continue to operate.

There are two methods to drain water from the appliance.

1. Drain Plug

1. Turn the appliance off and unplug it from the power source.

2. Carefully move the appliance to a location where the water

can be drained.

3. Remove the drain plug and allow the water to completely

drain.

4. Replace the bottom drain plug, pressing ﬁ rmly to ensure a

tight ﬁ t and no leaks.

5. The P1 error symbol will disappear and the appliance will

resume regular function once power is restored.

2. Continuous Drain

During the dry mode, you may wish to set up the continuous

drain option so that the appliance will automatically drain

collected water.

Remove the exhaust hose during dry mode, it is not necessary.

Ensure that the appliance is turned off and unplugged from the

power source before setting up the drain hose.

Remove the upper drain plug and attach the drain hose that

was provided with the appliance. Ensure that there are no

kinks or bends in the drain hose as this can stop water from

draining.

Place the open end of the drain hose over the receptacle that

the appliance will drain into; this could be a basement ﬂ oor

drain, a sink or similar.

Remember that there is no drain pump in this appliance, the

continuous drain is activated by gravity only. Ensure that the

drain hose goes straight down toward the ﬂ oor from the drain

connection. If the hose is not positioned directly downwards,

water will not drain correctly.

CARE & MAINTENANCE

CLEANING

• Unplug the appliance before cleaning or

servicing.

• Clean the cabinet with a lukewarm damp cloth

and neutral detergent. Dry the cabinet with a

lint-free dry cloth.

• Do not use gasoline, paint thinner or other

chemicals to clean the appliance.

• Do not wash the appliance directly under a tap

or using a hose. It may cause electrical damage.

AIR FILTER

There are three air ﬁ lters in this appliance. Air

ﬁ lters should be cleaned every two weeks to ensure

efﬁ cient performance.

In households with animals, the air ﬁ lters may need

to be cleaned more often and the external grills may

need to be wiped to prevent blocked air ﬂ ow.

LONG-TERM STORAGE

1. Drain all water from the appliance.

2. Run the appliance on Fan mode for half a day in

a warm room to dry the inside of the appliance

and prevent mold formation.

3. Turn off the appliance and unplug it, wrap the

cord and bundle it with tape.

4. Remove the batteries from the remote control.

5. Clean the air ﬁ lters and reinstall them.

6. Store the appliance is a cool, dark place.

Prolonged exposure to direct sunlight or extreme

heat can shorten the lifespan of the appliance.

DISPOSAL

This appliance should not be treated as regular

household waste. Check for local regulatory

compliance regarding the approved and safe

disposal of this appliance.

ERROR CODES

E1 - room temperature sensor error

E2 - evaporator temperature sensor error

E4 - display panel communication error

E7 - signal detection error

P1 - water tray is full - attach drain hose and drain

excess water

FREQUENTLY ASKED QUESTIONS

Can I leave my AC in place through the winter?

This is not recommended.

What are the standard wattage and amps used?

Information pertaining to watts and amps can be found on the rating plate located on the side of the unit.

When should I use the exhaust hose?

The exhaust hose should be used in cool and auto modes. It is not required in fan and dry modes.

Can I use an extension cord?

No, an extension cord may not be used.

Can I extend the length of the exhaust hose?

No. The unit was designed with the length of the hose in mind and has only been tested under those

conditions. Instead use an additional fan to blow the cool air to other locations.

When should I use the drain hose?

The drain hose should be used in heat mode, dry mode or if using the continuous drain.

Where do I drain water from?

The water drains from the drainage port. If you are not using the continuous drain, the internal pan drains

from the bottom outlet.

Odors

Odour is caused by the formation of mold or mildew on internal surfaces. This can happen when there is

poor air circulation, a dirty ﬁ lter or the air conditioner was not used for a period of time.

• Ensure the ﬁ lter is clean.

• Run the unit on fan mode to remove any internal moisture.

• Check for any blockages in the drain lines and ensure there are no obstructions.

Please give your unit a hard reboot. Unplug it and plug it back in after 15-20 minutes. This allows the unit

to warm and drain if there is any frost stopping draining and go back to factory settings

For odour in a unit, we suggest using an algaecide tablet. You ﬁ rst need to turn the unit off, remove the

lower grill and ﬁ lter from the grill at the base of the unit, and then place the tablet in base.

TROUBLESHOOTING

Appliance will not operate

• Plug is not fully inserted into the wall outlet

• Blown fuse or circuit breaker

Insufﬁ cient cooling

• Air ﬁ lter is dirty

• Blocked air ﬂ ow

• Appliance size is too small for application

Noise

• Inadequate support in window installation; double check that all screws are tight and the installation is

secure

Odors

• Formation of mold or mildew on internal wet surfaces

• Place an algaecide tablet in the base pan; ensure the appliance is unplugged, remove the upper grille

and ﬁ lter, place the tablet in the middle water tray and replace the grille and ﬁ lter

LIMITED IN-HOME APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating

conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter

“Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.

First Year

During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s

option, at no charge to the ORIGINAL purchaser.

To obtain

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance

Service

requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at

their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.

Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service

must be performed by a qualied service technician.

If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all

obligations of Danby under this warranty shall be void.

Boundaries of

If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be

In Home Service

delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for

warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he

responsibility of the purchaser.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due

to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its

authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees

under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages

to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of

the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions

(extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).

Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our

AUTHORIZED SERVICE DEPOT.

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

04/09

1-800-263-2629

Warranty Service

In-home

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an authorized service

depot. Any appliance requiring service outside the limited boundaries of “In Home Service”, will be the consumer’s

responsibility to transport at their own expense to the original point of purchase or a service depot for repair. If the

appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center, it must

be delivered to the nearest authorized Danby Service Depot by the purchaser.

Transportation charges to and from the service location are not protected by this warranty and are the

responsibility of the purchaser.

During the ﬁrst twenty four (24) months, any functional parts of this product found to be defective, will be repaired

or replaced, at warrantor’s option, at no charge to the original purchaser.

Contact the dealer where the unit was purchased, or contact the nearest authorized Danby service depot, where

service must be performed by a qualiﬁed service technician. If service is performed on the unit by anyone other

than an authorized service depot, all obligations of Danby under this warranty shall be void.

First 24 months

To obtain service

Boundaries of

in-home service

LIMITED “IN HOME” WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used

under the normal operating conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby

Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts are warranted for thirty (30) days from the date of purchase, with no extensions provided.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other

contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or implied, made

or intended by Danby or its authorized distributors and all other warranties, conditions, representations or guarantees, including any

warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation or statute is hereby expressly

excluded. Save as herein provided, Danby shall not be responsible for any damages to persons or property, including the unit itself,

howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of the unit, the

purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or property caused by

the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating

conditions (ie. extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, ﬂoods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for outdoor

application, including but not limited to: garages, patios, porches or anywhere that is not properly insulated or climate controlled).

Proof of purchase date will be required for warranty claims; retain bills of sale. In the event that warranty service is required, present

the proof of purchase to our authorized service depot.

Warranty Service

In Home

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

1-800-263-2629

04/17

Bienvenue dans la famille Danby.

Nous sommes ﬁ ers de nos produits de qualité et nous croyons en un service ﬁ able. Nous

vous suggérons de lire ce manuel du propriétaire avant de brancher votre nouvel appareil

car il contient des informations de fonctionnement importantes, des informations de

sécurité, des conseils de dépannage et d’entretien pour assurer la ﬁ abilité et la longévité de

votre appareil.

Vous avez droit à la couverture de la garantie décrite dans le manuel du propriétaire fourni

avec votre nouvel appareil.

1. Veuillez noter ci-dessous les informations relatives à votre appareil. Vous devez

conserver la preuve d’achat originale pour valider et bénéﬁ cier des services de garantie.

2. Enregistrez votre produit en ligne et recevez une PROLONGATION DE GARANTIE

GRATUITE DE 2 MOIS après avoir rempli une enquête sur les produits, à l’adresse

www.danby.com/support/product-registration/

Besoin d’assistance?

1. Lisez votre manuel du propriétaire pour obtenir de l’aide à l’installation, au dépannage

et à la maintenance.

2. Visitez www.Danby.com pour accéder aux outils en libre-service, aux FAQ et bien plus

encore en recherchant votre numéro de modèle dans la barre de recherche.

3. Pour bénéﬁ cier du service client le plus rapide, veuillez remplir le formulaire Web à

l’adresse www.danby.com/support. Votre soumission ira directement à un expert de

votre appareil particulier. Nos temps de réponse moyens sont compris entre 20 minutes

et 2 heures, pendant les heures ouvrables EST.

4. Composez le 1-800-263-2629 - veuillez noter que pendant les heures de pointe, les

temps d’attente peuvent dépasser une heure.

Numéro de modèle : _______________________________________________

Numéro de serie : _________________________________________________

Date d’achat : _____________________________________________________

La page charge ...

Danby DPA065B6WDB-6 Le manuel du propriétaire

Marque: Danby

Modèle: DPA065B6WDB-6

Taper: Le manuel du propriétaire

Ce manuel convient également à

DPA058B6WDB

Télécharger le PDF

rapport

dans d''autres langues

English: Danby DPA065B6WDB-6 Owner's manual
español: Danby DPA065B6WDB-6 El manual del propietario

Danby DPA065B6WDB-6 Le manuel du propriétaire

Ce manuel convient également à

Danby DPA065B6WDB-6 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents