Thrustmaster RUN'N' DRIVE WIRELESS 3-IN-1 Le manuel du propriétaire

CouvQI_RunNdrive3in15075295.indd1 1 13/06/07 12:19:42

1/14

User Manual

TECHNICAL FEATURES

1. 2 independent vibrating motors

(for PlayStation® 2)

2. 2 progressive analog mini-sticks

3. D-Pad

4. Progressive optical wheel

5. 2 progressive triggers

6. HOME LED button for Playstation®3

and MODE for PC

7. MAPPING LED button (for programming

and indicating connection status)

8. PRESET LED button

(to select programming)

9. Action buttons

10. PC and PlayStation® 3 USB connector

11. “PC” or “PS3” USB selector

12. CONNECT LED button on receiver

13. PlayStation® 2 “Gameport” connector

14. Battery compartment

15. POWER ON/OFF switch

16. MOTORS ON/OFF switch

2/14

TABLE OF SUPPORTED MODES

Platform MODE

Color of HOME button

(6)

PLAYSTATION®

1

“PS1” OFF

PLAYSTATION® 2 “PS2” RED

PLAYSTATION® 3 “PS3” RED

“4 AXES” GREEN

PC

“6 AXES” RED

INSTALLING BATTERIES

Insert 2 LR03 / AAA type batteries in the battery compartment situated on the back of the gamepad (14).

OVERVIEW

• POWER ON/OFF switch (15)

- OFF position = the gamepad is off (and doesn’t use up batteries).

- ON position = the gamepad is on.

• MOTORS ON/OFF switch (16)

- OFF position = vibration mode is disabled (uses less battery power).

- ON position = vibration mode is enabled (uses more battery power).

• “PC / PS3” USB selector (11)

Must always be set to the correct position before connecting your receiver’s USB connector.

• MAPPING (7) and CONNECT (12) blue LEDs

- Both LEDs are on = connection established between gamepad and receiver.

- Both LEDs flash quickly = no connection between gamepad and receiver.

- The MAPPING LED is off = the gamepad is in standby mode or powered off.

- The MAPPING LED flashes slowly & continuously = please change batteries.

THE CONNECTION BETWEEN THE GAMEPAD AND RECEIVER

IS ESTABLISHED AUTOMATICALLY

To force the connection in case of error: press the CONNECT button on the receiver

and simultaneously press the L2 + R2 + MAPPING buttons on your gamepad.

• STANDBY MODE

The gamepad switches off automatically:

- After 5 minutes of inactivity

- After 5 seconds in the event of error or loss of connection.

To wake up your gamepad: press START or use the POWER ON/OFF switch (15).

3/14

PLAYSTATION® 3

INSTALLATION ON PLAYSTATION® 3

1. Set your receiver’s USB selector to the “PS3” position.

2. Connect the USB connector to USB port #1 on the console.

3. Switch on your console.

4. Switch on your gamepad using the POWER ON/OFF switch (15).

5. Once a connection has been established: start up your game.

You are now ready to play!

PLAYSTATION® 3 MODE

“AUTOMATIC PRESET” CONFIGURATION - PLAYSTATION® 3

PS3 mode Red HOME button

Here:

• “Optical wheel” associated with “Left/Right”

direction on left mini-stick

• “Right trigger” associated with progressive

“R2” button

• “Left trigger” associated with progressive “L2”

button

USING THE “HOME” BUTTON (6)

Your gamepad’s “HOME” button allows you to exit games, access menus and directly switch off your

PlayStation®3 system.

IMPORTANT NOTES FOR PLAYSTATION® 3

- The USB selector on your receiver (11) must always be set to “PS3” before connecting the receiver.

- In “1 Player” mode: If your official gamepad is powered on, you must switch it to “gamepad port 2” in order

for your “Run’N’ Drive” gamepad to be functional.

- On PlayStation® 3, the “Run’N’ Drive” gamepad is only compatible with PlayStation® 3 games (and will

not work with PlayStation® 2 games) and does not feature a motion sensor.

4/14

PLAYSTATION® 2

INSTALLATION ON PLAYSTATION® 2

1. Connect the receiver’s PS2 Gameport connector (13) to port #1 on the console.

2. Switch on your console.

3. Switch on your gamepad using the POWER ON/OFF switch (15).

4. Once a connection has been established: start up your game.

You are now ready to play!

PLAYSTATION® 2 MODE

“AUTOMATIC PRESET” CONFIGURATION - PLAYSTATION® 2

PS2 mode Red HOME button

Here:

• “Optical wheel” associated with

“Left/Right” direction on left mini-stick

• “Right trigger” associated with progressive

“Cross” button

• “Left trigger” associated with progressive

“Square” button

IMPORTANT NOTE FOR PLAYSTATION® 2

Never connect the USB connector (10) to your PlayStation® 2 (to avoid the risk of damaging your gamepad or

your console).

5/14

PC

INSTALLATION ON PC

1. Set the USB selector on the receiver (11) to the “PC” position.

2. Connect the receiver’s USB connector to one of your computer’s USB ports. Windows® XP or Vista will

automatically detect the new device.

3. Switch on your gamepad using the POWER ON/OFF switch (15).

4. Click Start/Settings/Control Panel and then double-click Game Controllers.

The Game Controllers dialog box displays the gamepad’s name with OK status.

5. In the Control Panel, click Properties to test and view the buttons, D-pad, mini-sticks, triggers and

optical wheel.

You are now ready to play!

IMPORTANT NOTES FOR PC

- The USB selector on your receiver (11) must always be set to “PC” before connecting the receiver.

- “Advanced Programming Software” for PC is also available for download on our website at the following

address:

http://ts.thrustmaster.com/

SELECTING “AXES” ON PC

• Selecting axes via “Software”:

After installing the “Advanced Programming Software”, go to page 1 of the Control Panel, click the

number of axes you wish to use and then click OK.

• Selecting axes via “Hardware”:

Press the HOME button (6) to select the number of active axes.

6/14

2 “AXES” MODES AVAILABLE ON PC

“AUTOMATIC PRESET” CONFIGURATION - PC

“4 AXES” mode Green HOME button

Here:

• “Optical wheel” associated with “Left/Right”

direction on left mini-stick

• “Right trigger” associated with “Up”

direction on right mini-stick

• “Left trigger” associated with “Down”

direction on right mini-stick

“7 AXES” mode Red HOME button

Here:

• “Optical wheel”

is now independent

• “Right trigger”

is now independent

• “Left trigger”

is now independent

To find out all of the possibilities offered on PC,

try them out in the Windows “Game Controllers” section

(once you have installed the “Advanced Programming Software”)

7/14

ADVANCED FUNCTIONS

ADJUSTING THE OPTICAL WHEEL’S SENSITIVITY

The optical wheel (4) has 2 sensitivity modes:

- Normal sensitivity (the default mode)

- High sensitivity (must be set)

• Setting “High Sensitivity” mode:

Steps Action HOME button

1 Raise and hold the “UP” direction on the optical wheel

2 Press and release the MAPPING button (7)

Flashes continuously

Your optical wheel is now more sensitive

(Procedure must be carried out each time the gamepad restarts or is disconnected)

• Returning to “Normal Sensitivity” mode:

Steps Action HOME button

1 Lower and hold the “DOWN” direction on the optical wheel

2 Press and release the MAPPING button (7)

Does not flash

Your optical wheel has now returned to Normal Sensitivity (the default mode)

2 PROGRAMMING MODES

The PRESET button and LED (8) allows you to view the type of programming selected:

AUTOMATIC (preprogrammed) or MANUAL (programmed by yourself). A single press of this button

allows you (even during the course of a game) to switch from one programming mode to the other.

• “AUTOMATIC PRESET” (PRESET button OFF)

This represents the default programming: the functions of the optical wheel and the triggers are

preprogrammed, as are the positions of the buttons and the directions of the mini-sticks and of the D-Pad.

PLEASE REFER TO THE “AUTOMATIC PRESET” CONFIGURATION DIAGRAMS

• “MANUAL PRESET” (PRESET button GREEN)

This represents your own personal programming:

- The buttons, directions of the mini-sticks and of the D-Pad can either be

* programmed on the optical wheel and on the triggers,

* or switched between themselves.

- You can modify the programming to your liking and whenever you wish.

- The programming is automatically saved inside your gamepad (even when disconnected).

- When your “MANUAL PRESET” is clear, it is identical to the “AUTOMATIC PRESET”.

8/14

PROGRAMMING THE OPTICAL WHEEL AND TRIGGERS

The 2 directions of the optical wheel and the 2 progressive triggers can be programmed using the

MAPPING button (7).

• Examples of possible applications:

Programming a button, direction of a mini-stick or of the D-Pad:

- onto the “up” or “down” direction of the optical wheel

- onto the “right trigger” or “left trigger”

• Programming procedure on optical wheel and triggers:

Steps Action

PRESET button

color

1 Enable “MANUAL PRESET” (8) by pressing the button. Lit up green

2 Press and release the MAPPING button (7). Lit up red

3 Press and release the button or direction to program. Flashes red

4

Raise or lower the direction on the optical wheel

or press the trigger onto which you wish to place your function.

Lit up green

Your “MANUAL PRESET” is now enabled and up to date

(with your programming applied to the optical wheel or triggers)

SWITCHING BUTTONS/MINI-STICKS/D-PAD

All progressive buttons (on PS2 and PS3) or digital buttons (on PC), as well as directions of the mini-

sticks and of the D-Pad can be switched using the MAPPING button (7).

• Examples of possible applications:

- Switch buttons between themselves

- Switch the 2 mini-sticks

(in this case, you will to have to map the 4 directions of the first mini-stick to the 4 directions of the

second mini-stick)

- Switch the D-Pad with a mini-stick

(in this case, you will have to map the 4 D-Pad directions to the 4 directions of the mini-stick in

question).

• Procedure for switching buttons, mini-sticks and D-Pad

- Does not work for the triggers.

- Works for the optical wheel but only on PC and in “7 axes” mode.

Steps Action

PRESET button

color

1 Enable “MANUAL PRESET” (8) by pressing the button. Lit up green

2 Press and release the MAPPING button (7). Lit up red

3 Press and release the button or direction to switch. Flashes red

4

Press and release the button or direction onto which you wish to

place your function.

Lit up green

Your “MANUAL PRESET” is now enabled and up to date (with the 2 functions switched).

9/14

EEPROM MEMORY

• Your gamepad features an internal chip which saves all of your “MANUAL PRESET” programming

(even when the gamepad is switched off or disconnected for a long period of time).

• You can save a different “MANUAL PRESET” for each platform used:

PlayStation® 1, PlayStation® 2, PlayStation® 3, PC 4 Axes and PC 7 Axes

TO ERASE YOUR “MANUAL PRESET”

Action

PRESET button

color

1 Enable your “MANUAL PRESET” (8). Lit up green

2 Press and hold the MAPPING button (7) for 2 seconds.

Flashes green 2

seconds

Your “MANUAL PRESET” is now clear (and once again identical to the “AUTOMATIC PRESET”).

RETURNING TO “FACTORY SETTINGS”

You can erase all of your programming or settings:

Steps Action MAPPING button color

1

Press the MAPPING + SELECT + START buttons

simultaneously

Flashes blue 5 seconds

All of your “MANUAL PRESETS” (= PC + PS2 + PS3) or settings are now clear.

Note: this procedure will completely restart your gamepad

(on PC, we therefore recommend that you do this outside of games).

POSSIBLE USES IN GAMES

The optical wheel (thanks to its technology and degree of rotation greater than that of any mini-stick) offers

unparalleled precision and stability in all types of games: racing (ultra-precise steering), flying (rudder),

action and FPS (progressive zoom), sports (measured shot, strength of hit), etc.

The triggers (thanks to their progressive action and range of mechanical travel greater than that of any

button) offer extremely precise control in all types of games: racing (progressive and independent

acceleration and braking, handbrake), action and FPS (rate of fire, lateral movement), sports (measured

pass or shot, strength of hit or jump, running speed), etc.

SOME EXAMPLES AND TIPS:

- There are numerous configuration possibilities, depending on the game you are playing.

- In certain games (racing type), do not hesitate to test out the 2 sensitivity modes for your optical wheel

(Normal or High) in order to optimize its precision and responsiveness.

10/14

DIFFERENT EXAMPLES ACCORDING TO TYPE OF GAME

Action/Adventure (“Car” mode) Action/Adventure (“On foot” mode)

Sports (“Ball game” type) Sports (“Golf” type)

Car racing (“Simulation” type) Car racing (“Arcade/Rally” type)

Flying (“Simulation” type) Flying (“Arcade/Action” type)

11/14

USING MORE THAN ONE “Run’N’ Drive Wireless” GAMEPAD AT THE SAME TIME

(in Multiplayer mode)

You can use up to 4 “Run’N’ Drive Wireless” gamepads at the same time (in multiplayer mode).

Channel detection is carried out automatically

In case of error or to force the connection: press the CONNECT button on the receiver

and simultaneously press the L2 + R2 + MAPPING buttons on your gamepad.

TROUBLESHOOTING AND WARNINGS

• My gamepad doesn’t function correctly or seems improperly calibrated:

- In the event of malfunction due to electrostatic emission, exit the game, switch off your gamepad and

disconnect the receiver from your console or your PC.

To play again, reconnect the receiver, switch your gamepad back on and start the game again.

- Never move the mini-sticks, the optical wheel or the triggers when connecting your gamepad (to avoid

any calibration problems).

- On PC, if the game does not accept “7 axes” mode (undesired effects), switch your gamepad to “4 axes”

mode (the standard gamepad mode).

• I can’t configure my gamepad in a game:

- In your game’s “Options / Controller / Gamepad” menu: select the most appropriate configuration.

- Please refer to your game’s user manual or online help for more information.

- You can also use your gamepad’s “programming” function to resolve this type of problem.

• On PC or PS3, my gamepad doesn’t function correctly:

- Exit your game, disconnect your gamepad, verify that the “PC/PS3” USB selector (11) is in the proper

position, then reconnect everything.

• The MAPPING LED flashes slowly and continuously:

- Please change batteries.

When you’re done using your gamepad, we recommend that you always set the gamepad’s

POWER ON/OFF switch (15) to the OFF position (to save your batteries).

12/14

TECHNICAL SUPPORT

If you encounter a problem with your product, please go to http://ts.thrustmaster.com and click Technical Support. From

there you will be able to access various utilities (Frequently Asked Questions (FAQ), the latest versions of drivers and

software) that may help to resolve your problem. If the problem persists, you can contact the Thrustmaster products

technical support service (“Technical Support”):

By email:

In order to take advantage of technical support by email, you must first register online. The information you provide will help

the agents to resolve your problem more quickly. Click Registration on the left-hand side of the Technical Support page and

follow the on-screen instructions. If you have already registered, fill in the Username and Password fields and then click

Login.

By telephone:

United

Kingdom

08450800942

Charges at local

rate

Monday to Friday from Noon to 4pm and 5pm to 10pm

Saturday from 9am to Noon and 1pm to 7pm

Sunday from 9am to Noon and 1pm to 4pm

United

States

1-866-889-5036

Free

Monday to Friday from 7am to 11am and from Noon to 5pm

Saturday and Sunday from 7am to Noon

(Eastern Standard Time)

Canada

1-866-889-2181

Free

Monday to Friday from 7am to 11am and from Noon to 5pm

Saturday and Sunday from 7am to Noon

(Eastern Standard Time)

Denmark

80887690

Free

Monday to Friday from 1pm to 5pm and 6pm to 11pm (English)

Saturday from 9am to 1pm and 2pm to 8pm

Sunday from 10am to 1pm and 2pm to 5pm

Sweden

0200884567

Free

Monday to Friday from 1pm to 5pm and 6pm to 11pm (English)

Saturday from 9am to 1pm and 2pm to 8pm

Sunday from 10am to 1pm and 2pm to 5pm

Finland

0800 913060

Free

Monday to Friday from 2pm to 6pm and 7pm to Midnight (English)

Saturday from 10am to 2pm and 3pm to 9pm

Sunday from 11am to 2pm and 3pm to 6pm

13/14

WARRANTY INFORMATION

Worldwide, Guillemot Corporation S.A. (“Guillemot”) warrants to the consumer that this Thrustmaster product will

be free from material defects and manufacturing flaws for a period of two (2) years from the original date of

purchase. Should the product appear to be defective during the warranty period, immediately contact Technical

Support, who will indicate the procedure to follow. If the defect is confirmed, the product must be returned to its

place of purchase (or any other location indicated by Technical Support).

Within the context of this warranty, the consumer’s defective product will, at Technical Support’s option, be either

repaired or replaced. Where authorized by applicable law, the full liability of Guillemot and its subsidiaries

(including for indirect damages) is limited to the repair or replacement of the Thrustmaster product. The

consumer’s legal rights with respect to legislation applicable to the sale of consumer goods are not affected by this

warranty.

This warranty shall not apply: (1) if the product has been modified, opened, altered, or has suffered damage as a

result of inappropriate or abusive use, negligence, an accident, normal wear, or any other cause not related to a

material defect or manufacturing flaw; (2) in the event of failure to comply with the instructions provided by

Technical Support; (3) to software not published by Guillemot, said software being subject to a specific warranty

provided by its publisher.

Additional warranty provisions

In the United States of America and in Canada, this warranty is limited to the product’s internal mechanism and

external housing. Any applicable implied warranties, including warranties of merchantability and fitness for a

particular purpose, are hereby limited to two (2) years from the date of purchase and are subject to the conditions

set forth in this limited warranty. In no event shall Guillemot Corporation S.A. or its affiliates be liable for

consequential or incidental damage resulting from the breach of any express or implied warranties. Some

States/Provinces do not allow limitation on how long an implied warranty lasts or exclusion or limitation of

incidental/consequential damages, so the above limitation may not apply to you. This warranty gives you specific

legal rights, and you may also have other legal rights which vary from State to State or Province to Province.

COPYRIGHT

S.A. PlayStation® is a registered trademark of Sony Computer Entertainment, Inc. Windows® and Windows® XP are

registered trademarks of Microsoft Corporation in the United States and/or in other countries. Pentium® is a registered

trademark of Intel Corporation. All other trademarks and brand names are hereby acknowledged and are the property of

their respective owners. Illustrations not binding. Contents, designs and specifications are subject to change without notice

and may vary from one country to another. Made in China.

14/14

ENVIRONMENTAL PROTECTION RECOMMENDATION

At the end of its working life, this product should not be disposed of with standard household waste,

but rather dropped off at a collection point for the disposal of Waste Electrical and Electronic

Equipment (WEEE) for recycling.

This is confirmed by the symbol found on the product, user manual or packaging.

Depending on their characteristics, the materials may be recycled. Through recycling and other forms

of processing Waste Electrical and Electronic Equipment, you can make a significant contribution

towards helping to protect the environment.

Please contact your local authorities for information on the collection point nearest you.

FAQs, tips and drivers available at www.thrustmaster.com

1/14

Manuel de l'utilisateur

CARACTÉRISTIQUES TECHNIQUES

1. 2 moteurs de vibrations indépendants

(pour Playstation® 2)

2. 2 sticks analogiques progressifs

3. Croix digitale

4. Roue optique progressive

5. 2 Gâchettes progressives

6. Bouton Led HOME pour Playstation®3

et MODE pour PC

7. Bouton Led MAPPING (pour programmer

et indiquer l’état de la Connexion)

8. Bouton Led PRESET

(pour choisir son programme)

9. Boutons d’actions

10. Connecteur « USB » PC et Playstation® 3

11. Sélecteur USB « PC » ou « PS3 »

12. Bouton Led CONNECT du récepteur

13. Connecteur « Gameport » Playstation® 2

14. Compartiment à piles

15. Interrupteur POWER ON/OFF

16. Interrupteur MOTORS ON/OFF

2/14

TABLEAU DES « MODES » SUPPORTES

Support MODE

Couleur du bouton

HOME (6)

PLAYSTATION®

1

« PS1 » ETEINT

PLAYSTATION® 2 « PS2 » ROUGE

PLAYSTATION® 3 « PS3 » ROUGE

« 4 AXES » VERT

PC

« 6 AXES » ROUGE

INSTALLATION DES PILES

Installez 2 piles de type LR03 / AAA dans le compartiment à piles situé à l’arrière de la manette (14).

GENERALITES

• Bouton INTERUPTEUR POWER (15)

- Position OFF = la manette est éteinte (et n’use pas les piles).

- Position ON = la manette est allumé.

• Bouton INTERUPTEUR MOTORS (16)

- Position OFF = le mode vibration est désactivé (économise les piles).

- Position ON = le mode vibration est activé (consomme davantage d'énergie).

• Bouton Sélecteur USB « PC / PS3 » (11)

Doit toujours être positionné sur la bonne position avant de connecter l’USB de votre récepteur.

• Leds bleus MAPPING (7) et CONNECT (12)

- Les 2 Leds sont allumés = connexion établie entre la manette et le récepteur.

- Les 2 Leds clignotent rapidement = pas de connexion entre la manette et le récepteur.

- La Led Mapping est éteinte = la manette est en mode veille ou éteinte.

- La Led Mapping clignote lentement en continu = il convient de changer les piles.

LA CONNEXION ENTRE LA MANETTE ET LE RECEPTEUR S’EFFECTUE AUTOMATIQUEMENT

En cas d’échec pour forcer la connexion : appuyez sur le bouton CONNECT du récepteur

puis simultanément sur les boutons L2 + R2 + MAPPING de votre manette.

• MODE VEILLE

La manette s'éteint automatiquement :

- Après 5 minutes d'inactivité

- Après 5 secondes en cas d’échec ou de perte de connexion.

Pour réveiller votre manette : appuyez sur START ou utilisez l’interrupteur POWER ON/OFF (15).

3/14

PLAYSTATION® 3

INSTALLATION SUR « PLAYSTATION® 3 »

1. Mettez le sélecteur USB de votre récepteur (11) en position « PS3 ».

2. Branchez le connecteur USB sur le port USB n°1 de la console.

3. Allumez votre console.

4. Allumez votre manette à l’aide de l’interrupteur POWER ON (13)

5. Une fois la connexion établie : lancez le jeu.

Vous êtes maintenant prêt à jouer !

MODE « PLAYSTATION® 3 »

CONFIGURATION DU « PRESET AUTOMATIQUE » - PLAYSTATION® 3

Mode « PS3 » Bouton HOME ROUGE

Ici :

• « Roue optique » associée à la direction

«Gauche/Droite» du mini-stick gauche

• « Gâchette Droite » associée au

bouton progressif « R2 »

• « Gâchette Gauche » associée au

bouton progressif « L2 »

UTILISATION DU BOUTON « HOME » (6)

Le bouton « Home » de votre manette vous permettra de quitter vos jeux, d’accéder aux menus et

d’éteindre directement votre système PlayStation®3

REMARQUES IMPORTANTES SUR « PLAYSTATION® 3 »

- Le sélecteur USB de votre récepteur (11) doit toujours être positionné sur « PS3 » avant de le connecter

- En mode « 1 Joueur » si votre manette officielle est allumée il est alors nécessaire de basculer celle-ci en

« port manette 2 » afin que votre manette « Run’N’ Drive» soit fonctionnelle.

- Sur « Playstation® 3 », la manette « Run’N’ Drive » n’est compatible qu’avec les jeux « Playstation® 3 »

(et ne fonctionnera pas avec les jeux « Playstation® 2 ») et ne possède pas de détecteur de mouvement

4/14

PLAYSTATION® 2

INSTALLATION SUR « PLAYSTATION® 2 »

1. Branchez le connecteur Gameport PS2 (13) du récepteur sur le port n°1 de la console.

2. Allumez votre console

3. Allumez votre manette à l’aide de l’interrupteur POWER ON (15)

4. Une fois la connexion établie : lancez le jeu.

Vous êtes maintenant prêt à jouer !

MODE « PLAYSTATION® 2 »

CONFIGURATION DU « PRESET AUTOMATIQUE » - PLAYSTATION® 2

Mode « PS2 » Bouton HOME ROUGE

Ici :

• « Roue optique » associée à la direction

« Gauche/Droite » du mini-stick gauche.

• « Gâchette Droite » associée au

bouton progressif « Croix »

• « Gâchette Gauche » associée au

bouton progressif « Carré »

REMARQUES IMPORTANTES SUR « PLAYSTATION® 2 »

Ne jamais connecter le câble USB (10) sur votre Playstation® 2 (pour éviter tout risque d’endommagement de

votre manette ou de votre console)

5/14

PC

INSTALLATION SUR PC

1. Mettre le sélecteur USB de votre récepteur (11) en position « PC »

2. Reliez le connecteur USB du récepteur à l'un des ports USB de votre unité centrale. Windows® XP ou

Vista détectera automatiquement le nouveau périphérique.

3. Allumez votre manette à l’aide de l’interrupteur POWER ON (15).

4. Sélectionnez Démarrer/Paramètres/Panneau de configuration puis double-cliquez sur

Contrôleurs de jeu

La boîte de dialogue Contrôleurs de jeu affichera le nom de la manette avec l'état OK.

5. Dans le Control Panel, cliquez sur Propriétés pour tester et visualiser les boutons, le D-Pad, les mini-

sticks, les gâchettes et la roue optique.

Vous êtes maintenant prêt à jouer !

REMARQUES IMPORTANTES SUR « PC »

- Le sélecteur USB du votre récepteur (11) doit toujours être positionné sur « PC » avant le connecter

- Un logiciel de « Programmation Avancée » pour PC est également disponible en téléchargement sur notre

site Internet à cette adresse :

http://ts.thrustmaster.com/

SELECTION DES « AXES » SUR PC

• Sélection des axes par « Software » :

Après avoir installé le « Logiciel de Programmation Avancée », allez dans la page 1 du Control

Panel, cliquez sur le nombre d’axes désiré puis sur Ok.

• Sélection des axes par « Hardware » :

Pressez le bouton HOME (6) pour sélectionner le nombre d’axes actifs.

La page charge ...

Thrustmaster RUN'N' DRIVE WIRELESS 3-IN-1 Le manuel du propriétaire

Thrustmaster RUN'N' DRIVE WIRELESS 3-IN-1 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents