Gallagher FenceAlarm Instructions Manual

Taper
Instructions Manual
0
1
1. Introduction
Thank you for purchasing this Gallagher FenceAlarm.
Gallagher, as a world leader in electric fencing, is committed to providing
leading products. The SMS FenceAlarm is a unique plug and play security
for your fence. The FenceAlarm warns you through an SMS message on
your mobile phone if there is insufficient voltage (e.g. caused by
vegetation) or if the fence line is interrupted (e.g. caused by opening a
gate).
If for any reason you are not happy with your purchase, please return it to
your dealer within 30 days of purchase. If you have any questions
regarding this product please email us: info.uk@gallaghereurope.com, or
contact the store where you purchased this Gallagher product.
Before you start the installation it is important that the installation
instructions are studied carefully.
2. Important information
Switch off the electric fence before mounting or opening up the
FenceAlarm.
Do not leave dead batteries in the FenceAlarm. Dead batteries can leak
and cause damage to the FenceAlarm.
Make sure there is always enough call credits fitted on the SIM card of
the FenceAlarm and check this on a regular basis.
3. Preparing for use
The FenceAlarm only works if a prepaid SIM card with enough credits has
been fitted. A SIM card with a subscription can also be used. To fit the SIM
card, proceed as follows:
1. Unscrew the 4 screws of the cover.
2. Place a SIM card in the SIM card slot of the FenceAlarm with the chip
facing downwards. Make sure the PIN code is set at “0000” (default
2
setting) or disabled. The SIM card lies on the cover behind the rubber
inlay.
3. Fit 3 Alkaline (non-rechargeable AA) batteries in the battery holder.
4. Screw the cover back on tight. Make sure there is no dust or dirt
between the rubber seal and the cover to prevent contact with moist.
4. Enter a telephone number
To have the FenceAlarm communicating with a mobile phone you can
enter a mobile phone number to receive SMS fence messages. To enter a
telephone number in the FenceAlarm you have to send an SMS text
message.
SIM
3
1a. Type an SMS message with the text M1:+44 and your mobile
telephone number. Do not send this message yet!
Note:
+44 is the country code for the UK.
Please use the correct country code if
outside of the UK.
The M must be in CAPITALS.
The “0” at the start of your mobile
phone number should be left out.
Everything must be typed without
spaces, there must be no spaces
between any characters.
1b. Changing settings, Type an SMS message with the requested changes
(paragraph 10) Do not send this message yet!
2. Switch the magnet to OFF for at least 10 seconds (the lamp has to
go out).
Say your own mobile
phone number is
07956111222. The
number of the SIM
card fitted in the
FenceAlarm is
07956111333.
Now you should send
an SMS text message
with the text:
M1:+447956222333
(M in CAPITALS) to
07956111333
(FenceAlarm).
(FenceAlarm).
4
3. Switch the magnet slowly back and forth between OFF
and ON a few times; continue until the lamp flashes
blue once. Now leave the magnet switched to ON.
4. Wait until the Gallagher FenceAlarm lamp flashes alternately blue
and green. The Gallagher FenceAlarm is now connected with the
GSM network. You now have a maximum of 2 minutes to carry out
step 5.
If the lamp stops flashing blue and green, then you have to carry out
steps 2 to 4 again.
5. Send the SMS text message to the number of the SIM card in the
Gallagher FenceAlarm.
6. After a few minutes you will receive a status message. This status
message is explained later on in this guide, but in the status
message you should see "M1:" followed by your telephone
number.
5. Installation of the FenceAlarm
For optimal operation, the Gallagher FenceAlarm must be located as far
away as possible from the energiser. The length of the fencing to the right
of the FenceAlarm should preferably be the same as the length of the
fencing to the left.
The fencing must be disconnected in both directions at the FenceAlarm.
You can do this by attaching the fencing from both directions to 2 separate
insulators.
Connect the red clamp of the FenceAlarm to the left/right part and
connect the yellow clamp to the other part of the fence line.
The green clamp needs to be connected to an earth peg (not included).
5
6. Starting up
To activate the FenceAlarm switch the magnet from OFF to ON.
The FenceAlarm is then automatically activated. It may take a few minutes
for it to start up. As soon as the FenceAlarm is activated, the lamp will
flash green once every 12 seconds. In order to save energy, the lamp does
not burn too brightly, and is therefore hard to see in daylight. You will also
get a status SMS message with the current measurement values and
settings.
6
7. Operation of the FenceAlarm
The Gallagher FenceAlarm provides you with details about the fencing
voltage measured in two directions. It also warns you if at any time the
fencing voltage falls below the minimum required level (for example, if
wild plants have caused a breakdown in the operation of the fencing). As
long as the situation has not been rectified, you will receive regular
reminder SMS messages.
The Gallagher FenceAlarm will send an alert immediately if the fencing
voltage disappears completely in either direction. For example, if the wires
are cut or disconnected in any way whatsoever.
The Gallagher FenceAlarm also measures the interval between 2 pulses,
and sends this interval measurement in the Status SMS message.
The Gallagher FenceAlarm will send a Status SMS message at an adjustable
interval (standard 1x per week) to keep you informed about the status and
operation of the fencing. This is the “Heartbeat SMS”.
The FenceAlarm also has an internal timer which indicates if the power
pack of the energizer needs to be recharged. This timer can be configured
so you are sent an SMS message after a certain amount of time has
elapsed.
7
8. Read received SMS messages
The FenceAlarm informs you about the current status and sends alarms via
SMS text messages.
A STATUS SMS message will look something like this:
GSM STATUS
GSM STATUS: The following data concerns the FenceAlarm
Batt 100%
Battery capacity is still 100%
Signal 48%
GSM signal strength is 48%
SMSno:5
A total of 5 SMS messages have been sent
M1:+31611112222
Telephone number the SMS is sent to
Fence STATUS
Fence STATUS: The following data concerns the fencing
Batt 1 days
Energiser power pack consumption = 1 day
RED: 7.1kV
Voltage measured on the red wire (RED) is 7.1kV
YEL: 7.2kV
Voltage measured on the yellow wire (YEL) is 7.2kV
Puls> 1.2sec
Measured interval between 2 pulses.
8
If something is wrong with your fencing, you will receive a Fence Alarm
SMS. This will have the following format.
ALARM
GSM STATUS: The following data concerns the FenceAlarm
Batt 100%
Battery capacity is still 100%
Signal 48%
GSM signal strength is 48%
SMSno:5
A total of 5 SMS messages have been sent
FENCE
Fence STATUS: The following data concerns the fencing
Batt 1 days
Energiser power pack consumption = 1 day
RED: 2.3kV
Voltage measured on the red wire (RED) is 2.3kV (too low!)
YEL: 7.2kV
Voltage measured on the yellow wire (YEL) is 7.2kV
Puls> 1.2sec
Measured interval between 2 pulses.
9
If you change the settings, you will receive a Settings SMS. This will have
the following format.
9. Meaning of abbreviations
The FenceAlarm uses abbreviations in order to carry out commands
quickly and correctly, and to display measurement values in the SMS
messages. It is important that you know what the commands mean. Below
you can find the abbreviations of the status SMS message.
M1:+31611112222
Telephone number the SMS is sent to
PG:2 V37
Software version.
GV:32
Perimeter Voltage is 3.2kV
DT:30
The day timer is set at 30 days
TM:006
Reminder in the event of an Alarm every 6 hours
DG:168
A status message once every 168 hours (once per week)
TP: 214415040310
Current time and date (see explanation on page 13)
10
GSM STATUS
Batt 100%
The battery capacity is still 100%. When this value
reaches 20% it is time to change the batteries.
Signal 48%
GSM signal strength is 48%. The GSM signal strength
must not be less than 15%, otherwise there is a risk
the device will not be able to make a connection with
the network. In that case you would need to use a
SIM card of a different provider.
SMSno:5
A total of 5 SMS messages have been sent. The
FenceAlarm logs the number of SMS messages sent
for you. This will help you monitor the consumption
of the call credits. Check the balance and validity
period of the call credits now and again to ensure the
device continues to operate correctly.
M1:+31611112222
Telephone number the SMS is sent to by the
FenceAlarm. This should be the mobile telephone
number of the fence owner. Tip: always use the
country code for the mobile phone number
Fence STATUS
Batt 1 days
Energiser power pack consumption = 1 day. When
the FenceAlarm is activated, the day timer starts
counting from 0. This means you know how long the
power pack has already been in use, and based on
the capacity of the power pack and the energy
consumption of your energiser, you can calculate
how many days are left before the power pack has to
be replaced/recharged. This means that when you fit
a new power pack to your energiser, you have to
turn the FenceAlarm off and on again in order to
reset the day timer to 0.
RED: 7.1kV
Voltage measured on the red wire (RED) is 7.1kV. The
voltage measured on both wires is rounded off to a
10th of a kilovolt (i.e., in multiples of 100V).
YEL: 7.2kV
Voltage measured on the yellow wire (YEL) is 7.2kV
The voltage measured on both wires is rounded off
11
to a 10th of a kilovolt (i.e., in multiples of 100V)
Puls> 1.2sec
Measured interval between 2 pulses. This interval is
measured for you. Some energisers increase the
pulse interval when the power pack level is low. If
this happens, you know the power pack of the
energiser needs to be replaced.
If you use your own mobile telephone to change the settings of the
FenceAlarm you will be sent a settings SMS message.
SETTINGS
M1:+31611112222
Telephone number the SMS is sent to by the
FenceAlarm. This should be the mobile telephone
number of the fence owner. Tip: always use the
country code for the mobile phone number.
V37
Software version. This tells you the software version
installed on the FenceAlarm.
GV:32
Perimeter Voltage is 3.2kV.This is the minimal value
that will activate the FenceAlarm in sending a
FenceAlarm SMS message.
DT:30
The day timer is set at 30 days. You can set the time
that the battery of your energiser will last. The
FenceAlarm will send a FenceAlarm SMS message
after 30 days.
TM:006
TM is short for time. The alarm will be repeated
every 6 hours. If you receive an alarm message, the
FenceAlarm will continue sending (reminder)
messages to you at a set interval.
DG:168
DG is short for daily message. A status message will
be sent once every 168 hours (once per week). At set
intervals the FenceAlarm will send you a status SMS
message to keep you informed about the current
status of your fence. In this way the FenceAlarm lets
you know that everything is still working properly.
The standard setting is for the SMS to be sent at
20:00 hours. However, you still have to set the time
12
for this.
TP:214415040310
Current time and date. This is the time and date the
message was sent. The time and date in this example
is 21 hours, 44 minutes, 15 seconds on the 04 day of
the 03 month of the year 2010.
10. Changing the settings of the FenceAlarm
You can only change settings when the internal GSM of the FenceAlarm is
active. It is only active for a short while after an SMS message, or if you
switch the FenceAlarm to programming mode. See paragraph 4 1b
changing settings”.
Set the time
When you change the date and time, please take into account that the
FenceAlarm operates with a 24 hours clock. When you, for instance, want
to set 1 o’clock in the afternoon on 5 April in 2010 (13:00:00 05/04/2010),
then you send an SMS message to the FenceAlarm: TP:130000050410.
Set the perimeter voltage
The perimeter voltage is the minimal value that will activate the
FenceAlarm in sending a FenceAlarm SMS message. If you want to set the
perimeter voltage in e.g. 4.0kV, send an SMS message to the FenceAlarm
with: GV:40. This value can be set between 2.0kV and 9.9kV.
Set the day timer
This feature is a Handy tool for portable energisers to keep track of the
durability of batteries. The day timer counts the days that the battery will
operate. So, if your energiser operates about 40 days on the used battery
then you send the following SMS message to the FenceAlarm: DT:40. This
value can be set between 00 and 00 days. If the battery voltage becomes
too low, then you will be notified through an SMS message as well.
13
Set the interval of status SMS messages
At set intervals the FenceAlarm will send you a status SMS message to
keep you informed about the current status of your fence. In this way the
FenceAlarm lets you know that everything is still working properly. The
standard setting is for the SMS to be sent at 20:00 hours. However, you
still have to set the time for this. If you wish to receive a status SMS
message, send an SMS message with: DG:48 to the FenceAlarm and you
will receive every 2 days at 8 o’clock at night an update on the status of
your fence. You can set this value between 00 and 250 hours.
Set the interval of FenceAlarm SMS messages
If you receive an alarm message, the FenceAlarm will continue sending
(reminder) messages to you at a set interval. You can change this interval
with this setting. You can set this value between 000 and 250 hours. The
default setting for this value is 6 hours. (TM:006). This means you will
receive a reminder once every 6 hours. If you want to change this interval
to 24 hours, for example, then you SMS TM:024 to the FenceAlarm.
Resetting the FenceAlarm
Switch the magnet to OFF for at least 10 seconds (the lamp has to go
out).To activate the Gallagher FenceAlarm switch the magnet from OFF to
ON. It may take a few minutes for it to start up.
14
1. Inleiding
Hartelijk dank voor de aanschaf van de Gallagher FenceAlarm.
Gallagher, wereldwijd marktleider in elektrische afrasteringen, wil
producten van topkwaliteit leveren. De SMS FenceAlarm is een unieke plug
and play beveiliging van uw afrastering. De FenceAlarm waarschuwt u op
uw mobiele telefoon per SMS bij onvoldoende voltage (door bijv.
begroeiing) of bij onderbreking van het raster (door bijv. het openen van
een poort).
Indien u om enige reden niet tevreden bent met uw aankoop, aarzel dan
niet om dit apparaat binnen 30 dagen na aankoop terug te sturen naar de
winkel waar u het aangeschaft heeft. Indien u vragen heeft betreffende dit
product, gelieve ons dan een e-mail te sturen:
info.nl@gallaghereurope.com, of neem contact op met de winkel waar u
dit Gallagher-product heeft aangeschaft.
Lees voor een goede werking van de FenceAlarm deze gebruiksaanwijzing
goed door.
2. Belangrijke informatie
Schakel eerst het schrikdraadapparaat uit alvorens u de FenceAlarm
monteert of openschroeft.
Laat lege batterijen niet in de FenceAlarm zitten. Lege batterijen
kunnen gaan lekken en schade veroorzaken aan de FenceAlarm.
Zorg er voor dat er altijd voldoende beltegoed op de SIM-kaart van de
FenceAlarm staat en controleer dit regelmatig.
3. Gereedmaken voor gebruik
De FenceAlarm werkt alleen wanneer er een prepaid SIM-kaart geplaatst is
met voldoende beltegoed. Een SIM-kaart met abonnement is ook mogelijk.
Zorg in beide gevallen dat de voicemail is uitgeschakeld en dat de pincode
op “0000” staat (standaard instelling) of uitgeschakeld is.
15
Volg voor het plaatsen van de SIM-kaart de volgende stappen:
1. Schroef de 4 schroeven van het deksel open.
2. Plaats een SIM-kaart in de SIM-kaarthouder van de FenceAlarm met de
chip naar beneden. Zorg dat de SIM-kaart goed klemt tussen de
houder. De SIM-kaart rust op het deksel voorbij het rubber.
3. Plaats drie alkaline (niet-oplaadbare AA) batterijen in de
batterijhouder.
4. Schroef het kastje goed dicht. Let op dat er geen vuil o.i.d. tussen het
afdichtingrubber en het deksel zit zodat het kastje goed afgesloten is
voor vocht.
SIM
16
4. Telefoonnummer instellen/Instellingen wijzigen
Om de FenceAlarm te laten communiceren met een mobiele telefoon
dient u hiervoor een mobiel telefoonnummer in te voeren voor het
ontvangen van de SMS-rasterberichten. Het instellen van het
telefoonummer in De FenceAlarm gebeurt door het versturen van een
SMS-bericht.
1a. Typ een SMS-berichtje met de tekst M1:+31 gevolgd door uw mobiele
telefoonnummer. Verstuur deze nog
niet!
Let op:
+31 is de landcode van Nederland.
Gebruikt u een Duits nummer,
vervang dan +31 door +49.
De M moet met een
HOOFDLETTER.
De “0” van het 06-nummer
weglaten achter de landcode.
Alles moet aan elkaar getypt
worden, er mag geen spatie tussen
zitten
1b. Instellingen wijzigen/ resetten, Type een SMS-berichtje met de
gewenste instellingen (zie hoofdstuk 10). Verstuur deze nog niet!
2. Plaats de magneet minimaal
10 seconden op OFF, het
lampje mag nu niet meer
branden.
Stel dat uw eigen
mobiele nummer
0611112222 is. Stel
dat het nummer van
de SIM-kaart in het
FenceAlarm
0633334444 is.
Nu dient u een SMS-
bericht te versturen
met de tekst
M1:+31611112222 (M
in HOOFDLETTER) naar
0633334444
(FenceAlarm).
17
3. Schuif met de magneet een paar keer rustig heen en weer van OFF
naar ON. Ga hiermee door totdat het lampje één keer blauw oplicht.
Laat nu de magneet op ON staan.
4. Wacht tot De FenceAlarm afwisselend blauw en groen oplicht. De
FenceAlarm heeft nu verbinding met het GSM netwerk. U heeft nu
maximaal 2 minuten de tijd om de volgende stap uit te voeren.
Knippert het lampje niet meer afwisselend blauw en groen, dan
dient u stap 2 tot en met 4 opnieuw uit te voeren.
5. Verstuur vervolgens het SMS-berichtje uit stap 1a of 1b naar het
nummer van de SIM-kaart in de FenceAlarm.
6. Na enkele minuten ontvangt u een statusbericht. De inhoud van dit
statusbericht wordt verderop in deze handleiding nader toegelicht.
Vervolgens kunt u de FenceAlarm uitzetten, het telefoonnummer is nu
opgeslagen.
5. Aansluiten op het raster
Voor een goede werking dient de FenceAlarm fysiek zo ver mogelijk van
het schrikdraadapparaat verwijderd te zijn. Bij voorkeur dient de
FenceAlarm halverwege in het raster geplaatst te worden, waarbij de
hoeveelheid raster vanaf links ongeveer dezelfde lengte heeft als vanaf
rechts.
Ter hoogte van de FenceAlarm moet het raster uit beide richtingen
worden ontkoppelt. Dit kunt u doen door het raster uit beide richtingen
naar twee aparte isolatoren te leiden.
Sluit vervolgens op het ene ontkoppelde raster de rode klem aan en op het
andere ontkoppelde raster de gele klem.
De groene klem dient aangesloten te worden op een aardpen (niet
bijgeleverd).
18
6. Ingebruikname
Om de FenceAlarm aan te zetten schuift u de magneet van OFF naar ON.
De FenceAlarm wordt vervolgens automatisch actief.
Het opstarten kan enkele minuten duren. Zodra de FenceAlarm actief is,
zal het lampje iedere 12 seconden één keer groen oplichten. Dit is overdag
moeilijk te zien in verband met energiebesparing. U zult tevens een SMS-
statusbericht krijgen met actuele meetwaarden en instellingen.
19
7. Werking van de FenceAlarm
De FenceAlarm biedt u inzicht in de actuele rasterspanning gemeten vanuit
twee richtingen. Tevens wordt u gewaarschuwd wanneer de
rasterspanning al enige tijd onder het minimum is (bijvoorbeeld wanneer
wildgroei de werking van het raster belemmert). U ontvangt, zolang de
situatie niet hersteld is, regelmatig een herinnerings-SMS genaamd “Still
Alarm”.
De FenceAlarm komt direct in actie wanneer de rasterspanning uit een van
de richtingen helemaal verdwijnt, bijvoorbeeld wanneer er draden worden
doorgeknipt of op een andere wijze worden onderbroken.
De FenceAlarm meet de periodetijd tussen twee pulsen en stuurt deze
gemeten periodetijd mee in de status-SMS. Hiermee kunt u zien of het
apparaat in de batterijspaarstand staat, wat aangeeft dat u de batterij of
accu van het mobiele apparaat moet vervangen.
De FenceAlarm stuurt tevens op een instelbare interval (standaard één
keer per week) een SMS-statusbericht om u op de hoogte te houden van
de toestand en werking van het raster.
De FenceAlarm heeft een geïntegreerde dagenteller die aangeeft wanneer
de accu van een mobiel schrikdraadapparaat opgeladen dient te worden.
Deze timer is instelbaar en wanneer de tijd verstrijkt ontvangt u een SMS.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67

Gallagher FenceAlarm Instructions Manual

Taper
Instructions Manual

dans d''autres langues