Gallagher FenceAlarm Instructions Manual

0

1

1. Introduction

Thank you for purchasing this Gallagher FenceAlarm.

Gallagher, as a world leader in electric fencing, is committed to providing

leading products. The SMS FenceAlarm is a unique plug and play security

for your fence. The FenceAlarm warns you through an SMS message on

your mobile phone if there is insufficient voltage (e.g. caused by

vegetation) or if the fence line is interrupted (e.g. caused by opening a

gate).

If for any reason you are not happy with your purchase, please return it to

your dealer within 30 days of purchase. If you have any questions

regarding this product please email us: info.uk@gallaghereurope.com, or

contact the store where you purchased this Gallagher product.

Before you start the installation it is important that the installation

instructions are studied carefully.

2. Important information

 Switch off the electric fence before mounting or opening up the

FenceAlarm.

 Do not leave dead batteries in the FenceAlarm. Dead batteries can leak

and cause damage to the FenceAlarm.

 Make sure there is always enough call credits fitted on the SIM card of

the FenceAlarm and check this on a regular basis.

3. Preparing for use

The FenceAlarm only works if a prepaid SIM card with enough credits has

been fitted. A SIM card with a subscription can also be used. To fit the SIM

card, proceed as follows:

1. Unscrew the 4 screws of the cover.

2. Place a SIM card in the SIM card slot of the FenceAlarm with the chip

facing downwards. Make sure the PIN code is set at “0000” (default

2

setting) or disabled. The SIM card lies on the cover behind the rubber

inlay.

3. Fit 3 Alkaline (non-rechargeable AA) batteries in the battery holder.

4. Screw the cover back on tight. Make sure there is no dust or dirt

between the rubber seal and the cover to prevent contact with moist.

4. Enter a telephone number

To have the FenceAlarm communicating with a mobile phone you can

enter a mobile phone number to receive SMS fence messages. To enter a

telephone number in the FenceAlarm you have to send an SMS text

message.

SIM

3

1a. Type an SMS message with the text M1:+44 and your mobile

telephone number. Do not send this message yet!

Note:

 +44 is the country code for the UK.

Please use the correct country code if

outside of the UK.

 The M must be in CAPITALS.

 The “0” at the start of your mobile

phone number should be left out.

 Everything must be typed without

spaces, there must be no spaces

between any characters.

1b. Changing settings, Type an SMS message with the requested changes

(paragraph 10) Do not send this message yet!

2. Switch the magnet to OFF for at least 10 seconds (the lamp has to

go out).

Say your own mobile

phone number is

07956111222. The

number of the SIM

card fitted in the

FenceAlarm is

07956111333.

Now you should send

an SMS text message

with the text:

M1:+447956222333

(M in CAPITALS) to

07956111333

(FenceAlarm).

4

3. Switch the magnet slowly back and forth between OFF

and ON a few times; continue until the lamp flashes

blue once. Now leave the magnet switched to ON.

4. Wait until the Gallagher FenceAlarm lamp flashes alternately blue

and green. The Gallagher FenceAlarm is now connected with the

GSM network. You now have a maximum of 2 minutes to carry out

step 5.

If the lamp stops flashing blue and green, then you have to carry out

steps 2 to 4 again.

5. Send the SMS text message to the number of the SIM card in the

Gallagher FenceAlarm.

6. After a few minutes you will receive a status message. This status

message is explained later on in this guide, but in the status

message you should see "M1:" followed by your telephone

number.

5. Installation of the FenceAlarm

For optimal operation, the Gallagher FenceAlarm must be located as far

away as possible from the energiser. The length of the fencing to the right

of the FenceAlarm should preferably be the same as the length of the

fencing to the left.

The fencing must be disconnected in both directions at the FenceAlarm.

You can do this by attaching the fencing from both directions to 2 separate

insulators.

Connect the red clamp of the FenceAlarm to the left/right part and

connect the yellow clamp to the other part of the fence line.

The green clamp needs to be connected to an earth peg (not included).

5

6. Starting up

To activate the FenceAlarm switch the magnet from OFF to ON.

The FenceAlarm is then automatically activated. It may take a few minutes

for it to start up. As soon as the FenceAlarm is activated, the lamp will

flash green once every 12 seconds. In order to save energy, the lamp does

not burn too brightly, and is therefore hard to see in daylight. You will also

get a status SMS message with the current measurement values and

settings.

6

7. Operation of the FenceAlarm

The Gallagher FenceAlarm provides you with details about the fencing

voltage measured in two directions. It also warns you if at any time the

fencing voltage falls below the minimum required level (for example, if

wild plants have caused a breakdown in the operation of the fencing). As

long as the situation has not been rectified, you will receive regular

reminder SMS messages.

The Gallagher FenceAlarm will send an alert immediately if the fencing

voltage disappears completely in either direction. For example, if the wires

are cut or disconnected in any way whatsoever.

The Gallagher FenceAlarm also measures the interval between 2 pulses,

and sends this interval measurement in the Status SMS message.

The Gallagher FenceAlarm will send a Status SMS message at an adjustable

interval (standard 1x per week) to keep you informed about the status and

operation of the fencing. This is the “Heartbeat SMS”.

The FenceAlarm also has an internal timer which indicates if the power

pack of the energizer needs to be recharged. This timer can be configured

so you are sent an SMS message after a certain amount of time has

elapsed.

7

8. Read received SMS messages

The FenceAlarm informs you about the current status and sends alarms via

SMS text messages.

A STATUS SMS message will look something like this:

GSM STATUS

GSM STATUS: The following data concerns the FenceAlarm

Batt 100%

Battery capacity is still 100%

Signal 48%

 GSM signal strength is 48%

SMSno:5

 A total of 5 SMS messages have been sent

M1:+31611112222

 Telephone number the SMS is sent to

Fence STATUS

Fence STATUS: The following data concerns the fencing

Batt 1 days

 Energiser power pack consumption = 1 day

RED: 7.1kV

 Voltage measured on the red wire (RED) is 7.1kV

YEL: 7.2kV

 Voltage measured on the yellow wire (YEL) is 7.2kV

Puls> 1.2sec

 Measured interval between 2 pulses.

8

If something is wrong with your fencing, you will receive a Fence Alarm

SMS. This will have the following format.

ALARM

GSM STATUS: The following data concerns the FenceAlarm

Batt 100%

 Battery capacity is still 100%

Signal 48%

 GSM signal strength is 48%

SMSno:5

 A total of 5 SMS messages have been sent

FENCE

Fence STATUS: The following data concerns the fencing

Batt 1 days

 Energiser power pack consumption = 1 day

RED: 2.3kV

 Voltage measured on the red wire (RED) is 2.3kV (too low!)

YEL: 7.2kV

 Voltage measured on the yellow wire (YEL) is 7.2kV

Puls> 1.2sec

 Measured interval between 2 pulses.

9

If you change the settings, you will receive a Settings SMS. This will have

the following format.

9. Meaning of abbreviations

The FenceAlarm uses abbreviations in order to carry out commands

quickly and correctly, and to display measurement values in the SMS

messages. It is important that you know what the commands mean. Below

you can find the abbreviations of the status SMS message.

M1:+31611112222

 Telephone number the SMS is sent to

PG:2 V37

 Software version.

GV:32

 Perimeter Voltage is 3.2kV

DT:30

 The day timer is set at 30 days

TM:006

 Reminder in the event of an Alarm every 6 hours

DG:168

 A status message once every 168 hours (once per week)

TP: 214415040310

 Current time and date (see explanation on page 13)

10

GSM STATUS

Batt 100%

The battery capacity is still 100%. When this value

reaches 20% it is time to change the batteries.

Signal 48%

GSM signal strength is 48%. The GSM signal strength

must not be less than 15%, otherwise there is a risk

the device will not be able to make a connection with

the network. In that case you would need to use a

SIM card of a different provider.

SMSno:5

A total of 5 SMS messages have been sent. The

FenceAlarm logs the number of SMS messages sent

for you. This will help you monitor the consumption

of the call credits. Check the balance and validity

period of the call credits now and again to ensure the

device continues to operate correctly.

M1:+31611112222

Telephone number the SMS is sent to by the

FenceAlarm. This should be the mobile telephone

number of the fence owner. Tip: always use the

country code for the mobile phone number

Fence STATUS

Batt 1 days

Energiser power pack consumption = 1 day. When

the FenceAlarm is activated, the day timer starts

counting from 0. This means you know how long the

power pack has already been in use, and based on

the capacity of the power pack and the energy

consumption of your energiser, you can calculate

how many days are left before the power pack has to

be replaced/recharged. This means that when you fit

a new power pack to your energiser, you have to

turn the FenceAlarm off and on again in order to

reset the day timer to 0.

RED: 7.1kV

Voltage measured on the red wire (RED) is 7.1kV. The

voltage measured on both wires is rounded off to a

10th of a kilovolt (i.e., in multiples of 100V).

YEL: 7.2kV

Voltage measured on the yellow wire (YEL) is 7.2kV

The voltage measured on both wires is rounded off

11

to a 10th of a kilovolt (i.e., in multiples of 100V)

Puls> 1.2sec

Measured interval between 2 pulses. This interval is

measured for you. Some energisers increase the

pulse interval when the power pack level is low. If

this happens, you know the power pack of the

energiser needs to be replaced.

If you use your own mobile telephone to change the settings of the

FenceAlarm you will be sent a settings SMS message.

SETTINGS

M1:+31611112222

Telephone number the SMS is sent to by the

FenceAlarm. This should be the mobile telephone

number of the fence owner. Tip: always use the

country code for the mobile phone number.

V37

Software version. This tells you the software version

installed on the FenceAlarm.

GV:32

Perimeter Voltage is 3.2kV.This is the minimal value

that will activate the FenceAlarm in sending a

FenceAlarm SMS message.

DT:30

The day timer is set at 30 days. You can set the time

that the battery of your energiser will last. The

FenceAlarm will send a FenceAlarm SMS message

after 30 days.

TM:006

TM is short for time. The alarm will be repeated

every 6 hours. If you receive an alarm message, the

FenceAlarm will continue sending (reminder)

messages to you at a set interval.

DG:168

DG is short for daily message. A status message will

be sent once every 168 hours (once per week). At set

intervals the FenceAlarm will send you a status SMS

message to keep you informed about the current

status of your fence. In this way the FenceAlarm lets

you know that everything is still working properly.

The standard setting is for the SMS to be sent at

20:00 hours. However, you still have to set the time

12

for this.

TP:214415040310

Current time and date. This is the time and date the

message was sent. The time and date in this example

is 21 hours, 44 minutes, 15 seconds on the 04 day of

the 03 month of the year 2010.

10. Changing the settings of the FenceAlarm

You can only change settings when the internal GSM of the FenceAlarm is

active. It is only active for a short while after an SMS message, or if you

switch the FenceAlarm to programming mode. See paragraph 4 – 1b

“changing settings”.

Set the time

When you change the date and time, please take into account that the

FenceAlarm operates with a 24 hours clock. When you, for instance, want

to set 1 o’clock in the afternoon on 5 April in 2010 (13:00:00 05/04/2010),

then you send an SMS message to the FenceAlarm: TP:130000050410.

Set the perimeter voltage

The perimeter voltage is the minimal value that will activate the

FenceAlarm in sending a FenceAlarm SMS message. If you want to set the

perimeter voltage in e.g. 4.0kV, send an SMS message to the FenceAlarm

with: GV:40. This value can be set between 2.0kV and 9.9kV.

Set the day timer

This feature is a Handy tool for portable energisers to keep track of the

durability of batteries. The day timer counts the days that the battery will

operate. So, if your energiser operates about 40 days on the used battery

then you send the following SMS message to the FenceAlarm: DT:40. This

value can be set between 00 and 00 days. If the battery voltage becomes

too low, then you will be notified through an SMS message as well.

13

Set the interval of status SMS messages

At set intervals the FenceAlarm will send you a status SMS message to

keep you informed about the current status of your fence. In this way the

FenceAlarm lets you know that everything is still working properly. The

standard setting is for the SMS to be sent at 20:00 hours. However, you

still have to set the time for this. If you wish to receive a status SMS

message, send an SMS message with: DG:48 to the FenceAlarm and you

will receive every 2 days at 8 o’clock at night an update on the status of

your fence. You can set this value between 00 and 250 hours.

Set the interval of FenceAlarm SMS messages

If you receive an alarm message, the FenceAlarm will continue sending

(reminder) messages to you at a set interval. You can change this interval

with this setting. You can set this value between 000 and 250 hours. The

default setting for this value is 6 hours. (TM:006). This means you will

receive a reminder once every 6 hours. If you want to change this interval

to 24 hours, for example, then you SMS TM:024 to the FenceAlarm.

Resetting the FenceAlarm

Switch the magnet to OFF for at least 10 seconds (the lamp has to go

out).To activate the Gallagher FenceAlarm switch the magnet from OFF to

ON. It may take a few minutes for it to start up.

14

1. Inleiding

Hartelijk dank voor de aanschaf van de Gallagher FenceAlarm.

Gallagher, wereldwijd marktleider in elektrische afrasteringen, wil

producten van topkwaliteit leveren. De SMS FenceAlarm is een unieke plug

and play beveiliging van uw afrastering. De FenceAlarm waarschuwt u op

uw mobiele telefoon per SMS bij onvoldoende voltage (door bijv.

begroeiing) of bij onderbreking van het raster (door bijv. het openen van

een poort).

Indien u om enige reden niet tevreden bent met uw aankoop, aarzel dan

niet om dit apparaat binnen 30 dagen na aankoop terug te sturen naar de

winkel waar u het aangeschaft heeft. Indien u vragen heeft betreffende dit

product, gelieve ons dan een e-mail te sturen:

info.nl@gallaghereurope.com, of neem contact op met de winkel waar u

dit Gallagher-product heeft aangeschaft.

Lees voor een goede werking van de FenceAlarm deze gebruiksaanwijzing

goed door.

2. Belangrijke informatie

 Schakel eerst het schrikdraadapparaat uit alvorens u de FenceAlarm

monteert of openschroeft.

 Laat lege batterijen niet in de FenceAlarm zitten. Lege batterijen

kunnen gaan lekken en schade veroorzaken aan de FenceAlarm.

 Zorg er voor dat er altijd voldoende beltegoed op de SIM-kaart van de

FenceAlarm staat en controleer dit regelmatig.

3. Gereedmaken voor gebruik

De FenceAlarm werkt alleen wanneer er een prepaid SIM-kaart geplaatst is

met voldoende beltegoed. Een SIM-kaart met abonnement is ook mogelijk.

Zorg in beide gevallen dat de voicemail is uitgeschakeld en dat de pincode

op “0000” staat (standaard instelling) of uitgeschakeld is.

15

Volg voor het plaatsen van de SIM-kaart de volgende stappen:

1. Schroef de 4 schroeven van het deksel open.

2. Plaats een SIM-kaart in de SIM-kaarthouder van de FenceAlarm met de

chip naar beneden. Zorg dat de SIM-kaart goed klemt tussen de

houder. De SIM-kaart rust op het deksel voorbij het rubber.

3. Plaats drie alkaline (niet-oplaadbare AA) batterijen in de

batterijhouder.

4. Schroef het kastje goed dicht. Let op dat er geen vuil o.i.d. tussen het

afdichtingrubber en het deksel zit zodat het kastje goed afgesloten is

voor vocht.

SIM

16

4. Telefoonnummer instellen/Instellingen wijzigen

Om de FenceAlarm te laten communiceren met een mobiele telefoon

dient u hiervoor een mobiel telefoonnummer in te voeren voor het

ontvangen van de SMS-rasterberichten. Het instellen van het

telefoonummer in De FenceAlarm gebeurt door het versturen van een

SMS-bericht.

1a. Typ een SMS-berichtje met de tekst M1:+31 gevolgd door uw mobiele

telefoonnummer. Verstuur deze nog

niet!

Let op:

 +31 is de landcode van Nederland.

Gebruikt u een Duits nummer,

vervang dan +31 door +49.

 De M moet met een

HOOFDLETTER.

 De “0” van het 06-nummer

weglaten achter de landcode.

 Alles moet aan elkaar getypt

worden, er mag geen spatie tussen

zitten

1b. Instellingen wijzigen/ resetten, Type een SMS-berichtje met de

gewenste instellingen (zie hoofdstuk 10). Verstuur deze nog niet!

2. Plaats de magneet minimaal

10 seconden op OFF, het

lampje mag nu niet meer

branden.

Stel dat uw eigen

mobiele nummer

0611112222 is. Stel

dat het nummer van

de SIM-kaart in het

FenceAlarm

0633334444 is.

Nu dient u een SMS-

bericht te versturen

met de tekst

M1:+31611112222 (M

in HOOFDLETTER) naar

0633334444

(FenceAlarm).

17

3. Schuif met de magneet een paar keer rustig heen en weer van OFF

naar ON. Ga hiermee door totdat het lampje één keer blauw oplicht.

Laat nu de magneet op ON staan.

4. Wacht tot De FenceAlarm afwisselend blauw en groen oplicht. De

FenceAlarm heeft nu verbinding met het GSM netwerk. U heeft nu

maximaal 2 minuten de tijd om de volgende stap uit te voeren.

Knippert het lampje niet meer afwisselend blauw en groen, dan

dient u stap 2 tot en met 4 opnieuw uit te voeren.

5. Verstuur vervolgens het SMS-berichtje uit stap 1a of 1b naar het

nummer van de SIM-kaart in de FenceAlarm.

6. Na enkele minuten ontvangt u een statusbericht. De inhoud van dit

statusbericht wordt verderop in deze handleiding nader toegelicht.

Vervolgens kunt u de FenceAlarm uitzetten, het telefoonnummer is nu

opgeslagen.

5. Aansluiten op het raster

Voor een goede werking dient de FenceAlarm fysiek zo ver mogelijk van

het schrikdraadapparaat verwijderd te zijn. Bij voorkeur dient de

FenceAlarm halverwege in het raster geplaatst te worden, waarbij de

hoeveelheid raster vanaf links ongeveer dezelfde lengte heeft als vanaf

rechts.

Ter hoogte van de FenceAlarm moet het raster uit beide richtingen

worden ontkoppelt. Dit kunt u doen door het raster uit beide richtingen

naar twee aparte isolatoren te leiden.

Sluit vervolgens op het ene ontkoppelde raster de rode klem aan en op het

andere ontkoppelde raster de gele klem.

De groene klem dient aangesloten te worden op een aardpen (niet

bijgeleverd).

18

6. Ingebruikname

Om de FenceAlarm aan te zetten schuift u de magneet van OFF naar ON.

De FenceAlarm wordt vervolgens automatisch actief.

Het opstarten kan enkele minuten duren. Zodra de FenceAlarm actief is,

zal het lampje iedere 12 seconden één keer groen oplichten. Dit is overdag

moeilijk te zien in verband met energiebesparing. U zult tevens een SMS-

statusbericht krijgen met actuele meetwaarden en instellingen.

19

7. Werking van de FenceAlarm

De FenceAlarm biedt u inzicht in de actuele rasterspanning gemeten vanuit

twee richtingen. Tevens wordt u gewaarschuwd wanneer de

rasterspanning al enige tijd onder het minimum is (bijvoorbeeld wanneer

wildgroei de werking van het raster belemmert). U ontvangt, zolang de

situatie niet hersteld is, regelmatig een herinnerings-SMS genaamd “Still

Alarm”.

De FenceAlarm komt direct in actie wanneer de rasterspanning uit een van

de richtingen helemaal verdwijnt, bijvoorbeeld wanneer er draden worden

doorgeknipt of op een andere wijze worden onderbroken.

De FenceAlarm meet de periodetijd tussen twee pulsen en stuurt deze

gemeten periodetijd mee in de status-SMS. Hiermee kunt u zien of het

apparaat in de batterijspaarstand staat, wat aangeeft dat u de batterij of

accu van het mobiele apparaat moet vervangen.

De FenceAlarm stuurt tevens op een instelbare interval (standaard één

keer per week) een SMS-statusbericht om u op de hoogte te houden van

de toestand en werking van het raster.

De FenceAlarm heeft een geïntegreerde dagenteller die aangeeft wanneer

de accu van een mobiel schrikdraadapparaat opgeladen dient te worden.

Deze timer is instelbaar en wanneer de tijd verstrijkt ontvangt u een SMS.

La page charge ...

Gallagher FenceAlarm Instructions Manual

Gallagher FenceAlarm Instructions Manual

dans d''autres langues

Documents connexes

Autres documents