NAPOLEON RXT625SIBNSS-1-A Le manuel du propriétaire

ROGUE

®

SERIES

Owner's Manual

RXT525PSS-1 & RXT625SIBPSS-1

Grills illustrated in this manual may differ

from model purchased.

Apply Serial Number

Visit Napoleon.com

to register your grill and write

a review, we want your feedback!

2

| Welcome

Napoleon.com | Rogue Series Grills

Welcome

WE WANT YOUR GRILLING EXPERIENCE TO BE MEMORABLE AND SAFE.

Please read and follow this Owner’s Manual before using your grill to avoid property damage, personal injury, or death.

Remove all packaging material, promotional labels and cards from the grill before use.

USE OUTDOORS IN A WELL-VENTILATED SPACE

DANGER!

IF YOU SMELL GAS

• Shut off gas to the appliance

• Extinguish any open ﬂame

• Open lid

• If odor continues, keep away from the appliance

and immediately call your gas supplier, or ﬁre

department

WARNING!

Do not try to light this appliance without reading the

“LIGHTING” instructions section of this manual

Do not store or use gasoline, or other ﬂammable liquids

or vapors in the vicinity of this or any other appliance

An L.P. (propane) cylinder not connected for use

must not be stored in the vicinity of this or any other

appliance

If the information in these instructions is not followed

exactly, a ﬁre or explosion may result and cause

property damage, personal injury, or death

Alert adults and children about the hazard of hot surface temperatures. Supervise young children near the grill.

NOTICE TO INSTALLER: Leave these instructions with the grill owner for future reference.

NOTICE TO CONSUMER: Keep these instructions for future reference.

CONGRATULATIONS

ON YOUR NAPOLEON GRILL!

You’ve Just Upgraded Your Grilling Game.

!

Napoleon.com | Rogue Series Grills

Welcome |

3

Welcome

Welcome to Napoleon!

Safety firSt

WARNING General Information

This grill should be installed in conformity with local codes. In

absence of local codes, install to the current Natural Gas and Propane

Installation Code CSA B149.1 in Canada, or the National Fuel Gas Code

ANSI Z223.1/NFPA 54 in the United States.

If a rotisserie motor is used, it must be electrically grounded in

accordance with local codes. In absence of local codes, follow the

current Canadian Electrical Code CSA C22.1 in Canada, or the National

Electrical Code ANSI/NFPA 70 in the United States.

WARNING! Installation & Assembly

Assemble this grill exactly as instructed in the Assembly Guide.

If the grill was assembled in-store, review the assembly instructions to

ensure it is done correctly.

Perform the required Leak Test before operating the grill.

Do not modify this grill under any circumstances.

Do not use a cylinder that is not equipped with a QCC1 type connection.

Only use the pressure regulator and hose assembly supplied with this

grill or replacement parts speciﬁcally recommended by Napoleon.

WARNING! Operation

Read this entire Owner’s Manual before operating this grill.

Leak Test this grill before each use, annually and when any gas

components are replaced.

Follow the lighting instructions carefully.

WARNING! Storage & Disuse

Turn off gas at the propane cylinder or natural gas supply valve.

Disconnect the hose between the propane cylinder and grill.

Remove the propane cylinder and store outdoors in a well-ventilated

space away from children.

DO NOT store propane cylinders in a building, garage, shed, or any other

enclosed space.

Disconnect the natural gas hook-up from the supply when storing the

grill indoors.

WARNING! California Proposition 65

This product can expose you to chemicals including soot, which

are known to the State of California to cause cancer, and chemicals

including carbon monoxide, which are known to the State of California to

cause birth defects or other reproductive harm. For more information go

to www.P65Warnings.ca.gov.

!

FC

ES

23

EMAIL

[email protected]

ONLINE

www.napoleon.com

PHONE:

1-866-820-8686

CONTENTS

Welcome to Napoleon! 3

Safety First

Full Rogue

®

System Features 4

Getting Started 5

Additional Safe Operating Practices

Gas Connections

Leak Test

Operation 9

Lighting your grill

Grilling Instructions

How to use the Rear Burner & Rotisserie

Grilling Tips

How to season your cooking grids

Infrared Grilling Guide 13

Cleaning Instructions 14

Maintenance Instructions 17

Combustion in air adjustment

Stainless in harsh environments

Troubleshooting 19

Warranty 21

45

4

| Features

Napoleon.com | Rogue Series Grills

Features

Full Rogue

®

System Features

The grills illustrated in this Owner’s Manual may differ from the model you purchased

!

Condiment Basket

to keep your

favourite sauces

and spices close on

hand

Rear Infrared

Rotisserie Burner

to enjoy succulent

rotisserie meals

Easy access drip

pan for efﬁcient

maintenance

Backlit Control

Knobs for

late night

entertaining

Stainless Steel Iconic

WAVE™ Cooking Grids

for those distinctive

sear marks and even

cooking

Dual-level Stainless

Steel Sear Plates for

consistent even heating

and vaporizing drippings

for more ﬂavourful food

Heavy Gauge

Stainless Steel

Burners for long

lasting quality

Instant JETFIRE™

Ignition for quick

and east start-up

Stainless Steel

Folding Side

Shelves with

Integrated Tool

Hooks

ACCU-PROBE™ Temperature

Gauge to easily read the

temperature for perfect results

Integrated Bottle

Opener close to the

grilling action

Propane Tank Ring

for stable tank

storage (propane

models only)

Easy Locking

Casters safely lock

the grill in position

Large chrome plated

Warming Rack for

increased cooking

area

Infrared SIZZLE

ZONE™ Side

Burner for

perfectly grilled

steaks

Napoleon.com | Rogue Series Grills

Getting Started |

5

Getting Started

DANGER / WARNING! Advises of a hazard that

could result in a fire, explosion, death or serious

physical injury.

WANING / CAUTION! Advises of a hazard that

could result in minor physical injury or property

damage.

Always wear protective gloves.

Always wear safety glasses.

CAUTION! Hot surface.

!

additional Safe operating practiceS

• Do not route the hose underneath the drip pan. Maintain

proper hose clearance to the bottom of the unit.

• Ensure sear plates are positioned properly according to

sear plate installation instructions.

• Burner controls must be off when turning the propane

cylinder valve on.

• Do not light burners with the lid closed.

• Do not operate the rear burner with the main burners.

• Do not close the side burner lid when operating or hot.

• Do not deep fry food on the side burner.

• Do not adjust the cooking grids when operating or hot.

• Maintenance should only be done when the grill is cool.

• Do not store lighters, matches or any other combustibles in

the condiment tray.

• Keep all electrical supply cords and fuel supply hoses

away from all heated surfaces. Clean the grease tray and

sear plates regularly to avoid build-up and grease ﬁres.

• Keep the infrared burner venturi tube free from spider

webs and other obstructions by inspecting and cleaning

it regularly.

• Do not allow cold water (rain, sprinkler, hose etc.) to

contact the heated grill. An immediate temperature

change will chip the porcelain and crack the ceramic

burners.

• Do not use a pressure washer to clean any part of the gas

grill.

• Never cover more than 75% of the cooking surface with

solid metal

Important information

Do not smoke while performing a gas leak test.

Sparks or ﬂames will cause a ﬁre, explosion,

damage to property, serious physical injury, or

death.

Never use an open ﬂame to check for gas leaks.

Sparks or ﬂames will cause a ﬁre, explosion,

damage to property, serious physical injury, or

death.

DANGER! Immediately shut off the gas supply

and disconnect.

!

STOP

Getting Started

CAUTION! The hook-up and installation of the natural gas and hose connection must be performed by a licensed gas

fitter, and leak tested before operating the grill.

CAUTION! Ensure the hoses do not contact any high temperature surfaces of the grill.

CAUTION! Do not move the grill when operating and hot.

!

6

| Getting Started

Napoleon.com | Rogue Series Grills

Getting Started

gaS connectionS

To a propane cylinder

Only use a 20 lb. (9.1 kg) propane cylinder constructed and marked

in accordance with the Speciﬁcations for LP gas Cylinders of the U.S.

Department of Transportation (D.O.T.) or the Standard for Cylinders,

Spheres and Tubes for Transportation of Dangerous Goods and

Commission, CAN/CSA-B339, as applicable.

Only use a gas pressure regulator speciﬁed by Napoleon. The

regulator must supply a pressure of 11 inches water column (0.39

psi) and have a QCC1 type ﬁtting.

The cylinder connection device must be compatible with the

connection for this outdoor appliance.

The propane cylinder must have:

• a shutoff valve with a QCC1 connection

• a safety relief device

• a collar to protect the valve

• a listed Overﬁll Protection Device

Hook-up and installation

• Check the cylinder for dents or rust, and have it inspected by

your propane supplier.

• Never use a cylinder with a damaged valve.

• Set cylinder into the hole in bottom of shelf. (1)

• The cylinder must ﬁt properly into the tank retaining ring. (2)

Proper hose connection

• Ensure the gas regulator hose has no kinks.

• Clip the hose to side panel using the supplied retainer clip. (3)

• Do not route the hose in close proximity to the drip pan.

• Remove the cap or plug from the cylinder fuel valve.

• Insert the black QCC1 regulator nipple onto the QCC1 fuel valve.

Hand tighten to right. Do not use tools. (4)

• Ensure the hose does not contact any high temperature surfaces

of the grill because it will melt and cause a ﬁre.

• Leak test all joints prior to operating the gas grill. See “LEAK

TEST” on page 8.

WARNING! Do not store a spare propane cylinder under or near this gas appliance.

WARNING! Never use a propane cylinder that is beyond 80% full.

WARNING! Follow all specifications and instructions exactly to prevent fire, explosion, property damage,

personal injury, or death.

!

1

3

2

4

Napoleon.com | Rogue Series Grills

Getting Started |

7

Getting Started

WARNING! Disconnect the grill and its individual shutoff valve from the gas supply piping system during any

pressure testing in excess of ½ psi (3.5 kPa).

WARNING! Close the individual shutoff valve to isolate the grill from the gas supply piping system during any

pressure testing equal to or less than ½ Psi (3.5 kPa).

WARNING! Check the hose for evidence of excessive abrasion, melting, cuts or cracks. If the hose is damaged, it

must be replaced with an assembly specifically recommended by Napoleon.

WARNING! Follow all specifications and instructions exactly to prevent fire, explosion, property damage,

personal injury, or death.

!

To a house gas supply line

• A gas supply hose and quick disconnect designed for natural gas and certiﬁed for outdoor use are included with

natural gas grills.

• Natural gas plumbing must supply a pressure of 7 inches water column pressure to the inlet of the grill.

• Piping and valves upstream of the quick disconnect are not supplied.

• The gas pipe must be sized to supply the BTU/h speciﬁed on the rating plate, based on the length of the piping

run.

• See “WARNING! General Information” on page 3 of this manual for installation codes.

Proper hose connection

1. Hook-up to a gas supply line must be performed by a licensed gas ﬁtter and leak tested before operating the grill.

2. Clip hose to side panel using the supplied retainer clip.

3. Do not route the hose in close proximity to the drip pan or over top of the back panel.

4. Ensure the hose does not contact any high temperature surfaces.

Quick disconnect

• Do not install the quick disconnect in an upward direction.

• A readily accessible manual shut-off valve must be installed upstream of the quick disconnect, and as close to it

as possible.

• Connect the ﬂared end of the hose to the ﬁtting on the end of the manifold tube or ﬂex tube (if applicable).

• Tighten using two wrenches. Do not use thread sealer or pipe dope.

• Leak test all joints prior to operating the gas grill. See “LEAK TEST” on page 8.

BE

CAREFUL

The lid of the grill and

the entire ﬁrebox can

become very hot when

in use.

8

| Getting Started

Napoleon.com | Rogue Series Grills

Getting Started

leak teSt

Why and When to Leak Test?

A leak test conﬁrms no gas is escaping after you

connect the hose to the gas supply.

Each time the tank is reﬁlled and reinstalled,

ensure that there are no leaks in the ﬁtting where

the regulator connects to the tank.

Leak test this grill before use, annually, and when

any gas components are replaced.

Leak Test Steps

1. Do not smoke while performing the test.

2. Remove all sources of ignition.

3. Turn all burner controls to the off position.

4. Turn the gas supply valve on.

5. Brush a half-and-half solution liquid soap and

water onto all joints and connections of the

regulator, hose, manifolds, and valves.

6. Bubbles indicate a gas leak.

WARNING! Never use an open flame to check for gas leaks. Sparks or flames will cause a fire, explosion, damage

to property, serious physical injury, or death.

WARNING! Only use the pressure regulator and hose assembly supplied with the grill.

!

If you ﬁnd a leak

1. Tighten any loose joints.

2. If the leak cannot be stopped, immediately shut off the gas

supply and disconnect the grill.

3. Have the grill inspected by a certiﬁed installer, or dealer.

4. Do not use the grill until the leak has been ﬁxed.

STOP

Napoleon.com | Rogue Series Grills

Operation |

9

Operation

lighting your grill

Is it the very ﬁrst time? Perform a Burn-off

Run the main burners on high for 30 minutes. It is normal for the

gas grill to emit an odor the ﬁrst time it is lit. This odor is caused

by the “burn-in” of internal paints and lubricants used in the

manufacturing process and will not occur again.

Main Burner Lighting

1. Open grill lid.

2. Push and slowly turn any main burner knob counter clockwise

to HIGH position until pilot lights. Continue to push down on

the control knob until the burner lights and then release.

3. If the pilot does not light – immediately turn the control knob

clockwise to the OFF position. Repeat step 2.

4. If the pilot and burner will not light in 5 seconds – turn the

control knob clockwise to the OFF position. Wait 5 minutes for

gas to dissipate. Repeat steps 2 and 3, or light with a match.

Rear Burner Lighting (if equipped)

1. Open grill lid.

2. Remove warming rack.

3. Push and slowly turn rear burner knob counter clockwise to

HIGH position.

4. Press and hold igniter button until the burner lights, or light

by match.

5. If the burner will not light – turn burner control knob

clockwise to the OFF position. Wait 5 minutes. Repeat step 4.

(Fig. 1)

Side Burner Lighting (if equipped)

1. Open burner cover.

2. Push and slowly turn side burner knob counter clockwise to

HIGH position.

3. Press and hold igniter button until the burner lights, or light

by match.

4. If the burner will not ignite – turn burner control knob

clockwise to the OFF position. Wait 5 minutes. Repeat step 3.

(Fig. 2)

Lighting with a match

1. Clip the match into the supplied lighting rod.

2. Insert the lit match through the cooking grids and sear plates

3. while turning the corresponding burner knob to high.

(Fig. 3)

WARNING! Make sure the lid of

the grill is OPEN while igniting.

WARNING! Ensure all burner

controls are in the OFF position before

slowly turning on gas supply valve.

WARNING! Do not use the rear burner

while operating the main burner.

Operation

!

Side Burner

Igniter

Right Centre

Burner

Left Centre

Burner

Left Burner

Right Burner

Centre Burner

WARNING! Follow the lighting instructions carefully.

WARNING! Do not store lighters, matches or any other

combustibles in the condiment tray.

WARNING! Do not adjust the cooking grids while the grill is

hot, or operating.

!

1

2

3

2

3

4

3

1

2

3

Fig. 1

Fig. 2

Fig. 3

10

| Operation

Napoleon.com | Rogue Series Grills

Operation

WARNING! Never grill food directly on the flame side burner. It is designed for use with pots and pans only.

WARNING! Do not close side burner lid while it is operating or hot.

WARNING! Do not deep fry food on the side burner. Cooking with oil can be dangerous.

WARNING! Regularly clean grease out of the entire unit, including the grease tray and the sear plates, to avoid

build-up and grease fires.

!

grilling inStructionS

Main Burner Use

• Preheat the grill before searing food by operating

all main burners on high with the lid closed for

approximately 10 minutes.

• Food cooked for only a short time such as ﬁsh and

vegetables can be grilled with the lid open.

• Grilling with the lid closed ensures higher and

consistent temperatures that cook meat more evenly

and can reduce cooking times.

• The cooking grids can be oiled before pre-heating

to reduce sticking when grilling lean meat such as

chicken breast, or pork.

Direct Grilling

This method is often used for searing, or food cooked for only a short

time such as hamburgers, steaks, chicken, or vegetables.

Place food on the cooking grids directly over the heat.

Sear meat ﬁrst to trap-in the juices and ﬂavor.

Lower the grill temperature to ﬁnish cooking to your preference.

Indirect Grilling

This method uses lower temperatures and circulates heat around the

food cooking it slowly and evenly.

Use this method to cook larger cuts of meat, or food prone to ﬂare-ups

such as roast, chicken, or turkey.

Turn one or more burners on and place food on the cooking grid where

there is no ﬂame, or burner on.

Grilling at a lower temperature and slower cooking time results in more

tender meats.

Flame Side Burner (if equipped)

The ﬂame side burner can be used like a stove top to make gravy or

soups.

The recommended pot or pan diameter is 10” (25 cm)

Be sure your grill is in a location protected from the wind, or the

performance of the side burner will be affected.

Grilling at night

Illuminate the control knobs by pushing the lightbulb icon on the control

panel.

• Food that takes longer than 30 minutes such as roasts can be

cooked indirectly with the burner lit opposite the food. See

Indirect Grilling.

• Trim excess fat off meat to prevent flare-ups, or reduce the

temperature of the grill.

• Flare ups – move food away from the flames and reduce the

heat. Leave the lid open.

GRILLING

PRO TIP!

Use a thermometer

to check the internal

temperature of meat

to ensure it is cooked

perfectly

GRILLING

PRO TIP!

Add a Napoleon

smoker accessory to

your grill to ﬂavor your

meat.

Napoleon.com | Rogue Series Grills

Operation |

11

Operation

how to uSe the rear Burner & rotiSSerie

(IF EQUIPPED)

Using the rear burner and spit rod

1. Remove the warming rack prior to using the rear burner and

spit rod. Extreme heat will damage the warming rack.

2. Remove the rotisserie motor from the gas grill.

3. Install the rotisserie motor on the applicable brackets.

Thread the meat you’re cooking onto the spit rod along with

the rotisserie fork. Slide the meat into the rotisserie fork to

hold in place.

4. Slide the second rotisserie fork onto the opposite end of the

spit rod and push into other end of meat until secure.

WARNING! Barbecue sauce and salt can be corrosive and will cause rapid deterioration of the gas grill

components unless cleaned regularly.

WARNING! Disassemble rotisserie components when finished cooking, wash with warm soapy water, and store

indoors.

WARNING! Use heat resistant grilling gloves when handling the hot rotisserie components.

!

5. Slide the counterbalance onto the spit rod.

6. Hang the spit rod across the hangers. The heavy side of

the meat will naturally hang down.

7. Tighten the counterbalance arm and weight, so the arm

is facing up.

8. Slide the counterweight accordingly to balance the load,

and tighten in place.

9. Reinstall motor. Begin cooking.

10. Place a metal dish under the meat to collect the

drippings.

Tips about using the rotisserie:

• Operate the rear burner on high until the meat

browns. Reduce heat. Keep lid closed. Cook

thoroughly.

• Use a thermometer to check the internal

temperature of the meat.

• Roasts and poultry should brown on the outside

and stay tender on the inside.

• Use drippings to baste and make gravy.

• A 3-pound chicken takes approximately 1 ½

hours on medium to high.

How to cook up to 3 chickens

1. Tie or skewer wings to the body of the

chickens.

2. Thread rotisserie fork onto spit rod.

3. Thread ﬁrst chicken onto spit rod until it

is held into place by the rotisserie fork.

Tighten.

4. Thread next 2 chickens onto spit rod so all

the chickens are close together.

5. Thread second rotisserie fork onto spit rod

and push into chicken until all 3 chickens

are squeezed together tightly. Tighten.

5

4

3

6

2

1

7

DID YOU

KNOW?

You can remove the

cooking grids if they

interfere with cooking

larger cuts of meat.

12

| Operation

Napoleon.com | Rogue Series Grills

Operation

grilling tipS

Every time you grill checklist

☐

Read Owner’s Manual

Be sure to have read the owner’s manual and all the safety

instructions.

☐

Clean grease tray

Always ensure you clean the grease tray prior to grilling to avoid

fires and flare-ups.

☐

Check the hose

Ensure the gas grill is off and cool. Check the hose for evidence

of excessive abrasions, or cuts. Have the hose replaced before

use if the hose is damaged.

☐

Preheat and clean grids

Coat entire surface of grids with vegetable shortening NOT

salted fats like butter or margarine. Preheat your grill to burn

off excess residue. Clean grids with a brass wire brush. See

Cleaning Instructions section.

NOTE: Stainless steel cooking grids are durable and corrosion

resistant and require less seasoning and maintenance than cast

iron grids.

☐

Prep area

Make sure everything you need while grilling such as your

utensils, seasonings, sauces, and dishes are within your reach.

Don’t leave your food unattended, or it could burn.

☐

Don’t peek and flip once

Try not to open the lid and peek too much, or heat will escape

and throw your temperature and cooking times off. Flip your food

only once, especially steak and chicken.

☐

Leave space

Leave some space on the grill and between food, so you have

room to move food around if you need to.

☐

Use a thermometer

Use a thermometer to ensure food is cooked thoroughly. Follow

the appropriate temperatures guidelines for all types of meat,

especially poultry.

how to SeaSon your cooking gridS

1. Use a soft cloth to coat cooking grids with vegetable

shortening, NOT salted fats like butter or margarine.

2. Place seasoned grids in the grill.

3. Close lid and turn burner controls to MEDIUM.

4. Allow to heat for 30 minutes.

5. Turn all burner controls to the OFF position.

Turn off the gas at source.

6. Let the grids cool.

GRILLING

PRO TIP!

Always preheat the

grill before cooking

to burn off leftover

residue and prevent

food from sticking to

the grate.

GRILLING

PRO TIP!

Get inspired to create

delicious meals from the

recipes and grilling

techniques at

www.napoleon.com and

Napoleon's cookbooks

Napoleon.com | Rogue Series Grills

Grilling Guide |

13

Grilling Guide

Infrared Grilling Guide

FOOD CONTROL KNOB SETTING COOKING TIME SUGGESTIONS

Steak

1 inch (2.54 cm) thick

HIGH – 2 minutes each side

Rare – 4 minutes

Ask for marbled fat in cut.

Fat is a natural tenderizer

and keeps meat juicy.

HIGH to MEDIUM – High

heat 2 minutes each side

then turn to medium heat

Medium – 6 minutes

Well done – 8 minutes

Hamburger

½ inch (1.27 cm) thick

HIGH – 2 minutes each side Rare – 4 minutes

Keep patties all the same

thickness for equal cooking

times. Patties 1 inch thick or

more should be grilled using

indirect heat.

HIGH – 2 ½ minutes each

side

Medium – 5 minutes

HIGH – 3 minutes each side Well done – 6 minutes

Chicken

HIGH, MEDIUM, LOW – 2

minutes each side then

medium-low to low heat

20 – 25 minutes

Slice joint connecting the

thigh and leg ¾ through for

the meat to lie ﬂat on the

burner and cook evenly.

Pork Chops

MEDIUM 6 minutes each side

Choose thick cuts for more

tender meat. Trim off excess

fat.

Spare Ribs

HIGH to LOW – High for

5 minutes then low until

ﬁnished

20 minutes each side

turning often

Choose lean meaty ribs. Grill

until meat pulls easily from

the bone.

Lamb Chops

HIGH to MEDIUM – High

for 5 minutes then Medium

until ﬁnished

15 minutes each side

Choose thick cuts for more

tender meat. Trim off excess

fat

Hot dogs

MEDIUM to LOW 4 – 6 minutes

Select larger wieners and slit

lengthwise before grilling

14

| Cleaning

Napoleon.com | Rogue Series Grills

Cleaning

Cleaning Instructions

First time use

1. Wash grids by hand with water and mild dish soap to remove

any residue from the manufacturing process. DO NOT wash in a

dishwasher.

2. Rinse thoroughly with hot water and dry completely with a soft cloth

to prevent moisture from entering the cast iron

Cast Iron grids

• Coat the entire surface of the grids with vegetable shortening NOT

salted fats like butter or margarine.

• Preheat your grill to burn off excess residue.

• Clean grids with a brass wire brush.

• Steel wool can be used for stubborn stains. Use heat resistant

grilling gloves when handling hot grids.

• Season your grids to add a protective coating to prevent corrosion

See Grilling Tips – How to season your grill.

Stainless Steel Grids

• Stainless steel cooking grids can be cleaned by preheating the grill

and using a wire brush to remove residue.

• Stainless steel grids will permanently discolor from regular use

because of high temperatures when grilling.

Infrared side burner

• Most drippings and food particles that fall on the infrared burner

surface incinerates immediately because of the high intensity heat.

• Do not clean the ceramic tile with a wire brush.

• Do not use water or other liquids to clean the burner. An immediate

change in temperature will cause cracking of the ceramic tile.

• Light burner and operate on high for 5-10 minutes to remove any

left-over residue.

Inside of the grill

1. Remove the cooking grids.

2. Use a brass wire brush to clean loose debris from the casting sides

and underneath the lid.

3. Scrape the sear plates with a putty knife or scraper. Use a wire

brush to remove the ash.

4. Remove the sear plates and brush debris from the burners with a

wire brush.

5. Sweep debris from inside the grill into the drip pan.

WARNING! Always wear protective gloves and safety glasses when cleaning your grill.

WARNING! Accumulated grease is a fire hazard.

WARNING! Cleaning should only be done when the grill is cool to avoid the possibility of

burns.

!

Napoleon.com | Rogue Series Grills

Cleaning |

15

Cleaning

WARNING! Ensure all burners are turned off and grill is cool before cleaning. Do not use oven cleaner to clean any

part of the grill. Do not put cooking grids or any other parts of the grill in a self-cleaning oven to clean. Clean the

grill in an area where cleaning solution won’t harm decks, lawns, or patios.

WARNING! Barbecue sauce and salt can be corrosive and will cause rapid deterioration of the gas grill

components unless cleaned regularly.

Drip pan

• Grease and excess drippings collect in the drip pan

located beneath the grill and accumulate in the

disposable grease tray below the drip pan.

• Never line the drip pan with aluminum foil, sand or

any other material. This can prevent grease from

flowing properly.

• Clean frequently to avoid grease build-up:

approximately every 2 to 4 uses.

Cleaning steps:

1. Slide the drip pan from the grill to access the

disposable grease tray or to clean the drip pan.

2. Scrape the drip pan out with a putty knife or

scraper.

3. Replace the disposable grease tray every 2 or 3

weeks depending on grill usage.

4. See your Napoleon Grill dealer for supplies.

Control panel

ONLY use warm soapy water or stainless steel cleaner.

The control panel text is printed directly on the stainless

steel and will gradually rub off if abrasive cleaners are

used. Proper cleaning of the control panel will ensure text

remains dark and legible.

Aluminum castings

Clean with warm soapy water. Aluminum doesn’t rust, but

high temperatures and weathering can cause oxidization

on the surface of the castings that look like white spots.

See Maintenance Instructions section for directions on how

to repair and paint oxidized aluminium.

Outside grill surface

• Only use a stainless steel non-abrasive cleaner.

Abrasive cleaners or steel wool will scratch the ﬁnish.

• Always wipe in the direction of the grain.

• Handle porcelain enamel components with care.

• The baked-on enamel ﬁnish is glass-like and will chip

if struck.

• Touch up enamel is available at your Napoleon Grill

dealer.

• Stainless steel parts discolor overtime when heated

and will turn a golden or brown hue. This is normal

and won’t affect the performance of the grill.

!

16

| Cleaning

Napoleon.com | Rogue Series Grills

Cleaning

Insect screen and burner ports

Spiders and insects are attracted to the smell of propane and natural

gas. Napoleon has equipped the burner with an insect screen on the

air shutter. This reduces the likelihood of insects building nests inside

the burner, but doesn’t eliminate the problem.

A nest or web can cause the burner ﬂame to burn a soft yellow or

orange and cause a ﬁre or ﬂashback at the air shutter underneath the

control panel.

1. Remove the screw (s) that attaches the burner to the back wall of

the gas grill. Slide the burner back and upwards to remove.

2. Use a ﬂexible venturi tube brush to clean the inside of the

burner.

3. Shake loose debris from the burner through the gas inlet.

4. Check the burner ports and valve oriﬁces for blockages: burner

ports can close over time because of cooking debris and

corrosion.

5. Use an opened paperclip, or the supplied port maintenance bit to

clean burner ports.

6. Drill out blocked ports using the supplied drill bit in a small

cordless drill: this can be done with the burner attached to the

grill, but it’s easier if removed from the grill.

7. Do not ﬂex the drill bit when drilling the ports because the drill

bit will break.

8. This drill bit is for burner ports NOT for brass oriﬁces that

regulate the ﬂow of the burner.

9. Do not enlarge the holes

10. Ensure the insect screen is clean, tight, and free of any lint or

other debris.

11. Reverse the procedure to reinstall the burner.

12. Ensure the valve enters the burner when installing.

13. Replace sear plate mount and tighten screws to complete

reinstallation.

WARNING! It is very important the valve/orifice enters the burner tube when reinstalling the burner after cleaning

and before lighting your gas grill, or a fire or explosion could occur.

WARNING! Avoid unprotected contact with hot surfaces.

WARNING! Do not use abrasive cleaners or steel wool on any painted, porcelain, or stainless steel parts of your

gas grill because it will scratch the finish.

!

SAFETY

FIRST!

Always wear

protective gloves and

safety glasses when

servicing your grill.

Napoleon.com | Rogue Series Grills

Maintenance |

17

Maintenance

Maintenance Instructions

RECOMMENDATIONS

This grill should be thoroughly inspected and serviced annually by a qualiﬁed service person.

• Do not obstruct the ﬂow of ventilation and combustion air.

• Keep the cylinder enclosure ventilation openings located on the side of the cart and front and back of the bottom shelf

clear from debris.

WARNING! Keep the grill away from combustible materials, gasoline, and other flammable vapors and

liquids.

!

comBuStion in air adjuStment

!

IMPORTANT! This must be done by a qualified gas installer

• The air shutter is factory set and should not require adjusting

under normal conditions. Adjustments might be required under

extreme ﬁeld conditions.

• The ﬂames of the air shutter will be dark blue, tipped with light

blue and occasionally yellow when adjusted correctly.

• Too little air ﬂow to the burner will produce soot and lazy yellow

ﬂames.

• Too much air ﬂow to the burner will cause ﬂames to lift erratically

and cause igniting difﬁculties.

Adjusting the air shutter

1. Remove cooking grids and sear plates. Leave lid open.

2. You may have to open the cabinet door or remove the top drawer

(if equipped) to access the air shutter screw located at the mouth

of the burner.

3. Remove the back cover to adjust rear tube burner air shutter.

4. Loosen air shutter lock screw and open or close air shutter as

required.

Main Tube Burner Propane Natural Gas

RXT525 ½” (13 mm) 3/8” (10 mm)

RXT625 ½” (13 mm) 3/8” (10 mm)

Note: Infrared burners have no air adjustment.

5. Light the burners on high.

6. Visually inspect burner ﬂames.

7. Turn burners off, tighten locking screws, and replace removed

parts when shutters are set correctly.

8. Ensure insect screens are installed

WE WANT

TO HELP!

Contact the Napoleon

Customer Solutions

Department for

recommended

replacement

parts. 1-888-721-8324.

Burner Port

Yellow Tip

Dark Blue

Light Blue

18

| Maintenance

Napoleon.com | Rogue Series Grills

Maintenance

StainleSS in harSh environmentS

Stainless steel oxidizes or stains in the presence of chlorides and

sulﬁdes, especially in coastal regions, warm and highly humid areas,

and around pools and hot tubs. These stains look like rust, but they

can be easily removed or prevented. Wash stainless and chrome

surfaces every 3-4 weeks.

Burner maintenance

• Extreme heat and a corrosive environment can cause surface

corrosion to occur even though the burner is made from heavy wall

304 stainless steel.

Maintenance and protection of infrared burners

Your infrared burners are designed to provide a long service life, but

you must be careful to prevent cracking of their ceramic surfaces

Fractures will cause the burners to malfunction.

IMPORTANT! Damage caused by failure to follow these

instructions is NOT covered by your grill warranty.

Steps to avoid damaging ceramic surfaces

1. Never douse a ﬂame or control ﬂare-ups with water.

2. Do not allow cold water (rain, sprinkler, hose etc.) to come in

contact with hot ceramic burners. An immediate change in

temperature will cause cracking of the ceramic tile.

3. A ceramic burner that becomes wet before use will create steam

when operated later and produce pressure that will crack the

ceramic.

4. Repeated soaking of the ceramic can cause it to swell and expand

producing pressure that will make the ceramic crack and crumble.

5. Inspect the ceramic for possible water soaking if you ﬁnd standing

water in the grill. Remove the burner if the ceramic is wet. Turn it

upside down to drain the excess water. Bring ceramic indoors to

dry thoroughly.

6. Do not allow hard objects to impact the burner. Take care when

inserting or removing cooking grids and using accessories.

Impaired ventilation of hot air from the grill

• Hot air must have a way to escape the grill for the burners to

function properly.

• The burners can become deprived of oxygen if the hot air is not

allowed to escape causing them to back-ﬂash. The ceramic can

crack if this occurs repeatedly.

Hose Maintenance

• Inspect the hose before each use. Do not use the hose if there is

evidence of excessive abrasions, melting or cuts.

• If the hose is damaged, replace it with a regulator and hose

assembly specifically recommended by Napoleon.

!

WARNING! Turn off gas at the source and disconnect the unit before servicing.

WARNING! Maintenance should only be done when the grill is cool to avoid the possibility of burns.

WARNING! A leak test must be performed annually and when any component of the gas train is replaced, or

when the smell of gas is present.

!

SAFETY

FIRST

Never cover more than

75% of the cooking

surface with solid

metal i.e. griddle or

large pan.

Napoleon.com | Rogue Series Grills

Troubleshooting |

19

Troubleshooting

Lighting problems

• Main, rear or side burners will not light with the igniter, but will light with a match.

• Burners will not cross light each other

Possible causes Solution

Main

Burner

JETFIRE

TM

outlet is dirty or clogged Clean JETFIRE

TM

outlet with a soft bristle brush.

Dirty or corroded cross light brackets. Clean or replace as required.

Rear and Side

Burners

Dead battery, or installed incorrectly. Replace with premium heavy- duty battery.

Loose electrode wire, or switch terminal wires.

Check electrode wire is ﬁrmly pushed onto the terminal on the

back of the igniter. Check the lead wires from the module to the

ignition switch (if equipped) are ﬁrmly pushed onto their respective

terminals.

Lifting ﬂames on burner.

Close air shutter according to Maintenance Instructions-Combustion

Air Adjustment section in this Owner’s Manual.

IMPORTANT! This must be done by a qualified gas installer.

Infrared burner ﬂashes back.

• During operation the burner abruptly makes a loud whoosh sound, followed by a continuous blow-torch type sound and

grows dim.

Possible causes Solution

Ceramic tiles overloaded with grease drippings and build-

up. Ports are clogged

Turner burner OFF and allow to cool for at least 2 minutes. Reignite

burner and burn on HIGH for at least 5 minutes, or until the

ceramic tiles are evenly glowing red.

Burner overheated because inadequate ventilation. Too

much grill surface covered by griddle or pan.

Ensure no more than 75% of the grill surface is covered by objects

or accessories. Turn burner OFF and allow to cool for at least 2

minutes. Reignite.

Leaking gasket surrounding the ceramic tile, or a weld

failure in the burner housing.

Allow burner to cool and inspect very closely for cracks. Contact

your authorized Napoleon dealer to order replacement burner

assembly if any cracks are found.

Leaking gasket surrounding the ceramic tile, or a weld

failure in the burner housing.

Contact your authorized Napoleon dealer for instructions on

ordering a replacement burner assembly.

WE WANT

TO HELP!

Napoleon is here to

ensure your grilling

experience is

memorable. Contact

us if you require

additional help.

REGISTER

YOUR GRILL!

Register your grill! Go

to Napoleon.com or

your Assemby Guide

for replacement parts

instructions.

1

2

3

20

| Troubleshooting

Napoleon.com | Rogue Series Grills

Troubleshooting

Gas ﬂow.

• Low heat or low ﬂame when valve is turned to high

• Burners burn with yellow ﬂame, accompanied by the smell of gas

• Flames lift away from burner, accompanied by the smell of gas, and possible lighting difﬁculties.

• Burner output on HIGH, but setting is LOW. Rumbling noise and ﬂuttering blue ﬂame at burner surface.

Possible causes Solution

Propane – improper lighting procedure

Ensure lighting procedure is followed carefully. All gas valves must

be in the OFF position when the tank valve is turned on. Turn tank

on slowly to allow pressure to equalize. See Operation – Lighting

Instructions

Natural gas – undersized supply line. Pipe must be sized according to installation code.

Leaking gasket surrounding the ceramic tile, or a weld

failure in the burner housing.

Allow burner to cool and inspect very closely for cracks. Contact

your authorized Napoleon dealer to order replacement burner

assembly if any cracks are found.

Both gas propane and natural gas – improper preheating. Preheat grill with both main burners on high for 10 to 15 minutes.

Possible spider web or other debris.

Thoroughly clean nest or webs out of your burner oriﬁce by

removing it and following instructions in this manual.

See “INSECT SCREEN AND BURNER PORT” on page 16.

Improper air shutter adjustment.

Open or close air shutter slightly according to the instructions on

this manual. See “ADJUSTING AIR SHUTTER” on page 17.

IMPORTANT! This must be done by a qualified gas installer.

Lack of gas Check gas level in propane cylinder.

Supply hose is pinched. Reposition supply hose as necessary.

Propane regulator in low ﬂow state.

Ensure igniting procedure is followed carefully. All gas valves must

be in the OFF position when the tank valve is turned on. Turn tank

on slowly to allow pressure to equalize. See Operation – Igniting

Instructions.

Peeling paint, Noises and Flare-ups.

• Humming regulator

• Excessive ﬂare-ups and uneven heat

Possible causes Solution

Normal humming noise on hot days.

This isn’t a defect. It’s caused by internal vibrations in the regulator

and doesn’t affect the performance or safety of the gas grill.

Humming regulators WILL NOT be replaced.

The cylinder valve was opened too quickly. Open cylinder valve slowly

Sear plates installed incorrectly.

Ensure sear plates are installed with holes towards the front, and

the slots on the bottom. See Assembly Instructions Guide.

Improper heating. Preheat grill with both main burners on high for 10 to 15 minutes.

Excessive grease and ash build on sear plates and in drip

pan.

Clean sear plates and drip pan regularly. Do not line pan with

aluminium foil. Refer to Cleaning Instructions.

• Paint appears to be peeling inside lid or hood

Possible causes Solution

Grease build-up on inside surfaces.

This is not a defect. The ﬁnish on the lid and hood is porcelain,

and will not peel. The peeling is caused by hardened grease, which

dries into paint-like shards, that ﬂake off. Regular cleaning will

prevent this. See cleaning instructions.

La page est en cours de chargement...

NAPOLEON RXT625SIBNSS-1-A Le manuel du propriétaire

NAPOLEON RXT625SIBNSS-1-A Le manuel du propriétaire

dans d''autres langues

Documents connexes