Viking Range VDUI5240DSS Manuel utilisateur

Marque: Viking Range

Modèle: VDUI5240DSS

Taper: Manuel utilisateur

Install / Use & Care

MANUAL

5 SERIES

Refrigerated Drawers

Tiroirs Réfrigérés

Gavetas Refrogeradas

VDUI5240

FR-D’installation/d’utilisation et d’entretien

ES-De instalación/operación y mantenimiento

NOTE

CAUTION

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the anti-tip device .................................................6

Product dimensions ............................................................8

Using your Electronic control ............................................10

Starting your appliance ..................................................10

Sleep mode ...................................................................10

Turning your appliance "ON" or "OFF" ..........................10

Adjusting the temperature .............................................11

Temperature mode ........................................................11

Control lock ....................................................................11

Temperature sensor error codes ....................................11

Alarms ...........................................................................12

Door (drawer) ajar.....................................................12

Power failure ............................................................12

Temperature alarm ...................................................12

Vacation mode ................................................................13

Care and cleaning .............................................................13

Energy saving tips ............................................................14

Obtaining service .............................................................14

Troubleshooting ................................................................15

Warranty ...........................................................................16

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

CAUTION-Hazards or unsafe practices which could

result in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

CONTENTS

WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

NOTE

CAUTION

WARNING

XXXXXXXXXXXX

VIKING RANGE, LLC

GREENWOOD, MS 38930

UNPACKING YOUR APPLIANCE

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.vikingrange.com

The following information will be

required when registering your

appliance.

Service Number

Rev. Letter

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on

the serial plate which is located inside the cabinet on the

bottom of the liner toward the left side. Open the bottom

drawer to view it. See ﬁ gure 1.

Warranty Registration

Online registration

available at

www.vikingrange.com

Figure 1

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

CAUTION

Figure 2

Front Leveling

Legs

Front Grille,

keep this area

open.

Rear

Leveling

Legs

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources.

To ensure your product performs to speciﬁ cations, the

recommended installation location temperature range is

from 55 to 100°F (13 to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the

appliance. Keep this area open and clear of any

obstructions. Adjacent cabinets and counter top can be

installed around the appliance as long as the front grille

remains unobstructed.

Front Grille

Do not obstruct the front grille. The openings within

the front grille allow air to ﬂ ow through the condenser

heat exchanger. Restrictions to this air ﬂ ow will result in

increased energy usage and loss of cooling capacity. For

this reason it is important this area to not be obstructed and

the grille openings kept clean. Viking Range,LLC does not

recommend the use of a custom made grille as air ﬂ ow may

be restricted. (See Figure 2).

Leveling Legs

Adjustable legs at the front and rear corners of the

appliance should be set so the unit is ﬁ rmly positioned on

the ﬂ oor and level from side to side and front to back. The

overall height of your appliance may be adjusted between

the minimum, 33

⁄4" (85.7 cm), by turning the leveling leg in

(CW ↷) and the maximum, 34

⁄4" (88.3 cm) by turning the

leveling leg out (CCW ↶).

To adjust the leveling legs, place the appliance on a solid

surface and protect the ﬂ oor beneath the legs to avoid

scratching the ﬂ oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the

appliance forward using caution. On a level surface check

the appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille

adjusted to the desired height. When adjustment is

complete tighten the two front grille screws. (See Figure 5).

I NSTALLING YOUR APPLIANCE

NOTE

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any

circumstances, be installed to an un-grounded

electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

WARNING

Ground Fault Circuit Interrupters (GFCI) are prone to

nuisance tripping which will cause the appliance to shut

down. GFCI’s are generally not used on circuits with power

equipment that must run unattended for long periods of

time, unless required to meet local building codes and

ordinances.

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must

be plugged into a mating grounding type receptacle

in accordance with the National Electrical Code and

applicable local codes and ordinances (see Figure 6). If the

circuit does not have a grounding type receptacle, it is the

responsibility and obligation of the customer to provide the

proper power supply. The third ground prong should not,

under any circumstances, be cut or removed.

Figure 6

Figure 5

Front grille screw

Front grille

I NSTALLING YOUR APPLIANCE

Figure 3

Figure 4

Do not remove

ground prong

INSTALLING THE ANTI TIP DEVICE FOR FREESTANDING INSTALLATIONS

Step by step instructions for locating the po-

sition of the bracket:

1) Decide where you want to place the drawer refrigerator.

Slide it into place, being careful not to damage the ﬂ oor,

leaving 1" (2.5 cm) of clearance from the rear wall to allow

room for the anti-tip bracket.

2) Raise the rear leveling legs approximately

⁄4" (6 mm) to

allow engagement with the anti-tip bracket. Level the unit

by adjusting all the leveling legs as required. Turning the

leveling leg counterclockwise will raise the unit and clock-

wise will lower the unit.

3) Make sure the refrigerator is in the desired location, then

mark on the ﬂ oor the rear and side corner of the cabinet

where the anti-tip bracket will be installed. If the installation

does not allow marking the rear corner of the cabinet, then

make temporary lines on the ﬂ oor marking the front corner

of the cabinet, excluding the drawer. Slide the refrigerator

out of the way. From the temporary line extend the sidewall

line back 21

⁄2" (54.6 cm) as shown in Figure 8.

4) Align the anti-tip bracket to the marks on the ﬂ oor so

the side of the bracket lines up with the side of the cabinet

mark, and the "V" notches on the anti-tip bracket line up

with the end of the 21

⁄2" (54.6 cm) line (Rear of cabinet

line).

5) Fasten the anti-tip bracket to the ﬂ oor using the supplied

screw. (See Figure 8).

6) Slide the cabinet back into position, making sure the rear

cabinet leveling leg slides under the anti-tip bracket engag-

ing the slot.

Bottom View of

Refrigerated

Drawer Unit

Anti-Tip

Bracket

Leveling Leg

Front of cabinet

⁄2"

(54.6 cm)

Figure 7

WARNING

• ALL APPLIANCES CAN TIP

RESULTING IN INJURY.

• INSTALL THE ANTI-TIP

BRACKET PACKED WITH

THE APPLIANCE.

• FOLLOW THE

INSTRUCTIONS BELOW

Floor Mount Installation

The anti-tip bracket is to be located on the ﬂ oor in the left

or right rear corner of the refrigerator drawer as shown in

Figure 7.

CAUTION

NOTE

Any ﬁ nished ﬂ ooring should be protected with appropriate

material to avoid damage when moving the unit.

If installing on a concrete ﬂ oor, concrete fasteners are

required, (not included with the anti-tip kit).

Anti-Tip Device

WARNING

If your refrigerator is not located under a counter

top (free standing), you must use an anti-tip device

installed as per these instructions. If the refrigerator is

removed from its location for any reason, make sure

that the device is properly engaged with the anti-tip

bracket when you push the refrigerator back into the

original location. If the device is not properly engaged,

there is a risk of the refrigerator tipping over, with the

potential for property damage or personal injury.

INSTALLING THE ANTI TIP DEVICE FOR FREESTANDING INSTALLATIONS

⁄2"

(54.6 cm)

"V" notches

in bracket

"V" notches

in bracket

Figure 8

Rear of cabinet line

Figure 8a

Side of cabinet line

Front of cabinet line

Screw

Rear Leveling leg

"A"

"B"

"C"

"D"

"E"

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H"

VDUI5240 24"

(61 cm)

**34" to 35"

(86.4 cm to 88.9 cm)

⁄8"

(60.7 cm)

⁄4" to 34

⁄4"

(85.7 cm to 88.3 cm)

⁄32"

(60.2 cm)

⁄32"

(66.6 cm)

⁄32"

(99.5 cm)

Figure 9

Figure 9a

* Depth dimension of rough-in opening may vary depending on each individual installation. To recess entire

drawer "F" dimension plus 1" (2.5 cm) for thickness of power cord plug is required.

** Minimum rough-in opening required is to be larger than the adjusted height of the cabinet.

PRODUCT DIMENSIONS

Figure 10

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent

cabinet and the power cord routed through this

hole to a power outlet. Another way to increase

the available opening depth is to recess the power

outlet into the rear wall to gain the thickness of the

power cord plug. Not all recessed outlet boxes will

work for this application as they are too narrow,

but a recessed outlet box equivalent to Arlington

#DVFR1W is recommended for this application,

(see Figure 10).

"D"

"E"

"F"

"G"

"H"

Floor mount anti-tip bracket.

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

VDUI5240

115V/60Hz/15A

130 lbs

(59 kg)

⁄2"

(54.6 cm)

(2.5 cm)

WARNING

Floor mount Anti-tip Bracket must be installed for

freestanding applications. Not required for built in

applications.

Figure 11

PRODUCT DIMENSIONS

# A grounded 15 amp dedicated circuit is required.

Follow all local building codes when installing

electrical and appliance.

Power Failure

ALARM RESET

Temp

Minus

keypad

Temp

Plus

keypad

On/Off

keypad

Display Area

Lock

keypad

System Status

indicators

Figure 12

Electronic single zone control

Starting your appliance:

Plug the appliance power cord into a 115 volt wall outlet.

Your appliance is shipped from the factory in the "On"

position and will begin start-up of cooling as soon as power

is supplied. If the appliance does not start, conﬁ rm that the

wall outlet has power, and that the control is in the "On"

position, (See "Turning your appliance On and Off" below).

The control display is covered with a clear plastic ﬁ lm. This

ﬁ lm may be removed by carefully lifting the ﬁ lm at a corner.

On initial power up, the control display will indicate a

"Power Failure" alarm. This is a normal condition as

the appliance was powered-up at the factory for quality

inspection and then removed from power. A momentary

press of the "On/Off" keypad will reset this alarm condition.

(See Alarms section on page 12).

Turning your appliance ON and OFF:

If the appliance is "On", (and out of sleep mode) the

temperature will be shown in the display area of the control.

To turn the appliance "Off", press and hold the "On/Off"

keypad for 4-seconds. "OFF" will now be displayed on the

control.

To turn the appliance "On", press and hold the "On/Off"

keypad for 4-seconds.

Sleep mode:

If no keypads are pressed for 60 seconds, the display will

enter sleep mode to conserve power. The control panel

will go dark with the exception of the system status "OK"

indicator which will remain enabled. Alarm conditions will

wake the display, (see alarms on page 12).

To make the following changes to the control

settings (turning the appliance ON/OFF, adjusting the

temperature, and activating vacation mode), the control

must be awake.

The sleep mode can be disabled if you prefer to have the

display on continuously. Press and hold the "Lock" keypad

until the display goes past "Loc" and reads "nSL". To

enable the sleep mode, repeat the instruction, again going

past "Loc" until the display reads "SLP".

To wake the display press any keypad. A conﬁ rm tone will

sound, and the current storage compartment temperature

will be displayed.

USING YOUR ELECTRONIC CONTROL

Temperature Sensor Error Codes

Sensor Displayed Code Error Description Action to Take

Single Zone

Temperature

Sensor

Failed temperature sensor in the single zone

compartment. Can lead to

unwanted storage temperatures and/or

spoiled perishable goods.

Call service to have the

temperature sensor replaced and

remove all perishable goods from

compartment to prevent spoilage.

Defrost Sensor

Failed defrost temperature sensor.

Causes unit to not defrost properly and can

create large frost build-up. Can lead to water

damage to the unit and

surrounding ﬂ oor.

Unplug the power cord

immediately and call service to

have the defrost sensor replaced.

The temperature sensors are monitored continuously.

Any OPEN or SHORTED circuit condition will initiate an

ERROR CODE as listed below:

Temperature Sensor Error Codes

Temperature mode:

The temperature mode is preset from the factory in

Fahrenheit (°F) but you have the option to change it to

Centigrade (°C). To change the mode, press and hold the

"-" keypad, while pressing the "+" keypad, then release the

"-" keypad.

The temperature will now be displayed in Centigrade (°C).

Repeat the procedure to change the temperature mode

back to Fahrenheit (°F).

Control lock:

The control panel can be locked to avoid unintentional

changes. To lock the control, press and hold the "Lock"

keypad until the display reads "Loc" then immediately

release your ﬁ nger from the keypad. The lock icon will ﬂ ash

3-times and then continuously illuminate. When the control

panel is locked, only the Lock keypad, System Status OK

indicator , and the Alarm indicator are active. To un-lock

the control panel, repeat this instruction until the display

reads "nLc" then immediately release your ﬁ nger from the

keypad.

Adjusting the temperature:

To set or check the set-point temperature (with the

control out of sleep mode), press the "-" or "+" keypads.

"SET" will be indicated on the user interface panel and

the current set-point temperature will display and ﬂ ash.

Subsequent presses of the "-" or "+" keypads will adjust

the temperature colder or warmer respectively. When you

have reached your desired set-point temperature, press

the "On/Off" keypad to accept, or do nothing and the "Set"

mode will time-out in 10-seconds accepting the displayed

temperature as the new set-point.

The available set-point temperature range for your

appliance is 34°F (1.2°C) to 42°F (5.7°C). If you attempt to

adjust the temperature outside of this range you will receive

an audible notiﬁ cation.

When initially loading your product with warm contents,

it may take up to 48-hours for the storage compartment

temperature to stabilize.

When making temperature set-point changes, it may take

up to 24-hours for the stored contents to stabilize at your

new set-point temperature.

Factors that affect the storage compartment stabilized

temperature:

• Changes to temperature setting.

• Room temperature changes.

• Temperature of stored contents.

- Loading warm contents.

- Cold content load will delay the change to a warmer

set-point temperature.

- Warm content load will delay the change to a colder

set-point temperature.

• Usage, (number and duration of the drawer openings).

• Installation of the appliance in direct sunlight or next to

a heat source.

USING YOUR ELECTRONIC CONTROL

NOTE

If the control lock is active (illuminated lock icon) the

control will have to be unlocked before using the

keypad to reset an alarm condition. See page 11

(Control Lock) for instructions for unlocking the control.

ALARM RESET

Power Failure

ALARM RESET

Temp

NOTE

Door Ajar

Temp

Door Ajar

ALARM RESET

This alarm condition can be reset by momentarily pressing

the "On/Off" keypad. If this alarm occurs it is recommended

that you check the condition of your stored contents,

even though the appliance is operating normally and the

temperature has recovered, as prolonged temperature

excursions could spoil perishables.

USING YOUR ELECTRONIC CONTROL

• Power failure - If power to the appliance is inter-

rupted the System Status indicator will turn-off and

the "Power Failure" indicator will ﬂ ash. Additionally,

an "ALARM RESET" indicator will be displayed below

the "On/Off" keypad. No audible tone will sound.

This alarm condition can be reset by momentarily

pressing the "On/Off" keypad. If this alarm occurs, it

is recommended that you check the condition of any

perishables, even if the appliance is operating normally

and the temperature has recovered, as prolonged

power outages could result in excessive temperature

excursions which may spoil perishables.

• Temperature alarm - If the storage compartment

temperature deviates excessively from your set-

point temperature for an extended period of time, the

"TEMP" indicator will ﬂ ash, and an audible tone will

sound every 60 seconds. Additionally, an "ALARM

RESET" indicator will be displayed below the "ON/

OFF" keypad.

Multiple alarms are possible, i.e.- "Door Ajar" for a

prolonged period may trigger a "Temp" alarm, in which case

both "Door Ajar" and "Temp" indicators will activate.

Alarms:

The control will alert you to conditions that could adversely

affect the performance of the appliance.

• Door ajar - If a drawer is open, or not closed

properly, for more than 5-minutes the System Status

OK indicator will turn-off, the "Door Ajar" indicator

will ﬂ ash, and a tone will sound every 60 seconds.

Additionally, an "ALARM RESET" indicator will be

displayed below the "On/Off" keypad.

This alarm condition can be reset by closing the drawer or

momentarily pressing the "On/Off" keypad, (i.e.-if you are

cleaning the storage compartment, etc.). The alarm will

recur in 5-minutes if the alarm condition persists.

NOTE

The audible alarm can be muted, for each occurrence, by

pressing the lock keypad.

NOTE

The audible alarm can be muted, for each occurrence,

by pressing the lock keypad.

NOTE

After a high temperature alarm condition, check all

perishables to ensure they are safe for consumption.

The temperature alarm may occur as a result of high

usage or introduction of warm contents to the storage

compartment. If the temperature alarm continues to occur,

your unit may require service.

CAUTION

To enter Vacation Mode (with the control out of sleep

mode), press and hold the "On/Off" keypad until the display

goes past "OFF" and reads "VAC". The display will ﬂ ash

"VAC" 3-times to acknowledge your request, then will

display "VAC" continuously until Vacation mode is exited.

A power outage will not exit Vacation mode, exiting can

only be accomplished manually. To exit Vacation mode and

return to normal operation, press and hold the "On/Off"

keypad until the control displays the temperature.

Vacation mode:

This operating mode can be used to save energy during

high cost energy periods, or when you won't be using your

appliance for an extended period of time by disabling the

lights, alarm tones, and keypad entry tones. Vacation mode

also serves as a Sabbath mode, disabling functions and

its controls in accordance with the weekly Sabbath and

religious holidays observed within the Orthodox Jewish

community. When used as Sabbath mode, you may open

or close a drawer at any time to access contents without

concern of directly turning on or off any lights, digital

readouts, solenoids, fans, valves, compressor, icons, tones,

or alarms.

When activated, the display, alarm indicators and tones,

keypad touch tones, interior lights, and all options are

disabled. All keypad functions are disabled, with the

exception of the "On/Off" keypad which is required to exit

Vacationmode. Storage compartment temperatures are

monitored and controlled at the settings prior to entering

Vacation mode.

USING YOUR ELECTRONIC CONTROL

CARE AND CLEANING

Light assembly replacement

All models use an LED to illuminate the interior of the

appliance. This component is very reliable, but should it fail,

contact a qualiﬁ ed service technician for replacement of the

LED.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as

possible. Minimize the number of drawer openings while

the power is off so as not to adversely affect the appliance's

temperature.

Care of Appliance

1. Avoid leaning on the drawer, you may bend the drawer

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or

mopping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as

needed.

4. Periodically check and/or clean the front grille as

needed.

Front Grille

Be sure that nothing obstructs the required air ﬂ ow

openings in front of the cabinet. At least once or twice a

year, brush or vacuum lint and dirt from the front grille area

(see page 4).

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

Cabinet

The painted cabinet can be washed with either a mild soap

and water and thoroughly rinsed with clear water. NEVER

use abrasive scouring cleaners.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

The following suggestions will minimize the

cost of operating your refrigeration appliance.

1. Do not install your appliance next to a hot appliance

(cooker, dishwasher, etc.), heating air duct, or other

heat sources.

2. Install product out of direct sunlight.

3. Ensure the front grille vents at front of appliance

beneath drawer are not obstructed and kept clean to

allow ventilation for the refrigeration system to expel

heat.

4. Plug your appliance into a dedicated power circuit. (Not

shared with other appliances).

5. When initially loading your new product, or whenever

large quantities of warm contents are placed within

refrigerated storage compartment, minimize drawer

openings for the next 12 hours to allow contents to pull

down to compartment set temperature.

6. Maintaining a relatively full storage compartment

will require less appliance run time than an empty

compartment.

7. Ensure drawer closing is not obstructed by contents

stored in your appliance.

8. Allow hot items to reach room temperature before

placing in product.

9. Minimize drawer openings and duration of drawer

openings.

10. Use the warmest temperature control set temperature

that meets your personal preference and provides the

proper storage for your stored contents.

11. When on vacation or away from home for extended

periods, set the appliance to warmest acceptable

temperature for the stored contents.

12. Set the control to the “off” position if cleaning the

appliance requires the drawer to be open for an ex-

tended period of time.

ENERGY SAVING TIPS AND OBTAINING SERVICE

If service is required, call your authorized service agency.

Have the following information readily available:

• Model number

• Serial number

• Date purchased

• Name of dealer from whom purchased

Clearly describe the problem that you are having. If you are

unable to obtain the name of an authorized service agency,

or if you continue to have service problems, contact Viking

Range, LLC at (888) 845-4641 or write to:

VIKING RANGE, LLC

PREFERRED SERVICE

111 Front Street

Greenwood, Mississippi 38930 USA

Record the information indicated below. You will need it

if service is ever required. The serial number and model

numbers for your refrigerator are located on the upper wall,

behind the lighting:

Model No. ___________________________________

Serial No. _____________________________________

Date of Purchase ______________________________

Date Installed _________________________________

Dealer’s Name ________________________________

Address _____________________________________

__________________________________________

If service requires installation of parts, use only authorized

parts to insure protection under the warranty.

Keep this manual for future reference.

CAUTION

In the unlikely event you lose cooling in your unit, do not

unplug the product from the electric supply, but do call

a qualiﬁ ed service technician immediately. It is possible

that the loss of cooling capacity is a result of excessive

frost build-up on the evaporator cooling coil. In this case,

removing power to the unit will result in the melting of this

excessive quantity of ice, which could generate melt water

that exceeds the capacity of the defrost drain system and

could result in water damage to your home. The end-user

will be ultimately responsible for any water damage caused

by prematurely turning the unit off without appropriately

managing the excess water run-off.

• Never attempt to repair or perform maintenance on

the appliance until the main electrical power has been

disconnected. Turning the appliance control "OFF"

does not remove electrical power from the units wiring.

• Replace all parts and panels before operating.

WARNING

Electrocution Hazard

Before You Call for Service

If the appliance appears to be malfunctioning, read through

this manual ﬁ rst. If the problem persists, check the trouble-

shooting guide below. Locate the problem in the guide and

refer to the cause and its remedy before calling for service.

The problem may be something very simple that can be

solved without a service call. However, it may be required

to contact your dealer or a qualiﬁ ed service technician.

TROUBLESHOOTING

Problem Possible Cause Remedy

Appliance not cold enough

(See “Adjusting the temperature" on

page 11)

• Control set too warm

• Content temperature not

stabilized.

• Excessive usage or prolonged

drawer openings.

• Airﬂ ow to front grille blocked.

• Drawer gasket not sealing

properly.

• Adjust temperature colder. Allow

24 hours for temperature to

stabilize.

• Allow temperature to stabilize for

at least 24 hours.

• Airﬂ ow must not be obstructed to

front grille. See “clearances” on

page 4.

• Adjust or replace drawer gasket.

Appliance too cold

(See “Adjusting the Temperature” on

page 11)

• Control set too cold

• Drawer gasket not sealing

properly.

• Adjust temperature warmer.

Allow 24 hours for temperature to

stabilize.

• Adjust or replace drawer gasket.

No interior light. • Failed LED light assembly or light

switch.

• Contact a qualiﬁ ed service

technician.

Light will not go out when drawer is

closed

• Drawer not activating light switch.

• Failed light switch

• Appliance not level, level

appliance, (See page 4, “leveling

legs”)

• Contact a qualiﬁ ed service

technician.

Noise or Vibration • Appliance not level

• Fan hitting tube obstruction.

• Level appliance, see “Leveling

Legs” on page 4.

• Contact a qualiﬁ ed service

technician.

Appliance will not run. • Appliance turned off

• Power cord not plugged in.

• No power at outlet.

• Turn appliance on. See “Starting

your appliance” on page 10.

• Plug in power cord.

• Check house circuit.

HOUSEHOLD PRODUCT WARRANTY

REFRIGERATED DRAWERS WARRANTY

TWO YEAR FULL WARRANTY

Refrigerated drawers and all of their component parts, except as detailed below*†, are warranted to be free from defective materials or workmanship

in normal residential use for a period of two (2) years from the date of original retail purchase. Viking Range, LLC, warrantor, agrees to repair or replace,

at its option, any part which fails or is found to be defective during the warranty period.

*FULL NINETY (90) DAY COSMETIC WARRANTY: Product is warranted to be free from cosmetic defects in materials or workmanship (such

as scratches on stainless steel, paint/porcelain blemishes, etc.) for a period of ninety (90) days from the date of original retail purchase or

closing date for new construction, whichever period is longer. Any defects must be reported to the selling dealer within ninety (90) days from

date of original retail purchase. Viking Range, LLC uses high quality processes and materials available to produce all color ﬁ nishes. However,

slight color variation may be noticed because of the inherent differences in painted parts and porcelain parts as well as differences in kitchen

lighting, product locations, and other factors. Therefore, this warranty does not apply to color variation attributable to such factors.

†FULL NINETY (90) DAY WARRANTY IN “RESIDENTIAL PLUS” APPLICATIONS: This full warranty applies to applications where use

of the product extends beyond normal residential use, but the warranty period for products used in such applications is ninety (90) days.

Examples of applications covered by this warranty are bed and breakfasts, ﬁ re stations, private clubs, churches, yachts, etc. Under this

“Residential Plus” warranty, the product, its components and accessories are warranted to be free from defective material or workmanship

for a period of ninety (90) days from the date of original retail purchase. This warranty excludes use of the product in all commercial locations

such as restaurants, food service locations and institutional food service locations.

SIX YEAR FULL WARRANTY ON SEALED REFRIGERATION PARTS AS LISTED

Any sealed refrigeration system component, as listed below, is warranted to be free from defective materials or workmanship in normal household use

during the third through the sixth year from the date of original retail purchase. Viking Range, LLC, warrantor, agrees to repair or replace, at its option,

any part which fails or is found to be defective during the warranty period.

Sealed Refrigeration System Components: Compressor, Evaporator, Condenser, Connecting Tubing, Dryer/Strainer

TWELVE YEAR LIMITED WARRANTY ON SEALED REFRIGERATION PARTS AS LISTED

Any sealed refrigeration system component, as listed above, which fails due to defective materials or workmanship in normal household use during the

seventh through the twelfth year from the date of original retail purchase will be repaired or replaced, free of charge for the part itself, with the owner

paying all other costs, including labor.

TERMS AND CONDITIONS

This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of the product during the term of

the warranty and applies to products purchased and located in the United States, Canada, Mexico and the Caribbean (excluding Cuba, Dominican

Republic, and Haiti). Products must be purchased in the country where service is requested. If the product or one of its component parts contains a

defect or malfunction during the full warranty period after a reasonable number of attempts by the warrantor to remedy the defect or malfunction, the

owner is entitled to either a refund or replacement of the product or its component part or parts. Replacement of a component part includes its free

installation, except as speciﬁ ed under the limited warranty. Under the terms of this warranty, service must be performed by a factory authorized Viking

Range, LLC service agent or representative. Service will be provided during normal business hours, and labor performed at overtime or premium rates

shall not be covered by this warranty.

Owner shall be responsible for proper installation, providing reasonable and necessary maintenance, providing proof of purchase upon request, and

making the appliance reasonably accessible for service. The return of the Owner Registration Card is not a condition of warranty coverage. You should,

however, return the Owner Registration Card so that Viking Range, LLC can contact you should any question of safety arise which could affect you.

This warranty gives you speciﬁ c legal rights, and you may also have other rights which may vary from jurisdiction to jurisdiction.

WHAT IS NOT COVERED BY THIS WARRANTY: This warranty shall not apply to damage resulting from abuse, failure to provide reasonable and

necessary maintenance, accident, delivery, negligence, natural disaster, loss of electrical power to the product for any reason, alteration, outdoor use,

improper installation, improper operation, or repair or service of the product by anyone other than an authorized Viking Range, LLC service agency or

representative. This warranty does not apply to commercial usage.

LIMITATION OF REMEDIES AND DURATION OF IMPLIED WARRANTY

OWNER’S SOLE AND EXCLUSIVE REMEDY FOR A CLAIM OF ANY KIND WITH RESPECT TO THIS PRODUCT SHALL BE THE REMEDIES

SET FORTH ABOVE. VIKING RANGE, LLC IS NOT RESPONSIBLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGE, INCLUDING BUT NOT

LIMITED TO FOOD OR MEDICINE LOSS, DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF

CONTRACT OR OTHERWISE. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusions may not apply to you. ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

APPLICABLE TO THIS PRODUCT ARE LIMITED IN DURATION TO THE PERIOD OF COVERAGE OF THE APPLICABLE EXPRESS WRITTEN

LIMITED WARRANTIES SET FORTH ABOVE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may

not apply to you.

WARRANTY SERVICE

To obtain warranty service, contact an authorized Viking Range, LLC service agent, or Viking Range, LLC, 111 Front Street, Greenwood, Mississippi

38930, (888) 845-4641. Provide model and serial number and date of original purchase or closing date for a new construction. For the name of your

nearest authorized Viking Range, LLC service agency, call Viking Range, LLC.

IMPORTANT: Retain proof of original purchase to establish warranty period.

Speciﬁ cations subject to change without notice.

058187-000B EN

Viking Range, LLC

111 Front Street

Greenwood, Mississippi 38930 USA

(662) 455-1200

For product information,

call 1-888-(845-4641)

or visit our web site at vikingrange.com

(030118)

Install / Use & Care

MANUAL

5 SERIES

Refrigerated Drawers

Tiroirs Réfrigérés

Gavetas Refrogeradas

CVDUI52 40

FR-D’installation/d’utilisation et d’entretien

ES-De instalación/operación y mantenimiento

2-FR

REMARQUE

ATTENTION

Importantes instructions de sécurité

Les avertissements et les instructions de sécurité qui ap-

paraissent dans ce guide n’ont pas la prétention de couvrir

toutes les conditions et situations possibles pouvant arriver.

Il faut faire preuve de bon sens, de précautions et de soins,

pour installer, utiliser ou entretenir cet appareil.

Reconnaissance des symboles,

des mots et des étiquettes

concernant la sécurité.

ATTENTION - Risques ou pratiques dangereuses

pouvant entraîner des blessures individuelles, des dégâts

matériels ou des dommages au produit.

REMARQUE - Information importante pour réaliser une

installation et une utilisation sans problèmes.

Contenu :

Informations de sécurité.......................................................2

Déballage de votre appareil ..................................................3

Enregistrement de la garantie ......................................3

Installation de votre appareil ..............................................4

Dégagements par rapport à l’armoire .............................4

Mise à niveau de l’appareil .............................................4

Raccordement électrique.................................................5

Installation du dispositif anti-basculement..........................6

Dimensions du produit.......................................................8

Utilisation de votre commande électronique ....................10

Démarrage de votre appareil ........................................10

Mode veille ...................................................................10

Mise en marche et arrêt de votre appareil .....................10

Réglage de la température ............................................11

Mode température ........................................................11

Verrouillage des commandes ........................................11

Codes d’erreur des capteurs de température ..............11

Alertes...........................................................................12

Porte entrouverte .......................................................12

Panne de secteur ......................................................12

Alerte de température ...............................................12

Mode vacances ............................................................13

Entretien et nettoyage ......................................................13

Conseils pour l’économie d’énergie ................................14

Obtention de service ........................................................14

Dépannage................................................................15

Garantie...........................................................................16

CONTENU

AVERTISSEMENT - Risque possible de décès ou

de blessure grave si vous ne suivez pas les instructions.

AVERTISSEMENT

Avertissements de la proposition 65 de l'État de Californie

: Ce produit contient au moins un produit chimique connu par

l’État de Californie pour être à l’origine de cancers.

AVERTISSEMENT

Avertissements de la proposition 65 de l'État de Californie

: Ce produit contient au moins un produit chimique connu par

l’État de Californie pour être à l’origine de malformations et

autres déﬁ ciences de naissance.

AVERTISSEMENT

La page charge ...

Viking Range VDUI5240DSS Manuel utilisateur

Marque: Viking Range

Modèle: VDUI5240DSS

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Viking Range VDUI5240DSS User manual
español: Viking Range VDUI5240DSS Manual de usuario

Viking Range VDUI5240DSS Manuel utilisateur

Viking Range VDUI5240DSS Manuel utilisateur

dans d''autres langues

Autres documents