Sub-Zero 5310823 Manuel utilisateur

Taper
Manuel utilisateur
CLASSIC REFRIGERATION
USE AND CARE GUIDE
CLEANING, MAINTENANCE, AND MORE
2 | Sub-Zero Customer Care 800.222.7820
CLASSIC REFRIGERATION
Customer Care
The model and serial number are printed on the enclosed
product registration card. Both numbers are also listed on
the product rating plate. Refer to page 3 for rating plate
location. For warranty purposes, you will also need the date
of installation and name of your authorized Sub-Zero dealer.
Record this information below for future reference.
SERVICE INFORMATION
Model Number
Serial Number
Date of Installation
Certied Service Name
Certied Service Number
Authorized Dealer
Dealer Number
If your product ever needs attention, be sure to use a
Sub-Zero Factory Certied Service provider recommended
by our Customer Care Center, or select one from our list of
providers available at subzero.com/locator. All Factory Certi-
ed Service providers are carefully selected and thoroughly
trained by us.
Important Note
To ensure this product is installed and operated as safely
and efciently as possible, take note of the following types
of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specied.
Contents
3 Classic Features
4 Electronic Controls
5 Storage
8 Operation
12 Care Recommendations
14 Technical Data
15 Troubleshooting
19 Sub-Zero Warranty
WARNING
PROPOSITION 65 FOR CALIFORNIA RESIDENTS
Cancer and Reproductive Harm—
www.P65Warnings.ca.gov
subzero.com | 3
Classic Features
FEATURES
1
Product Rating Plate
2
Electronic Control Panel and Display
3
Freshness Cards
4
Door Shelves
5
Dairy Compartment
6
Refrigerator Storage Drawers
7
High-Humidity Crisper Drawer
8
Glass Shelves
9
Freezer Baskets
10
Ice Container
11
Air Purication System
12
Water Filtration System (behind grille)
13
Automatic Ice Maker
14
Ice and Water Dispenser (dispenser models)
15
Condenser (behind grille)
CLASSIC FEATURES
Over-and-under model
1
8
3
9
15
13
7
11
Side-by-side model with internal dispenser
2
6
12
5
4
10
2
8
3
6
15
9
10
13
1
4
12
5
14
7
11
4 | Sub-Zero Customer Care 800.222.7820
ELECTRONIC CONTROLS
Control Panel
FUNCTION
LIGHTS Turns the interior accent lighting on or off for glass
door models.
ICE MAKER Turns power to the ice maker on or off. Use to dis-
able the ice maker during extended vacations.
MAX ICE Activates or deactivates the max ice feature which
increases ice production 30% for a 24-hour period.
COLDER
WARMER
Adjusts the tem per ature in one-degree increments.
Combination units have separate temperature con-
trols for the refrigerator and freezer. Temper atures
are preset at 38°F
(3°C) and 0°F (-18°C).
PURE AIR Activates or deactivates the air purication system.
ALARM Activates or deactivates the door alarm. A chime
indicates the door has been left ajar for more than
60 seconds.
POWER Turns the unit on or off. When the power is off,
“OFF” appears in the control panel display. Turning
the power off at the control panel eliminates the
need to unplug or turn the power off at the circuit
breaker during service or extended vacations.
Control panel and display (model BI-30UG shown)
Display
INDICATOR
Illuminates or ashes when the electronic control system
detects a temperature or ice maker problem, or if the
condenser needs to be cleaned.
Illuminates when the air purication system is activated,
and ashes when the cartridge needs to be replaced.
After the cartridge has been replaced, touch and hold
PURE AIR on the control panel for 5 seconds to reset.
Illuminates when the water lter needs to be replaced.
Illuminates when the ice maker system is activated.
Illuminates when the max ice feature is activated.
Illuminates when the door alarm is activated.
Illuminates when the accent lighting is activated for glass
door models.
subzero.com | 5
Keeping Food At Its Best
DUAL REFRIGERATION
®
This Sub-Zero features a unique Dual Refrigeration
®
system
to keep food fresher longer.
With the Sub-Zero Dual Refrigeration
®
system, individual
refrigerator and freezer systems have been designed to
maintain accurate, consistent temperatures and proper
humidity levels for longer food life expectancy. Dual Refrig-
eration
®
eliminates transfer of fresh food odors to frozen
food and ice and does not freeze the moisture out of the air
in the fresh food section.
For handy tips and information on how to maximize food
freshness, refer to the freshness cards stored in the
refrigerator.
STORAGE
Refrigerator Storage
DOOR SHELVES
To remove a door shelf or the dairy compartment, lift from
the bottom and slide out. To reinstall, place in the desired
position and slide the shelf down onto the guides. Refer to
the illustration below.
IMPORTANT NOTE: If the door opening is limited to 90°,
door shelves may need to be removed before removing a
storage drawer or glass shelf.
Door shelf removal
6 | Sub-Zero Customer Care 800.222.7820
STORAGE
GLASS SHELVES
To remove or adjust a glass shelf, tilt up, then lift up and out.
To reposition, insert the shelf in the tracks along the back
wall, then lower the front until it locks into position. Refer to
the illustration below.
IMPORTANT NOTE: Use care when handling glass shelves to
prevent breakage or scratching the interior.
CAUTION
Glass shelves should warm to room temperature before
immersing in warm water.
Glass shelf removal
Refrigerator Storage
STORAGE DRAWERS
To remove a storage drawer, pull forward until the drawer
stops. Lift the front of the drawer slightly, then pull forward.
Refer to the illustration below.
For French door models, the drawer slides may need to be
pushed back manually to provide sufcient clearance for
removal.
To reinstall, push the drawer slides in. Align the drawer with
the slides and push back until it stops. Press down on the
front of the drawer to engage the slides.
Storage drawer removal
subzero.com | 7
ICE CONTAINER
BI-36F and over-and-under models: To remove, pull the
container forward until it stops, then lift out.
Side-by-side models: To remove, pull the container forward
until it stops, then lift to clear the carrier assembly along the
back. Pull forward and out. Refer to the illustration below.
Dispenser models: To remove, pull the container out par-
tially, then rotate and pull out. Refer to the illustration below.
STORAGE
Freezer Storage
FREEZER BASKETS
BI-36F and side-by-side models: To remove, pull forward
until the basket stops. Pull the two metal clips located
behind the bottom two corners of the basket forward, then
lift up and out. Refer to the illustration below. To reinstall,
push the drawer slides in. Align the basket with the slides
and push back until it stops. Press down on the front of the
basket to engage the slides.
IMPORTANT NOTE: For models BI-36S, BI-42S, BI-42SID,
and BI-42SD, to remove, the freezer basket must be raised
and pulled through the opening in the door liner after
disengaging.
Over-and-under models: To remove the upper and lower
freezer baskets, lift up and out. Refer to the illustration
below. To reinstall, insert the lower basket into the four
corner retainers. Position the upper basket onto the side
rails and slide back until it clicks.
BI-36F and side-by-side models
Over-and-under models
Side-by-side models
Dispenser models
8 | Sub-Zero Customer Care 800.222.7820
AIR PURIFICATION CARTRIDGE REPLACEMENT
1 To access the air purication cartridge, grasp the outside
cover from the bottom and rotate upward. Refer to the
illustration below.
2 Grasp the black cover from the top and rotate down-
ward. The cartridge will pop out and can be removed.
3 Remove the new cartridge from packaging and insert
with the connector pointing downward.
4 Once in position, close the black cover. Then rotate the
outside cover downward until it closes against the back
wall.
5 Once the cartridge has been replaced, touch and hold
PURE AIR on the control panel for ve seconds to reset.
The
indicator will appear in the control panel display
but not ash.
Air Purication System
Many fresh foods emit ethylene gas, a naturally-occurring
compound that hastens food ripening and spoilage. The
air purication cartridge has been factory installed and is
located inside the refrigerator, on the back wall.
To initiate air purication, touch PURE AIR on the control
panel.
The cartridge will last approximately one year. The
indicator will ash in the control panel display when the
cartridge needs to be replaced.
Replacement Sub-Zero air purication cartridges can be
ordered online at subzero.com/store. For questions, contact
Sub-Zero Customer Care at 800-222-7820.
CAUTION
The air purication system complies with applicable
Federal requirements regarding incidental exposure
to ultraviolet light. Lamp contains mercury. Manage in
accordance with disposal laws. Visit earth911.com or
call 800-222-7820.
OPERATION
Air purication cartridge
subzero.com | 9
OPERATION
WATER FILTER REPLACEMENT
1 To access the water lter, pull out on the bottom edge
of the grille assembly and rotate upward.
2 To remove the old lter, rotate counterclockwise one-
quarter turn, then pull out. Refer to the illustration below.
It is normal for a small amount of water to drip when
the lter is removed. It should be wiped up with a paper
towel or cloth.
3 Remove the new lter from packaging and remove the
plastic cap.
4 Insert the new lter into the manifold and turn clockwise.
5 Once the new lter has been installed, press and hold
the water lter reset button for ve seconds to reset.
Refer to the illustration below.
Water Filtration System
The water ltration system of Sub-Zero Classic models
supplies ltered water to the ice maker and water dispenser
(dispenser models) to produce great-tasting water and ice.
IMPORTANT NOTE: When using the water ltration system
for the rst time and after lter replacement, it is neces-
sary to clear any air from the system and allow the lter to
assist in cleaning the water lines. For non-dispenser models,
discard the rst two full containers of ice. For dispenser
models, dispense several glasses of water for a period of
two minutes.
If the water ltration system will not be used, it can be
placed in water lter bypass mode by removing the lter.
The lter is rated for 750 gallons
(2839 L) or one year, which-
ever comes rst. The
indicator will illuminate in the
control panel display when the lter needs to be replaced.
Replacement Sub-Zero water lters can be ordered online
at subzero.com/store. For questions, contact Sub-Zero
Customer Care at 800-222-7820.
Water lter removal
WATER FILTER
Water lter location
WATER FILTER
RESET BUTTON
WATER
FILTER
10 | Sub-Zero Customer Care 800.222.7820
OPERATION
Ice and Water Dispenser
The rst time the water dispenser is used, purge the water
system and storage tank for three minutes. This will clear
any air in the system, along with impurities from new
plumbing connections.
Initially, for water to dispense properly, press and hold
WATER or the water dispenser button until water ows from
the dispenser. It may need to be pressed for 60 seconds for
water to ll the internal reservoir tank.
The chilled water reservoir tank holds approximately 40 oz
(1.2 L) of ltered water. It may take several hours to chill the
water to refrigerator temperature during the original ll and
after a large amount of water is dispensed.
CAUTION
Limit continuous ice and water dispenser operation to
seven minutes or less.
Ice Maker Operation
To initiate ice production, touch ICE MAKER on the control
panel. After initial start-up, discard the rst few batches
of ice. The ice may contain impurities from new plumbing
connections.
The ice maker will cycle every two hours. If ice is not used
regularly it may fuse together. To avoid, discard ice and
allow ice maker to replenish.
Sabbath
This appliance is certied by Star-K to meet strict religious
regulations in conjunction with specic instructions found
on www.star-k.org.
To initiate Sabbath mode, while the unit is on, touch POWER
on the control panel. “OFF” appears in the control panel
display. Touch and hold POWER for 10 seconds until “SAb”
appears in the display indicating Sabbath mode has been
initiated. Lights, ice maker, door alarm, and dispenser (if
applicable) will be disabled. To return to normal operating
conditions, touch POWER.
subzero.com | 11
Ice and Water Dispenser
INTERNAL DISPENSER
For models BI-42SID and BI-48SID, the internal ice and
water dispenser is designed to accommodate a 16-oz
(.5 L)
pint glass. Larger containers may be used but may compro-
mise the effectiveness of the dispenser. Drops of water may
collect in the removable water grille located directly below
the dispenser. Refer to the illustration below.
FUNCTION
ICE Press and hold to dispense ice.
WATER Press and hold to dispense water.
For models with an internal water only dispenser, the
dispenser is located inside the refrigerator on the left wall.
Press a glass against the dispenser to activate water ow.
Water ow will stop when the glass is pulled away. Refer to
the illustration below.
EXTERNAL DISPENSER
Drops of water may collect in the removable water grille.
This is not a drain. Do not pour water into the water grille.
For large quantities of ice, a bulk ice dispenser is located
inside the refrigerator. Refer to the illustrations below.
FUNCTION
LIGHT Press to cycle through lighting options; lights off,
lights on, and control panel lights only.
ICE Press and hold to dispense ice.
WATER Press and hold to dispense water.
LOCK Press and hold for 3 seconds to activate or deac-
tivate the dispenser lock. The lock indicator will be
illuminated when dispenser is locked.
BULK ICE Press and hold to dispense large quantities of ice.
OPERATION
WATER
ICE
WATER
GRILLE
WATER DISPENSER
Internal ice and water
dispenser
Internal water dispenser
GRILLE
TRAY
BULK ICE
Removable water grille
Bulk ice dispenser
12 | Sub-Zero Customer Care 800.222.7820
Interior Lighting
For glass door models, accent lighting can be turned on
and off by touching LIGHTS on the control panel. The
indicator illuminates when accent lighting is activated.
Cleaning
STAINLESS STEEL EXTERIOR
Use a nonabrasive stainless steel cleaner and apply with
a soft lint-free cloth. To bring out the natural luster, lightly
wipe the surface with a water-dampened microber cloth
followed by a dry polishing chamois. Always follow the grain
of stainless steel.
CARE RECOMMENDATIONS
subzero.com | 13
CONDENSER CLEANING
CAUTION
Before cleaning the condenser, turn power off at the
control panel. Wear gloves to avoid injury from sharp
condenser ns.
The condenser is located behind the ip-up grille. To
access, pull out on the bottom edge of the grille and rotate
upward. Use a soft bristle brush and vacuum to remove
dust and lint from the condenser. Clean the condenser every
6–12 months. Refer to the illustration below.
IMPORTANT NOTE: To avoid damaging the condenser ns,
vacuum in the direction of the ns.
CAUTION
Failure to clean the condenser could result in tempera-
ture loss, mechanical failure, or damage.
CARE RECOMMENDATIONS
Cleaning
INTERIOR CLEANING
For over-and-under and side-by-side models, the refrig-
erator or freezer may be disabled without disrupting the
other section. To disable a section, touch POWER. Touch
and hold WARMER for the section being disabled, continue
to hold and touch POWER. Double dashes will appear in the
control panel display. Repeat to turn the section back on.
To clean interior surfaces and all removable parts, wash with
a mild solution of soap, water, and baking soda. Rinse and
dry thoroughly. Avoid getting water on the lights and control
panel.
CAUTION
Do not use vinegar, rubbing alcohol, or other alcohol-
based cleaners on any interior surface.
VACATIONS
For extended vacations, turn power off at the control panel.
Empty the unit and block doors open slightly to let fresh
air in and keep the interior dry. The water lter should be
replaced before start-up.
Condenser location
CONDENSER
14 | Sub-Zero Customer Care 800.222.7820
TECHNICAL DATA
Sub-Zero Water Filtration System Data
IMPORTANT NOTICE: Read this Performance Data Sheet carefully and compare the capabilities of this unit with your actual water treatment needs.
It is recommended that, before purchasing a water treatment unit, you have your water supply tested to determine your actual water treatment needs.
The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit
for water leaving the system, as specied in NSF/ANSI 42/53.
System tested and certied by NSF International against NSF/ANSI Standard 42 and 53 for the reduction of substances listed below.
Contaminant
Reduction*
Average Inuent
Concentration
NSF Specied
Challenge
Concentration
Average
% Reduction
Product Water Concentration
NSF Reduction
Requirements
NSF Test
ReportAverage Max Permissable
Chlorine, Taste & Odor 2.0 mg/L 2.0 mg/L ± 10% 97.5% 0.05 mg/L N/A ≥50% J-00056501
Normal Particulate
Class I, ≥0.5 to <1.0 μm
13,666,667
pts/ml
At least 10,000
particles/ml
98.9% 143,333 pts/ml N/A ≥85% J-00056506
Asbestos 96 MF/L 10
7
to 10
8
bers/L
>99% <1 MF/L N/A ≥99% J-00056511
Atrazine 0.010 mg/L 0.009 mg/L ± 10% 89.3% 0.001 mg/L 0.003 mg/L N/A J-00056512
Benzene 0.014 mg/L 0.015 mg/L ± 10% 96.3% 0.005 mg/L 0.005 mg/L N/A J-00056535
Carbofuran 0.08 mg/L 0.08 mg/L ± 10% 86.6% 0.01 mg/L 0.04 mg/L N/A J-00056537
Cyst** 122,500 cysts/L Min 50,000 cysts/L 99.99% 1 cyst/L N/A ≥99.99% J-00056513
Lead at pH 6.5 0.153 mg/L 0.15 mg/L ± 10% 99.3% 0.001 mg/L 0.010 mg/L N/A J-00056515
Lead at pH 8.5 0.150 mg/L 0.15 mg/L ± 10% 99.3% 0.001 mg/L 0.010 mg/L N/A J-00058784
Lindane 0.002 mg/L 0.002 mg/L ± 10% 97.8% 0.00004 mg/L 0.0002 mg/L N/A J-00058969
Mercury at pH 6.5 0.006 mg/L 0.006 mg/L ± 10% 95% 0.0003 mg/L 0.002 mg/L N/A J-00058785
Mercury at pH 8.5 0.006 mg/L 0.006 mg/L ± 10% 88% 0.0007 mg/L 0.002 mg/L N/A J-00058783
Toxaphene 0.015 mg/L 0.015 mg/L ± 10% 93.2% 0.001 mg/L 0.003 mg/L N/A J-00056531
Turbidity 10.8 NTU 11 ± 1 NTU 98.7% 0.153 NTU 0.5 NTU N/A J-00058972
P-Dichlorobenzene 0.215 mg/L 0.225 mg/L ± 10% 99.7% 0.0005 mg/L 0.075 mg/L N/A J-00056538
*Contaminant reduction determined by NSF testing. **Based on the use of Cryptosporidium Parvum oocysts.
Fibers greater than 10 μm in length.
APPLICATION GUIDELINES / WATER SUPPLY PARAMETERS
Capacity: certied for up to 750 gallons
(2,839 L); up to twelve months
Service Flow: 0.78 gpm
(2.95 Lpm)
Water Supply: potable water
Water Pressure: 35–120 psi
(2.8–8.2 bar)
Water Temperature: 40°F–100°F (5°C–40°C)
SPECIAL NOTES
Replacement Sub-Zero water lter cartridges can be ordered online at subzero.com/store, or contact customer care at 800-222-7820.
It is recommended that the lter cartridge be replaced when the indicator is displayed, if there is a noticeable drop in pressure, the ice cubes
become hollow, or every 12 months, whichever comes rst. Replacement lter pricing information can be found at subzero.com/store.
This lter must be installed, operated, maintained and replaced as required in order for the product to perform as advertised.
Note that while the testing was performed under standard laboratory conditions, actual performance may vary. The contaminants or other
substances removed or reduced by this water treatment system are not necessarily in your water.
Manufactured for: Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744, 800-222-7820
subzero.com | 15
TROUBLESHOOTING
Troubleshooting
SERVICE INDICATOR
Indicator illuminated: Touch POWER to turn the unit off.
Verify the condenser area is clean. Touch POWER to
turn the unit on. If the indicator is still illuminated, call
Sub-Zero Customer Care at 800-222-7820.
Indicator ashing: Contact Sub-Zero Factory Certied
Service.
Indicator ashing with chime: Contact Sub-Zero Factory
Certied Service.
Indicator ashing: Replace the air purication cartridge.
Also, replace the cartridge if there is an odor inside the
unit.
Indicator ashing: Replace the water lter. Also, replace
the lter if the ice tastes bad, is discolored, ice cubes are
small, or if the water ow from the dispenser is slow.
Indicator ashing with chime: The door has been left ajar
for more than 60 seconds. Close the door.
UNIT OPERATION
No lights or cooling.
Verify power is on.
Verify electrical power to the unit and home circuit
breaker is on.
No lights in the refrigerator or freezer.
The door/drawer may have been left ajar, which has
disabled lights to eliminate excess heat. If the lights are
out, close the door/drawer for one hour. If the lights are
still out, contact Sub-Zero Factory Certied Service.
LED interior lighting must be replaced by Sub-Zero
Factory Certied Service.
Frost, condensation, or ice buildup inside the unit.
Verify the condenser is clean.
Verify the door is closing properly.
Verify the door has not been left ajar.
Verify the door gasket does not have rips or tears. If it
does, contact Sub-Zero Factory Certied Service.
If icing is heavy, turn the unit off and use a hair dryer to
melt the ice. The hair dryer should be set on low and
kept moving at all times. Once the ice has melted, wipe
up any water with a cloth or paper towel.
High temperatures, the unit runs excessively or the unit is
giving off too much heat.
Verify the condenser is clean.
Verify the door is closing properly.
Verify the door has not been left ajar.
Increased ambient temperatures may cause the com-
pressors to run longer.
If the temperature display shows 38° and 0°, but is not
cooling, the unit may be in showroom mode. Contact
Sub-Zero Customer Care at 800-222-7820.
16 | Sub-Zero Customer Care 800.222.7820
Troubleshooting
ICE PRODUCTION
No ice.
Verify the
indicator appears in the control panel
display.
Verify the ice maker has been on for at least 24 hours.
Verify the freezer temperature is near 0°F.
Verify the ice container is properly installed.
Verify the ice maker arm is in the down position.
Verify water is being supplied to the unit.
Verify the water lter has been replaced within the last 12
months and is installed properly.
Verify the water lter has been removed if a reverse
osmosis ltration system is being used.
Verify the
indicator is not ashing. If it is ashing,
touch MAX ICE and ICE MAKER on the control panel
simultaneously.
Blue or green ice.
Possible copper supply line corrosion. Contact a
plumber to clean or replace.
Black ecks in the cubes.
Stop use and contact Sub-Zero Factory Certied
Service.
Bad taste.
Defrost the freezer and clean with soap and water.
Place coffee grounds or charcoal briquettes in the
freezer to absorb odor.
Hollow cubes.
Clean the condenser. Contact Sub-Zero Factory Certied
Service if unresolved.
TROUBLESHOOTING
ODOR
The unit should be cleaned before using for the rst time.
This will clear any odors that may have been trapped
during shipping.
Replace the air purication cartridge.
Clean the unit and shelving thoroughly.
Uncovered food could create an odor, which may require
cleaning.
Remove and clean the drain pan located behind the
kickplate, and reinstall.
subzero.com | 17
TROUBLESHOOTING
Troubleshooting
SERVICE
Maintain the quality built into your product by contacting
Sub-Zero Factory Certied Service. For the name of the
nearest Sub-Zero Factory Certied Service, check the
Support & Service section of our website, subzero.com
or call Sub-Zero Customer Care at 800-222-7820.
When contacting service, you will need the model and
serial number of your unit. Both numbers are listed on
the product rating plate. Refer to page 3 for rating plate
location.
For warranty purposes, you will also need the date
of installation and name of your authorized Sub-Zero
dealer. This information should be recorded on page 2
of this guide.
18 | Sub-Zero Customer Care 800.222.7820
Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf &
Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.
All other trademarks are property of their respective owners in the United States and other countries.
Sub-Zero Residential Limited Warranty
FOR RESIDENTIAL USE
FULL TWO YEAR WARRANTY*
For two years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, any part of the product that proves to be defec-
tive in materials or workmanship. All service provided by Sub-Zero under the above warranty must be
performed by Sub-Zero Factory Certied Service, unless otherwise specied by Sub-Zero, Inc. Service
will be provided during normal business hours.
FULL FIVE YEAR SEALED SYSTEM WARRANTY
For ve years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, these parts that prove to be defective in materials
or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided
by Sub-Zero under the above warranty must be performed by Sub-Zero Factory Certied Service, unless
otherwise specied by Sub-Zero, Inc. Service will be provided during normal business hours.
LIMITED TWELVE YEAR SEALED SYSTEM WARRANTY
For twelve years from the date of original installation, Sub-Zero will repair or replace the following parts
that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all
connecting tubing. If the owner uses Sub-Zero Factory Certied Service, the service provider will repair or
replace these parts with the owner paying for all other costs, including labor. If the owner uses non-certi-
ed service, the owner must contact Sub-Zero, Inc. (using the information below) to receive repaired or
replacement parts. Sub-Zero will not reimburse the owner for parts purchased from non-certied service
or other sources.
TERMS APPLICABLE TO EACH WARRANTY
The warranty applies only to products installed for normal residential use. The warranty applies only to
products installed in any one of the fty states of the United States, the District of Columbia or the ten
provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by
negligence, accident or improper use, maintenance, installation, service or repair.
THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC.
WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF
LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS,
IMPLIED OR STATUTORY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specic legal rights and you may also
have other legal rights that vary from state to state.
To receive parts and/or service and the name of Sub-Zero Factory Certied Service nearest you, contact
Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the Support & Service section of our website,
subzero.com, email us at [email protected] or call 800-222-7820.
*Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited
60-day parts and labor warranty for cosmetic defects.
*Replacement water lters and air purication cartridges are not covered by the product warranty.
2 | Atención al cliente de Sub-Zero 800.222.7820
REFRIGERACIÓN CLÁSICO
Contenido
3 Características clásico
4 Controles electrónicos
5 Almacenamiento
8 Operación
12 Recomendaciones de cuidado
14 Datos técnicos
15 Resolución de problemas
19 Garantía de Sub-Zero
ADVERTENCIA
PROPUESTA 65 PARA RESIDENTES DE CALIFORNIA
Cáncer y Daño Reproductivo—
www.P65Warnings.ca.gov
Atención al cliente
El modelo y número de serie están impresos en la tarjeta
de registro del producto adjunta. Los dos números también
aparecen en la placa de datos del producto. Consulte la
página 3 para encontrar la placa de datos. Para nes de la
garantía, usted también necesitará la fecha de instalación y
el nombre de su distribuidor autorizado de Sub-Zero.
Anote esta información abajo para referencia futura.
INFORMACIÓN PARA SERVICIO
Número de modelo
Número de serie
Fecha de instalación
Nombre de servicio certicado
Número de servicio certicado
Distribuidor autorizado
Número de distribuidor
Si su producto alguna vez necesita servicio, asegúrese de
usar un proveedor de servicios certicado por Sub-Zero
y recomendado por nuestro centro de atención al cliente,
o seleccione uno de nuestra lista de proveedores
disponibles en subzero.com/locator. Todos los proveedores
de servicio certicados de fábrica han sido cuidadosamente
seleccionados y entrenados a fondo por nosotros.
Aviso importante
Para garantizar que este producto sea instalado y operado
de la forma más segura y eciente posible, tome nota de los
siguientes tipos de información resaltada en esta guía:
AVISO IMPORTANTE resalta la información que es
especialmente importante.
PRECAUCIÓN indica una situación en la que se pueden
sufrir heridas leves o provocar daños al producto si no se
siguen las instrucciones.
ADVERTENCIA indica peligro de que se produzcan heridas
graves o incluso la muerte si no se siguen las precauciones.
AVISO IMPORTANTE: En toda esta guía, las dimensiones
entre paréntesis son milímetros, a menos que se especique
lo contrario.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Sub-Zero 5310823 Manuel utilisateur

Taper
Manuel utilisateur