Homelite UT21006 Manuel utilisateur

Marque: Homelite

Modèle: UT21006

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

Trimmer UT21006

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

26CC

String Trimmers

TAILLE-BORDURES À LIGNE

26 CC

RECORTADORAS DE HILO

26 CC

ALL VERSIONS

TOUTES LES VERSIONS

TODAS LAS VERSIONES

26CS

UT21006/UT29007

26SS

UT21046/UT29047

Cette taille-bordures à ligne a été conçue et fabriquée conformément

aux strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation de Homelite. Correctement entretenue, elle vous donnera

des années de fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre le

manuel d’utilisation avant d’employer ce produit.

Merci d’avoir acheté un produit Homelite.

Your string trimmer has been engineered and manufactured to Homelite’s high standard for dependability, ease of operation,

and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before

using this product.

Thank you for buying a Homelite product.

Su recortadora de hilo ha sido diseñada y fabricada de

conformidad con las estrictas normas de Homelite para brindar

fiabilidad, facilidad de uso y seguridad para el operador. Con el

debido cuidado, le brindará muchos años de sólido y eficiente

funcionamiento.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador antes

de usar este producto.

Le agradecemos la compra de un producto Homelite.

SAVE THIS MANUAL FOR FUTURE REFERENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner

toutes les figures mentionnées dans le manuel

d’utilisation.

Consulte esta sección desplegable para ver todas

las figuras a las que se hace referencia en el

manual del operador.

iii

A - Dual line string head (tête de cordon à ligne double, cabezal del hilo doble)

B - Drive shaft housing (logement d’arbre moteur, alojamiento del eje de impulsión)

C - Front handle (poignée avant, mango delantero)

D - Rear handle (poignée arrière, mango trasero)

E - Starter grip and rope (poignée du lanceur et corde, mango del arrancador y cuerda)

F - Muffler (silencieux, silenciador)

G - Primer bulb (poire d’amorçage, bomba de cebado)

H - Start lever (levier de volet de départ, palanca de arranque)

I - Quick shutoff switch (commutateur de coupure rapide, interruptor de apagado rápido)

J - Throttle trigger (gâchette d’accélérateur, gatillo del acelerador)

K - Curved shaft grass deflector (déflecteur d’herbe d’arbre courbe, deflector de pasto del eje curvo)

L - Straight shaft grass deflector (déflecteur d’herbe d’arbre droit, deflector de pasto para eje recto)

M- Fuel cap (bouchon de carburant, tapa del tanque)

26SS

Fig. 1

26CS

Fig. 2

Fig. 3

A - Front handle (poignée avant, mango

delantero)

B - Washer (rondelle, arandela)

C - Bolt (boulon, perno)

D - Wing nut (écrou à oreilles, tuerca de

mariposa)

A - Wing nut (écrou à oreilles, tuerca de

mariposa)

B - Washer (rondelle, arandela)

C - Bolt (boulon, perno)

D - Grass deflector (déflecteur d’herbe, deflector

de pasto)

A - Drive shaft (arbre d’entraînement, eje de

impulsión)

B - Spool retainer (retenue de bobine, retén del

carrete)

C - Plastic seal (étanchéité en plastique, sello de

plástico)

D - String head assembly (ensemble de tête de

couple, conjunto del cabezal de hilo)

Fig. 5

26CS

A - Pull strings (tirer vers l’extérieur, tira del

hilo)

B - Slots (fentes, ranuras)

Fig. 4

Fig. 8

PROPER OPERATING

POSITION

BONNE POSITION

DE TRAVAIL

POSICIÓN

CORRECTA PARA

EL MANEJO DE LA

HERRAMIENTA

26CS

Fig. 9

Fig. 10

A - Dangerous cutting area (zone de coupe

dangereuse, área peligrosa de corte)

B - Direction of rotation (sens de rotation,

sentido de rotación)

C - Best cutting area (zone d’efficacité maximum,

mejor área de corte)

26SS

Fig. 11

A - Spool retainer (retenue de bobine, retén del

carrete)

Fig. 12

A - Insert into string head (insérer dans

l’extrémité de la chaîne, inserte en el

cabezal del hilo)

B - Push down and twist to align (pousser vers

le bas et tordre pour aligner, empuje hacia

abajo y gire para alinear)

A B

A - Start position (position de démarrage,

posición de arranque)

B - Start lever (levier de volet de départ, palanca

de arranque)

C - Run position (position de marche, posición

de marcha)

A - Gear head (carter d’engrenages, cabezal de

engranajes)

B - Slot (fente, ranura)

C - Square tab (languette carrée, orejeta

cuadrada)

D - Wing nut (écrou à oreilles, tuerca de

mariposa)

E - Mounting bracket (support de montage,

soporte de montaje)

F - Drive shaft (arbre moteur, eje de impulsión)

G - Screw (vis, tornillo)

H - Pin (axe, pasador)

I - Grass deflector (déflecteur d’herbe, deflector

de pasto)

Fig. 6

26SS

Fig. 7

A - Quick shutoff switch (commutateur de

coupure rapide, interruptor de apagado

rápido)

B - Primer bulb (poire d’amorçage, bomba de

cebado)

C - Throttle trigger (gâchette d’accélérateur,

gatillo del acelerador)

Fig. 13

A - Spool (orejeta ranurada, carrete)

B - Slots (fentes, ranuras)

Fig. 14

A - Hook (agrafe, gancho)

B - Slot (fente, ranura)

Fig. 15

A - Pull strings to secure (tirer vers l’extérieur,

tire)

B - Slots (fentes, ranuras)

Fig. 17

Fig. 18

A - Latch (loquet, pestillo)

B - Filter screen (filtre écran, filtro pantalla)

C - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

A - Idle speed screw (vis de ralenti, tornillo de

ajuste de la velocidad en vacío)

B - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

Fig. 16

A - Latch (loquet, pestillo)

B - Pull cover to open (tirer sur le couvercle

pour l’ouvrir, tire de la tapa para abrirla)

C - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

Page 2

 Introduction ...................................................................................................................................................................... 2

Introduction / Introducción

 General Safety Rules ........................................................................................................................................................ 3

Règles de sécurité générales / Reglas de seguridad generales

Specific Safety Rules ........................................................................................................................................................ 3

Règles de sécurité particulières / Reglas de seguridad específicas

Symbols ............................................................................................................................................................................ 4

Symboles / Símbolos

 Features ............................................................................................................................................................................ 5

Caractéristiques / Características

 Assembly .......................................................................................................................................................................5-6

Assemblage / Armado

 Operation .......................................................................................................................................................................6-8

Utilisation / Funcionamiento

 Maintenance ................................................................................................................................................................9-10

Entretien / Mantenimiento

 Troubleshooting .........................................................................................................................................................10-11

Dépannage / Corrección de problema

 Warranty ....................................................................................................................................................................12-14

Garantie / Garantía

 Parts Ordering and Service ...............................................................................................................................Back Page

Commande de pièces et réparation / Pedidos de piezas y servicio................................................. Page arrière / Pág. posterio

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto

se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

Page 3 — English

GENERAL SAFETY RULES

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below may result in electric shock,

fire and/or carbon monoxide poisoning which will cause

death or serious personal injury.

READ ALL INSTRUCTIONS

 For safe operation, read and understand all instructions

before using this product. Follow all safety instructions.

Failure to follow all safety instructions listed below, can

result in serious personal injury.

 Do not allow children or untrained individuals to use this

unit.

 Never start or run the engine in a closed or poorly venti-

lated area; breathing exhaust fumes can kill.

Clear the work area before each use. Remove all objects

such as rocks, broken glass, nails, wire, or string which

can be thrown or become entangled in the cutting line

or blade.

 Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

Wear heavy, long pants, long sleeves, boots, and gloves.

Do not wear loose fitting clothing, short pants, sandals,

or go barefoot. Do not wear jewelry of any kind.

Product users on United States Forest Service land, and

in some states, must comply with fire prevention regula-

tions. This product is equipped with a spark arrestor;

however, other user requirements may apply. Check with

your federal, state, or local authorities.

Never operate this unit on the operator’s left side.

Secure long hair above shoulder level to prevent entangle-

ment in moving parts.

Keep all bystanders, children, and pets at least 50 ft. away.

Bystanders should be encouraged to wear eye protection.

Do not operate this unit when you are tired, ill, or under

the influence of alcohol, drugs, or medication.

Do not operate in poor lighting.

Keep firm footing and balance. Do not overreach. Over-

reaching can result in loss of balance or exposure to hot

surfaces. Keep cutting attachment below waist.

 To avoid hot surfaces, never operate the unit with the

bottom of the engine above waist level.

Keep all parts of your body away from any moving part.

Do not touch area around the muffler or cylinder of the

unit; these parts get hot from operation.

 Always stop the engine and remove the spark plug wire

before making any adjustments or repairs except for

carburetor adjustments.

 Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace any damaged parts before use.

 The string head will rotate during carburetor

adjustments.

It has been reported that vibrations from hand-held tools

may contribute to a condition called Raynaud’s Syndrome

in certain individuals. Symptoms may include tingling,

numbness, and blanching of the fingers, usually apparent

upon exposure to cold. Hereditary factors, exposure to

cold and dampness, diet, smoking, and work practices

are all thought to contribute to the development of these

symptoms. It is presently unknown what, if any, vibrations

or extent of exposure may contribute to the condition.

There are measures that can be taken by the operator to

possibly reduce the effects of vibration:

a) Keep your body warm in cold weather. When operating

the unit wear gloves to keep your hands and wrists

warm. It is reported that cold weather is a major factor

contributing to Raynaud’s Syndrome.

b) After each period of operation, exercise to

increase blood circulation.

c) Take frequent work breaks. Limit the amount of

exposure per day.

d) Keep the product well maintained, fasteners

tightened and worn parts replaced.

If you experience any of the symptoms of this condition,

immediately discontinue use and see your physician about

these symptoms.

 Mix and store fuel in a container approved for gasoline.

Do not smoke while fueling or mixing fuel.

 Mix fuel outdoors where there are no sparks or flames.

Wipe up any fuel spillage. Move 30 ft. away from refueling

site before starting engine.

 Stop the engine and allow to cool before refueling or

storing the unit.

 Allow the engine to cool; empty the fuel tank into a con-

tainer approved for gasoline and secure the unit from

moving before transporting in a vehicle.

 Replace string head if cracked, chipped, or damaged

in any way. Be sure the string head or blade is properly

installed and securely fastened. Failure to do so can cause

serious injury.

 Make sure all guards, straps, deflectors, and handles are

properly and securely attached.

 Never use blades, flailing devices, wire, or rope. Use only

the manufacturer’s replacement string in the cutting head.

Do not use any other cutting attachment. To install any

other brand of cutting head to this string trimmer can

result in serious personal injury.

Never operate unit without the grass deflector in place

and in good condition.

 Maintain a firm grip on both handles while trimming. Keep

string head below waist level. Never cut with the string

head located over 30 in. or more above the ground.

SPECIFIC SAFETY RULES

Page 4 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME EXPLANATION

Safety Alert Symbol Indicates a potential personal injury hazard.

Read the Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye and Hearing Protection

Always wear eye protection with side shields marked to

comply with ANSI Z87.1 as well as hearing protection when

operating this equipment.

Keep Bystanders Away Keep all bystanders at least 50 ft. away.

Ricochet

Thrown objects can ricochet and result in personal injury or

property damage.

No Blade

Do not install or use any type of blade on a product display-

ing this symbol.

Gasoline and Lubricant

Use unleaded gasoline intended for motor vehicle use with

an octane rating of 87 [(R + M) / 2] or higher. This product is

and 2-cycle lubricant.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

CAUTION:

(Without Safety Alert Symbol) Indicates a situation that may result in property

damage.

Page 5 — English

FEATURES

PRODUCT SPECIFICATIONS

Weight (dry)

26CS .....................................................................................................................................................................8.2 lbs.

26SS .....................................................................................................................................................................8.9 lbs.

String cutting width ........................................................................................................................................................17 in.

Engine displacement .......................................................................................................................................................26cc

String diameter ........................................................................................................................................................... .080 in.

KNOW YOUR STRING TRIMMER

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

EZ WIND

™

TAP ADVANCE SYSTEM

The EZ Wind

™

Tap Advance System allows easy line advance

during trimmer operation.

GRASS DEFLECTOR

The trimmer includes a grass deflector that helps protect

you from flying debris.

TOP-MOUNTED MOTOR

The top-mounted motor improves balance and is located

away from the dust and debris of the cutting area.

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-242-4672 for assistance.

PACKING LIST

Trimmer Assembly

Front Handle

Curved Shaft Grass Deflector – 26CS

Straight Shaft Grass Deflector – 26SS

Bottle of 2-Cycle Lubricant

String Head Assembly

Operator’s Manual

WARNING:

If any parts are damaged or missing, do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

Page 6 — English

ASSEMBLY

WARNING:

To prevent accidental starting that could cause serious

personal injury, always disconnect the engine spark plug

wire from the spark plug when assembling parts.

FRONT HANDLE

See Figure 2.

NOTE: On units with curved shafts, for shipping purposes

only, the handle is located underneath the drive shaft housing.

The handle must be rotated before operating the trimmer.

 Slightly loosen the wing nut on the handle.

 Rotate the handle on the drive shaft housing at the loca-

tion indicated by the label on the shaft.

 Retighten the wing nut to secure the handle in place.

STRING HEAD ASSEMBLY

See Figures 3 - 4.

Place the string head assembly on the end of the drive

shaft housing. Make sure the hex-shaped opening on

the string head assembly seats completely on the drive

shaft. Install the spool retainer to secure.

Install the spool retainer:

Turn the spool retainer clockwise for 26CS.

Turn the spool retainer counterclockwise for 26SS.

 Remove the plastic seal from the string head assembly.

Slide strings into the housing eyelets and pull outward

to rotate the spool into the cutting position.

 Push the spool retainer down while pulling on string(s)

to manually advance the string and to check for proper

assembly of the string head.

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

CURVED SHAFT GRASS DEFLECTOR – 26CS

See Figure 5.

WARNING:

The line cutting blade on the grass deflector is sharp.

Avoid contact with the blade. Failure to avoid contact

can result in serious personal injury.

 Remove the bolt, washer, and wing nut from grass

deflector.

 Press the grass deflector onto the bottom of the curved

shaft as shown.

 Insert the bolt through the grass deflector and the bracket

on the curved shaft.

 Place the washer on the bolt.

 Place the wing nut on the bolt and tighten securely.

STRAIGHT SHAFT GRASS DEFLECTOR –

26SS

See Figure 6.

 Remove the wing nut and mounting bracket from the grass

deflector.

 Assemble straight shaft grass deflector to drive shaft so

that the pin in the grass deflector fits in the locator hole

in the lower side of the drive shaft near the gear head.

 Place the mounting bracket over the drive shaft so the

square tab on the mounting bracket fits into the slot in

the straight shaft grass deflector.

 Rotate the mounting bracket so the screw on the grass

deflector goes into the slot on the mounting bracket.

 Reinstall the wing nut and tighten securely.

OPERATION

WARNING:

Never use blades, flailing devices, wire, or rope on this prod-

uct. Do not use any attachments or accessories not rec-

ommended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

Before each use, inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps, etc.

Tighten securely all fasteners and caps and do not operate

this product until all missing or damaged parts are replaced.

Please call 1-800-242-4672 or contact an authorized service

center for assistance.

Page 7 — English

OPERATION

FUELING AND REFUELING THE TRIMMER

FUEL MIXTURE

This product is powered by a 2-cycle engine and requires

premixing gasoline and 2-cycle oil. The mixture should be

at a 50:1 ratio.

NOTE: We recommend you use ONLY Homelite (exact mix)

or G oil in your product.

TO MIX THE FUEL:

 Use a clean container that is approved for use with

gasoline.

 Mix the 2-cycle engine oil with unleaded gasoline in the

container, according to the instructions on the oil

package.

This engine is certified to operate on unleaded gasoline

intended for automotive use with an octane rating of 87

[(R + M) / 2] or higher. Do not use automotive oil or 2-cycle

outboard oil.

NOTE: Most fuel mixture will stay fresh up to 30 days. DO

NOT mix quantities larger than usable in a 30 day period.

PREMIUM EXACT MIX (50:1)

GASOLINE LUBRICANT

1 gallon (US) 2.6 oz.

1 liter 20 cc (20 ml)

OXYGENATED FUELS

DO NOT USE E85 FUEL. IT WILL VOID YOUR

WARRANTY.

NOTE: Fuel system damage or performance problems re-

sulting from the use of an oxygenated fuel containing more

than the percentages of oxygenates stated previously are

not covered under warranty.

Ethanol. Gasoline containing up to 10% ethanol by vol-

ume (commonly referred to as E10) or 15% ethanol by

volume (commonly referred to as E15) are acceptable.

Do not use E85 fuel.

FILLING TANK

 Clean surface around fuel cap to prevent contamination.

 Set trimmer on its side so that the spout points up.

 Loosen fuel cap slowly. Rest the cap on a clean surface.

 Carefully pour fuel into the tank. Avoid spillage.

 Immediately replace fuel cap and hand tighten. Wipe up

any fuel spillage.

NOTE: It is normal for smoke to be emitted from a new

engine after first use.

WARNING:

Always shut off engine before fueling. Never add fuel to a

machine with a running or hot engine. Move at least 30 ft.

from refueling site before starting engine. Do not smoke

and stay away from open flames and sparks. Failure to

safely handle fuel could result in serious personal injury.

STARTING AND STOPPING

See Figures 7 - 8.

Trimmer should be on a flat, bare surface for starting. The

starting method differs depending on whether the engine is

cold or warm.

To start a cold engine:

DO NOT squeeze the throttle trigger until the engine starts

and runs.

Lay the trimmer on a flat, bare surface.

PRIME - Press the primer bulb 7 times.

SET the start lever to the START position.

PULL the rope until the engine starts.

Squeeze the trigger to run.

NOTE: Squeezing and releasing the throttle trigger releases

the start lever to the RUN position.

To restart a warm engine:

SQUEEZE the throttle trigger.

PULL the rope until the engine starts.

NOTE: If the engine starts and stops before the throttle trigger

engages, squeeze the throttle trigger and pull the rope until

the engine starts and runs. Squeezing and releasing the

throttle trigger releases the start lever to the RUN position.

To stop the engine:

Press and hold the quick shutoff switch in the stop “ ”

position until the engine stops.

IF ASSISTANCE IS REQUIRED STARTING

THIS PRODUCT:

Do not return this product to the retail store where it was

purchased. Please call our Customer Service Department

for any issues you may have.

For Help Call: 1-800-242-4672

OPERATING THE TRIMMER

See Figure 9.

WARNING:

Always position the unit on the operator’s right side. The

use of the unit on the operator’s left side will expose the

operator to hot surfaces and can result in possible burn

injury.

Page 8 — English

OPERATION

WARNING:

To avoid burns from hot surfaces, never operate unit with

the bottom of the engine above waist level.

Hold the trimmer with your right hand on the rear handle

and your left hand on the front handle. Keep a firm grip with

both hands while in operation. Trimmer should be held at a

comfortable position with the rear handle about hip height.

Always operate trimmer at full throttle. Cut tall grass from the

top down. This will prevent grass from wrapping around the

shaft housing and string head which may cause damage from

overheating. If grass becomes wrapped around the string

head, STOP THE ENGINE, disconnect the spark plug wire,

and remove the grass. Prolonged cutting at partial throttle

will result in lubricant dripping from the muffler.

WARNING:

Always hold the string trimmer away from your body, keep-

ing clearance between your body and the product. Any

contact with the housing or string trimmer cutting head can

result in burns and/or other serious personal injury.

CUTTING TIPS

See Figures 10 - 11.

 Avoid hot surfaces by always keeping the tool away from

your body. (Proper operating position shown in figure 9.)

Keep the trimmer tilted toward the area being cut; this is

the best cutting area.

The curved shaft trimmer cuts when passing the unit from

right to left. The straight shaft trimmer cuts when passing

the unit from left to right. This will avoid throwing debris at

the operator. Avoid cutting in the dangerous area shown

in figure 10.

 Use the tip of string to do the cutting; do not force string

head into uncut grass.

 Wire and picket fences cause extra string wear, even

breakage. Stone and brick walls, curbs, and wood may

wear string rapidly.

 Avoid trees and shrubs. Tree bark, wood moldings, siding,

and fence posts can easily be damaged by the string.

ADVANCING STRING USING THE EZ WIND

™

TAP ADVANCE SYSTEM

String advance is controlled by tapping string head on grass

while running engine at full throttle.

 Run engine at full throttle.

 Tap string head on ground to advance string. String

advances each time the head is tapped.

 Several taps may be required until string strikes the cut

off blade.

 Resume trimming.

NOTE: If the string is worn too short you may not be able to

advance the string by tapping it on the ground. If so, STOP

THE ENGINE, disconnect the spark plug wire, and manually

advance the string.

ADVANCING THE STRING MANUALLY

With the engine off and the spark plug wire disconnected,

push the spool retainer down while pulling on string(s) to

manually advance the string.

CUT-OFF BLADE

This trimmer is equipped with a cut-off blade on the grass

deflector. For best cutting, advance string by tapping the

string head until the string is trimmed to length by the cut-off

blade. Advance string whenever you hear the engine running

faster than normal, or when trimming efficiency diminishes.

This will maintain best performance and keep string long

enough to advance properly.

Page 9 — English

WARNING:

When servicing, use only identical Homelite replacement

parts. Use of any other parts may create a hazard or

cause product damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries. If operation

is dusty, also wear a dust mask.

WARNING:

Before inspecting, cleaning, or servicing the machine,

shut off engine, wait for all moving parts to stop, and

disconnect spark plug wire and move it away from spark

plug. Failure to follow these instructions can result in

serious personal injury or property damage.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use

clean cloths to remove dirt, dust, lubricant, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating lubricants, etc., come in con-

tact with plastic parts. Chemicals can damage, weaken or

destroy plastic which may result in serious personal

injury.

You can often make adjustments and repairs described here.

For other repairs, have the trimmer serviced by an authorized

service dealer.

SPOOL REPLACEMENT

EZ WIND

™

TAP ADVANCE SYSTEM

NEW PREWOUND SPOOL

See Figures 12 - 13.

If replacing string only, refer to String Replacement later

in this manual.

Use only .080 in. diameter trimmer line.

 Stop the engine and disconnect the spark plug wire. Hold

the string head and unscrew the spool retainer.

To remove the spool retainer:

Turn the spool retainer counterclockwise for 26CS.

Turn the spool retainer clockwise for 26SS.

 Remove the empty spool from the string head. Keep the

spring attached to the spool.

MAINTENANCE

 Make sure the two strings are captured in the slots op-

posite each other on the new spool. Make sure the end

of each string is extended approximately 6 in. beyond

each slot.

 Align the slot(s) on the spool to the eyelet(s) on the string

head housing. Push down and turn the spool in the nec-

essary direction to align the slot(s).

 Make sure the string head and the spool retainer are

installed on the drive shaft.

To install the spool retainer:

Turn the spool retainer clockwise for 26CS.

Turn the spool retainer counterclockwise for 26SS.

 Slide strings into the housing eyelets and pull outward to

rotate the spool into the cutting position.

 Push the spool retainer down while pulling on string(s)

to manually advance the string and to check for proper

assembly of the string head.

STRING REPLACEMENT

See Figures 14 - 15.

 Stop the engine and disconnect the spark plug wire. Hold

the string head and unscrew the spool retainer.

To remove the spool retainer:

Turn the spool retainer counterclockwise for 26CS.

Turn the spool retainer clockwise for 26SS.

 Remove the spool from the string head.

NOTE: Keep the spring attached to the spool. Remove

any old string remaining on the spool.

 Cut one piece of trimmer line 18 ft. long. Find the middle

of the string section. Loop the string around the hook in

the center of the spool. Carefully wind the string in the

direction indicated on the top of the spool. Nearing the

end of the string, slide one end of the string into each

slot of the spool. Do not overfill.

 Replace the spool and the spool retainer. Refer to Spool

Replacement earlier in this manual.

CLEANING THE EXHAUST PORT

Depending on the type of fuel used, the type and amount

of lubricant used, and/or your operating conditions, the

exhaust port may become blocked with carbon deposits.

If you notice a power loss with your gas powered tool, you

may need to remove these deposits to restore performance.

We highly recommend that only qualified service technicians

perform this service.

SPARK ARRESTOR

The spark arrestor must be replaced every 50 hours or yearly

to ensure proper performance of the product. Spark arres-

tors may be in different locations depending on the model

purchased. Please contact the nearest service dealer for the

location of the spark arrestor for your model.

Page 10 — English

MAINTENANCE

CLEANING THE AIR FILTER SCREEN

See Figures 16 - 17.

For proper performance and long life, keep air filter screen

clean.

 Remove the air filter cover by pushing down on the latch

with your thumb while gently pulling on the cover.

 Brush the air filter screen lightly to clean.

 Replace the air filter cover by inserting the tabs on the

bottom of the cover into the slots on the air filter base;

push the cover up until it latches securely in place.

FUEL CAP

WARNING:

Check for fuel leaks. A leaking fuel cap is a fire hazard

and must be replaced immediately. If you find any leaks,

correct the problem before using the product. Failure

to do so could result in a fire that could cause serious

personal injury.

The fuel cap contains a non-serviceable filter and a check

valve. A clogged fuel filter will cause poor engine perfor-

mance. If performance improves when the fuel cap is loos-

ened, check valve may be faulty or filter clogged. Replace

fuel cap if required.

SPARK PLUG

This engine uses a Champion RCJ6Y or equivalent spark

plug with .025 in. electrode gap. Use an exact replacement

and replace annually, or more frequently if necessary.

STORING THE TRIMMER

 Clean all foreign material from the trimmer. Store it in a

well-ventilated place that is inaccessible to children. Keep

away from corrosive agents such as garden chemicals

and de-icing salts.

 Abide by all Federal and local regulations for the safe

storage and handling of gasoline.

WHEN STORING 1 MONTH OR LONGER:

 Drain all fuel from tank into a container approved for

gasoline. Run engine until it stops.

TROUBLESHOOTING

Problem Possible Cause Solution

Engine will not start. No spark.

No fuel.

Engine is flooded.

Starter rope pulls harder now than

when new.

Check spark. Remove spark plug. Re-

attach the spark plug cap and lay spark

plug on metal cylinder. Pull the starter

rope and watch for spark at spark plug

tip. If there is no spark, repeat test with

a new spark plug.

Push primer bulb until bulb is full of

fuel. If bulb does not fill, primary fuel

delivery system is blocked. Contact

a servicing dealer. If primer bulb fills,

engine may be flooded, proceed to

next item.

Remove spark plug, turn trimmer so

spark plug hole is aimed at the ground.

Rotate the choke dial to “RUN” posi-

tion and pull starter cord 10 to 15

times. This will clear excess fuel from

engine. Clean and reinstall spark plug.

Pull starter three times with choke dial

at “RUN”. If engine does not start, ro-

tate choke dial to “FULL CHOKE” posi-

tion and repeat normal starting proce-

dure. If engine still fails to start, repeat

procedure with a new spark plug.

Contact a servicing dealer.

Page 11 — English

TROUBLESHOOTING

Problem Possible Cause Solution

Engine starts but will not accelerate. Engine requires approximately three

minutes to warm up.

Allow engine to completely warm up. If

engine does not accelerate after three

minutes, contact a servicing dealer.

Engine starts but will only run at high

speed at half choke.

Carburetor requires adjustment. Contact a servicing dealer.

Engine does not reach full speed and

emits excessive smoke.

Check lubricant fuel mixture.

Air filter is dirty.

Carburetor out of adjustment.

Use fresh fuel and the correct 2-cycle

lubricant mix.

Clean air filter. Refer to Cleaning

the Air Filter Screen earlier in this

manual.

Contact a servicing dealer.

Engine starts, runs, and accelerates

but will not idle.

Idle speed screw on carburetor needs

adjustment.

Turn idle speed screw clockwise to

increase idle speed. See figure 18.

String will not advance. String is welded to itself.

Not enough string on spool.

String is worn too short.

String is tangled on spool.

Engine speed is too slow.

Lubricate with silicone spray.

Install more string. Refer to String

Replacement earlier in this manual.

Pull strings while alternately pressing

down on and releasing spool retainer.

Remove string from spool and rewind.

Refer to String Replacement earlier in

this manual.

Advance string at full throttle.

Spool retainer hard to turn. Screw threads are dirty or damaged. Clean threads and lubricate with

grease – if no improvement, replace

the spool retainer.

Grass wraps around driveshaft housing

and string head.

Cutting tall grass at ground level.

Operating trimmer at part throttle.

Cut tall grass from the top down to

prevent wrapping.

Operate trimmer at full throttle.

Lubricant drips from muffler. Operating trimmer at part throttle.

Check lubricant/fuel mixture.

Air filter screen dirty.

Operate trimmer at full throttle.

Use fresh fuel and the correct 2-cycle

lubricant mix.

Clean air filter. Refer to Cleaning

the Air Filter Screen earlier in this

manual.

Page 12 — English

WARRANTY

LIMITED WARRANTY STATEMENT

Homelite Consumer Products, Inc., (“Homelite”) warrants

to the original retail purchaser that this HOMELITE brand

outdoor product is free from defect in material and

workmanship and agrees to repair or replace, at Homelite’s,

discretion, any defective product free of charge within these

time periods from the date of purchase.

 Two years for all models if used for personal, family, or

household use;

 90 days for any unit used for other purposes, such as

rental or commercial.

This warranty extends to the original retail purchaser

only and commences on the date of the original retail

purchase.

Any part of the this product manufactured or supplied

by Homelite and found in the reasonable judgment of

Homelite to be defective in material or workmanship will

be repaired or replaced without charge for parts and labor

by a Homelite authorized service center.

The product, including any defective part, must be returned

to an authorized service dealer within the warranty period.

The expense of delivering the product to the dealer for

warranty work and the expense of returning it back to the

owner after repair or replacement will be paid by the owner.

Homelite’s responsibility in respect to claims is limited to

making the required repairs or replacements and no claim

of breach of warranty shall be cause for cancellation or

rescission of the contract of sale of any HOMELITE brand

product. Proof of purchase will be required by the dealer

to substantiate any warranty claim. All warranty work must

be performed by a Homelite authorized service center.

This warranty is limited to ninety (90) days from the date of

original retail purchase for any HOMELITE brand product

that is used for rental or commercial purposes, or any other

income-producing purpose.

This warranty does not cover any HOMELITE brand product

that has been subject to misuse, neglect, negligence, or

accident, or that has been operated in any way contrary

to the operating instructions as specified in this operator’s

manual. This warranty does not apply to any damage to

the product that is the result of improper maintenance or

to any product that has been altered or modified. The

warranty does not extend to repairs made necessary

by normal wear or by the use of parts or accessories

which are either incompatible with the HOMELITE

brand product or adversely affect its operation,

performance, or durability. In addition, this warranty does

not cover:

A. Tune-ups – Spark Plugs, Carburetor, Carburetor

Adjustments, Ignition, Filters

B. Wear items – Bump Knobs, Outer Spools, Cutting

Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive

Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades,

Blower Fans, Blower and Vacuum Tubes, Vacuum Bags

and Straps, Guide Bars, Saw Chains

Homelite reserves the right to change or improve

the design of any HOMELITE brand product without

assuming any obligation to modify any product previously

manufactured.

ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION

TO THE STATED WARRANTY PERIOD. ACCORDINGLY,

ANY SUCH IMPLIED WARRANTIES INCLUDING

MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN

THEIR ENTIRETY AFTER THE EXPIRATION OF THE

APPROPRIATE TWO-YEAR, ONE-YEAR, OR NINETY-DAY

WARRANTY PERIOD. HOMELITE’S OBLIGATION UNDER

THIS WARRANTY IS STRICTLY AND EXCLUSIVELY

LIMITED TO THE REPAIR OR REPLACEMENT OF

DEFECTIVE PARTS AND HOMELITE DOES NOT ASSUME

OR AUTHORIZE ANYONE TO ASSUME FOR THEM ANY

OTHER OBLIGATION. SOME STATES DO NOT ALLOW

LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY

LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY

TO YOU. HOMELITE ASSUMES NO RESPONSIBILITY

FOR INCIDENTAL, CONSEQUENTIAL, OR OTHER

DAMAGES INCLUDING, BUT NOT LIMITED TO, EXPENSE

OF RETURNING THE PRODUCT TO AN AUTHORIZED

HOMELITE SERVICE CENTER AND EXPENSE OF

DELIVERING IT BACK TO THE OWNER, MECHANIC’S

TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES,

RENTAL OF A LIKE PRODUCT DURING THE TIME

WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,

LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS

OF REVENUE, LOSS OF USE OF THE PRODUCT,

LOSS OF TIME, OR INCONVENIENCE. SOME STATES

DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE

ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY

TO YOU.

This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

This warranty applies to all HOMELITE brand products

manufactured by or for Homelite and sold in the United

States and Canada.

To locate your nearest Homelite authorized service

center, dial 1-800-242-4672 or log on to our website at

www.homelite.com.

Page 13 — English

WARRANTY

THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES TO MODEL NUMBERS

REQUIRED TO MEET THE CARB REQUIREMENTS.

The U.S. Environmental Protection Agency (EPA), the California Air Resources Board

(CARB), and Homelite Consumer Products, Inc., are pleased to explain the Emissions

Control System Warranty on your 2009 model year non-road or small off-road engine.

In California, new equipment that uses small off-road engines must be designed, built,

and equipped to meet the state’s stringent anti-smog standards. In other states, new

2000 and later model year non-road engines must be designed, built, and equipped

at the time of sale to meet the U.S. EPA regulations for small non-road engines. The

non-road engine must be free from defects in materials and workmanship which

cause it to fail to conform with U.S. EPA standards for the first two years of engine

use from the date of sale to the ultimate purchaser. Homelite Consumer Products,

Inc., must warrant the emission control system on your non-road or small off-road

engine for the period of time listed above provided there has been no abuse, neglect,

or improper maintenance of your non-road or small off-road engine.

Your emission control system may include parts such as the carburetor or fuel injection

system, the ignition system, catalytic converters, fuel tanks, valves, filters, clamps,

connectors, and other associated components. Also included may be hoses, belts

and connectors, and other emission-related assemblies.

Where a warrantable condition exists, Homelite Consumer Products, Inc., will repair

your non-road or small off-road engine at no cost to you, including diagnosis, parts,

and labor performed at an authorized service center for HOMELITE

brand outdoor

products.

MANUFACTURER’S WARRANTY COVERAGE:

This product’s emissions control system is warranted for two years. If any emission-

related part on your engine is defective, the part will be repaired or replaced by

Homelite Consumer Products, Inc., free of charge.

OWNER’S WARRANTY RESPONSIBILITIES

(a) As the non-road or small off-road engine owner, you are responsible for the perfor-

mance of the required maintenance listed in your operator’s manual. Homelite Consumer

Products, Inc., recommends that you retain all receipts covering maintenance on your

non-road or small off-road engine, but Homelite Consumer Products, Inc., cannot deny

warranty solely for the lack of receipts or for your failure to ensure the performance

of all scheduled maintenance. Any replacement part or service that is equivalent in

performance and durability may be used in non-warranty maintenance or repairs,

and shall not reduce the warranty obligations of Homelite Consumer Products, Inc.

(b) As the non-road or small off-road engine owner, you should be aware, however,

that Homelite Consumer Products, Inc., may deny you warranty coverage if your

non-road or small off-road engine or a part has failed due to abuse, neglect, improper

maintenance, or unapproved modifications.

authorized service dealer as soon as a problem exists. The warranty repairs should

be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you

should contact a Homelite Consumer Products, Inc., Customer Representative at

1-800-242-4672.

DEFECT WARRANTY COVERAGE REQUIREMENTS:

(a) The warranty period begins on the date the engine or equipment is delivered to

an ultimate purchaser.

(b) General Emissions Warranty Coverage. Homelite Consumer Products, Inc., war-

rants to the ultimate purchaser and each subsequent purchaser that your non-road or

small off-road engine is designed, built, and equipped at the time of sale to conform

with all applicable regulations adopted by the California Air Resources Board or the

United States Environmental Protection Agency; and that it is free from defects in

materials and workmanship which cause the engine to fail to conform with applicable

regulations for a period of two years from the date the non-road or small off-road

engine is purchased by the initial purchaser.

warranted part that is not scheduled for replacement as required in the Emissions

Maintenance Schedule and Warranty Parts List set forth below is warranted for two

years. If any such part (including any part that is scheduled only for regular inspec-

tion) fails during the period of warranty coverage, it will be repaired or replaced at

any HOMELITE

Authorized Service Center at no charge. Any such part repaired

or replaced under warranty will be warranted for the remaining warranty period. A

statement to the effect of “repair or replace as necessary” would not reduce the

period of warranty coverage. Any warranted part that is scheduled for replacement

as required maintenance in the Emissions Maintenance Schedule and Warranty Parts

List is warranted for the period of time prior to the first scheduled replacement point

for that part. Any such part repaired or replaced under warranty is warranted for the

remainder of the period prior to the first scheduled replacement point, and will be

repaired or replaced at any HOMELITE

Authorized Service Center for no charge

until that replacement point is reached.

Homelite Consumer Products, Inc., shall remedy warranty defects at any authorized

HOMELITE

Authorized Service Center, including any distribution center that may be

franchised to service the subject engines. Any diagnostic work done at a HOMELITE

Authorized Service Center shall be free of charge to the owner if such work determines

that a warranted part is defective. Any manufacturer-approved or equivalent replace-

ment part may be used for any warranty maintenance or repairs on emission-related

parts, and must be provided free of charge to the owner if the part is still under

warranty. Homelite Consumer Products, Inc., is liable for damages to other engine

components caused by the failure of a warranted part still under warranty.

Add-on or modified parts that are not exempted by the California Air Resource Board

may not be used. The use of any non-exempted add-on or modified parts will be

grounds for disallowing a warranty claim. Homelite Consumer Products, Inc., will not

be liable to warrant failures of warranted parts caused by the use of a non-exempted

add-on or modified part.

The California Air Resources Board’s Emission Warranty Parts List specifically

defines the emission-related warranted parts. (EPA’s regulations do not include a

parts list, but the EPA considers emission-related warranted parts to include all the

parts listed below.) Homelite Consumer Products, Inc., will provide any documents

that describe its warranty procedures or policies within five days upon request by

the California Air Resources Board.

EMISSIONS PARTS LIST

Emissions parts vary from product to product. Your emissions control system warranty

applies to any of the following components that may be included on your product:

(1) Fuel Metering System

(i) Carburetor and internal parts (and/or pressure regulator or fuel injection

system).

(ii) Air/fuel ratio feedback and control system.

(iii) Cold start enrichment system.

(iv) Fuel Tank.

(2) Air Induction System

(i) Controlled hot air intake system.

(ii) Intake manifold.

(iii) Air filter.

(3) Ignition System

(i) Spark Plugs.

(ii) Magneto or electronic ignition system.

(iii) Spark advance/retard system.

(4) Exhaust Gas Recirculation (EGR) System

(i) EGR valve body and carburetor spacer, if applicable.

(ii) EGR rate feedback and control system.

(5) Air Injection System

(i) Air pump or pulse valve.

(ii) Valves affecting distribution of flow.

(iii) Distribution manifold.

(6) Catalyst or Thermal Reactor System

(i) Catalytic converter.

(ii) Thermal reactor.

(iii) Exhaust manifold.

(7) Particulate Controls

(i) Traps, filters, precipitators, and any other device used to capture particulate

emissions.

(8) Miscellaneous Items Used in Above Systems

(i) Electronic controls.

(ii) Vacuum, temperature, and time sensitive valves and switches.

(iii) Hoses, belts, connectors, and assemblies.

Homelite Consumer Products, Inc., will furnish with each new engine written instruc-

tions for its maintenance and use by the owner.

The Emissions Compliance Period referred to on the Emissions Compliance label

indicates the number of operating hours for which the engine has been shown to

meet Federal emission requirements. Category C=50 hours, B=125 hours, and

A=300 hours.

HOMELITE CONSUMER PRODUCTS, INC., LIMITED WARRANTY STATEMENT FOR FEDERAL AND CALIFORNIA

EMISSION CONTROL SYSTEMS NON-ROAD AND SMALL OFF-ROAD ENGINES

YOUR WARRANTY RIGHTS AND OBLIGATIONS

Page 14 — English

WARRANTY

EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LIST

Emissions Parts Inspect Before Clean Every Replace Clean Every Replace Every

Each Use 5 Hours Every 25 Hours 25 Hours 50 Hours

or Yearly or Yearly

CATALYTIC MUFFLER ASSEMBLY ................................................................................................................... X

AIR FILTER ASSY

includes:

Screen .............................................................. X

FUEL TANK ASSY

includes:

Fuel Lines ........................ X

Fuel Cap .......................... X

IGNITION ASSY

includes:

Spark Plug ........................................................................................ X

ALL EMISSIONS-RELATED PARTS ARE WARRANTED FOR TWO YEARS OR FOR THE PERIOD OF TIME PRIOR TO

THE PARTS FIRST SCHEDULED REPLACEMENT WHICHEVER COMES FIRST.

THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER

Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s

original emission level, please refer to the maintenance section below.

MAKE THE MOST OF YOUR PURCHASE!

Go to www.homelite.com and register your new tool on-line.

Your product has been fully tested prior to shipment

to ensure your complete satisfaction.

For any questions about operating or maintaining

your product, call the Homelite Help Line!

CALL

1-800-242-4672

www.homelite.com

To register your Homelite product by regular mail, please print the following information on a 3 in. x 5 in. card or

standard postcard: your name, mailing address, phone numbers, email address, Homelite product(s) purchased

with item number from package, and serial number for each product. Mail the card to: Homelite Consumer Prod-

ucts, Attn. Homelite Registration, 1428 Pearman Dairy Road, Anderson, SC 29625.To receive information on our

company and products, please include the following statement on your registration card: “Send me information

on your products and company using the contact information I am providing with this product registration.”

Page 3 — Français

RÈGLES DE SÉCURITÉ GÉNÉRALES

AVERTISSEMENT :

Lire et veiller à bien comprendre toutes les instructions. Le

non-respect de toutes les instructions ci-dessous peut entraîner

un choc électrique, un incendie et/ou intoxication au monoxyde

de carbone qui causant des blessures graves ou mortelles.

LIRE TOUTES LES INSTRUCTIONS

 Pour travailler en toute sécurité, lire et veiller à bien comprendre

toutes les instructions avant d’utiliser ce produit. Respecter

toutes les instructions de sécurité. Le non respect des instructions

de sécurité ci-dessous peut entraîner des blessures graves.

 Ne pas laisser des enfants ou personnes n’ayant pas reçu une

formation adéquate utiliser cet outil.

 Ne jamais lancer ou faire tourner le moteur dans un

endroit clos ou mal aéré. Les gaz d’échappement peuvent être

mortels.

 Déblayer la zone de travail avant chaque utilisation. La

débarrasser de tous les objets tels que cailloux, verre brisé,

clous, fils métalliques, cordes, etc. risquant d’être projetés ou

de se prendre dans la ligne de coupe ou la lame.

 Toujours porter une protection oculaire certifiée conforme à

la norme ANSI Z87.1 ainsi qu'un protection auditive. Si cette

précaution n’est pas prise, des objets peuvent être projetés

dans les yeux et causer des lésions graves.

 Porter des pantalons longs, manches longues, des chaussures

de travail et des gants épais. Ne pas porter de vêtements

amples, bijoux, shorts, sandales et ne pas travailler pieds nus.

Ne porter aucun bijou.

 Les produits utilisés sur les territoires des services forestiers

des États-Unis et de certains états doivent être conformes aux

réglementations de lutte contre l’incendie. Cet outil est doté

d’un pare-étincelles, toutefois, d’autres dispositifs peuvent être

requis. Consulter les autorités locales et gouvernementales.

 Ne jamais utiliser cet outil en le tenant du côté gauche.

 Attacher les cheveux longs pour les maintenir au-dessus des

épaules, afin qu’ils ne se prennent pas dans les pièces en

mouvement.

 Garder les badauds, enfants et animaux à une distance de 15 m

(50 pi) minimum. Recommander aux personnes présente de

porter une protection oculaire.

 Ne pas utiliser ce taille-bordures en état de fatigue, si l’on est souffrant

ou sous l’influence de l’alcool, de drogues ou de médicaments.

 Ne pas travailler sous un éclairage insuffisant.

 Se tenir bien campé et en équilibre. Ne pas travailler

hors de portée. Le travail hors de portée risque de faire

perdre l’équilibre ou de causer un contact avec les pièces

brûlantes. Gardez le dispositif de coupe sous la taille.

 Garder toutes les parties du corps à l’écart des pièces

en mouvement.

 Pour éviter le contact avec les parties brûlantes, ne jamais

travailler avec le bas du moteur au-dessus du niveau de

la taille.

Ne pas toucher les alentours de l’échappement ou du cylindre,

qui deviennent brûlants pendant l’utilisation.

 Toujours arrêter le moteur et débrancher le fil de la bougie avant

d’effectuer tout entretien ou réglage, à l’exception des réglages

du carburateur.

 Inspecter l’outil avant chaque utilisation pour s’assurer qu’il

n’y a pas de pièces desserrées, de fuites ce carburant, etc.

Remplacer les pièces endommagées avant utilisation.

 La tête de coupe tourne pendant le réglage du carburateur.

 Il a été rapporté que, chez certaines personnes, les vibrations

produites par les outils à main motorisés peuvent contribuer

au développement d’une affection appelée syndrome de

Raynaud. Les symptômes peuvent inclure des picotements,

l’insensibilisation et le blanchissement des doigts et sont

habituellement provoqués par l’exposition au froid. L’hérédité,

l’exposition au froid et à l’humidité, le régime alimentaire,

la fumée et les habitudes de travail sont tous des facteurs

considérés comme contribuant au développement de ces

symptômes. Il n’existe actuellement aucune preuve qu’un

certain type de vibration ou le degré d’exposition contribue

réellement au développement de cette affectation. Certaines

mesures, susceptibles de réduire les effets des vibrations,

peuvent être prises par l’opérateur :

a) Garder le corps au chaud par temps froid. Pendant

l’utilisation, porter des gants afin de tenir les mains

et les poignets au chaud. Il a été établi que le froid

est l’une des principales causes du symptôme de

Raynaud.

b) Après chaque période d’utilisation, faire des exercices

pour accroître la circulation.

c) Faire des pauses fréquentes. Limiter la durée

d’exposition quotidienne.

d) Garder le produit bien entretenu, toutes les pièces de

boulonnerie serrées et remplacer les pièces usées.

En cas d’apparition de l’un ou plusieurs des symptômes

décrits ci-dessus, cesser d’utiliser l’outil et consulter

un médecin.

 Mélanger et conserver le carburant dans un bidon ou jerrycan

approuvé pour l’essence. Ne pas fumer pendant le ravitaillement

en carburant ou de mélange de carburant.

 Mélanger le carburant à l’extérieur, loin de toute flamme ou

source d’étincelles. Essuyer tout carburant répandu. S’éloigner

de 9 m (30 pi) du point d’approvisionnement avant de lancer le

moteur.

 Arrêter le moteur et le laisser refroidir avant de faire le plein ou

de le remiser.

 Pour le transport dans un véhicule, le réservoir doit être vidé

dans un bidon ou jerrycan approuvé pour l’essence et l’outil

bien arrimé.

 Si la tête de coupe est fendue, brisée ou endommagée de

quelque façon que ce soit, la remplacer. S’assurer que la tête

de coupe ou la lame est correctement installée et solidement

assujettie. S’il ne le sont pas, l’opérateur court des risques de

blessures graves.

 S’assurer que tous les dispositifs de protection, déflecteurs et

poignées sont correctement installés et solidement assujettis.

 Ne jamais utiliser de lames ou de dispositifs à fléau, fil et cordes.

Utiliser exclusivement des lignes de coupe d’origine. Ne pas

utiliser d’autres accessoires de coupe. L’utilisation d’une tête

de coupe d’autre marque sur ce taille-bordures peut entraîner

des blessures graves.

 Ne jamais utiliser l’outil si le déflecteur d’herbe n’est pas en

place et en bon état.

 Tenir fermement les deux poignées pendant le travail. Tenir la

tête de coupe au-dessous du niveau de la taille. Ne jamais tailler

avec la tête de coupe à plus de 762 mm (30 po) du sol.

RÈGLES DE SÉCURITÉ PARTICULIÈRES

Page 4 — Français

Les termes de mise en garde suivants et leur signification ont pour but d’expliquer le degré de risques associé à l’utilisation

de ce produit.

SYMBOLE SIGNAL SIGNIFICATION

DANGER :

Indique une situation extrêmement dangereuse qui, si elle n’est pas évitée,

aura pour conséquences des blessures graves ou mortelles.

AVERTISSEMENT :

Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée,

pourrait entraîner des blessures graves ou mortelles.

ATTENTION :

Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée,

pourraît entraîner des blessures légères ou de gravité modérée.

ATTENTION :

(Sans symbole d’alerte de sécurité) Indique une situation pouvant entraîner

des dommages matériels.

SYMBOLES

Certains des symboles ci-dessous peuvent être utilisés sur l’outil. Veiller à les étudier et apprendre leur signification

pour assurer la sécurité d’utilisation.

SYMBOLE NOM EXPLICATION

Symbole d’alerte de sécurité Indique un danger potentiel de blessure.

Lire le manuel d’utilisation

Pour réduire les risques de blessures, l’utilisateur doit lire

et veiller à bien comprendre le manuel d’utilisation avant

d’utiliser ce produit.

Protection oculaire et auditive

Toujours porter une protection oculaire certifiée conforme à

la norme ANSI Z87.1 ainsi qu'un protection auditive.

Ne laisser personne s’approcher

Garder les badauds à une distance de 15 m (50 pi)

minimum.

Ricochet

Les objets projetés peuvent ricocher et infliger des blessures

ou causer des dommages matériels.

Ne pas utiliser de lame

Ne jamais utiliser une lame quelconque sur un outil portant

ce symbole.

Essence et lubrifant

Utiliser de l’essence sans plomb pour automobiles, avec un

indice d’octane de 87 [(R + M) / 2] ou plus. Cet outil utilise

un moteur deux temps qui nécessite le mélange d’essence

et d’lubrifant 2 temps.

La page charge ...

Homelite UT21006 Manuel utilisateur

Marque: Homelite

Modèle: UT21006

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

Trimmer UT21006

Télécharger le PDF

rapport

dans d''autres langues

English: Homelite UT21006 User manual
español: Homelite UT21006 Manual de usuario

Homelite UT21006 Manuel utilisateur

Ce manuel convient également à

Homelite UT21006 Manuel utilisateur

dans d''autres langues

Documents connexes