Yamaha RX-550 Le manuel du propriétaire

RX-V550

AV Receiver

OWNER'S MANUAL

U

00_RXV550_U_EN.book Page 1 Tuesday, February 17, 2004 9:21 AM

IMPORTANT SAFETY INSTRUCTIONS

i

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert you to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle

is intended to alert you to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

1 Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and use instructions

should be followed.

5 Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners. Use

a damp cloth for cleaning.

6 Attachments – Do not use attachments not recommended by

the product manufacturer as they may cause hazards.

7 Water and Moisture – Do not use this product near water –

for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a swimming pool;

and the like.

8 Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall,

causing serious injury to a child or adult, and serious

damage to the product. Use only with a cart, stand, tripod,

bracket, or table recommended by the manufacturer, or sold

with the product. Any mounting of the product should

follow the manufacturer’s instructions, and should use a

mounting accessory recommended by the manufacturer.

9 A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven

surfaces may cause the product and cart

combination to overturn.

10 Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the

product and to protect it from overheating, and these

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or other similar surface. This product should not

be placed in a built-in installation such as a bookcase or rack

unless proper ventilation is provided or the manufacturer’s

instructions have been adhered to.

11 Power Sources – This product should be operated only from

the type of power source indicated on the marking label. If

you are not sure of the type of power supply to your home,

consult your product dealer or local power company. For

products intended to operate from battery power, or other

sources, refer to the operating instructions.

12 Grounding or Polarization – This product may be equipped

with a polarized alternating current line plug (a plug having

one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

13 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and the

point where they exit from the product.

14 Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

15 Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from touching

such power lines or circuits as contact with them might be

fatal.

16 Overloading – Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result

in a risk of fire or electric shock.

17 Object and Liquid Entry – Never push objects of any kind

into this product through openings as they may touch

dangerous voltage points or short-out parts that could result

in a fire or electric shock. Never spill liquid of any kind on

the product.

18 Servicing – Do not attempt to service this product yourself

as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

19 Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the

product,

c) If the product has been exposed to rain or water,

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

00_RXV550_U_EN.book Page i Tuesday, February 17, 2004 9:21 AM

IMPORTANT SAFETY INSTRUCTIONS

ii

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC – NATIONAL ELECTRICAL CODE

d) If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the product to its normal

operation,

e) If the product has been dropped or damaged in any

way, and

f) When the product exhibits a distinct change in perfor-

mance - this indicates a need for service.

20 Replacement Parts – When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer or have the same

characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock, or other

hazards.

21 Safety Check – Upon completion of any service or repairs to

this product, ask the service technician to perform safety

checks to determine that the product is in proper operating

condition.

22 Wall or Ceiling Mounting – The unit should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

23 Heat – The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

24 Outdoor Antenna Grounding – If an outside antenna or

cable system is connected to the product, be sure the antenna

or cable system is grounded so as to provide some

protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA 70,

provides information with regard to proper grounding of the

mast and supporting structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to grounding

electrodes, and requirements for the grounding electrode.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and, in particular, specifies

that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as

practical.

FCC INFORMATION (for US customers)

1 IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC, to

use the product.

2 IMPORTANT: When connecting this product to

accessories and/or another product use only high quality

shielded cables. Cable/s supplied with this product MUST

be used. Follow all installation instructions. Failure to

follow instructions could void your FCC authorization to

use this product in the USA.

3 NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15

for Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will

not result in harmful interference with other electronic

devices.

This equipment generates/uses radio frequencies and, if

not installed and used according to the instructions found

in the users manual, may cause interference harmful to the

operation of other electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this

product is found to be the source of interference, which

can be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

00_RXV550_U_EN.book Page ii Tuesday, February 17, 2004 9:21 AM

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

iii

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this sound system in a well ventilated, cool,

dry, clean place — away from direct sunlight, heat

sources, vibration, dust, moisture, and/or cold.

Allow ventilation space of at least 30 cm on the top,

20 cm on the left and right, and 20 cm on the back of

this unit.

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds.

4 Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this unit

in a environment with high humidity (i.e. a room with

a humidifier) to prevent condensation inside this

unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may

fall onto this unit and/or this unit may be exposed to

liquid dripping or splashing. On the top of this unit,

do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall

and liquid may cause electrical shock to the user

and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If

the temperature inside this unit rises, it may cause

fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than specified

is dangerous and may cause fire, damage to this

unit, and/or personal injury. YAMAHA will not be

held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, disconnect the

power cord from the wall outlet during an electrical

storm.

14 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

15 When not planning to use this unit for long periods

of time (i.e. vacation), disconnect the AC power plug

from the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding that

this unit is faulty.

17 Before moving this unit, press STANDBY/ON to set

this unit in the standby mode, and disconnect the

AC power plug from the wall outlet.

18 VOLTAGE SELECTOR (Asia and General models

only)

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local main voltage BEFORE

plugging into the AC main supply. Voltages are:

Asia model ...................... 220/230-240 V AC, 50/60 Hz

General model .. 110/120/220/230-240 V AC, 50/60 Hz

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association's Consumer

Electronics Group want you to get the most out of your

equipment by playing it at a safe level. One that lets the sound

come through loud and clear without annoying blaring or

distortion - and, most importantly, without affecting your

sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YA M A H A and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit itself

is turned off. This state is called the standby mode. In this

state, this unit is designed to consume a very small quantity of

power.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

00_RXV550_U_EN.book Page iii Tuesday, February 17, 2004 9:21 AM

1

English

PREPARATIONINTRODUCTION

BASIC

OPERATION

SOUND FIELD

PROGRAMS

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

FEATURES............................................................. 2

GETTING STARTED............................................ 3

Supplied accessories .................................................. 3

Installing batteries in the remote control ................... 3

CONTROLS AND FUNCTIONS ......................... 4

Front panel ................................................................. 4

Remote control........................................................... 6

Using the remote control ........................................... 7

Front panel display .................................................... 8

Rear panel ................................................................ 10

SPEAKER SETUP ............................................... 11

Speaker placement ................................................... 11

Speaker connections ................................................ 12

CONNECTIONS .................................................. 14

Before connecting components................................ 14

Connecting video components................................. 15

Connecting audio components................................. 18

Connecting the antennas.......................................... 19

Connecting the power supply cord .......................... 20

Turning on the power............................................... 22

BASIC SETUP...................................................... 23

Using the BASIC SETUP menu.............................. 23

PLAYBACK.......................................................... 26

Basic operations....................................................... 26

Selecting sound field programs ............................... 28

Selecting input modes.............................................. 32

TUNING ................................................................ 34

Automatic and manual tuning.................................. 34

Presetting stations .................................................... 35

Selecting preset stations........................................... 37

Exchanging preset stations ...................................... 38

RECORDING ....................................................... 39

SOUND FIELD PROGRAM

DESCRIPTIONS...............................................40

For movie/video sources.......................................... 40

For music sources .................................................... 42

ADVANCED OPERATIONS ..............................43

Using the sleep timer ............................................... 43

Manually adjusting speaker levels........................... 44

Using the test tone ................................................... 44

SET MENU ............................................................45

Using SET MENU................................................... 46

1 SOUND MENU.................................................... 47

2 INPUT MENU...................................................... 49

3 OPTION MENU................................................... 50

REMOTE CONTROL FEATURES ...................51

Control area ............................................................. 51

Setting manufacturer codes...................................... 52

Controlling other components ................................. 53

Clearing setup manufacturer codes.......................... 54

ZONE 2

(U.S.A., Canada and Australia models

only) ....................................................................55

Zone 2 connections .................................................. 55

Remote controlling Zone 2 ...................................... 56

EDITING SOUND FIELD PARAMETERS ......58

What is a sound field ............................................... 58

Changing parameter settings ................................... 58

SOUND FIELD PARAMETER

DESCRIPTIONS...............................................60

TROUBLESHOOTING .......................................62

RESETTING THE FACTORY PRESETS ........66

GLOSSARY...........................................................67

Audio formats .......................................................... 67

Sound field programs............................................... 68

Audio information ................................................... 68

Video signal information ......................................... 69

SPECIFICATIONS...............................................70

CONTENTS

INTRODUCTION

PREPARATION

BASIC OPERATION

SOUND FIELD PROGRAMS

ADVANCED OPERATION

ADDITIONAL INFORMATION

00_RXV550_U_EN.book Page 1 Tuesday, February 17, 2004 9:21 AM

FEATURES

2

Built-in 6-channel power amplifier

◆ Minimum RMS output power

(0.06% THD, 20 Hz – 20 kHz, 8Ω)

Front: 90 W + 90 W

Center: 90 W

Surround: 90 W + 90 W

Surround back: 90 W

Sound field features

◆ Proprietary YAMAHA technology for the creation of

sound fields

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS ES Matrix 6.1, Discrete 6.1, DTS Neo:6,

DTS 96/24 decoder

◆ Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic

IIx decoder

◆ Virtual CINEMA DSP

◆ SILENT CINEMA

™

Sophisticated AM/FM tuner

◆ 40-station random access preset tuning

◆ Automatic preset tuning

◆ Preset station shifting capability (preset editing)

Other features

◆ 192-kHz/24-bit D/A converter

◆ A SET MENU which provides you with items for

optimizing this unit for your audio/video system

◆ 6 additional input jacks for discrete multi-channel input

◆ S-Video signal input/output capability

◆ Component video input/output capability

◆ Video signal conversion (Composite video ↔ S-Video)

capability for monitor out

◆ Optical and coaxial digital audio signal jacks

◆ Sleep timer

◆ Cinema and music night listening modes

◆ Remote control with preset manufacturer codes

◆ Zone 2 custom installation facility (U.S.A., Canada and

Australia models only)

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In

case of differences between the manual and product, the product has priority.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol

are trademarks of Dolby Laboratories.

“SILENT CINEMA” is a trademark of YAMAHA

CORPORATION.

“DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks of

Digital Theater Systems, Inc.

FEATURES

00_RXV550_U_EN.book Page 2 Tuesday, February 17, 2004 9:21 AM

GETTING STARTED

3

English

INTRODUCTION

Please check that you received all of the following parts.

1 Press the part and slide the battery

compartment cover off.

2 Insert four supplied batteries (AAA, R03,

UM-4) according to the polarity markings

(+ and –) on the inside of the battery

compartment.

3 Slide the cover back until it snaps into place.

Notes on batteries

• Change all of the batteries if you notice the condition like; the

operation range of the remote control decreases, the indicator

does not flash or its light becomes dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

GETTING STARTED

Supplied accessories

TRANSMITCODE SET

STANDBY

SYSTEM

POWER

CD

MD/CD-R

TUNER

V-AU X

DVD

AMP

POWERPOWER

REC

AUDI O

MUTE

MENUTITLE

VOLUME

DISC SKIP

SET MENU

LEVEL

A/B/C/D/E

FREQ/RDS

EONSTARTMODE PTY SEEK

TEST

STRAIGHT

ROCKJAZZHALLSTEREO

4321

8

10

7

09

65

ENTER

MOVIETV THTRMUSIC ENTERTAIN

EX/ESNIGHTq/DTS

EFFECT

DISPLAYRETURN

TV MUTE TV INPUT

TV VOL TV CH

AVTV

SELECT

VCR

DTV/CBL

MULTI CH IN

SLEEP

PRESET/CH

RAV251

WC55290 EU

Remote control

Batteries (4)

(AAA, R03, UM-4)

Indoor FM antenna

(U.S.A., Canada, China, Asia

and General models)

AM loop antenna

75-ohm/300-ohm antenna

adapter (U.K. model only)

Indoor FM antenna

(U.K., Europe, Australia

and Korea models)

Installing batteries in the remote

control

1

3

2

If the remote control is without batteries for more than

2 minutes, or if exhausted batteries remain in the

remote control, the contents of the memory may be

cleared. When the memory is cleared, insert new

batteries, set up the manufacturer code and program

any acquired functions that may have been cleared.

00_RXV550_U_EN.book Page 3 Tuesday, February 17, 2004 9:21 AM

CONTROLS AND FUNCTIONS

4

1 STANDBY/ON

Turns on this unit or sets it to the standby mode. When you

turn on this unit, you will hear a click and there will be a 4

to 5-second delay before this unit can reproduce sound.

In standby mode, this unit consumes a small amount of power in

order to receive infrared-signals from the remote control.

2 Remote control sensor

Receives signals from the remote control.

3 Front panel display

Shows information about the operational status of this

unit.

4 A/B/C/D/E (NEXT)

Selects one of the 5 preset station groups (A to E) when

the unit is in tuner mode.

Selects the speaker channel to be adjusted when the unit is

not in tuner mode.

5 PRESET/TUNING l / h (LEVEL –/+)

Selects preset station number 1 to 8 when the colon (:) is

displayed next to the band indication in the front panel

display when the unit is in tuner mode. Selects the tuning

frequency when the colon (:) is not displayed.

Adjusts the level of the speaker channel selected using

A/B/C/D/E (NEXT) when the unit is not in tuner mode.

6 MEMORY (MAN’L/AUTO FM)

Stores a station in the memory. Hold down this button for

more than 3 seconds to start automatic preset tuning.

7 TUNING MODE (AUTO/MAN’L MONO)

Switches between automatic tuning (AUTO indicator on)

and manual tuning (AUTO indicator off).

8 VIDEO AUX jacks

Input audio and video signals from a portable external

source such as a game console. To reproduce source

signals from these jacks, select V-AUX as the input source.

9 VOLUME

Controls the output level of all audio channels.

This does not affect the REC OUT level.

CONTROLS AND FUNCTIONS

Front panel

AUTO/MAN'L MONOMAN'L/AUTO FMLEVELNEXTEDIT

EFFECT

MEMORYFM/AMPRESET/TUNING

A/B/C/D/E

PROGRAM

l PRESET/TUNING h

TUNING MODE

INPUT MODETONE CONTROLSTRAIGHT

SPEAKERS

PHONES

SILENT CINEMA

STANDBY

/ON

BA

MULTI CH

INPUT

VOLUME

INPUT

VIDEO L AUDIO R

VIDEO AUX

2134576

GHIEDB

9

8

0AC F

RDS MODE/FREQ EON

MODE

PTY SEEK

START

KLMJ

(U.S.A. model)

(U.K. and Europe models only)

Note

00_RXV550_U_EN.book Page 4 Tuesday, February 17, 2004 9:21 AM

CONTROLS AND FUNCTIONS

5

English

INTRODUCTION

0 PHONES (SILENT CINEMA) jack

Outputs audio signals for private listening with

headphones. When you connect headphones, no signals

are output to the OUTPUT jacks or to the speakers.

All Dolby Digital and DTS audio signals are mixed down

to the left and right headphone channels.

A SPEAKERS A/B

Turns on or off the set of front speakers connected to the A

and/or B terminals on the rear panel each time the

corresponding button is pressed.

B PRESET/TUNING (EDIT)

Switches the function of PRESET/TUNING l / h

(LEVEL –/+) between selecting preset station numbers

and tuning.

C STRAIGHT (EFFECT)

Switches the sound fields off or on. When STRAIGHT is

selected, input signals (2-channel or multi-channel) are

output directly from their respective speakers without

effect processing.

D FM/AM

Switches the reception band between FM and AM.

E PROGRAM

Use to select sound field programs or adjust the bass/treble

balance (in conjunction with TONE CONTROL).

F TONE CONTROL

Use to adjust the bass/treble balance for the front left and

right speakers (see page 27).

G INPUT MODE

Sets the priority (AUTO, DTS, ANALOG) for the type of

signals received when one component is connected to two

or more of this unit’s input jacks (see page 32).

H INPUT selector

Selects the input source you want to listen to or watch.

I MULTI CH INPUT

Selects the source connected to the MULTI CH INPUT

jacks. When selected, the MULTI CH INPUT source takes

priority over the source selected with INPUT (or the input

selector buttons on the remote control).

■ U.K. and Europe models only

J RDS MODE/FREQ

Press this button when the unit is receiving an RDS station

to cycle the display between the PS mode, PTY mode, RT

mode, CT mode (if the station offers those RDS data

services) and/or the frequency display.

K PTY SEEK MODE

Press this button to set the unit to the PTY SEEK mode.

L PTY SEEK START

Press this button to begin searching for a station after the

desired program type has been selected in the PTY SEEK

mode.

M EON

Press this button to select a radio program type (NEWS,

INFO, AFFAIRS, SPORT) to tune in automatically.

00_RXV550_U_EN.book Page 5 Tuesday, February 17, 2004 9:21 AM

CONTROLS AND FUNCTIONS

6

This section describes the function of each control on the

remote control used to control this unit. To operate other

components, see “REMOTE CONTROL FEATURES” on

page 51.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 CODE SET

Use to set up manufacturer codes (see page 52).

3 Input selector buttons

Select the input source and change the control area.

4 Sound field program / numeric buttons (1 - 8)

Use to select sound field programs.

Use numbers 1 through 8 to select preset stations when the

unit is in tuner mode.

5 NIGHT

Turns on or off the night listening modes (page 31).

6 LEVEL

Selects the speaker channel to be adjusted and sets the

level.

7 Cursor buttons u / d / j / i / SELECT

Use to select and adjust sound field program parameters or

SET MENU items.

Press u / d to select preset station numbers when the unit

is in tuner mode.

8 TEST (RETURN)

Outputs the test tone to adjust the speaker levels.

Returns to the previous menu level when adjusting the

SET MENU parameters.

9 TRANSMIT indicator

Flashes while the remote control is sending signals.

0 STANDBY

Sets this unit in the standby mode.

A SYSTEM POWER

Turns on the power of this unit.

B SLEEP

Sets the sleep timer.

C MULTI CH IN

Selects MULTI CH INPUT when using an external

decoder (etc.).

D AMP

Selects the AMP mode. You must select the AMP mode to

control the main unit.

E VOLUME –/+

Increases or decreases the volume level.

F MUTE

Mutes the sound. Press again to restore the audio output to

the previous volume level.

G EX/ES

Switches between 5.1 or 6.1-channel playback of multi-

channel software.

Remote control

TRANSMITCODE SET

STANDBY

SYSTEM

POWER

CD

MD/CD-R

TUNER

V-AUX

DVD

AMP

POWERPOWER

REC

AUDIO

MUTE

MENUTITLE

VOLUME

DISC SKIP

FREQ/RDS

EONSTART

SET MENU

LEVEL

A/B/C/D/E

MODE PTY SEEK

TEST

STRAIGHT

ROCKJAZZHALLSTEREO

4321

8

10

7

09

65

ENTER

MOVIETV THTRMUSIC ENTERTAIN

EX/ESNIGHTq/DTS

EFFECT

DISPLAYRETURN

TV MUTE TV INPUT

TV VOL TV CH

AVTV

SELECT

VCR

DTV/CBL

MULTI CH IN

SLEEP

PRESET/CH

9

0

A

B

C

D

E

F

H

I

J

1

2

3

4

5

7

8

6

G

00_RXV550_U_EN.book Page 6 Tuesday, February 17, 2004 9:21 AM

CONTROLS AND FUNCTIONS

7

English

INTRODUCTION

H STRAIGHT (EFFECT)

Switches the sound fields off or on. When STRAIGHT is

selected, input signals (2-channel or multi-channel) are

output directly from their respective speakers without

effect processing.

I SET MENU (A/B/C/D/E)

Activates the SET MENU function.

Selects preset station groups when the unit is in tuner

mode.

■ U.K. and Europe models only

J RDS tuning buttons

FREQ/RDS

Press this button when the unit is receiving an RDS station

to cycle the display between the PS mode, PTY mode, RT

mode, CT mode (if the station offers those RDS data

service) and/or the frequency display.

PTY SEEK MODE

Press this button to set the unit to the PTY SEEK mode.

PTY SEEK START

Press this button to begin searching for a station after the

desired program type has been selected in the PTY SEEK

mode.

EON

Press this button to select a radio program type (NEWS,

INFO, AFFAIRS, SPORT) to tune in automatically.

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the main unit during operation.

■ Handling the remote control

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– high humidity such as near a bath

– high temperature such as near a heater or stove

– extremely low temperatures

– dusty places

Using the remote control

RDS MODE/FREQ EON

MODE

PTY SEEK

START

AUTO/MAN'L MONOMAN'L/AUTO FMLEVELNEXTEDIT

EFFECT

MEMORYFM/AMPRESET/TUNING

A/B/C/D/E

PROGRAM

l PRESET/TUNING h

TUNING MODE

INPUT MODETONE CONTROLSTRAIGHT

SPEAKERS

PHONES

SILENT CINEMA

STANDBY

/ON

BA

MULTI CH

INPUT

VOLUME

INPUT

VIDEO L AUDIO R

VIDEO AUX

30 30

TRANSMITCODE SET

STANDBY

SYSTEM

POWER

CD

MD/CD-R

TUNER

V-AUX

DVD

AMP

POWERPOWER

REC

AUDIO

MUTE

MENUTITLE

VOLUME

DISC SKIP

SET MENU

LEVEL

A/B/C/D/E

TEST

STRAIGHT

ROCKJAZZHALLSTEREO

4321

8

10

7

09

65

ENTER

MOVIETV THTRMUSICENTERTAIN

EX/ESNIGHTq/DTS

EFFECT

DISPLAYRETURN

TV MUTE TV INPUT

TV VOL TV CH

AVTV

SELECT

VCR

DTV/CBL

MULTI CH IN

SLEEP

PRESET/CH

Approximately 6 m (20 ft)

00_RXV550_U_EN.book Page 7 Tuesday, February 17, 2004 9:21 AM

CONTROLS AND FUNCTIONS

8

1 Decoder indicators

When any of this unit’s decoders function, the respective

indicator lights up.

2 SILENT CINEMA indicator

Lights up when headphones are connected and a sound

field program is selected (see page 27).

3 NIGHT indicator

Lights up when you select night listening mode.

4 Input source indicators

A cursor lights to show the current input source.

5 Sound field indicators

Light to indicate the active DSP sound fields.

6 CINEMA DSP indicator

Lights up when you select a CINEMA DSP sound field

program.

7 AUTO indicator

Lights up to indicate that automatic tuning is possible.

8 TUNED indicator

Lights up when this unit is tuned into a station.

9 STEREO indicator

Lights up when this unit is receiving a strong signal for an

FM stereo broadcast while the AUTO indicator is lit.

0 MEMORY indicator

Blinks to show that a station can be stored.

A MUTE indicator

Blinks while the MUTE function is on.

B VOLUME level indication

Indicates the volume level.

C PCM indicator

Lights up when this unit is reproducing PCM (pulse code

modulation) digital audio signals.

D VIRTUAL indicator

Lights up when Virtual CINEMA DSP is active (see

page 32).

E Headphones indicator

Lights up when headphones are connected.

F SP A B indicators

Light up according to the set of front speakers selected.

Both indicators light up when both sets of speakers are

selected.

G SLEEP indicator

Lights up while the sleep timer is on.

H HiFi DSP

Lights when you select a HiFi DSP sound field program.

I Multi-information display

Shows the current sound field program name and other

information when adjusting or changing settings.

J 96/24 indicator

Lights up when a DTS 96/24 signal is input to this unit.

Front panel display

CDTUNER

MD/CD-R

DVD

HiFi DSP

DTV/CBL

V-AUXVCR

96

24

q

PL

q

EX

q

PL

MATRIX DISCRETE

SILENT CINEMA NIGHT

ZONE2

PTY HOLD AUTO

PS RT CT EONPTY

TUNED STEREO MUTE

VOLUME

MEMORY

SLEEP

VIRTUAL

PCM

q

PL x

A B

SP

ft

mS

dB

96/24

LFE

LCR

SL SB SR

q

DIGITAL

t

123456 780AB9

FG

M

N

HI KLJEDC

(U.S.A., Canada and

Australia models only)

(U.K. and Europe models only)

Presence DSP sound field

Listening position

Left surround

DSP sound field

Right surround

DSP sound field

Surround back DSP sound field

00_RXV550_U_EN.book Page 8 Tuesday, February 17, 2004 9:21 AM

CONTROLS AND FUNCTIONS

9

English

INTRODUCTION

K LFE indicator

Lights up when the input signal contains the LFE signal.

L Input channel indicators/speaker indicators

Indicate the channel components of the current digital

input signal.

Indicate the number of speakers connected in SPEAKERS

(page 24), or indicate the channel being adjusted in SP

LEVEL (page 48).

M ZONE 2 indicator

(U.S.A., Canada and Australia models only)

Lights up when Zone 2 power is on.

N RDS indicators

(U.K. and Europe models only)

The name(s) of the RDS data offered by the currently

received RDS station light(s) up.

EON lights up when an RDS station that offers the EON

data service is being received.

PTY HOLD lights up while searching for stations in the

PTY SEEK mode.

00_RXV550_U_EN.book Page 9 Tuesday, February 17, 2004 9:21 AM

CONTROLS AND FUNCTIONS

10

1 DIGITAL INPUT jacks

See pages 15, 17 and 18 for details.

2 MULTI CH INPUT jacks

See page 16 for connection information.

3 Video component jacks

See pages 15 and 17 for connection information.

4 REMOTE IN/OUT jacks

(U.S.A., Canada and Australia models only)

See page 55 for details.

5 CONTROL OUT jack

(U.S.A., Canada and Australia models only)

This is a control expansion terminal for commercial use.

6 AC OUTLET(S)

Use to supply power to your other A/V components (see

page 20).

7 DIGITAL OUTPUT jack

See page 18 for details.

8 Audio component jacks

See page 18 for connection information.

9 ZONE 2 OUTPUT jacks

(U.S.A., Canada and Australia models only)

See page 55 for details.

0 SUB WOOFER OUTPUT jack

See page 13 for connection information.

A Antenna terminals

See page 19 for connection information.

B Speaker terminals

See page 13 for connection information.

C IMPEDANCE SELECTOR switch

See page 21.

< Asia and General models only >

FREQUENCY STEP switch

See page 19.

VOLTAGE SELECTOR

See page 20.

Rear panel

SPEAKERS

FRONT

CENTER

SURROUND

SURROUND BACK

R

L

CENTER

SUB

WOOFER

MONITOR OUT

MULTI CH INPUT

OUTPUT

AUDIO

VIDEO

S VIDEO

DVD

DTV

/CBL

VIDEO

R

L

R

L

IN

(

PLAY

)

OUT

(

REC

)

MD

/CD-R

CD

OUT

ZONE 2

VCR

VIDEO

IN

FRONT

SURROUND

TUNER

AM

ANT

GND

COMPONENT VIDEO

P

R

DVD

MONITOR

OUT

DTV

/CBL

P

B

Y

DIGITAL

OUTPUT

DIGITAL

INPUT

OPTICAL

MD/CD-R

DVD

DTV/CBL

CD

COAXIAL

+

–

+

–

+

––

+

–

A

B

CONTROL

OUT

REMOTE

IN

OUT

+12V

15mA MAX.

FM

ANT

OPTICAL

SUB

WOOFER

S VIDEO

R

L

ZONE 2

IMPEDANCE SELECTOR

AC OUTLETS

SWITCHED

MD/CD-R

75Ω UNBAL.

12 3 5 64

7890A B C

(U.S.A. model)

00_RXV550_U_EN.book Page 10 Tuesday, February 17, 2004 9:21 AM

SPEAKER SETUP

11

English

PREPARATION

The speaker layout below shows the standard ITU-R

speaker setting. You can use it to enjoy CINEMA DSP

and multi-channel audio sources.

Front speakers (FR and FL)

The front speakers are used for the main source sound plus

effect sounds. Place these speakers an equal distance from

the ideal listening position. The distance of each speaker

from each side of the video monitor should be the same.

Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). If for some reason it is not practical

to use a center speaker, you can do without it. Best results,

however, are obtained with the full system. Align the front

face of the center speaker with the front face of your video

monitor. Place the speaker centrally between the front

speakers and as close to the monitor as possible, such as

directly over or under it.

Surround speakers (SR and SL)

The surround speakers are used for effect and surround

sounds. Place these speakers behind your listening

position, facing slightly inwards, about 1.8 m (6 ft) above

the floor.

Surround back speaker (SB)

The surround back speaker supplements the surround

speakers and provides for more realistic front-to-back

transitions. Place this speaker directly behind the listening

position and at the same height as the surround speakers.

Subwoofer

The use of a subwoofer, such as the YAMAHA Active

Servo Processing Subwoofer System, is effective not only

for reinforcing bass frequencies from any or all channels,

but also for high fidelity reproduction of the LFE (low-

frequency effect) channel included in Dolby Digital and

DTS software. The position of the subwoofer is not so

critical, because low bass sounds are not highly

directional. But it is better to place the subwoofer near the

front speakers. Turn it slightly toward the center of the

room to reduce wall reflections.

SPEAKER SETUP

Speaker placement

60˚

30˚

SB

FL

FR

C

SL

SR

80˚

SL

1.8 m (6 ft)

00_RXV550_U_EN.book Page 11 Tuesday, February 17, 2004 9:21 AM

12

SPEAKER SETUP

Be sure to connect the left channel (L), right channel (R),

“+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the

polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

• If you will use 6 ohm speakers, be sure to set

this unit’s speaker impedance setting to 6

ohms before using (see page 21).

• Before connecting the speakers, make sure that the

power of this unit is off.

• Do not let the bare speaker wires touch each other or do

not let them touch any metal part of this unit. This

could damage this unit and/or speakers.

• Use magnetically shielded speakers. If this type of

speakers still creates the interference with the monitor,

place the speakers away from the monitor.

A speaker cord is actually a pair of insulated cables

running side by side. One cable is colored or shaped

differently, perhaps with a stripe, groove or ridges.

Connect the striped (grooved, etc.) cable to the “+” (red)

terminals on this unit and your speaker. Connect the plain

cable to the “–” (black) terminals.

1 Remove approximately 10 mm (3/8") of

insulation from the end of each speaker

cable.

2 Twist the exposed wires of the cable together

to prevent short circuits.

3 Unscrew the knob.

4 Insert one bare wire into the hole in the side

of each terminal.

5 Tighten the knob to secure the wire.

■ Banana plug connections

(With the exception of U.K., Europe and Asia models)

First, tighten the knob and then insert the banana plug

connector into the end of the corresponding terminal.

Speaker connections

CAUTION

10 mm (3/8")

1

2

Red: positive (+)

Black: negative (–)

3

4

5

Banana plug

(With the exception of U.K., Europe

and Asia models)

00_RXV550_U_EN.book Page 12 Tuesday, February 17, 2004 9:21 AM

13

English

SPEAKER SETUP

PREPARATION

■ FRONT terminals

Connect one or two speaker systems to these terminals. If

you use only one speaker system, connect it to either the

FRONT A or B terminals.

The Canada model cannot output to two separate speaker systems

simultaneously.

■ CENTER terminals

Connect a center speaker to these terminals.

■ SURROUND terminals

Connect surround speakers to these terminals.

■ SUB WOOFER jack

Connect a subwoofer with built-in amplifier, such as the

YAMAHA Active Servo Processing Subwoofer System,

to this jack.

■ SURROUND BACK terminals

Connect a surround back speaker to these terminals.

SPEAKERS

FRONT

CENTER

SURROUND

SURROUND BACK

R

L

OUTPUT

+

–

+

–

+

––

+

–

A

B

SUB

WOOFER

2 3 6 71

54

Subwoofer

system

Center

speaker

Front speakers (A)

Surround back

speaker

LeftRight

Surround speakers

Front

speakers

(B)

(U.S.A. model)

Note

1

2

3

4

5

7

6

Speaker layout

00_RXV550_U_EN.book Page 13 Tuesday, February 17, 2004 9:21 AM

CONNECTIONS

14

Do not connect this unit or other components to the mains

power until all connections between components are

complete.

■ Cable indications

■ Analog jacks

You can input analog signals from audio components by

connecting audio pin cable to the analog jacks on this unit.

Connect red plugs to the right jacks and white plugs to the

left jacks.

■ Digital jacks

This unit has digital jacks for direct transmission of digital

signals through either coaxial or fiber optic cables. You

can use the digital jacks to input PCM, Dolby Digital and

DTS bitstreams. When you connect components to both

the COAXIAL and OPTICAL jacks, priority is given to

the input signals from the COAXIAL jack. All digital

input jacks are compatible with 96-kHz sampling digital

signals.

This unit handles digital and analog signals independently. Thus

audio signals input to the analog jacks are only output to the

analog OUT (REC) jacks. Likewise audio signals input to the

digital (OPTICAL or COAXIAL) jacks are only output to the

DIGITAL OUTPUT jack.

Dust protection cap

Pull out the cap from the optical jack before you connect

the fiber optic cable. Do not discard the cap. When you are

not using the optical jack, be sure to put the cap back in

place. This cap protects the jack from dust.

■ Video jacks

This unit has three types of video jacks. Connection

depends on the availability of input jacks on your monitor.

The signals input through the S VIDEO jacks on this unit

are automatically converted for output through the

VIDEO jacks. When V CONV. is set to ON (see page 50),

signals input through the VIDEO jacks can be output

through the S VIDEO jacks.

VIDEO jack

For conventional composite video signals.

S VIDEO jack

For S-Video signals, separated into luminance (Y) and

color (C) video signals to achieve high-quality color

reproduction.

COMPONENT VIDEO jacks

For component signals, separated into luminance (Y) and

color difference (P

B, PR) to provide the best quality in

picture reproduction.

When signals are input through both the S VIDEO and VIDEO

jacks, signals input through the S VIDEO jack have priority.

CONNECTIONS

Before connecting components

Note

CAUTION

S

V

O

V

L

R

C

left analog cables

right analog cables

optical cables

coaxial cables

video cables

S-Video cables

For analog signals

For digital signals

For video signals

Note

VIDEO

S VIDEO

COMPONENT VIDEO

P

R

P

B

Y

S VIDEO

VIDEO

COMPONENT

VIDEO

Signal flow inside this unit

Only when V CONV. is set to ON

(see page 50).

Output

(MONITOR OUT)

Input

00_RXV550_U_EN.book Page 14 Tuesday, February 17, 2004 9:21 AM

15

English

CONNECTIONS

PREPARATION

■ Connections for DVD playback

Connecting video components

MONITOR OUT

AUDIO

VIDEO

S VIDEO

DVD

VIDEO

R

L

VIDEO

COMPONENT VIDEO

PR

DVD

MONITOR

OUT

PB

Y

DVD

S VIDEO

LR

O

DVD player

Video

monitor

(U.S.A. model)

Optical out

Video out

Audio out

Video in

00_RXV550_U_EN.book Page 15 Tuesday, February 17, 2004 9:21 AM

16

CONNECTIONS

■ Connecting to the MULTI CH INPUT jacks

This unit is equipped with 6 additional input jacks (left and right FRONT, CENTER, left and right SURROUND and

SUB WOOFER) for discrete multi-channel input from a multi-format player, external decoder, sound processor or pre-

amplifier.

Connect the output jacks on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to

match the left and right outputs to the left and right input jacks for the front and surround channels.

• When you select MULTI CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you

cannot select sound field programs.

• This unit does not redirect signals input to the MULTI CH INPUT jacks to accommodate for missing speakers. We recommend that

you connect at least a 5.1-channel speaker system before using this feature.

• When headphones are used, only front left and right channels are output.

Notes

CENTER

SUB

WOOFER

MULTI CH INPUT

FRONT

SURROUND

R

L

LR

Multi-format player/

External decoder

Front

out

Surround

out

Subwoofer

out

Center

out

(U.S.A. model)

00_RXV550_U_EN.book Page 16 Tuesday, February 17, 2004 9:21 AM

La page charge ...

Yamaha RX-550 Le manuel du propriétaire

Ce manuel convient également à

Yamaha RX-550 Le manuel du propriétaire

dans d''autres langues

Documents connexes