Briggs & Stratton ELITE 7000 WATT Manuel utilisateur

Marque: Briggs & Stratton

Modèle: ELITE 7000 WATT

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

01894-1

(7000W)

Operator’s Manual

Manuel de l'utilisateur

Manual del Operario

Questions? Help is just a moment away!

Vous avez des questions? Vous n'avez pas besoin d'aller

loin pour trouver de l'aide!

Preguntas? La ayuda es justa un momento lejos!

Call: Generator Helpline

Appelez: Ligne d'assistance de Générateur

Llame: Línea Directa del Generador

1-800-743-4115 M-F 8-5 CT

web: www.briggsandstratton.com

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON,WISCONSIN, U.S.A.

Manual No. 196746GS

Revision B (06/14/2006)

Before using this product, read this

manual and follow all Safety Rules and

Operating Instructions.

WARNING

Antes de utilizar el producto, lea este

manual y siga todas las Reglas de

Seguridad e Instrucciones de Uso.

ADVERTENCIA

Avant d’utiliser ce produit, veuillez lire

le manuel et suivre toutes les directives

relatives à la sécurité et à l’utilisation.

AVERTISSEMENT

SAFETY RULES

TABLE OF CONTENTS

Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Know Your Generator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

EQUIPMENT

DESCRIPTION

Read this manual carefully and become familiar

with your generator. Know its applications, its

limitations and any hazards involved.

This generator is an engine–driven, revolving field,

alternating current (AC) generator. It was designed to

supply electrical power for operating compatible electrical

lighting, appliances, tools and motor loads.The generator’s

revolving field is driven at about 3,600 rpm by a single-

cylinder engine.

CAUTION! DO NOT exceed the generator’s

wattage/amperage capacity. See “Don’t Overload

Generator”.

Every effort has been made to ensure that information in

this manual is accurate and current. However, we reserve

the right to change, alter or otherwise improve the product

and this document at any time without prior notice.

The Emission Control System for this generator is

warranted for standards set by the Environmental

Protection Agency and the California Air Resources Board.

For warranty information refer to the engine operator’s

manual.

SAFETY RULES

This is the safety alert symbol. It is used to

alert you to potential personal injury hazards.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION,WARNING), a pictorial and/or a

safety message to alert you to hazards. DANGER indicates

a hazard which, if not avoided, will result in death or

serious injury. WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, might

result in minor or moderate injury. CAUTION, when used

without the alert symbol, indicates a situation that could

result in equipment damage. Follow safety messages to

avoid or reduce the risk of injury or death.

Hazard Symbols and Meanings

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

Fire

Explosion

Toxic Fumes

Hot Surface

Operator’s Manual

Electrical Shock

Explosive Pressure

Chemical Burn

SAVE THESE INSTRUCTIONS

may be reproduced or transmitted in any form by any

means without the express written permission of Briggs &

Stratton Power Products Group, LLC.

SAFETY RULES

• This generator does not meet U. S. Coast Guard Regulation

33CFR-183 and should not be used on marine applications.

• Failure to use the appropriate U. S. Coast Guard approved

generator could result in bodily injury and/or property

damage.

WARNING

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• Wear protective goggles, rubber apron, and rubber gloves.

Storage batteries give off explosive hydrogen gas

during recharging.

Hydrogen gas stays near battery for a long time

after battery has been charged.

Slightest spark will ignite hydrogen and cause

explosion.

You can be blinded or severely injured.

Battery electrolyte fluid contains acid and is

extremely caustic.

Contact with battery fluid will cause severe

chemical burns.

DANGER

WHEN ADDING OR DRAINING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank.Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap and air cleaner are in place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• Do not tip engine or equipment at angle which causes fuel to

spill.

• This generator is not for use in mobile equipment or marine

applications.

WHEN TRANSPORTING OR REPAIRING

EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL

IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

• Operate generator ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate generator inside any building or enclosure

(even if doors or windows are open), including the generator

compartment of a recreational vehicle (RV).

Running generator gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide can cause nausea,

fainting or death.

WARNING

Using a generator indoors WILL KILL YOU

IN MINUTES.

Exhaust contains carbon monoxide, a

poison gas you cannot see or smell.

NEVER use in the home

or in partly enclosed

areas such as garages.

ONLY use outdoors and

far from open windows,

doors, and vents.

SAFETY RULES

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

Excessively high operating speeds increase risk of injury

and damage to generator.

Excessively low speeds impose a heavy load.

CAUTION

• See “Don’t Overload Generator”.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

Exceeding generators wattage/amperage capacity can

damage generator and/or electrical devices connected

to it.

CAUTION

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or call

1-800-743-4115.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust, dirt,

or corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and disconnect

them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

Improper treatment of generator can damage it and

shorten its life.

CAUTION

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Unintentional sparking can result in fire or

electric shock.

WARNING

• DO NOT touch hot surfaces and avoid hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (152 cm) clearance on all sides of generator

including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

Running engines produce heat.Temperature of

muffler and nearby areas can reach or exceed

150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

WARNING

• When using generator for backup power, notify utility

company. Use approved transfer equipment to isolate

generator from electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing

in water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

Generator produces powerful voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

WARNING

KNOW YOUR GENERATOR

Read this Operator’s Manual and safety rules before operating your generator.

Compare the illustrations with your generator, to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

12 Volt DC Receptacle — Use this receptacle with

battery charge cables to charge a 12 Volt battery.

120 Volt AC, 20 Amp Duplex Receptacles — May be

used to supply electrical power for the operation of 120Volt

AC, 20 Amp, single phase, 60 Hz electrical lighting, appliance,

tool and motor loads.

120/240 Volt AC, 30 Amp Locking Receptacle — May

be used to supply electrical power for the operation of

120 and/or 240 Volt AC, 30 Amp, single phase, 60 Hz

electrical lighting, appliance, tool and motor loads.

Air Cleaner —

Protects engine by filtering dust and debris

out of intake air.

Battery — Located behind plastic cover. 12 Volt DC sealed

battery provides power to start the engine.

Choke Lever — Used when starting a cold engine.

Circuit Breakers (AC) — The 120 Volt AC, 20A duplex

receptacles are provided with "push to reset" circuit

breakers to protect the generator against electrical overload.

Data Tag – Provides model, revision and serial number of

generator. Please have these readily available if calling for

assistance.

Fuel Tank — Capacity of seven (7) U.S. gallons.

Start Switch — Turn to start the engine.

Grounding Fastener — If required, please consult a

qualified electrician, electrical inspector, or local agency

having jurisdiction.

Oil Fill Cap — Add oil to engine here.

Spark Arrester Muffler — Exhaust muffler lowers engine

noise and is equipped with a spark arrester screen.

Rocker Switch Circuit Breaker — The 120/240 Volt AC,

30A locking receptacle is provided with a rocker switch circuit

breaker to protect the generator against electrical overload.

This switch also controls all receptacles.

Choke Lever

Rocker Switch Circuit

Breaker

Circuit Breakers (AC)

120 Volt AC, 20 Amp

Duplex Receptacles

120/240 Volt AC, 30 Amp

Locking Receptacle

12 Volt DC

Receptacle

Spark Arrester Muffler

Start Switch

Grounding

Fastener

Air Cleaner

Fuel Tank

Oil Fill Cap

Data Tag

Battery

ASSEMBLY

Your generator requires some assembly and is ready for

use after it has been properly serviced with the

recommended oil and fuel.

If you have any problems with the assembly of your

generator, please call the generator helpline at

1-800-743-4115. If calling for assistance, please have the

model, revision, and serial number from the data tag available.

See “Know Your Generator” for data tag location.

Unpacking the Generator

1. Set the carton on a rigid flat surface.

2. Open carton completely by cutting each corner from

top to bottom.

3. Remove all packing material, carton fillers, etc.

4. Remove generator from shipping carton.

Attach Handle

You will need two 1/2” or 13mm wrenches to attach handle.

1. Attach handle to right side of generator frame (viewing

unit from front), as shown in Figure 1, with a 60 mm

capscrew, flat washers, nylon washers, and lock nut.

NOTE: DO NOT overtighten. Handle must be able to

move up and down freely.

2. Raise handle and insert handle pin to move generator.

60mm Capscrew

Nylon Washers

Flat Washers

Lock Nut

Handle Pin

Figure 1 — Attach Handle

Nut

Washer

Nylon Washer

Handle Bracket

Nylon Washer

Handle Bracket

Washer

60mm Capscrew

Handle Pin

ASSEMBLY

BEFORE STARTING THE

ENGINE

Add Engine Oil

• Place generator on a level surface.

• Refer to engine operator’s manual and follow oil

recommendations and instructions.

NOTE: Check oil often during engine break–in. Refer to

engine operator’s manual for recommendations.

NOTE: The generator assembly rotates on a prelubricated

and sealed ball bearing that requires no additional

lubrication for the life of the bearing.

Add Fuel

NOTE: This gasoline engine is certified to operate on

gasoline. Exhaust Emission Control System: EM (Engine

Modifications).

1. Use clean, fresh, regular UNLEADED gasoline with a

minimum of 87 octane. DO NOT use fuel which

contains Methanol. DO NOT mix oil with fuel.

2. Clean area around fuel fill cap, remove cap.

3. Slowly add regular unleaded fuel to fuel tank. Be careful

not to overfill.Allow at least 2.25" of tank space for

fuel expansion (Figure 2).

4. Install fuel cap and let any spilled fuel evaporate before

starting engine.

Remove Cover on Start Switch

A protective plastic cover is placed over the start switch to

prevent the generator from being started.

• Open cap on battery float charger.

• Remove and discard plastic cover over the start switch

(Figure 3).

• Replace cap on battery float charger.

CAUTION

• Refer to engine operator’s manual for oil fill information.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

Any attempt to crank or start the engine before it has

been properly filled with the recommended oil will result

in equipment failure.

WHEN ADDING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank.Allow space for fuel expansion.

• Wait for spilled fuel to evaporate before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

Fuel

Tank

2.25” Air Space

Figure 2 - Fuel Expansion

Figure 3 — Remove Cover on Start Switch

• Replace “1.5” with “2.25” fuel fill level given in engine manual.

• Failure to follow this instruction may cause fuel to overexpand

and spill from tank.

Fill tank to approximately 2.25” below top of

neck to allow for fuel expansion.

WARNING

OPERATION

USING THE GENERATOR

System Ground

The generator has a system ground that connects the

generator frame components to the ground terminals on

the AC output receptacles.The system ground is connected

to the AC neutral wire (the neutral is bonded to the

generator frame).

Special Requirements

There may be Federal or State Occupational Safety and

Health Administration (OSHA) regulations, local codes, or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction.

• In some areas, generators are required to be registered

with local utility companies.

• If the generator is used at a construction site, there may

be additional regulations which must be observed.

Connecting to a Building’s Electrical

System

Connections for standby power to a building’s electrical

system must be made by a qualified electrician.The

connection must isolate the generator power from utility

power, and must comply with all applicable laws and

electrical codes.

Generator Location

Generator Clearance

Place generator in a well ventilated area, which will allow

for removal of deadly exhaust gas. DO NOT place

generator where exhaust gas could accumulate and enter

inside or be drawn into a potentially occupied building.

Ensure exhaust gas is kept away from any windows, doors,

ventilation intakes or other openings that can allow exhaust

gas to collect in a confined area (Figure 4). Prevailing winds

and air currents should be taken into consideration when

positioning generator.

Figure 4 — Generator Clearance

Exhaust Port

• When using generator for backup power, notify utility

company. Use approved transfer equipment to isolate

generator from electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing

in water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

Generator produces powerful voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

WARNING

• Keep at least 5 ft. (152 cm) clearance on all sides of generator

including overhead.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

WARNING

Using a generator indoors WILL KILL YOU

IN MINUTES.

Exhaust contains carbon monoxide, a

poison gas you cannot see or smell.

NEVER use in the home

or in partly enclosed

areas such as garages.

ONLY use outdoors and

far from open windows,

doors, and vents.

OPERATION

OPERATING THE

GENERATOR

Starting the Engine

IMPORTANT: Always unplug the battery float charger

before starting the generator.

Disconnect all electrical loads from the generator. Follow

start instruction steps in numerical order:

1. Make sure unit is on a level surface.

IMPORTANT: Failure to start and operate unit on a level

surface will cause the unit not to start or shut down during

operation.

2. Follow start instructions given in engine operator’s

manual and turn start switch on generator to “Start”

position (Figure 5).

To prolong the life of starter components, DO NOT

hold starter switch in “Start” position for more than

15 seconds, and pause for 1 minute.

NOTE: If engine starts but fails to run, or if unit shuts down

during operation, make sure unit is on a level surface and

check for proper oil level in crankcase.This unit may be

equipped with a low oil protection device. See engine

operator’s manual.

Jump Start Procedure

If the generator’s starting battery fails, use the following

instructions to jump start your generator.You can jump

start the generator using any 12 Volt automotive or utility

style storage battery.

1. Unscrew the fuse holder and remove the generator’s

10 Amp in-line fuse (Figure 6).Verify the fuse is good

or replace with a known good fuse. Reinstall fuse in

the fuse holder.

2. Slide the red rubber boot off the generator’s battery

terminal and push it onto the red wire, thus

uncovering the POSITIVE battery terminal.

Figure 6 — In-Line Fuse

Figure 5 — Starter Switch

• DO NOT touch hot surfaces and avoid hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (152 cm) clearance on all sides of generator

including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

Running engines produce heat.Temperature of

muffler and nearby areas can reach or exceed

150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

WARNING

OPERATION

3. Using standard automotive jumper cables, connect the

RED jumper cable clamp to the generator’s POSITIVE

battery terminal (Figure 7).

4. Connect the other RED jumper cable clamp to the

starting battery’s POSITIVE battery terminal.

5. Connect the BLACK jumper cable clamp to the

starting battery’s NEGATIVE battery terminal.

6. Connect the other BLACK jumper cable clamp to the

GROUNDING FASTENER on the generator, as shown

in Figure 7.

7. Start the generator as described in “Starting the

Engine” and remove jumper cables in reverse order of

connections.

8. Slide the red rubber boot back onto the generator’s

POSITIVE battery terminal.

If you have any questions, please call the Generator

Helpline at 1-800-743-4115, M-F 8-5 CT.

IMPORTANT: When jump starting, always wear proper eye

protection and never lean over battery. Inspect both

batteries before connecting booster cables. DO NOT jump

start a damaged battery. Be sure vent caps are tight and level.

Connecting Electrical Loads

• Let engine stabilize and warm up for a few minutes after

starting.

• Plug in and turn on the desired 120 and/or 240 Volt AC,

single phase, 60 Hz electrical loads.

• DO NOT connect 240 Volt loads to the 120 Volt

receptacles.

• DO NOT connect 3–phase loads to the generator.

• DO NOT connect 50 Hz loads to the generator.

• DO NOT OVERLOAD GENERATOR. See “Don’t

Overload Generator”.

Stopping the Engine

1. Unplug all electrical loads from generator panel

receptacles. NEVER start or stop engine with electrical

devices plugged in and turned on.

2. Let engine run at no–load for 30 seconds to stabilize

the internal temperatures of engine and generator.

3. Turn start switch to “Stop” position.

Charging a Battery

Your generator has the capability of recharging a discharged

12 Volt automotive or utility style storage battery. DO

NOT use the unit to charge any 6 Volt batteries. DO NOT

use the unit to crank an engine having a discharged battery.

To recharge 12 Volt batteries, proceed as follows:

1. Check fluid level in all battery cells. If necessary, add

ONLY distilled water to cover separators in battery

cells. DO NOT use tap water.

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• Wear protective goggles, rubber apron, and rubber gloves.

Storage batteries give off explosive hydrogen gas

during recharging.

Hydrogen gas stays near battery for a long time

after battery has been charged.

Slightest spark will ignite hydrogen and cause

explosion.

You can be blinded or severely injured.

Battery electrolyte fluid contains acid and is

extremely caustic.

Contact with battery fluid will cause severe

chemical burns.

DANGER

Figure 7 — Jumper Cable Connections

Grounding

Fastener

• See “Don’t Overload Generator”.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

Exceeding generators wattage/amperage capacity can

damage generator and/or electrical devices connected

to it.

CAUTION

OPERATION

2. If battery is equipped with vent caps, make sure they

are installed and are tight.

3. If necessary, clean battery terminals.

4. Connect battery charge cable connector plug to panel

receptacle identified by the words “12-VOLTS D.C.”

5. Connect battery charge cable clamp with red handle

to positive (+) battery terminal (Figure 8).

6. Connect battery charge cable clamp with black handle

to negative (–) battery terminal (Figure 8).

7. Start engine. Let engine run while battery recharges.

8. When battery has charged, shut down engine

NOTE: Use an automotive hydrometer to test battery

state of charge and condition. Follow the hydrometer

manufacturer’s instructions carefully. Generally, a battery is

considered to be at 100% state of charge when specific

gravity of its fluid (as measured by hydrometer) is 1.260 or

higher.

How to Use the Battery Charger

Use battery float charger jack to keep the starting battery

charged and ready for use. Battery charging should be done

in a dry location, such as inside a garage.

1. Plug charger into unit’s “Battery Float Charger” jack,

which is located on starter switch panel (Figure 9). Plug

battery charger into a 120 Volt AC wall receptacle.

2. Unplug charger from unit and wall outlet when

generator is being started and while in operation.

3. Keep charger plugged in when generator is not in use

to prolong battery life.The charger has a built in float

equalizer and will not overcharge battery, even when

plugged in for an extended period of time.

IMPORTANT: See “Battery Maintenance” on page 16 for

additional information.

COLD WEATHER

OPERATION

Under certain weather conditions (temperatures below

40°F [4°C] combined with high humidity), your generator

may experience icing of the carburetor and/or the

crankcase breather system.To reduce this problem, you

need to perform the following:

1. Make sure generator has clean, fresh fuel.

2. Open fuel valve (turn valve to open position).

3. Use SAE 5W-30 oil (synthetic preferred, see engine

operator’s manual).

4. Check oil level daily or after every eight (8) hours of

operation.

5. Maintain generator following “Maintenance Schedule”

in engine operator’s manual.

6. Shelter unit from elements.

Figure 8 — Battery Connections

Figure 9 — Battery Charger Jack

OPERATION

Creating a Temporary Cold Weather

Shelter

1. In an emergency, use the original shipping carton.

2. Cut off top carton flaps and one long side of carton to

expose muffler side of unit. If required, tape up other

sides of carton to fit over generator as shown in

Figure 10.

3. Cut appropriate slots to access receptacles of unit.

4. Face exposed end away from wind and elements.

5. Locate generator as described in the section

“Generator Location”. Keep exhaust gas from entering

a confined area through windows, doors, ventilation

intakes or other openings.

6. Start generator as described in the section “Starting

the Engine”, then place carton over generator. Keep at

least 5 ft. (152 cm) clearance on all sides of generator

including overhead with shelter in place.

7. Remove shelter when temperatures are above 40°F

[4°C].

8. Turn engine OFF and let cool two (2) minutes before

refueling. Let any spilled fuel evaporate before starting

engine.

Creating a Permanent Cold Weather

Shelter

1. Build a structure that will enclose three sides and the

top of the generator, making sure muffler side of

generator is exposed.

NOTE: Structure should hold enough heat created by the

generator to prevent icing problem.

2. DO NOT enclose generator any more than shown in

Figure 10.

3. Follow steps 3 through 8 as described previously in

“Creating a Temporary Cold Weather Shelter”.

Figure 10 — Permanent Cold Weather Shelter

Wind

• Operate generator ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate generator inside any building or enclosure

(even if doors or windows are open), including the generator

compartment of a recreational vehicle (RV).

Running generator gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide can cause nausea,

fainting or death.

WARNING

• DO NOT touch hot surfaces and avoid hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (152 cm) clearance on all sides of generator

including overhead.

• Remove shelter when temperatures are above 40°F [4°C].

Running engines produce heat.Temperature of

muffler and nearby areas can reach or exceed

150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

WARNING

OPERATION

RECEPTACLES

120/240 Volt AC, 30 Amp, Locking

Receptacle

Use a NEMA L14–30 plug with this receptacle. Connect a

4–wire cord set rated for 250 Volt AC loads at 30 Amps (or

greater) (Figure 11).You can use the same 4–wire cord if

you plan to run a 120 Volt load.

This receptacle powers 120/240 Volt AC, 60 Hz, single

phase loads requiring up to 3,500 watts of power at

29.1 Amps for 120 Volts; 7,000 watts of power (7.0 kW) at

29.1 Amps for 240 Volts.The outlet is protected by a

30 Amp rocker switch circuit breaker.

120 Volt AC, 20 Amp, Duplex

Receptacle

Each receptacle (Figure 12) is protected against overload by

a 20 Amp push–to–reset circuit breaker.

Use each receptacle to operate 120 Volt AC, single–phase,

60 Hz electrical loads requiring up to 2,400 watts (2.4 kW)

at 20 Amps of current. Use cord sets that are rated for

125 Volt AC loads at 20 Amps (or greater).

12 Volt DC, 10 Amp Receptacle

This receptacle allows you to recharge a 12 Volt

automotive or utility style storage battery with the battery

charge cables provided (Figure 13).

This receptacle can not recharge 6 Volt batteries and can

not be used to crank an engine having a discharged battery.

See the section “Charging a Battery” (page 10) before

attempting to recharge a battery.

Figure 11 — 120/240 Volt AC, 30 Amp Receptacle

4-Wire Cord Set

240V

120V

W (Neutral)

X (Hot)

Y (Hot)

NEMA L14-30

Ground (Green)

Figure 12 — 120 Volt AC, 20 Amp, Duplex Receptacle

Figure 13 — 12 Volt DC, 10 Amp Receptacle

• NEVER attempt to power a device requiring more amperage

than generator or receptacle can supply.

• DO NOT overload the generator. See “Don’t Overload

Generator”.

Receptacles may be marked with rating value greater

than generator output capacity.

CAUTION

OPERATION

DON’T OVERLOAD

GENERATOR

Capacity

You must make sure your generator can supply enough

rated (running) and surge (starting) watts for the items you

will power at the same time. Follow these simple steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items.This is

the amount of power your generator must produce to

keep your items running. See Figure 14.

3. Estimate how many surge (starting) watts you will

need. Surge wattage is the short burst of power

needed to start electric motor-driven tools or

appliances such as a circular saw or refrigerator.

Because not all motors start at the same time, total

surge watts can be estimated by adding only the

item(s) with the highest additional surge watts to the

total rated watts from step 2.

Example:

Total Rated (Running) Watts = 3075

Highest Additional Surge Watts = 1800

Total Generator Output Required = 4875

Power Management

To prolong the life of your generator and attached devices,

it is important to take care when adding electrical loads to

your generator.There should be nothing connected to the

generator outlets before starting its engine.The correct

and safe way to manage generator power is to sequentially

add loads as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly.

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

NEVER add more loads than the generator capacity.Take

special care to consider surge loads in generator capacity,

as described above.

*Wattages listed are approximate only. Check tool or

appliance for actual wattage.

Tool or Appliance

Rated (Running)

Watts

Additional Surge

(Starting) Watts

Window Air

Conditioner

1200 1800

Refrigerator 800 1600

Deep Freezer 500 500

Television 500 -

Light (75 Watts) 75 -

3075 Total

Running Watts

1800 Highest

Surge Watts

Tool or Appliance

Rated*

(Running)

Watts

Additional

Surge

(Starting)

Watts

Essentials

Light Bulb - 75 watt

Deep Freezer

500

Sump Pump

800

1200

Refrigerator/Freezer - 18 Cu. Ft.

800

1600

Water Well Pump - 1/3 HP

1000

2000

Heating/Cooling

Window AC - 10,000 BTU

1200

1800

Window Fan

300

600

Furnace Fan Blower - 1/2 HP

800

1300

Kitchen

Microwave Oven - 1000 Watt

1000

Coffee Maker

1500

Electric Stove - Single Element

1500

Hot Plate

2500

Family Room

DVD/CD Player

100

VCR

100

Stereo Receiver

450

Color Television - 27”

500

Personal Computer w/17” monitor

800

Other

Security System

180

AM/FM Clock Radio

300

Garage Door Opener - 1/2 HP

480

520

Electric Water Heater - 40 Gallon

4000

DIY/Job Site

Quartz Halogen Work Light

1000

Airless Sprayer - 1/3 HP

600

1200

Reciprocating Saw

960

Electric Drill - 1/2 HP

1000

Circular Saw - 7 1/4”

1500

Miter Saw - 10”

1800

Table Planer - 6”

1800

Table Saw/Radial Arm Saw - 10”

2000

Air Compressor - 1-1/2 HP

2500

Figure 14 - Wattage Reference Chart

SPECIFICATIONS & MAINTENANCE

SPECIFICATIONS

Starting Wattage . . . . . . . . . . . . . . . . . . . . 12,250 Watts

Wattage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7,000 Watts

AC Load Current

At 120 Volts . . . . . . . . . . . . . . . . . . . . . . . 58.3 Amps

At 240 Volts . . . . . . . . . . . . . . . . . . . . . . . 29.1 Amps

Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-phase

Rated Frequency . . . . . . . . . . . . . . . . . . . . . . . 60 Hertz

Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . 7 U.S. gallons

Shipping Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 230 lbs.

GENERAL MAINTENANCE

RECOMMENDATIONS

The Owner/Operator is responsible for making sure that

all periodic maintenance tasks are completed on a timely

basis; that all discrepancies are corrected; and that the unit

is kept clean and properly stored. NEVER operate a

damaged or defective generator.

NOTE: If equipped with inflatable tires, keep the air pressure

at the value marked on the tire or within 15 and 40 psi.

NOTE: Should you have questions about replacing

components on your BSPP generator, please call

1-800-743-4115 for assistance.

Engine Maintenance

See engine operator’s manual for instructions.

An oil drain tray is provided for your convenience to

change the oil and oil filter. Store tray in a convenient

location for periodic maintenance.

Changing Oil

1. Place the half moon notch in the oil drain tray under

the oil drain plug (Figure 15).

2. Place the oil drain tray foot tab in the slot on the base

of the generator, as shown.

3. Follow the instructions given in the engine operator’s

manual for draining oil.

4. After oil has drained, reinstall the oil drain plug.

5. Remove the oil drain tray from under the oil drain plug

and clean up any spilled oil.

Changing Oil Filter

1. Place the half moon notch in the oil drain tray under

the oil filter (Figure 16).

2. Place the oil drain tray foot tab in the slot on the base

of the generator, as shown.

3. Follow the instructions given in the engine operator’s

manual for changing oil filter and adding oil.

4. Remove the oil drain tray from under the oil filter and

clean up any spilled oil.

KEEP OUT OF REACH OF CHILDREN. DON'T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

• Used motor oil has been shown to cause skin cancer in

certain laboratory animals.

• Thoroughly wash exposed areas with soap and water.

Avoid prolonged or repeated skin contact with used

motor oil.

CAUTION

Figure 15 — Changing Oil With Oil Drain Tray

drain tray foot

drain tray notch

Figure 16 — Changing Oil Filter With Oil Drain Tray

drain tray

notch

drain tray foot

MAINTENANCE & STORAGE

Generator Maintenance

Generator maintenance consists of keeping the unit clean

and dry. Operate and store the unit in a clean dry

environment where it will not be exposed to excessive

dust, dirt, moisture or any corrosive vapors. Cooling air

slots in the generator must not become clogged with snow,

leaves or any other foreign material.

NOTE: DO NOT use a garden hose to clean generator.

Water can enter engine fuel system and cause problems. In

addition, if water enters generator through cooling air slots,

some of the water will be retained in voids and cracks of

the rotor and stator winding insulation.Water and dirt

buildup on the generator internal windings will eventually

decrease the insulation resistance of these windings.

Battery Maintenance

Other than float charging, as described in “How to Use the

Battery Charger”, no maintenance is required for the

battery. Keep the battery and terminals clean and dry.

IMPORTANT: Battery charging should be performed in a

dry location, such as inside a garage.

Generator Cleaning

• Use a damp cloth to wipe exterior surfaces clean.

• Use a soft bristle brush to loosen caked on dirt or oil.

• Use a vacuum cleaner to pick up loose dirt and debris.

• Inspect cooling air slots and opening on generator.These

openings must be kept clean and unobstructed.

STORAGE

The generator should be started at least once every seven

days and allowed to run at least 30 minutes. If this cannot

be done and you must store the unit for more than

30 days, use the following guidelines to prepare it for

storage.

Generator Storage

• Clean the generator as outlined in “Generator Cleaning”.

• Check that cooling air slots and openings on generator

are open and unobstructed.

Engine Storage

See engine operator’s manual for instructions.

Other Storage Tips

• To prevent gum from forming in fuel system or on

essential carburetor parts, add fuel stabilizer into fuel

tank and fill with fresh fuel. Run the unit for several

minutes to circulate the additive through the carburetor.

The unit and fuel can then be stored for up to

24 months. Fuel stabilizer can be purchased locally.

• DO NOT store fuel from one season to another unless

it has been treated as described above.

• Replace fuel container if it starts to rust. Rust and/or dirt

in fuel can cause problems if it's used with this unit.

• Store unit in a clean and dry area.

• DO NOT expose generator to excessive moisture, dust, dirt,

or corrosive vapors.

• DO NOT insert any objects through cooling slots.

Improper treatment of generator can damage it and

shorten its life.

CAUTION

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Unintentional sparking can result in fire or

electric shock.

WARNING

• DO NOT place a storage cover over a hot generator.

• Let equipment cool for a sufficient time before placing the

cover on the equipment.

Storage covers can be flammable.

WARNING

TROUBLESHOOTING

Problem Cause Correction

No AC output is available, but

generator is running.

1. One of the circuit breakers is

open.

2. Fault in generator.

3. Poor connection or defective cord

set.

4. Connected device is bad.

1. Reset circuit breaker.

2. Contact Authorized service facility.

3. Check and repair.

4. Connect another device that is in

good condition.

Generator runs good at no-load

but "bogs" down" when loads are

connected.

1. Short circuit in a connected load.

2. Generator is overloaded.

3. Shorted generator circuit.

1. Disconnect shorted electrical load.

2. See "Don't Overload Generator".

3. Contact Authorized service facility.

Generator will not start; or starts

and runs rough.

1. 10 Amp in-line fuse is blown.

2. Discharged battery.

3. Failed battery.

4. Low oil level.

1. Replace fuse.

2. Jump start generator and/or charge

battery.

3. Replace battery.

4. Fill crankcase to proper level or

place generator on level surface.

Generator shuts down during

operation.

Out of gasoline. Fill fuel tank.

Generator lacks power. Load is too high. See "Don't Overload Generator".

NOTES

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC PORTABLE GENERATOR OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the portable generator that is

defective in material or workmanship or both. Transportation charges on product submitted for repair or replacement under this

warranty must be borne by purchaser. This warranty is effective for the time periods and subject to the conditions stated below.

For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at www.briggspowerproducts.com.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT

PERMITTED BY LAW ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some states or

countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the

exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This

warranty gives you specific legal rights and you may also have other rights which vary from state to state or country to country.

2 years*

1 year

Consumer Use

Commercial Use

The warranty period begins on the date of purchase by the first retail end user, and continues for the period of time stated above.

“Consumer Use" means personal residential household use by a retail consumer. “Commercial Use" means all other uses, including

use for commercial, income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter be

considered as commercial use for purposes of this warranty.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE

YOUR PROOF OF PURCHASE RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME

WARRANTY SERVICE IS REQUESTED, THE MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE

THE WARRANTY PERIOD.

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty

repairs. Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For

example, warranty service would not apply if equipment damage occurred because of misuse, lack of routine maintenance,

shipping, handling, warehousing or improper installation. Similarly, the warranty is void if the manufacturing date or the serial number

on the portable generator has been removed or the equipment has been altered or modified. During the warranty period, the

Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under normal

use and service. This warranty will not cover the following repairs and equipment:

• Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This

warranty does not cover repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or

unauthorized installation or alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper

maintenance, repair or storage so as, in our judgment, to adversely affect its performance and reliability. This warranty also does

not cover normal maintenance such as air filters, adjustments, fuel system cleaning and obstruction (due to chemical, dirt,

carbon, lime, and so forth).

• Other Exclusions: This warranty excludes wear items such as o-rings, filters, etc., or malfunctions resulting from accidents,

abuse, modifications, alterations, or improper servicing or freezing or chemical deterioration. Accessory parts such as generator

adapter cord sets and storage covers are excluded from the product warranty. This warranty excludes used, reconditioned, and

demonstration equipment, equipment used for prime power in place of utility power, equipment used in life support applications,

and failures due to acts of God and other force majeure events beyond the manufacturers control.

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WI, USA

Effective February 1, 2006 replaces all undated Warranties and all Warranties dated before February 1, 2006

198189E, Rev 0. 02/01/2006

*Second year parts only

WARRANTY PERIOD

RÈGLES DE SÉCURITÉ

TABLE DES MATIÈRES

Règles de Sécurité. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-22

Connaissez Votre Générateur . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Assemblage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25

Opération . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-32

Entretien . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-34

Rangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Remarques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Dépannage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

DESCRIPTION DE L ÉQUIPEMENT

Lisez avec soin ce manuel et familiarisez-vous avec

votre générateur. Connaissez ses applications, ses

limitations et les dangers qu'il implique.

Ce générateur est un générateur entraîné par un moteur à champ

magnétique rotatif produisant du courant alternatif (c.a.). Il a été

conçu pour fournir du courant électrique pour faire marcher des

charges compatibles d'éclairage, d'appareils ménagers, d'outil et de

moteur. Le champ tournant du générateur est entraîné à

3,600 T/M par un moteur seul cylindrique.

ATTENTION! NE PAS dépasser la capacité en watts ou en

Ampères du générateur.Voir "Ne Pas Surcharger Générateur"

pour l'information spécifique.

Tout a été mis en oeuvre pour que les informations contenues

dans ce manuel soient exactes et à jour. Cependant, nous se

réserve le droit de changer, d'altérer ou d'améliorer le produit à

n'importe quel moment sans avis préalable.

Le Système de contrôle de l'émission du générateur est garanti

pour des normes établies par L'Agence de protection de

l'environnement et le California Air Resources Board. Pour des

informations sur la garantie, se reporter au manuel d'utilisation du

moteur.

RÈGLES DE SÉCURITÉ

Ceci est la sûreté le symbole vif. Il est utilisé pour

vous alerter aux dangers de blessure personnels

potentiels. Obéir tous messages de sûreté qui suivent

ce symbole éviter la blessure ou la mort possibles.

Le symbole indiquant un message de sécurité est accompagné d'un

mot indicateur (DANGER,ATTENTION,AVERTISSEMENT), d'un

message illustré et/ou d'un message de sécurité visant à vous

avertir des dangers. DANGER indique un danger qui, s'il n'est pas

évité, provoquera des blessures graves, voire fatales.

AVERTISSEMENT indique un danger qui, s'il n'est pas évité, peut

provoquer des blessures graves, voire fatales. ATTENTION

indique un danger qui, s'il n'est pas évité, peut provoquer des

blessures mineures ou légères. Le mot ATTENTION, lorsqu'il est

utilisé sans le symbole d'alerte, indique une situation pouvant

endommager l'équipement. Suivez les messages de sécurité pour

éviter ou réduire les risques de blessures ou de mort.

Symboles de Danger et Moyens

L’échappement du moteur de ce produit contient des produits

chimiques que l’État de Californie considère comme causant le

cancer, des déformations à la naissance ou d’autres dangers

concernant la reproduction.

AVERTISSEMENT

Feu

Explosion

Emanations Toxiques

Surface Chaude

Manuel d'Utilisation

Choc Électrique

Pression Explosive

Brûlures Chimiques

VEUILLEZ CONSERVER CES INSTRUCTIONS

La page charge ...

Briggs & Stratton ELITE 7000 WATT Manuel utilisateur

Marque: Briggs & Stratton

Modèle: ELITE 7000 WATT

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Briggs & Stratton ELITE 7000 WATT User manual
español: Briggs & Stratton ELITE 7000 WATT Manual de usuario

Briggs & Stratton ELITE 7000 WATT Manuel utilisateur

Ce manuel convient également à

Briggs & Stratton ELITE 7000 WATT Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents