Simplicity 071019 Manuel utilisateur

Marque: Simplicity

Modèle: 071019

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Home Generator Systems

Installation & Operator’s Manual

Manual No. 201705GS Rev. B (04/14/08)

100/200 Amp

Automatic Transfer Switch

2 BRIGGSandSTRATTON.COM

Briggs & Stratton Power Products Group, LLC

900 North Parkway

Jefferson, WI 53549

reproduced or transmitted in any form by any means without

the express written permission of Briggs & Stratton Power

Products Group, LLC.

Thank you for your purchase of this Briggs & Stratton Power Products Automatic Transfer Switch. This product is intended

for use with Briggs & Stratton Home Standby Generator sets and therefore may not function with generators produced by

other manufacturers. Seek a qualified electrical professional to determine applicability of this equipment to generators aside

from those manufactured by Briggs & Stratton. This is an optional home standby system which provides an alternate source

of electric power and to serve loads such as a gas furnace, refrigeration and communication systems that, when stopped

during any power outage, could cause discomfort, or the like. This product DOES NOT qualify for emergency standby as

defined by NFPA 70 (NEC).

This manual contains safety information to make you aware of the hazards and risks associated with transfer switches and

how to avoid them. Briggs & Stratton has made every effort to provide for a safe, streamlined and cost-effective installation.

Each installation is unique, it is impossible to know of and advise of all conceivable procedures and methods by which

installation might be achieved. We do not know all possible hazards and/or the results of each method or procedure. Save

these instructions for future reference.

This transfer switch requires installation before use. Refer to the Installation section of this manual for instructions on

installation procedures. Only licensed electrical contractors should install transfer switches. Installations must strictly

comply with all applicable federal, state and local codes, standards and regulations.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your transfer switch. Consult your Yellow Pages.

There are many Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also contact

Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet at BRIGGSandSTRATTON.COM.

Transfer Switch

Model Number

Revision

Serial Number

Date Purchased

3
FrançaisEspañol
Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
For the Home Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Owner Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installer Responsibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Equipment Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Mounting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
System Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Supervisory Control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Wiring Interconnections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Testing the Automatic Transfer Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Schematic and Wiring Diagram, Models 071018 and 071019. . . . . . . . . . 13
Schematic and Wiring Diagram, Models 071020 and 071021. . . . . . . . . . 14
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table of Contents

4 BRIGGSandSTRATTON.COM

Safety Rules

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all

safety messages that follow this symbol to avoid

possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION, WARNING), a pictorial and/or a safety

message to alert you to hazards. DANGER indicates a hazard

which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury. CAUTION indicates a hazard

which, if not avoided, might result in minor or moderate

injury. NOTICE indicates a situation that could result in

equipment damage. Follow safety messages to avoid or

reduce the risk of injury or death.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that it

is safe for you and others. You must also make sure that the

procedure, work method or operating technique that you

choose does not render the transfer switch unsafe.

WARNING

Only qualified electricians should attempt installation of

this system, which must strictly comply with applicable

codes, standards and regulations.

WARNING

Failure to properly ground transfer switch can

result in electrocution.

• DO NOT touch bare wires or receptacles.

• DO NOT use transfer switch with worn, frayed, bare or

otherwise damaged wiring.

• DO NOT handle electrical cords while standing in water, while

barefoot, or while hands or feet are wet.

• If you must work around a unit while it is operating, stand on an

insulated dry surface to reduce shock hazard.

• DO NOT allow unqualified persons or children to operate or

service transfer switch.

• In case of an accident caused by electrical shock, immediately

shut down the source of electrical power and contact local

authorities. Avoid direct contact with the victim.

WARNING

Low voltage wire cannot be installed in same

conduit as power voltage wiring.

• Failure to follow above warning could cause personal injury,

damage and/or malfunction of equipment.

WARNING

Transfer Switch contains hazardous voltage that

can cause personal injury or death.

• Despite the safe design of the transfer switch, operating this

equipment imprudently, neglecting its maintenance or being

careless can cause possible injury or death.

NOTICE

Improper treatment of transfer switch can damage it and

shorten its life.

• Use transfer switch only for intended uses.

• If you have questions about intended use, ask dealer or contact

Briggs and Stratton Power Products.

• DO NOT expose transfer switch to excessive moisture, dust,

dirt, or corrosive vapors.

• Remain alert at all times while working on this equipment.

NEVER work on the equipment when you are physically or

mentally fatigued.

• If connected devices overheat, turn them off and turn off their

circuit breaker/fuse.

WARNING

Certain components in this product and related

accessories contain chemicals known to the State of

California to cause cancer, birth defects, or other

reproductive harm. Wash hands after handling.

Introduction

Your Briggs & Stratton Transfer Switch is supplied with this

combined “Installation and Operator’s Manual”. This is an

important document and should be retained by the owner

after the installation has been completed.

Every effort has been expended to make sure that the

information in this manual is both accurate and current.

However, the manufacturer reserves the right to change, alter

or otherwise improve the system at any time without prior

notice.

For the Home Owner

To help you make informed choices and communicate

effectively with your installation contractor(s),

Read and understand the Owner Orientation Section

of this manual BEFORE contracting or starting your

transfer switch installation.

To arrange for proper installation, contact the store at which

you purchased your Briggs & Stratton Transfer Switch, your

dealer, or your utility power provider.

The Transfer Switch Warranty is VOID

unless the system is installed by a

licensed electrical professional.

Owner Orientation

The illustrations are for typical circumstances and are meant

to familiarize you with the installation options available with

your transfer switch.

Local codes, appearance, and distances are the factors that

must be considered when negotiating with an installation

professional. As the distance from the existing electrical

service increases, compensation in wiring materials must be

allowed for. This is necessary to comply with local codes and

overcome electrical voltage drops.

The factors mentioned above will have a direct effect on the

overall price of your transfer switch installation.

NOTE: Your installer must check local codes AND obtain

permits before installing the system.

• Read and follow the instructions given in this manual.

• Follow a regular schedule in caring for and using your

transfer switch, as specified in the manual.

Installer Responsibilities

• Read and observe the safety rules.

• Read and follow the instructions given in this manual.

• Check federal, state and local codes and authority

having jurisdiction, for questions on installation.

• Ensure generator is not overloaded with selected loads.

If you need more information about the transfer switch, call

(800) 743-4115, between 8:00 AM and 5:00 PM CT.

Equipment Description

These transfer switches are intended to transfer the entire

electrical load of normal residential installations when used

with the supervisory contacts provided. The load is

connected either to utility power (normal) or home standby

power (generator). The transfer switch monitors utility and

generator voltages and will automatically connect to the

appropriate source of power.

Major components of the transfer switch are a 2 pole utility

disconnect circuit breaker (models 071020 & 071021 only),

a 2 pole double throw transfer switch, control circuit board,

fused utility terminals and interconnecting wiring. The

control board also has two inputs for current tranformers

used to sense generator current.

The transfer switch is solenoid-operated from utility or

generator inputs and contains suitable mechanical and

electrical interlock switches to eliminate the possibility of

connecting the utility service to the generator output. It has

ratings capable of switching full utility power into the

residence. In addition, a manual override lever is provided

for the transfer function.

The control circuit board has active circuits sensing utility

and generator voltages. It creates a signal for the generator

start-up, switch transfer, and retransfer when utility is

restored. The control board also contains red and green

LED’s indicating the power sources available and two relay

operated contacts that provide supervisory control of

external loads.

6 BRIGGSandSTRATTON.COM

Installation

Unpacking

Delivery Inspection

After removing the carton, carefully inspect the transfer

switch components for any damage that may have occurred

during shipment.

IMPORTANT: If loss or damage is noted at time of delivery,

have the person(s) making delivery note all damage on the

freight bill and affix his signature under the consignor's

memo of loss or damage. If loss or damage is noted after

delivery, contact the carrier for claim procedures. Missing or

damaged parts are not warranted.

Shipment Contents

• Automatic Power Transfer Switch

• Installation and Operator’s Manual

• Current Transformers

Mounting Guidelines

The Automatic Transfer Switch is enclosed in a NEMA

Type 3R enclosure suitable for indoor/outdoor use.

Guidelines for mounting the Automatic Transfer Switch

include:

• Install the switch on a firm, sturdy supporting structure.

• The switch must be installed with minimum NEMA 3R

hardware for conduit connections.

• To prevent switch contact distortion, level and plumb the

enclosure. This can be done by placing washers between

the switch enclosure and the mounting surface.

• NEVER install the switch where any corrosive

substance might drip onto the enclosure.

• Protect the switch at all times against excessive moisture,

dust, dirt, lint, construction grit and corrosive vapors.

A typical installation of the Automatic Power Transfer Switch

is depicted below. An alternative installation of the Automatic

Power Transfer Switch is also depicted below. It is best if the

transfer switch is mounted near the utility meter, either

inside or outside. Discuss layout suggestions/ changes with

the owner before beginning the system installation process.

Main

Breaker

Panel

Transfer

Switch

Hot Water

Heater

Air

Conditioner

Contactor

Generator

Watt -

Hourmeter

Typical

Branch Circuits

— — — — — — Control Wiring

Disconnect Switch

Main

Breaker

Panel

Transfer

Switch

Hot Water

Heater

Air

Conditioner

Contactor

Disconnect Switch

Generator

Watt -

Hourmeter

Branch

Circuits

Emergency

Branch Circuits

— — — — — — Control Wiring

Emergency

Load Center

Alternate

Service

Disconnect

System Setup

You must perform the following on the control module

before operating the system:

• If generator is installed in an area regularly subjected to

temperatures below 40°F (4°C), select a 50 second

warm up time by moving jumper installed on JP2 from

‘20’ position to ‘50’ position.

• Place 2 position switch in ‘NG’ or ‘LP’ position,

whichever is appropriate for your system.

• Place 3 position switch to match KW rating of installed

generator.

Supervisory Control Wiring

1. Terminal strip on control module in transfer switch has

four connections for customer use. There are two sets

of “Normally Closed” contacts available. They will be

activated when generator power is required. These can

be used for supervisory control of large connected

loads on generator. Loads will be allowed to operate if

there is enough generator power available.

NOTE: There are two wireways provided to keep the

supervisory loads separated from each other.

2. Terminals “A-A” on control module are rated for 24 VAC

and air conditioner contactor control. Contacts are

connected in series with the air conditioner contactor

control circuit.

3. Terminals “B-B” on control module are rated for 1 Amp

125 VAC and installer supplied contactor to control a

large load. Example: electric hot water heater. Contacts

are connected in series with the contactor control

circuit.

4. Tighten all wire connections/fasteners to proper torque.

See inside transfer switch enclosure for proper torque

values.

Air Conditioner Contactor

24 VAC

Contactor

Neutral

115 VAC

2 Position

Switch

3 Position

Switch

JP2

CT1 & CT2

Connectors

Supervisory

Contacts

8 BRIGGSandSTRATTON.COM

Wiring Interconnections

All wiring must be the proper size, properly supported and

protected by conduit.

Complete the following connections between the transfer

switch, main distribution panel, utility power and generator,

as shown on the next pages.

High Voltage Wiring

1. Ensure utility power is turned OFF. Connect utility

feeder conductors to transfer switch terminals marked

“UTILITY CONNNECTION”.

2. Connect utility Neutral conductor to the transfer switch

“NEUTRAL” terminal.

3. Connect main breaker panel feeder conductors to

transfer switch terminals marked “LOAD

CONNECTION”.

4. Connect main breaker panel Neutral conductor to

transfer switch “NEUTRAL” terminal.

5. Connect main breaker panel Ground conductor to the

transfer switch “GND” terminal.

NOTE: Assure grounding electrode conductor is connected

and bonded per applicable federal, state and local codes,

standards and regulations.

6. Connect generator feeder conductors from the

generator control panel to transfer switch terminals

marked “GENERATOR CONNECTION” Each conductor

should pass through hole of current transformer before

making connection.

7. Plug in current transformer leads into “CT1” and “CT2”

on control module.

8. Connect Neutral conductor from the generator control

panel to the transfer switch “NEUTRAL” terminal.

9. Connect generator Ground conductor from the control

panel to the transfer switch “GND” terminal.

NOTE: Assure generator equipment grounding conductor is

connected per applicable federal, state and local codes,

standards and regulations.

10. Connect generator “UTILITY 240 VAC” terminals to

transfer switch “UTILITY 240 VAC” terminals. Use

minimum #14 AWG conductors.

11. Tighten all wire connections/fasteners to proper torque.

See inside transfer switch enclosure for proper torque

values.

Low Voltage Wiring

1. Using #18 AWG twisted pair conductors, no greater

than 200 ft in length, connect Tx Rx and Tx Rx Ground

from the generator control panel to the GND and T/R on

the transfer switch control board.

2. Tighten all wire connections/fasteners to proper torque.

See inside transfer switch enclosure for proper torque

values.

WARNING

Low voltage wire cannot be installed in same

conduit as power voltage wiring.

• Failure to follow above warning could cause personal injury,

damage and/or malfunction of equipment.

Main

Main Distribution Panel

Ground Bus

Neutral

Bus

To Generator

Neutral

Terminal

To Utility Meter

Supervisory

Contacts

Load

Connection

Ground

Terminal

Generator

Connection

Utility

Connection

Wireways

CT 1

CT 2

240V Generator

Connection

Generator Tx Rx and

Tx Rx Ground Connection

For Models 071018 & 071019

10 BRIGGSandSTRATTON.COM

Main

Main Distribution Panel

Ground Bus

Neutral

Bus

To Generator

Neutral

Terminal

To Utility Meter

Supervisory

Contacts

Load

Connection

Ground

Terminal

Generator

Connection

Utility

Connection

Wireways

CT 1

CT 2

240V Generator

Connection

Generator Tx Rx and

Tx Rx Ground Connection

For Models 071020 & 071021

Controls

Other than a Manual Override lever, there are no operator

controls because this is an automatic transfer switch. The

manual override is to be used only by licensed professionals.

Operation

To select automatic transfer operation, do the following:

1A. For models 071018 & 071019, set disconnect switch

that sends utility power to transfer switch to “On”

position. This switch is probably located in the main

breaker panel.

1B. For models 071020 & 071021, set utility breaker in

transfer switch “On” position.

2. Set generator main circuit breaker to its “On” position.

3. Install 15 Amp fuse in generator control panel.

4A. If generator is equipped with a system AUTO/OFF

switch, set switch to “AUTO” position.

B. If generator is equipped with a AUTO/OFF/MANUAL

switch, set switch to “AUTO” position.

The system will now be in automatic operation mode.

When the generator is providing power to the transfer

switch, the controller is constantly monitoring generator

power. If the air conditioner is called to run, and there is

sufficient generator power available, the controller will close

contacts “A-A” to air conditioner contactor. Contacts “B-B”

will open before contacts A-A close. If loads are too great for

generator, contacts A-A and/or B-B will open. When air

conditioning is not needed, A-A will open. If enough power is

available, B-B will close.

Testing the Automatic Transfer Switch

Turn the service disconnect feeding the transfer switch

contactor to the “Off” position. The automatic sequence of

the system will follow. To go back to utility power, turn the

service disconnect to the “On” position.

Utility Fail

The Home Standby Generator set senses when utility voltage

is below 70 percent of nominal. Engine start sequence is

initiated after 6 second time delay.

Engine Warm-Up

Time delay to allow for engine warm-up before transfer is

fixed at 20 seconds or 50 seconds with removal of jumper

on control board.

Transfer

Transfer from utility to generator supply occurs after voltage

is above set levels. Minimum engine run time is 5 minutes

after transfer.

Utility Pickup

Voltage pickup level is 80 percent of nominal voltage.

Retransfer

Retransfer from generator to utility supply is approximately

10 seconds after utility voltage supply is above pickup level

and minimum run time is completed.

Engine Cool Down

Engine will run for 60 seconds after retransfer.

Maintenance

The transfer switch is designed to be maintenance free under

normal usage. However, inspection and maintenance checks

should be made on a regular basis. Maintenance will consist

mainly of keeping the transfer switch clean.

Visual inspections should be done at least once a month.

Access to transfer switch must not be obstructed. Keep

3 feet (92 cm) clearance around transfer switch. Check for

an accumulation of dirt, moisture and/or corrosion on and

around the enclosure, loose parts/hardware, cracks and/or

discoloration to insulation, and damaged or discolored

components.

Exercise the transfer switch at least once every three months

as described in the previous section Testing the Automatic

Transfer Switch unless a power outage occurs and Home

Generator System has gone through automatic sequence.

Allow generator to run for at least 30 minutes.

Contact a licensed electrical professional to inspect and clean

the inside of your transfer switch at least once a year.

12 BRIGGSandSTRATTON.COM

Troubleshooting

Problem Cause Correction

Automatic transfer switch does not

transfer to generator

1. Generator breaker open.

2. Generator voltage not acceptable.

1. Reset generator circuit breaker.

2. Refer to generator manual.

Automatic transfer switch does not

transfer to utility

1. Utility disconnect breaker open

(Models 071020 & 071021 only).

2. Service disconnect breaker open.

3. Utility voltage not acceptable.

1. Reset utility disconnect breaker

(Models 071020 & 071021 only).

2. Reset service disconnect breaker.

3. Wait for utility voltage to return to

normal.

Generator is still running after switch

transfers to utility power

Engine cool down period. Engine should stop after 1 minute.

Supervised loads (air conditioner, etc.)

are not operating when generator is

supplying power

1. A-A or B-B contacts not operating

correctly.

2. Too much load on generator.

3. Current transformer not connected.

4. Broken current transformer.

1. Check A-A or B-B contacts for

proper operation and/or check

control wiring to external load.

2. Decrease load to generator.

3. Plug CT connectors into control

board.

4. Contact local Briggs & Stratton

Power Products service center.

Generator is still running after utility

power is restored

1. Minimum engine run time has not

elapsed.

2. Fuse(s) in transfer switch is

defective.

1. Wait five minutes for transfer

switch to retransfer to utility power.

2. Check fuse(s) and replace if

necessary.

Schematic and Wiring Diagram, Models 071018 and 071019

14 BRIGGSandSTRATTON.COM

Schematic and Wiring Diagram, Models 071020 and 071021

1515

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC TRANSFER SWITCH OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the equipment that is defective in material or

workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This

warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in

our dealer locator map at BRIGGSandSTRATTON.COM.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW. ANY AND ALL IMPLIED WARRANTIES ARE

EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some

states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and

you may also have other rights which vary from state to state or country to country.

3 years

None

Consumer Use

Commercial Use

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the

table above. “Consumer use" means personal residential household use by a retail consumer. “Commercial use" means all other uses, including use for

commercial, income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter be considered as commercial use for

purposes of this warranty. Equipment used for prime power in place of utility are not applicable to this warranty.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE

RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE MANUFACTURING

DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most warranty

repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not apply if

equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation. Similarly, the

warranty is void if the manufacturing date or the serial number on the equipment has been removed or the equipment has been altered or modified. During

the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under normal

use and service. This warranty will not cover the following repairs and equipment:

• Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty does not cover

repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized installation or

alteration and modification, misuse, negligence, accident, overloading, improper maintenance, repair or storage so as, in our judgment, to adversely

affect its performance and reliability. This warranty also does not cover normal maintenance such as adjustments, cleaning and fuse replacement.

• Other Exclusions: This warranty excludes wear items or damage or malfunctions resulting from accidents, abuse, modifications, alterations, or

improper servicing. Accessory parts are excluded from the product warranty. This warranty excludes failures due to acts of God and other force

majeure events beyond the manufacturers control. Also excluded is used, reconditioned, and demonstration equipment.

198180E, Rev. C, 12/31/2006

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WI, USA

Effective November 1, 2005 replaces all undated Warranties and all Warranties dated before November 1, 2005

WARRANTY PERIOD

16 BRIGGSandSTRATTON.COM

Product Specifications

Model 071018

Maximum Load Current . . . . . . . . . . . . . . . . . . . . .100 Amps

Rated AC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . .250 Volts

Poles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Hz

Fault Current Rating . . . .22,000 RMS Symmetrical Amperes

Supervisory Contacts Rating:

A-A Terminals . . . . . . . . . . . . . . . . . . . . . . . . . .24 Volt AC

B-B Terminals . . . . . . . . . .1 Amp, 125 Volt AC, Pilot Duty

Model 071019

Maximum Load Current . . . . . . . . . . . . . . . . . . . . .200 Amps

Rated AC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . .250 Volts

Poles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Hz

Fault Current Rating . . . .25,000 RMS Symmetrical Amperes

Supervisory Contacts Rating:

A-A Terminals . . . . . . . . . . . . . . . . . . . . . . . . . .24 Volt AC

B-B Terminals . . . . . . . . . .1 Amp, 125 Volt AC, Pilot Duty

Model 071020

Maximum Load Current . . . . . . . . . . . . . . . . . . . . .100 Amps

Rated AC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . .250 Volts

Poles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Hz

Fault Current Rating . . . .22,000 RMS Symmetrical Amperes

Supervisory Contacts Rating:

A-A Terminals . . . . . . . . . . . . . . . . . . . . . . . . . .24 Volt AC

B-B Terminals . . . . . . . . . .1 Amp, 125 Volt AC, Pilot Duty

Model 071021

Maximum Load Current . . . . . . . . . . . . . . . . . . . . .200 Amps

Rated AC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . .250 Volts

Poles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Hz

Fault Current Rating . . . .25,000 RMS Symmetrical Amperes

Supervisory Contacts Rating:

A-A Terminals . . . . . . . . . . . . . . . . . . . . . . . . . .24 Volt AC

B-B Terminals . . . . . . . . . .1 Amp, 125 Volt AC, Pilot Duty

Briggs & Stratton Power Products Group, LLC

900 N. Parkway

Jefferson, Wisconsin, 53549 U.S.A.

Transfer Switch

This transfer switch is certified in accordance with UL (Underwriters Laboratories) 1008 (transfer switch equipment).

(800) 743-4115

Home Generator Systems

Manual de Instalación y del Operario

100/200 Amp

Automatic Transfer Switch

2 BRIGGSandSTRATTON.COM

Gracias por comprar este conectador automático Briggs & Stratton Power Products. Este producto está pensado para

funcionar con generadores de reserva domésticos Briggs & Stratton, por lo que es posible que no pueda utilizarse con

generadores de otros fabricantes. Consulte con un electricista cualificado para determinar si este equipo es adecuado para

funcionar con generadores no fabricados por Briggs & Stratton. Este producto es un sistema doméstico de reserva opcional y

proporciona una fuente alternativa de energía eléctrica con capacidad para alimentar cargas tales como calderas de gas y

sistemas de refrigeración y de telecomunicaciones, que cuando dejan de funcionar a causa de una interrupción de la

alimentación eléctrica de la red pueden producir incomodidades o problemas. Este producto no pertenece a la categoría de

reserva de emergencia según lo definido por la norma NFPA 70 (NEC).

Este manual contiene información de seguridad sobre los riesgos asociados con los conectadores y sobre cómo evitarlos.

Briggs & Stratton ha realizado el máximo esfuerzo para que la instalación resulte segura, sencilla y económica. Cada

instalación es única, lo que hace imposible conocer y recomendar todos los procedimientos y métodos posibles para

efectuarla. No conocemos todos los riesgos y/o resultados posibles de cada método o procedimiento. Guarde estas

instrucciones para futuras consultas.

Antes de utilizar el conectador, es necesario instalarlo. Consulte en la sección Instalación de este manual las instrucciones

o procedimientos de instalación. Los conectadores sólo deben ser instalados por electricistas cualificados. Las

instalaciones deben cumplir estrictamente la totalidad de la normativa vigente.

Dónde puede encontrarnos

Nunca tendrá que buscar mucho para poder obtener soporte y servicio técnico para su conectador Briggs & Stratton. Consulte

las páginas amarillas. Hay más de 30.000 distribuidores de servicio autorizados en todo el mundo que le ofrecerán un servicio

de calidad. También puede dirigirse al departamento de servicio al cliente de Briggs & Stratton llamando al (800) 743-4115 o

por Internet, en el sitio web BRIGGSandSTRATTON.COM.

Conectador Automático

Número de Modelo

Revisión

Número de Serie

Fecha de compra

Briggs & Stratton Power Products Group, LLC.

900 North Parkway

Jefferson, WI 53549

Reservados todos los derechos. Queda prohibida la reproducción o

transmisión total o parcial de este material, sea cual sea la forma y

el medio empleados para ello, sin el permiso previo y por escrito

de Briggs & Stratton Power Products Group, LLC.

3
Español
33
Reglas de seguridad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introducción. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Para el Propietario Doméstico . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Orientación para el Propietario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Responsabilidades del Instalador . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Descripción del Equipo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Instalación . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Desempaque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pautas de Montaje . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Configuración del Sistema. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Cableado de Control de Supervisión . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Interconexiones de cableado . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Mandos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Sistema Funcionamiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Prueba del Conectador Automático . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Mantenimiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Reparacion de Averias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Garantía . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Especificaciones del producto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Tabla de Contendio

4 BRIGGSandSTRATTON.COM

Reglas de seguridad

Éste es el símbolo de alerta de seguridad. Sirve

para advertir al usuario de un posible riesgo para

su integridad física. Siga todos los mensajes de

seguridad que figuren después de este símbolo

para evitar lesiones o incluso la muerte.

El símbolo de alerta de seguridad ( ) se utiliza con una

palabra de señalización (PELIGRO, PRECAUCIÓN,

ADVERTENCIA), una imagen y/o un mensaje de seguridad

para advertir al usuario de un riesgo. PELIGRO indica un

riesgo que, de no evitarse, provocará la muerte o lesiones de

gravedad. ADVERTENCIA indica un riesgo que, de no

evitarse, puede provocar la muerte o lesiones de gravedad.

PRECAUCIÓN indica un riesgo que, de no evitarse, puede

provocar lesiones moderadas. Cuando se utiliza sin el

símbolo de alerta, AVISO indica una situación que podría

producir daños en el equipo. Siga en todo momento los

mensajes de seguridad para evitar o reducir el riesgo de

lesiones y de muerte.

El fabricante no puede prever todas las posibles

circunstancias que pueden implicar riesgos. Por lo tanto, las

advertencias que aparecen en este manual y las etiquetas y

calcomanías adheridas a la unidad no incluyen todas las

posibilidades. Si aplica un procedimiento, método de trabajo

o técnica de operación no recomendada específicamente por

el fabricante, debe estar seguro de que se trata de una

práctica segura para usted y para otras personas. También

debe asegurarse de que el procedimiento, método de trabajo

o técnica de operación que elija, no haga que el conmutador

de transferencia se torne inseguro.

ADVERTENCIA

Si no hace tierra apropiadamente con un

conmutador de transferencia, puede hacer que

ocurra un electrocutamiento.

• NO toque los alambres pelados o receptáculos.

• NO use un conmutador de transferencia con cables eléctricos

que estén malgastados, rotos, pelados o dañados de cualquier

forma.

• No maneje el cables eléctricos mientras esté parado en agua,

descalzo o cuando las manos y los pies estén mojados.

• Si fuera necesario realizar trabajos en cercanías de la unidad

mientras está en funcionamiento, párese sobre una superficie

seca y aislada para reducir los riesgos de una descarga.

• NO permita que personas descalificadas o niños operen o sirvan

al conmutador de transferencia.

• En caso de que se produzca un accidente causado por una

descarga eléctrica, cierre inmediatamente la fuente de energía

eléctrica y contacta administración local. Evite el contacto

directo con la víctima.

ADVERTENCIA

Los cables de baja tensión no se pueden instalar

en el mismo conducto que los cables de

suministro de energía.

• Si no se respeta esta indicación pueden producirse lesiones,

daños y/o fallos de funcionamiento del equipo.

ADVERTENCIA

El conectador contiene alta tensión que puede

provocar lesiones o la muerte.

• A pesar del diseño seguro del conmutador de transferencia, si

se opera este equipo en forma imprudente, si no se cumple con

el mantenimiento o si se actúa con descuido, se pueden

producir lesiones o la muerte.

ADVERTENCIA

La instalación de este sistema debe cumplir estrictamente

la totalidad de la normativa vigente, por lo que sólo debe

ser llevada a cabo por un electricista cualificado.

ADVERTENCIA

Determinados componentes en este producto y los

accesorios relacionados contienen sustancias químicas

declaradas cancerígenas, causantes de malformaciones,

y otros defectos congénitos por el Estado de California.

Lávese las manos después de manipular estos elementos.

AVISO

El tratamiento inadecuado del conmutador de

transferencia puede dañarlo y acortar su vida productiva.

• Use el conmutador de transferencia solamente con la finalidad

para el cual fue diseñado.

• Si usted tiene alguna pregunta acerca de las finalidades de uso

del generador, pregúntele a su concesionario o contacte a

Briggs and Stratton Power Products.

• NO exponga al conmutador de transferencia a una humedad

excesiva, polvo, suciedad o vapores corrosivos.

• Permanezca siempre alerta cuando trabaje con este equipo.

NUNCA trabaje con este equipo si se siente cansado física o

mentalmente.

• Si se calientan excesivamente los dispositivos conectados,

apáguelos y abra sus interruptores o quite sus fusibles.

La page charge ...

Simplicity 071019 Manuel utilisateur

Marque: Simplicity

Modèle: 071019

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 071019 User manual
español: Simplicity 071019 Manual de usuario

Simplicity 071019 Manuel utilisateur

Simplicity 071019 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents