GE JGP636CEDCC Guide d'installation

Marque: GE

Modèle: JGP636CEDCC

Catégorie: Cuisinières

Taper: Guide d'installation

Ce manuel convient également à

36″ Sealed Gas Cooktop

Installation

Instructions

CAUTION: Before you begin—read these

instructions completely and carefully.

• IMPORTANT—Save these instructions for

local inspector’s use.

• IMPORTANT—OBSERVE ALL GOVERNING

CODES AND ORDINANCES.

• Note to Installer—Be sure to leave these

instructions with the Consumer.

• Note to Consumer—Keep these instructions

for future reference.

• Note—This appliance must be properly

grounded.

PARTS INCLUDED

1/8" Drill Bit &

Electric or

Hand Drill

Phillips

Head

Screwdriver

Pencil

Ruler or

Straightedge

Joint Sealant

Saber Saw

TOOLS YOU WILL NEED

Pipe Fittings

MATERIALS YOU MAY NEED

JGP636, JGP960

Shut Off

Valves

Pipe Wrench

• IMPORTANT: Leak testing of the appliance

shall be conducted according to the

manufacturer’s instructions.

229C4053P464-1

31-10505-1 (05-03 JR)

In the Commonwealth of Massachusetts:

• This product must be installed by a licensed

plumber or gas fitter.

• When using ball-type gas shut-off valves,

they shall be the T-handle type.

• A flexible gas connector, when used,

must not exceed 3 feet.

2 screws

2 Hold

Down

Brackets

Foam

Tape

Questions? Call GE Answer Center at 800.626.2000 or visit our

Website at: www.geappliances.com

WARNING!!

If the information in this manual

is not followed exactly, a fire, explosion

or gas leak may result, causing property

damage, personal injury or death.

• Installation of this cooktop must conform with

local codes or in the absence of local codes

with the National Fuel Gas Code, ANSI Z223.

1-Latest edition.

• Be sure your cooktop is installed properly by a

qualified installer or service technician.

• To eliminate reaching over surface burners,

cabinet storage above burner should be avoided.

• Do not install the unit near an outside door or

where a draft may affect its use.

Do not store or use gasoline or other

flammable vapors and liquids in the vicinity

of this or any other appliance!

STOP!

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

For Your Safety

• Do not try to light any appliance. Do not touch

any electrical switch; do not use any phone in

your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

fire department.

Installation and service must be performed

by a qualified installer, service agency or the

gas supplier.

This cooktop has been design certified by CSA

International. You’ll find safety precautions in

your Owner’s Manual. Read them carefully.

This Appliance must be electrically

grounded. Check with your local codes

which apply in your area. If no local codes

apply, the National Electrical Code, ANSI/

NFPA No. 70-Latest Edition must be

followed. Write to:

National Fire Protection Association

Batterymarch Park

Quincy, MA 02269

Be sure the installation of this cooktop

in a mobile home conforms with the

Manufactured Home Construction and

Safety Standard, Title 24 CFR, Part 3280.

If this standard does not apply, you must

follow the standard for Manufactured Home

Installations, ANSI A225.1 and Manufactured

Home Installations, Sites and Communities

and ANSI/NFPA 501A or with local codes.

You can get a copy of the Federal Standard

by Writing:

Office of Mobile Home Standards

HUD Building

451 7th Street, S.W.

Washington, D.C. 24010

Electrical

Requirements

WHAT TO DO IF YOU SMELL

GAS:

Remove Installation Instructions

from literature pack and read them

carefully before you begin.

Be sure to place all literature,

Owner’s Manual, Installations, etc.

in a safe place for future reference.

Make sure you have all the tools and

materials you need before starting the

installation of the cooktop.

Your home must provide the adequate

electrical service needed to safely and

properly use your cooktop. (Refer to

section on electrical requirements.)

Remove packaging materials and

literature package from the cooktop

before beginning installation.

When preparing cooktop opening,

make sure the inside of the cabinet

and the cooktop do not interfere with

each other. (See section on preparing

the opening.)

When installing your cooktop in your

home, make sure all local codes and

ordinances are followed exactly as

stated.

Pre-Installation Checklist

EASY INSTALLATION OF YOUR NEW

30" COOKTOP

Before you begin-Read these instructions completely and carefully.

IMPORTANT- Save these instructions for local inspector's use.

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave these instructions with the consumer.

OWNER- Keep these instructions for future reference.

Note- This appliance must be properly grounded (if applicable).

Before you begin-Read these

instructions completely and

carefully.

IMPORTANT- Save these

instructions for local inspector's use.

IMPORTANT- OBSERVE ALL

GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave

these instructions with the consumer.

OWNER- Keep these instructions

for future reference.

Note- This appliance must be

properly grounded (if applicable).

FOR YOUR SAFETY

Before you begin-Read these instructions completely and carefully.

IMPORTANT- Save these instructions for local inspector's use.

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave these instructions with the consumer.

OWNER- Keep these instructions for future reference.

Note- This appliance must be properly grounded (if applicable).

Before you begin-Read these instructions completely and carefully.

IMPORTANT- Save these instructions for local inspector's use.

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave these instructions with the consumer.

OWNER- Keep these instructions for future reference.

Note- This appliance must be properly grounded (if applicable).

ELECTRICAL REQUIREMENTS

Before you begin-Read these

instructions completely and

carefully.

IMPORTANT- Save these

instructions for local inspector's use.

IMPORTANT- OBSERVE ALL

GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave

these instructions with the consumer.

OWNER- Keep these instructions

for future reference.

Note- This appliance must be

properly grounded (if applicable).

Before you begin-Read these

instructions completely and

carefully.

IMPORTANT- Save these

instructions for local inspector's use.

IMPORTANT- OBSERVE ALL

GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave

these instructions with the consumer.

OWNER- Keep these instructions

for future reference.

Note- This appliance must be

properly grounded (if applicable).

Before you begin-Read these

instructions completely and

carefully.

IMPORTANT- Save these

instructions for local inspector's use.

IMPORTANT- OBSERVE ALL

GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave

these instructions with the consumer.

OWNER- Keep these instructions

for future reference.

Note- This appliance must be

properly grounded (if applicable).

Installation Instructions

Make sure the wall coverings,

countertop and cabinets around the

cooktop can withstand heat (up to

200°F) generated by the cooktop.

Styrofoam

Packaging

Literature Package

Cooktop

The following MINIMUM clearance

dimensions must be maintained.

To insure accuracy, it is best to make

a template when cutting the opening

in the counter.

The recommended Gas Supply

Location from the backwall.

Overall cooktop dimensions

Cutout dimensions

of the countertop

Installation Instructions

Make sure the wall coverings,

countertop and cabinets around the

cooktop can withstand heat (up to

200°F) generated by cooktop.

Wall covering,

cabinets and

countertop

must withstand

heat up to 200°F.

COOKTOP

36"

21"

18 7/8"

33 11/16"

2 1/4" Min.

Between cutout

and the wall behind

the cooktop

19 1/8" width of cut

33 7/8"

length of

cut

2 1/2"Min.

from front edge

of cutout

and front edge

of countertop

16 15/16"

3 3/4" MIN.

clearance from

cutout to side

wall on the left

of the unit

30" MIN.

clearance from

countertop to

unprotected

overhead surface

3 3/4 MIN.

clearance from

cutout to side

wall on the right

of the unit

13" MAX. Depth

of unprotected

overhead cabinets

18" MIN.

height from

countertop to

nearest cabinet on

either side of unit

From Cutout

Center Line

1" Min. From Backwall

Recommended

gas supply

location.

3 3/4"

PREPARING THE OPENING

Installation Instructions

Attach the Adhesive Strip

(Glass Top Models Only)

Attach the adhesive strip around the maintop

glass as close to the edge as possible.

Cooktop

Burner

Box

Outer edge

of glass bottom

Adhesive Strips

to outer edge

of glass

Countertop

Attach Brackets to Cooktop

Remove the screw from the side of the

cooktop. Screw the hold down bracket to the

side of the cooktop unit. Repeat for opposite

side of cooktop.

Locate the electrical outlet

and the Gas Shut Off valve

beneath the cabinet.

Shut Off

Valve

Electrical

Outlet

12" Below

Countertop

Install a manual shutoff valve in the gas line

in an easily accessible location outside the

cooktop. Be sure you know how and where to

shut off the gas supply to the cooktop. Install the

electrical outlet 12" below the countertop.

NEVER REUSE

OLD CONNECTORS

WHEN INSTALLING

THIS UNIT.

Protect the Surface

of the Cooktop

Place a towel or tablecloth onto the countertop.

Lay the cooktop upside down onto the protected

surface.

Bottom of cooktop

Cloth under Cooktop

Locate The Mounting Parts

Remove the hold down brackets from the

literature package.

Insert Cooktop Into Cutout

Insert the cooktop centered into the cutout

opening. Make sure the front edge of the

countertop is parallel to the cooktop. Make

final check that all required clearances are met.

Once the unit is in place, screw the hold

down bracket into the cabinet sides to

secure the unit into place.

Foam Strips

Bottom of

Cooktop

Glass

Pre-drilled

hole

COOKTOP

Installing the Cooktop Unit

Installation Instructions

This cooktop is designed to operate on natural

gas at 4" of water column pressure. It is

shipped from the factory set for natural gas.

The convertible pressure regulator supplied

with the unit must be connected in series with

the manifold of the cooktop and must remain

in series with the supply line regardless of

whether natural or L.P. gas is being used.

FOR PROPER OPERATION, THE MAXIMUM

INLET PRESSURE TO THE REGULATOR

MUST BE NO MORE THAN 14" OF WATER

COLUMN PRESSURE. For checking the

regulator, the inlet pressure must be at least

1" (or 3.4 KPA) greater than the regulator

output setting. If the regulator is set for 4" of

water column pressure, the inlet pressure

must be at least 5". If the regulator is set for

10", the inlet pressure must be at least 11".

The gas supply line to the cooktop should be

1/2" or 3/4" pipe.

Provide Adequate Gas

Supply

Installing the Regulator

WARNING: Never reuse old flexible

connectors. The use of old flexible

connectors can cause gas leaks and

personal injury. Always use new

flexible connectors when installing

a gas appliance.

Screw a section of pipe

onto each end of the

pressure regulator.

Install the regulator onto

the burner box bottom.

Pressure

Regulator

Shut Off

Valve

Electrical

Outlet

12" Below

Countertop

Screw the

regulator and

pipe connection

into the burner

box bottom.

Make sure the

top of the

regulator is

facing toward

the cabinet front,

easily accessible

through the

cabinet doors.

Complete the connection

with a coupling.

Install a coupling

between the

regulator and the

shutoff valve to

complete the

connection.

Pressur

Regulator

Shut Off

Valve

Coupling

Electrical

Outlet

12" Below

Countertop

continue on the following page

NEVER REUSE OLD CONNECTORS WHEN

INSTALLING THIS COOKTOP.

To reduce the likelihood of gas leaks, apply

teflon tape or a thread compound approved

for use with LP or natural gases to all

threaded connections.

Pressure

Regulator

Pressure

Installing the Cooktop

Installation Instructions

Check for Leaks

After connecting the cooktop to gas, check

system for leaks with a manometer. If a

manometer is not available, turn the gas

supply on to the cooktop and use a liquid

leak detector at all joints and connections

to check for leaks.

Tighten all connections if necessary to

prevent gas leakage in the cooktop or

supply line.

Check alignment of valves after connecting

the cooktop to the gas supply to be sure the

manifold pipe has not been moved. A

misalignment could cause the valve knob

stem to rub on the control panel, resulting

in a gas leak at the valve.

DO NOT USE OPEN FLAME TO CHECK

FOR LEAKS!

Disconnect this cooktop and its individual

shutoff valve from the gas supply piping

system during any pressure testing of that

system at test pressures greater than 1/2" psig.

Isolate the cooktop from the gas supply

piping system by closing its individual shutoff

valve during any pressure testing of the gas

supply system at test pressures equal to or

less than 1/2" psig.

INSTALLATION OVER

BUILT-IN OVEN

See built-in oven installation for complete

installation instructions.

90°

STREET EL

CABINET SIDES

2" DIA. HOLE (20 7/8"

FROM FRONT OF

COUNTERTOP TO

HOLE CENTER)

5" TO CENTER

OF 2" DIA. HOLE

FROM COUNTERTOP

Installing the Cooktop cont.

Installation Instructions

Because of potential safety hazards

under certain conditions, we strongly

recommend against the use of an

extension cord. However, if you still elect

to use an extension cord, it is absolutely

necessary that it be a UL listed 3-wire

grounding type appliance extension cord

and that the current carrying rating of the

cord in amperes be equivalent to or

greater than the branch circuit rating.

Such extension cords are obtainable

through your local appliance dealer.

IMPORTANT: (Please read carefully) FOR

PERSONAL SAFETY, THIS APPLIANCE

MUST BE PROPERLY GROUNDED.

An adequate electrical supply and outlet

must be used to operate the electrical

parts of your cooktop.

Insure proper

ground and

firm connection

before use

Where a standard two-prong wall

receptacle is encountered, it is the

personal responsibility and obligation of

the customer to have it replaced with a

properly grounded three-prong wall

receptacle.

Do not under any circumstances cut or

remove grounding prong from the

cooktop cord. Failure to provide proper

polarization may create a hazardous

condition.

a. The power cord of this appliance is

equipped with a three-prong (grounding)

plug which must be used with a properly

grounded three-hole outlet with a standard

120 Volt, 60 cycle AC household current.

b. If you do not have a three-hole grounded

outlet, have a qualified electrician change

your old one.

c. A grounding adaptor will be needed to

convert the old one until the outlet can be

replaced. This method is only temporary,

and a qualified electrician should test it to

be sure it meets requirements.

continued on following page

Installation—Electrical Connections

Usage situations where

appliance power cord will be

disconnected infrequently.

Temporary Method

(Adaptor plugs not permitted

in Canada)

Align large

prongs/slots

Insure proper ground

and firm connection

before use

For 15 amp circuit only. Do not use an adaptor

on a 20 amp circuit. Where local codes permit, a

TEMPORARY CONNECTION may be made to

a properly grounded two-prong wall receptacle

by the use of a UL listed adaptor available at

most hardware stores. The larger slot in the

adaptor must be aligned with the large slot in the

wall receptacle to provide proper polarity in the

connection of the power cord.

Installation Instructions

CAUTION: Attaching the adaptor

ground terminal to the wall receptacle

cover screw does not ground the

appliance unless the screw is metal,

and not insulated, and the wall

receptacle is grounded through the

house wiring. The customer should

have the circuit checked by a

qualified electrician to make sure

the receptacle is properly grounded.

When disconnecting the power cord from the

adaptor, always hold the adaptor with one

hand. If this is not done, the adaptor ground

terminal is very likely to break with repeated

use. Should this happen, DO NOT USE the

appliance until a proper ground has again

been established.

Usage situations where appliance power

cord will be disconnected frequently.

Do not use an adaptor plug in these situations

because disconnection of the power cord

places undue strain on the adaptor and leads

to eventual failure of the adaptor ground

terminal. The customer should have the two-

prong receptacle replaced with a three-prong

(grounding) receptacle by a qualified

electrician before using the appliance.

Installation—Electrical Connections

Installation Instructions

The electrode of the spark igniter is exposed. Be careful not to push any cooktop controls while

the top of the burner is removed. Do not remove the top or touch the electrode of any burner while

another burner is turned on. Electrical shock might result.

Assembling the Cooktop Burners

a. Place the burner head on the burner bowl, so that the location of the spark igniter matches up with

the opening in the burner head.

b. Position the burner cap on the burner head.

c. Place the burner grate over the burner assembly and into the burner bowl. The bottoms of the

burner grates have fingers that fit into the corresponding indentations in the burner bowl.

BURNER

BOWL

SPARK IGNITER

BURNER GRATE

BURNER CAP

BURNER HEAD

MIXER TUBE

(CHIMNEY)

MIXER TUBE

Cooktop Burners

Installation Instructions

Checking the Igniters

Operation of the electric igniters should be

checked after the cooktop and supply line

have been carefully checked for leaks and

the cooktop has been connected to the

electrical power.

a. Push and turn a burner valve to the LITE

position.

• The burner valve should light when gas

is available to the burner

• Once the burner lights, it should be

turned out of the LITE position.

b. Try each valve separately until all burners

have been checked.

Cooktop Spark Ignition—When you turn the

cooktop knob to LITE, the spark igniter

makes a series of electric sparks (ticking

sounds) which light the burner.

During a power failure, the burners will not

light automatically. In an emergency, a

cooktop burner may be lit with a match by

following the steps below.

WARNING: Lighting gas burners with a

match is dangerous. You should match

light the cooktop burners only in an

emergency.

Burner Ignition

a. Light a match and hold the flame near the

burner you want to light. Wooden matches

work best.

b. Push in and turn the control knob slowly. Be

sure you are turning the correct knob for the

burner you are lighting.

NOTE: If the burner does not light within five

seconds, turn the knob off and wait one minute

before trying again.

The Burner Flames

Turn each burner on. Flames should be blue

in color with no trace of yellow. The burner

flames should not flutter or blow away from

the burner. The inner cone of the flame

should be between 1/2" to 3/4" long.

Burners should be checked frequently

WARNING: If you attempt to measure

the inner cone of the flame, please use

caution. Burns could result.

Cooktop

Burner

1/2" to 3/4"

Cooktop Burners cont.

Installation Instructions

Operation Checklist

Double check to make sure

everything in this guide has been

completed. Rechecking steps will

ensure safe use of the cooktop.

Make sure all controls are left in

the OFF position.

Make sure the flow of

combustion and ventilation air to

the cooktop is unobstructed.

The serial plate for your cooktop

is located on the bottom of the

burner box. In addition to the

model and serial numbers, it tells

you the ratings of the burners

and the type of fuel and pressure

the cooktop was adjusted for

when it left the factory.

Recheck Steps:

Double check to make sure

everything in this guide has been

completed. Rechecking steps will

ensure safe use of the cooktop.

When ordering parts, always

include the serial number, model

number and a code letter to ensure

proper replacement parts.

LP Conversion

The pressure regulator and burner orifices

are set for natural gas. To use propane

gas, the regulator and burner orifices

must be converted. The LP orifice spuds

for the cooktop burners can be located in

the literature package.

CAUTION: The cooktop, as shipped

from the factory, is set for use with

natural gas. If you wish to use your

cooktop with Liquefied Petroleum

(Propane) gas, you must first replace

the orifices and convert the pressure

regulator.

To adjust your cooktop

for use with LP gas,

follow these instructions:

WARNING: This conversion must be

performed by a qualified installer or gas

supplier in accordance with the

manufacturer’s instructions and all codes

and requirements of the authority having

jurisdiction. Failure to follow instructions

could result in serious injury or property

damage. The qualified agency performing

this work assumes responsibility for the

conversion.

a. Disconnect all electrical power, at the main

circuit breaker or fuse box.

b. Shut off the gas supply to the cooktop by

closing the manual shut-off valve.

c. Adjust the pressure regulator by the

following instructions:

• Unscrew the cap.

• Place your thumb against the flat side

of the spring retainer and press down

to remove the retainer.

• Carefully look at the spring retainer to

locate the NAT or LP position.

Safety Information you

should know

NAT.

POSITION

L.P./PROPANE

POSITION

CAP

SPRING

RETAINER

DOWN

FOR OFF

NAT

GASKET

PRESSURE REGULATOR

NAT

• Turn the spring retainer over so that

LP is showing on the bottom.

• Snap the retainer back into position.

continued on following page

Making the L.P. Conversion

LP Conversion

Changing the Cooktop

Burner Orifices:

NOTE: The orifices have a spring loaded

retaining ring around the

hex head to hold the orifice

in the nut driver during

installation and removal.

A slight amount of force is

required to push the nut

driver down over the ring.

RETAINER

RING

c. Locate the LP/Propane orifices shipped

inside the literature package. They will have

a digit number and the letter “L” on the side.

(IMPORTANT: Save the orifices removed

from the appliance for future use.)

Each orifice will show a series of engraved

marks, (I, II or III), located on the top.

d. Install the LP/Propane orifices in their

precise locations as noted in the illustration

above.

e. Replace the burner bases, heads, caps and

top grates. (NOTE: When re-attaching the

burner bases to glass top units, tighten

screws to a maximum of 10 in.-lbs torque.)

f. Save the orifices removed from the appliance

for future use.

continued on following page

These marks denote the precise location

of each orifice to the cooktop burner.

b. Using a 7mm or 9/32" nut driver, remove the

top burner orifices. These may be accessed

through the hole in the cooktop.

BURNER

BOWL

SPARK IGNITER

BURNER GRATE

BURNER CAP

BURNER HEAD

MIXER TUBE

(CHIMNEY)

MIXER TUBE

a. Remove the top grates, burner caps and

burner heads.

MIXER TUBE (CHIMNEY)

Glass Cooktop

III

Making the L.P. Conversion cont.

LP Conversion

Adjusting the Burner

Flames

CAUTION: The following adjustments

must be made before turning on the

burner. Failure to do so could result

in serious injury. Be sure pressure

regulator has been converted as

described in step F2.

a. Turn all burners full on and check the

flames.

Foreign particles in the gas line may cause

an orange flame at first, but this will soon

disappear.

b. To make adjustments, remove the control

knobs. Insert a screwdriver through access

hole in the valve switch. Engage adjustment

screw in valve.

• If the flames were too small or fluttered,

open the valve more than the original

setting.

• If the flames blew away from the burner,

close the valve more than the original

setting.

c. Make the adjustment by slowly turning the

screw until flame appearance is correct.

Adjust the low flame setting using the valve

by-pass screw as follows:

Low setting adjustments must be made with two

other burners in operation on a medium setting.

This prevents the low flame from being set too

low, resulting in the flame being extinguished

when other burners are turned on.

d. Testing flame stability:

Test 1 - Turn the knob from “HI” to “LOW”

quickly. If the “LOW” flame goes

out, increase the flame size and

test again.

Test 2 - With the burner on the “LOW”

setting, open and close the cabinet

door under the cooktop. If the

flame is extinguished by the air

currents created by the door

movement, increase the flame

height and test again.

e. Flame recheck:

After the adjustment is made, turn all burners

off. Ignite each burner individually. Observe

the flame at the “HI” position. Rotate the valve

to the “LO” position and be sure that the flame

size decreases as the valve is rotated

counterclockwise.

TO CONVERT THE COOKTOP BACK TO

NATURAL GAS, REVERSE THE STEPS

UNDER MAKING THE LP CONVERSION.

Once the conversion is complete and

checked ok, fill out the LP sticker and

include your name, organization and date

conversion was made. Apply the sticker

near the cooktop gas inlet opening to alert

others in the future that this appliance has

been converted to LP gas. If converting

back to natural gas from LP, please

remove the sticker so others know the

appliance is set to use natural gas.

HIGH OUTPUT

Making the L.P. Conversion cont.

NOTES

Table de cuisson scellée au gaz

de 91 cm (36 po)

Instructions

d’installation

MISE EN GARDE : Avant de commencer, lisez

attentivement la totalité de ces instructions.

• IMPORTANT—Conservez ces instructions

pour votre inspecteur local.

• IMPORTANT—Respectez toutes les

ordonnances et les codes locaux.

• Note à l’installateur : Assurez-vous de

laissez ces instructions au consommateur.

• Note au consommateur—Conservez ces

instructions pour référence future.

•Note—Cet appareil coit être bien mis à la terre.

PIÈCES COMPRISES

Perceuse à main ou

électrique et foret

de 1/8 po

Tournevis

Phillips

Crayon

Règle

ordinaire ou

de vérification

Agent de

scellement

de tuyau

Scie

sauteuse

2 vis

OUTILS DONT VOUS AUREZ BESOINS

229C4053P464-1

31-10505-1 (05-03 JR)

2 Supports

de fixation

Raccords de

tuyaux

Questions? Appelez le Centre de réponse GE au 1.800.361.3400 ou visitez

notre site Web à l’adresse : www.electromenagersge.ca

MATÉRIAUX NÉCESSAIRES

JGP636, JGP960

Bandes de

mousse

Robinet

d’alimentation

de gaz

Clé à tuyau

• IMPORTANT : Vous devez vérifier que cet

appareil n’a pas de fuite conformément aux

instructions du fabricant.

Dans le Commonwealth of Massachusetts :

•

Vous devez faire installer ce produit par

un plombier

licencié ou un monteur

d’installations au gaz.

• Si vous utilisez des robinets d’arrêt de gaz

à verrouillage à bille, ces robinets doivent

être de la catégorie à manche en T.

• Si vous utilisez un tuyau de jonction du gaz,

celui-ci ne doit pas dépasser 1 mètre (3 pieds).

Avertissement!! Si vous ne suivez

pas exactement les instructions de

ce manuel, vous risquez

d’occasionner un incendie, une explosion

ou une fuite de gaz, qui peuvent provoquer

des dommages matériels, des blessures

corporelles ou la mort.

• L’installation de votre table de cuisson doit se

conformer aux codes locaux ou, en l’absence de codes

locaux, au National Fuel Gas Code, ANSI Z223.1

Dernière édition.

• Assurez-vous que votre table de cuisson soit bien

installée par un installateur qualifié ou un technicien de

service.

• Pour éliminer tout mouvement corporel au dessus des

brûleurs de votre table de cuisson, évitez de placer des

aromires de cuisine au dessus des brûleurs.

• N’installez janais votre appareil près d’une porte d’entrée

ou à un emplacement où un courant d’air peut gêner son

usage.

NE CONSERVEZ PAS OU N’UTILISEZ JAMAIS

D’ESSENCE OU D’AUTRES LIQUIDES OU VAPEURS

INFLAMMABLES À PROXIMITÉ DE

CET APPAREIL OU DE TOUT AUTRE

APPAREIL MÉNAGER!

STOP!

Instructions d’installation

INSTRUCTIONS IMPORTANTES EN MATIÈRE DE SÉCURITÉ

POUR VOTRE SÉCURITÉ

• N’essayez jamais d’allumer un appareil

électroménager. Ne touchez à aucun commutateur

d’électricité, n’utilisez jamais un téléphone dans votre

bâtiment.

• Appelez immédiatement votre fournisseur de gaz à

l’aide du téléphone d’un voisin. Suivez les instructions

de votre fournisseur de gaz.

• Si vous ne pouvez pas entrer en communication avec

votre fournisseur de gaz, appelez les pompiers.

L’installation et service de votre table de cuisson doivent

être faites par un installateur qualifié, un technicien de

service ou votre fournisseur de gaz.

La conception de votre table de cuission a été approuvé

par l’ACNOR International. Vous trouverez des

précautions ô prendre en matière de sécurité dans votre

Manuel d’utilisation. Lisez-les attentivement.

Cet appareil doit être mis à la terre. Vérifiez les

codes locaux qui s’appliquent dans votre région. Si

aucun code local ne s’applique, conformez-vous au

National Electrical Code, ANSI NFPA N° 70 Dernière

édition. Pour de plus amples renseignements, écrivez

à l’adresse suivante:

National Fire Protection Association

Batterymarch Park

Quincy, MA 02269

Assurez-vous que l’installation de cette table de

cuisson dans une maison mobile se conforme à la

Manufactured Home Construction and Safety

Standard, Title 24 CFR, Part 3280. Si cette norme ne

s’applique pas, vous devez vous conformer à la

norme Standard for Manufactured Home Installations,

Sites and Communities et ANSI/NFPA 501A, ou aux

codes locaux. Vous pouvez obtenir un exemplaire de

la norme fédérale en écrivant à l’adresse suivante :

Office of Mobile Home Standards

HUD Building

451 7th Street, S.W.

Washington, D.C. 24010

BESOINS D’ÉLECTRICITÉ

CI QUE VOUS DEVEZ FAIRE SI VOUS

SENTEZ LE GAZ :

Enlevez les instructions d’installation

de la trousse de documentation et lisez-les

soigneusement avant de commencer.

Assurez-vous de bien ranger toute la

documentation, Manuel d’utilisation, les

installations, etc. dans un endroit sûr pour

référence future.

Assurez-vous d’avoir tous les outils et tous les

matéraux nécessaires avant de commencer à

installer votre table de cuisson.

Votre maison doit être alimentée en courant

électrique adéquat pour vous permettre de

bien utiliser en toute sécuité votre table de

cuisson. (Consultez la section sur les besoins

d’électricité)

Retirez les matériaux d’emballage et la

trousse de documentation de votre table de

cuisson avant de commencer à l’installer.

Pour préparer l’ouverture de la surface de

cuisson, vous devez vous assurer que

l’intérieur de l’armoire ne touche pas la table

de cuisson (consultez la section sur la

préparation de l’ouverture).

Pour installer votre table de cuisson dans

votre maison, assurez-vous de vous

conformer scrupuleusement à tous les codes

et à toutes les ordonnances locales.

LISTE DE VÉRIFICATION AVANT INSTALLATION

EASY INSTALLATION OF YOUR NEW

30" COOKTOP

Before you begin-Read these instructions completely and carefully.

IMPORTANT- Save these instructions for local inspector's use.

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave these instructions with the consumer.

OWNER- Keep these instructions for future reference.

Note- This appliance must be properly grounded (if applicable).

Before you begin-Read these

instructions completely and

carefully.

IMPORTANT- Save these

instructions for local inspector's use.

IMPORTANT- OBSERVE ALL

GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave

these instructions with the consumer.

OWNER- Keep these instructions

for future reference.

Note- This appliance must be

properly grounded (if applicable).

FOR YOUR SAFETY

Before you begin-Read these instructions completely and carefully.

IMPORTANT- Save these instructions for local inspector's use.

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave these instructions with the consumer.

OWNER- Keep these instructions for future reference.

Note- This appliance must be properly grounded (if applicable).

Before you begin-Read these instructions completely and carefully.

IMPORTANT- Save these instructions for local inspector's use.

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave these instructions with the consumer.

OWNER- Keep these instructions for future reference.

Note- This appliance must be properly grounded (if applicable).

ELECTRICAL REQUIREMENTS

Before you begin-Read these

instructions completely and

carefully.

IMPORTANT- Save these

instructions for local inspector's use.

IMPORTANT- OBSERVE ALL

GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave

these instructions with the consumer.

OWNER- Keep these instructions

for future reference.

Note- This appliance must be

properly grounded (if applicable).

Before you begin-Read these

instructions completely and

carefully.

IMPORTANT- Save these

instructions for local inspector's use.

IMPORTANT- OBSERVE ALL

GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave

these instructions with the consumer.

OWNER- Keep these instructions

for future reference.

Note- This appliance must be

properly grounded (if applicable).

Before you begin-Read these

instructions completely and

carefully.

IMPORTANT- Save these

instructions for local inspector's use.

IMPORTANT- OBSERVE ALL

GOVERNING CODES AND ORDIANCES.

Note to Installer- Be sure to leave

these instructions with the consumer.

OWNER- Keep these instructions

for future reference.

Note- This appliance must be

properly grounded (if applicable).

Instructions d’installation

Assurez-vous que les revêtements de mur,

le comptoir et les armoires autour de la table

de cuisson puissent supporter la chaleur

[pouvant atteindre 93°C (200°F)] produite par

la table de cuisson.

Emballage

en mousse

polystyrène

Trousse de

documentation

Table de

cuisson

Vous devez respecter les dégagements

minimaux suivant :

Pour assurer la justesse du découpage,

il vaut mieux faire un gabarit pour couper

l’ouverture dans le comptoir.

Emplacement recommandé de l’alimentation

de gaz à partir du mur arrière.

Dimensions du découpage

de la table de cuisson

Instructions d’installation

Assurez-vous que les revêtements mur, le

comptoir et les armoires autour de la table de

cuisson puissent supporter la chaleur [pouvant

atteindre 93°C (200°F)].

Dimensions totales

de la table de cuisson

Distance min de

5.7 cm (2 1/4") de

découpage

au mur derrière

la table de cuisson

largeur du découpage

49.8 cm

(19 5/8")

72.4 cm

(28 1/2 po)

longueur du

découpage

6.4 cm

(2 1/2") Distance min.

de l'arête avant du

découpagede l'arrête

avant de la table de cuisson

36.2 cm

(14 1/4")

Dégagement min

de 10 cm (3 3/4")

du découpage au

mur de côté droite

de l'appareil

Dégagement min.

de 76cm (30") du

comptoir à la

surface en non

surplomb non

protégées

Dégagement min.

de 10 cm (3 3/4")

découpage

au mur de

côté à droite

de l'appareil

Profondeur max

de 33cm (13")

des armoires en

surplomb non

protégées

Hauteur min de 45 cm

(18") du comptoir à

l'armoire la plus proche

de chaque côté

de l'appareil

découpage de l'arrête

avant de la table de cuisson

Les revêtements de

mur, les armoires et

le comptoir doivent

pouvoir supporter

une chaleur pouvant

atteindre 93°C (200°F)

From Cutout

Center Line

1" Min. From Backwall

Recommended

gas supply

location.

2.5 cm (1") min.

du mur arrière

23 cm

(9")

Du découpage

à la ligne du

centre

Emplacement

recommandé

de l’alimentation

de gaz

COOKTOP

36"

21"

18 7/8"

33 11/16"

Table de cuisson

8 cm

(3")

85.5 cm

(33 11/16")

48 cm

(18 7/8")

91.4 cm

(36")

53 cm

(21")

48.5 cm

(19 1/8")

43 cm

(16 15/16")

86 cm

(33 7/8")

Préparation de l’ouverture

La page charge ...

GE JGP636CEDCC Guide d'installation

Marque: GE

Modèle: JGP636CEDCC

Catégorie: Cuisinières

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: GE JGP636CEDCC Installation guide

GE JGP636CEDCC Guide d'installation

Ce manuel convient également à

GE JGP636CEDCC Guide d'installation

dans d''autres langues

Documents connexes

Autres documents