Hotpoint EDPE 745 A2 ECO EU Mode d'emploi
- Catégorie
- Sèche-linge
- Taper
- Mode d'emploi
GB
1
EDPE 745 A2
www.indesit.com
Instruction booklet
English, 1
GB
TUMBLE DRYER
Contents
Installation, 2
Warnings, 4
Care and Maintenance, 6
Control Panel, 8
Laundry, 8
The Display, 9
Start and Programmes, 11
Troubleshooting, 15
Service, 16
This symbol reminds you to read this in-
struction manual.
!
Keep this manual at hand for immediate reference whenever
necessary. Always store this manual close to the tumble dryer and
remember to pass it on to any new owners when selling or tran-
sferring the appliance, so they may familiarise with the warnings
and suggestions herein contained.
! Read these instructions carefully: the following pages contain
important information on installation and useful suggestions for
operating the appliance.
Nederlands, 17
NL
2
GB
Where to put your dryer
The dryer should be
installed in an ambient
room temperature of
between 20 to 23°C for
optimum performance. But
will function if the room is
between 14 and 30°C. If
you are going to install the
appliance under a work
counter, be sure to leave a 10 mm space
between the top and any other objects on
or above the machine and a 15 mm space
between the sides and lateral furnishings or
walls. This is to ensure proper air circulation.
The appliance must be installed with the rear
surface placed against a wall.
Ventilation
Make sure you put your dryer in an environment
that is not damp and has proper air circulation
throughout. Airflow around the dryer is essential to
condense the water produced during the washing,
the dryer will not operate efficiently in an enclosed
space or cupboard.
If using the dryer in a small or cold room
some condensation will be experienced.
Water Drain
If the machine is positioned close to a drain it is possible to drain the
condensed water directly without using the waterbottle. In which
case it is no longer necessary to empty the water bottle at the end
of each cycle. If the Dryer is positioned above or close to a Washing
Machine the same drainage can be used. Just remove the tube
indicated in figure A and connect it to the drainage. If the drainage
is further away than the length of the tube it is possible to buy and
connect a tube of the same diameter and the necessary length in
order to reach the drain. To install the new tube just substitute the
existing one as indicated in figure B inserting it in the same place.
The drain tube has to be below 1 m from the bottom of the
Dryer.
Once the Dryer has been installed please assure that the
drain tube is not bent or kinked.
1
2
2
1
Less than 1m
Fig. A Fig. B
We do not recommend that the dryer is
installed in a cupboard but the dryer must never
be installed behind a lockable door, a sliding
door or a door with a hinge on the opposite
side to that of the dryer door.
Electrical connections
Before plugging the appliance into the socket,
check the following:
Make sure your hands are dry.
The socket must have an earth
connection.
The socket must be able to withstand the
machine’s maximum power output as
indicated on the rating plate (see
Description of the tumble dryer)
The power supply voltage must fall within
the values indicated on the data plate (see
Description of the tumble dryer).
Do not use extension leads. Do not pull the
power supply cable. Do not use multiple
plug adaptors if the appliance is fitted with
a plug. For appliances with fitted plug, if the
plug is not suitable for you socket outlet,
contact a qualified technician.
The dryer must not be installed outdoors,
even if the space is sheltered.
Once installed, the dryer’s electrical wire
and plug must be within reach.
The power cord must not be bent or
squashed.
If the plug being replaced is a non-rewirable
type, then the cut-off plug must be disposed of
safely. DO NOT leave it where it can be inserted
into a socket and create a shock hazard.
The power must be regularly checked. If
the supply cord is damaged, it must be
replaced by the service agent (see
Assistance).
The manufacturer denies any
responsibility should any of these rules
not be followed.
If in doubt about any of the above
consult a qualified electrician.
Levelling the tumble dryer
The dryer must be installed level for correct
operation.
When you have installed your dryer in its final
location check that it is level first side-to-side,
then front to back. If the dryer is not level,
adjust the two legs up or down until your
dryer is level.
Preliminary information
Once you’ve installed your dryer and before you use it, clean
the inside of the drum to remove any dust that could have
accumulated during transportation.
Warning ! Before you use your dryer ensure that its has
been in a upright position for at least 6 hours.
Installation
10 mm
15 mm
15 mm
GB
3
Maximum load sizes: 7 kg
Where to put your dryer
The dryer should be
installed in an ambient
room temperature of
between 20 to 23°C for
optimum performance. But
will function if the room is
between 14 and 30°C. If
you are going to install the
appliance under a work
counter, be sure to leave a 10 mm space
between the top and any other objects on
or above the machine and a 15 mm space
between the sides and lateral furnishings or
walls. This is to ensure proper air circulation.
The appliance must be installed with the rear
surface placed against a wall.
Ventilation
Make sure you put your dryer in an environment
that is not damp and has proper air circulation
throughout. Airflow around the dryer is essential to
condense the water produced during the washing,
the dryer will not operate efficiently in an enclosed
space or cupboard.
If using the dryer in a small or cold room
some condensation will be experienced.
Water Drain
If the machine is positioned close to a drain it is possible to drain the
condensed water directly without using the waterbottle. In which
case it is no longer necessary to empty the water bottle at the end
of each cycle. If the Dryer is positioned above or close to a Washing
Machine the same drainage can be used. Just remove the tube
indicated in figure A and connect it to the drainage. If the drainage
is further away than the length of the tube it is possible to buy and
connect a tube of the same diameter and the necessary length in
order to reach the drain. To install the new tube just substitute the
existing one as indicated in figure B inserting it in the same place.
The drain tube has to be below 1 m from the bottom of the
Dryer.
Once the Dryer has been installed please assure that the
drain tube is not bent or kinked.
1
2
2
1
Less than 1m
Fig. A Fig. B
We do not recommend that the dryer is
installed in a cupboard but the dryer must never
be installed behind a lockable door, a sliding
door or a door with a hinge on the opposite
side to that of the dryer door.
Electrical connections
Before plugging the appliance into the socket,
check the following:
Make sure your hands are dry.
The socket must have an earth
connection.
The socket must be able to withstand the
machine’s maximum power output as
indicated on the rating plate (see
Description of the tumble dryer)
The power supply voltage must fall within
the values indicated on the data plate (see
Description of the tumble dryer).
Do not use extension leads. Do not pull the
power supply cable. Do not use multiple
plug adaptors if the appliance is fitted with
a plug. For appliances with fitted plug, if the
plug is not suitable for you socket outlet,
contact a qualified technician.
The dryer must not be installed outdoors,
even if the space is sheltered.
Once installed, the dryer’s electrical wire
and plug must be within reach.
The power cord must not be bent or
squashed.
If the plug being replaced is a non-rewirable
type, then the cut-off plug must be disposed of
safely. DO NOT leave it where it can be inserted
into a socket and create a shock hazard.
The power must be regularly checked. If
the supply cord is damaged, it must be
replaced by the service agent (see
Assistance).
The manufacturer denies any
responsibility should any of these rules
not be followed.
If in doubt about any of the above
consult a qualified electrician.
Levelling the tumble dryer
The dryer must be installed level for correct
operation.
When you have installed your dryer in its final
location check that it is level first side-to-side,
then front to back. If the dryer is not level,
adjust the two legs up or down until your
dryer is level.
Preliminary information
Once you’ve installed your dryer and before you use it, clean
the inside of the drum to remove any dust that could have
accumulated during transportation.
Warning ! Before you use your dryer ensure that its has
been in a upright position for at least 6 hours.
Installation
10 mm
15 mm
15 mm
Power consumption
o-mode (Po) - Watts 0.17
left-on mode (Pl) - Watts 2.36
Programs Kg kWh Minutes
Standard cotton*
7 1.80 200
Standard cotton
3.5 0.95 106
Synthetics 4 0.66 75
* This is the reference program for the energy label
and suitable to dry normal wet cotton laundry. This
is the most ecient programme in terms of energy
consumption for drying wet cotton laundry.
4
GB
Warnings
! This appliance has been designed and built
according to international safety standards.
These warnings are given for safety reasons
and must be followed carefully.
General safety
• This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved.
• This tumble dryer has been designed for
home, and not professional, use.
• Do not touch the appliance while barefoot
or with wet hands or feet.
• Unplug the machine by pulling on the plug,
not the cord.
• After using the dryer, turn it off and unplug
it. Keep the door closed to make sure that
children do not use it as a toy.
• Children should be supervised to ensure
that they do not play with the dryer.
• Cleaning and user maintenance shall not be
made by children without supervision.
•Children of less than 3 years should be
kept away from the appliance unless
continuously supervised.
• The appliance must be installed correctly
and have proper ventilation. The air intake
at the front of the dryer should never be
obstructed (see Installation).
• Never use the dryer on carpeting where
the pile height would prevent air from
entering the dryer from the base.
• Check to see if the dryer is empty before
loading it.
•
The back of the dryer could become
very hot. Never touch it while in use.
• Do not use the dryer unless the filter,
watercontainer and condenser are securely in
place (see Maintenance).
• Do not overload the dryer (see Laundry for
maximum loads).
• Do not load items that are dripping wet.
• Carefully check all instructions on clothing
labels (see Laundry).
• Do not tumble dry large, very bulky items.
• Do not tumble dry acrylic fibres at high
temperatures.
• Do not turn off the dryer when there are still
warm items inside.
• Clean the filter after each use (see
Maintenance).
• Empty the Water Container after each use
(see Maintenance).
• Clean the Heat Pump filter unit at regular
intervals (see Maintenance).
• Do not allow lint to collect around the dryer.
• Never climb on top of the dryer. It could
result in damage.
• Always follow electrical standards and
requirements (see Installation).
• Always buy original spare parts and
accessories (see Service).
To minimise the risk of fire in your tumble
dryer, the following should be observed:
• Tumble dry items only if they have been
washed with detergent and water, rinsed and
been through the spin cycle. It is a fire hazard
to dry items that HAVE NOT been washed
with water.
• Do not dry garments that have been treated
with chemical products.
• ●Do not tumble dry items that have been
spotted or soaked with vegetable or cooking
oils, this constitutes a fire hazard. Oil-affected
items can ignite spontaneously,especially
when exposed to heat sources such as
a tumble dryer. The items become warm,
causing an oxidisation reaction with the
oil, Oxidisation creates heat. If the heat
cannot escape, items can become hot
enough to catch fire. Piling, stacking or
storing oil-effected items can prevent heat
from escaping and so create a fire hazard.
If it is unavoidable that fabrics containing
vegetable or cooking oil or those that have
been contaminated withhair care products
be placed in a tumble dryer they should first
be washed with extra detergent - this will
reduce, but not eliminate the hazard. They
should not be removed from the dryer and
piled or stacked while hot.
• ●Do not tumble dry items that have previously
been cleaned in or washed in, soaked in
or soiled with petrol/gasoline, dry cleaning
solvents or other flammable or explosive
substances. Highly flammable substances
commonly used in domestic environments
including cooking oil, acetone, denatured
alcohol, kerosene, spot removers, turpentine,
waxes and wax removers. Ensure these
items have been washed in hot water with
an extra amount of detergent before being
dried in the tumble dryer.
• Do not tumble dry items containing foam
rubber (also known as latex foam), or
similarly textured rubber like materials.
Foam rubber materials can, when heated,
produce fire by spontaneous combustion.
• Fabric softener or similar products should
not be used in a tumble dryer to eliminate
the effects of static electricity unless the
practice is specifically recommended by
the manufacturer of the fabric softener
product.
• ●Do not tumble dry undergarments that
contain metal reinforcements eg. bras
with metal reinforcing wires. Damage to
the tumble dryer can result if the metal
reinforcements come loose during drying.
• ●Do not tumble dry rubber, plastic articles
such as shower caps or babies waterproof
covers, polythene or paper.
• ●Do not tumble dry rubber backed articles,
clothes fitted with foam rubber pads,
pillows, galoshes and rubber coated tennis
shoes.
• ●Remove all objects from pockets such as
lighters and matches.
! WARNING: Never stop the dryer before
the end of the drying cycle unless all
items are quickly removed and spread
out so that the heat is dissipated.
Save energy and respect the environment
• Wring out all items to eliminate excess water before
tumble drying (if you use a washing machine first, select
a high spin cycle). Doing this will save time and energy
during drying.
• Always dry full loads - you save energy: single items or
small loads take longer to dry.
• Clean the filter after each use to contain energy
consumption costs (see Maintenance).
GB
5
Warnings
! This appliance has been designed and built
according to international safety standards.
These warnings are given for safety reasons
and must be followed carefully.
General safety
• This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved.
• This tumble dryer has been designed for
home, and not professional, use.
• Do not touch the appliance while barefoot
or with wet hands or feet.
• Unplug the machine by pulling on the plug,
not the cord.
• After using the dryer, turn it off and unplug
it. Keep the door closed to make sure that
children do not use it as a toy.
• Children should be supervised to ensure
that they do not play with the dryer.
• Cleaning and user maintenance shall not be
made by children without supervision.
•Children of less than 3 years should be
kept away from the appliance unless
continuously supervised.
• The appliance must be installed correctly
and have proper ventilation. The air intake
at the front of the dryer should never be
obstructed (see Installation).
• Never use the dryer on carpeting where
the pile height would prevent air from
entering the dryer from the base.
• Check to see if the dryer is empty before
loading it.
•
The back of the dryer could become
very hot. Never touch it while in use.
• Do not use the dryer unless the filter,
watercontainer and condenser are securely in
place (see Maintenance).
• Do not overload the dryer (see Laundry for
maximum loads).
• Do not load items that are dripping wet.
• Carefully check all instructions on clothing
labels (see Laundry).
• Do not tumble dry large, very bulky items.
• Do not tumble dry acrylic fibres at high
temperatures.
• Do not turn off the dryer when there are still
warm items inside.
• Clean the filter after each use (see
Maintenance).
• Empty the Water Container after each use
(see Maintenance).
• Clean the Heat Pump filter unit at regular
intervals (see Maintenance).
• Do not allow lint to collect around the dryer.
• Never climb on top of the dryer. It could
result in damage.
• Always follow electrical standards and
requirements (see Installation).
• Always buy original spare parts and
accessories (see Service).
To minimise the risk of fire in your tumble
dryer, the following should be observed:
• Tumble dry items only if they have been
washed with detergent and water, rinsed and
been through the spin cycle. It is a fire hazard
to dry items that HAVE NOT been washed
with water.
• Do not dry garments that have been treated
with chemical products.
• ●Do not tumble dry items that have been
spotted or soaked with vegetable or cooking
oils, this constitutes a fire hazard. Oil-affected
items can ignite spontaneously,especially
when exposed to heat sources such as
a tumble dryer. The items become warm,
causing an oxidisation reaction with the
oil, Oxidisation creates heat. If the heat
cannot escape, items can become hot
enough to catch fire. Piling, stacking or
storing oil-effected items can prevent heat
from escaping and so create a fire hazard.
If it is unavoidable that fabrics containing
vegetable or cooking oil or those that have
been contaminated withhair care products
be placed in a tumble dryer they should first
be washed with extra detergent - this will
reduce, but not eliminate the hazard. They
should not be removed from the dryer and
piled or stacked while hot.
• ●Do not tumble dry items that have previously
been cleaned in or washed in, soaked in
or soiled with petrol/gasoline, dry cleaning
solvents or other flammable or explosive
substances. Highly flammable substances
commonly used in domestic environments
including cooking oil, acetone, denatured
alcohol, kerosene, spot removers, turpentine,
waxes and wax removers. Ensure these
items have been washed in hot water with
an extra amount of detergent before being
dried in the tumble dryer.
• Do not tumble dry items containing foam
rubber (also known as latex foam), or
similarly textured rubber like materials.
Foam rubber materials can, when heated,
produce fire by spontaneous combustion.
• Fabric softener or similar products should
not be used in a tumble dryer to eliminate
the effects of static electricity unless the
practice is specifically recommended by
the manufacturer of the fabric softener
product.
• ●Do not tumble dry undergarments that
contain metal reinforcements eg. bras
with metal reinforcing wires. Damage to
the tumble dryer can result if the metal
reinforcements come loose during drying.
• ●Do not tumble dry rubber, plastic articles
such as shower caps or babies waterproof
covers, polythene or paper.
• ●Do not tumble dry rubber backed articles,
clothes fitted with foam rubber pads,
pillows, galoshes and rubber coated tennis
shoes.
• ●Remove all objects from pockets such as
lighters and matches.
! WARNING: Never stop the dryer before
the end of the drying cycle unless all
items are quickly removed and spread
out so that the heat is dissipated.
Save energy and respect the environment
• Wring out all items to eliminate excess water before
tumble drying (if you use a washing machine first, select
a high spin cycle). Doing this will save time and energy
during drying.
• Always dry full loads - you save energy: single items or
small loads take longer to dry.
• Clean the filter after each use to contain energy
consumption costs (see Maintenance).
6
GB
Disconnecting the power supply
! Disconnect the dryer when not in use or
during cleaning and maintenance operations.
Cleaning the filter after each cycle
The filter is a fundamental component of the
dryer: its function is to collect lint and fluff that
form during drying.
Clean the filter once
drying is completed, by
rinsing it under running
water or cleaning it with a
vacuum cleaner. Should
the filter become clog-
ged, the flow of air inside
the dryer will be seriously
hampered: drying times
becomes longer and
more energy is consu-
med. Moreover, the dryer
may become damaged.
The filter is located in
front of the dryer seal
(see Picture).
Removing the filter:
1. Pull the filter’s plastic handle upwards (see
Picture).
2. Clean the fluff off the filter and replace it
correctly. Ensure that the filter is pushed fully
home.
! Do not use the dryer unless the filter has
been replaced in its holder.
Checking the drum after each cycle
Rotate the drum manually to remove smaller items (handker-
chiefs) that could have been left inside the dryer.
Cleaning the drum
! Avoid using abrasives, steel wool or stainless steel cleaning
agents to clean the drum. A coloured film may appear on the
stainless steel drum surface: it may be caused by a combina-
tion of water and/or cleaning agents such as wash-softeners.
This coloured film does not affect the dryer’s performance.
Emptying the water container after each
cycle
2
Remove the water container and
empty it into a sink or other
suitable drain outlet, then
replace it correctly.
Always check the water contai-
ner and empty it before starting
a new drying cycle.
-Failure to empty the water container may cause the
following:
- The dryer stops heating (thus the load may still be
damp at the end of the drying cycle).
- The “Empty water container” LED activates to show
that the water container is full.
Priming the Water Collection System
When your dryer is new, the Water Container will not
collect Water until the system is primed, this will take
1 or 2 drying cycles. Once primed it will collect Water
during every cycle.
Cleaning the Heat Pump Filter Unit
• Periodically (every 5 drying cycles) remove
Heat pump filter unit and clean any build up
of fluff from the surface of the filter by rinsing
it under running water or with your vacuum
cleaner.
We however recommend that you clean this
filter after every drying cycle to optimize the
dryers performance.
To remove Heat pump
filter unit:
1. Unplug the dryer and
open the door.
2. Remove the filter unit
by rotating the 4 clips
to the vertical position
then pulling the filter
unit towards you.
3. Separate the two
parts of the filter unit and
clean the surface of the
filter.
! Warning: The front of
the heat pump is made
from thin metal plates.
Take care that you do
not damage these or cut
yourself when cleaning,
removing or replacing
the filter unit.
4.Whenever you clean
the Heat pump filter
unit always clean any
build up of fluff from
the surface of the metal
plates. Carefully clean
this fluff off with a damp
cloth,sponge or vacuum
cleaner. Never use your
Fingers.
5. Assemble the two parts of the filter clean
the surface of the seals and replace with the
4 clips into the horizontal position, sure that
the catches have been secured.
Cleaning the tumble dryer
• The external metal, plastic and rubber parts can be clea-
ned with a damp cloth.
• Clean the front air intake grille regularly (every 6 months)
with a vacuum cleaner to remove any lint, fluff or dust
deposits. Furthermore, remove any lint deposits from the
front part of the condenser and from the filter area, using a
vacuum cleaner every so often.
! Do not use solvents or abrasives.
! Have the dryer checked regularly by authorised technical
personnel in order to ensure that the electrical and mechani-
cal parts work safely (see Assistance).
Care and maintenance
2
Water container
Heat pump
filter unit
Condenser cover
Catches
Filter
Handle
Air intake
Quick Tips
!Remember to clean your filter and Heat
Pump filter unit after each load.
! Remember to empty your water
container after each load.
! Doing this will keep your machine
working at its BEST!
GB
7
Disconnecting the power supply
! Disconnect the dryer when not in use or
during cleaning and maintenance operations.
Cleaning the filter after each cycle
The filter is a fundamental component of the
dryer: its function is to collect lint and fluff that
form during drying.
Clean the filter once
drying is completed, by
rinsing it under running
water or cleaning it with a
vacuum cleaner. Should
the filter become clog-
ged, the flow of air inside
the dryer will be seriously
hampered: drying times
becomes longer and
more energy is consu-
med. Moreover, the dryer
may become damaged.
The filter is located in
front of the dryer seal
(see Picture).
Removing the filter:
1. Pull the filter’s plastic handle upwards (see
Picture).
2. Clean the fluff off the filter and replace it
correctly. Ensure that the filter is pushed fully
home.
! Do not use the dryer unless the filter has
been replaced in its holder.
Checking the drum after each cycle
Rotate the drum manually to remove smaller items (handker-
chiefs) that could have been left inside the dryer.
Cleaning the drum
! Avoid using abrasives, steel wool or stainless steel cleaning
agents to clean the drum. A coloured film may appear on the
stainless steel drum surface: it may be caused by a combina-
tion of water and/or cleaning agents such as wash-softeners.
This coloured film does not affect the dryer’s performance.
Emptying the water container after each
cycle
2
Remove the water container and
empty it into a sink or other
suitable drain outlet, then
replace it correctly.
Always check the water contai-
ner and empty it before starting
a new drying cycle.
-Failure to empty the water container may cause the
following:
- The dryer stops heating (thus the load may still be
damp at the end of the drying cycle).
- The “Empty water container” LED activates to show
that the water container is full.
Priming the Water Collection System
When your dryer is new, the Water Container will not
collect Water until the system is primed, this will take
1 or 2 drying cycles. Once primed it will collect Water
during every cycle.
Cleaning the Heat Pump Filter Unit
• Periodically (every 5 drying cycles) remove
Heat pump filter unit and clean any build up
of fluff from the surface of the filter by rinsing
it under running water or with your vacuum
cleaner.
We however recommend that you clean this
filter after every drying cycle to optimize the
dryers performance.
To remove Heat pump
filter unit:
1. Unplug the dryer and
open the door.
2. Remove the filter unit
by rotating the 4 clips
to the vertical position
then pulling the filter
unit towards you.
3. Separate the two
parts of the filter unit and
clean the surface of the
filter.
! Warning: The front of
the heat pump is made
from thin metal plates.
Take care that you do
not damage these or cut
yourself when cleaning,
removing or replacing
the filter unit.
4.Whenever you clean
the Heat pump filter
unit always clean any
build up of fluff from
the surface of the metal
plates. Carefully clean
this fluff off with a damp
cloth,sponge or vacuum
cleaner. Never use your
Fingers.
5. Assemble the two parts of the filter clean
the surface of the seals and replace with the
4 clips into the horizontal position, sure that
the catches have been secured.
Cleaning the tumble dryer
• The external metal, plastic and rubber parts can be clea-
ned with a damp cloth.
• Clean the front air intake grille regularly (every 6 months)
with a vacuum cleaner to remove any lint, fluff or dust
deposits. Furthermore, remove any lint deposits from the
front part of the condenser and from the filter area, using a
vacuum cleaner every so often.
! Do not use solvents or abrasives.
! Have the dryer checked regularly by authorised technical
personnel in order to ensure that the electrical and mechani-
cal parts work safely (see Assistance).
Care and maintenance
2
Water container
Heat pump
filter unit
Condenser cover
Catches
Filter
Handle
Air intake
Quick Tips
!Remember to clean your filter and Heat
Pump filter unit after each load.
! Remember to empty your water
container after each load.
! Doing this will keep your machine
working at its BEST!
8
GB
On/Off
button
Start/Pause button
and indicator light
Programme
selection knob
Press
the door
Heat Pump
Filter Unit
(cover open)
Water container
Rating plate
Heat Pump Filter
Unit cover handle
(Pull here to open)
Filter
Air
intake
grille
Description of the
tumble dryer
Opening the door
Control panel
Features
Options
buttons and
indicator lights
Display
Delay start
button
Timed Drying
button
Empty water
container indicator light
Clean filter
indicator light
Clean
Heat
Pump Filter
indicator light
Cycle
phases
Timed
drying
icon
Delay
start icon
Model
& Serial
Numbers
Ajustable feet
(to level dryer)
GB
9
ON/OFF/Reset button
Pressing the button normally will cause the machine to switch on or off. If the button is pressed for 3 seconds while the dryer is in use,
the machine will switch off and the running cycle will reset.
Programme selection knob
Allows for setting the programme: turn until the indicator points towards the desired programme (see Starting and selecting a programme).
Options buttons
Allows selection of the options available for the selected programme. The respective indicator lights turn on when the option has been
selected (see Programmes and options).
START/PAUSE button and indicator light
When the green light flashes slowly, press the button to start the programme. When the cycle is under way, the indicator light re-
mains on. Press the button again to put the programme in the pause mode; the indicator light turns orange and starts flashing again.
Press the button again to resume the programme from the point it was interrupted (see Starting and selecting a programme).
Display
In section A, the selected “Timed drying” value is displayed; if the “Delay start” function was set, the time remaining to the start of the
selected programme will appear.
The duration of the selected programme is also displayed in this section.
In section B, the phase of the running programme is displayed:
Sun icon : Drying cycle
Fan icon : Cool tumble cycle
In section C, the maintenance indicator lights are displayed (Empty water container indicator light , Clean filter indicator light ,
Clean Heat pump filter unit indicator light ), see Indicator lights.
Indicator lights
The indicator lights provide important information. They indicate the following:
The “Empty water container” indicator light signals that the water container must be emptied.
If the water container fills during the course of the programme, the LED lights up. The dryer automatically starts a cold air cycle and
the START/PAUSE LED flashes orange. Press the START/PAUSE button to resume the cycle from the point it was interrupted.
In order to avoid this procedure, always empty the water container after using the tumble dryer (see Maintenance).
Before each programme, the “Clean filter” indicator light signals the fundamental importance of cleaning the filter before each load
(see Maintenance).
The “Clean Heat pump filter unit” indicator light indicates that you must clean the Heat pump filter every 5 cycles (however, we
recommend you clean it after each cycle).
C
B
A
10
GB
How to carry out a
drying cycle
Starting and selecting a programme
1. Plug the dryer into the power supply socket.
2. Select the programme according to the type of laundry (see Laundry).
3. Open the door, ensure that the filter is clean and securely placed and that the water container is empty and correctly slotted (see
Maintenance).
4. Load the machine, making sure that no piece of laundry gets between the door and the relative seal. Close the door.
5. Press the ON/OFF button to switch on the machine.
6. After consulting the programme chart and the indications for each type of fabric (see Laundry), turn the Programme selection
knob towards the programme corresponding to the type of laundry to be dried (see Programmes and options).
! Warning: If the position of the programme selection knob changes after pressing the START/PAUSE button, the selected program-
me will NOT be modified. To modify the programme, press the START/PAUSE button to put the programme in pause mode (the
indicator light flashes orange), then select a new programme and the relative options. Press the START/PAUSE button to start the
new programme.
7. Select the ”Timed Drying” function by pressing the timed drying button until the required time is dispayed (see Programmes and
options).
8. If necessary, set the time of the delayed start and any other options (see Programmes and options).
9. Press the ALARM button to sound a buzzer signalling the end of the programme.
10. Press the START/PAUSE button to start the drying cycle. The display will show the approximate time remaining.
Laundry can be checked while the drying programme runs and any garments already dry can be removed, while drying continues
for the remaining items. After closing the door, press the START/PAUSE button to resume machine operation.
11. The final COOL TUMBLE phase (i.e. the fabrics are cooled) activates during the last few minutes of the drying programme;
always allow this phase to terminate.
12. At the end of the drying cycle the display shows END.
The buzzer will beep 3 times to let you know that your programme is complete. (Note: If the SOUND option was selected the buzzer
beeps 3 times every 30 seconds for 5 minutes).
Open the door, remove the laundry then clean the filter and replace it. Empty the water container and put it back in its slot (see
Maintenance).
If the clothes are not removed at the end of the cycle the automatic Anti Craese action will, on those programmes with this feature,
continue to rotate the drum intermittently for up to 10 hours to minimise creasing. Opening the door or pressing the OFF button will
stop the Anti Crease action.
13. Disconnect the dryer from the power supply.
Automatic pre-post Anti Crease
This is an automatic function which provides an anti crease treatment both before and after the drying programme. By periodically
rotating the drum before the start of the drying cycle, when a delayed start is selected, the formation of creases is reduced. On
certain programmes the drum also rotates periodically at the end of the drying cycle on. This post crease care action continues until
either the door is opened or the OFF button is pressed.
Standby mode
This tumble dryer, in compliance with new energy saving regulations, is fitted with an automatic standby system which is enabled
after about 30 minutes if no activity is detected. Press and hold the ON/OFF button until the dryer reactivates.
GB
11
Programme
Max.
load
(kg)
Compatible options
Cycle
duration
Fast & Easy
The duration of the drying cycles can be checked on the display
3
.
1 Fast 45
1
Memo - Key Lock- Delay Timer.
2 Easy mix
3
Memo - Key Lock- Delay Timer.
3 Less Creased
3
Memo - Key Lock.
4 Cotton fast Iron
Max. Extra Care - Memo - Key Lock- Time Dry - Delay Timer.
5 Synthetic fast Iron
4 Memo - Key Lock- Time Dry - Delay Timer.
Essentials
6 Standard Cotton
2
Max. Extra Care - Energy Saver
1
- Memo - Key Lock- Time Dry - Delay Timer.
7 Cotton ready to wear
Max. Memo - Key Lock- Time Dry - Delay Timer.
8 Synthetics
4 Energy Saver
1
- Memo - Key Lock- Time Dry - Delay Timer.
9 Jeans
3
Memo - Key Lock- Delay Timer.
Special Care
10 Baby&Delicates
2 Memo - Key Lock- Time Dry - Delay Timer.
11 Wool
1 Memo - Key Lock.
12 Duvet
1,5 Memo - Key Lock- Delay Timer.
13 Gym kit
4 Memo - Key Lock- Delay Timer.
14 Special Shoes
1 pair Memo - Key Lock.
Post Dry
15
Crease Relax - Memo - Key Lock.
16
Freshen UP 2,5 Memo - Key Lock.
NOTES: 1 with this option the maximum load size is modifi ed. Refer to the option description. 2 Standard Cotton is the most effi cient program
in terms of energy consumption (EU 392/2012). 3 The duration of these programs will depend on the size of the load, types of textiles, the spin
speed used in your washer and any extra options selected.
Programmes and options
Programme chart
Special/Sport/Partial Programmes
Fast 45’
45
’
This is a quick timed programme, ideal for drying garments spun at high speed in the washing machine, for example shirts used in a
working week.
Easy Mix
This programme is ideal for drying cotton and synthetic fabrics together.
Less Creased
A cycle for synthetic and mixed textiles making lengthy ironing unnecessary.
Shake the pieces of clothing before introducing them into the dryer. Remove the pieces of clothing immediately at the end of the
programme and hang them
Standard Cotton: Dries your items to a dryness level that allows you to put your clothes away straight from the dryer.
Cotton Ready to Wear: Dries your items to the maximum possible dryness level. Even drier than Standard Cotton.
Jeans
●This is a programme for jeans made from denim cotton. Before drying your jeans turn the front pockets inside out.
●Do not mix dark and light coloured items.
It can also be used on other garments made from the same material, such as jackets.
Loads dried using this programme are usually ready to wear, the edges or seams may be slightly damp. If this is the case, try turning
the jeans inside out and running the programme again for a short period.
! We do not recommend that you use this programme if your jeans have elastic waist bands, studs or embroidery.
12
GB
12
Baby&Delicates
A programme appropriately designed to dry clothing and linen of new-born babies (cotton and chenille) and delicate clothes. Do not
dry articles which have plastic covering.
Wool Programme
This programme is specific for items that withstand tumble drying and are labelled with the symbol. It is suitable for loads of up to
1 kg (about 3 jerseys). We recommend turning the garments inside out before drying them. Garments dried with this programme are
usually ready to be worn, although the edges of heavier garments may be slightly damp. Leave them to dry naturally, as an additio-
nal drying process may damage them.
Unlike other materials, the shrinking process in wool is irreversible, i.e. the garment does not resume its original dimension and sha-
pe. This programme is not suited for acrylic items.
Duvet
A cycle intended to dry down jackets, giving their natural softness back (2 jackets).
Gym Kit
A cycle designed to dry complete gym kits for all the family (shorts, top, t-shirts and towels).
Special Shoes Programme
This programme is specific for drying sports shoes. The shoes must have been previously washed and spun at a minimum spin
speed of 400 revolutions.
A specific shoe rack is provided and must be used, otherwise the dryer will be damaged if shoes are dried in the drum. Remove the
filter from its holder on the front part of the dryer and position the shoe rack.
Place shoelaces inside the shoes then load with the tips of the shoes facing downwards and the soles frontwards.
Drying times vary according to the shape and type of the shoe. If the shoes are not completely dry at the end of the programme,
restart the programme.
! Do not dry shoes that have gel or flashing lights inside them. Only dry shoes made of synthetic material or rope. Once the pro-
gramme ends, remove the shoe rack and replace the filter into its holder.
Crease Relax
A short 10-minute programme that relaxes the garment’s fibres in order to facilitate ironing and folding.
This programme is particularly recommended for cotton or mixed cotton fabrics.
For optimal results, do not overload the drum (the following values refer to the weight of dry garments):
Fabric: maximum load
Cotton and mixed cotton: 2.5 kg
Synthetic garments: 2 kg
Jeans: 2 kg
Empty the dryer as soon as the programme ends; hang, fold or iron garments then place them in the wardrobe. If this is not possi-
ble, repeat the programme.
As this is not a drying programme, it is not to be used for garments that are still wet.
The effect produced by the programme varies according to the characteristics of the each fabric: fabrics such as acrylic fibres or
Tencel
®
do not give the same results as traditional fibres (e.g. cotton).
Freshen Up
A short programme suitable for refreshing fibres and garments. It lasts about 20 minutes.
! As this is not a drying programme, it is not to be used for garments that are still wet.
● It can be used on any load size but is more effective on smaller loads.
Options
The options allow for customising the selected programme according to one’s own needs.
Timed drying
After selecting a programme, press the “Timed drying” button to enter a drying time. Every time this button is pressed, the duration of
the selected drying cycle appears on the display. When pressed the first time, the highest allowed value for the selected cycle appears
on the display. When pressed each of the following times, the set time is reduced until OFF appears.
The buzzer will activate if the timed drying option is not available.
GB
13
Delay Timer
The start of some programmes (see Programmes and options) may be delayed up to 24 hours. Before selecting a programme with
a delayed start make sure that the water bottle is empty and the filter is clean. The drum will rotate occasionally before the drying
programme starts to prevent the formation of creases.
Extra Care
This is a special option designed to gentle dry delicate clothes.
Press this button to select the low temperature setting; the light next to the button will switch on. Activating this option will increase
the duration of the cycles.
Energy Saver
An option designed to optimise the results when drying small loads (cotton loaded to a max. of 2 kgs. and synthetic
load to a max. of 1 kg.) thereby minimising consumption and drying times.
Memo
This option allows you to store your cycle selection along with any associated options and to easily use a previously stored cycle.
Delayed start options cannot be stored.
•Press and hold the button MEMO for 3 second to store a cycle. You can press this button when the desired cycle and associa-
ted options have been selected either before the cycle has started or during the drying cycle. When you press and hold the Memo
button the LED flashes as well as the time on the display and after 3 second a beep will confirm that the details have been stored.
•To recall the stored cycle simply turn on the dryer, press the memo button and then start the cycle. It is possible to change any of
the options in the normal way. Every 2 minutes the stored cycle number will appear on the display. If no cycle has been stored you
will hear a beep when the Memo button is pressed.
•A stored programme can be overwritten with a new programme just by repeating the steps outlined above.
Key Lock
Keep this button pressed for a few seconds after choosing the programme and the desired options. When the warning
light is on, the other buttons and the knob are deactivated. To deactivate the block keep the button pressed and the
warning light goes off. The ON/OFF button switches off the machine even if the function lock button is active.
Not all options are available on all programmes (see Programmes and options).
Opening the door
If the door is opened (or the START/PAUSE button is pressed) while a programme is running, the dryer stops and the following may
occur:
• The START/PAUSE button flashes orange.
• When a delayed start is running, the delay countdown continues. It is necessary to press the START/PAUSE button to resume
the “Delay start” programme. The “Delay start” indicator light flashes and the display visualises the time remaining to the start of the
selected programme.
• It is necessary to press the START/PAUSE button to resume the programme. The progress indicator lights signal the running pha-
se and the START/PAUSE indicator light stops flashing and turns green.
• During the post anti-crease phase, the programme ends. Pressing the START/PAUSE button reactivates a new programme from
the beginning.
• By turning the Programme selection knob, a new programme is selected and the START/PAUSE indicator light flashes green. This
procedure can be used to select the COOL drying programme to cool garments if they are judged to be dry enough.
Press the START/PAUSE button to start the new programme.
Heat Pump Protection System
The heat pump sytem has a compressor protection feature, that operates if you open the door or there is a power disruption or you
turn off the dryer. This system will prevent the heat pump compressor from starting for 5 minutes after the door is closed and the
programme started.
Note: If you have a power cut, switch off the power or remove the plug. When power is restored, plug in the machine, press and
hold the ON/OFF button until the dryer reactivates, then press Start/Pause button.
14
GB
Sorting laundry
• Check the symbols on the care labels of the various gar-
ments to verify whether the garments can be safely tumble
dried.
• Sort laundry according to the type of fabric.
• Empty all pockets and check for loose buttons.
• Close zips and hooks and fasten belts and strings without
tightening them.
• Wring out garments to remove the maximum amount of
water possible.
!
Do not load the dryer when garments are dripping wet.
Maximum load sizes
Do not overload the drum.
The following values indicate the weight of dry garments:
Natural fibres: maximum kg
Synthetic fibres: maximum kg
! Do not overload the dryer as this may result is reduced
drying performance.
Care labels
Always check the care labels, especially when placing
garments in the tumble dryer for the first time. Below are the
most commonly used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
Drying times
Drying times are approximate and may vary depending on
the following:
• Amount of water retained by items after the spin cycle:
towels and delicate items retain a lot of water.
• Fabrics: items of the same fabric, but with different texture
and thickness may have different drying times.
• Amount of laundry: single items and small loads may take
longer to dry.
• Drying: if items are to be ironed, they can be removed
from the dryer while still slightly damp. Items that require
complete drying can be left longer.
• Heat setting.
• Temperature of the room: the lower the temperature of the
room, the longer it will take for the dryer to dry clothing.
• Bulk: certain bulky items require special care during the
drying process. We suggest removing these items and
replacing them in the dryer once they have been shaken
out: repeat this procedure several times during the course
of the drying cycle.
! Do not over-dry items.
All fabrics contain natural dampness which helps to keep
them soft and fluffy.
The drying times provided refer to the automatic Cupboard
dry programmes.
The Timed drying settings are also indicated to enable you
to select the most suitable timed option.
The weight refers to dry items.
Laundry
7
4
GB
15
Troubleshooting
If you feel that the dryer is not working properly, consult the following troubleshooting suggestions before contacting the
Technical Assistance Centre
(see Assistance).
The dryer does not start.
• The plug has not been inserted far enough into the socket to make contact.
• There has been a power cut.
• The fuse has blown. Try connecting another appliance to the same socket.
• If an extension cord is used, try connecting the dryer plug directly into the socket.
• The door has not been closed properly.
• The programme has not been set correctly (see How to carry out a drying cycle).
• The START/PAUSE button has not been pressed (see How to carry out a drying cycle).
• On machines equipped with “Locked” function, check the option is not enabled (see Programmes and options).
The drying cycle does not start.
• A delayed start time has been set (see Programmes and options).
• The START/PAUSE button has been pressed; a short delay follows before the dryer starts running. Wait for the drying cycle to
start; do not press the START/PAUSE button otherwise the dryer switches to the pause mode and the drying cycle will not start.
Drying times are too long.
• The filter has not been cleaned (see Maintenance).
• The water container must be emptied? The “Empty water container” indicator light flashes and the message appears “H2O”
(see Maintenance).
• The Heat Pump Filter needs cleaning (see Maintenance).
• The heat setting is not suited to the type of fabric to be dried (see Programmes and options).
• An incorrect drying time was selected for the type of load (see Laundry).
• The items are too wet (see Laundry).
• The air intake grille are clogged up (see “Installation” and “Care and Maintenance”).
• The dryer is overloaded (see Laundry).
The “Empty water container” indicator light flashes, but the dryer has been running for a short time.
• The water container was probably not emptied before starting the programme. Do not wait for the signal for emptying the
water container, but always check and empty it before starting a new drying programme (see Description of the tumble dryer).
The “Empty water container” indicator light is on but the water container is not full.
• It is normal: the “Empty water container” indicator light flashes when the water container is full. If the indicator light is on but is
not flashing, it is just a reminder to empty the container (see Description of the tumble dryer).
The programme is finished but the items are damper than expected.
! For safety reasons, the dryer programmes last a maximum of 5 hours. If an automatic programme has not detected the final
dampness level required in this interval, the dryer completes the programme and stops. Check the above points and repeat
the programme; if the items are still damp, contact the Technical Assistance Centre (see Assistance).
The code “F” appears on the display followed by one or two numbers, the options indicator lights and the
pause indicator light flash.
• If the display shows a fault, switch the appliance off and unplug it, then clean the filter and the Heat Pump Filter unit (see
Maintenance). Reinsert the plug, switch the appliance on and start another programme. If the display still visualises a fault,
contact the Technical Assistance Centre (see Assistance). If the display still visualises other numbers, mark the code and
contact the Technical Assistance Centre (see Assistance).
“dOn” briefly appears on the display every 6 seconds.
• The appliance is in “Demo” mode. Press the ON/OFF and START/PAUSE buttons and keep them pressed for 3 seconds. The
display visualises “dOn” for 3 seconds, then the dryer starts functioning normally.
The “Remaining time” indicator changes during the drying cycle.
• The remaining time is constantly monitored during the drying cycle and is updated to show the best forecast. It is normal for
the displayed time to increase during the cycle.
The dryer is noisy during the first few minutes of operation.
• This is normal, especially if the dryer has not been used for a long time. If the noise persists during the entire cycle, contact
the Technical Assistance Centre.
The lights on the dryer control panel are off although the dryer is switched on.
• The dryer has gone into standby mode to save power. This occurs if you have left the dryer on or have had a power cut. It
occurs after 30 minutes:
- if you leave the dryer without starting a programme;
- after your drying programme has finished.
Press the On/Off button and the lights will come on again.
16
GB
Réparation
Informations pour le recyclage et la mise au rebut
Dans le cadre de notre engagement envers la protection de l’environnement, nous nous réservons le droit d’utiliser des pièces
recyclées de qualité afin de réduire les coûts pour notre clientèle et de limiter les gaspillages de matières premières.
• Mise au rebut du matériel d’emballage : respectez les réglementations locales, de manière à ce que l’emballage puisse être
recyclé.
• Pour éviter que des enfants se blessent, ôtez la porte et la prise et puis coupez le câble secteur au ras de l’appareil. Jetez ces
pièces séparément de sorte que l’appareil ne puisse plus être branché sur une prise de secteur.
Mise au rebut des électroménagers usagés
La directive européenne 2012/19/CE sur les déchets d’équipements électriques et électroniques (DEEE), prévoit que les
électroménagers ne peuvent pas être traités comme des déchets solides urbains normaux. Les appareils usagés doivent faire
l’objet d’une collecte séparée pour optimiser le taux de récupération et de recyclage des matériaux qui les composent et
empêcher tout danger pour la santé et pour l’environnement.
Ce sèche-linge utilise une pompe à chaleur étanche contenant des gaz fluorés qu’il faut récupérer et éliminer. Le symbole de
la poubelle barrée est appliqué sur tous les produits pour rappeler qufils font lfobjet dfune collecte sélective. Pour tout autre renseigne-
ment sur la collecte des électroménagers usés, prière de sfadresser au service public préposé ou au vendeur.
Cet appareil a été conçu, construit et mis sur le marché conformément aux normes
prévues dans les directives européennes suivantes:
- LVD 2014/35/EU, EMC 2014/30/EU et RoHS 2011/65/EU.
Système à pompe à chaleur
Ce sèche-linge est équipé d’un système à pompe à chaleur
pour sécher votre linge. Pour son fonctionnement, la pompe
à chaleur utilise des gaz à effet serre (gaz fluorés) qui sont
visés par le protocole de Kyoto. Les gaz F sont enfermés
dans une unité étanche. Cette unité étanche contient kg
de gaz R134a F qui agit comme réfrigérant.
GWP = 1430 (0.4 t C02). Si cette unité est abîmée, il
faut la remplacer par une neuve. Pour de plus amples
renseignements, contacter le centre d’assistance le plus
proche. Remarque : Les gaz enfermés dans une unité
étanche ne sont pas nocifs pour la santé mais, s’ils
s’échappent, ils ont un impact sur le réchauffement global.
Avant d’appeler un réparateur :
• Parcourez les pistes de dépannage afin de vérifier si vous
pouvez régler le problème par vous-même (voir Dépannage).
• Si ce n’est pas le cas, mettez l’appareil hors tension et
prenez contact avec le réparateur le plus proche.
Quels sont les éléments dont le réparateur a besoin:
• Nom, adresse et code postal ;
• numéro de téléphone ;
• type de problème ;
• date d’achat ;
• modèle (Mod.) ;
• numéro de série (S/N).
Vous trouverez ces informations sur l’étiquette placée à
l’intérieur du hublot.
Pièces détachées
Ce sèche-linge est une machine complexe. En tentant de le
réparer par vous-même ou en demandant à une personne
non agréée d’effectuer une réparation, vous risquez de vous
blesser et d’endommager la machine. De plus, la garantie
risque de ne plus être valable. Appelez un technicien agréé
si vous rencontrez des problèmes lors de l’utilisation de
la machine. Toute personne non qualifiée qui effectue une
opération d’assistance ou une réparation quelconque qui
cause l’endommagement de la pompe à chaleur enfermée
commet une infraction.
0,29
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Hotpoint EDPE 745 A2 ECO EU Mode d'emploi
- Catégorie
- Sèche-linge
- Taper
- Mode d'emploi
dans d''autres langues
Autres documents
-
Indesit IDVA 835 (EU) Mode d'emploi
-
-
-
Whirlpool IDVA 835 (EU) Mode d'emploi
-
-
-
-
-
Indesit IDCL G5 B H Le manuel du propriétaire