Swann Safety Camera Kit Wireless Camera & Receiver Guide d'installation

Marque: Swann

Modèle: Safety Camera Kit Wireless Camera & Receiver

Taper: Guide d'installation

English

If this device does not work when you first plug it

in, do not take it back to the store.

Safety Camera Kit

Wireless Camera & Receiver

Contact the Swann Helpdesk using our fast e-mail service

[email protected] or call us on one of the Toll-Free

numbers shown on the back cover of this booklet.

Installation Guide

Swann Communications warrants this product against defects in workmanship and material for

a period of one (1) year from it’s original purchase date. You must present your receipt as

proof of date of purchase for warranty validation. Any unit which proves defective during the

stated period will be repaired without charge for parts or labour or replaced at the sole

discretion of Swann. The repair or replacement will be warranted for either ninety days or the

remainder of the original one year warranty period, whichever is longer. The end user is

responsible for all freight charges incurred to send the to Swann’s repair centres.

shipping from and to any country

other than the country of origin. The warranty does not cover any incidental, accidental or

consequential damages arising from the use of or the inability to use this . Any costs

associated with the fitting or removal of this product by a tradesman or other person or any

other costs associated with its use are the responsibility of the end user. This warranty applies

to the original purchaser of the only and is not transferrable to any third party.

Unauthorised end user or third party modifications to any component or evidence of misuse or

abuse of the device will render all warranties void.

product The

end user is responsible for all shipping costs incurred when

product

Help Desk / Support Details

Warranty Information

www.swannsecurity.com

Swann Technical Support

All Countries E-mail: [email protected]

Telephone Helpdesk

See http://www.worldtimeserver.com for information on different time zones

and the time in Melbourne Australia compare to your local time.

UNITED STATES toll free

1-800-627-2799

1-877-274-3695

(Su, 2pm-10pm US PT)

(M-Th, 6am-10pm US PT)

(F 6am-2pm US PT)

USA Exchange & Repairs

562-777-2551

(M-F, 9am-5pm US PT)

AUSTRALIA toll free

1300 138 324

(M 9am-5pm AUS ET)

(Tu-F 1am-5pm AUS ET)

(Sa 1am-9am AUS ET)

New Zealand toll free

0800 479 266

International

+61 3 8412 4610

Swann Communications U.S.A. Inc.

10612 Shoemaker Avenue, Bldg A

Santa Fe Springs, CA 90670 USA

1-800-627-2799

WARNING: IMPORTANT NOTICE ABOUT CORRECT USE OF POWER ADAPTER

The correct orientation

for the enclosed power

adapter is in a vertical

or floor mount position

L’orientation correcte pour

L’adapteur secteur fourni

est dans une position

verticale ou plancher-

monte.

La orientacion correcta para

el adaptador electrico incluido

es en posicion vertical o instalado

en el suelo.

FCC INFORMATION

This device complies with Part15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may cause harmful interference,

(2) This device must accept any interference received, including interference that may cause

undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

The Swann Safety Camera Kit allows you to wirelessly transmit pictures and

sound with ease. As the radio waves it uses have a frequency of 2.4GHz, they

can be received within a radius of up to 160 The Safety

Camera Kit Receiver works with other Swann wireless cameras to allow you to

have the option of using different frequencies for different locations and conditions

to ensure that you have the best possible image quality for your situation.

ft/50m in open line of sight.

Please note: The Swann Safety Camera Kit broadcasts video in the public

domain. The video signal is not encrypted and could potentially be viewed by

anyone with a similar 2.4GHz receiver unit. Please keep this in mind when

positioning and using any wireless camera equipment.

• Safety Camera with built in 2.4GHz Transmitter and Stand

• 4 channel 2.4GHz Receiver

• Antenna for Receiver

• 2 x Mains Power Adaptor (1 for use with Camera and 1 for Receiver)

• RCA A/V Cable

• Manual & Accessories

• Focus Tool

• Dip Switch Tool

If any of these items are missing, please contact your retailer.

Technical SpecificationsIntroduction

Package Contents

NOTE:

All jurisdictions have specific laws and regulations relating to the use of cameras.

Before using any camera for any purpose, it is the buyer’s responsibility to be

aware of all applicable laws and regulations that prohibit or limit the use of

cameras and to comply with the applicable laws and regulations.

The legality of watching people other than yourself changes from country to

country and even state to state. Contact your local government's privacy

information body or your local Police for more information on what if any

restrictions you may face.

Receiver

Frequency: 4 Channels in 2.4 Ghz frequency band

Video input/output: 1V p - p / 75 ohm

Audio input / output: 1V / 10kW

Audio Bandwidth: 50 - 17000 Hz

Operating Power: 12V DC

Size: 4.7”x3.5”x1” (120 x 90 x 25mm)

*The Safety Camera Kit uses following frequencies for the 4 channels:

Channel 1( 2414MHz), Channel 2 (2432MHz), Channel 3 (2450MHz)

and Channel 4 (2468MHz).

Safety Camera

Sensor: 1/3” Colour CMOS

Horizontal Resolution: 380 TV lines

Auto Electronic Exposure: 1/60 - 1/15000 sec.

Minimum Illumination: 1 Lux @ f1.2

Signal to Noise Ratio: >48dB

Board Lens: / ” ; 5.6mm

View Angle: 60 degrees

Video System: PAL 50Hz (Australia, UK/Europe),

NTSC 60Hz (USA and Canada)

Automatic Exposure / Gain / White balance/IR LED activation

Available Channels: 4 Channels in 2.4Ghz frequency band*

RF Output Power: FCC, CE and C-tick compliant

Operating Power: 12V DC

Size: 1.1”x1.2”x1.1” (28x30x28mm)

Antenna: Omni-directional

Transmitting Range: Up to 160ft ~ 50M line of sight

Weight: ¾oz ~ 20 grams

Operating Temperature: -10° - 50°C (14° - 122°F)

WARNING - IMPORTANT SAFETY INSTRUCTIONS

To reduce fire or shock hazard do not expose the unit or adapters to rain or moisture

Do not handle damaged or leaking Lithium-Ion batteries

Do not use if any of the terminals or wires are exposed

Use only the power adapter that is included in this pack in an upright or vertical position

Any modifications not approved by Swann Communications PTY LTD. may void the user’s

ability to operate this product

The Camera features an omni-directional antenna which is most effective when used

in the UPRIGHT position.

1) Connect both the Camera and the Receiver to their respective power adaptors.

2) Connect the Receiver to the equipment you wish to view the camera on (monitor,

AV TV, VCR, DVR etc) using the supplied RCA A/V-cable. If you have an A/V TV

with RCA sockets you will need to switch the TV to the AV channel to view the

camera. To connect the Receiver to your VCR, you will need to turn the VCR to

the AV Input selection and turn your TV onto the channel you would normally use

to view a tape or movie on your VCR. The AV channel may be activated by a

button on your remote that is marked with this symbol , or L1 or L2 or

possibly AV, AV1 or AV2. Check the manual of your TV or VCR for more

information on using its AV inputs.

3) After connecting both the Camera and the Receiver make sure the receiver is

switched to the same channel as the camera. Press the Channel Select button

on the receiver until the LED is lit. Obtain the best picture by adjusting the

position of the Camera and Receiver unit to suit. Try slightly different locations of

either unit for optimum results.

Camera with Stand and Hood

Camera Power Adaptor

Poor Picture: Realign antennas until image quality improves, slightly adjust the

position of the Camera or Receiver.

Lines only: no clear picture: Check to confirm there is no microwave oven or other

2.4GHz equipment ie; Cordless Telephones, Wireless Baby

Monitors, Wireless LAN equipment etc . Make sure the Receiver is on the correct

channel for the particular camera.

Picture ghosting or interference:

No picture: check the receiver to confirm it is powered and make sure the A/V

connection of the Receiver is not plugged into the Audio Out socket. Make sure the

Receiver is on the correct channel. Check to ensure the camera is plugged in and has

power. Check that the channel on the receiver is the set to the same as the camera

you wish to view.

Red haze over picture: In some cases where the sun shines into the front of the

camera a faint red glow can be seen. Move the camera to a shaded location, or fit a

hood to stop sunlight entering the camera lens directly.

Foreground is dark while background is too bright: If the camera is looking from a

dark area towards a light area in some cases the automatic exposure can find it

difficult to balance the image correctly. Change the location of the camera so that the

point of greatest interest has the largest area of the image (if you want to see the

bright area, move the camera so that almost all of the screen shows this area. If you

want to see the darker area, move the camera so that most of the image shows this

area)

Change the location of the Camera to allow the

minimum of solid objects such as walls between it and the receiver as illustrated at the

bottom of the page. Try changing to one of the other channels using the instructions on

the previous page and check the signal quality again.

operating close by

Some home appliances such as Wireless LANs,

2.4GHz portable telephones and Microwave ovens operate on or near the 2.4GHz

frequency. If you receive interference from such an appliance, try moving the Camera

or Receiver to location further away from the appliance or in the event of interference

from a Wireless LAN device, try changing the Wireless LAN to a different channel to

improve the signal quality.

Monitor or TV

Signal passes

through 3 walls

Signal passes

through 3 walls

Signal only passes

through 2 walls!

Signal only passes

through 2 walls!

Your home or officeYour home or office

Troubleshooting, hints and tips Setting up your system

DVR or MONITOR

With RCA Sockets

I E

D O

Receiver

Power Adaptor

CH4

Receiver

RCA A/V Cable

The Safety Camera can be switched to any of four frequencies to assist in avoiding

interference. Please see the illustration for frequency settings. On the power

cable connected to the camera find the small flap covering the two dip switches. Move

the switches using the dip switch tool, or a pin according to the images below to set

the correct channel. The LEDs on the receiver indicate which channel is currently

selected.

below

Channel & Frequency

By changing these switch settings, the frequency that the

Camera transmits on changes. Once you have set the channel

on the Camera, select the same channel on the receiver. If you

experience interference try a different channel.

Do not set two Cameras to the same channel or they

will interfere with each other.

Receiver Features

Camera features Changing the channel on the camera

Receiver & Remote Control features

DC Power Socket

A/V Output

Channel LEDs

Channel selector

Button

External Antenna

DC Power Socket

ONON

1 21 2

Ch1 - 2414MHz

1 = OFF

2 = OFF

Ch3 - 2450MHz

1 = OFF

2 = ON

Ch2 - 2432MHz

1 = ON

2 = OFF

Ch4 - 2468MHz

1 = ON

2 = ON

DC Power Socket

Channel Switch

(see “Changing the

channel on the camera”)

Focus Tool

(Insert and turn

to focus camera)

Microphone

External Antenna

Channel Lockout Switch

Channel lockout switch on the receiver

This receiver is equipped with Lockout and Loop features.

The switches are numbered 1,2,3,4 representing 4 camera

channels. When the switch is in the UP position the camera

channel is OFF. When the switching between channels the

receiver will automatically skip channel set to OFF.

Loop mode allows you to see all active camera channels

set to ON by cycling through channels every few seconds.

This feature is useful for monitoring cameras or VCR

recording. Move the L switch to ON to cycle active

channels.

(See next page for details)

Use the included

Dip Switch tool to

change the

camera channel

Use the included

Dip Switch tool to

change the

camera channel

The Safety Camera can be switched to any of four frequencies to assist in avoiding

interference. Please see the illustration for frequency settings. On the power

cable connected to the camera find the small flap covering the two dip switches. Move

the switches using the dip switch tool, or a pin according to the images below to set

the correct channel. The LEDs on the receiver indicate which channel is currently

selected.

below

Channel & Frequency

By changing these switch settings, the frequency that the

Camera transmits on changes. Once you have set the channel

on the Camera, select the same channel on the receiver. If you

experience interference try a different channel.

Do not set two Cameras to the same channel or they

will interfere with each other.

Receiver Features

Camera features Changing the channel on the camera

Receiver & Remote Control features

DC Power Socket

A/V Output

Channel LEDs

Channel selector

Button

External Antenna

DC Power Socket

ONON

1 21 2

Ch1 - 2414MHz

1 = OFF

2 = OFF

Ch3 - 2450MHz

1 = OFF

2 = ON

Ch2 - 2432MHz

1 = ON

2 = OFF

Ch4 - 2468MHz

1 = ON

2 = ON

DC Power Socket

Channel Switch

(see “Changing the

channel on the camera”)

Focus Tool

(Insert and turn

to focus camera)

Microphone

External Antenna

Channel Lockout Switch

Channel lockout switch on the receiver

This receiver is equipped with Lockout and Loop features.

The switches are numbered 1,2,3,4 representing 4 camera

channels. When the switch is in the UP position the camera

channel is OFF. When the switching between channels the

receiver will automatically skip channel set to OFF.

Loop mode allows you to see all active camera channels

set to ON by cycling through channels every few seconds.

This feature is useful for monitoring cameras or VCR

recording. Move the L switch to ON to cycle active

channels.

(See next page for details)

Use the included

Dip Switch tool to

change the

camera channel

Use the included

Dip Switch tool to

change the

camera channel