Samsung LN32A650A1F Manuel utilisateur

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG

customer care center.

Comment contacter Samsung dans le monde

Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez contacter le Service

Consommateurs Samsung.

Country

Customer Care Center

Web Site Address

CANADA 1-800-SAMSUNG(726-7864) www.samsung.com/ca

Samsung Electronics Canada Inc., Customer

Service 55 Standish Court Mississauga,

Ontario L5R 4B2 Canada

Samsung Electronique Canada Inc.,

Service à la Clientèle 55 Standish Court

Mississauga, Ontario L5R 4B2 Canada

U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com

Samsung Electronics America, Inc.

105 Challenger Road

Ridgefield Park, NJ 07660-0511

LCD TV

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at

www.samsung.com/global/register

Model Serial No.

BN68-01599C-01

BN68-01599C-01L02-Cover.indd 1 2008-04-06 ¿ÀÀü 10:38:01

Precautions When Displaying a Still Image

A still image may cause permanent damage to the TV screen

Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention. This image

retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the

screen when displaying a still image.

Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders displayed on the left,

right and center of the screen caused by the difference of light emission on the screen.

Playing a DVD or a game console may cause a similar effect to the screen.

Damages caused by the above effect are not covered by the Warranty.

Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images.

To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

•

Important Warranty Information Regarding Television Format Viewing

Wide screen format LCD Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format

full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to ll the screen if

your model offers this feature and the images are constantly moving. Displaying stationary graphics and images on screen, such as the dark

sidebars on nonexpanded standard format television video and programming, should be limited to no more than 5% of the total television

viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites or computer

graphics and patterns, should be limited as described above for all televisions. Displaying stationary images that exceed the above guidelines

can cause uneven aging of LCD Displays that leave subtle, but permanent burned-in ghost images in the LCD picture. To avoid this, vary the

programming and images, and primarily display full screen moving images, not stationary patterns or dark bars.

On LCD models that offer picture sizing features, use these controls to view different formats as a full screen picture.

Be careful in the selection and duration of television formats used for viewing. Uneven LCD aging as a result of format selection and use, as

well as burned-in images, are not covered by your Samsung limited warranty.

U.S.A Only

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. In particular,

this product is licensed under the following US patents: 5,991,715, 5,740,317, 4,972,484, 5,214,678, 5,323,396, 5,539,829, 5,606,618,

5,530,655, 5,777,992, 6,289,308, 5,610,985, 5,481,643, 5,544,247, 5,960,037, 6,023,490, 5,878,080, and under US Published Patent

Application No. 2001-44713-A1.

This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial

use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit

or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers

the use of this product unit to encode and/or decode audio les conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are

granted under this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

Other countries

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is

limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license

does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process

conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers the use of

this product unit to encode and/or decode audio les conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under

this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY STATEMENT

Subject to the requirements, conditions, exclusions and limitations of the original Limited Warranty supplied with Samsung Electronics

(SAMSUNG) products, and the requirements, conditions, exclusions and limitations contained herein, SAMSUNG will additionally provide

Warranty Repair Service in the United States on SAMSUNG products purchased in Canada, and in Canada on SAMSUNG products

purchased in the United States, for the warranty period originally specied, and to the Original Purchaser only.

The above described warranty repairs must be performed by a SAMSUNG Authorized Service Center. Along with this Statement, the

Original Limited Warranty Statement and a dated Bill of Sale as Proof of Purchase must be presented to the Service Center. Transportation

to and from the Service Center is the responsibility of the purchaser.

Conditions covered are limited only to manufacturing defects in material or workmanship, and only those encountered in normal use of the

product.

Excluded, but not limited to, are any originally specied provisions for, in-home or on-site services, minimum or maximum repair times,

exchanges or replacements, accessories, options, upgrades, or consumables.

For the location of a SAMSUNG Authorized Service Center, please call toll-free:

In the United States : 1-800-SAMSUNG (1-800-726-7864) In Canada : 1-800-SAMSUNG

See the warranty card for more information on warranty terms.

➣

BN68-01599A-Eng.indb 1 2008-03-21 ¿ÀÈÄ 1:31:57

General Information

List of Features ..................................................................2

Accessories .......................................................................2

Viewing the Control Panel .................................................3

Viewing the Connection Panel ...........................................4

Remote Control .................................................................5

Installing Batteries in the Remote Control .........................6

Connections

Connecting VHF and UHF Antennas .................................6

Connecting Cable TV ........................................................7

Connecting a DVD Player or Cable Box/

Satellite receiver (Set-Top Box) via HDMI .........................8

Connecting a DVD Player or Cable Box/

Satellite receiver (Set-Top Box) via DVI ............................8

Connecting a DVD Player or Cable Box/

Satellite receiver (Set-Top Box) via Component cables ....9

Connecting a Camcorder ...................................................9

Connecting a VCR ...........................................................10

Connecting a Digital Audio System .................................11

Connecting an Amplier/DVD Home Theater ..................11

Connecting a PC .............................................................12

Operation

Turning the TV On and Off ..............................................13

Plug & Play Feature .........................................................13

Changing Channels .........................................................15

Adjusting the Volume .......................................................15

Viewing the Display .........................................................16

Viewing the Menus ..........................................................16

Using the Remote Control Backlight Buttons .................16

Using the TOOLS Button .................................................17

Memorizing the Channels ................................................17

To Select the Source .......................................................19

To Edit the Input Source Name ........................................19

Picture Control

Changing the Picture Standard .......................................20

Customizing the Picture Settings .....................................20

Adjusting the Detailed Settings ........................................21

Resetting the Picture Settings to the Factory Defaults ....24

Conguring Picture Options .............................................25

Viewing Picture-in-Picture ...............................................29

Sound Control

Changing the Sound Standard ........................................31

Customizing the Sound ...................................................31

Setting the TruSurround XT .............................................32

Choosing Preferred Language ........................................33

Choosing a Multi-Channel Sound (MTS) track ................33

Automatic Volume Control ...............................................34

Setting the TV Speakers On/Off ......................................34

Listening to the Sound of the Sub (PIP) Picture ..............35

Resetting the Sound Settings to the Factory Defaults .....35

Connecting Headphones (Sold separately) .....................35

Channel Control

Managing Channels .........................................................36

Clearing Scrambled Channels - Digital ............................42

Fine Tuning Analog Channels ..........................................42

Checking the Digital-Signal Strength ...............................43

■

PC Display

Using Your TV as a Computer (PC) Display ....................44

Display Modes .................................................................44

Setting up the TV with your PC .......................................45

Time Setting

Setting the Clock .............................................................47

Function Description

Selecting a Menu Language ............................................51

Using the V-Chip ..............................................................51

Viewing Closed Captions (On-Screen Text Messages)

- Analog ...........................................................................58

Viewing Closed Captions (On-Screen Text Messages)

- Digital ............................................................................59

Adjusting the TV On/Off Melody Sound ...........................60

Setting the Entertainment mode ......................................60

Using the Energy Saving Feature ....................................61

Upgrading the Software ...................................................62

WISELINK

Using the WISELINK Function ........................................63

Using the Photo List ........................................................64

Sorting Photo List ............................................................66

Viewing a Photo or Slide Show ......................................70

Using the Music List ........................................................74

Sorting Music List ............................................................75

Playing a Music File .........................................................79

Using the Setup Menu .....................................................81

Network Settings and InfoLink

Network Connection - Cable ............................................82

Network Connection - Wireless .......................................84

Network selection ............................................................84

Cable Network Setup .......................................................85

Wireless Network Setup ..................................................87

Using InfoLink ..................................................................90

InfoLink Setup ..................................................................93

About Anynet

+

What is Anynet

+

?.............................................................94

Connecting Anynet

+

Devices...........................................94

Setting Up Anynet

+

.........................................................95

Scanning and Switching between Anynet

+

Devices ........95

Recording ........................................................................96

Listening through a Receiver (Home theater) ..................97

Troubleshooting for Anynet

+

...........................................97

Appendix

Troubleshooting ...............................................................98

Installing the Stand ........................................................100

Disconnecting the Stand ................................................100

Auto Wall-Mount Adjustment (Sold separately) ............101

Wall Mount Kit Specications (VESA) ...........................102

Using the Anti-Theft Kensington Lock (LN32A650A1F,

LN40A650A1F, LN46A650A1F) .....................................103

Specications ................................................................104

Dimensions ....................................................................105

■

English - 1

English

Contents

Symbol Press Note One-Touch Button

BN68-01599A-Eng.indb 1 2008-03-21 ¿ÀÈÄ 1:31:57

English - 2

List of Features

Adjustable picture settings that can be stored in the TV’s memory.

Automatic timer to turn the TV on and off.

A special sleep timer.

Excellent Digital Interface & Networking :

With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Cable Box/Satellite receiver

(Set-Top Box) needed.

You can view News, Weather, and Stock information over the network (SAMSUNG’s InfoLink Service).

You can listen to music les and view pictures on USB Mass Storage Class (MSC) devices.

HDMI/DVI connection of your PC to this TV.

Excellent Picture Quality

- DNIe technology provides life-like clear images.

SRS TruSurround XT

- SRS TruSurround XT provides a virtual surround system.

•

Accessories

Please make sure the following items are included with your LCD TV. If any items are missing, contact your dealer.

Remote Control & Batteries

(AAA x 2)

(BN59-00695A)

Warranty Card / Registration Card /

Safety Guide Manual

(Not available in all locations)

Cover-Bottom

(LN32A650A1F: BN63-04294A)

(LN40A650A1F: BN63-04243A)

(LN46A650A1F: BN63-04288A)

(LN52A650A1F: BN63-04330A)

Power Cord

(3903-000144)

Cleaning Cloth

(BN63-01798A)

Owner’s Instructions

Ferrite Core for Side-HDMI

(HDMI4)

(LN46A650A1F: 3301-001305)

The items color and shape may vary depending on the model.

Ferrite Core (Side-HDMI Cable)

The ferrite cores are used to shield the cables from interference. When connecting a cable, open the

ferrite core and clip it around the cable near the plug.

➣

General Information

BN68-01599A-Eng.indb 2 2008-03-21 ¿ÀÈÄ 1:31:58

English - 3

Viewing the Control Panel

Buttons on the Lower-Right Part of the Panel

The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu.

To use the more advanced features, you must use the remote control.

8 8

4

1

2

3

5

6

7

The product color and shape may vary depending on the model.

➣

Front Panel buttons

Touch each button to

operate.

1

SOURCE

Toggles between all the available input sources

(TV, AV1, AV2, S-Video, Component1, Component2,

PC, HDMI1, HDMI2/DVI, HDMI3, HDMI4, USB). In the

on-screen menu, use this button as you would use the

ENTER button on the remote control.

2

MENU

Press to see an on-screen menu of your TV’s features.

3

– VOL +

Press to increase or decrease the volume.

In the on-screen menu, use the – VOL + buttons as you

would use the ◄ and ► buttons on the remote control.

4

CH

Press to change channels.

In the on-screen menu, use the CH buttons as

you would use the ▼ and ▲ buttons on the remote

control.

5

POWER INDICATOR

Blinks and turns off when the power is on and lights up

in stand-by mode.

6

(Power)

Press to turn the TV on and off.

7

REMOTE CONTROL SENSOR

Aim the remote control towards this spot on the TV.

8

SPEAKERS

BN68-01599A-Eng.indb 3 2008-03-21 ¿ÀÈÄ 1:31:58

English - 4

Viewing the Connection Panel

Use the connection panel jacks to connect A/V components that will be connected continuously, such as DVD players or a

VCR. For more information on connecting equipment, see pages 6~12.

HDMI IN4

[TV Side Panel][TV Rear Panel]

The product color and shape may vary depending on the model.

➣

1

AUDIO OUT

Connects to the audio input jacks on your Amplier/

Home theater.

2

LAN

Connect a LAN cable to this port to connect to the

Network (SAMSUNG InfoLink’s Service).

(See pages 82~84)

3

PC IN [PC] / [AUDIO]

Connects to the video and audio output jacks on your PC.

4

HDMI IN 1, 2, 3, 4 / DVI IN(HDMI2)[R-AUDIO-L]

Connects to the HDMI jack of a device with an HDMI

output.

- No sound connection is needed for an HDMI to HDMI

connection.

Use the HDMI IN 2 jack for DVI connection to an

external device. Use a DVI to HDMI cable or DVI-HDMI

adapter (DVI to HDMI) for video connection and the

DVI IN (HDMI2) [R-AUDIO-L] jacks for audio.

- When using an HDMI/DVI cable connection, you must

use the HDMI IN 2 jack.

5

DIGITAL AUDIO OUT (OPTICAL)

Connects to a Digital Audio component.

6

ANT IN

Connects to an antenna or cable TV system.

7

WISELINK

Connect a USB mass storage device to view photo les

and play audio les.

You can connect to the network wirelessly using the

Wireless Infolink adapter (Sold separately).

8

AV IN 2

Video and audio inputs for external devices, such as a

camcorder or VCR.

S-VIDEO

Connects an S-Video signal from a camcorder or VCR.

9

(HEADPHONE)

Connects a set of external headphones for private

listening.

0

POWER INPUT

Connects the supplied power cord.

!

COMPONENT IN 1, 2 / AV IN 1

Connects Component video/audio.

The COMPONENT IN 1 jack is also used as the

AV IN 1 jack.

- Connect the video cable to the COMPONENT IN 1

[Y/VIDEO] jack and the audio cable to the

COMPONENT IN 1 [R-AUDIO-L] jacks.

@

EX-LINK

Connect this to the jack on the optional wall mount

bracket. This will allow you to adjust the TV viewing

angle using your remote control.

#

KENSINGTON LOCK

(LN32A650A1F, LN40A650A1F, LN46A650A1F)

The Kensington Lock (optional) is a device used to

physically x the system when used in a public place.

If you want to use a locking device, contact the dealer

where you purchased the TV.

The location of the Kensington Lock may be different

depending on its model.

➣

BN68-01599A-Eng.indb 4 2008-03-21 ¿ÀÈÄ 1:31:59

English - 5

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.

1

POWER

Turns the TV on and off.

2

TV

Selects the TV mode directly.

3

NUMERIC BUTTONS

Press to change the channel.

4

Press to select additional

channels (digital and analog)

being broadcast by the same

station. For example, to select

channel “54-3”, press “54”, then

press “ ” and “3”.

5

(MUTE)

Press to temporarily cut off the

sound.

6

VOL – / VOL +

Press to increase or decrease

the volume.

7

CH LIST

Used to display Channel Lists

on the screen.

8

TOOLS

Use to quickly select frequently

used functions.

9

INFO

Press to display information on

the TV screen.

0

COLOR BUTTONS

Use these buttons in the

Channel list, WISELINK, etc.

!

CC

Controls the caption decoder.

@

E.MODE

Press to select the preset

display and sound modes for

sports, cinema and games.

#

Use these buttons in the

DMA, WISELINK and Anynet

+

modes.

( : This remote can be

used to control recording on

Samsung recorders with the

Anynet

+

feature)

$

ON/OFF

Press to backlight the buttons

on the remote. This function is

convenient for using at night or

when the room is dark. (Using

the remote control with the

ON/OFF light button set

to On will reduce the battery

usage time.) (see page 16)

%

PRE-CH

Tunes to the previous channel.

^

CH / CH

Press to change channels.

&

SOURCE

Press to display and select the

available video sources.

*

W.LINK (WISELINK)

This function enables you to

view and play photo and music

les from an external device.

(Refer to pages 64 (Photo)

and 74 (Music))

(

MENU

Displays the main on-screen

menu.

)

RETURN

Returns to the previous menu.

a

 UP▲/DOWN▼/LEFT◄/

RIGHT►/ENTER

Press the Up/Down/Left/Right

sections of the wheel button

and Enter to select on-screen

menu items and change menu

values.

You can navigate up and down

the menu, switch channels and

adjust the volume by turning

the wheel button. (See pages

15~16)

b

EXIT

Press to exit the menu.

c

DMA (Digital Media Adapter)

Use this when connecting

a SAMSUNG DMA device

through an HDMI interface and

switching to DMA mode.

For more information on the

operating procedures, refer to

the user manual of the DMA.

This button is available when

“Anynet

+

(HDMI-CEC)” is “On”.

(see page 95)

d

INFO.L

Press to use the News, Stock

Market and Weather Forecast

information services available

over the network.

(see page 90)

e

FAV.CH

Press to switch to your favorite

channels.

f

P.SIZE

Picture size selection.

The performance of the remote control may be affected by bright light.

➣

BN68-01599A-Eng.indb 5 2008-03-21 ¿ÀÈÄ 1:31:59

English - 6

Installing Batteries in the Remote Control

1. Lift the cover at the back of the remote control upward as shown in the gure.

2. Install two AAA size batteries.

Make sure to match the “+” and “–” ends of the batteries with the diagram inside the

compartment.

3. Replace the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the

remote control for a long time.

The remote control can be used up to about 23 feet from the TV.

(Assuming typical TV usage, the batteries should last for about one year.)

Using the remote control with the ON/OFF light button set to On will reduce the

battery usage time.

If the remote control doesn’t work, check the following:

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage or is the power cord unplugged?

5. Is there a special uorescent light or neon sign nearby?

➣

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like the diagram to the right, see “Antennas

with 300 Ω Flat Twin Leads” below.

If your antenna has one lead that looks like the diagram to the right, see “Antennas with

75 Ω Round Leads”.

If you have two antennas, see “Separate VHF and UHF Antennas”.

Antennaswith300ΩFlatTwinLeads

If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300

Ω twin at leads, follow the directions below.

1. Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not

supplied). Use a screwdriver to tighten the screws.

2. Plug the adaptor into the ANT IN terminal on the back of the TV.

Antennaswith75ΩRoundLeads

1. Plug the antenna lead into the ANT IN terminal on the back of the TV.

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before

connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics

shops).

1. Connect both antenna leads to the combiner.

2. Plug the combiner into the ANT IN terminal on the bottom of the rear panel.

Connections

ANT IN

UHF

VHF

ANT IN

UHF

VHF

BN68-01599A-Eng.indb 6 2008-03-21 ¿ÀÈÄ 1:32:00

English - 7

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

1. Plug the incoming cable into the ANT IN terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view

unscrambled cable channels.

Connecting to a Cable Box that Descrambles All Channels

1. Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.

2. Connect the other end of this cable to the ANT IN terminal on the back of the TV.

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need

a two-way splitter, an RF (A/B) switch and four lengths of RF cable. (These items are available at most electronics stores.)

1. Find and disconnect the cable that is

connected to the ANT IN terminal on

your cable box.

This terminal might be labeled

“ANT IN”, “VHF IN” or simply, “IN”.

2. Connect this cable to a two-way

splitter.

3. Connect an RF cable between the

OUTPUT terminal on the splitter and

the IN terminal on the cable box.

4. Connect an RF cable between the

ANT OUT terminal on the cable box

and the B–IN terminal on the RF(A/B)

switch.

5. Connect another cable between the

other OUT terminal on the splitter and

the A–IN terminal on the RF (A/B)

switch.

6. Connect the last RF cable between

the OUT terminal on the RF (A/B)

switch and the ANT IN terminal on the

rear of the TV.

After you have made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B”

position to view scrambled channels. (When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s

output channel, which is usually channel 3 or 4.)

➣

ANT OUT

ANT IN

Splitter

Incoming

cable

Splitter

Cable Box

Incoming

cable

Splitter

Cable Box

RF (A/B)

Switch

Incoming

cable

ANT IN

Splitter

Cable Box

Incoming

cable

RF (A/B)

Switch

Splitter

Cable Box

Incoming

cable

TV Rear

RF (A/B)

Switch

ANT IN

BN68-01599A-Eng.indb 7 2008-03-21 ¿ÀÈÄ 1:32:01

English - 8

Connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box) via HDMI

This connection can only be made if there is an HDMI Output connector on the external device.

1. Connect an HDMI Cable

between the HDMI IN

(1, 2, 3 or 4) jack on

the TV and the HDMI

jack on the DVD Player

or Cable Box/Satellite

receiver (Set-Top Box).

What is HDMI?

• HDMI(High-Denition Multimedia Interface), is an interface that enables the

transmission of digital audio and video signals using a single cable.

• The difference between HDMI and DVI is that the HDMI device is smaller in size and

has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed.

Each DVD Player or Cable Box/Satellite receiver (Set-Top Box) has a different back

panel conguration.

The TV may not output sound and pictures may be displayed with abnormal color when

DVD players/Cable Boxes/Satellite receivers supporting HDMI versions older than 1.3

are connected. When connecting an older HDMI cable and there is no sound, connect

the HDMI cable to the HDMI IN 2 jack and the audio cables to the DVI IN (HDMI2)

[R-AUDIO-L] jacks on the back of the TV. If this happens, contact the company that

provided the DVD player/Cable Box/Satellite receiver to conrm the HDMI version, then

request an upgrade.

HDMI cables that are not 1.3 may cause annoying icker or no screen display.

➣

or

DVD Player or Cable Box/Satellite receiver

(Set-Top Box) Rear Panel

TV Rear Panel

HDMI Cable (Not supplied)

TV Side Panel

Connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box) via DVI

This connection can only be made if there is a DVI Output connector on the external device.

1. Connect a DVI to HDMI

Cable or DVI-HDMI

Adapter between the

HDMI IN 2 jack on the

TV and the DVI jack

on the DVD Player or

Cable Box/Satellite

receiver (Set-Top Box).

2. Connect Audio Cables

between the DVI IN

(HDMI 2) [R-AUDIO-L]

jack on the TV and the

DVD Player or Cable

Box/Satellite receiver

(Set-Top Box).

Each DVD Player or Cable Box/Satellite receiver (Set-Top Box) has a different back

panel conguration.

When connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box), match

the color of the connection terminal to the cable.

When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack.

➣

TV Rear Panel

DVD Player or Cable Box/

Satellite receiver (Set-Top Box)

Audio Cable (Not supplied)

2

DVI to HDMI Cable (Not supplied)

1

BN68-01599A-Eng.indb 8 2008-03-21 ¿ÀÈÄ 1:32:01

English - 9

or

TV Side Panel

Camcorder

S-Video Cable (Not supplied)

1

Audio Cable

(Not supplied)

2

Video Cable (Not supplied)

1

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV.

They allow you to view the camcorder tapes without using a VCR.

1. Connect a Video Cable

(or S-Video Cable)

between the AV IN 2

[VIDEO] (or S-VIDEO)

jack on the TV and the

VIDEO OUT jack on the

camcorder.

2. Connect Audio Cables

between the AV IN 2

[R-AUDIO-L] jacks on

the TV and the AUDIO

OUT jacks on the

camcorder.

Each Camcorder has a different back panel conguration.

When connecting a Camcorder, match the color of the connection terminal to the cable.

➣

Connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box) via Component cables

The rear panel jacks on your TV make it easy to connect a DVD Player or Cable Box/Satellite receiver (Set-Top Box) to your TV.

1. Connect a Component

Cable between the

COMPONENT IN

(1 or 2) [Y, PB, PR]

jacks on the TV and the

COMPONENT

[Y, PB, PR] jacks on the

DVD Player or Cable

Box/Satellite receiver

(Set-Top Box).

2. Connect Audio

Cables between the

COMPONENT IN(1 or

2) [R-AUDIO-L] jacks on

the TV and the AUDIO

OUT jacks on the

DVD Player or Cable

Box/Satellite receiver

(Set-Top Box).

Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and

Pr (Red) for enhanced video quality.

Be sure to match the component video and audio connections.

For example, if connecting a Component video cable to COMPONENT IN 1, connect

the audio cable to COMPONENT IN 1 also.

Each DVD Player or Cable Box/Satellite receiver (Set-Top Box) has a different back

panel conguration.

When connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box), match

the color of the connection terminal to the cable.

➣

TV Rear Panel

DVD Player or Cable Box /

Satellite receiver (Set-Top Box)

Audio Cable

(Not supplied)

2

Component Cable (Not supplied)

1

BN68-01599A-Eng.indb 9 2008-03-21 ¿ÀÈÄ 1:32:02

English - 10

Connecting a VCR

Video Connection

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the

instructions on pages 6~7). Skip step 1 if you have not yet connected to an antenna or a cable system.

1. Unplug the cable or

antenna from the back

of the TV.

2. Connect the cable or

antenna to the ANT IN

terminal on the back of

the VCR.

3. Connect an RF Cable

between the ANT OUT

terminal on the VCR

and the ANT IN terminal

on the TV.

4. Connect a Video Cable

between the VIDEO

OUT jack on the

VCR and the AV IN 1

[Y/VIDEO] or AV IN 2

[VIDEO] jack on the TV.

5. Connect Audio Cables

between the AUDIO

OUT jacks on the VCR

and the AV IN 1 (or AV

IN 2) [R-AUDIO-L] jacks

on the TV.

If you have a “mono”

(non-stereo) VCR,

use a Y-connector

(not supplied) to

connect to the right

and left audio input

jacks of the TV.

Alternatively, connect

the cable to the “R”

jack. If your VCR

is stereo, you must

connect two cables.

➣

ANT IN

Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.

Each VCR has a different back panel conguration.

When connecting a VCR, match the color of the connection terminal to the cable.

When connecting to AV IN 1, the color of the AV IN 1 [Y/VIDEO] jack (Green) does not

match the color of the video cable (Yellow).

➣

S-Video Connection

Your Samsung TV can be connected to an S-Video jack on a VCR. (This connection delivers a better picture as compared

to a standard VCR.)

1. To begin, follow steps

1–3 in the previous

section to connect the

antenna or cable to your

VCR and your TV.

2. Connect an S-Video

Cable between the

S-VIDEO OUT jack on

the VCR and the

AV IN 2 [S-VIDEO] jack

on the TV.

3. Connect Audio Cables

between the AUDIO

OUT jacks on the VCR

and the AV IN 2

[R-AUDIO-L] jacks on

the TV.

An S-Video cable may be included with a VCR. (If not, check your local electronics store.)

Each VCR has a different back panel conguration.

When connecting a VCR, match the color of the connection terminal to the cable.

➣

VCR Rear Panel

TV Rear Panel

TV Side Panel

RF Cable (Not supplied)

3

Video Cable (Not supplied)

4

Audio Cable (Not supplied)

5

VCR Rear Panel

TV Rear Panel

TV Side Panel

Audio Cable (Not supplied)

3

S-Video Cable (Not supplied)

2

RF Cable (Not supplied)

1

BN68-01599A-Eng.indb 10 2008-03-21 ¿ÀÈÄ 1:32:02

English - 11

Connecting a Digital Audio System

The rear panel jacks on your TV make it easy to connect a Digital Audio System (Home theater/Receiver) to your TV.

1. Connect an Optical Cable

between the “DIGITAL AUDIO

OUT (OPTICAL)” jacks on

the TV and the Digital Audio

Input jacks on the Digital Audio

System.

When a Digital Audio System

is connected to the “DIGITAL

AUDIO OUT (OPTICAL)” jack:

Decrease the volume of the

TV and adjust the volume

level with the system’s volume

control.

TV Rear Panel

Digital Audio System

Optical Cable (Not supplied)

5.1CH audio is possible when the TV is connected to an external device

supporting 5.1CH.

Each Digital Audio System has a different back panel conguration.

When the receiver (home theater) is set to On, you can hear sound output from

the TV’s Optical jack. When the TV is displaying a DTV(air) signal, the TV will

send out 5.1 channel sound to the Home theater receiver. When the source is a

digital component such as a DVD and is connected to the TV via HDMI, only 2

channel sound will be heard from the Home Theater receiver. If you want to hear

5.1 channel audio, connect the DIGITAL AUDIO OUT (OPTICAL) jack on the

DVD player or Cable/Satellite Box directly to an Amplier or Home Theater, not

the TV.

➣

ConnectinganAmplier/DVDHomeTheater

1. Connect Audio Cables

between the AUDIO OUT

[R-AUDIO-L] jacks on the TV

and AUDIO IN [R-AUDIO-L]

jacks on the Amplier/DVD

Home Theater.

When an audio amplier is

connected to the “AUDIO OUT

[R-AUDIO-L]” jacks: Decrease

the volume of the TV and

adjust the volume level with

the Amplier’s volume control.

TV Rear Panel

Amplier/DVDHomeTheater

Audio Cable (Not supplied)

Each Amplier/DVD Home Theater has a different back panel conguration.

When connecting an Amplier/DVD Home Theater, match the color of the

connection terminal to the cable.

➣

BN68-01599A-Eng.indb 11 2008-03-21 ¿ÀÈÄ 1:32:03

English - 12

Connecting a PC

Using the D-Sub Cable

1. Connect a D-Sub Cable

between PC IN [PC] connector

on the TV and the PC output

connector on your computer.

2. Connect a PC Audio Cable

between the PC IN [AUDIO]

jack on the TV and the Audio

Out jack of the sound card on

your computer.

TV Rear Panel

D-Sub Cable (Not supplied)

1

PC Audio Cable (Not supplied)

2

Using the HDMI/DVI Cable

1. Connect an HDMI/DVI cable

between the HDMI IN 2 jack

on the TV and the PC output

jack on your computer.

2. Connect a 3.5 mm Stereo mini-

plug/2RCA Cable between the

DVI IN(HDMI2) [R-AUDIO-L]

jack on the TV and the Audio

Out jack of the sound card on

your computer.

TV Rear Panel

3.5 mm Stereo mini-plug/2RCA Cable (Not supplied)

2

HDMI/DVI Cable (Not supplied)

1

Each PC has a different back panel conguration.

When connecting a PC, match the color of the connection terminal to the cable.

When using an HDMI/DVI cable connection, you must use the HDMI IN 2

terminal.

➣

BN68-01599A-Eng.indb 12 2008-03-21 ¿ÀÈÄ 1:32:04

English - 13

Turning the TV On and Off

Press the POWER button on the remote control.

You can also use the POWER button on the TV.

Operation

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently.

1. Press the POWER button on the remote control.

The message “Menu Language, Store Demo, Channels and Time will be

set.” is displayed.

Press the ENTER button, then “Select language of the OSD.” menu

is automatically displayed. Press the ENTER button.

2. Press the ▲ or ▼ button to select language, then press the ENTER

button.

The message “Select ‘Home Use’ when installing this TV in your home.” is

displayed.

3. Press the ◄ or ► button to select “Store Demo” or “Home Use”, then

press the ENTER button. The message “Select the Antenna source to

memorize.” is displayed.

We recommend setting the TV to “Home Use” mode for the best picture in

your home environment.

“Store Demo” mode is only intended for use in retail environments.

If the unit is accidentally set to “Store Demo” mode and you want to return

to “Home Use” (Standard): Press the Volume button on the TV. When the

volume OSD is displayed, press and hold the MENU button on the TV for

5 seconds.

4. Press the ▲ or ▼ button to memorize the channels of the selected

connection. Press the ENTER button to select “Start”.

Air: “Air” antenna signal.

Cable: “Cable” antenna signal.

Auto: “Air” and “Cable” antenna signals.

In Cable mode, you can select the correct signal source among STD,

HRC, and IRC by pressing the ▲, ▼, ◄ or ► button, then press the

ENTER button. If you have Digital cable, select the cable system

signal source for both Analog and Digital. Contact your local cable

company to identify the type of cable system that exists in your particular

area.

➣

Plug & Play

Menu Language, Store Demo, Channels and Time will

be set.

OK

Enter

Plug & Play

Select ‘Home Use’ when installing this TV in your

home.

Home Use

Store Demo

EnterMove

Plug & Play

Select language of the OSD.

Menu Language : English

EnterMove

English

Español

Français

Plug & Play

Select the Antenna source to memorize.

Air

Cable

Auto

Start

SkipEnterMove

Start

Plug & Play

Auto Program in Progress.

Stop

Cable 38

50%

DTV Air : 02 Air : 11

DTV Cable : 23 Cable : 21

SkipEnter

Start

Plug & Play

Selects the cable system.

Analog

Digital

HRC IRC

HRC IRCSTD

STD

SkipEnterMove

BN68-01599A-Eng.indb 13 2008-03-21 ¿ÀÈÄ 1:32:05

English - 14

5. The TV will begin memorizing all of the available channels.

To stop the search before it has nished, press the ENTER button with

“Stop” selected.

After all the available channels are stored, it starts to remove scrambled

channels (see page 42). And then, the Auto program menu reappears. Press

the ENTER button when channel memorization is complete. The message

“Set the Clock Mode.” is displayed.

6. Press the ENTER button.

Press the ▲ or ▼ button to select “Auto”, then Press the ENTER button.

The message “Set to daylight saving time.” is displayed.

If you select “Manual”, “Set current date and time” is displayed.

(See page 47)

7. Press the ▲ or ▼ button to select “Off” or “On”, then press the ENTER

button. The message “Select the time zone in which you live.” is displayed.

8. Press the ▲ or ▼ button to highlight the time zone for your local area. Press

the ENTER button. If you have received a digital signal, the time will be

set automatically. If not, see page 47 to set the clock.

9. The message “Enjoy your watching.” is displayed.

When you have nished, press the ENTER button.

If you want to reset this feature...

1. Press the MENU button to display the menu.

Press the ▲ or ▼ button to select “Setup”, then press the ENTER button.

2. Press the ENTER button again to select “Plug & Play”.

For further details on setting up options, refer to the pages 13~14.

The “Plug & Play” feature is only available in the TV mode.

➣

Plug & Play

Set the Clock Mode.

Clock Mode : Auto

Auto

Manual

SkipEnterMove

Plug & Play

Set to daylight saving time.

DST : Auto

Off

On

SkipEnter

Move

Plug & Play

Enjoy your watching.

OK

Setup

Plug&Play  ►

Language : English

Time

Network selection : Cable

Cable Network Setup

Wireless Network Setup

V-Chip

Caption

Plug & Play

Select the time zone in which you live.

Newfoundland

Atlantic

Eastern

Central

Mountain

Pacific



SkipEnter

Move

Plug & Play

Removing scrambled channel.

Stop

DTV Cable 41

77%

DTV Air : 05 Air : 12

DTV Cable : 25 Cable : 32

SkipEnter

Plug & Play

Auto Program is completed.

119 channels are memorized.

DTV Air : 05 Air : 24

DTV Cable : 10 Cable : 80

OK

SkipEnter

BN68-01599A-Eng.indb 14 2008-03-21 ¿ÀÈÄ 1:32:06

English - 15

Changing Channels

Using the Channel Buttons

1. Press the CH or CH button to change channels.

When you press the CH or CH button, the TV changes channels in

sequence.

You will see all the channels that the TV has memorized. (The TV must

have memorized at least three channels). You will not see channels that

were either erased or not memorized. See page 18 to memorize channels.

To increase the channel number, turn the wheel clockwise when the

Channel Display is displayed. To decrease the channel number, turn the

wheel counterclockwise.

Using the Number Buttons

1. Press the number buttons to go directly to a channel. For example, to select

channel 27, press 2, then 7.

For quick channel change, press the number buttons, then press the

ENTER button.

Using the Button

The button is used to select stations that broadcast a digital signal.

1. For example, for Channel 7-1, press 7, then , then 1.

HD indicates the TV is receiving a Digital High Denition signal.

SD indicates the TV is receiving a Standard Denition signal.

For quick channel change, press the number buttons, then press the

ENTER button.

Using the PRE-CH Button to select the Previous Channel

1. Press the PRE-CH button. The TV will switch to the last channel viewed.

To quickly switch between two channels that are far apart, tune to one

channel, then use the number button to select the second channel.

Then use the PRE-CH button to quickly alternate between them.

➣

Adjusting the Volume

Using the Volume Button

1. Press the VOL – or VOL+ button to increase or decrease the volume.

To turn the volume up, turn the wheel clockwise when the Volume

Control window is displayed. To turn the volume down, turn the wheel

counterclockwise.

Using the MUTE button

At any time, you can cut off the sound using the MUTE button.

1. Press MUTE button and the sound cuts off.

“ ” is displayed on the screen.

2. To turn mute off, press the MUTE button again or simply press the

VOL – or VOL+ button.

➣

BN68-01599A-Eng.indb 15 2008-03-21 ¿ÀÈÄ 1:32:06

English - 16

Viewing the Display

The display identies the current channel and the status of certain audio-video

settings.

1. Press the INFO button on the remote control.

The TV will display the channel, the type of sound, and the status of certain

picture and sound settings.

Press the INFO button once more or wait approximately 10 seconds and

the display disappears automatically.

➣

Viewing the Menus

1. With the power on, press the MENU button.

The main menu appears on the screen.

The menu’s left side has icons: Picture, Sound, Channel, Setup, Input,

Application.

2. Press the ▲ or ▼ button to select one of the icons.

Then press the ENTER button to access the icon’s sub-menu.

To move to a lower menu, turn the wheel clockwise when the menu Display

is displayed. To move to a higher menu, turn the wheel counterclockwise.

3. Press the EXIT button to exit.

The on-screen menus disappear from the screen after about one minute.

➣

Using the Remote Control Backlight Buttons

Use this feature in dark surroundings and when you are unable to see the remote control buttons clearly.

1. Press the ON/OFF light button.

Pressing the ON/OFF light button toggles between ON and OFF.

When ON, the button backlight is turned on for a moment.

Pressing a remote control button when the remote control is on turns the button backlight on for a moment. If

you touch or move the remote control and the motion is detected by the sensor of the remote control, the button

backlight will be turned on for a moment.

The remote contains two small movement sensors that control the backlight function. If you shake or drop the

remote, you may hear the sensors rattle. This is normal and is not a defect.

The button backlight will not be turned on when the remote control is turned off.

➣

Mode

:

Standard

Backlight : 7

Contrast : 95

Brightness : 45

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

Detailed Settings

Picture

DTV Air

4-2

♥

TV #8

Dolby Digital

9:59 am - 10:59 am

Sun, Sep 3 1:45 pm

Life On Venus Avenue

No Detaild Information

1080i

|

16:9

|

English

BN68-01599A-Eng.indb 16 2008-03-21 ¿ÀÈÄ 1:32:07

English - 17

Using the TOOLS Button

You can use the TOOLS button to select your frequently used functions quickly and easily. The “TOOLS” menu changes

depending on which external input mode you are viewing.

1. Press the TOOLS button. The “TOOLS” menu will appear.

2. Press the ▲ or ▼ button to select a menu.

3. Press the ▲/▼/◄/►/ENTER buttons to display, change, or use the selected

items. For a more detailed description of each function, refer to the corresponding

page.

Device List: see page 95

Multi-Track Sound: see pages 33

Picture Mode: see page 20

Sound Mode: see page 31

Sleep Timer: see page 49

Add to Favorite: see page 38

Switch to Cable (or Switch to Air): see page 17

PIP: see page 30

Auto adjustment: see page 45

•

Memorizing the Channels

Your TV can memorize and store all of the available channels for both “off-air” (Air) and “Cable” channels. After the available

channels are memorized, use the CH or CH button to scan through the channels. This eliminates the need to change

channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source,

memorizing the channels (automatic) and adding or deleting channels (Channel Lists).

Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must

specify the type of signal source that is connected to the TV (i.e. an Air or a Cable

system).

1. Press the MENU button to display the menu.

Press the ▲ or ▼ button to select “Channel”, then press the ENTER

button.

2. Press the ENTER button to select “Antenna”.

Press the ▲ or ▼ button to select “Air” or “Cable”, then press the ENTER

button.

Press the EXIT button to exit.

Easy Setting

1. Press the TOOLS button on the remote control.

2. Press the ▲ or ▼ button to select “Switch to Cable (or Switch to Air)”.

3. Press the ENTER button to switch “Cable” (or “Air”).

Channel

Antenna

:

Air ►

Auto Program

Clear Scrambled Channel

Channel List

Fine Tune

Signal Strength

Channel

Antenna

:

Air ►

Auto Program

Clear Scrambled Channel

Channel List

Fine Tune

Signal Strength

Air

Cable

TOOLS

Device List

Multi-Track Sound : Stereo

Picture Mode : Standard

Sound Mode : Custom

Sleep Timer : Off

Add to Favorite

Switch to Cable

Move Enter

e

Exit

TOOLS

Device List

Multi-Track Sound : Stereo

Picture Mode : Standard

Sound Mode : Custom

Sleep Timer : Off

Add to Favorite

Switch to Cable

Move Enter

e

Exit

BN68-01599A-Eng.indb 17 2008-03-21 ¿ÀÈÄ 1:32:07

English - 18

Storing Channels in Memory (Automatic Method)

1. Press the MENU button to display the menu.

Press the ▲ or ▼ button to select “Channel”, then press the ENTER

button.

2. Press the ▲ or ▼ button to select “Auto Program”, then press the ENTER

button.

3. Press the ▲ or ▼ button to select the antenna connection, then press the

ENTER button.

Air: “Air” antenna signal.

Cable: “Cable” antenna signal.

Auto: “Air” and “Cable” antenna signals.

4. When selecting the Cable TV system:

Press the ENTER button to start the auto program.

Press the ▲,▼, ◄ or ► to select the correct analog signal cable system

source among “STD”, “HRC”, and “IRC”. Press the ▲ or ▼ button to select

“Start”, then press the ENTER button. If you have Digital cable TV, select

the cable system signal source for both Analog and Digital.

STD, HRC and IRC identify various types of cable TV systems. Contact

your local cable company to identify the type of cable system that exists in

your particular area. At this point the signal source has been selected.

5. The TV begins memorizing all available stations.

After all the available channels are stored, it starts to remove scrambled

channels (see page 42). The Auto program menu then reappears.

If you want to stop Auto Programming, press the ENTER button.

The “Stop Auto Program?” message will be displayed. Select “Yes” by

pressing the ◄ or ► button, then press the ENTER button.

Press the EXIT button to exit.

➣

Channel

Antenna

:

Air

Auto Program  ►

Clear Scrambled Channel

Channel List

Fine Tune

Signal Strength

ReturnEnter

Auto Program

Select the Antenna source to memorize.

Air

Cable

Auto

Move

Start

Auto Program

Auto Program is completed.

90 channels are memorized.

Air : 10 Cable : 80

OK

ReturnEnter

Auto Program

Auto Program in Progress.

Stop

Enter

Cable 38

50%

Return

DTV Cable : 12 Cable : 32

Auto Program

Stop Auto Program?

77%

ReturnEnter

No

Yes

Move

DTV Cable : 16 Cable : 45

Auto Program

Removing scrambled channel.

Stop

Enter

DTV Cable 41

77%

Return

DTV Cable : 16 Cable : 45

ReturnEnter

Auto Program

Selects the cable system.

Analog

Digital

HRC IRC

Move

STD

Start

STD

BN68-01599A-Eng.indb 18 2008-03-21 ¿ÀÈÄ 1:32:08

La page charge ...

Samsung LN32A650A1F Manuel utilisateur

Ce manuel convient également à

Samsung LN32A650A1F Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents