LG DLE1001W Le manuel du propriétaire
- Catégorie
- Sèche-linge
- Taper
- Le manuel du propriétaire
OWNER’S MANUAL
DRYER
Please read this owner’s manual thoroughly before
operating and keep it handy for reference at all times.
P/No. : 3828EL2001X
www.lg.com
ENGLISH FRANÇAIS
DLE1001W DLG1002W
2
3
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
w
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER, WARNING, or CAUTION.
These words mean:
w
DANGER
You will be killed or seriously injured if you don’t immediately follow instructions.
w
WARNING
You can be killed or seriously injured if you don’t follow instructions.
w
CAUTION
You may be slightly injured or cause damage to the product if you do not follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell
you what can happen if the instructions are not followed.
w
WARNING:
This product contains chemicals known to the State of California to cause cancer and birth defects or
other reproductive harm.
Wash hands after handling.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRU CTIONS
TABLE OF CONTENTS
3
IMPORTANT SAFETY INSTRUCTIONS
3 WHAT TO DO IF YOU SMELL GAS
4 BASIC SAFETY PRECAUTIONS
5 GROUNDING INSTRUCTIONS
5 SAFETY INSTRUCTIONS FOR INSTALLATION
7 SAFETY INSTRUCTIONS FOR CONNECTING
ELECTRICITY
8
PRODUCT FEATURES
9
INTRODUCING YOUR DRYER
9 Parts
9 Accessories
10 Control Panel Features
11 Display
12
INSTALLATION INSTRUCTIONS
12 Preview Installation Order
13 Installation Location Requirements
13 Clearances
14 Leveling the Dryer
15 Reversing the Door
16 Installing the Side Vent Kit
17 Venting the Dryer
19 Connecting Gas Dryers
21 Connecting Electric Dryers
22 Special Requirements for Manufactured or
Mobile Homes
22 Final Installation Check
23 Installation Test (Duct Check)
25
HOW TO USE
25 Operating the Dryer
26 Cycle Guide
27 Sorting Laundry
27 Loading the Dryer
27 Check the Lint Filter Before Every Load
28 Cycle Setting Buttons
29 Special Functions
29 Custom Program
30
MAINTENANCE
30 Regular Cleaning
31
TROUBLESHOOTING
31 Before Calling for Service
33
SPECIFICATIONS
34
USING SMARTDIAGNOSIS
TM
35
WARRANTY
2
3
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
w
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER, WARNING, or CAUTION.
These words mean:
w
DANGER
You will be killed or seriously injured if you don’t immediately follow instructions.
w
WARNING
You can be killed or seriously injured if you don’t follow instructions.
w
CAUTION
You may be slightly injured or cause damage to the product if you do not follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell
you what can happen if the instructions are not followed.
w
WARNING:
This product contains chemicals known to the State of California to cause cancer and birth defects or
other reproductive harm.
Wash hands after handling.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRU CTIONS
TABLE OF CONTENTS
3
IMPORTANT SAFETY INSTRUCTIONS
3 WHAT TO DO IF YOU SMELL GAS
4 BASIC SAFETY PRECAUTIONS
5 GROUNDING INSTRUCTIONS
5 SAFETY INSTRUCTIONS FOR INSTALLATION
7 SAFETY INSTRUCTIONS FOR CONNECTING
ELECTRICITY
8
PRODUCT FEATURES
9
INTRODUCING YOUR DRYER
9 Parts
9 Accessories
10 Control Panel Features
11 Display
12
INSTALLATION INSTRUCTIONS
12 Preview Installation Order
13 Installation Location Requirements
13 Clearances
14 Leveling the Dryer
15 Reversing the Door
16 Installing the Side Vent Kit
17 Venting the Dryer
19 Connecting Gas Dryers
21 Connecting Electric Dryers
22 Special Requirements for Manufactured or
Mobile Homes
22 Final Installation Check
23 Installation Test (Duct Check)
25
HOW TO USE
25 Operating the Dryer
26 Cycle Guide
27 Sorting Laundry
27 Loading the Dryer
27 Check the Lint Filter Before Every Load
28 Cycle Setting Buttons
29 Special Functions
29 Custom Program
30
MAINTENANCE
30 Regular Cleaning
31
TROUBLESHOOTING
31 Before Calling for Service
33
SPECIFICATIONS
34
USING SMARTDIAGNOSIS
TM
35
WARRANTY
w
4
5
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
w
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
• Read all instructions before using the dryer.
• Before use, the dryer must be properly installed as
described in this manual.
• Do not place items exposed to cooking oils in your
dryer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a
load to catch fire.
• Do not dry articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline, dry-
cleaning solvents, or other flammable or explosive
substances as they give off vapors that could ignite or
explode.
• Do not reach into the dryer if the drum or any other
part is moving.
• Do not repair or replace any part of the dryer
or attempt any servicing unless specifically
recommended in this owner’s manual or in published
user-repair instructions that you understand and have
the skills to carry out.
• Do not tamper with controls.
• Before the dryer is removed from service or discarded,
remove the door to the drying compartment.
• Do not allow children to play on or in the dryer. Close
supervision of children is necessary when the dryer is
used near children.
• Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of
the fabric softener or product.
• Do not use heat to dry articles containing foam rubber
or similarly textured rubber-like materials.
• Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint,
dust, and dirt.
• The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
• Do not install or store the dryer where it will be
exposed to the weather.
• Always check the inside of the dryer for foreign
objects.
• Clean lint screen before or after each load.
•
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
w
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
w
WARNING
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a
qualified electrician or service person if you are in doubt that the appliance is properly grounded.
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
•
Follow details in
the installation instructions. Electric shock can result if
the dryer is not properly grounded.
• as
described in this manual. Electric shock can result if
the dryer is not properly grounded.
•
•
Failure to follow this
warning can cause serious injury, fire, electric shock, or
death.
•
Failure to follow this
warning can cause serious injury, fire, electric shock, or
death.
•
Improper
power circuit can melt, creating electric shock and/or
fire hazard.
•
Failure to do so can
result in death, explosion, fire, or burns.
•
Failure to do so can result in
death, explosion, fire, or burns.
• Packaging
material can be dangerous for children. There is a risk
of suffocation.
•
Failure to observe this
warning can cause product deformation, smoke and
fire.
•
Dripping wax,
smoke, or fire can result.
•
Failure to do so can cause product damage, smoke or
fire.
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of least
resistance for electric current. This appliance must be
equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
Do not modify the plug provided with the appliance. If
it will not fit the outlet, have a proper outlet installed by
a qualified electrician.
This appliance must be connected to a grounded metal,
permanent wiring system or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or
lead on the appliance.
Electric shock can result if the dryer is not properly
grounded.
IMPORTANT SAFETY INSTRU CTIONS IMPORTANT SAFETY INSTRU CTIONS
4
5
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
w
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
• Read all instructions before using the dryer.
• Before use, the dryer must be properly installed as
described in this manual.
• Do not place items exposed to cooking oils in your
dryer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a
load to catch fire.
• Do not dry articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline, dry-
cleaning solvents, or other flammable or explosive
substances as they give off vapors that could ignite or
explode.
• Do not reach into the dryer if the drum or any other
part is moving.
• Do not repair or replace any part of the dryer
or attempt any servicing unless specifically
recommended in this owner’s manual or in published
user-repair instructions that you understand and have
the skills to carry out.
• Do not tamper with controls.
• Before the dryer is removed from service or discarded,
remove the door to the drying compartment.
• Do not allow children to play on or in the dryer. Close
supervision of children is necessary when the dryer is
used near children.
• Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of
the fabric softener or product.
• Do not use heat to dry articles containing foam rubber
or similarly textured rubber-like materials.
• Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint,
dust, and dirt.
• The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
• Do not install or store the dryer where it will be
exposed to the weather.
• Always check the inside of the dryer for foreign
objects.
• Clean lint screen before or after each load.
•
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
w
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
w
WARNING
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a
qualified electrician or service person if you are in doubt that the appliance is properly grounded.
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
•
Follow details in
the installation instructions. Electric shock can result if
the dryer is not properly grounded.
• as
described in this manual. Electric shock can result if
the dryer is not properly grounded.
•
•
Failure to follow this
warning can cause serious injury, fire, electric shock, or
death.
•
Failure to follow this
warning can cause serious injury, fire, electric shock, or
death.
•
Improper
power circuit can melt, creating electric shock and/or
fire hazard.
•
Failure to do so can
result in death, explosion, fire, or burns.
•
Failure to do so can result in
death, explosion, fire, or burns.
• Packaging
material can be dangerous for children. There is a risk
of suffocation.
•
Failure to observe this
warning can cause product deformation, smoke and
fire.
•
Dripping wax,
smoke, or fire can result.
•
Failure to do so can cause product damage, smoke or
fire.
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of least
resistance for electric current. This appliance must be
equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
Do not modify the plug provided with the appliance. If
it will not fit the outlet, have a proper outlet installed by
a qualified electrician.
This appliance must be connected to a grounded metal,
permanent wiring system or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or
lead on the appliance.
Electric shock can result if the dryer is not properly
grounded.
IMPORTANT SAFETY INSTRU CTIONS IMPORTANT SAFETY INSTRU CTIONS
6
7
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
w
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
w
WARNING
To reduce the risk of injury to persons, follow all industry recommended safety procedures including the use of long
sleeved gloves and safety glasses. Failure to follow all of the safety warnings in this manual could result in property
damage, injury to persons, or death.
Exhaust/Ducting:
•
Failure to follow these instructions can result in fire or
death.
•
. An accumulation of lint in any area of
the home can create a health and fire hazard.
•
Punctured
ductwork can cause a fire if it collapses or becomes
otherwise restricted in use or during installation.
•
Failure to
follow these instructions can result in fire or death.
•
dryer. Failure to follow these instructions can result in
fire or death.
•
Failure to
follow these instructions can result in fire or death.
•
Secure
all joints with duct tape. For complete details, follow
the Installation Instructions. Failure to follow these
instructions can result in fire or death.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
w
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
•
To prevent
injury to persons or damage to the dryer, the electrical
power cord must be plugged into a properly grounded
outlet.
•
Failure to do so can result in electric shock
or injury.
•
Failure to follow these instructions can create an
electric shock hazard and/or a fire hazard.
•
Failure to follow these instructions can create an
electric shock hazard and/or a fire hazard.
•
This provides
best performance and also prevents overloading
house wiring circuits which could cause a fire hazard
from overheated wires.
•
The power cord can be damaged,
resulting in a risk of fire and electric shock.
•
The power cord can
melt, creating an electric shock and/or fire hazard.
•
This will
prevent injury and prevent damage to the dryer from
fire and electric shock.
IMPORTANT SAFETY INSTRU CTIONS IMPORTANT SAFETY INSTRUCTIONS
6
7
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
w
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
w
WARNING
To reduce the risk of injury to persons, follow all industry recommended safety procedures including the use of long
sleeved gloves and safety glasses. Failure to follow all of the safety warnings in this manual could result in property
damage, injury to persons, or death.
Exhaust/Ducting:
•
Failure to follow these instructions can result in fire or
death.
•
. An accumulation of lint in any area of
the home can create a health and fire hazard.
•
Punctured
ductwork can cause a fire if it collapses or becomes
otherwise restricted in use or during installation.
•
Failure to
follow these instructions can result in fire or death.
•
dryer. Failure to follow these instructions can result in
fire or death.
•
Failure to
follow these instructions can result in fire or death.
•
Secure
all joints with duct tape. For complete details, follow
the Installation Instructions. Failure to follow these
instructions can result in fire or death.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
w
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
•
To prevent
injury to persons or damage to the dryer, the electrical
power cord must be plugged into a properly grounded
outlet.
•
Failure to do so can result in electric shock
or injury.
•
Failure to follow these instructions can create an
electric shock hazard and/or a fire hazard.
•
Failure to follow these instructions can create an
electric shock hazard and/or a fire hazard.
•
This provides
best performance and also prevents overloading
house wiring circuits which could cause a fire hazard
from overheated wires.
•
The power cord can be damaged,
resulting in a risk of fire and electric shock.
•
The power cord can
melt, creating an electric shock and/or fire hazard.
•
This will
prevent injury and prevent damage to the dryer from
fire and electric shock.
IMPORTANT SAFETY INSTRU CTIONS IMPORTANT SAFETY INSTRUCTIONS
8
9
INTRODUCING YOUR DRYER
PARTS AND ACCESSORIES
Parts
Accessories
Control
panel
Leveling
feet
Reversible
door
Lint filter
Terminal
block
access panel
(Electric
models)
Gas
connection
location
(Gas models)
Power cord
location
(Gas
models)
Exhaust
duct
outlet
NOTE
• Contact LG Customer Service at 1-800-243-0000 (1-888-542-2623 in Canada) if any accessories are missing.
• For your safety and for extended product life, use only authorized components. The manufacturer is not
responsible for product malfunction or accidents caused by the use of separately purchased unauthorized
components or parts.
• The images in this owner’s manual may be different from the actual components and accessories, and are subject
to change by the manufacturer without prior notice for product improvement purposes.
PRODUCT FEATURES
EASY-TO-USE CONTROL PANEL
An entire selection of user-friendly functions make operating the dryer easy.
EASY-ACCESS REVERSIBLE DOOR
The wide-opening door provides easy access for loading and unloading. The door hinge can be reversed to
adjust for installation location.
FLOW SENSE™ DUCT BLOCKAGE SENSING SYSTEM INDICATOR
The FLOW SENSE(TM) duct blockage sensing system detects and alerts you to restrictions in the installed
household ductwork that reduce exhaust airflow through the dryer. If you see the alert, clean or repair the
ducts to remove the restrictions. Keep your ducts clean to help increase efficiency and reduce long drying
times caused by blocked ducts.
SMARTDIAGNOSIS™
Should you experience any technical difficulty with your dryer, it has the capability of transmitting data via
your telephone to the Customer Information Center. The call center agent records the data transmitted from
your machine and uses it to analyze the issue, providing a fast and effective diagnosis (refer to page 38 ).
C
E
R
T
I
F
I
E
D
D
E
S
I
G
N
PRODUCT FEATURES INTRODUCING YOUR DRYER
8
9
ENGLISH
INTRODUCING YOUR DRYER
PARTS AND ACCESSORIES
Parts
Accessories
Control
panel
Leveling
feet
Reversible
door
Lint filter
Terminal
block
access panel
(Electric
models)
Gas
connection
location
(Gas models)
Power cord
location
(Gas
models)
Exhaust
duct
outlet
NOTE
• Contact LG Customer Service at 1-800-243-0000 (1-888-542-2623 in Canada) if any accessories are missing.
• For your safety and for extended product life, use only authorized components. The manufacturer is not
responsible for product malfunction or accidents caused by the use of separately purchased unauthorized
components or parts.
• The images in this owner’s manual may be different from the actual components and accessories, and are subject
to change by the manufacturer without prior notice for product improvement purposes.
PRODUCT FEATURES INTRODUCING YOUR DRYER
10
11
Control panel features
Following are instructions for starting and using your new dryer. Please refer to specific sections of this manual for
more detailed information.
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the Important Safety
Instructions, before operating this dryer.
Display
Following are instructions for starting and using your new dryer. Please refer to specific sections of this manual for
more detailed information.
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the Important Safety
Instructions, before operating this dryer.
Press to turn the dryer ON. Press again to turn
the dryer OFF.
A
This portion of the display shows which stage of
the drying cycle is currently underway (CHECK
FILTER, DRY, COOLING, or WRINKLE CARE).
B
When CHILD LOCK is set, the CHILD LOCK
indicator will appear and all buttons are disabled
except the POWER button. This prevents children
from changing settings while the dryer is
operating.
C
Press the CYCLES button repeatedly to scroll
through the cycle selections until the desired
cycle is selected. The standard presets for the
selected cycle will be shown in the display.
On MANUAL DRY cycles, these settings can be
adjusted using the cycle setting buttons anytime
before starting the cycle.
B
Press this button to START the selected cycle. If
the dryer is running, use this button to PAUSE
the cycle without losing the current settings.
C
Use these buttons to select the desired cycle
settings for the selected cycle. The current
settings are shown in the display. Press the
button for that option to select other settings.
E
Use these buttons with the TIME DRY and other
MANUAL DRY cycles to adjust the drying time.
Press the MORE TIME button to increase the
selected manual cycle time by one minute;
press LESS TIME to decrease the cycle time by
one minute.
D
The display shows the settings, estimated time
remaining, options, and status messages for
your dryer.
F
G
The OPTION buttons allow you to select
additional cycle options. Certain buttons also
allow you to activate special functions by
pressing and holding the button for 3 seconds.
A
F
CB
DGE
NOTE
Pressing the ON/OFF button during a cycle will
cancel that cycle and any load settings will be lost.
AUTO OFF : To conserve energy, the dryer shuts off
automatically after a cycle is complete or anytime
the dryer is paused for more than a few minutes.
This display shows the estimated time remaining
for SENSOR DRY cycles or the actual time
remaining for TIMED DRY or MANUAL DRY cycles.
A
NOTE
The cycle time on SENSOR DRY cycles may
fluctuate as the dryer recalculates drying time for
optimal results.
NOTE
If you do not press the START/PAUSE button to
resume a cycle within 4 minutes, the dryer turns
off automatically.
INTRODUCING YOUR DRYER INTRODUCING YOUR DRYER
10
11
ENGLISH
Display
Following are instructions for starting and using your new dryer. Please refer to specific sections of this manual for
more detailed information.
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the Important Safety
Instructions, before operating this dryer.
This portion of the display shows which stage of
the drying cycle is currently underway (CHECK
FILTER, DRY, COOLING, or WRINKLE CARE).
B
When CHILD LOCK is set, the CHILD LOCK
indicator will appear and all buttons are disabled
except the POWER button. This prevents children
from changing settings while the dryer is
operating.
C
Use these buttons to select the desired cycle
settings for the selected cycle. The current
settings are shown in the display. Press the
button for that option to select other settings.
E
The display will show CHECK FILTER when the
dryer is turned on as a reminder to check the
filter. It turns off when the START/PAUSE button
is pressed.
D
If you have a special combination of settings
that you use frequently, you can save these
settings as a CUSTOM PROGRAM.
E
The FLOW SENSE(TM) duct blockage sensing
system detects and alerts you to restrictions in
the installed household ductwork that reduce
exhaust airflow through the dryer. If you see
the alert, clean or repair the ducts to remove
the restrictions. Keep your ducts clean to help
increase efficiency, reduce long drying times
caused by blocked ducts, and help to minimize
service calls, saving you money.
F
The display shows the settings, estimated time
remaining, options, and status messages for
your dryer.
F
G
The OPTION buttons allow you to select
additional cycle options. Certain buttons also
allow you to activate special functions by
pressing and holding the button for 3 seconds.
A
F
CB
DGE
This display shows the estimated time remaining
for SENSOR DRY cycles or the actual time
remaining for TIMED DRY or MANUAL DRY cycles.
A
NOTE
The cycle time on SENSOR DRY cycles may
fluctuate as the dryer recalculates drying time for
optimal results.
INTRODUCING YOUR DRYER INTRODUCING YOUR DRYER
A
F
CB
DGE
F
D
B
A
E
C
12
13
Installation location requirements
w
WARNING
It is important that
you review this entire manual before installing and using your dryer. Detailed instructions concerning electrical
connections, gas connections, and exhaust requirements are provided on the following pages.
Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off
at the end of an automatic cycle. This can result in longer drying times. The dryer must not be installed or stored in
an area where it will be exposed to water and/or weather. Check code requirements. Some codes limit, or do not
permit, installation of the dryer in garages, closets, mobile homes or
sleeping quarters. Contact your local building inspector.
Clearances
INSTALLATION SPACING FOR RECESSED AREA OR CLOSET INSTALLATION
The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0
inches (0 cm) clearance on the sides and rear. Recommended spacing should be considered for the following
reasons:
• A location that allows for proper exhaust installation. A
gas dryer must be exhausted to the outdoors.
See
• A grounded electrical outlet located within 2 ft.
(61 cm) of either side of the dryer. See
• A sturdy floor to support the total dryer weight of 200
lbs (90.7 kg). The combined weight of a companion
appliance should also be considered.
• No other fuel-burning appliance can be installed in the
same closet as a dryer.
• Additional spacing should be considered for ease of
installation and servicing.
• Additional clearances might be required for wall, door
and floor moldings.
• Additional spacing should be considered on all sides
of the dryer to reduce noise transfer.
For closet installation, with a door, minimum
ventilation openings in the top and bottom of the
door are required. Louvered doors with equivalent
ventilation openings are acceptable.
• Companion appliance spacing should also be
considered.
1"* (2,5 cm)
5
"**
(14 cm)
1/2
77
1/2
"
(196,8 cm)
3"* (7,6 cm)
6"*(15,2 cm)
3"* (7,6 cm)
27"
(68,6 cm)
1"
(2,5 cm)
1"
(2,5 cm)
24 in.
2*
(155 cm
2
)
48 in.
2*
(310 cm
2
)
Closet Door Vent
Requirements
Requisitos de ventilación
de la puerta del armario
(2,54 cm) (2,54 cm)
(7,6 cm)
(7,6 cm)
(7.6 cm)
(7.6 cm)
(68,6 cm)
(2.54 cm) (2.54 cm)(68.6 cm)
28
(73.4 cm)
7"* (17.8 cm)
7"* (17.8 cm)
5"*
(12.7 cm)
1"*
(2.5 cm)
(68.6 cm)
1"
(2.54 cm)
1"
(2.54 cm)
(2,54 cm) (2,54 cm)
(7,6 cm)
(7,6 cm)
(68,6 cm)
28
(73,4 cm)
7"* (17,8 cm)
7"* (17,8 cm)
5"*
(12,7 cm)
1"*
(2,5 cm)
27
"
(68,6 cm)
1"
(2,54 cm)
27
"
1"
(2,54 cm)
28
(73,4 cm)
7"* (17,8 cm)
7"* (17,8 cm)
5"*
(12,7 cm)
1"*
(2,5 cm)
(68,6 cm)
1"
(2,54 cm)
1"
(2,54 cm)
14
"
max.*
(35.6
cm)
21
1
/
4
"
(54 cm)
28
15
/
16
"
(73.4 cm)
50
1
/
4
"
(127.5 cm)
5"**
(12.7 cm)
40
3
/
16
"
(102 cm)
14
"
max.*
(35,6
cm)
21
1
/
4
"
(54 cm)
28
15
/
16
"
(73,4 cm)
50
1
/
4
"
(127,5 cm)
5"**
(12,7 cm)
40
3
/
16
"
(102 cm)
14
"
max.*
(35,6
cm)
21
1
/
4
"
(54 cm)
28
15
/
16
"
(73,4 cm)
50
1
/
4
"
(127,5 cm)
5"**
(12,7 cm)
40
3
/
16
"
(102 cm)
27
"
INSTALLATION INSTRUCTIONS
PREVIEW INSTALLATION ORDER
Checking and
choosing the proper
location
Leveling the dryer Venting the Dryer
Installation check
(Refer to page 27.)
Connecting Gas Dryers
(Gas Dryer Type)
Connecting Electric Dryers
(Electric Dryer Type)
Plugging in the power cord
and grounding
Test run
Press and hold
120V
240V
NOTE
• Floor must be level, with a maximum slope of 1 inch (2.5 cm) under entire dryer. If slope is greater than 1 inch (2.5
cm), install the Extended Dryer Feet Kit. Clothes may not tumble properly, and automatic sensor cycles may not
operate correctly if dryer is not level.
• For a garage installation, you will need to place the dryer at least 18 inches (46 cm) above the floor. If using a
pedestal, you will need 18 inches (46 cm) to the bottom of the dryer.
NOTE
There should be at least a little space around the dryer (or any other appliance) to eliminate the transfer of
vibration from one to the other. If there is too much vibration, it could cause them to make noise or touch each
other causing paint damage and making even more noise.
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
12
13
ENGLISH
Installation location requirements
w
WARNING
It is important that
you review this entire manual before installing and using your dryer. Detailed instructions concerning electrical
connections, gas connections, and exhaust requirements are provided on the following pages.
Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off
at the end of an automatic cycle. This can result in longer drying times. The dryer must not be installed or stored in
an area where it will be exposed to water and/or weather. Check code requirements. Some codes limit, or do not
permit, installation of the dryer in garages, closets, mobile homes or
sleeping quarters. Contact your local building inspector.
Clearances
INSTALLATION SPACING FOR RECESSED AREA OR CLOSET INSTALLATION
The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0
inches (0 cm) clearance on the sides and rear. Recommended spacing should be considered for the following
reasons:
• A location that allows for proper exhaust installation. A
gas dryer must be exhausted to the outdoors.
See
• A grounded electrical outlet located within 2 ft.
(61 cm) of either side of the dryer. See
• A sturdy floor to support the total dryer weight of 200
lbs (90.7 kg). The combined weight of a companion
appliance should also be considered.
• No other fuel-burning appliance can be installed in the
same closet as a dryer.
• Additional spacing should be considered for ease of
installation and servicing.
• Additional clearances might be required for wall, door
and floor moldings.
• Additional spacing should be considered on all sides
of the dryer to reduce noise transfer.
For closet installation, with a door, minimum
ventilation openings in the top and bottom of the
door are required. Louvered doors with equivalent
ventilation openings are acceptable.
• Companion appliance spacing should also be
considered.
1"* (2,5 cm)
5
"**
(14 cm)
1/2
77
1/2
"
(196,8 cm)
3"* (7,6 cm)
6"*(15,2 cm)
3"* (7,6 cm)
27"
(68,6 cm)
1"
(2,5 cm)
1"
(2,5 cm)
24 in.
2*
(155 cm
2
)
48 in.
2*
(310 cm
2
)
Closet Door Vent
Requirements
Requisitos de ventilación
de la puerta del armario
(2,54 cm) (2,54 cm)
(7,6 cm)
(7,6 cm)
(7.6 cm)
(7.6 cm)
(68,6 cm)
(2.54 cm) (2.54 cm)(68.6 cm)
28
(73.4 cm)
7"* (17.8 cm)
7"* (17.8 cm)
5"*
(12.7 cm)
1"*
(2.5 cm)
(68.6 cm)
1"
(2.54 cm)
1"
(2.54 cm)
(2,54 cm) (2,54 cm)
(7,6 cm)
(7,6 cm)
(68,6 cm)
28
(73,4 cm)
7"* (17,8 cm)
7"* (17,8 cm)
5"*
(12,7 cm)
1"*
(2,5 cm)
27
"
(68,6 cm)
1"
(2,54 cm)
27
"
1"
(2,54 cm)
28
(73,4 cm)
7"* (17,8 cm)
7"* (17,8 cm)
5"*
(12,7 cm)
1"*
(2,5 cm)
(68,6 cm)
1"
(2,54 cm)
1"
(2,54 cm)
14
"
max.*
(35.6
cm)
21
1
/
4
"
(54 cm)
28
15
/
16
"
(73.4 cm)
50
1
/
4
"
(127.5 cm)
5"**
(12.7 cm)
40
3
/
16
"
(102 cm)
14
"
max.*
(35,6
cm)
21
1
/
4
"
(54 cm)
28
15
/
16
"
(73,4 cm)
50
1
/
4
"
(127,5 cm)
5"**
(12,7 cm)
40
3
/
16
"
(102 cm)
14
"
max.*
(35,6
cm)
21
1
/
4
"
(54 cm)
28
15
/
16
"
(73,4 cm)
50
1
/
4
"
(127,5 cm)
5"**
(12,7 cm)
40
3
/
16
"
(102 cm)
27
"
INSTALLATION INSTRUCTIONS
PREVIEW INSTALLATION ORDER
NOTE
• Floor must be level, with a maximum slope of 1 inch (2.5 cm) under entire dryer. If slope is greater than 1 inch (2.5
cm), install the Extended Dryer Feet Kit. Clothes may not tumble properly, and automatic sensor cycles may not
operate correctly if dryer is not level.
• For a garage installation, you will need to place the dryer at least 18 inches (46 cm) above the floor. If using a
pedestal, you will need 18 inches (46 cm) to the bottom of the dryer.
NOTE
There should be at least a little space around the dryer (or any other appliance) to eliminate the transfer of
vibration from one to the other. If there is too much vibration, it could cause them to make noise or touch each
other causing paint damage and making even more noise.
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
14
15
Clearances (cont.)
RECOMMENDED INSTALLATION SPACING FOR CABINET INSTALLATION
• For cabinet installation with a door, minimum ventilation openings in the top of the cabinet are required.
*Required spacing
**For side or bottom venting,
2 inches (5.1 cm) spacing is allowed.
1"* (2,5 cm)
5
"**
(14 cm)
1/2
77
1/2
"
(196,8 cm)
3"* (7,6 cm)
6"*(15,2 cm)
3"* (7,6 cm)
27"
(68,6 cm)
1"
(2,5 cm)
1"
(2,5 cm)
24 in.
2*
(155 cm
2
)
48 in.
2*
(310 cm
2
)
Closet Door Vent
Requirements
Requisitos de ventilación
de la puerta del armario
(2,54 cm) (2,54 cm)
(7,6 cm)
(7,6 cm)
(7.6 cm)
(7.6 cm)
(68,6 cm)
(2.54 cm) (2.54 cm)(68.6 cm)
28
(73.4 cm)
7"* (17.8 cm)
7"* (17.8 cm)
5"*
(12.7 cm)
1"*
(2.5 cm)
(68.6 cm)
1"
(2.54 cm)
1"
(2.54 cm)
(2,54 cm) (2,54 cm)
(7,6 cm)
(7,6 cm)
(68,6 cm)
28
(73,4 cm)
7"* (17,8 cm)
7"* (17,8 cm)
5"*
(12,7 cm)
1"*
(2,5 cm)
27
"
(68,6 cm)
1"
(2,54 cm)
27
"
1"
(2,54 cm)
28
(73,4 cm)
7"* (17,8 cm)
7"* (17,8 cm)
5"*
(12,7 cm)
1"*
(2,5 cm)
(68,6 cm)
1"
(2,54 cm)
1"
(2,54 cm)
14
"
max.*
(35.6
cm)
21
1
/
4
"
(54 cm)
28
15
/
16
"
(73.4 cm)
50
1
/
4
"
(127.5 cm)
5"**
(12.7 cm)
40
3
/
16
"
(102 cm)
14
"
max.*
(35,6
cm)
21
1
/
4
"
(54 cm)
28
15
/
16
"
(73,4 cm)
50
1
/
4
"
(127,5 cm)
5"**
(12,7 cm)
40
3
/
16
"
(102 cm)
14
"
max.*
(35,6
cm)
21
1
/
4
"
(54 cm)
28
15
/
16
"
(73,4 cm)
50
1
/
4
"
(127,5 cm)
5"**
(12,7 cm)
40
3
/
16
"
(102 cm)
27
"
Leveling the dryer
w
WARNING
Failure to follow this warning can cause serious injury
or death.
Failure to follow
this warning can cause serious injury or death.
To ensure that the dryer provides optimal drying
performance, it must be level. To minimize vibration,
noise, and unwanted movement, the floor must be a
perfectly level, solid surface.
1. Position the dryer in the final location. Place a level
across the top of the dryer.
• All four leveling feet must rest solidly on the floor.
Gently push on the top corners of the dryer to make
sure that the dryer does not rock from corner to corner.
If you are installing the dryer on the optional pedestal,
you must use the leveling feet on the pedestal to
level the dryer. The dryer leveling feet should be fully
retracted.
2. Use an adjustable wrench to turn the leveling feet.
Turn clockwise to raise the dryer or counterclockwise
to lower it. Raise or lower the leveling feet until dryer
is level from side to side and front to back.
Make sure that all 4 leveling feet are in firm contact with
the floor.
Level
Leveling Feet
w
WARNING
door.
THE DRYER DOOR IS VERY LARGE AND HEAVY. Failure
to follow the instructions below can result in damage to
the dryer, property damage or injury to persons.
1. Open the door and remove the two plastic hole caps
on the catch side by gently prying up with a flat blade
screwdriver. Save these for step 6.
2. While supporting the door, remove the 4 screws, two
from each hinge. Set the door aside face down on a
protected surface to prevent damage to the door or
the work surface.
3. With the door on a protected surface, remove the 12
screws on each side of the door and lift off the inner
door frame using a flat blade screwdriver. Remove the
latch hook and blank and move them to the opposite
side.
Hole cap
Hinge screw
Inner door
frame
Latch hook
NOTE
Adjust the leveling feet only as far as necessary to
level the dryer. Extending the leveling feet more than
necessary can cause the dryer to vibrate.
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
14
15
ENGLISH
• All four leveling feet must rest solidly on the floor.
Gently push on the top corners of the dryer to make
sure that the dryer does not rock from corner to corner.
If you are installing the dryer on the optional pedestal,
you must use the leveling feet on the pedestal to
level the dryer. The dryer leveling feet should be fully
retracted.
2. Use an adjustable wrench to turn the leveling feet.
Turn clockwise to raise the dryer or counterclockwise
to lower it. Raise or lower the leveling feet until dryer
is level from side to side and front to back.
Make sure that all 4 leveling feet are in firm contact with
the floor.
4. Remove the 4 screws securing the hinges to the door
frame. Remove the two plastic cover caps. Reinstall
the hinges and cover caps on the opposite sides from
which they were removed.
5. With the hinges and cover caps in the new locations,
remount the inner door frame onto the outer door
frame with the screws removed in step 3 above.
6. Reinstall the door with the screws from step 1,2.
6. Test the swing of the door to make sure the hinges
and latch are properly aligned and that the door
closes and latches correctly.
w
WARNING
door.
THE DRYER DOOR IS VERY LARGE AND HEAVY. Failure
to follow the instructions below can result in damage to
the dryer, property damage or injury to persons.
1. Open the door and remove the two plastic hole caps
on the catch side by gently prying up with a flat blade
screwdriver. Save these for step 6.
2. While supporting the door, remove the 4 screws, two
from each hinge. Set the door aside face down on a
protected surface to prevent damage to the door or
the work surface.
3. With the door on a protected surface, remove the 12
screws on each side of the door and lift off the inner
door frame using a flat blade screwdriver. Remove the
latch hook and blank and move them to the opposite
side.
Reversing the door
Hole cap
Hinge screw
Inner door
frame
Latch hook
Hinge
assembly
Cover cap
Swing Door
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
16
17
Venting the dryer
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
• Failure to follow
these instructions can result in fire or death.
•
Failure to follow these instructions can result
in fire or death.
•
Failure to follow these instructions can result in fire or
death.
•
Failure to follow these instructions can result in fire or
death.
•
Failure to follow these instructions can result in fire or
death.
•
outside. Failure to follow these instructions can result
in fire or death.
•
Failure to follow these instructions can result
in fire or death.
•
Failure to follow these instructions can result in fire or
death.
•
dryer. Failure to follow these instructions can result in
fire or death.
•
Failure to
follow these instructions can result in fire or death.
•
Failure to follow these
instructions can result in fire or death.
•
Failure to follow these instructions can result in
fire or death.
•
Failure to
follow these instructions can result in fire or death.
•
•
In the
United States, only those foil-type flexible ducts, if any,
specifically identified for use with the appliance by the
manufacturer and that comply with the Outline for
Clothes Dryer Transition Duct, Subject 2158A, shall be
used.
Installing the side vent kit
w
WARNING
• Failure to follow all of the safety warnings in this
manual could result in property damage, injury to
persons, or death.
Your new dryer is shipped to vent to the rear.
It can also be configured to vent to the bottom or side
(right-side venting is not available on gas models).
An adapter kit, part number , may be
purchased from your LG retailer. This kit contains the
necessary duct components to change the dryer vent
location.
1. Remove the rear exhaust duct retaining screw. Pull
out the exhaust duct.
OPTION 1: SIDE VENTING
2. Press the tabs on the knockout and carefully remove
the knockout for the desired vent opening (right-
side venting is not available on gas models). Press the
adapter duct onto the blower housing and secure to
the base of the dryer as shown.
3. Preassemble a 4 inches (10.2 cm) elbow to the next
4-inches (10.2 cm) duct section, and secure all joints
with duct tape. Be sure that the male end of the elbow
faces AWAY from the dryer. Insert the elbow/duct
assembly through the side opening and press it onto
the adapter duct. Secure in place with duct tape.
Be sure that the male end of the duct protrudes 1
1
/
2
inches (3.8 cm) to connect the remaining ductwork.
Attach cover plate to the back of the dryer with
included screw.
OPTION 2: BOTTOM VENTING
2. Press the adapter duct onto the blower housing and
secure to the base of the dryer as shown.
3. Insert the 4 inche (10.2 cm) elbow through the rear
opening and press it onto the adapter duct. Be sure
that the male end of the elbow faces down through
the hole in the bottom of the dryer. Secure the elbow
in place with duct tape.
Attach the cover plate to the back of the dryer with
the included screw.
Rear
Exhaust Duct
Retaining
Screw
Elbow
Cover
Plate
Knockout
Bracket
Adapter
Duct
Bracket
Adapter
Duct
Elbow
Cover
Plate
1
1
/
2
”
(3.8 cm)
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
16
17
ENGLISH
Venting the dryer
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
• Failure to follow
these instructions can result in fire or death.
•
Failure to follow these instructions can result
in fire or death.
•
Failure to follow these instructions can result in fire or
death.
•
Failure to follow these instructions can result in fire or
death.
•
Failure to follow these instructions can result in fire or
death.
•
outside. Failure to follow these instructions can result
in fire or death.
•
Failure to follow these instructions can result
in fire or death.
•
Failure to follow these instructions can result in fire or
death.
•
dryer. Failure to follow these instructions can result in
fire or death.
•
Failure to
follow these instructions can result in fire or death.
•
Failure to follow these
instructions can result in fire or death.
•
Failure to follow these instructions can result in
fire or death.
•
Failure to
follow these instructions can result in fire or death.
•
•
In the
United States, only those foil-type flexible ducts, if any,
specifically identified for use with the appliance by the
manufacturer and that comply with the Outline for
Clothes Dryer Transition Duct, Subject 2158A, shall be
used.
Installing the side vent kit
3. Preassemble a 4 inches (10.2 cm) elbow to the next
4-inches (10.2 cm) duct section, and secure all joints
with duct tape. Be sure that the male end of the elbow
faces AWAY from the dryer. Insert the elbow/duct
assembly through the side opening and press it onto
the adapter duct. Secure in place with duct tape.
Be sure that the male end of the duct protrudes 1
1
/
2
inches (3.8 cm) to connect the remaining ductwork.
Attach cover plate to the back of the dryer with
included screw.
OPTION 2: BOTTOM VENTING
2. Press the adapter duct onto the blower housing and
secure to the base of the dryer as shown.
3. Insert the 4 inche (10.2 cm) elbow through the rear
opening and press it onto the adapter duct. Be sure
that the male end of the elbow faces down through
the hole in the bottom of the dryer. Secure the elbow
in place with duct tape.
Attach the cover plate to the back of the dryer with
the included screw.
Elbow
Cover
Plate
Bracket
Adapter
Duct
Elbow
Cover
Plate
1
1
/
2
”
(3.8 cm)
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
18
19
Venting the dryer (cont.)
ROUTING AND CONNECTING DUCTWORK
NOTE
Deduct 6 ft. (1.8 m) for each additional elbow. It is not
recommended to use more than four 90° elbows.
NOTE
Follow the guidelines below to maximize drying
performance and reduce lint buildup and
condensation in the ductwork.
Ductwork and fittings are NOT included and must be
purchased separately.
• Use 4-inch (10.2 cm) diameter rigid or semirigid
metal ductwork.
• The exhaust duct run should be as short as possible.
• Use as few elbow joints as possible.
• The male end of each section of exhaust duct must
point away from the dryer.
• Use duct tape on all duct joints.
• Insulate ductwork that runs through unheated areas
in order to reduce condensation and lint buildup on
duct surfaces.
• Incorrect or inadequate exhaust systems are not
covered by the dryer warranty. Failures or poor
performance caused by such exhaust systems will
not be covered by the dryer warranty.
Ductwork
0
1
2
3
4
0
1
2
3
4
65 ft. (19.8 m)
55 ft. (16.8 m)
47 ft. (14.3 m)
36 ft. (11.0 m)
28 ft. (8.5 m)
55 ft. (16.8 m)
47 ft. (14.3 m )
41 ft. (12.5 m)
30 ft. (9.1 m)
22 ft. (6.7 m)
Recommended
Use only for
short run
installations
INSTALLATION INSTRUCTIONS
Connecting gas dryers
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
Electrical requirements for gas models only
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
•
Failure
to follow this warning can result in fire, explosion, or
death.
•
Failure to follow this warning can result in
fire, explosion, or death.
•
Failure to follow this warning
can result in fire, explosion, or death.
•
Failure to follow this warning can
result in fire, explosion, or death.
•
Failure to follow this
warning can result in fire, explosion, or death.
•
•
Failure to follow this warning can result in fire,
explosion, or death.
•
Failure to do
so can result in fire, explosion, or death.
•
1
Failure to do so can result in fire, explosion, or death.
•
3
Failure to do so can result in fire, explosion, or
death.
•
Failure to do so can result in fire,
explosion, or death.
•
Failure to do so can result in fire,
explosion, or death.
•
Failure to
do so can result in fire, explosion, or death.
•
Failure
to do so can result in fire, explosion, or death.
• Failure to do
so can result in fire, explosion, or death.
•
Failure to follow this warning can result in
fire, explosion, or death.
•
Failure to do so can result in fire, explosion, or death.
INSTALLATION INSTRUCTIONS
4”
(10.2 cm)
4”
(10.2 cm)
2
1
/
2
”
(6.35 cm)
18
19
ENGLISH
INSTALLATION INSTRUCTIONS
Connecting gas dryers
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
Electrical requirements for gas models only
w
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
•
Failure
to follow this warning can result in fire, explosion, or
death.
•
Failure to follow this warning can result in
fire, explosion, or death.
•
Failure to follow this warning
can result in fire, explosion, or death.
•
Failure to follow this warning can
result in fire, explosion, or death.
•
Failure to follow this
warning can result in fire, explosion, or death.
•
•
Failure to follow this warning can result in fire,
explosion, or death.
•
Failure to do
so can result in fire, explosion, or death.
•
1
Failure to do so can result in fire, explosion, or death.
•
3
Failure to do so can result in fire, explosion, or
death.
•
Failure to do so can result in fire,
explosion, or death.
•
Failure to do so can result in fire,
explosion, or death.
•
Failure to
do so can result in fire, explosion, or death.
•
Failure
to do so can result in fire, explosion, or death.
• Failure to do
so can result in fire, explosion, or death.
•
Failure to follow this warning can result in
fire, explosion, or death.
•
Failure to do so can result in fire, explosion, or death.
INSTALLATION INSTRUCTIONS
20
21
Connecting gas dryers (cont.)
w
WARNING
To reduce the risk of fire, electric shock, or injury
to persons when using this appliance, follow basic
precautions, including the following:
•
Failure to do so can result in fire, explosion,
or death.
•
Failure to do so
can result in fire, explosion, or death.
•
Failure to do so can result in fire,
explosion, or death.
•
Failure to do so can result in fire,
explosion, or death.
•
Failure to do so can
result in fire, explosion, or death.
•
. Failure to follow this warning
can result in fire, explosion, or death.
• Failure to
do so can result in fire, explosion, or death.
Connecting the gas supply
1. Make sure that the gas supply to the laundry room is
turned OFF. Confirm that the type of gas available in
your laundry room is appropriate for the dryer. The
dryer is prepared for Natural Gas with a
3
⁄₈ - inch NPT
gas connection.
2. Remove the shipping cap from the gas connection
at the back of the dryer. Be careful not to damage
the threads of the gas connector when removing the
shipping cap.
3. Connect the dryer to your laundry room’s gas supply
using a new flexible stainless steel connector with a
3
⁄₈
- inch NPT fitting.
4. Securely tighten all connections between the
dryer and your laundry room’s gas supply. Turn on
your laundry room’s gas supply and check all pipe
connections (both internal and external) for gas leaks
with a noncorrosive leak-detection fluid.
Electrical connection
High-altitude installations
The BTU rating of this dryer is AGA-certified for
elevations below 10,000 feet.
If your gas dryer is being installed at an elevation above
10,000 feet, it must be derated by a qualified technician
or gas supplier.
Plug dryer into a
grounded 3-prong
outlet.
Gas Supply
Shutoff Valve
3/8” NPT Gas
Connection
1/8” NPT Pipe
Plug
AGA/CSA-Certified
Stainless Steel Flexible
Connector
INSTALLATION INSTRUCTIONS
Connecting electric dryers
w
WARNING
To help prevent fire, electric shock, serious injury,
or death, the wiring and grounding must conform
to the latest edition of the National Electrical Code,
ANSI/NFPA 70 and all applicable local regulations.
Please contact a qualified electrician to check your
home’s wiring and fuses to ensure that your home has
adequate electrical power to operate the dryer.
Electrical requirements for electric models only
w
WARNING
To reduce the risk of fire, electric shock, or injury
to persons when using this appliance, follow basic
precautions, including the following:
•
Failure to
do so can result in fire, explosion, or death.
•
Failure to follow these
instructions can result in fire, explosion, or death.
•
Failure to do so can result in fire,
explosion, or death.
•
Failure to
follow these instructions can result in fire, explosion,
or death.
•
Failure
to do so can result in fire, explosion, or death.
w
WARNING
To reduce the risk of fire, electric shock, or injury
to persons when using this appliance, follow basic
precautions, including the following:
w
WARNING
To reduce the risk of fire, electric shock, or injury
to persons when using this appliance, follow basic
precautions, including the following:
•
•
Failure to
follow these requirements can result in fire, explosion,
or death.
INSTALLATION INSTRUCTIONS
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
LG DLE1001W Le manuel du propriétaire
- Catégorie
- Sèche-linge
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: LG DLE1001W Owner's manual
Documents connexes
-
LG DLEY1201W Le manuel du propriétaire
-
LG DLEX3550V Le manuel du propriétaire
-
LG DLE2516W Le manuel du propriétaire
-
LG DLE1501W Le manuel du propriétaire
-
LG DLE3400W Le manuel du propriétaire
-
LG DLG3051W Le manuel du propriétaire
-
LG DLE5270V Le manuel du propriétaire
-
LG DLE2250W Le manuel du propriétaire
-
LG DLE4901W Le manuel du propriétaire
-
LG DLGX5681V Le manuel du propriétaire