KitchenAid KBGN292LSS0 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KBGN292LSS0

Catégorie: Barbecues

Taper: Le manuel du propriétaire

Ce manuel convient également à

InstallationInstructionsand

UseandCareGuide

27"(68.6 cm),36"(91.4 cm),39"(99.1 cm)and

48"(121.9 cm)OutdoorGrills

(Portable and Built-in -- non-combustibleconstruction)

27" (68.6 cm)

Portable without

rotisserie shown

27" (68.6 cm)

Built-In with

rotisserie shown

Models Models

KFGR270 KBGN274

KFGR274 KBGN364

KFGR292 KBGN292

KFGR364

KFGR382

IMPORTANT:

Readand save these instructions.

IMPORTANT:

Installer: Leave Installation Instructions with the consumer.

Consumer: Keep Installation Instructions for future reference.

Save Installation Instructions for local electrical inspector's use.

Write the model and serial numbers in space provided below before

installing or using outdoor grill. The numbers are stamped on the

identification label located on the underside of grill drip tray. It is also

located on the model/serial number plate, located on heat shield

behind control panel close to the smoker box.

Quick Reference

Table of Contents:

Pages

[] Before you start

[] Product dimensions

[] Built-In installation dimensions

[] Gas supply requirements

]Rotisserie electrical requirements

[] - [] Installation steps - Portable models

[] - [] Installation steps - Built-In models

[] Checking/adjusting burners

[_- [] Use and Care Information

[] - [] Grilling tips & chart

[] Rotisserie tips & chart

[_- [] Cleaning

[_ Warranty

[] - [] Requesting Assistance or Service

KitchenAid _

FOR TH E WAY IT'S MADE _

Model #

Serial #

Part No. 8285350 Rev. A

Beforeyoustart...

Your safety and the safety of

others are very important.

We have provided many important

safety messages in this manual and

on your appliance. Always read and

obey all safety messages.

1_ his is the safety alert symbol.

This symbol alerts you to

potential hazards that can kill

or hurt you and others.

All safety messages will follow the

safety alert symbol and either the word

"DANGER" or "WARNING". These

words mean:

You can be killed or seriously

injured if you don't immediately

follow instructions.

You can be killed or seriously

injured if you don't follow

instructions.

All safety messages will tell you what

the potential hazard is, tell you how to

reduce the chance of injury, and tell

you what can happen if the

instructions are not followed.

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the

appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues,

immediately call your gas

supplier or your fire

department.

FOR YOUR SAFETY

1. Do not store or use

gasoline or other

flammable vapors and

liquids in the vicinity of

this or any other appliance.

2. An L.P. cylinder not

connected for use shall not

be stored in the vicinity of

this or any other appliance.

IMPORTANT SAFETY INSTRUCTIONS

1. Do not install portable or built-in grills

in or on a recreational vehicle,

portable trailer, boat or in any other

moving installation.

2. Always maintain minimum clearances

from combustible construction, see

"Location requirements" section.

3.The outdoor cooking gas appliance

shall not be located under overhead

combustible construction.

4. This outdoor cooking gas appliance

shall be used only outdoors and shall

not be used in a building, garage, or

any other enclosed area.

5. Keep any electrical supply cord and

fuel supply hose away from any

heated surfaces.

13.When the outdoor cooking gas

appliance is not in use, the gas must

be turned off at the supply cylinder.

14. Storage of an outdoor gas grill

appliance indoors is permissible only

ifthe cylinder is disconnected and

removed from the outdoor gas grill.

15. Cylinders must be stored outdoors

and out of the reach of children and

must not be stored in a building,

garage, or any other enclosed area.

16. The pressure regulator and hose

assembly supplied with the outdoor

gas grill must be used. Replacement

pressure regulator and hose

assembly part number listed in

the "Installation Instructions" section.

6. Keep outdoor cooking and appliance

area clear and free from combustible

materials, gasoline and other

flammable vapors and liquids.

7. Do not obstruct the flow of combustion

and ventilation air. Keep the ventilation

openings of the cylinder enclosure free

and clear from debris.

8. inspect the gas cylinder supply hose

before each use of the grill. If the

hose shows excessive abrasion or

wear, or is cut, it MUST be replaced

before using the grill. Contact your

dealer and use only replacement

hoses specified for use with the grill.

9.Visually check the burner flames.

They should be blue. Slight yellow

tipping is normal for L.R gas.

10. Check and clean burner/venturi tube

for insects and insect nest.A clogged

tube can lead to fire under the grill.

11. The L.R gas supply cylinder to be

used must be:

• constructed and marked in

accordance with the Specification

for L.R Gas Cylinders of the U.S.

Department d Transportation (DOT)

or the National Standard of Canada,

CAN/CSA-B339, Cylinders, Spheres,

and Tubes for Transportation of

Dangerous Goods; and Commission.

• provided with a listed overfilling

prevention device.

• provided with a cylinder connection

device compatible with the con-

nection for outdoor grill appliances.

12. Always check connections for leaks

each time you connect and

disconnect the L.R gas supply

cylinder. See "Installation

Instructions" section.

17.The cylinder supply system must be

arranged for proper vapor

withdrawal.

18. Gas cylinder must include a collar to

protect the cylinder valve.

WARNING: If the information

in this manual is not followed

exactly, a fire causing death

or serious injury may occur.

If the following information is not

followed exactly, a fire causing death or

serious injury may occur.

• Do not store a spare LP-gas cylinder

under or near this grill.

• Never fill the cylinder beyond 80

percent full.

IMPORTANT:

This grill is manufactured for

outdoor use only.

For grills that are to be used at

elevations above 2000 feet, orifice

conversion is required. See "Gas

supply requirements" section.

It is the responsibility of the installer to

comply with the minimum installation

clearances specified on the modeltserial

rating plate. The modeltserial rating plate

can be found on the heat shield behind

control panel, close to smoker box.

Copies of the standards listed may be obtained

from:

National Fire Protection Association

One Batteryrnarch Park

Quincy, Massachusetts 02269

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

The California Safe Drinking Water and

Toxic Enforcement Act requires the

Governor of California to publish a list of

substances known to the State of

California to cause cancer, birth defects,

or other reproductive harm, and requires

businesses to warn of potential exposure

to such substances.

WARNING: This product contains a

chemical known to the State of California

to cause cancer, birth defects, or other

reproductive harm.

This appliance can cause low-level

exposure to some of the substances

listed, including benzene, crystalline silica,

carbon monoxide, toluene, and soot.

In the State of Massachusetts, the

following installation instructions apply:

• Installations and repairs must be

performed by a qualified or licensed

contractor, plumber, or gasfitter

qualified or licensed by the State of

Massachusetts.

• If using a ball valve, it shall be a

T-handle type.

•A flexible gas connector, when used,

must not exceed 3 feet.

Toolsandparts

neededfor Built-in

(non-combustible

construction)

installations

• level

• small flat-blade screwdriver

• flat-blade screwdriver

• Phillips screwdriver

• tape measure or ruler

• slip-joint pliers

• pipe wrench

• scissors or cutting pliers to remove

tiedowns

Materials required:

• gas line shutoff valve

• 1/2" male pipe thread nipple for connection

to pressure regulator

• L.R gas-resistant pipe-joint compound

• AGA or CSA design-certified outdoor

flexible stainless steel appliance connector

[4-5 ft. (1.2-1.5 m)] or rigid gas supply line

as needed

• non-corrosive leak detection solution

Partssupplied

• convertible regulator is set for 4" W.C.

natural gas.

Partsneeded

The built-in grills are manufactured for

usewith natural gas.

To convert to L.R/propane gas, Gas

Conversion Kit no. 4396311 must be

used. Follow Instructions included with kit.

Toolsandparts

neededfor Portable

installations

• level

• small flat-blade screwdriver

• flat-blade screwdriver

• Phillips screwdriver

• tape measure or ruler

• slip-joint pliers

• adjustable wrench

• scissors or cutting pliers to remove

tiedowns

Materials required:

• non-corrosive leak detection solution

Partssupplied

• hose and regulator assembly set for 11"

W.C.L.R gas (attached to manifold)

• 20 Ib. L.R tank (empty) - requires purging

and L.R gas fill by certified L.R gas fill

station

Parts needed

The portable grills are manufactured

for use with L.P./Propane gas.

To convert to Natural gas, Gas

Conversion Kit no. 4396312 must be

used. Instructions included with kit.

• To connect to a fixed L.R/propane gas

supply, you must purchase Convertible

Regulator Kit No. 4396424 from your

dealer.

Location

requirements

Explosion Hazard

Do not store fuel tank in a garage or

indoors.

Do not store grill with fuel tank in a

garage or indoors.

Failure to follow these instructions

can result in death, explosion, or fire.

Fire Hazard

Do not use grill near combustible

materials.

Do not store combustible materials

near grill.

Doing so can result in death or fire.

Select a location that provides minimum

exposure to wind and traffic paths. The

location should be away from strong draft

areas.

Do not obstruct flow of combustion and

ventilation air.

Fire Hazard

Do not install this grill on or near

combustible materials.

Doing so can result in death or fire.

If youplan to usea

combustibleenclosure,

return this unit and replace it with the

model which is manufactured for use in a

combustible enclosure.

Clearance to combustible construction

for built-in (non-combustible

construction) and portable grills:

A minimum of 12" (30.5 cm) must be

maintained between the grill hood, sides

and back and any combustible construction.

A 12" (30.5 cm) minimum clearance must

also be maintained below the cooking

surface and any combustible construction.

Rotisserie

If your model is equipped with a

rotisserie, 6" (15.2 cm) minimum

clearance on each end is needed for the

motor and skewer.

A grounded, 3-prong outlet located to the

left of the grill is required. (See "Electrical

requirements" section.)

Clearance to combustible construction for built-in (non-combustible construction) and portable grills:

A minimum of 12" (30.5 cm) must be maintained between the grill hood, sides and back and any combustible construction.

A 12" (30.5 cm) minimum clearance must also be maintained below the cooking surface and any combustible construction.

Product Dimensions

Portable and

Built-in models

(30.5urn)

30" (00.1 cm) [27" (68.6cm)grillwith

_'_ 12"(308 cm)sideburner]

48" (121.9 cm) [36"(91.4 cm)grill

with12"(30.5cm)sideburner]

_-_ 27" (68.6 urn), or

36" (91.4 urn)

side burner* I

*Not all models have side burner orside trays.

(30.5 cm)

side tray*

Fire Hazard

Do not install this grill on or near

combustible materials.

Doing so can result in death or fire.

Built-in Installation

Dimensions

(non-combustible

enclosure)

IMPORTANT:If grill is to be installed in a

combustible enclosure, return this unit and replace it

with the model which is manufacturedfor use in a

combustible enclosure.

Enclosure and clearance dimensions that are

shown must be used. Given dimensions provide

required clearances.

The installation of this grill must conform with the

currant standards CSA-Z21.58a-1998", or with

local codes.

For installations in a non-combustible enclosure,

the grill drops into the opening and is supported

by its side flanges. Do not use a bottom support.

Copies of the standards listed may

be obtained from:

* CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

12" (30.5 urn)

minimum to

counteror suppedsurfaces

musthe level

34"

86.4 cm)

36"

01.4cm) 1/2" '

portahe maleNPT 3-5/8"

models I (9.2 cm)

I I

1 i

lockingfront

casters

6" 15.2 cm

ms. cearance

for rotisserie

35-1/2"

(90.2urn)

Non-combustible enclosure installations

Grill size A 8

27" (68.6 cm) 26" (66.7 cm) 25-1/4" (64.1 cm)

36" (91.4 cm) 35" (80.5 cm) 34-1/4" (87.0 cm)

39" (99.1 cm) 38" (07.2 cm) 37-1/4" (94.6 cm)

48" (121.0 cm) 47" (119.4 cm) 46-1/4" (117.5 cm)

Gassupply

requirements

Observe all governing codes and

ordinances.

IMPORTANT: Grill must be connected

to a regulated gas supply.

• Input ratings shown on the model/serial

rating plate are for elevations up to 2,000

feet (610 m). For elevations above 2,000

feet (610 m), ratings are reduced at a

rate of 4% for each 1,000 feet (305 m)

above sea level. Orifice conversion is

required. Contact KitchenAid Assistance

Center.

• Refer to the model/serial rating plate for

information on the type of gas that can

be used. If this information does not

agree with the type of gas available,

check with your local gas supplier.

No attempt shall be made to convert

the grill from the gas specified on the

model/serial rating plate for use with a

different gas type without consulting the

serving gas supplier. The conversion

kits specified must be used.

Line pressure testing:

Testing above 1/2 psi (3.5 kPa) or

14 inches (35.5 cm) W.C. (gauge)

The grill and its individual shutoff valve

must be disconnected from the gas

supply piping system during any pressure

testing of that system at test pressures

greater than 1/2 psig (3.5 kPa).

Testing below 1/2 psi (3.5 kPa) or

14 inches (35.5 cm) W.C. (gauge) or

lower

The grill must be isolated from the gas

supply piping system by closing its

individual manual shutoff valve during any

pressure testing of the gas supply piping

system at test pressures equal to or less

than 1/2 psig (3.5 kPa).

PortableGrills

L.P.Gas:

This grill is equipped for use with a L.R

gas fuel tank. It is design-certified by CSA

International for local L.R gas supply or

for Natural gas with appropriate

conversion.

L.P.gas from a local L.P.gas supply:

IMPORTANT: The gas installation must

conform with local codes, or in the

absence of local codes, with the National

Fuel Gas Code, ANSI Z223.1/NFPA 54.

The qualified LR gas technician shall

provide the LR gas supply to the

selected grill location in accordance with

the National Fuel Gas Code, NFPA 54

and local codes.

Natural gas conversion:

Conversion must be made by a qualified

gas technician. The qualified natural gas

technician shall provide the natural gas

supply to the selected grill location in

accordance with the National Fuel Gas

Code NFPA 54 and local codes. For

conversion to Natural gas, the Natural

gas conversion kit must be used.

IMPORTANT: The gas installation must

conform with local codes, or in the

absence of local codes, with the National

Fuel Gas Code, ANSI Z223.1/NFPA 54.

To convert to Natural gas, the Natural

Gas Conversion Kit No. 4396312 must be

used, Instructions are included with the

kit.

L.P. GAS:

Operating pressure:

11 inches (27.9 cm) W.C.

Supply pressure: 11 to 14 inches

(27.9 to 35.5 cm) W.C.

NATURAL GAS:

Set pressure 4 inches (10.2 cm) W.C.

Supply pressure 7-14 inches

17.8 cm to 35.5 cm) W.C. maximum.

Built-inGrills-

non-combustible construction

Natural Gas:

Built-in grill models are equipped for use

with Natural gas. They are design-certified

by CSA International for L.R (propane or

butane) gases with appropriate

conversion.

Built-in models are set for natural gas use

and have a pressure regulator with 1/2"

female pipe threads.

The supply line shall be equipped with an

approved shutoff valve. This valve should

be located in the same area as the grill

and should be in a location that allows

ease of opening and closing. Do not block

access to the shutoff valve. The valve is

for turning on or shutting off gas to the

appliance.

shutoffvalve

gas supply._.

line

to grill

L.P.gas conversion from a local L,P. gas

supply:

Conversion must be made by a qualified

gas technician. The qualified natural gas

technician shall provide the L.R gas

supply to the selected grill location in

accordance with the National Fuel Gas

Code NFPA 54 and local codes. To

convert to L.R gas, the L.R Gas

Conversion Kit No. 4396311 must be

used. Follow Instructions included with kit.

L.P.gas conversion using a L,P.fuel tank:

To convert to L.R gas, the LR Gas

Conversion Kit No. 4396311 must be

used. Follow Instructions included with kit.

A L.R gas cylinder, not larger than 20

pounds, must be purchased separately.

NATURAL GAS:

Set pressure 4 inches (10.2 cm) W.C.

Supply pressure 7-14 inches

17.8 cm to 35.5 cm) W.C. maximum.

L.P. GAS:

Operating pressure:

11 inches (27.9 cm) W.C.

Supply pressure: 11 to 14 inches

(27.9 to 35.5 cm) W.C.

Rotisserieelectrical

requirements

Electrical Shock Hazard

Plug into a grounded 3-prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions

can result in death, fire, or

electrical shock.

If codes permit and a separate ground

wire is used, it is recommended that a

qualified electrician determine that the

ground path is adequate.

Check with a qualified electrician if you

are not sure whether the grill is properly

grounded.

Do not ground to a gas pipe.

A 120-volt, 60-Hz, AC-only, 15-ampere,

electrical supply is required.

Recommended ground method

A grounded 3-prong outdoor outlet

grounded in accordance with the National

Electrical Code ANSI/NFPA 70** or

Canadian Electrical Code (C22.1") -- and

local codes and ordinances.

3-prongpolarized

ground-typeoutdoor_.

outlet

3-prong

groundplug

power_

supplycord

Copies of the standards Iisted above may be

obtained from:

* CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

** National Fire Protection Association

One Batteryrnarch Park

Quincy, Massachusetts 02269

Installation

Instructions--

PortableOutdoor

Grill

Excessive Weight Hazard

Use two or more people to move

and install grill.

Failure to do so can result in back

or other injury.

• Move grill intodesired outdoor

location.

==Open the hood.

• For models equipped with

rotisserie, remove the rotisserie's skewer

from the grill.

• Formodels with side burners.

Remove side burner cover from the top of

the carton that is located on the grill

grate. Remove bubble wrap from side

burner cover and set aside.

Open carton located on the grill grate.

Remove side burner grate, unwrap and

set aside.

Remove burners and burner caps from

carton and unwrap. Install each set of

burners and caps inside the side burner

cavity as shown.

notch

burner

cap\

burner

> alignment

tab

Install side

burner grate cover,

and cover

(with extension

toward grill)

as shown, burner

grate

Properly dispose

of all packing

material.

• Carefully lift off grill grates and set

aside.

• Remove sear plates and set aside.

_ear plate

• Remove tiedowns from burners

and warming shelf.

_warming

shelf

remove

tiedowns

remove

tiedowns

I burner

• Reinstallsear plates. Make sure

sear plates are resting on pins.

pins

• Open cabinet doors and remove

LR/propane gas tank.

Explosion Hazard

Securely tighten all gas connections.

If connected to LP, have a qualified

person make sure gas pressure does

not exceed 11" (28 cm) water column.

Examples of a qualified person

include:

licensed heating personnel,

authorized gas company personnel,

and

authorized service personnel.

Failure to do so can result in death,

explosion, or fire.

0 • Make gas connections.

L.P./propane(supplied): The 20 lb. L.R

tank is located in the compartment below

grill. Remove tank and take to an

authorized dealer to be filled. Reinstall

tank and screw the hose/regulator

assembly to tank as shown.

The pressure

regulator and

hose assembly

supplied with

the grill must

be used.

Replacement

pressure

regulator and hose assembly specific to

your model, is available from your outdoor

grill dealer.

If converting to natural gas, see

conversion kit requirements and "Gas

supply requirements" section. Follow

instructions included with kit.

1. Turn on the gas supply. Wait a

few minutes for gas to move through the

gas line.

2, Test all connections by brushing

on an approved non-corrosive leak-

detection solution. Bubbles will show a

leak. Correct any leak found.

3. Go to "Checking and adjusting

the burners" section.

If convertedto

NaturalGas

NaturalGasUse

This installation must conform with local

codes and ordinances**. In the absence of

local codes, installations must conform with

either the National Fuel Gas Code ANSI

Z223.1, or CANtCGA-B149.1 * Natural Gas

and Propane installation code.

• Open shutoff valve in the gas

supply line. The valve is open when the

handle is parallel to the gas pipe.

Test all connections by brushing on an

approved non-corrosive leak-detection

solution. Bubbles will show a leak. Correct

any leak found.

valve_ee

Explosion Hazard

Use a new AGA or CSA approved

"outdoor" gas supply line.

Securely tighten all gas connections.

Failure to do so can result in death,

explosion, or fire.

• Make gas connections.

A combination of pipe fittings must be

used to connect the grill to the existing

gas line.

• If local codes permit, use an outdoor

flexible stainless steel tubing gas

connector, design-certified by AGA or

CSA International, to connect the grill to

the rigid gas supply line. 5/8" diameter

line is recommended. Using a wrench to

tighten, connect the gas supply to the

grill. Use pipe joint compound on all non-

flared male threads. Do not kink or

damage the flexible connector when

moving the grill.

• Pipe-joint compounds suitable for use

with L.R gas must be used. Do not use

Teflon_'tape.

rear of 1/2" g.rill

grill

flexiblegas

connector

Copies of the standards iisted may

be obtained from:

*CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

** for local codes, contact your local

building inspector

@Teflon is a registered trademark of E.I. Du Pont

8 de Nemours and Company.

Installation

Instructions--

Built-In Outdoor

Grill

(non-combustible

construction)

Fire Hazard

Do not install this grill on or near

combustible materials.

Doing so can result in death or fire.

IMPORTANT: If grill is to be installed in a

combustible enclosure, return this unit

and replace it with the model which is

manufactured for use in a combustible

enclosure.

Fire Hazard

Do not use grill near combustible

materials.

Do not store combustible materials

near grill.

Doing so can result in death or fire.

Excessive Weight Hazard

Use two or more people to move

and install grill.

Failure to do so can result in back

or other injury.

NaturalGasUse

This installationmust conform with local

codas and ordinances**. In the absence of

local codes, installations must conform

with either the National Fuel Gas Code

ANSI Z223.1, or CAN/CGA-B149.1 *

Natural Gas and Propane installation coda.

• Place grill into outdoor enclosure,

but leave enough room in back to connect

to gas supply.

Explosion Hazard

Securely tighten all gas connections.

If connected to LP, have a qualified

)erson make sure gas pressure does

not exceed 11" (28 cm) water column.

Examples of a qualified person

include:

licensed heating personnel,

authorized gas company personnel

and,

authorized service personnel.

Failure to do so can result in death,

explosion, or fire.

• Make gas connections.

A combination of pipe fittings must be

used to connect the grill to the existing

gas line.

• If local codes permit, use an outdoor

flexible stainless steel tubing gas

connector, design-certified by AGA or

CSA International, to connect the grill to

the rigid gas supply line. 5t8" diameter

line is recommended. Using a wrench to

tighten, connect the gas supply to the

grill. Use pipe joint compound on all non-

flared male threads. Do not kink or

damage the flexible connector when

moving the grill.

• Pipe-joint compounds suitable for use

with L.R gas must be used. Do not use

Teflon_>tape.

rear el 1/2" g.rill

grill

flexiblegas

connector

Copies of the standards iisted may

be obtained from:

*CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

** for local codes, contact your local

building inspector

• Open shutoff valve in the gas

supply line. The valve is open when the

handle is parallel to the gas pipe.

valve Ken

• Test all connections by brushing

on an approved non-corrosive leak-

detection solution. Bubbles will show a

leak. Correct any leak found.

• Open the hood.

• For models equipped with

rotisserie, remove the rotisserie's skewer

from the grill.

• Formodels with side burners.

Remove side burner cover from the top of

the carton that is located on the grill

grate. Remove bubble wrap from side

burner cover and set aside.

Open carton located on the grill grate.

Remove side burner grate, unwrap and

set aside.

Remove burners and burner caps from

carton and unwrap. Install each set of

burners and caps inside the side burner

cavity as shown.

notch

burner

cap _ /

bure_

Install side

burner grate cover,

and cover

(with extension

toward grill)

as shown, burner

grate

Properly dispose

of all packing

material.

@Teflon is a registered trademark of E.I. Du Pont

de Nemours and Company.

==Carefully lift grill grates off of grill

area and set aside.

==Remove sear plates and set aside.

searplate

0 • Remove tiedowns from burners

and warming shelf.

_warming

shelf

remove J

Uedowos

remove

tiedowos

I burner

1 • Reinstall sear plates. Make

sure sear plates are resting on pins.

If convertedto

L.P.Gas

Explosion Hazard

Securely tighten all gas connections.

If connected to LP, have a qualified

)erson make sure gas pressure does

not exceed 11" (28 cm) water column.

Examples of a qualified person

include:

licensed heating personnel,

authorized gas company personnel

and,

authorized service personnel.

Failure to do so can result in death,

explosion, or fire.

• Make gas connections.

L,P./propane(supplied): The 20 lb. L.R

tank is located in the compartment below

grill. Remove tank and take to an

authorized dealer to be filled. Reinstall

tank and screw the hose/regulator

assembly to tank as shown.

The pressure

hose/regulator

regulator and assembly

hose assembly f

supplied with the

grill must be used.

Replacement

pressure regulator

and hose

assembly specific to your model, is

available from your outdoor grill dealer.

If converting to natural gas, see

conversion kit requirements and "Gas

supply requirements" section. Follow

instructions included with kit.

==Turn on the gas supply. Wait a few

minutes for gas to move through the gas

line.

• Test all connections by brushing on

an approved non-corrosive leak-detection

solution. Bubbles will show a leak. Correct

any leak found.

= Go to "Checking and adjusting the

burners" section.

2 • Carefully slide grill completely

into outdoor enclosure.

3 • Now go to the "Checking and

Adjusting Burners Section."

Checkingand

adjustingthe

burners

The burners are tested and factory-set for

most efficient operation. However,

variations in gas supply and other

conditions may make minor adjustments

to air shutter or low flame setting

necessary. Adjustments must be done by

a qualified service technician.

NOTE: No adjustment can be made to

the infrared rotisserie burner (not used on

all models) or smoker tray burner(s).

Checking and adjusting the grill burner

flames requires removing the grate and

sear plates.

Sear burnerflame characteristics:

The flames of the grill burners and

surface burners (not used on all models)

should be blue and stable with no

excessive noise or lifting (L.Rtpropane

gas flames will have a slightly yellow tip).

A yellow flame indicates not enough air.

If flame is noisy or lifts away from the

burner, there is too much air. Some

yellow tips on flames when the burner is

set to HI setting are acceptable as long

as no carbon or soot deposits appear.

Check that burners are not blocked by

dirt, debris, insect nests, etc. and clean

as necessary. If they are clean, adjust air

shutters as needed.

IMPORTANT: Before adjusting air

shutters, let burners cool down.

Adjusting the air shutters:

1. Lightgrill using information in the

"Lighting the grill" section.

2. Observe flame to determine which

burners need adjustment and how the

flame is acting, See "Sear burner

flame characteristics" above.

3. Turn offthe valve and wait until grill

and burners are cool.

4. Remove grill grates, sear plates.

5. Remove burner and loosen air shutter

adjustment screw.

a. If flame is yellow (not enough air),

turn air shutter counter-clockwise.

b. ff flame is noisy or lifts away from

burner (too much air), turn air

shutter clockwise.

Adjustment should be from 1/8" to 1/4".

airshutter

adjustmentscrew

6. Tighten air shutter adjustment screw.

7. Replace burner sear plates and grates.

8. Ignite burner to check flames. See

"Sear burner flame characteristics."

Repeat Steps 1 through 8 above if needed.

Only adjust the burners that need

adjustment.

Low flame adjustment:

If flame goes out on the "LO" setting, the

low flame setting must be adjusted.

1. Turn offthe valve and wait until grill

and burners are cool.

2. Remove grill grates, sear plates.

3. Light grill using information in the

"Lighting the grill" section.

4. Turn burner to its lowest setting and

remove knob.

5. Hold valve stem with pliers and insert a

thin flat-blade screwdriver intothe shaft.

6. Watch the flame and slowly turn the

screwdriver counter-clockwise.

7. Adjust flame to minimum stable flame.

valves_

8. Replace the control knob and turn off

the burner.

9. Repeat Steps 3 through 8 for each

burner if needed.

10, Replace the sear plates and grates

after the burners have cooled.

GrillUse

Explosion Hazard

Do not store fuel tank in a garage

or indoors.

Do not store grill with fuel tank in a

garage or indoors.

Failure to follow these instructions

can result in death, explosion, or fire.

Fire Hazard

Do not use grill near combustible

materials.

Do not store combustible materials

near grill.

Doing so can result in death or fire.

Food Poisoning Hazard

Do not let food sit for more than

one hour before or after cooking.

Doing so can result in food

poisoning or sickness.

Using your grill

Prepare the gas supply

1. Open the hood completely. Do not light

burners with the hood closed.

2. Make sure

control knobs are

turned to OFR

The drip pan

must be in place

and pushed all

the way to the

back.

Turn the gas supply on:

1. For portable grills using an L.R/

propane gas cylinder:

Slowly open the cylinder valve; do not

"snap" open.

NOTE: If flow limiting device does

activate, your grill may not light. If your

grill does light, the flames will be low

and will not heat properly. Turn cylinder

valve and ell control knobs off and wait

30 seconds. After shutting off the

cylinder, very slowly open cylinder

valve and wait 5 seconds before

lighting.

2. For grills using gas supply source other

than L.P.gas cylinder:

Turn the shut off valve to open position

from the front of gas supply line.

Lighting the grill

red button

drill burner

controlknob

smoker burner

tray ignitor

bnUon

infrared

bnroor

control smokertrey

knob burner

controlknob

grillburner

controlknob

ignitorbeflery

compartment

IMPORTANT:Light only one burner at a

time.

Do not lean over burners. Push in and

turn to "LITE" the control knob for the

burner you wish to use.

Push in the burner ignitor button. You

will hear the "snapping" sound of the

spark. Keep the burner ignitor button

pushed in until burner lights. Make sure

burner is lit, Repeat for each of the

other burners as needed.

IMPORTANT:

If burner does not light immediately,turn the

burner knob to "OFF" and wait 5 minutes

before relighting.

Manuallylighting main grill burners

1. Remove the manual lighting extension

from inside the drip tray.

2. Attach e match to the clip.

4. Carefully guide the lit match between

the grill grate and one of the slots in

the sear plate.

5. Push in and turn the burner knob to

"LITE" for the burner closest to the lit

match. The burner will light immediately.

6. Repeat steps 2 through 5 for each

main burner.

7. Replace manual lighting extension

inside the drip tray.

IMPORTANT:

If burner does not light immediately,turn the

burner knob to "OFF" and wait 5 minutes

before relighting.

If any burnersdo not light after attempting

to manually light them, contact the

KitchenAid Assistance Center.

Using the side burner

Burn Hazard

Do not let the burner flame extend

beyond the edge of the pan.

Doing so can result in burns.

Remove side burner cover. Do not light

burners with the cover on.

Lighting the side burner

IMPORTANT:Light only one burner at a

time.

Do not lean over burners. Push in and

turn to "LITE" the control knob for the

burner you wish to use.

Push in the burner ignitor button. You

will hear the "snapping" sound of the

spark. Keep the burner ignitor button

pushed in until burner lights. Make sure

burner is lit. Repeat for the other

burner as needed.

IMPORTANT:

If burner does not light immediately,turn the

burner knob to "OFF" and wait 5 minutes

before relighting.

12 3. Strike the match to light it.

Manuallylighting the burners

1. Use a paper match to light the burners.

2. Push in and turn the burner knob to

"LITE" for the burner closest to the lit

match. The burner will light immediately.

IMPORTANT:

If burner does not light immediately,turn the

burner knob to "OFF" and wait 5 minutes

before relighting.

If any burnersdo not light after attempting

to manually light them, contact the

KitchenAid Assistance Center.

Using the rotisserie

motor rotisserie backinfrared burner

For best cooking results, do not use main

grill burners when using the rotisserie.

The rotisserie system is designed to cook

food from the rear using intense, searing

infrared heat.

1. Remove warming shelf.

2. Mount rotisserie motor on the grill's

mounting bracket. Position it securely

into support bracket slots.

3.To load the spit rod, slide one of the

rotisserie forks onto the spit rod with

prongs facing away from handle.

4. Push spit rod through the center of the

food, then slide second rotisserie fork

into position.

5. Center the food and rotisserie forks on

spit rod and tighten wing nuts on the

rotisserie forks. If necessary, secure

loose food portions with butcher's

string only. Never use nylon or plastic

string which will melt and ruin the food.

6. Once the food is positioned on spit rod,

place pointed end of rod into rotisserie

motor and lower spit rod onto supports

at either side of the grill.

IMPORTANT: On Models KFGR292LSS,

KFGR382LSSand

KBGN292LSS,remove

the handlefromthespit

rodwhenusingtheside

burner.The handlewill

get"HOT"andfailureto

removeit willcausethe

handletocrackand

melt.

remove

handle

7. Plug single-prong plug into rotisserie

motor.

Electrical Shock Hazard

Plug into a grounded 3-prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions

can result in death, fire, or

electrical shock.

8. Plug 3-prong plug into a grounded

3-prong outlet.

To avoid product damage when not using

the rotisserie, remove motor and store

indoors. Remove spit rod and forks. Store

out of reach of children.

Lighting the infrared

(rotisserie) burner

1. Push in and turn rotisserie burner knob

to "LITE".

2. At the same time, push in both red

button (left hand side) and burner

ignitor button (right hand side). You will

hear a "snapping" sound.

3. When infrared burner lights, release

the burner ignitor button but continue

pressing the red button for another 5 to

10 seconds.

IMPORTANT:

If the rotisserie burner does not light

immediately, turn the burner knob to "OFF",

wait 5 minutes before relighting.

Manuallylighting infrared burner

1. Remove the manual lighting extension

from inside the drip tray.

2. Attach a match to the clip.

3. Strike the match to light it.

4. Carefully hold the lit match close to the

infrared burner.

5. Push in and turn the infrared burner

control knob to "LITE".

6. Push in the red button above the

infrared burner control knob, the burner

will light immediately. Hold this button

in for 5 to 10 seconds.

7. Repeat steps 3 through 6 for each

infrared burner. (Number of infrared

burners varies by model.)

8. Replace manual lighting extension

inside the drip tray.

IMPORTANT:

If the infrared burner does not light

immediately, turn the infrared burner

control knob to "OFF" and wait 5 minutes

before relighting.

Using the smoker box(es)

Burn Hazard

Do not remove the smoker box

when grill is hot.

Doing so can result in burns.

Your grill may have one or two slide-out

smoker boxes that can be used with the

main grill burners or the rotisserie.

The smoker trays are designed for easy

use. After deciding which wood chips to

use, follow the instructions on wood chip

packaging. Small size chips or pellets are

recommended.

Slide box and chip cover out of smoker

compartment, chipcover

Remove cover _

from box. Turn

cover over and

fill with

prepared

chips.

Turn smoker box over and place over

chip cover. Hold cover and box together

and turn right side up.

Slide box and cover back into smoker

compartment.

Light the smoker burner(s) 5 minutes

ahead of time to start them smoking. The

specially-designed smoker will smoke the

food while the grill burners or rotisserie

cooks it. Keeping the hood closed as

much as possible will maximize the

smoking effect. 13

Manuallylightingsmokerburner

1. Remove smoker tray.

2. Remove the manual lighting extension

from inside the drip tray.

3. Attach a match to the clip.

4. Strike the match to light it.

5. Carefully guide the lit match into the

smoker chamber area where the tray

was removed.

6. Push in and turn the knob for the

smoker burner to "LITE", the burner will

light immediately.

7. Replace smoker tray.

8. Repeat steps 1 through 6 for each

smoker burner. (Number of smoker

burners varies by model.)

9. Replace manual lighting extension

inside the drip tray.

IMPORTANT:

If the smoker burner does not light

immediately, turn the burner knob to "OFF",

wait 5 minutes before relighting.

Always allow box to cool before removal

or cleaning.

Grill Care

Replacing the ignitor battery

Your model may have one or two ignitor

batteries. If ignitors stop sparking, the

battery (or batteries) should be replaced.

1. Lift up at bottom of battery tray and

slide battery tray out.

lift upand

Jslide outtray

2. Remove battery (or batteries) and

replace with alkaline 9-volt battery (or

batteries).

3. Slide battery tray back into

compartment.

GrillingTips

Food Poisoning Hazard

Do not let food sit for more than

one hour before or after cooking.

Doing so can result in food

poisoning or sickness.

Before Grilling

• Thaw food items before grilling.

• Preheat grill on high (use all grill

burners) 7-10 minutes. The hood must

be closed during preheating. Do not use

back infrared burner for preheating.

Preheating provides the high heat

needed to brown and seal the juices.

• Shorten the preheat time when grilling

high-fat cuts of meat or poultry, such as

chicken thighs. This will help reduce

flare-ups.

• Lightly oil the grill or the food when

cooking low-fat cuts of meat, fish or

poultry, such as lean hamburger patties,

shrimp or skinless chicken breasts.

• Too much oil can cause gray ash to

deposit on food.

• Trim excess fat from meats prior to

cooking to prevent flare-ups.

• Make vertical cuts at 2" intervals around

the fat edge of meat to help prevent the

meat from curling while cooking.

• Add seasoning or salt only after the

cooking is finished.

During Grilling

• Turn foods only once. Juices are lost

when meat is turned several times.

• Turn meat just when juices begin to

appear on the surface.

• Avoid puncturing or cutting the meats to

test doneness. This allows juices to

escape.

• It may be necessary to lower the heat

setting for foods that cook a long time or

are marinated or basted in a sugary

sauce.

• If using a high flame, add barbecue

sauce only during the last 10 minutes of

cooking to avoid burning the sauce.

• The degree of doneness is influenced

by the type of meat, cut of meat (i.e.

size, shape and thickness), heat setting

selected, and length of time on the grill.

• With the grill cover open the cooking

time will be longer.

Smoker Box

The smoker box is a tray that holds wood

chips or pellets that provide a smoky

flavor when foods are cooked on the grill

or rotisserie. For best results the hood

should be down for most of the cooking

time.

• The amount and size of chips and

length of cooking time determine the

degree of smoke flavor.

• When using wood chips or wood pellets

always follow the package directions.

For increased smoking, soak chips in

water prior to placing in the smoker box.

Guide to Wood Chips or Pellets:

Alder: A medium, tart smoke taste.

Superb on salmon and other fish, chicken

or game.

Maple: Sweet, hearty smoke flavor. Best

with fish, jerky or bacon.

Apple: A light, sweet flavor. Superb with

poultry, ham or sausage.

Hickory: Heavy smoke flavor. Best with

beef, pork or game.

Mesquite: A light smoke flavor. Best with

fish, poultry or beef.

Oak: Heavy smoke flavor. Best with beef,

lamb or pork.

Pecan: A rich, sweet, versatile flavor.

Can be used with anything.

Grapevine: A strong smoke flavor. Best

with beef or poultry.

CookingMethods

Direct Heat

Cooking by Direct Heat means the food is

placed on grill grates directly above

lighted burners. Hood position affects total

cooking time.

Direct Heat sears the food. Searing is a

process that seals natural juices in food

by cooking with intense heat for a short

period of time. While juices stay inside,

the outside is browned with a flavorful

grilled coating.

Indirect Heat

For best results, do not select the Indirect

Heat cooking method when it is windy.

Cooking by indirect Heat means the food

is placed on the grill grate above an

unheated burner, allowing heat from

lighted burner(s) on either side to cook

the food.

If possible, turn on two burners. Cook

with the hood down. This will shorten the

cooking time.

Indirect Cooking

Place food only on the grill grate over the

OFF burners.

Burner

1 2 3 4

27" grill ON OFF -- --

36" grill ON OFF ON --

GrillingChart

• Knobs have High, Medium and Low setting for flame adjustment.

• Heat settings indicated are approximate.

• Grilling time based on heating two adjacent burners with food

placed on grate between burners (Direct).

• Timings are affected by weather conditions.

Beef

• Remove excess fat from edge of chops and steaks. Score

remaining fat at 2-inch intervals to prevent curling.

• When 2 temperatures are provided, example: Medium to

Medium-Low, start with the first and adjust to how it is cooking.

• Cooking times may vary from chart times depending on the type

of fuel, natural gas or L.R.

Hamburgers DIRECT Medium (160°F) Grill, turning once.

1/2 to 3/4 inch thick Medium 10-15 minutes total

Roasts

Rib Eye, Sirloin INDIRECT Med-Rare (145°F) to Medium (160°F) Tent with foil first 45-60 minutes

Medium/OFF/Medium 3240 minutes per lb. of cooking time.

Steaks

Porterhouse, Rib DIRECT Med-Rare (145°F) to Medium (160°F) Rotate steaks 1t4 turn to create

T bone, Top Loin Medium 11-16 minutes total criss-cross grill marks.

Sirloin

1 inch

Porterhouse, Rib DIRECT Med-Rare (145°F) to Medium (160°F)

T bone, Top Loin Medium 18-25 minutes total

Sirloin

1-1t2 inch

Top Round or DIRECT Med-Rare (145°F) to Medium (160°F)

Shoulder/Chuck Medium 22-29 minutes total

(London Broil)

1-1t2 inch thick

Flank DIRECT Med-Rare (145°F)

1/2 inch thick Medium 11-16 minutes total

Pork

Chops, 1 inch thick DIRECT Medium (160°F)

Medium to Med-Low 12-20 minutes total

1-1/2 inch thick DIRECT Medium (160°F)

Medium to Med-Low 30-40 minutes total

Ribs INDIRECT Medium (160°F) Grill, turning occasionally. During last few

2-1/2 to 4 Ibs. Med/OFF/Med 40-60 minutes total minutes brush with barbecue sauce if

desired. When done, wrap in foil 1 hour.

Roast. Boneless DIRECT Medium (160°F) Turn during cooking to brown on all sides.

Tenderloin 1 Ib Medium 18-22 minutes total

Ham, Half INDIRECT Reheat (140°F) Wrap entire ham in foil and put on grill

8 to 10 Ibs. Med/OFF/Med 2 - 2-1/2 hours total without pan or drip pan.

Ham Steak DIRECT Reheat (140°F)

Precooked Preheat Medium 7-10 minutes total

1/2 inch thick Grill Medium

Hot Dogs DIRECT Reheat (145°F) Slit skin if desired.

Medium 5-10 minutes total

Chicken

Breast DIRECT (170°F) For even cooking, pound to 3/4 inch.

Boneless Medium 15-22 minutes total

Pieces DIRECT breast (170°F) Start bone side down.

2 to 3 Ibs. Med-Low to Medium thigh (180°F)

18-25 minutes total

Lamb

Chops and Steaks DIRECT Med-Rare (145°F) to Medium (160°F)

Loin, Rib, Sirloin Medium 10-20 minutes total

1 inch thick

1-1/2 inches thick DIRECT Med-Rare (145°F) to Medium (160°F)

Medium 16-20 minutes total

Fish And Seafood

Fillets, Steaks, Chunks DIRECT 4-6 minutes per each Grill, turning once. Brush grill with oil to

Halibut, Salmon, Swordfish Medium 1/2 inch thickness of fish keep from sticking. Remove when inside is

8 oz. opaque and flaky with skin easily removed.

Whole DIRECT 5-7 minutes per side Grill, turning once. Brush grill with oil to

Catfish, Rainbow Trout High keep from sticking. Remove when inside is

8 - 11 ounces opaque and flaky with skin easily removed.

Shellfish, DIRECT 4-8 minutes total

Scallops, Medium

Shrimp

Turkey

Whole Breast INDIRECT (170°F) Tent with foil until last 30 minutes of

(bone-in) HI/OFF/HI 14-18 minutes per lb. cooking time.

One Half Breast INDIRECT (170°F) Start skin side down.

(bone-in) Medium/OFF/Medium 25-30 minutes per lb.

Whole INDIRECT breast (170°F) Less than 11 pounds.

7 to 12 lb. HI/OFF/HI thigh (180°F)

11-16 minutes per lb.

Fresh Vegetables

Corn on the cob DIRECT 20-25 minutes total Soak in cold water 20 min. Do not husk.

Medium Shake off excess water.

Eggplant DIRECT 7-10 minutes total Wash & cut into 1/2 inch slices or

Medium lengthwise. Brush with olive oil.

Onion, 1/2 inch thick DIRECT 8-20 minutes total Grill, turning once. Brush with olive oil.

Medium Put a skewer through several slices to

hold together.

Potatoes

Sweet, whole DIRECT 40-70 minutes total Wrap individually in heavy-duty foil.

Medium Grill, rotating occasionally.

Baking, whole High 45-90 minutes total

Peppers, roasted DIRECT 15-22 minutes total Wash and place on grill whole. Char skin

High all around. Cool in a paper bag or plastic

wrap to loosen blackened skin. Peel and

remove seeds.

Squash, summer DIRECT 7-10 minutes total Wash & cut into 1/2 inch slices or

Zucchini Medium lengthwise. Brush with olive oil.

Roasted Garlic DIRECT 20-25 minutes total Cut off top, drizzle with olive oil end

Medium wrap in double layer of foil.

Rotisserie

CookingTips

Food Poisoning Hazard

Do not let food sit for more than

one hour before or after cooking.

Doing so can result in food

poisoning or sickness.

(Rotisserie available on some models)

Rotisserie cooking rotates food in front

of an infrared burner, creating an intense

heat for searing the outside and sealing

in natural juices.

• The infrared burner reaches cooking

temperatures in about one minute. Do

not preheat when using the rotisserie.

• Select tender meat and poultry.

Allow at least 1 inch space between

infrared burner and the food.

• Rotisserie can be used in combination

with the smoker and/or the grill.

RotisserieChart

• To make cleanup easier, place a pan

under the food to catch drippings.

• The cover can be opened or closed,

but when using the rotisserie with the

smoker the cover should be closed.

• Add barbecue sauce or glaze only

during the last 10 minutes of cooking

to prevent sauce from burning.

Trussing Poultry for the Rotisserie

1. Load the spit rod by sliding one of the

forks on the rod, with the prongs facing

away from the rod handle. Tighten the

screw to keep it from slipping.

2. Push the rod through the center of the

bird.

3. Cut 24" of kitchen twine and center it

under the bird, breast side up.

4. Wrap each end of the twine around the

wings; catch each wing tip. Bring the

twine tightly together at the top of the

breast and knot. Do not cut off the

extra twine.

5. Cut another 20 inches of string and lay

it under the back of the bird. Wrap it

around the tail then around the spit rod,

cinching tightly.

6. Cross the legs on top of spit rod; tie

twine around the crossed legs.

7. Connect the twine holding the legs to

the twine holding the wings and knot.

Cut off any bits of hanging twine.

8. Slide the second fork pushing the tines

into the drumsticks.

9. Center the food and forks on the rod

and tighten the thumbscrews. The bird

should not rotate or be loose in any

way.

• Use a portable meat thermometer to check internal doneness of the item.

• Turn off rotisserie burner when meat thermometer reads 5°F lower than desired

internal temperature. Continue rotating, hood closed, for 10 minutes before carving.

• Timing is affected by weather conditions such as wind and outside temperature.

Beef

Roasts 4-6 Ibs. Med-Rare (145°F) 15-20 min. per lb.

Rib Eye Medium (160°F) 20-25 min. per lb.

Sirloin Tip

Rib, boneless

Poultry

Chicken 3-6 Ibs. breast (170°F) 25-30 min. per lb.

thigh (180°F)

Turkey, whole 7-10 Ibs. breast (170°F) 11-20 min. per lb.

thigh (180°F)

Lamb

Boneless Leg 4-7 Ibs. Medium (160°F) 20-25 min. per lb.

Pork

Loin roast, 4-6 Ibs. Medium (160°F) 20-23 min. per lb.

boneless

Cleaning

General Cleaning

IMPORTANT: Before cleaning, make sure

all controls are off and the grill is cool.

Always follow label instructions on

cleaning products.

For routine cleaning, wash with soap end

water using a soft cloth or sponge. Rinse

with clean water and dry at once with a

soft, lint-free cloth to avoid spots end

streaks.

Never use steel wool to clean the grill, as

it will scratch the surface.

Use vinyl grill cover, available from

your local dealer, to protect finish from

weather. See "Accessories" section.

Stainless Steel

IMPORTANT: Do not use soap-filled

scouring pads, abrasive cleaners,

Cooktop Polishing Creme, steel wool,

gritty wash cloths or paper towels.

Cleaners should not contain chlorine.

Damage may occur.

Rub in direction of grain to avoid

scratching or damaging the surface.

Food spills should be cleaned as soon as

entire grill is cool. Spills may cause

permanent discoloration.

• Use Stainless Steel Cleaner & Polish

(Part No. 4396095). See "Requesting

Assistance or Service" section to order.

• Use a mild liquid detergent or all-

purpose cleaner according to label

instructions.

• Rinse with clean water and dry at once

with soft, lint-free cloth to avoid spots

and streaks.

• Use vinegar to remove hard water

spots. Rinse with water and dry

thoroughly.

• Use a glass cleaner to remove

fingerprints.

Grill grates

IMPORTANT: Never use a steel or fiber

scraper on grill grates.

Immediately after you are finished

cooking, loosen food soil with a brass

bristle brush. Turn all burners to "HI" for

10-15 minutes with the hood closed to

burn off food soil. Turn off all burners,

raise the hood and let grates cool. Use

the brass bristle brush to remove ash

from the grill grates.

When completely cool, grill racks can be

removed for thorough cleaning. Clean

them with e mild detergent and warm

water.

For baked-on soil, prepare a solution of

1 cup (250 mL) ammonia to 1 gallon

(3.75 L) water. Soak grates for 20

minutes, then rinse with water and dry

completely.

Warming Shelf

• Use a mild liquid detergent (such as a

dish detergent) or an all-purpose

cleaner, following the label instructions.

Rinse with clean water end dry with soft,

lint-free cloth.

• For tough spots or baked-on grease, use

Whirlpool Degreaser (Part No. 31552), a

commercial degreaser designed for

stainless steel. See "Requesting

Assistance or Service" section to order.

IMPORTANT: Make sure gas supply is off

and all control knobs are in the "OFF"

position. Make sure the Side Burner is

cool.

Exterior

The quality of this material resists most

stains and pitting, providing that the

surface is kept clean and protected.

• Apply stainless steel polish to all non-

cooking areas before first use. Re-apply

after each cleaning to prevent

permanent damage to surface.

• Cleaning should always be followed by

rinsing with clean warm water.

• Wipe the surface completely dry with a

soft cloth.

• For tough spots or baked-on grease, use

Whirlpool Degreaser (Part No. 31552), a

commercial degreaser designed for

stainless steel. See "Requesting

Assistance or Service" section to order.

Interior

Discoloration of stainless steel on these

parts is to be expected, due to intense

heat from the burners.

• Cleaning should always be followed by

rinsing with clean, warm water.

• Use a mild liquid detergent or all-

purpose cleaner, following label

instructions. Rinse with clean water and

dry completely with a soft, lint-free cloth.

• A heavy-duty scrub sponge can be used

with mild cleaning products. Always rub

in the direction of the grain.

• For small, difficult-to-clean areas, use

Whirlpool Degreaser (Part No. 31552), a

commercial degreaser designed for

stainless steel. See "Requesting

Assistance or Service" section to order.

Side burner caps and grate

• Clean with a brass bristle brush.

• Wash grate using mild detergent, warm

water and degreaser.

• Rinse with clean water and dry with soft,

lint-free cloth.

• Use Stainless Steel Cleaner & Polish

(Part No. 4396095). See "Requesting

Assistance or Service" section to order.

U-shaped burners

* Clean the exterior of the burner with a

wire brush.

* Clear any clogged burner ports with a

straightened paper clip. Never use a

toothpick as it may break off end clog

the port.

* Use a flashlight to inspect into the

burner through the burner inlet to

ensure there is no blockage. If any

obstruction is seen, use a metal coat

hanger that has been straightened to

clear them.

After inspecting the inside of burner for

blockage, reassemble burner by sliding

the middle tube of burner over orifice.

Insert tabs on the burner bracket into the

holes in burner support.

burnerbracket

orifice

burnersupport

Drip tray

IMPORTANT:The drip tray should only be

removed when grill is completely cool.

The full-width drip tray collects grease

and food particles that fall through the

grill. Remove tray and set on a flat

surface.

• Wipe excess grease with paper towels.

• Use mild detergent, warm water. Rinse

and dry thoroughly. Replace tray.

• Clean often to avoid grease build-up.

Smoker box

Burn Hazard

Do not remove the smoker box

when grill is hot.

Doing so can result in burns.

IMPORTANT:After cooking let the grill

and smoker box cool completely before

cleaning.

• Remove box by sliding it forward.

Discard ashes.

• Wash box using a mild liquid detergent

or all-purpose cleaner, following the

label instructions. Rinse with clean water

and dry with soft, lint-free cloth. Replace

box.

• Color of smoker box and cover will be

altered due to heat generated by the

burners and smoking wood chips.

Knobs, plastic and flange area

around knobs

IMPORTANT: Do not use steel wool,

abrasive cleaners, or oven cleaner.

Do not soak knobs.

• Wash with mild detergent, using a soft

cloth and warm water. Rinse and dry.

Control panel graphics

IMPORTANT:Do not use steel wool,

abrasive cleaners or oven cleaner.

Do not spray cleaner directly onto panel.

Clean around the burner labels gently;

scrubbing may remove printing.

• Wash with mild detergent, using a soft

cloth and warm water. Rinse and dry.

Rotisserie spit rod handle

(On some models)

• Do not use steel wool, abrasive cleaners

or oven cleaner.

• Wash with mild detergent, using a soft

cloth and warm water. Rinse and dry.

Rotisserie spit rodand forks

(On some models)

• Wash with mild detergent, using a soft

cloth and warm water. Rinse and dry.

• For stubborn areas, use a multi-purpose

cleaner, a heavy-duty scrub sponge or

mild abrasive cleaner.

Accessories

CustomAccess Door Kits are

available from your dealer.

27" (68.6 cm): Door Kit No. 4396314

36" (91.4 cm): Door Kit No. 4396315

39" (99.1 cm): Door Kit No. 4396316

48" (121.9 cm): Door Kit No.4396317

VinylGrill Coversareavailable from

your dealer.

Built-in models:

27" (68.6 cm): Cover No.4396323

36" (91.4 cm): Cover No.4396325

39" (99.1 cm): Cover No.4396327

Portable models:

27" (68.6 cm): Cover No.4396324

36" (91.4 cm): Cover No.4396326

39" (99.1 cm): Cover No.4396328

48" (121.9 cm) [36" (91.4 cm) grill

with side burner]: Cover No. 4396634

Warranty

KitchenAid ®Gas Grill Products Warranty

LENGTH OF WARRANTY KitchenAid WILL PAY FOR:

FULL ONE-YEAR WARRANTY Factory Specified Parts and Repair Labor to correct defects in materials OR work-

From Date of Purchase manship. Service must be provided by a Service Company designated by KitchenAid.

Limited Five-Year Warranty

Second through Fifth Year from

Date of Purchase

Parts only

Limited Lifetime Warranty

on all Stainless Steel components

including stainless steel grill

burners

For five years from the date of purchase, when this gas grill is used in accordance

with instructions attached or furnished with product, KitchenAid will pay for Factory

Specified Parts to correct defects in materials or workmanship.

KitchenAid also warrants that the structural integrity of the gas grill is free from

defects in materials or workmanship, under normal recommended use for a period of

five years from the date of purchase.

KitchenAid warrants that the stainless steel body housings will be free from defects

in material and workmanship when subjected to normal domestic use and service

for the lifetime of the appliance. This warranty excludes damage to the finish,

such as scratches or discoloration, which may occur during regular use.

The stainless steel grill burners are warranted to be free from defects in material,

workmanship and structural integrity when subject to normal domestic use and

service for the lifetime of the appliance.

The above warranty is limited to the replacement costs of the above component parts.

KitchenAid WILL NOT PAY FOR:

A. Installation of your gas grill or damage caused by improper installation or failure to comply with local code requirements.

B. Shipping, pickup and delivery, removal or re-installation, as your gas grill is designed to be repaired in the home.

C. Service calls to:

1. Correct the installation of your KitchenAid gas grill.

2. Instruct you how to use your KitchenAid gas grill.

3. Replace house fuses or correct house wiring.

4. Perform normal maintenance, including periodic replacement of seals, fittings, etc.

D. Conversion kit or service call for the conversion of your gas grill from natural gas to L.E/propane or from L.R/propane to

natural gas.

E. Repairs when your gas grill is used in other than normal, single-family household use.

E Damage to your gas grill caused by negligence, accident, misuse, fire, flood, acts of God, or use of products,

including cleaning products, not approved by KitchenAid or KitchenAid Canada.

G. Repairs to parts or system resulting from unauthorized modifications to your gas grill.

H. In Canada, travel or transportation expenses for customers who reside in remote areas.

I. Replacement parts or repair labor costs for units operated outside the United States and Canada.

J. Any labor costs during limited warranty period

K. Deterioration due to normal wear and tear of your gas grill.

Notice Regarding All KitchenAid gas grill installations. Access must be provided to the grill's gas source. Install and

operate each gas grill according to instructions provided with product.

KitchenAid and KitchenAid Canada Shall Not be Liable for Incidental or Consequential Damages. Any implied

warranty or merchantability or fitness for a particular purpose is limited in duration to the duration of this warranty.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an

implied warranty lasts, so these exclusions or limitations may not apply to you. This warranty gives you specific legal rights,

and you may also have other rights, which vary, from state to state or province to province.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized KitchenAid dealer to

determine if another warranty applies.

If you need customer or technical assistance, first see the "Grill Use" section of the book. Additional help can be found by

calling the KitchenAid Customer Interaction Center at 1-800422-1230, from anywhere in the U.S.A., and 1-800-807-6777,

from anywhere in Canada.

La page charge ...

KitchenAid KBGN292LSS0 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KBGN292LSS0

Catégorie: Barbecues

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KBGN292LSS0 Owner's manual

KitchenAid KBGN292LSS0 Le manuel du propriétaire

Ce manuel convient également à

KitchenAid KBGN292LSS0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents