Aruba AP-303H Guide d'installation

AP-303H
Aruba
Marque
Aruba
Modèle
AP-303H
Catégorie
Points d'accès WLAN
Taper
Guide d'installation

Ce manuel convient également à

Aruba 303H Series Hospitality Access Points
Installation Guide
AP-303H-IG-01 | September 2017 1
The Aruba 303H Series access point is a high-performance dual-radio wireless device for hospitality and branch
deployments.
This access point use Multiple-Input, Multiple-Output (MIMO) technology to provide secure wireless connectivity
for both 2.4GHz 802.11 b/g/n and 5GHz 802.11 a/n/ac WiFi.
Alternatively, the wired Ethernet ports located on the bottom of the device allow users to connect to the device
directly when linked by an Ethernet cable.
The 303H Series access point can be attached to a standard single-gang wall box using the mount provided, or
converted into a desk-mounted remote access point for branch office deployments using the AP-303H-MNTD
mount kit (sold separately).
The 303H Series access point provides the following capabilities:
IEEE 802.11a/b/g/n/ac operation as a wireless access point
IEEE 802.11a/b/g/n/ac operation as a wireless air monitor
Compatibility with IEEE 802.3af/at PoE
Central management configuration
Supports PoE-in (E0 port)/PoE-out (E3 port)
Support for selected USB peripherals
Integrated Bluetooth Low Energy (BLE) radio
Package Contents
303H Series Access Point
Single gang wall-box mounting bracket
(2x) #6-32 slotted screws
T8H Torx security screw
Hardware Overview
The following sections outline the hardware components of the 303H Series access point.
Figure 1 303H Series (front view)
Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including
the original packing materials. Use these materials to repack and return the unit to the supplier if needed.
PoE-PSE Status
Radio Status
System Status
2 Aruba 303H Series Hospitality Access Points | Installation Guide
LED
The LED displays located on the front and bottom of the access point indicate the following functions:
System Status
The System Status LED indicates the operating condition of the access point. See Table 1.
Table 1 System Status LED
1 blinking: 1s on/1s off
2 flashing: on/off repeated in less than 1s
Radio Status
The Radio Status LED indicates the operating mode of the access point’s radios. See Table 2.
Table 2 Radio Status LED
Color/State Meaning
Off Device is powered off
Green/solid Device is ready; fully functional
Green/blinking
1
Device is booting; not ready
Green/flashing
2
Device is ready; uplink negotiated at suboptimal speed (<1Gbps)
Amber/solid Device is ready; operating in power-save mode (PoE source: 802.3af)
Amber/flashing Device is ready; operating in power-save mode, with uplink negotiated at
suboptimal speed (<1Gbps)
Red/solid Error condition
Color/State Meaning
Off Meets one of the following conditions:
both radios are disabled
device is powered off
Green/solid Both radios enabled in access mode
Green/blinking1 One radio enabled in access mode; one radio
disabled
Amber/solid Both radios enabled in monitor mode
Amber/blinking One radio enabled in monitor mode, other disabled
Alternating
3
One radio in access mode, other radio in monitor mode
Aruba 303H Series Hospitality Access Points | Installation Guide 3
Network Status (E1-E3)
The Network Status LED, located on the sides of the E1-E3 ports, indicates activity transmitted to/from the wired
ports. See Table 3.
Table 3 Network Status LED
PoE-PSE Status (E3)
The PoE-PSE LED located above the E3 port and indicates when the access point is operating as Power Sourcing
Equipment (PSE), providing Power over Ethernet (PoE) to an external device that is physically connected to the
E3 port by Ethernet cable. See Table 4.
Table 4 PoE-PSE Status LED
LED Display Settings
The LEDs have three operating modes that can be selected in the system
management software:
Default mode: Refer to Table 1-Table 4
Off mode: LEDs are off
Blink mode: LEDs blink green
Color/State Meaning
Off Meets one of the following conditions:
device is powered off
port is disabled
no link/activity
Green/solid Link established at max speed (1Gbps)
Green/blinking Activity detected across a max speed link
Amber/solid Link established at reduced speed (10/100Mbps)
Amber/blinking Activity detected across a reduced speed link
Color/State Meaning
Off Access point not supplying PoE, or powered off
Green/solid Access point supplying power to a connected device
Green/blinking Negotiating PoE power supplied to a connected device
4 Aruba 303H Series Hospitality Access Points | Installation Guide
Figure 2 303H Series (rear view)
Console Port
The 5-pin Micro-B connector located on the back of this device. Use an AP-CBL-SERU cable for direct
management of this device when connected to a laptop or serial console. For pin-out details, refer to Figure 3.
Figure 3 Console Port Pin-out
Ethernet Ports
The 303H Series access point is equipped with four active Ethernet ports (E0/PT-E3), shown in Figure 2 (E0) and
Figure 4 (E1-E3). In addition, the AP-303H has a pair of passive pass-through ports (PT and E0/PT), which provide
an electrical connection between the back and the front/bottom of the access point.
Figure 4 303H Series (bottom)
The E0/PT port, located at the back of the access point is 10/100/1000Base-T, auto-sensing, MDI/MDX
wired-network uplink connectivity RJ45 port. It supports IEEE 802.3af/802.3at PoE as a standard Powered Device
(PD) from Power Sourcing Equipment (PSE), such as a midspan injector, or a network infrastructure that supports
PoE.
The E1-E3 ports, located at the bottom of the access point are 10/100/1000Base-T auto-sensing, MDI/MDX wired-
network downlink connectivity RJ45 ports. These ports are used to provide secure network connectivity to wired
devices when physically linked using an Ethernet cable. Refer to Figure 5 for port pin-out information.
Additionally, the E3 port supports PoE-out functionality, and is capable of supplying up to 15.4W to PSE when the
access point is operating in 802.3at PoE mode, or powered by a DC source.
E0
57V 600mA
PT
Micro B console port
E0 Ethernet port
Pass-Through (PT) port
1: NC
2: RX
3: TX
4: GND
5: GND
E0
E0/PT E3E2E1
Aruba 303H Series Hospitality Access Points | Installation Guide 5
Figure 5 Gigabit Ethernet Port Pin-Out
USB Interface
The 303H Series access point is equipped with a USB-A port that is compatible with cellular modems. When
active, the USB port can supply up to 5W/1A to a connected device.
Figure 6 303H Series Side View
Push Button
The push button located on the right side of the device can be used to reset the access point to factory default
settings or turn off/on the LED display.
To reset the access point to factory default settings:
1. Power off the access point.
2. Press and hold the push button using a small, narrow object, such as a paperclip.
3. Power-on the access point without releasing the push button. The System Status LED will flash within 5
seconds.
4. Release the push button.
The system status LED will flash again within 15 seconds indicating that the reset is completed. The access
point will now continue to boot with the factory default settings.
To turn off/on the LED display:
During the normal operation of the access point, press and release the push button using a small, narrow
object, such as a paperclip.
Power
The 303H Series access point supports up to 48V DC when using an AP-AC-48V36C power adapter (sold
separately). The power connector port is located on the side of the device, as shown in Figure 6.
The PoE-in (PoE-PD) allows the E0/PT port to draw power from an 802.3at (preferred) source, or an 802.3af
(optional) source.
When powered by an 802.3at or DC power source, the PoE-out (PoE-PSE) functionality is enabled on port E3,
supplying a maximum output of 15.4W to the wired device.
Refer to Table 4 for power output details. PoE-PSE and USB-A settings can be enabled/disabled through the
software’s WebUI and CLI.
Before You Begin
Refer to the sections below before beginning the installation process.
Pre-Installation Checklist
Before installing the 303H Series access point, be sure that you have the following:
48V
600mA
DC power socket
USB port
Reset button
Security screw lock
6 Aruba 303H Series Hospitality Access Points | Installation Guide
Pre-installed wall box
Cat5E UTP cable with network access installed in the wall box
One of the following power sources:
IEEE 802.3af/at-compliant Power over Ethernet (PoE) source
Aruba AP AC-DC adapter kit (sold separately)
One of the following network services:
Aruba Discovery Protocol (ADP)
DNS server with an “A” record
DHCP Server with vendor-specific options
Identifying Specific Installation Locations
The 303H Series access point must be secured to an Aruba-approved wall or to a desk mount kit. This access
point should be oriented vertically, with Ethernet ports facing downward to facilitate maximum antenna gain.
Use the access point placement map generated by Aruba’s RF Plan software application to determine the proper
installation location(s). Each location should be as close as possible to the center of the intended coverage area
and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/
interference sources will impact RF propagation and should be accounted for during the planning phase and
adjusted for in RF plan.
Identifying Known RF Absorbers/Reflectors/Interference Sources
Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation
phase is critical. Make sure that these sources are taken into consideration when you attach an access point to its
fixed location.
RF absorbers include:
Cement/concrete—Old concrete has high levels of water dissipation, which dries out the concrete, allowing
for potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking
RF signals.
Natural Items—Fish tanks, water fountains, ponds, and trees
Brick
RF reflectors include:
Metal Objects—Metal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows,
blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets.
Do not place an access point between two air conditioning/heating ducts. Make sure that access points are
placed below ducts to avoid RF disturbances.
RF interference sources include:
Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones)
Cordless headset such as those used in call centers or lunch rooms
This device in compliance with governmental requirements, and is designed the so that only authorized network
administrators can change the settings. For more information about access point configuration, refer to the
ArubaOS Quick Start Guide and ArubaOS User Guide.
!
Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in
improper operation. If such use is necessary, this equipment and the other equipment should be observed to
verify that they are operating normally.
!
Portable RF communications equipment (including peripherals such as antenna cables and external antennas)
should be used no closer than 30 cm (12 inches) to any part of the access point. Otherwise, degradation of the
performance of this equipment could result.
!
RF Radiation Exposure Statement: This equipment complies with RF radiation exposure limits. This equipment
should be installed and operated with a minimum distance of 13.78 inches (35cm) between the radiator and
your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
Aruba 303H Series Hospitality Access Points | Installation Guide 7
Installing the Access Point
The 303H Series is designed to mount into a variety of electrical gang boxes.
Use the steps below to install your 303H Series.
1. Begin by removing the existing data wall plate (if applicable).
2. Remove any existing RJ45 connectors (typically snap-in) or cut/remove the UTP cable.
3. Use a short Ethernet cable (sold separately) to connect the E0 port to an RJ45 connector or crimp an RJ45 plug
(not supplied) on the cable and insert in the E0 port. Do the same for the PT port, if used.
4. Align the mounting holes of the 303H Series mounting bracket with mounting holes in you gang box, as
shown in Figure 7 and Figure 8. For worldwide single gang outlet box, the mounting bracket has two sets of
mounting holes to meet the individual installation position requirement.
The applicable standards for the wall boxes are:
IEC 60670-1, GB17466, BS4662 and DIN49073 for Worldwide
ANSI/NEMA OS 1 and OS 2 for US
!
Déclaration sur les limites d'exposition aux radiofréquences : cet équipement est conforme aux limites
d'exposition aux rayonnements radioélectriques spécifiées. Il doit être installé et utilisé à une distance minimale
de 35 cm par rapport à votre corps pour les fréquences de 2,4 et 5 GHz. Cet émetteur-récepteur ne doit pas être
utilisé ou situé à proximité d'autres antennes ou émetteurs-récepteurs.
!
All Aruba access points should be professionally installed by an Aruba-Certified Mobility Professional (ACMP).
The installer is responsible for ensuring that grounding is available and meets applicable national and electrical
codes. Failure to properly install this product may result in physical injury and/or damage to property.
Tous les points d'accès Aruba doivent impérativement être installés par un professionnel agréé. Ce dernier doit
s'assurer que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques
nationaux en vigueur. Le fait de ne pas installer correctement ce produit peut entraîner des blessures
corporelles et / ou des dommages matériels.
!
Use of accessories, transducers and cables other than those specified or provided by the manufacturer of this
equipment could result in increased electromagnetic emissions or decreased electromagnetic immunity of this
equipment and result in improper operation.
8 Aruba 303H Series Hospitality Access Points | Installation Guide
Figure 7 Bracket to Gang Box (US Single Gang Outlet Box Shown)
Figure 8 Bracket to Gang Box (Worldwide Single Gang Outlet Box Shown)
5. Insert the two included machine screws and tighten them to secure the mounting bracket.
6. Connect any required cables to the back of the 303H Series.
7. Align the mounting slots on the back of the 303H Series with the corresponding mounting posts on the wall
mount as shown in Figure 9.
8. Push the access point against the posts and downward until the posts engage the slots at the top of the slots.
Aruba 303H Series Hospitality Access Points | Installation Guide 9
Figure 9 Attaching 303H Series to Bracket
9. Once the access point is fastened onto the wall mount, insert the T8H Torx security screw into the hole
located on the right side of the wall mount and tighten.
10. (Optional) Connect the AC-DC power adapter (sold separately) to the DC power socket located on the right
side of the 303H Series.
Verifying Post-Installation Connectivity
The integrated LED on the access point can be used to verify that the access point access point is receiving power
and initializing successfully (see Table 1). Refer to the ArubaOS Quick Start Guide for further details on verifying
post-installation network connectivity.
Electrical and Environmental Specifications
For additional specifications on this product, please refer to the product data sheet at
www.arubanetworks.com/safety_addendum.
Electrical
Ethernet:
10/100/1000 Base-T auto-sensing Ethernet RJ45 interface
IEEE 802.3u (10 Base-T). IEEE 802.3ab (1000Base-T)
Power over Ethernet IEEE 802.3at 48VDC (nominal)
Power:
48VDC power interference, when powered by an AP-AC-48V36C power cable
Maximum power consumption with a full PoE-PSE and USB load: 31W
Environmental
Operating:
Temperature: 0°C to +40°C (+32°F to +104°F)
Humidity: 5% to 93% non-condensing
Storage and transport:
If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed,
without an output rated 48VDC, minimum 1.2A, marked “LPS” and “Class 2”, and suitable for plugging into a
standard power receptacle in the US and Canada.
10 Aruba 303H Series Hospitality Access Points | Installation Guide
Temperature: -40°C to +70°C (-40°F to +158°F)
Humidity: 5% to 93% non-condensing
Regulatory Information
The regulatory model name (RMN) for 303H Series access point is:
AP-303H/IAP-303H/AP-11D
Aruba provides a multi-language document that contains country-specific restrictions and additional safety and
regulatory information for all Aruba access points. This document can be viewed or downloaded at
www.arubanetworks.com.
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit that is different from that to which the receiver is
connected.
Consult the dealer or an experienced radio or television technician for help.
Federal Communication Commission
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
!
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
the user’s authority to operate this equipment.
Toute modification effectuée sur cet équipement sans l'autorisation expresse de la partie responsable de la
conformité est susceptible d'annuler son droit d'utilisation.
!
Improper termination of access points installed in the United States configured to a non-US model controller is a
violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a
requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).
The network administrator(s) is/are responsible for ensuring that this device operates in accordance with local/
regional laws of the host domain.
11 Aruba 303H Series Hospitality Access Points | Installation Guide
Connect the equipment into an outlet on a circuit that is different from that to which the receiver is
connected.
Consult the dealer or an experienced radio or television technician for help.
European Union Regulatory Conformity
The Declaration of Conformity made under RED 2014/53/EU is available for viewing at:
http://support.arubanetworks.com, then navigate to the Declarations of Conformity > Access Point folder,
select the document that corresponds to your device’s model number as it is indicated on the product label.
Wireless Channel Restrictions
5150-5250MHz band is limited to indoor only in the following countries; Austria (AT), Belgium (BE), Bulgaria (BG), Croatia (HR),
Cyprus (CY), Czech Republic (CZ), Denmark (DK), Estonia (EE), Finland (FI), France (FR), Germany (DE), Greece (GR), Hungary (HU),
Iceland (IS), Ireland (IE), Italy (IT), Latvia (LV), Liechtenstein (LI), Lithuania (LT), Luxembourg (LU), Malta (MT), Netherlands (NL),
Norway (NO), Poland (PL), Portugal (PT), Romania (RO), Slovakia (SK), Slovenia (SL), Spain (ES), Sweden (SE), Switzerland (CH),
Turkey (TR), United Kingdom (UK).
Industry Canada
This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment
Regulations.
In accordance with Industry Canada regulations, this radio transmitter and receiver may only be used with an
antenna, the maximum type and gain of which must be approved by Industry Canada. To reduce potential radio
interference, the type of antenna and its gain shall be chosen so that the equivalent isotropic radiated power
(EIRP) does not exceed the values necessary for effective communication.
This device complies with Industry Canada's license-exempt RSS regulations. Operation of this device is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation.
When operated in 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the
potential for harmful interference with co-channel Mobile Satellite Systems.
Déclaration d’Industrie Canada
Conformément aux réglementations d’Industrie Canada, cet émetteur-récepteur radio doit être utilisé
uniquement avec une antenne dont le type et le gain maximal doivent être approuvés par Industrie Canada.
Pour réduire les interférences radio potentielles, le type d’antenne et son gain doivent être choisis de façon à ce
que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas les valeurs nécessaires à une
communication efficace.
Ce périphérique est conforme aux règlements RSS exempts de licence d’Industrie Canada. L’utilisation de ce
!
Improper termination of access points installed in the United States configured to a non-US model controller is a
violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a
requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).
The network administrator(s) is/are responsible for ensuring that this device operates in accordance with local/
regional laws of the host domain.
Frequency Range MHz Max EIRP
2402-2480 9 dbm
2412-2472 20 dbm
5150-5250 23 dbm
5250-5350 23 dbm
5470-5725 30 dbm
5725-5850 N/A for EU
!
Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/
Instant User Guide for details on restrictions.
12 Aruba 303H Series Hospitality Access Points | Installation Guide
périphérique est soumise aux deux conditions suivantes : (1) ce périphérique ne doit pas provoquer
d’interférences, et (2) ce périphérique doit accepter toute interférence, y compris les interférences susceptibles
de provoquer un dysfonctionnement.
En cas d'utilisation dans la plage de fréquences de 5,15 à 5,25 GHz, cet appareil doit uniquement être utilisé en
intérieur afin de réduire les risques d'interférence avec les systèmes satellites mobiles partageant le même
canal.
Brazil
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência
prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em
caráter primário.
Mexico
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) este dispositivo o dispositivo no
puede causar interferencias perjudiciales, y (2) este dispositivo o dispositivo debe aceptar cualquier
interferencia, incluidas las que puedan causar un funcionamiento no deseado. . Este equipo ha sido diseñado
para operar con antenas internas con una ganancia máxima de antena de 6.2 dBi. La impedancia requerida de la
antena es de 50 ohmios.
Morocco
Нормативные требования Евразийского Экономического Союза
Russia
HPE Russia: ООО "Хьюлетт Паккард Энтерпрайз" Российская Федерация, 125171, г.
Москва, Ленинградское шоссе, 16А, стр.3, Телефон: +7 499 403 4248 Факс: +7 499 403
4677
'HPE Belarus': ИООО «Хьюлетт-Паккард Бел», Республика Беларусь, 220030, г. Минск,
ул. Интернациональная, 36-1, Телефон/факс: +375 17 392 28 20
'HPE Kazakhstan': TOO «Хьюлетт-Паккард (К)», Республика Казахстан, 050040, г.
Алматы, Бостандыкский район, проспект Аль-Фараби, 77/7, Телефон/факс: + 7 727 355 35 50
Kazakhstan
ЖШС "Хьюлетт Паккард Энтерпрайз" Ресей Федерациясы, 125171, Мәскеу, Ленинград тас жолы, 16A блок
3, Телефон: +7 499 403 4248 Факс: +7 499 403 4677
«HEWLETT-PACKARD Bel» ЖШС, Беларусь Республикасы, 220030, Минск қ., Интернациональная көшесі, 36/
1, Телефон/факс: +375 17 392 28 20
ЖШС «Хьюлетт-Паккард (К)», Қазақстан Республикасы, 050040, Алматы к., Бостандык ауданы, Әл-Фараби
даңғ ылы, 77/7, Телефон/факс: +7 (727) 355 35 50
Aruba 303H Series Hospitality Access Points | Installation Guide 13
Korean
이 기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은 기기로서 가정용 환경에서 사용하는 경우 전파간섭
의 우려가 있습니다 .
=> 사용자 안내문은 “ 업무용방송통신기자재 ’ 에만 해당된다
Taiwan
第十二條　　經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得
擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條　　低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現
象時，應立即停用，並改善至無干擾時方得繼續使用。　　
前項合法通信，指依電信法規定作業之無線電通信。　　
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機
設備之干擾。
1. 應避免影響附近雷達系統之操作。
2. 高增益指向性天線只得應用於固定式點對點系統。
3. 電磁波暴露量 MPE 標準值 1 mW/cm
2
, 送測產品實測值為 : 0.184 mW/cm
Singapore
Medical
1. Equipment not suitable for use in the presence of flammable mixtures.
2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources. The end user is
responsible for the resulting medical system complies with the requirements of IEC 60601-1 3rd edition.
3. Wipe with a dry cloth, no additional maintenance required.
4. No serviceable parts, the unit must be sent back to the manufacturer for repair.
5. No modifications are allowed without Aruba approval.
DB100427
14 Aruba 303H Series Hospitality Access Points | Installation Guide
Hong Kong
Oman
Philippines
Singapore
Contact Aruba
Main Site http://www.arubanetworks.com
Support Site http://support.arubanetworks.com
Airheads Social Forums and Knowledge
Base
http://community.arubanetworks.com/
North America Telephone 1-800-943-4526
1-408-754-1200
International Telephone http://www.arubanetworks.com/support-services/contact-support/
Software Licensing Site http://www.hpe.com/networking/support
End-of-Life Information http://www.arubanetworks.com/support-services/end-of-life/
Security Incident Response Team (SIRT) http://www.arubanetworks.com/support-service/security-bulletins/
Email: sirt@arubanetworks.com
HK0011701651
OMAN - TRA
R/4155/17
D100428
Type-Approval No.
ESD-1714710C
DB100427
Aruba 303H Series Hospitality Access Points | Installation Guide 15
Copyright
© Copyright 2018 Hewlett Packard Enterprise Development LP
Open Source Code
This product includes code licensed under the GNU General PublicLicense, the GNU Lesser General Public License, and/or
certain other open source licenses.
A complete machine-readable copy of the source code corresponding to such code is available upon request. This offer is valid
to anyone in receipt of this information and shall expire three years following the date of the final distribution of this product
version by Hewlett Packard Enterprise Company.
To obtain such source code, send a check or money order in the amount of US
$10.00 to:
Hewlett Packard Enterprise Company
Attn: General Counsel
3000 Hanover Street
Palo Alto, CA 94304
USA
Warranty
This hardware product is protected by an Aruba warranty. For more details visit www.hpe.com/us/en/support.html
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Aruba AP-303H Guide d'installation

AP-303H
Aruba
Marque
Aruba
Modèle
AP-303H
Catégorie
Points d'accès WLAN
Taper
Guide d'installation
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents