Dell W-Series 324/325 Access Points Le manuel du propriétaire

Marque: Dell

Modèle: W-Series 324/325 Access Points

Catégorie: Points d'accès WLAN

Taper: Le manuel du propriétaire

Dell Networking 320 Series Access Points

Installation Guide

The Dell 320 Series access points (W-AP324, W-AP325, W-IAP324, and W-IAP325)

support IEEE 802.11ac standards for high-performance WLAN, and are equipped

with two dual-band radios, which can provide access and monitor the network

simultaneously. Multi-user Multiple-input, Multiple-output (MU-MIMO)

technology allows these access points to deliver high-performance 802.11n 2.4 GHz

and 802.11ac 5 GHz functionality, while also supporting 802.11a/b/g wireless

services.

The W-AP324 and W-AP325 access points work in conjunction with a Dell

controller, while the W-IAP324 and W-IAP325 Instant access points can be

configured using a built-in virtual controller.

The 320 Series access points provide the following capabilities:

 Dual wireless transceiver

 IEEE 802.11a/b/g/n/ac operation as a wireless access point

 IEEE 802.11a/b/g/n/ac operation as a wireless air monitor and spectrum analyzer

 Compatibility with IEEE 802.3at PoE+ and 802.3af PoE

 Centralized management configuration and upgrades

 Integrated Bluetooth Low Energy (BLE) radio

Package Contents

 Dell 320 Series Access Point

 9/16" and 15/16” Ceiling Rail Adapters

 Dell Networking 320 Series Access Points Installation Guide (this document)



Dell Networking 320 Series Access Points Regulatory Compliance and Safety

Information Guide

 Dell Networking W-Series Instant Access Point Professional Installation Guide

Supplement (Instant access points only)

 Dell Networking W-Series Instant Quick Start Guide (Instant access points only)

Software

The W-AP324 and W-AP325 access points require AOS 6.4.4 or higher. For

additional information, refer to the Dell Networking W-Series ArubaOS User Guide

and Dell Networking W-Series ArubaOS Quick Start Guide.

The W-IAP324 and W-IAP325 Instant access points require Instant 4.2.1 or higher.

For additional information, refer to the Dell Networking W-Series Instant User Guide

and Dell Networking W-Series Instant Quick Start Guide.

Hardware Overview

Figure 1

LEDs

The 320 Series access points have two LEDs that indicate the system and radio status

of the device.

External Antenna Connectors

The 324 model access points are equipped with four external antenna connectors

located on the front corners of the access point (see Figure 2).

Figure 2

External Antenna Connectors

USB Interface

The 320 Series access points are equipped with a USB port for connectivity with

cellular modems and other USB client devices. When powered by an 802.3at PoE+

or DC source, the USB port can supply power up to 5W.

Figure 3

Bottom Panel

Console Port

The serial console port allows the user to connect the access point to a serial terminal

or a laptop for direct local management. This port is an RJ-45 connector with the

pin-outs shown in Figure 4. Connect it directly to a terminal or terminal server using

an Ethernet cable.

Figure 4

Serial Port Pin-Out

Ethernet Ports

The 320 Series access points are equipped with two 10/100/1000 Base-T (RJ-45) auto-

sensing, MDI/MDX wired-network connectivity ports, ENET0 and ENET1. These

ports support IEEE 802.3af and 802.3at Power over Ethernet (PoE) compliant

sources, accepting 56V DC (nominal) as a standard defined Powered Device (PD)

from a Power Sourcing Equipment (PSE), such as a PoE midspan injector, or

network infrastructure that supports PoE. The Ethernet ports are on the bottom of

the access points. The ports have RJ-45 female connectors with the pin-outs shown

in Figure 5.

Figure 5

Gigabit Ethernet Port Pin-Out

Kensington Lock Slot

The 320 Series access points are equipped with a Kensington lock slot for additional

security.

Reset Button

The reset button can be used to return the access point to factory default settings. To

reset the access point, refer to the steps below:

1. Power-off the access point.

2. Press and hold the reset button using a small, narrow object, such as a paperclip.

3. Power-on the access point without releasing the reset button. The power LED

will flash within 5 seconds.

4. Release the reset button.

The power LED will flash again within 15 seconds indicating that the reset is

completed. The access point will now continue to boot with the factory default

settings.

Power

The ENET0 and ENET1 ports support PoE-in, allowing either port to draw power

from an 802.3at PoE+ source (recommended) or an 802.3af PoE source. When both

PoE and DC power sources are available, the access point will default to using the

DC power source.

The 320 Series access points have a single 12V/30W DC power jack socket to support

the AP-AC-12V30UN AC-to-DC adapter (sold separately).

Power Modes

The 320 Series access points can operate in two power modes. The modes are not

configurable and determined by the access point based on the amount of power

available.

The 320 Series access points operate without restrictions when powered by a DC or

802.3at PoE+ source.

When powered by an 802.3af PoE source, the following restrictions apply:

 Second Ethernet port disabled

 USB interface disabled

 2.4 GHz in 1x1:1 mode

Before You Begin

Access Point Pre-Installation Checklist

Before installing your 320 Series access point, ensure that you have the following:

 CAT5E or CAT6 UTP cable of required length

 One of the following power sources:

 IEEE 802.3at or 802.3af-compliant Power over Ethernet (PoE) source. The

PoE source can be any power source equipment (PSE) controller or midspan

PSE device

 Dell AP-AC-12V30UN AC-to-DC adapter kit (sold separately)

For W-AP324 and W-AP325 access points only:

 Dell Controller provisioned on the network

 Layer 2/3 network connectivity to the access point

 One of the following network services:

 Aruba Discovery Protocol (ADP)

 DNS server with an “A” record

 DHCP Server with vendor-specific options

CAUTION: Access points are classified as radio transmission devices and are

subject to government regulations of the deploying country. The network

administrators are responsible for ensuring that the configuration and operation of

this equipment is in compliance with their country’s regulations. Specifically,

access points must use channel assignments appropriate to the locale in which the

access points will be used. For a complete list of approved channels in your

country, refer to the

Dell Networking W-Series Downloadable Regulatory Table

(DRT) Release Notes

at download.dell-pcw.com.

ATTENTION: Les points d'accès sont considérés comme appareils de

transmission radio et sont soumis aux réglementations gouvernementales du

pays dans lequel ils sont déployés. Le ou les administrateurs réseau doivent

s'assurer que la configuration et le fonctionnement de cet équipement sont

conformes aux normes de leurs pays. De façon plus précise, les points d'accès

doivent employer des canaux adaptés à leur emplacement physique. Pour obtenir

une liste complète des canaux approuvés dans votre pays, reportez-vous aux

notes de version Dell Networking W-Series Downloadable Regulatory Table

(DRT)

à l'adresse download.dell-pcw.com.

NOTE: Inform your supplier if there are any incorrect, missing, or damaged parts. If

possible, retain the carton, including the original packing materials. Use these

materials to repack and return the unit to the supplier if needed.

System Status

Radio Status

LED Color/State Meaning

System Status

(Left)

Off Device powered off

Green/Amber-

Alternating

Device booting; not ready

Green- Solid Device ready

Amber- Solid Device ready; power-save mode (802.3af PoE):

 Single radio

 USB disabled

Green or Amber-

Flashing

Restricted mode:

 Uplink negotiated in sub optimal speed; or

 Radio in non-high throughput mode

Red System error condition

Radio Status

(Right)

Off Device powered off, or both radios disabled

Green- Solid Both radios enabled in access mode

Amber- Solid Both radios enabled in monitor mode

Green/Amber-

Alternating

One radio enabled in access mode, one enabled in

monitor mode

CAUTION: Devices with external antennas must use manufacturer-approved

antennas only. The administrators are responsible for ensuring that the Equivalent

Isotropically Radiated Power (EIRP) levels for external antenna devices are

compliant with the regulatory standards of the host country/domain. Installers are

required to record the antenna gain (dBi) for this device in the system management

software.

ATTENTION: Les appareils munis d'antennes externes doivent utiliser uniquement

des antennes certifiées par le fabricant. Le ou les administrateurs doivent s'assurer

que les niveaux de puissance isotrope rayonnée équivalente (PIRE) de tous les

appareils munis d'antennes externes sont conformes aux normes réglementaires

du pays/domaine hôte. Le ou les installateurs doivent enregistrer le gain d'antenne

(dBi) de cet appareil dans le logiciel de gestion du système.

NOTE: The USB port is disabled when the access point is powered by an 802.3af

PoE source.

ANT1

ANT0

ANT2

ANT3

12V 2.5A

. . .

USB Port

Ethernet Ports

Console Port

DC Power Socket

Reset Button

Kensington Lock

BLE Radio

1000Base-T Gigabit

Ethernet Port

RJ-45 Female

Pin-Out

Signal Name

BI_DC+

BI_DC-

BI_DD+

BI_DD-

BI_DA+

BI_DA-

BI_DB+

BI_DB-

Function

Bi-directional pair +C

Bi-directional pair -C

Bi-directional pair +D

Bi-directional pair -D

Bi-directional pair +A

Bi-directional pair -A

Bi-directional pair +B

Bi-directional pair -B

CAUTION: FCC Statement: Improper termination of access points installed in the

United States configured to non-US model controllers will be in violation of the FCC

grant of equipment authorization. Any such willful or intentional violation may result

in a requirement by the FCC for immediate termination of operation and may be

subject to forfeiture (47 CFR 1.80).

ATTENTION: Déclaration FCC l’arrêt incorrect des points d’accès installés aux

États-Unis qui sont configurés sur des contrôleurs autres que le modèle agréé

aux États-Unis est considéré comme contrevenant à l’homologation FCC. Toute

violation délibérée ou intentionnelle de cette condition peut entraîner une

injonction d’arrêt immédiat de son utilisation par la FCC et peut déboucher sur la

confiscation de l’équipement (47 CFR 1.80).

CAUTION: EU Statement:

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer

to the User Guide

for details on restrictions.

Produit réseau local radio basse puissance operant dans la bande fréquence 2.4

GHz et 5 GHz. Merci de vous referrer au manuel utilisateur pour les details des

restrictions.

Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere

Informationen bezlüglich Einschränkungen finden Sie im benutzerhandbuch

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento

alla manuale utente per avere informazioni detagliate sulle restrizioni.

NOTE: Dell access points are designed in compliance with governmental

requirements, so that only authorized network administrators are permitted to

change the settings for this device. For more information about access point

configuration, refer to the Quick Start Guide and User Guide for your device.

Dell Networking 320 Series

Access Points

Installation Guide

dell.com

Dell Networking 320 Series Access Points | Installation Guide

Part Number 0511834-02| July 2015

Contacting Dell

Website Support

Main Website dell.com

Contact Information dell.com/contactdell

Support Website dell.com /support

Documentation Website dell.com /support/manuals

Aruba Wireless Networks

, the registered Aruba the Mobile Edge Company logo, and Aruba Mobility

Management System

. Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc.

Originated in the USA. All other trademarks are the property of their respective owners.

Open Source Code

Certain Aruba products include Open Source software code developed by third parties, including software code

subject to the GNU General Public License (GPL), GNU Lesser General Public License (LGPL), or other Open

Source Licenses. The Open Source code used can be found at this site:

http://www.arubanetworks.com/open_source

reserved. This product includes software developed by Lars Fenneberg, et al.

Legal Notice

The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate

other vendors’ VPN client devices constitutes complete acceptance of liability by that individual or corporation for

this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against

it with respect to infringement of copyright on behalf of those vendors.

Verifying Pre-Installation Connectivity

Before installing access points in a network environment, make sure that they are able

to locate and connect to the controller after power on.

Specifically, you must verify the following conditions:

 When connected to the network, each access point is assigned a valid IP address

 Access points are able to locate the controller

Refer to the Quick Start Guide for instructions on locating and connecting to the

controller.

Pre-Installation Network Requirements

After WLAN planning is complete and the appropriate products and their placement

have been determined, the Dell controller(s) must be installed and initial setup

completed before the Dell access points are deployed.

For initial setup of the controller, refer to Quick Start Guide.

Identifying Specific Installation Locations

You can mount the 320 Series access point on a wall or on the ceiling. Use the access

point placement map generated by the Dell VisualRF Plan software application to

determine the proper installation location(s). Each location should be as close as

possible to the center of the intended coverage area and should be free from

obstructions or obvious sources of interference. These RF absorbers/reflectors/

interference sources will impact RF propagation and should be accounted for during

the planning phase and adjusted for in the RF plan.

Identifying Known RF Absorbers/Reflectors/Interference Sources

Identifying known RF absorbers, reflectors, and interference sources while in the field

during the installation phase is critical. Make sure that these sources are taken into

consideration when you attach an access point to its fixed location. Examples of

sources that degrade RF performance include:

 Cement and brick

 Objects that contain water

 Metal

 Microwave ovens

 Wireless phones and headsets

Installing the Access Point

Using the Ceiling Rail Adapter

The 320 Series access points are shipped with two ceiling rail adapters for 9/16” and

15/16” ceiling rails. Additional wall mount adapters and ceiling rail adapters for other

rail styles are available as accessory kits

1. Pull the necessary cables through a prepared hole in the ceiling tile close to where

the access point will be placed.

2. Place the adapter against the back of the access point with the adapter at an angle

of approximately 30 degrees to the tabs (see Figure 6).

3. Twist the adapter clockwise until it snaps in place into the tabs (see Figure 6).

Figure 6

Attaching the Ceiling Rail Adapter

4. If necessary, connect the console cable to the console port on the back of the

access point.

5. Hold the access point next to the ceiling tile rail with the ceiling tile rail mounting

slots at approximately a 30-degree angle to the ceiling tile rail (see Figure 7).

Make sure that any cable slack is above the ceiling tile.

6. Pushing toward the ceiling tile, rotate the access point clockwise until the device

clicks in place on the ceiling tile rail.

Figure 7

Mounting the Access Point

7. On the 324 model access points, install the external antennas according to the

manufacturer’s instructions, and connect the antennas to the antenna interfaces

on the access point.

Connecting Required Cables

Install cables in accordance with all applicable local and national regulations and

practices.

Verifying Post-Installation Connectivity

The integrated LEDs on the access point can be used to verify that the device is

receiving power and initializing successfully (see Table 1). Refer to the Quick Start

Guide for further details on verifying post-installation network connectivity.

Configuring the Access Point

Access Point Provisioning/Reprovisioning

Provisioning parameters are unique to each access point. These local access point

parameters are initially configured on the controller, and then pushed out to the

access points and stored on the access points. Dell recommends that provisioning

settings be configured via the AOS Web UI only. Refer to the User Guide for details.

Access Point Configuration

Configuration parameters are network or controller specific. They are configured and

stored on the controller and then pushed out to the access points. These parameters

remain stored on the controller.

Configuration settings can be configured via the AOS Web UI or CLI. Refer to the

User Guide or Dell Networking W-Series ArubaOS Command-Line Interface Reference

Guide for details.

NOTE: The instructions in this section are applicable to the W-AP324 and W-AP325

access points only.

NOTE: Service to all Dell Networking products should be performed by a qualified

technician.

CAUTION: The installer is responsible for securing the access point onto the ceiling

tile rail in accordance with the steps below. Failure to properly install this product

may result in physical injury and/or damage to property.

ATTENTION: L’installateur est chargé de sécuriser le point d’accès sur le rail de

montage au plafond en suivant la procédure ci-après. Toute installation incorrecte

du produit peut entraîner des blessures physiques et/ou des dommages matériels.

NOTE: The instructions for this section are applicable to the W-AP324 and W-AP325

access points only.

Dell W-Series 324/325 Access Points Le manuel du propriétaire

Marque: Dell

Modèle: W-Series 324/325 Access Points

Catégorie: Points d'accès WLAN

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Dell W-Series 324/325 Access Points Owner's manual

Dell W-Series 324/325 Access Points Le manuel du propriétaire

Dell W-Series 324/325 Access Points Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents