Aruba AP-303H Series Guide d'installation

Marque: Aruba

Modèle: AP-303H Series

Catégorie: Points d'accès WLAN

Taper: Guide d'installation

Ce manuel convient également à

Aruba 303H Series Hospitality Access Points

Installation Guide

AP-303H-IG-01 | September 2017 1

The Aruba 303H Series access point is a high-performance dual-radio wireless device for hospitality and branch

deployments.

This access point use Multiple-Input, Multiple-Output (MIMO) technology to provide secure wireless connectivity

for both 2.4GHz 802.11 b/g/n and 5GHz 802.11 a/n/ac WiFi.

Alternatively, the wired Ethernet ports located on the bottom of the device allow users to connect to the device

directly when linked by an Ethernet cable.

The 303H Series access point can be attached to a standard single-gang wall box using the mount provided, or

converted into a desk-mounted remote access point for branch office deployments using the AP-303H-MNTD

mount kit (sold separately).

The 303H Series access point provides the following capabilities:

 IEEE 802.11a/b/g/n/ac operation as a wireless access point

 IEEE 802.11a/b/g/n/ac operation as a wireless air monitor

 Compatibility with IEEE 802.3af/at PoE

 Central management configuration

 Supports PoE-in (E0 port)/PoE-out (E3 port)

 Support for selected USB peripherals

 Integrated Bluetooth Low Energy (BLE) radio

Package Contents

 303H Series Access Point

 Single gang wall-box mounting bracket

 (2x) #6-32 slotted screws

 T8H Torx security screw

Hardware Overview

The following sections outline the hardware components of the 303H Series access point.

Figure 1 303H Series (front view)

Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including

the original packing materials. Use these materials to repack and return the unit to the supplier if needed.

PoE-PSE Status

Radio Status

System Status

2 Aruba 303H Series Hospitality Access Points | Installation Guide

LED

The LED displays located on the front and bottom of the access point indicate the following functions:

System Status

The System Status LED indicates the operating condition of the access point. See Table 1.

Table 1 System Status LED

1 blinking: 1s on/1s off

2 flashing: on/off repeated in less than 1s

Radio Status

The Radio Status LED indicates the operating mode of the access point’s radios. See Table 2.

Table 2 Radio Status LED

Color/State Meaning

Off Device is powered off

Green/solid Device is ready; fully functional

Green/blinking

Device is booting; not ready

Green/flashing

Device is ready; uplink negotiated at suboptimal speed (<1Gbps)

Amber/solid Device is ready; operating in power-save mode (PoE source: 802.3af)

Amber/flashing Device is ready; operating in power-save mode, with uplink negotiated at

suboptimal speed (<1Gbps)

Red/solid Error condition

Color/State Meaning

Off Meets one of the following conditions:

 both radios are disabled

 device is powered off

Green/solid Both radios enabled in access mode

Green/blinking1 One radio enabled in access mode; one radio

disabled

Amber/solid Both radios enabled in monitor mode

Amber/blinking One radio enabled in monitor mode, other disabled

Alternating

One radio in access mode, other radio in monitor mode

Aruba 303H Series Hospitality Access Points | Installation Guide 3

Network Status (E1-E3)

The Network Status LED, located on the sides of the E1-E3 ports, indicates activity transmitted to/from the wired

ports. See Table 3.

Table 3 Network Status LED

PoE-PSE Status (E3)

The PoE-PSE LED located above the E3 port and indicates when the access point is operating as Power Sourcing

Equipment (PSE), providing Power over Ethernet (PoE) to an external device that is physically connected to the

E3 port by Ethernet cable. See Table 4.

Table 4 PoE-PSE Status LED

LED Display Settings

The LEDs have three operating modes that can be selected in the system

management software:

 Default mode: Refer to Table 1-Table 4

 Off mode: LEDs are off

 Blink mode: LEDs blink green

Color/State Meaning

Off Meets one of the following conditions:

 device is powered off

 port is disabled

 no link/activity

Green/solid Link established at max speed (1Gbps)

Green/blinking Activity detected across a max speed link

Amber/solid Link established at reduced speed (10/100Mbps)

Amber/blinking Activity detected across a reduced speed link

Color/State Meaning

Off Access point not supplying PoE, or powered off

Green/solid Access point supplying power to a connected device

Green/blinking Negotiating PoE power supplied to a connected device

4 Aruba 303H Series Hospitality Access Points | Installation Guide

Figure 2 303H Series (rear view)

Console Port

The 5-pin Micro-B connector located on the back of this device. Use an AP-CBL-SERU cable for direct

management of this device when connected to a laptop or serial console. For pin-out details, refer to Figure 3.

Figure 3 Console Port Pin-out

Ethernet Ports

The 303H Series access point is equipped with four active Ethernet ports (E0/PT-E3), shown in Figure 2 (E0) and

Figure 4 (E1-E3). In addition, the AP-303H has a pair of passive pass-through ports (PT and E0/PT), which provide

an electrical connection between the back and the front/bottom of the access point.

Figure 4 303H Series (bottom)

The E0/PT port, located at the back of the access point is 10/100/1000Base-T, auto-sensing, MDI/MDX

wired-network uplink connectivity RJ45 port. It supports IEEE 802.3af/802.3at PoE as a standard Powered Device

(PD) from Power Sourcing Equipment (PSE), such as a midspan injector, or a network infrastructure that supports

PoE.

The E1-E3 ports, located at the bottom of the access point are 10/100/1000Base-T auto-sensing, MDI/MDX wired-

network downlink connectivity RJ45 ports. These ports are used to provide secure network connectivity to wired

devices when physically linked using an Ethernet cable. Refer to Figure 5 for port pin-out information.

Additionally, the E3 port supports PoE-out functionality, and is capable of supplying up to 15.4W to PSE when the

access point is operating in 802.3at PoE mode, or powered by a DC source.

57V 600mA

Micro B console port

E0 Ethernet port

Pass-Through (PT) port

1: NC

2: RX

3: TX

4: GND

5: GND

E0/PT E3E2E1

Aruba 303H Series Hospitality Access Points | Installation Guide 5

Figure 5 Gigabit Ethernet Port Pin-Out

USB Interface

The 303H Series access point is equipped with a USB-A port that is compatible with cellular modems. When

active, the USB port can supply up to 5W/1A to a connected device.

Figure 6 303H Series Side View

Push Button

The push button located on the right side of the device can be used to reset the access point to factory default

settings or turn off/on the LED display.

 To reset the access point to factory default settings:

1. Power off the access point.

2. Press and hold the push button using a small, narrow object, such as a paperclip.

3. Power-on the access point without releasing the push button. The System Status LED will flash within 5

seconds.

4. Release the push button.

The system status LED will flash again within 15 seconds indicating that the reset is completed. The access

point will now continue to boot with the factory default settings.

 To turn off/on the LED display:

During the normal operation of the access point, press and release the push button using a small, narrow

object, such as a paperclip.

Power

The 303H Series access point supports up to 48V DC when using an AP-AC-48V36C power adapter (sold

separately). The power connector port is located on the side of the device, as shown in Figure 6.

The PoE-in (PoE-PD) allows the E0/PT port to draw power from an 802.3at (preferred) source, or an 802.3af

(optional) source.

When powered by an 802.3at or DC power source, the PoE-out (PoE-PSE) functionality is enabled on port E3,

supplying a maximum output of 15.4W to the wired device.

Refer to Table 4 for power output details. PoE-PSE and USB-A settings can be enabled/disabled through the

software’s WebUI and CLI.

Before You Begin

Refer to the sections below before beginning the installation process.

Pre-Installation Checklist

Before installing the 303H Series access point, be sure that you have the following:

48V

600mA

DC power socket

USB port

Reset button

Security screw lock

6 Aruba 303H Series Hospitality Access Points | Installation Guide

 Pre-installed wall box

 Cat5E UTP cable with network access installed in the wall box

 One of the following power sources:

 IEEE 802.3af/at-compliant Power over Ethernet (PoE) source

 Aruba AP AC-DC adapter kit (sold separately)

One of the following network services:

 Aruba Discovery Protocol (ADP)

 DNS server with an “A” record

 DHCP Server with vendor-specific options

Identifying Specific Installation Locations

The 303H Series access point must be secured to an Aruba-approved wall or to a desk mount kit. This access

point should be oriented vertically, with Ethernet ports facing downward to facilitate maximum antenna gain.

Use the access point placement map generated by Aruba’s RF Plan software application to determine the proper

installation location(s). Each location should be as close as possible to the center of the intended coverage area

and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/

interference sources will impact RF propagation and should be accounted for during the planning phase and

adjusted for in RF plan.

Identifying Known RF Absorbers/Reflectors/Interference Sources

Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation

phase is critical. Make sure that these sources are taken into consideration when you attach an access point to its

fixed location.

RF absorbers include:

 Cement/concrete—Old concrete has high levels of water dissipation, which dries out the concrete, allowing

for potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking

RF signals.

 Natural Items—Fish tanks, water fountains, ponds, and trees

 Brick

RF reflectors include:

 Metal Objects—Metal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows,

blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets.

 Do not place an access point between two air conditioning/heating ducts. Make sure that access points are

placed below ducts to avoid RF disturbances.

RF interference sources include:

 Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones)

Cordless headset such as those used in call centers or lunch rooms

This device in compliance with governmental requirements, and is designed the so that only authorized network

administrators can change the settings. For more information about access point configuration, refer to the

ArubaOS Quick Start Guide and ArubaOS User Guide.

Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in

improper operation. If such use is necessary, this equipment and the other equipment should be observed to

verify that they are operating normally.

Portable RF communications equipment (including peripherals such as antenna cables and external antennas)

should be used no closer than 30 cm (12 inches) to any part of the access point. Otherwise, degradation of the

performance of this equipment could result.

RF Radiation Exposure Statement: This equipment complies with RF radiation exposure limits. This equipment

should be installed and operated with a minimum distance of 13.78 inches (35cm) between the radiator and

your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction

with any other antenna or transmitter.

Aruba 303H Series Hospitality Access Points | Installation Guide 7

Installing the Access Point

The 303H Series is designed to mount into a variety of electrical gang boxes.

Use the steps below to install your 303H Series.

1. Begin by removing the existing data wall plate (if applicable).

2. Remove any existing RJ45 connectors (typically snap-in) or cut/remove the UTP cable.

3. Use a short Ethernet cable (sold separately) to connect the E0 port to an RJ45 connector or crimp an RJ45 plug

(not supplied) on the cable and insert in the E0 port. Do the same for the PT port, if used.

4. Align the mounting holes of the 303H Series mounting bracket with mounting holes in you gang box, as

shown in Figure 7 and Figure 8. For worldwide single gang outlet box, the mounting bracket has two sets of

mounting holes to meet the individual installation position requirement.

The applicable standards for the wall boxes are:

 IEC 60670-1, GB17466, BS4662 and DIN49073 for Worldwide

 ANSI/NEMA OS 1 and OS 2 for US

Déclaration sur les limites d'exposition aux radiofréquences : cet équipement est conforme aux limites

d'exposition aux rayonnements radioélectriques spécifiées. Il doit être installé et utilisé à une distance minimale

de 35 cm par rapport à votre corps pour les fréquences de 2,4 et 5 GHz. Cet émetteur-récepteur ne doit pas être

utilisé ou situé à proximité d'autres antennes ou émetteurs-récepteurs.

All Aruba access points should be professionally installed by an Aruba-Certified Mobility Professional (ACMP).

The installer is responsible for ensuring that grounding is available and meets applicable national and electrical

codes. Failure to properly install this product may result in physical injury and/or damage to property.

Tous les points d'accès Aruba doivent impérativement être installés par un professionnel agréé. Ce dernier doit

s'assurer que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques

nationaux en vigueur. Le fait de ne pas installer correctement ce produit peut entraîner des blessures

corporelles et / ou des dommages matériels.

Use of accessories, transducers and cables other than those specified or provided by the manufacturer of this

equipment could result in increased electromagnetic emissions or decreased electromagnetic immunity of this

equipment and result in improper operation.

8 Aruba 303H Series Hospitality Access Points | Installation Guide

Figure 7 Bracket to Gang Box (US Single Gang Outlet Box Shown)

Figure 8 Bracket to Gang Box (Worldwide Single Gang Outlet Box Shown)

5. Insert the two included machine screws and tighten them to secure the mounting bracket.

6. Connect any required cables to the back of the 303H Series.

7. Align the mounting slots on the back of the 303H Series with the corresponding mounting posts on the wall

mount as shown in Figure 9.

8. Push the access point against the posts and downward until the posts engage the slots at the top of the slots.

Aruba 303H Series Hospitality Access Points | Installation Guide 9

Figure 9 Attaching 303H Series to Bracket

9. Once the access point is fastened onto the wall mount, insert the T8H Torx security screw into the hole

located on the right side of the wall mount and tighten.

10. (Optional) Connect the AC-DC power adapter (sold separately) to the DC power socket located on the right

side of the 303H Series.

Verifying Post-Installation Connectivity

The integrated LED on the access point can be used to verify that the access point access point is receiving power

and initializing successfully (see Table 1). Refer to the ArubaOS Quick Start Guide for further details on verifying

post-installation network connectivity.

Electrical and Environmental Specifications

For additional specifications on this product, please refer to the product data sheet at

www.arubanetworks.com/safety_addendum.

Electrical

 Ethernet:

 10/100/1000 Base-T auto-sensing Ethernet RJ45 interface

 IEEE 802.3u (10 Base-T). IEEE 802.3ab (1000Base-T)

 Power over Ethernet IEEE 802.3at 48VDC (nominal)

 Power:

 48VDC power interference, when powered by an AP-AC-48V36C power cable

 Maximum power consumption with a full PoE-PSE and USB load: 31W

Environmental

 Operating:

 Temperature: 0°C to +40°C (+32°F to +104°F)

 Humidity: 5% to 93% non-condensing

 Storage and transport:

If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed,

without an output rated 48VDC, minimum 1.2A, marked “LPS” and “Class 2”, and suitable for plugging into a

standard power receptacle in the US and Canada.

10 Aruba 303H Series Hospitality Access Points | Installation Guide

 Temperature: -40°C to +70°C (-40°F to +158°F)

 Humidity: 5% to 93% non-condensing

Regulatory Information

The regulatory model name (RMN) for 303H Series access point is:

 AP-303H/IAP-303H/AP-11D

Aruba provides a multi-language document that contains country-specific restrictions and additional safety and

regulatory information for all Aruba access points. This document can be viewed or downloaded at

www.arubanetworks.com.

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit that is different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio or television technician for help.

Federal Communication Commission

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void

the user’s authority to operate this equipment.

Toute modification effectuée sur cet équipement sans l'autorisation expresse de la partie responsable de la

conformité est susceptible d'annuler son droit d'utilisation.

Improper termination of access points installed in the United States configured to a non-US model controller is a

violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a

requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).

The network administrator(s) is/are responsible for ensuring that this device operates in accordance with local/

regional laws of the host domain.

11 Aruba 303H Series Hospitality Access Points | Installation Guide

 Connect the equipment into an outlet on a circuit that is different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio or television technician for help.

European Union Regulatory Conformity

The Declaration of Conformity made under RED 2014/53/EU is available for viewing at:

http://support.arubanetworks.com, then navigate to the Declarations of Conformity > Access Point folder,

select the document that corresponds to your device’s model number as it is indicated on the product label.

Wireless Channel Restrictions

5150-5250MHz band is limited to indoor only in the following countries; Austria (AT), Belgium (BE), Bulgaria (BG), Croatia (HR),

Cyprus (CY), Czech Republic (CZ), Denmark (DK), Estonia (EE), Finland (FI), France (FR), Germany (DE), Greece (GR), Hungary (HU),

Iceland (IS), Ireland (IE), Italy (IT), Latvia (LV), Liechtenstein (LI), Lithuania (LT), Luxembourg (LU), Malta (MT), Netherlands (NL),

Norway (NO), Poland (PL), Portugal (PT), Romania (RO), Slovakia (SK), Slovenia (SL), Spain (ES), Sweden (SE), Switzerland (CH),

Turkey (TR), United Kingdom (UK).

Industry Canada

This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment

Regulations.

In accordance with Industry Canada regulations, this radio transmitter and receiver may only be used with an

antenna, the maximum type and gain of which must be approved by Industry Canada. To reduce potential radio

interference, the type of antenna and its gain shall be chosen so that the equivalent isotropic radiated power

(EIRP) does not exceed the values necessary for effective communication.

This device complies with Industry Canada's license-exempt RSS regulations. Operation of this device is subject

to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation.

When operated in 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the

potential for harmful interference with co-channel Mobile Satellite Systems.

Déclaration d’Industrie Canada

Conformément aux réglementations d’Industrie Canada, cet émetteur-récepteur radio doit être utilisé

uniquement avec une antenne dont le type et le gain maximal doivent être approuvés par Industrie Canada.

Pour réduire les interférences radio potentielles, le type d’antenne et son gain doivent être choisis de façon à ce

que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas les valeurs nécessaires à une

communication efficace.

Ce périphérique est conforme aux règlements RSS exempts de licence d’Industrie Canada. L’utilisation de ce

Improper termination of access points installed in the United States configured to a non-US model controller is a

violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a

requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).

The network administrator(s) is/are responsible for ensuring that this device operates in accordance with local/

regional laws of the host domain.

Frequency Range MHz Max EIRP

2402-2480 9 dbm

2412-2472 20 dbm

5150-5250 23 dbm

5250-5350 23 dbm

5470-5725 30 dbm

5725-5850 N/A for EU

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/

Instant User Guide for details on restrictions.

12 Aruba 303H Series Hospitality Access Points | Installation Guide

périphérique est soumise aux deux conditions suivantes : (1) ce périphérique ne doit pas provoquer

d’interférences, et (2) ce périphérique doit accepter toute interférence, y compris les interférences susceptibles

de provoquer un dysfonctionnement.

En cas d'utilisation dans la plage de fréquences de 5,15 à 5,25 GHz, cet appareil doit uniquement être utilisé en

intérieur afin de réduire les risques d'interférence avec les systèmes satellites mobiles partageant le même

canal.

Brazil

Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência

prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em

caráter primário.

Mexico

La operación de este equipo está sujeta a las siguientes dos condiciones: (1) este dispositivo o dispositivo no

puede causar interferencias perjudiciales, y (2) este dispositivo o dispositivo debe aceptar cualquier

interferencia, incluidas las que puedan causar un funcionamiento no deseado. . Este equipo ha sido diseñado

para operar con antenas internas con una ganancia máxima de antena de 6.2 dBi. La impedancia requerida de la

antena es de 50 ohmios.

Morocco

Нормативные требования Евразийского Экономического Союза

Russia

HPE Russia: ООО "Хьюлетт Паккард Энтерпрайз" Российская Федерация, 125171, г.

Москва, Ленинградское шоссе, 16А, стр.3, Телефон: +7 499 403 4248 Факс: +7 499 403

4677

'HPE Belarus': ИООО «Хьюлетт-Паккард Бел», Республика Беларусь, 220030, г. Минск,

ул. Интернациональная, 36-1, Телефон/факс: +375 17 392 28 20

'HPE Kazakhstan': TOO «Хьюлетт-Паккард (К)», Республика Казахстан, 050040, г.

Алматы, Бостандыкский район, проспект Аль-Фараби, 77/7, Телефон/факс: + 7 727 355 35 50

Kazakhstan

ЖШС "Хьюлетт Паккард Энтерпрайз" Ресей Федерациясы, 125171, Мәскеу, Ленинград тас жолы, 16A блок

3, Телефон: +7 499 403 4248 Факс: +7 499 403 4677

«HEWLETT-PACKARD Bel» ЖШС, Беларусь Республикасы, 220030, Минск қ., Интернациональная көшесі, 36/

1, Телефон/факс: +375 17 392 28 20

ЖШС «Хьюлетт-Паккард (К)», Қазақстан Республикасы, 050040, Алматы к., Бостандык ауданы, Әл-Фараби

даңғ ылы, 77/7, Телефон/факс: +7 (727) 355 35 50

Aruba 303H Series Hospitality Access Points | Installation Guide 13

Korean

이 기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은 기기로서 가정용 환경에서 사용하는 경우 전파간섭

의 우려가 있습니다 .

=> 사용자 안내문은 “ 업무용방송통신기자재 ’ 에만 해당된다

Taiwan

第十二條　　經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得

擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條　　低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現

象時，應立即停用，並改善至無干擾時方得繼續使用。　　

前項合法通信，指依電信法規定作業之無線電通信。　　

低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機

設備之干擾。

1. 應避免影響附近雷達系統之操作。

2. 高增益指向性天線只得應用於固定式點對點系統。

3. 電磁波暴露量 MPE 標準值 1 mW/cm

, 送測產品實測值為 : 0.184 mW/cm

Singapore

Medical

1. Equipment not suitable for use in the presence of flammable mixtures.

2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources. The end user is

responsible for the resulting medical system complies with the requirements of IEC 60601-1 3rd edition.

3. Wipe with a dry cloth, no additional maintenance required.

4. No serviceable parts, the unit must be sent back to the manufacturer for repair.

5. No modifications are allowed without Aruba approval.

DB100427

14 Aruba 303H Series Hospitality Access Points | Installation Guide

Hong Kong

Oman

Philippines

Singapore

Contact Aruba

Main Site http://www.arubanetworks.com

Support Site http://support.arubanetworks.com

Airheads Social Forums and Knowledge

Base

http://community.arubanetworks.com/

North America Telephone 1-800-943-4526

1-408-754-1200

International Telephone http://www.arubanetworks.com/support-services/contact-support/

Software Licensing Site http://www.hpe.com/networking/support

End-of-Life Information http://www.arubanetworks.com/support-services/end-of-life/

Security Incident Response Team (SIRT) http://www.arubanetworks.com/support-service/security-bulletins/

Email: sirt@arubanetworks.com

HK0011701651

OMAN - TRA

R/4155/17

D100428

Type-Approval No.

ESD-1714710C

DB100427

Aruba 303H Series Hospitality Access Points | Installation Guide 15

Open Source Code

This product includes code licensed under the GNU General PublicLicense, the GNU Lesser General Public License, and/or

certain other open source licenses.

A complete machine-readable copy of the source code corresponding to such code is available upon request. This offer is valid

to anyone in receipt of this information and shall expire three years following the date of the final distribution of this product

version by Hewlett Packard Enterprise Company.

To obtain such source code, send a check or money order in the amount of US

$10.00 to:

Hewlett Packard Enterprise Company

Attn: General Counsel

3000 Hanover Street

Palo Alto, CA 94304

USA

Warranty

This hardware product is protected by an Aruba warranty. For more details visit www.hpe.com/us/en/support.html

Aruba AP-303H Series Guide d'installation

Marque: Aruba

Modèle: AP-303H Series

Catégorie: Points d'accès WLAN

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Aruba AP-303H Series Installation guide

Aruba AP-303H Series Guide d'installation

Ce manuel convient également à

Aruba AP-303H Series Guide d'installation

dans d''autres langues

Documents connexes

Autres documents