AEG DD8694-M Manuel utilisateur

Catégorie
Hottes
Taper
Manuel utilisateur
DD8694-M USER MANUAL
MODE D’EMPLOI ET INSTALLATION
BEDIENUNGSANLEITUNG
INSTRUCTIES VOOR HET GEBRUIK EN INSTALLEREN
INSTRUCCIONES PARA EL USO Y LA INSTALACIÒN
INSTRUÇÕES PARA O USO E A INSTALAÇÃO
EN
FR
DE
NL
ES
PT
COOKER HOOD
HOTTE DE CUISINE
DUNSTABZUGSHAUBE
DAMPKAP
CAMPANA
EXAUSTOR
2
14
26
38
50
62
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created
it to give you impeccable performance for many years, with
innovative technologies that help make life simpler fea-
tures you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
ACCESSORIES AND CONSUMABLES
In the AEG webshop, you’ll find everything you need to keep
all your AEG appliances looking spotless and working per-
fectly. Along with a wide range of accessories designed and
built to the high quality standards you would expect, from
specialist cookware to cutlery baskets, from bottle holders to
delicate laundry bags…
Visit the webshop at:
www.aeg-electrolux.com/shop
3
CONTENTS
4
5
7
10
11
Recommendations And Suggestions
Characteristics
Installation
Use
Maintenance
Contents
RECOMMENDATIONS AND SUGGESTIONS
4
RECOMMENDATIONS AND SUGGESTIONS
The Instructions for Use apply to several versions of this appliance. Ac-
cordingly, you may find descriptions of individual features that do not
apply to your specific appliance.
INSTALLATION
• Themanufacturerwillnotbeheldliableforanydamagesresultingfrom
in-correct or improper installation.
• Theminimumsafetydistancebetweenthecookertopandtheextractor
hood is 650 mm (some models can be installed at a lower height, please
re-fer to the paragraphs on working dimensions and installation).
• Checkthatthemainsvoltagecorrespondstothatindicatedontherating
plate fixed to the inside of the hood.
• ForClassIappliances,checkthatthedomesticpowersupplyguarantees
adequate earthing. Connect the extractor to the exhaust flue through a
pipe of minimum diameter 120 mm. The route of the flue must be as short
as possible.
• Donotconnecttheextractorhoodtoexhaustductscarryingcombustion
fumes (boilers, fireplaces, etc.).
• Iftheextractorisusedinconjunctionwithnonelectricalappliances(e.g.
gas burning appliances), a sufficient degree of aeration must be guaran-
teed in the room in order to prevent the backflow of exhaust gas. The
kitchen must have an opening communicating directly with the open air
in order to guarantee the entry of clean air.
USE
• The extractor hood has been designed exclusively for domestic use to
eliminate kitchen smells.
• Never usethehoodforpurposesotherthan for whichithasbeende-
signed.
• Neverleavehighnakedflamesunderthehoodwhenitisinoperation.
• Adjusttheflameintensitytodirectitontothebottomofthepanonly,
making sure that it does not engulf the sides.
• Deepfatfryersmustbecontinuouslymonitoredduringuse:overheatedoil
can burst into flames.
• Donotflambèundertherangehood;riskoffire
• Thisapplianceisnotintendedforusebypersons(includingchildren)with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction con-
cerning use of the appliance by a person responsible for their safety.
• Childrenshouldbesupervisedtoensurethattheydonotplaywiththe
appliance.
MAINTENANCE
• Switchofforunplugtheappliancefromthemainssupplybeforecarrying
out any maintenance work.
• Cleanand/orreplacetheFiltersafterthespecifiedtimeperiod(Firehaz-
ard).
• Cleanthehoodusingadampclothandaneutralliquiddetergent.
The symbol
on the product or on its packaging indicates that this product may not be treated as household waste. In-
stead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed
information about recycling of this product, please contact your local city office, your household waste disposal service or
the shop where you purchased the product.
CHARACTERISTICS
5
CHARACTERISTICS
Dimensions




CHARACTERISTICS
6
Components
Ref. Q.ty Product Components
1 1 Hood Body, complete with: Controls, Light,
Blower, Filters
2 1 Telescopic Chimney comprising:
2.1 1 Upper Section
2.2 1 Lower Section
9 1 Reducer Flange ø 150-120 mm
10 1 Damper ø 150
14.1 2 Air Outlet Connection Extension
15 1 Air Outlet Connection
Ref. Q.ty Installation Components
7.2.1 2 Upper Chimney Section Fixing Brackets
7.3 1 Air Outlet Connection Support
11 6 Wall Plugs
12a 6 Screws 4,2 x 44,4
12c 6 Screws 2,9 x 9,5
Q.ty Documentation
1 Instruction Manual











INSTALLATION
7
INSTALLATION
Wall drilling and bracket fixing
Wall marking:
• Drawaverticallineonthesupportingwalluptotheceiling,orashighaspractical,atthe
centre of the area in which the hood will be installed.
• Drawahorizontallineat450mmabovethehob.
• Placebracket7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit align-
ing the centre (notch) with the vertical reference line.
• Markthewallatthecentresoftheholesinthebracket.
• Placebracket7.2.1 on the wall as shown at X mm below the first bracket (X = height of the
upper chimney section supplied), aligning the centre (notch) with the vertical line.
• Markthewallatthecentresoftheholesinthebracket.
• Markareferencepointasindicatedat116mmfromtheverticalreferencelineand590mm
abovethehorizontalreferenceline.
• Repeatthisoperationontheotherside.
• Drillø8mmholesatallthecentrepointsmarked.
• Insertthewallplugs11intheholes.
• Fixthelowerbracket7.2.1 using the 12a screws (4,2 x 44,4) supplied.
• Fixtheupperbracket7.2.1 and the air outlet connection support 7.3 together using the 2
screws 12a (4,2 x 44,4) supplied.
• Insertthetwoscrews12a (4,2 x 44,4) supplied in the hood body fixing holes, leaving a gap of
5-6 mm between the wall and the head of the screw.









INSTALLATION
8
HOOD BODY MOUNTING
• Beforeattachingthehoodbody, tightenthe
two screws Vr located on the hood body
mounting points.
• Hookthe hood bodyontothescrews12a.
• Fullytighten the supportscrews12a.
• Adjust the screws Vr to level the hood
body.
CONNECTIONS
DUCTED VERSION AIR EXHAUST SYSTEM
When installing the ducted version, connect the
hood to the chimney using either a flexible or
rigid pipe ø 150 or 120mm, the choice of which
is left to the installer.
To install a ø 150
• Toinstallthedumper 10
• Fixthepipe in positionusingsufficientpipe
clamps (not supplied).
To install a ø 120
• Toinstallaø120mmairexhaustconnection,
insert the reducer flange 9 on the dumper
10.
• Fixthepipe in positionusingsufficientpipe
clamps (not supplied)
.• Removeanyactivatedcharcoalfilters.






INSTALLATION
9
RECIRCULATION VERSION AIREOUTLET
• Inserttheconnectionextensionpieceslaterally
14.1 in connection 15.
• Insert the Connector 15 into the Support
bracket 7.3 and fix it with a screw.
• Make sure that the outlet of the extension
pieces 14.1 is horizontally and vertically
aligned with the chimney outlets.
• Connecttheairoutletconnection15 to the
hood body outlet using either a flexible or
rigid pipe ø 150 mm, the choice of which
is left to the installer.
• Ensurethattheactivatedcharcoalfiltershave
been inserted.
ELECTRICAL CONNECTION
• Connect the hood to the mains through a
two-pole switch having a contact gap of at
least 3 mm.
• Remove the grease filters (see paragraph
Maintenance) being sure that the connector
of the feeding cable is correctly inserted in
the socket placed on the side of the fan.
CHIMNEY ASSEMBL
Y
Upper exhaust Chimney
• Slightlywidenthetwosidesoftheupperflue
and hook them behind the brackets 7.2.1,
making sure that they are well seated.
• Securethesidestothebracketsbyusingthe
4 screws 12c (2,9 x 9,5) supplied.
• Make sure that the outlet of the extensions
pieces is aligned with the chimney outlets.
Lower exhaust Chimney
• Slightlywiden thetwosidesof thechimney
and hook them between the upper chimney
and the wall, making sure that they are well
seated.
• Fixthelowerpartlaterallytothehoodbody
using the 2 screws 12c (2,9 x 9,5) supplied.










USE
10
USE
Button Function Display
A
Turns the suction motor on and off at
speed one.
Displays the set speed
B
Decreases the working speed. Displays the set speed
C
Increases the working speed. Displays the set speed
D
Activates intensive speed from any other
speed, including motor off. This speed is set
to operate for 5 minutes, after which the
system returns to the speed that was set
before. Suitable to deal with maximum levels
of cooking fumes.
Displays HI and the time remaining once every
second.
When the filters alarm is triggered, the alarm
can be reset by pressing and holding this
button for ap-proximately 3 seconds. These
indications are only visible when the motor
is turned off.
F indicates the need to wash the metal grease filters.
The alarm is triggered after the Hood has been in
operation for 100 working hours.
C indicates the need to change the activated charcoal
filters, and also to wash the metal grease filters. The
alarm is triggered after the Hood has been in opera-
tion for 200 working hours.
E
Delay function
Activates automatic switch-off with a 20
delay. Suit-able to complete elimination of
residual odours. Can be activated from any
position, and is disabled by pressing the button
or turning the motor off.
Displays the operating speed and the dot at the bottom
right flashes alternately with the remaining time.
Press and hold the button for approximately 5
sec-onds, with all the loads turned off (Motor
and Lights), to turn the Activated Charcoal
Filter alarm On and Off.
- C flashes twice - A.C. Filter alarm Activated.
- C flashes once - A.C. Filter alarm Deactivated
F
Turns the lighting system on and off at
maximum intensity.
MAINTENANCE
11
MAINTENANCE
CLEANING THE COMFORT PANELS
•PulltheComfort Paneltoopenit.
•Disconnect the panel from the hood canopy by
sliding the fixing pin lever.
•The comfort panel must never be washed in a
dishwasher.
•Clean the outside by using a damp cloth and
neutral liquid detergent.
•Clean the inside as well by using a damp cloth
and neutraldetergent;do not use wet cloths or
sponges, or jets of water; do not use abrasive
substances.
•When the above operation has been completed,
hook the panel back to the hood canopy and close
it by turning the knob in the opposite direction.
METAL GREASE FILTERS
Filters can be washed in the dish machine. They need
to be washed when F-sign appears on the display or
in any case every 2 months, or even more frequently
in case of particularly intensive use of the hood.
Alarm reset
•Switchoffthe hoodandthelights.
•PresstheD-key till the display is unlit.
Cleaning the filters
•Pullthecomfort panelstoopenthem.
•Remove the filters one by one pushing them
towards the back side of the hood unit and si-
multaneously pulling downwards.
•Anykindofbendingofthefiltershastobeavoided
when washing them. Before fitting them again
into the hood make sure that they are completely
dry. (The colour of the filter surface may change
through-out the time but this has no influence
to the filter efficiency).
•Whenfittingthefiltersintothehoodpayatten-
tion that they are mounted in correct position the
handle facing outwards.
•Closethecomfort panel.
MAINTENANCE
12
Charcoal filter (recycling version)
This filter cannot be washed or regenerated. It must be replaced when the C appears on the
display or at least once every 4 months. The filter saturation alarm has to be activated already
before.
Activation of the alarm signal
• InRecirculationVersionHoods,theFilterSaturationAlarmmustbeactivatedoninstallation
or at a later date.
• Press and hold button E (Delay) for 5 seconds, until confirmation appears on the display:
• Cflashes twice –ActivatedCharcoalFiltersaturationalarmACTIVATED.
• Cflashes once –ActivatedCharcoalFiltersaturationalarmDEACTIVATED.
REPLACING THE CHARCOAL FILTER
Reset of the alarm signal
• Switchoff the hoodandthelighting.
• PresstheD-key until the display is unlit.
Replacing of the filter
• Openthe comfort panelspullingthemdownwards.
• Removethe metal greasefilters.
• Removethe saturatedcharcoalfilterby releasing
the fixing hooks
• Fitthe new filterandfastenitinits correctposi-
tion.
• Putthe metal greasefiltersin their seats.
• Closethe comfort panels.
Lighting
LIGHT REPLACEMENT
20 W halogen light.
• Removethe 2 screwsfixing theLightingsupport,
and pull it out of from the Hood.
• ExtractthelampfromtheSupport
• Replacewith another ofthesametype,making
sure that the two pins are properly inserted in the
lamp holder socket holes.
• Refitthe Support, fixingitinplacewith the two
screws removed as above.
POUR DES RÉSULTATS PARFAITS
Merci d'avoir choisi ce produit AEG. Nous l'avons créé pour
vous offrir la meilleure performance pour une longue durée,
avec des technologies innovantes qui vous simplifient la
vie-autantdecaractéristiquesquevousnetrouverezpas
sûrementpassurd'autresappareils.Veuillezprendrequel-
ques instants pour lire cette notice afin d'utiliser au mieux
votre appareil.
ACCESSOIRES ET CONSOMMABLES
Danslaboutiqueenligned'AEG,voustrouvereztoutcequ'il
vous faut pour que vos appareils AEG fonctionnent parfai-
tement. Sans oublier une vaste gamme d'accessoires conçus
etfabriquésselonlescritèresdequalitélesplusélevésqui
soient, des articles de cuisine spécialisés aux range-couverts,
des porte-bouteilles aux sacs à linge délicats...
Visit the webshop at:
www.aeg-electrolux.com/shop
14
SOMMAIRE
16
17
19
22
23
RECOMMENDATIONS AND SUGGESTIONS
CHARACTERISTICS
INSTALLATION
USE
MAINTENANCE
SOMMAIRE
CONSEILS ET SUGGESTIONS
15
CONSEILS ET SUGGESTIONS
La présente notice d’emploi vaut pour plusieurs versions de l’appareil. Elle
peut contenir des descriptions d’accessoires ne figurant pas dans votre ap-
pareil.
INSTALLATION
• Lefabricantdéclinetouteresponsabilitéencasdedommagedûàuneinstal-
lationnoncorrecteounonconformeauxrèglesdel’art.
• Ladistanceminimaledesécuritéentreleplandecuissonetlahottedoitêtre
de650mmaumoins(certainsmodèlespeuventêtreinstallésàunehauteur
inférieure : se reporter aux paragraphes « Encombrement » et « Installation »).
• Vérifierquelatensiondusecteurcorrespondàlavaleurquifiguresurlapla-
quette apposée à l’intérieur de la hotte.
• PourlesAppareilsappartenantàlaIèreClasse,veilleràcequelamiseàlaterre
de l’installation électrique domestique ait été effectuée conformément aux
normes en vigueur.
• Connecterlahotteàlasortied’airaspiréàl’aided’unetuyauteried’undiamè-
treégalousupérieurà120mm.Leparcoursdelatuyauteriedoitêtreleplus
court possible.
• Eviterdeconnecterlahotteàdesconduitesd’évacuationdefuméesissues
d’unecombustiontelque(Chaudière,cheminée,etc…).
• Sivousutilisezdesappareilsquinefonctionnentpasàl’électricitédansla
pièceouestinstalléelahotte(parexemple:desappareilsfonctionnantau
gaz),vous devez prévoir uneaérationsuffisantedumilieu. Si lacuisine en
estdépourvue,pratiquezuneouverturequicommuniqueavecl’extérieurpour
garantir l’infiltration de l’air pur.
UTILISATION
• Lahotteaétéconçueexclusivementpourl’usagedomestique,danslebut
d’éliminer les odeurs de la cuisine.
• Nejamaisutiliserabusivementlahotte.
• Nepaslaisserlesflammeslibresàforteintensitéquandlahotteestenser-
vice.
• Toujoursréglerlesflammesdemanièreàévitertoutesortielatéraledeces
dernièresparrapportaufonddesmarmites.
• Contrôlerlesfriteuseslorsdel’utilisationcarl’huilesurchaufféepourraits’en-
flammer.
• Nepaspréparerd’alimentsflambéssouslahottedecuisine:risqued’incen-
die
• Cetappareilnedoitpasêtreutilisépardespersonnes(ycomprislesenfants)
ayant des capacités psychiques, sensorielles ou mentales réduites, ni par des
personnes n’ayant pas l’expérience et la connaissance de ce type d’appareils,
àmoinsd’êtresouslecontrôleetlaformationdepersonnesresponsablesde
leur sécurité.
• Les enfants doivent êtresurveilléspour s’assurerqu’ilsnejouentpasavec
l'appareil.
ENTRETIEN
• Avantdeprocéderàtouteopérationd’entretien,retirerlahotteenretirantla
fiche ou en actionnant l’interrupteur général.
• Effectuer un entretien scrupuleux et en temps dû des Filtres,à la cadence
conseillée (Risque d’incendie).
• Pourlenettoyagedessurfacesdelahotte,ilsuffitd’utiliserunchiffonhumide
et détersif liquide neutre.
Le symbole surleproduitousonemballageindiquequeceproduitnepeutêtretraitécommedéchetménager.Ildoitplutôtêtre
remis au point de ramassage concerné, se chargeant du recyclage du matériel électrique et électronique. En vous assurant que ce produit
estéliminécorrectement,vousfavorisezlapréventiondesconséquencesnégativespourl’environnementetlasantéhumainequi,sinon,
seraientlerésultatd’untraitementinappropriédesdéchetsdeceproduit.Pourobtenirplusdedétailssurlerecyclagedeceproduit,veuillez
prendrecontactaveclebureaumunicipaldevotrerégion,votreserviced’éliminationdesdéchetsménagersoulemagasinoùvousavez
acheté le produit.
CARACTERISTIQUES
16
CARACTERISTIQUES
Encombrement




CARACTERISTIQUES
17
Composants
Réf. Q.té Composants du produit
1 1 Corps Hotte équipé de: Comandes,
Lumière,GroupeVentilateur,Filtres
2 1 Cheminée Télescopique formée de :
2.1 1 Cheminée Supérieure
2.2 1 Cheminée Inférieure
9 1 Flasque de Réduction ø 150-120 mm
10 1 Buse avec clapet
14.1 2 Rallonge Raccord Sortie Air
15 1 Raccord Sortie Air
Réf. Q.té Composants de l’installation
7.2.1 2 Brides Fixation Cheminée Supérieure
7.3 1 Bride Support Raccord
11 6 Chevilles
12a 6 Vis 4,2 x 44,4
12c 6 Vis 2,9 x 9,5
Q.té Documentation
1 Notice d’emploi











INSTALLATION
18
INSTALLATION
Perçage du mur et fixation des équerres
Tracer sur la paroi:
• uneligneverticaleallantjusqu’auplafondouàlalimitesupérieure,aucentredelazonepré-
vuepourlemontagedelahotte;
• unelignehorizontaleà450mmmin.au-dessusduplandecuisson.
• Posercommeindiquéunebride7.2.1 sur la paroi à 1-2 mm du plafond ou de la limite supé-
rieure,enalignantsoncentre(découpes)surlaligneverticalederepère.
• Marquerlescentresdestrousrainurésdelabride.
• Posercommeindiquélabride7.2.1àXmmsouslapremièrebride(X=hauteurcheminée
supérieurefournie),enalignantsoncentre(découpes)surlaligneverticalederepère.
• Marquerlescentresdestrousrainurésdelabride.
• Marquercommeindiqué,unpointderéférenceà116mmdelaligneverticalederepère,et
590mmaudessusdelalignehorizontalederepère.
• Répétercetteopérationsurlecôtéopposé.
• Percerdeø8mmtouslespointsmarqués.
• Insérerleschevilles11danslestrous.
• Fixerlabrideinférieure7.2.1 en utilisant les vis 12a (4,2 x 44,4) fournies.
• Fixerensemblelabridesupérieure7.2.1 et le support 7.3 en utilisant les vis 12a (4,2 x 44,4)
fournies.
• Visserles2vis12a (4,2 x 44,4) fournies dans les trous de fixation du corps hotte, en laissant
unleespacede5-6mmentrelemuretlatêtedelavis









INSTALLATION
19
MONTAGE CORPS HOTTE
• Avant d’accrocher le corps hotte, serrer les
deux vis Vr situées sur les points d’accrochage
du corps hotte.
• Accrocherlecorpshotteauxvis12a prévues
à cet effet.
• Serrer finitivement les vis 12a de sup-
port.
• Agir sur les vis Vr pour niveler le corps
hotte.
BRANCHEMENTS
SORTIE AIR VERSION ASPIRANTE
En cas d’installation en version aspirante, bran-
cher la hotte à la tuyauterie de sortie via un
tube rigide ou flexible de ø 150 ou 120 mm,
au choix de l’installateur.
Branchement avec un tube de ø150
• Insérerlabuseavec clapet 10.
• Fixer le tube par des colliers appropriés. Le
matériau nécessaire n’est pas fourni.
Branchement avec un tube de ø120
• Insérerleflasquederéduction9 sur la buse
avec clapet 10.
• Fixer le tube par des colliers appropriés. Le
matériau nécessaire n’est pas fourni.
• Retirer les éventuels filtres antiodeur au
charbon actif.






INSTALLATION
20
SORTIE AIR VERSION FILTRANTE
•Insérerlatéralementlesrallongesraccord14.1
sur le raccord 15.
• Placer le raccord15 dans l’étrier de soutien
7.3 en le fixant avec une vis.
•S’assurer que la sortie des rallonges raccord
14.1 se trouve au niveau des bouches de
la cheminée aussi bien en horizontal qu’en
vertical.
• Brancher le raccord 15 à la sortie du corps
de la hotte avec un tube rigide ou flexible de
ø 150 mm, selon le choix de l’installateur.
•S’assurerdelaprésencedesfiltresantiodeur
au charbon actif.
BRANCHEMENT ÉLECTRIQUE
• Brancherlahottesurlesecteureninterposant
un interrupteur bipolaire avec ouverture des
contacts d’au moins 3 mm.
• Enleverlesfiltresàgraisse(voir§“Entretien”)
et s’assurer que le connecteur du câble d’ali-
mentation soit bien branché dans la prise du
diffuseur.
MONTAGE CHEMINÉE
Cheminée supérieure
•Elargir légèrement les deux bords latériaux,
et lesaccrocherderrièreslesbrides7.2.1;
refermerjusqu’àlabutée.
•Fixer latéralement aux brides à l’aide des 4
vis 12c fournies.
•S’assurer que la sortie des rallonges raccord
se trouve au niveau des bouches de la che-
minée.
Cheminée inférieure
• Elargirlégèrementlesdeuxbordslatériauxde
la Cheminée et les accrocher entre la Chemi-
néesupérieureetlaparoi;refermerjusqu’àla
butée.
• Fixerlatéralementlapartieinférieureaucorps
hotte, à l’aide des deux 2 vis 12c fournie
s.






  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

AEG DD8694-M Manuel utilisateur

Catégorie
Hottes
Taper
Manuel utilisateur