Hitachi NV 83A3 Instruction And Safety Manual

Catégorie
Cloueuse
Taper
Instruction And Safety Manual
Instruction and safety manual
Manuel d’instructions et de sécurité
Instrucciones y manual de seguridad
Model
Modèle
Modelo
NV 83A3
Nailer
Cloueur
Clavador
DANGER
Improper use of this Nailer can result in death or serious injury!
This Manual contains important information about product safety.
Read and understand this Manual before operating the Nailer.
Never allow anyone who has not reviewed this manual.
DANGER
Une utilisation incorrecte et sans respecter la sécurité de ce cloueur risque dentraîner la
mort ou des blessures graves !
Ce manuel renferme des instructions importantes sur la sécurité de loutil.
Lire et bien assimiler ce manuel avant d’utiliser le cloueur.
Ne jamais laisser les personnes n’ayant pas étutdié le manuel utiliser l’outil.
PELIGRO
¡La utilización inadecuada e insegura de este clavador puede resultar en lesiones serias o
en la muerte!
Este manual contiene información importante sobre la seguridad del producto.
Lea y entienda este manual antes de utilizar el martillo neumático.
No deje manejar esta herramienta a nadie que no haya leído este manual.
English
Page Page
Français
Page Page
Español
Página Página
CONTENTS
TABLE DES MATIÈRES
ÍNDICE
IMPORTANT SAFETY INFORMATION ....................3
DEFINITIONS OF SIGNAL WORDS .........................3
EXPLANATION OF THE NAILING ACTION
OF THE HITACHI NAILER ...................................3
SAFETY
IMPORTANT SAFETY INSTRUCTION FOR USING
NAI LER S ..............................................................4
IMPORTANT SAFETY INSTRUCTION FOR USING
NV83A3 COIL NAILER ........................................7
EMPLOYER’S RESPONSIBILITIES .........................7
OPERATION
NAME OF PARTS .....................................................8
SPECIFI CAT IONS .....................................................9
NAIL SELECTION .....................................................9
ACCESSORIES.........................................................9
STANDARD ACCESSORIES...............................9
OPTIONAL ACCESSORIES ..............................10
APPLICATIONS ...................................................... 10
BEFORE OPERATION ............................................10
WORKING ENVIRONMENT .............................. 10
AIR SUPPLY ...................................................... 10
LUBRICATION ................................................... 11
COLD WEATHER CARE ................................... 11
TESTING THE NAILER ..................................... 11
ADJUSTING AIR PRESSURE ........................... 12
LOADING NAILS ............................................... 13
NAILER OPERATION .............................................14
METHODS OF OPERATION ............................. 14
ADJUSTING THE NAILING DEPTH ..................16
MAINTENANCE
MAINTENANCE AND INSPECTION ......................17
SERVICE AND REPAIRS ........................................ 18
PARTS LIST ............................................................58
INFORMATION IMPORTANTE DE SÉCURI......20
DEFINITION DES MOTS DE SIGNALISATION ......20
EXPLICATION DE LACTION DE CLOUAGE DU
CLOUEUR HITACHI ..........................................20
SECURITE
CONSIGNES DE SECURITE IMPORTANTES
POUR LUTILISATION DU CLOUEUR ...............21
IMPORTANTES INSTRUCTIONS DE
SECURITE POUR LUTILISATION DU
CLOUEUR NV83A3 ........................................... 24
RESPONSABILITES DE L’EMPLOYEUR ...............24
UTILISATION
NOM DES PIECES ..................................................25
SPECIFI CAT IONS ...................................................26
SELECTION DES CLOUS ......................................26
ACCESSORIES.......................................................26
ACCESSOIRES STANDARD.............................26
ACCESSOIRES EN OPTION ............................27
APPLICATIONS ......................................................27
AVANT LUTILISATION ...........................................27
ENVIRONNEMENT DE TRAVAIL ......................27
ALIMENTATION D’AIR .......................................27
GRAISSAGE ......................................................28
ENTRETIEN PAR TEMPS FROID .....................28
ESSAI DU CLOUEUR ........................................28
RÉGLAGE DE LA PRESSION DAIR .................30
CHARGEMENT DES CLOUS ............................30
UTILISATION DU CLOUEUR ..................................31
THODES D’UTILISATION ............................32
RÉGLAGE DE LA PROFONDEUR DE
CLOUAGE ....................................................34
ENTRETIEN
ENTRETIEN ET INSPECTION ................................35
ENTRETIEN ET REPARATIONS ............................37
LISTE DES PIÈCES ................................................58
INFORMACIÓN IMPORTANTE SOBRE
SEGU RIDAD ......................................................3 9
DEFINICIÓN DE LAS PALABRAS CLAVE .............39
EXPLICACIÓN LA ACCIÓN DE CLAVADO DEL
CLAVADOR HITACHI ........................................39
SEGURIDAD
INSTRUCCIONES IMPORTANTES DE
SEGURIDAD PARA LA UTILIZACIÓN DEL
CLAVADOR .......................................................40
INSTRUCCIONES IMPORTANTES DE
SEGURIDAD PARA UTILIZAR EL CLAVADOR
DE RISTRA NV83A3 .........................................43
RESPONSABILIDADES DEL EMPRESARIO .........43
OPERACIÓN
NOMENCLATURA .................................................. 44
ESPECIFICACIONES .............................................45
SELECCIÓN DE CLAVOS ......................................45
ACCESORIOS ........................................................45
ACCESORIOS ESTÁNDAR ...............................45
ACCESORIOS OPCIONALES...........................46
APLICACIONES ...................................................... 46
ANTES DE LA OPERACIÓN ...................................46
ENTORNO DE TRABAJO .................................46
SUMINISTRO DE AIRE .....................................46
LUBRICACIÓN .................................................. 47
CUIDADOS PARA CLIMAS FRÍOS ...................47
PRUEBA DEL CLAVADOR ................................47
AJUSTE DE LA PRESIÓN DE AIRE ..................49
CARGA DE CLAVOS .........................................49
OPERACIÓN DEL CLAVADOR ..............................50
TODOS DE OPERACIÓN ............................ 51
AJUSTE DE LA PROFUNDIDAD DE
CLAVADO.....................................................53
MANTENIMIENTO
MANTENIMIENTO E INSPECCIÓN .......................54
SERVICIO Y REPARACIONES ...............................56
LISTA DE PIEZAS ..................................................58
3
English
IMPORTANT SAFETY INFORMATION
Read and understand tool labels and all of the operating instructions, safety precautions and warnings
in this manual before operating or maintaining this nailer.
Failure to follow warnings could result in DEATH or SERIOUS INJURY
Most accidents that result from the operation and maintenance of Nailers are caused by the failure to observe basic
safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it
occurs, and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Manual and in the sections which contain the
operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identi ed by DANGERS and WARNINGS
on the Nailer and in this Manual.
NEVER use this Nailer for applications other than those speci ed in this Manual.
DEFINITIONS OF SIGNAL WORDS
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or
may cause machine damage.
NOTE emphasizes essential information.
EXPLANATION OF THE NAILING ACTION OF THE HITACHI NAILER
SINGLE SEQUENTIAL ACTUATION MECHANISM:
First, press the push lever against the wood; next, pull the trigger to drive the nail.
First, pull the trigger; next, press the push lever against the wood to drive the nail.
After nailing once, nailing will not be possible again until the trigger is released and pressed again.
CONTACT ACTUATION MECHANISM:
First, press the push lever against the wood; next, pull the trigger to drive the nail.
First, pull the trigger; next, press the push lever against the wood to drive the nail.
If the trigger is held back, a nail will be driven each time the push lever is pressed against the wood.
4
English
SAFETY
IMPORTANT SAFETY INSTRUCTION FOR USING NAILERS
READ ALL INSTRUCTIONS
DANGER
1. OPERATORS AND OTHERS IN WORK AREA
MUST WEAR SAFETY GLASSES WITH SIDE
SHIELDS.
When operating the Nailer, always wear
safety glasses with side shields, and
make sure others in work area wear
safety glasses, too.
Safety glasses must conform to the
requirements of American National
Standards Institute, ANSI Z87.1 and
provide protection against ying particles
both from the front and side.
WARNING
3. NEVER POINT TOOL AT YOURSELF OR OTHERS
IN WORK AREA.
Always assume the Nailer contains
fasteners.
Never point the Nailer at yourself toward
yourself or others, whether it contains
fasteners or not.
If fasteners are mistakenly driven, it can
lead to severe injuries.
Never engage in horseplay with the
Nailer.
Respect the Nailer as a working
implement.
4. KEEP FINGERS AWAY FROM TRIGGER
WHEN NOT DRIVING FASTENERS TO AVOID
ACCIDENTAL FIRING.
Never carry the Nailer with nger on trigger since
you could drive a fastener unintentionally and injure
yourself or someone else.
Always carry the Nailer by the handle only.
5. CHOICE OF TRIGGERING METHOD IS
IMPORTANT.
Read and understand section titled “METHODS OF
OPERATION.” (pages 14 – 16)
The employer must enforce the use of safety glasses
by the Nailer operator and others in work area.
2. NEVER USE OXYGEN OR OTHER BOTTLED
GASES. EXPLOSION MAY OCCUR.
Never use oxygen, combustible gases
or any other bottled gases as a power
source for the Nailer.
Use of the above gases is dangerous, as
the Nailer will explode.
Use only clean, dry, regulated
compressed air.
6. DO NOT EXCEED 120 psi. (8.3 bar 8.5 kgf/cm
2
)
Do not exceed maximum
recommended air
pressure 120 psi (8.3 bar
8.5 kgf/cm
2
).
Never connect the
Nailer to pressure which
potentially exceeds 200
psi (13.7 bar 14 kgf/cm
2
)
as the Nailer can burst.
7. ALWAYS WEAR EAR AND HEAD PROTECTION.
Always wear ear protection to protect your ears from
loud noise.
Always wear head protection to protect your head
from ying objects.
8. STORE NAILER PROPERLY.
When not in use, the Nailer should be stored in a dry
place. Keep out of reach of children. Lock the storage
area.
9. KEEP WORK AREA CLEAN.
Cluttered areas invite injuries. Clear all work areas of
unnecessary tools, debris, furniture, etc.
5
English
10. NEVER USE IN PRESENCE OF FLAMMABLE
LIQUIDS OR GASES.
The Nailer produces sparks during operation.
Never use the Nailer in sites containing lacquer,
paint, benzine, thinner, gasoline, gases, adhesive
agents, and other materials which are combustible or
explosive.
11. KEEP VISITORS AWAY.
Do not let visitors handle the Nailer.
All visitors should be kept safely away from work
area.
12. DRESS PROPERLY.
Do not wear loose clothing or jewelry as they can be
caught in moving parts.
Rubber gloves and nonskid footwear are
recommended when working outdoors.
Wear protective hair covering to contain long hair.
13. NEVER USE NON RELIEVING COUPLER ON
NAILER.
If a non relieving coupler is used on the Nailer,
the Nailer can remain charged with air after
disconnecting and thus will be able to drive a fastener
even after disconnecting.
The Nailer and air hose must have a hose coupling
such that all pressure is removed from the Nailer
when the coupling joint is disconnected.
14. CHECK PUSH LEVER BEFORE USE.
Make sure the push lever operates properly.
(The push lever may be called “Safety.) Never
use the Nailer unless the push lever is operating
properly, otherwise the Nailer could drive a fastener
unexpectedly. Do not tamper with or remove the push
lever, otherwise the push lever becomes inoperable.
15. KEEP ALL SCREWS AND COVERS TIGHTLY IN
PLACE.
Keep all screws and covers tightly mounted. Check
their condition periodically.
Never use the Nailer if parts are missing or damaged.
16. DO NOT LOAD FASTENERS WITH TRIGGER OR
PUSH LEVER DEPRESSED.
When loading fasteners into the Nailer or when
connecting the air hose,
1) do not depress the trigger;
2) do not depress the push lever; and
3) keep the Nailer pointed downward.
17. KEEP HANDS AND FEET AWAY FROM FIRING
HEAD DURING USE.
Never place your hands or feet closer than 8 inches
(200 mm) from the ring head.
A serious injury can result if the fasteners are
de ected by the workpiece, or are driven away from
the point of entry.
18. PLACE NAILER PROPERLY ON WORKPIECE.
Do not drive fasteners on top of other fasteners or
with the Nailer at too steep of an angle; the fasteners
can ricochet and hurt someone.
19. BEFORE STARTING WORK, CHECK THE
NAILING OPERATION SWITCHING DEVICE.
This Hitachi nailer includes a nailing operation
switching device.
Before starting work, check the setting of the
operation switching device.
If the switching device is not set properly, the nailer
will not operate correctly.
20. BE CAREFUL OF DOUBLE FIRE DUE TO RECOIL.
If the push lever is unintentionally allowed to re-contact
the workpiece following recoil, an unwanted fastener
will be driven.
In order to avoid this undesirable double re,
Intermittent operation (Trigger ring)
1) Set the switching device to SINGLE SEQUENTIAL
ACTUATION MECHANISM.
2) Pull the trigger rapidly and rmly.
Continuous operation (Push lever ring)
1) Do not press the nailer against the wood with
excessive force.
2) Separate the nailer from the wood as it recoils
after nailing.
21. DO NOT DRIVE FASTENERS INTO THIN
BOARDS OR NEAR CORNERS AND EDGES OF
WORKPIECE.
The fasteners can be driven through or away from the
workpiece and hit someone.
SAFETY — Continued
WARNING
6
English
22. NEVER DRIVE FASTENERS FROM BOTH SIDES
OF A WALL AT THE SAME TIME.
The fasteners can be driven into and through the wall
and hit a person on the opposite side.
23. CHECK FOR LIVE WIRES.
Avoid the risk of severe electrical shock by checking
for live electrical wires that may be hidden by walls,
oors or ceilings. Turn o the breaker switch to
ensure there are no live wires.
24. NEVER CARRY NAILER BY HOSE.
25. DO NOT OVERREACH.
Keep proper footing and balance at all times.
26. NEVER USE NAILER WHICH IS DEFECTIVE OR
OPERATING ABNORMALLY.
If the Nailer appears to be operating unusually,
making strange noises, or otherwise appears
defective, stop using it immediately and arrange for
repairs by a Hitachi authorized service center.
27. DO NOT DISCONNECT AIR HOSE FROM NAILER
WITH FINGER ON TRIGGER.
The Nailer can re when re-connected to an air supply.
28. DISCONNECT AIR HOSE FROM NAILER WHEN:
1) doing maintenance and inspection;
2) clearing a jam;
3) it is not in use;
4) leaving work area;
5) moving it to another location; and
6) handing it to another person.
Never attempt to clear a jam or repair the Nailer
unless you have disconnected air hose from the
Nailer and removed all remaining fasteners from the
Nailer.
The Nailer should never be left unattended since
people who are not familiar with the Nailer might
handle it and injure the themselves.
29. STAY ALERT.
Watch what you are doing. Use common sense.
Do not operate the Nailer when you are tired.
The Nailer should never be used by you if you are
under the in uence of alcohol, drugs or medication
that makes you drowsy.
30. HANDLE NAILER CORRECTLY.
Operate the Nailer according to this Manual.
Never allow the Nailer to be operated by children,
individuals unfamiliar with its operation or unauthorized
personnel.
31. NEVER USE NAILER FOR APPLICATIONS OTHER
THAN THOSE SPECIFIED IN THIS MANUAL.
32. HANDLE NAILER CAREFULLY.
Because of high air pressure in the Nailer, cracks in
the surface are dangerous.
To avoid this, do not drop the Nailer or strike the Nailer
against hard surfaces; and do not scratch or engrave
signs on the Nailer. Handle the Nailer carefully.
33. MAINTAIN NAILER WITH CARE.
Keep the Nailer clean and lubricated for better and
safer performance.
34. USE ONLY PARTS, ACCESSORIES OR
FASTENERS SUPPLIED OR RECOMMENDED BY
HITACHI.
Unauthorized parts, accessories, or fasteners may
void your warranty and can lead to malfunction and
resulting injuries.
Only service personnel trained by Hitachi, distributor
or employer shall repair the Nailer.
35. NEVER MODIFY OR ALTER A NAILER.
Doing so may cause it to malfunction and personal
injuries may result.
SAFETY — Continued
WARNING
7
English
SAFETY — Continued
IMPORTANT SAFETY INSTRUCTIONS FOR USING NV83A3 COIL NAILER
WARNING
1. DO NOT REMOVE DUST COVER.
Fragments of wire collating fasteners can y out.
2. CLOSE NAIL GUIDE AND DO NOT OPEN IT
DURING OPERATION.
If driving fasteners with the nail guide open, the
fasteners can be driven away from the workpiece.
EMPLOYER’S RESPONSIBILITIES
1. Ensure that this MANUAL is available to operators
and personnel performing maintenance.
2. Ensure that Nailers are used only when operators and
others in work area are wearing EYE PROTECTION.
3. Enforce the use of EYE PROTECTION by operators
and others in work area.
4. Keep Nailers in safe working order.
5. Maintain Nailers properly.
6. Ensure that Nailers which require repair are not
further used before repair.
SAVE THIS MANUAL AND
KEEP IT AVAILABLE FOR OTHERS!
8
English
OPERATION
NOTE: The information contained in this Manual is designed to assist you in the safe operation of the Nailer.
Some illustrations in this Manual may show details or attachments that di er from those on your own Nailer.
NAME OF PARTS
Nailing operation switching device
Switching
Device
Switching
Device
SINGLE SEQUENTIAL
ACTUATION MECHANISM
(Switching device:
leftward position)
CONTACT ACTUATION
MECHANISM
(Switching device:
rightward position)
Nose
Piston
Piston O-ring
Exhaust Cover
Driver Blade
Main Nail Stopper
Adjuster
Outlet (Firing Head)
Body
Trigger
Cap
Magazine Cover
Nail Holder
Magazine Assembly
Dust Cover
Air Plug
Enlarged view of the valve part
Valve part
Switching Device
Valve Bush
Knob
Push Lever (A)
Trigger
Magazine
Section A – A
Nail Guide
Feeder
Feed Piston
Feed Spring
A
A
9
English
SPECIFICATIONS
Operating pressure 70 – 120 psi (4.9 – 8.3 bar 5 – 8.5 kgf/cm
2
)
Dimensions
Length × Height × Width
12-13/32" × 13-11/16" × 5-13/32"
(315 mm × 348 mm × 137 mm)
Weight 8.2 lbs (3.7 kg)
Nail capacity 200 – 300 nails (1 coil)
Air consumption
.088 ft
3
/cycle at 100 psi
(2.5 ltr/cycle at 6.9 bar)
(2.5 ltr/cycle at 7 kgf/cm
2
)
Air inlet 3/8 NPT Thread
NAIL SELECTION
WARNING
Be sure to use only the genuine HITACHI nails for the NV83A3. The use of any other nails can result in
tool malfunction and/or nail breakdown, leading to serious injuries.
Only nails shown in the Table below can be driven with this Nailer.
Wire-collated coil nails
Min. Max.
.099"
(2.5 mm)
2" (50 mm)
.236"
(6 mm)
.131"
(3.3 mm)
3-1/4" (83 mm)
.283"
(7.2 mm)
ACCESSORIES
WARNING
Accessories other than those shown below can lead to malfunction and resulting injuries.
STANDARD ACCESSORIES
1
1
Eye protection ..........................................................1
10
English
OPTIONAL ACCESSORIES
... sold separately
Pneumatic Tool Lubricant
.8 oz. (25 cc) oil feeder (Code No. 877153)
4 oz. (120 cc) oil feeder (Code No. 874042)
1 quart (1 ltr) can (Code No. 876212)
NOTE: Accessories are subject to change without any
obligation on the part of HITACHI.
APPLICATIONS
Construction wooden work such as oor and wall
framing, roof decking, sub ooring.
Mobile and modular home construction.
Making wooden boxes, palettes, and drums.
Packing operations in manufacturing plants, and
other types of packing and crating work in general.
BEFORE OPERATION
Read section titled “SAFETY” (pages 4 – 7).
Make sure of the followings before operation.
WORKING ENVIRONMENT
WARNING
No ammable gas, liquid or other ammable
objects at worksite.
Clear the area of children or unauthorized
personnel.
AIR SUPPLY
DANGER
NEVER use oxygen or other
bottled gases. Explosion may
occur.
WARNING
Never connect Nailer to pressure
which potentially exceeds 200 psi
(13.7 bar 14 kgf/cm
2
).
Never use non relieving coupler on Nailer.
1. Power source
Use only clean, dry, regulated compressed air as a
power source for this Nailer.
Air compressors used to supply compressed air to
this Nailer must comply with the requirements of
the latest version of ANSI Standard B 19.3 “Safety
Standard For Compressors For Process Industries.
Moisture or oil in the air compressor may accelerate
wear and corrosion in the Nailer.
Drain daily.
2. Filter-Regulator-Lubricator
Use a regulator with a pressure range of 0 – 120 psi
(0 – 8.3 bar 0 – 8.5 kgf/cm
2
).
Filter-regulator-lubricator units supply an optimum
condition for the Nailer and extend the Nailer life.
These units should always be used.
Filter ............ The lter removes moisture and dirt
mixed in compressed air.
Drain daily unless tted with an
automatic drain.
Keep the lter clean by regular
maintenance.
Regulator ......The regulator controls the operating
pressure for safe operation of the Nailer.
Inspect the regulator before operation to
be sure it operates properly.
Lubricator .... The lubricator supplies an oil mist to the
Nailer.
Inspect the lubricator before operation
to be sure the supply of lubricant is
adequate.
Use Hitachi pneumatic tool lubricant.
Nailer Side
Filter
Lubricator
Compressor Side
Regulator
3. Air hose
Air hose must have a minimum working pressure
rating of 150 psi (10.4 bar 10.6 kgf/cm
2
) or 150%
of the maximum pressure produced in the system,
whichever is higher.
4. Air consumption
Using the Air consumption table and the Air
compressor size formula, nd a correct compressor
size.
11
English
Air consumption table
Operating pressure
psi
(bar)
(kgf/cm
2
)
80
(5.5)
(5.6)
90
(6.2)
(6.3)
100
(6.9)
(7)
Air consumption
ft
3
/cycle
(Itr/cycle)
.062
(1.7)
.075
(2.1)
.088
(2.5)
Air compressor size formula
Amount of air required
=number of Nailers
× average nails driven each minute per Nailer
× air consumption at given air pressure
× safety factor (always 1.2)
Example: 2 Nailers operating at 100 psi driving 30
nails per minute
Amount of air required
=2 × 30 × .088 (2.5) × 1.2
=6.3 CFM (ft
3
/min) (180 ltr/min)
After making the calculations as shown above, you
should nd a compressor providing 6.3 CFM of air
that is required.
LUBRICATION
It is important that the Nailer be properly lubricated.
Without proper lubrication, the Nailer will not work
properly and parts will wear prematurely.
Use Hitachi pneumatic tool lubricant.
Do not use detergent oil or additives. These lubricants
will harm the O-rings and other rubber parts. This will
cause the Nailer to malfunction.
Filter-regulator-lubricator units should always be
used.
Keep the lubricator lled with Hitachi pneumatic tool
lubricant.
If a lubricator is not available, supply 5 – 10 drops of
Hitachi pneumatic tool lubricant into the air plug on
the Nailer twice a day.
COLD WEATHER CARE
Do not store the Nailer in a cold weather environment.
Keep the Nailer in a warm area until beginning the
work.
If the Nailer is already cold, bring it in a warm area
and allow the Nailer to warm up before use.
1
Reduce the air pressure to 64 psi (4.4 bar
4.5 kgf/cm
2
).
2
Remove all nails from the Nailer.
3
Connect the air hose and free- re (blank- re) the
Nailer.
The lowered air pressure will be enough to free-
re the Nailer.
Slow speed operation tends to warm up the
moving part.
CAUTION
Do not free- re the Nailer at high pressure.
TESTING THE NAILER
DANGER
Operators and others in work
area MUST wear safety
glasses with side shields
which conforms to ANSI Z87.1
speci cations.
WARNING
Never use Nailer unless push lever is
operating properly.
Before actually beginning the nailing work, test the Nailer
by using the checklist below. Conduct the tests in the
following order.
If abnormal operation occurs, stop using the Nailer and
contact a Hitachi authorized service center immediately.
(1) DISCONNECT AIR HOSE FROM NAILER.
REMOVE ALL NAILS FROM NAILER.
ALL SCREWS MUST BE TIGHTENED.
If any screws are loose, tighten them.
THE PUSH LEVER AND TRIGGER MUST MOVE
SMOOTHLY.
Push Lever
Trigger
Do not connect
air hose
12
English
(2) Adjust the air pressure to 70 psi (4.9 bar 5 kgf/cm
2
).
Connect the air hose.
Do not load any nails in the Nailer.
Set the switching device to the leftward position
(SINGLE SEQUENTIAL ACTUATION MECHANISM).
(Set the switching device to the leftward position
completely as shown in the diagram. Otherwise, it will
not operate properly.)
Leftward position
Switching device
THE NAILER MUST NOT LEAK AIR.
(3) Remove the nger from the trigger and press the
push lever against the wood.
THE NAILER MUST NOT OPERATE.
Do not pull Trigger
Depress Push Lever
(4) Separate the push lever from the wood.
Next, point the nailer downward, pull the trigger and
then wait in that position for 5 seconds or longer.
THE NAILER MUST NOT OPERATE.
Pull Trigger
(5)
1
Without touching the trigger, depress the push
lever against the workpiece.
Pull the trigger.
THE NAILER MUST OPERATE.
2
Hold the trigger back while separating the push
lever from the wood.
The nailer will remain in operated status (the
driver blade will remain at the bottom).
3
Remove the nger from the trigger.
Nailer operation will end (the driver blade will
return to the top).
(6) Set the switching device to the rightward position
(CONTACT ACTUATION MECHANISM).
(Set the switching device to the rightward position
completely as shown in the diagram. Otherwise, it will
not operate properly.)
Rightward position
Switching device
With the Nailer o the workpiece, pull the trigger.
Depress the push lever against the workpiece.
THE NAILER MUST OPERATE.
(7) If no abnormal operation is observed, you may load
nails in the Nailer.
Drive nails into the workpiece that is the same type to
be used in the actual application.
THE NAILER MUST OPERATE PROPERLY.
ADJUSTING AIR PRESSURE
WARNING
Do not exceed
120 psi (8.3 bar
8.5 kgf/cm
2
).
13
English
1
Turn the nail holder about 90 degrees
counterclockwise.
2
Slide in vertical direction possible.
Lift or lower the nail holder to accept di erent
length nails.
3
Adjust the plate to the nail length reference points
on the magazine cover and turn the nail holder 90
degrees clockwise until you hear "click".
Nail holder
Magazine
3
1
2
2"
2
1
/4" 2
3
/8"
2
1
/2" 2
3
/4"
3" 3
1
/4"
(3) Place the nail coil into the magazine.
Uncoil enough nails to reach the driving hole.
Magazine
Nail holder
Nails
(4)
1
Uncoil enough nails to reach the driving hole.
2
Insert the rst nail into the driving hole and the
second nail between the two pawls of the feeder.
3
Fit the nail heads in the guide slot.
Nail Guide
First nail
3
1
2
4
2
Feeder
Guide surface
Driving hole
Guide slot
4
Pulling the nails to the right, swing the nail guide
closed.
Adjust the air pressure at recommended operating
pressure 70 – 120 psi (4.9 – 8.3 bar 5 – 8.5 kgf/cm
2
)
according to the length of nails and the hardness of
workpiece.
The correct air pressure is the lowest pressure which will
do the job. Using the Nailer at a higher than required air
pressure unnecessarily over stresses the Nailer.
LOADING NAILS
WARNING
When loading nails into Nailer,
1) do not pull trigger;
2) do not depress push lever; and
3) keep Nailer pointed downward.
(1) Grip the nail guide and knob with nger.
Press the knob down and swing the nail guide open.
And open the magazine cover.
Knob
Nail guide
Magazine cover
(2) Adjust the position of the plate according to the nail
length.
The nail will not feed smoothly if the plate is not
correctly adjusted.
Magazine
Nail holder
Magazine cover
NOTE: Before loading nails in the magazine, adjust
the plate. If the magazine cover is forcibly
closed without adjusting the plate correctly,
the nail holder may be damaged.
14
English
(5) Close the magazine cover rst and swing the nail
guide closed.
(6) Lock the knob correctly.
Magazine cover
Nail guide
Knob
NOTE: Be careful not to deform the collated wires and
not to disengage the nails with the guide surface.
Otherwise, the nail guide will not close correctly.
NAILER OPERATION
Read section titled “SAFETY” (pages 4 – 7).
DANGER
Operators and others in work
area MUST wear safety
glasses with side shields
which conforms to ANSI Z87.1
speci cations.
WARNING
NEVER point tool at yourself or others in
work area.
Keep ngers AWAY from trigger when not
driving nails to avoid accidental ring.
Choice of triggering method is important.
Please read and understand “Methods of
Operation” below.
Before starting work, check the nailing
operation switching device.
This Hitachi nailer includes a nailing
operation switching device.
Before starting work, make sure that the
switching device is properly set.
If the switching device is not set properly, the
nailer will not operate correctly.
Never place your hands or feet closer than 8
inches (200 mm) from ring head when using.
Do not drive nails on top of other nails or
with Nailer at too steep of an angle; nails can
ricochet and hurt someone.
Do not drive nails into thin boards or near
corners and edges of workpiece. Nails can be
driven through or away from workpiece and
hit someone.
Never drive nails from both sides of a wall
at the same time. Nails can be driven into
and through the wall and hit a person on the
opposite side.
Never use Nailer which is defective or
operating abnormally.
Do not use Nailer as hammer.
Disconnect air hose from Nailer when:
1) it is not in use;
2) leaving work area;
3) moving it to another location; and
4) handing it to another person.
This Hitachi nailer is equipped with a nailer operation
switching device.
Use SINGLE SEQUENTIAL ACTUATION MECHANISM or
CONTACT ACTUATION MECHANISM in accordance with
the work to be performed.
Explanation of the various nailing operations
SINGLE SEQUENTIAL ACTUATION MECHANISM:
First, press the push lever against the wood; next,
pull the trigger to drive the nail.
After nailing once, nailing will not be possible again
until the trigger is released and pressed again.
CONTACT ACTUATION MECHANISM: First, press
the push lever against the wood; next, pull the trigger
to drive the nail.
First, pull the trigger; next, press the push lever
against the wood to drive the nail.
If the trigger is held back, a nail will be driven each
time the push lever is pressed against the wood.
METHODS OF OPERATION
This Nailer is equipped with the push lever and does
not operate unless the push lever is depressed (upward
position).
There are two methods of operation to drive nails with this
Nailer.
They are:
1. Intermittent operation (Trigger re):
2. Continuous operation (Push lever re):
15
English
(1) Intermittent operation (Trigger re)
Use the SINGLE SEQUENTIAL ACTUATION
MECHANISM setting.
WARNING
For intermittent operation, set the switching
device to the leftward position completely.
(i.e. Set to SINGLE SEQUENTIAL ACTUATION
MECHANISM.)
To avoid double ring or accidental ring due
to recoil.
1) Set the switching device to SINGLE
SEQUENTIAL ACTUATION MECHANISM.
2) Pull the trigger rapidly and rmly.
1
Set the switching device to the leftward position
(to set to SINGLE SEQUENTIAL ACTUATION
MECHANISM).
(Set the switching device to the leftward position
completely as shown in the diagram. Otherwise,
it will be set to CONTACT ACTUATION
MECHANISM.)
2
Position the nail outlet on the workpiece with
nger o the trigger.
3
Depress the push lever rmly until it is completely
depressed.
4
Pull the trigger to drive a nail.
5
Remove nger from the trigger.
To continue nailing in a separate location, move the nailer
along the wood, repeating steps
2
5
as required.
1
Leftward position
Switching device
Push Lever
3
4
Trigger
WARNING
A nail will re each time the trigger is
depressed as long as the push lever remains
depressed.
(2) Continuous operation (Push lever re)
Using CONTACT ACTUATION MECHANISM
WARNING
To avoid double ring or accidental ring due
to recoil.
1) Do not press the nailer against the wood with
excessive force.
2) Separate the nailer from the wood as it
recoils after nailing.
1
Set the switching device to the rightward position
(to set to CONTACT ACTUATION MECHANISM).
(Set the switching device to the rightward position
completely as shown in the diagram. Otherwise, it
will not operate properly.)
2
Pull the trigger with the Nailer o the workpiece.
3
Depress the push lever against the workpiece to
drive a nail.
4
Move the Nailer along the workpiece with a
bouncing motion.
Each depression of the push lever will drive a nail.
As soon as the desired number of nails have been
driven, remove nger from the trigger.
1
Rightward position
Switching device
Previously pull
the trigger
2
4
16
English
WARNING
Keep your nger o the trigger except during
fastening operation, because serious injury
could result if the push lever accidentally
contacts you or others in work area.
Keep hands and body away from the
discharge area. This Hitachi nailer may
bounce from the recoil of driving a fastener
and unwanted subsequent fastener may be
driven, possibly causing injury.
Some types of loaded nails can spark out of
the muzzle during a nail driving operation.
Exercise caution!
The SINGLE SEQUENTIAL ACTUATION MECHANISM
is for use where precision fastener placement is desired.
The SINGLE SEQUENTIAL ACTUATION MECHANISM
may reduce the possibility of bodily injury to you or others
in the work area compared to the CONTACT ACTUATION
MECHANISM. This is because it is less likely to drive
an unwanted nail if you keep the trigger pulled and
accidentally bump the push lever against yourself or
others.
The SINGLE SEQUENTIAL ACTUATION MECHANISM
may also reduce the speed of operation compared
to the CONTACT ACTUATION MECHANISM. The
SINGLE SEQUENTIAL ACTUATION MECHANISM is
recommended to inexperienced users.
NOTE:
If all warnings and instructions are followed, safe
operation is possible with two systems: SINGLE
SEQUENTIAL ACTUATION MECHANISM and
CONTACT ACTUATION MECHANISM.
Always handle nails and package carefully. If nails
are dropped, collating paper may be broken.
After nailing:
1) disconnect air hose from the Nailer;
2) remove all nails from the Nailer;
3) supply 5 – 10 drops of Hitachi pneumatic tool
lubricant into the air plug on the Nailer; and
4) open the petcock on the air compressor tank to
drain any moisture.
ADJUSTING THE NAILING DEPTH
WARNING
Disconnect the air hose from the nailer
before turning the adjuster.
To assure that each nail penetrates to the same depth, be
sure that:
1) the air pressure to the Nailer remains constant
(regulator is installed and working properly), and
2) the Nailer is always held rmly against the workpiece.
If nails are driven too deep or shallow into the workpiece,
adjust the nailing in the following order.
1
DISCONNECT AIR HOSE FROM NAILER
Disconnect
air hose
15
Adjuster
Deep
Shallow
2
If nails are driven too deep, turn the adjuster to the
shallow side.
Adjustments are in half-turn increments.
2
Too Deep
Turn Adjuster
Flush
If nails are driven too shallow, turn the adjuster to the
deep side.
Turn Adjuster
Flush
2
Too Shallow
3
Stop turning the adjuster when a suitable position is
reached for a nailing test.
4
Connect the air hose.
ALWAYS WEAR EYE PROTECTION.
Perform a nailing test.
5
DISCONNECT AIR HOSE FROM NAILER.
6
Choose a suitable position for the adjuster.
17
English
MAINTENANCE
NOTE: The information contained in this Manual is designed to assist you in the safe maintenance of the Nailer.
Some illustrations in this Manual may show details or attachments that di er from those on your own Nailer.
MAINTENANCE AND INSPECTION
Read section titled “SAFETY” (pages 4 – 7).
WARNING
Disconnect air hose and remove all nails
from Nailer when:
1) doing maintenance and inspection; and
2) clearing a jam.
1. Clearing a jam
Remove a jammed nail in the following order:
1
DISCONNECT AIR HOSE.
2
Open the nail guide.
3
Insert a rod into the outlet.
Tap the rod with a hammer.
Hammer
Rod
Outlet
Disconnect
air hose
1
4
Remove the jammed nail with a slotted screw
driver.
Nail
Slotted Screw Driver
5
Cut the deformed collated wire with nippers.
Correct the deformation.
6
In case of frequent jam, contact a Hitachi
authorized service center.
2. Inspecting the push lever
1
DISCONNECT AIR HOSE.
2
Clean the push lever sliding part.
Lubricate it with Hitachi pneumatic tool lubricant.
Lubricate
Disconnect
air hose
1
3. Inspecting the feeders
1
DISCONNECT AIR HOSE.
2
Clean the knob sliding part.
Lubricate it with Hitachi pneumatic tool lubricant.
Nail
Guide
Knob
Push Lever
Disconnect
air hose
1
3
Open the nail guide and remove dust.
Lubricate the sliding groove of the feeder and
shafts.
Nail Guide
Main Nail Stopper
Feeder
Feeder Shaft
Nose Opening
Sub Nail Stopper
18
English
4
Lubricate the feeding surfaces of the nose and
the nail guide after cleaning.
This promotes smooth operation and prevents
rust.
CAUTION
Check that the main nail stopper and sub nail
stopper slide smoothly by pushing them with
nger.
If not smooth, nails can be driven at an irregular
angle and hurt someone.
4. Inspecting the magazine
1
DISCONNECT AIR HOSE.
2
Clean the magazine. Remove dust or wooden tips
which may have accumulated in the magazine.
5. Storing
When not in use for an extended period, apply a
thin coat of the lubricant to the steel parts to avoid
rust.
Do not store the Nailer in a cold weather
environment.
Keep the Nailer in a warm area.
When not in use, the Nailer should be stored in a
warm and dry place.
Keep out of reach children.
6. WARNING LABEL
Change the WARNING LABEL if missing or
damaged.
A new WARNING LABEL is available from a Hitachi
authorized service center.
Warning
Label
7. Maintenance chart (See page 19)
8. Operator troubleshooting (See page 19)
9. Service parts list
CAUTION
Repair, modi cation and inspection of Hitachi
Power Tools must be carried out by a Hitachi
Authorized Service Center.
This Parts List will be helpful if presented with
the tool to the Hitachi Authorized Service Center
when requesting repair or other maintenance. In
the operation and maintenance of power tools,
the safety regulations and standards prescribed
in each country must be observed.
MODIFICATIONS:
Hitachi Power Tools are constantly being improved
and modi ed to incorporate the latest technological
advancements.
Accordingly, some parts may be changed without prior
notice.
SERVICE AND REPAIRS
WARNING
Only service personnel trained by Hitachi,
distributor or employer shall repair the Nailer.
Use only parts supplied or recommended by
Hitachi for repair.
All quality Nailers will eventually require servicing or
replacement of parts because of wear from normal use.
NOTE: Speci cations are subject to change without any
obligation on the part of HITACHI.
19
English
Maintenance chart
ACTION WHY HOW
Drain air line lter daily. Prevent accumulation of moisture
and dirt.
Open manual petcock.
Keep lubricator lled. Keep the Nailer lubricated. Fill with Hitachi pneumatic tool
lubricant.
Clean lter element — then blow air
through lter in direction opposite to
normal ow.
Prevent clogging of lter with dirt. Follow manufacturers instructions.
Clean magazine and feeder
mechanism.
Prevent a jam. Blow clean daily.
Keep push lever working properly. Promote operator safety and e cient
Nailer operation.
Blow clean daily.
Lubricate the Nailer after nailing. Extend the Nailer life. Supply 5 – 10 drops of lubricant into
the Nailer.
Drain air compressor. Keep the Nailer operated properly. Open petcock on air compressor
tank.
Operator troubleshooting
Most minor problems can be resolved quickly and easily using the table below.
If problems persist, contact a Hitachi authorized service center for assistance.
PROBLEM CHECK METHOD CORRECTION
Nailer operates, but no nail is driven. Check for a jam. Clear a jam.
Check function of nail feeder per
page 17.
Clean and lubricate.
Ribbon spring weakened or
damaged?
Replace ribbon spring.
Check for proper nails. Use only recommended nails.
Weak drive.
Slow to cycle.
Check air pressure. Increase air pressure. (Do not exceed
120 psi (8.3 bar 8.5 kgf/cm
2
).)
Use Hitachi pneumatic tool lubricant.
Driver blade worn? Contact Hitachi for replacement.
Piston O-ring worn or damaged?
Drives too deep. Check air pressure. Reduce air pressure.
(Adjust 70 – 120 psi)
Skipping nails. Intermittent feed. Check for proper nails. Use only recommended nails.
Check function of nail feeder per
page 17.
Clean and lubricate.
Ribbon spring weakened or
damaged?
Replace ribbon spring.
Use Hitachi pneumatic tool lubricant.
Piston O-ring cut or heavily worn? Contact Hitachi for replacement.
Nails jam.
Driven nail is bent.
Check for proper nails. Use only recommended nails.
Driver blade worn? Contact Hitachi for replacement.
Drives properly during normal
operation, but does not drive fully at
faster nailing speeds.
Check inside diameter of air hose. Use larger air hose.
20
Français
INFORMATION IMPORTANTE DE SÉCURITÉ
Lire et bien assimiler toutes les étiquettes de l’outil ainsi que toutes les instructions de fonctionnement,
les consignes de sécurité et les avertissements de ce mode d’emploi avant d’utiliser ou d’entretenir ce
cloueur.
Le non respect des avertissements pourrait entraîner la MORT ou des BLESSURES GRAVES.
La plupart des accidents résultant de l’utilisation ou de l’entretien des cloueurs sont dus au non respect de certaines
consignes et précautions de sécurité élémentaires. Un accident peut souvent être évité en reconnaissant une situation
potentiellement dangereuse avant qu’elle ne se produise, et en respectant les procédures de sécurité applicables.
Les consignes de sécurité élémentaires sont données dans la section “SECURITE” du manuel et dans les sections
relatives aux instructions d’utilisation et dentretien.
Les dangers à éviter pour empêcher tout risque de blessures ou de dommage de loutil sont identi és par les mots
DANGER et AVERTISSEMENT, sur le cloueur et dans ce manuel.
NE JAMAIS utiliser ce cloueur pour des applications autres que celles qui sont spéci ées dans ce manuel.
DEFINITION DES MOTS DE SIGNALISATION
DANGER indique une situation imminente dangereuse qui, si elle n’est pas évitée, entraînera la mort ou des
blessures graves.
AVERTISSEMENT indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, risque d’entraîner
la mort ou des blessures graves.
ATTENTION indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, risque d’entraîner des
blessures léres ou modérées, ou dendommager loutil.
REMARQUE met en relief les informations essentielles.
EXPLICATION DE LACTION DE CLOUAGE DU CLOUEUR HITACHI
MÉCANISME DE DÉCLENCHEMENT SÉQUENTIEL UNIQUE:
Appuyer tout dabord le levier-poussoir contre le bois, puis tirer sur la gâchette pour enfoncer le clou.
Tirer tout d’abord sur la gâchette, puis appuyer le levier-poussoir contre le bois pour enfoncer le clou.
Quand un clou est enfoncé, il n’est plus possible d’enfoncer un autre clou tant que l’on n’a pas relâché la gâchette et
appuyé à nouveau.
MÉCANISME DE DÉCLENCHEMENT PAR CONTACT :
Appuyer tout dabord le levier-poussoir contre le bois, puis tirer sur la gâchette pour enfoncer le clou.
Tirer tout d’abord sur la gâchette, puis appuyer le levier-poussoir contre le bois pour enfoncer le clou.
Si la gâchette est maintenue tirée, un clou s’enfonce chaque fois que lon appuie le levier-poussoir contre le bois.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Hitachi NV 83A3 Instruction And Safety Manual

Catégorie
Cloueuse
Taper
Instruction And Safety Manual

dans d''autres langues