Samsung LN-S2351W Manuel utilisateur

Owner’s

Instructions

This device is a Class B digital apparatus.

Register your product at

www.samsung.com/global/register

LN-S2351W

LN-S2352W

TFT-LCD TELEVISION

BN68-00998G-00

Contact SAMSUNG WORLD-WIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG

customer care center.

Comment contacter Samsung dans le monde

Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez contacter le Service

Consommateurs Samsung.

Contacte con SAMSUNG WORLD-WIDE

Si tiene alguna pregunta o comentario referente a nuestros productos, por favor contacte con nuestro Servicio de

Atención al Cliente.

Country

CANADA

U.S.A

Customer Care Center

1-800-SAMSUNG (7267864)

Address

Samsung Electronics Canada Inc., Customer Service

55 Standish Court Mississauga, Ontario L5R 4B2

Canada

Samsung Electronique Canada Inc., Service

á

la Client

é

le

55 Standish Court Mississauga, Ontario L5R 4B2

Canada

Samsung Electronics America, Inc.

105 Challenger Road

Ridgefield Park, NJ 07660-0511

Web Site

www.samsung.com/ca

www.samsung.com

BN68-00998G-00Cover.qxd 7/3/06 8:31 PM Page 1

Precautions When Displaying a Still Image

A still image may cause permanent damage to the TV screen.

• Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention.

This image retention is also known as "screen burn".

To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

• Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and center of the screen

caused by the difference of light emission on the screen.

Playing a DVD or a game console may cause a similar effect to the screen.

Damages caused by the above effect are not covered by the Warranty.

• Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images.

To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

Précautions à prendre lors de l'affichage d'une image fixe

Une image fixe peut causer des dommages irrémédiables à l'écran du téléviseur.

• N'affichez pas une image fixe sur l'écran LCD plus de 2 heures. Cela pourrait provoquer une rémanence de l'image à l'écran.

Cette rémanence de l'image est également appelée "brûlure de l'écran".

Pour éviter une telle rémanence de l'image à l'écran, réduisez la luminosité et le contraste de l'écran lorsque vous laissez une image fixe affichée.

• Regarder l'écran LCD du téléviseur en format 4:3 pendant une longue période peut laisser des traces de bordures à gauche,

à droite et au centre de l'écran, à cause de la différence d'émission de lumière sur l'écran.

La lecture d'un DVD ou l'utilisation d'une console de jeu peut avoir un effet similaire sur l'écran.

Les dommages provoqués par les effets qui précèdent ne sont pas couverts par la garantie.

• L'affichage d'images fixes de jeux vidéo et d'ordinateurs pendant plus longtemps qu'une période spécifique peut provoquer des rémanences.

Pour éviter cela, réduisez la "luminosité" et le "contraste" lors de l'affichage d'images fixes.

Precauciones al mostrar en la pantalla una imagen fija

La imagen fija puede causar daños permanentes en la pantalla del televisor.

• No deje una imagen fija en la pantalla LCD durante más de dos horas ya que se podría producir una retención de la imagen en la pantalla. Este fenómeno de

retención de imágenes también se denomina "quemadura de pantalla".

Para evitar que se produzca esa persistencia de la imagen, reduzca el nivel de luminosidad y de contraste de la pantalla cuando muestre imágenes fijas.

• El uso del televisor LCD en formato 4:3 durante un tiempo prolongado puede dejar rastros de bordes en las partes izquierda,

derecha y central de la pantalla debido a las diferencias en la emisión lumínica de la pantalla.

La reproducción de un DVD o el uso de una consola de videojuegos pueden provocar un efecto similar en la pantalla.

Reproducir un DVD o una videoconsola puede causar un efecto similar en la pantalla. La garantía no cubre estos daños.

• Ver imágenes fijas de videojuegos y PC durante más tiempo del indicado puede producir restos de imágenes parciales.

Para evitar este efecto, reduzca el 'brillo' y el 'contraste' cuando vea imágenes fijas.

MIJU-Still.qxd 7/3/06 8:31 PM Page 1

English-1

English

Symbol Press Important Note One-Touch

Button

Contents

GENERAL INFORMATION

List of Features .................................................................................. 2

Accessories........................................................................................ 2

Installing the Stand ............................................................................ 2

Installing the Wall Mount Kit ......................................................... 2

Viewing the Control Panel.................................................................. 3

Viewing the Connection Panel ........................................................... 4

Viewing the Remote Control .............................................................. 5

Installing Batteries in the Remote Control ......................................... 6

CONNECTIONS

Connecting VHF and UHF Antennas ................................................. 6

Connecting Cable TV ......................................................................... 7

Connecting a VCR ............................................................................. 8

Connecting an S-VHS VCR ............................................................... 8

Connecting a DVD Player .................................................................. 9

Connecting a DVD Player/Set-Top Box via DVI ................................ 9

Connecting a DVD Player/Set-Top Box via HDMI ............................. 10

Connecting a PC................................................................................ 10

OPERATION

Turning the TV On and Off................................................................. 11

Plug and Play Feature ....................................................................... 11

Changing Channels ........................................................................... 12

Adjusting the Volume ......................................................................... 12

Viewing the Display............................................................................ 12

Selecting the Video Signal-source ..................................................... 13

Storing Channels Automatically ......................................................... 13

Storing Channels Manually ................................................................ 13

PICTURE CONTROL

Using Automatic Picture Settings ...................................................... 14

Customizing the Picture ..................................................................... 14

Adjusting the Color Tone.................................................................... 14

Resetting the Picture Settings to the Factory Defaults...................... 15

Changing the Picture Size ................................................................. 15

Setting the Digital Noise Reduction (Digital NR) ............................... 15

Dynamic Contrast............................................................................... 15

Viewing Picture-in-Picture .................................................................. 16

SOUND CONTROL

Using Automatic Sound Settings .................................................. 16

Customizing the Sound ................................................................ 17

Choosing a Multi-Channel Sound (MTS) Soundtrack .................. 17

Using the Auto Volume ................................................................. 17

Listening to the Sound of the Sub (PIP) Picture .......................... 17

R

esetting the Sound Settings to the Factory defaults .................. 17

TIME SETTING

Setting the Clock .......................................................................... 18

Setting the Sleep Timer ............................................................... 18

Setting the On/Off Timer............................................................... 18

FUNCTION DESCRIPTION

Using the V-Chip........................................................................... 19

Selecting a Menu Language......................................................... 21

U

sing Game mode........................................................................ 21

Viewing Closed Captions ............................................................. 21

Using the Energy Saving Feature ................................................ 22

Setting the Blue Screen Mode...................................................... 22

Selecting the Melody .................................................................... 22

Selecting the Source .................................................................... 22

Editing the Input Source Name .................................................... 22

PC DISPLAY

Setting Up Your PC Software (Based on Windows XP)............... 23

Display Modes .............................................................................. 23

Setting up the TV with your PC .................................................... 24

TROUBLESHOOTING

Identifying Problems ..................................................................... 25

APPENDIX

Specifications ............................................................................... 25

BN68-00998G-00Eng.qxd 7/3/06 8:27 PM Page 1

English-2

List of Features

 Adjustable picture settings that can be stored in the TV’s memory.

 Dynamic Contrast: Automatically detects the input visual signal and adjusts to create optimum contrast.

 Automatic timer to turn the TV on and off.

 A special sleep timer.

 V-Chip function.

Accessories

Installing the Stand

Please make sure the following items are included with your LCD TV. If any items are missing, contact your dealer.

Stand

LN-S2351W : BN96-03358B

LN-S2352W : BN96-03358A

Stand Screw x 4

LN-S2351W : 6003-001294

LN-S2352W : 6003-001324

Owner’s Instructions

Warranty Card / Registration Card

/Safety Guide Manual

(Not available in all locations)

1. Place the TV faced down on a soft cloth or cushion on a table.

2. Put the stand into the hole at the bottom of the TV.

3. Insert screw into the hole indicated and tighten.

Installing the Wall Mount Kit

Wall mount items (sold separately) allow you to mount the TV on the

wall. For detailed information on installing the wall mount, see the

instructions provided with the Wall Mount items.

Contact a technician for assistance when installing the wall mounted

bracket.

Samsung Electronics is not responsible for any damage to the

product or injury to yourself or others if you elect to install the TV on

your own.

Remove the stand and cover the bottom hole with a cap and fasten

with two screws.

< 2 > < 3 >

M4 X L16

General Information

Remote Control & Batteries (AAA x 2)

LN-S2351W : BN59-00545A

LN-S2352W : BN59-00518A

Power Cord

(3903-000144)

Cleaning Cloth

(BN63-01798A)

Cover-Bottom

LN-S2351W : BN63-02323B

LN-S2352W : BN63-02323C

The items color and shape may vary depending on the model.

BN68-00998G-00Eng.qxd 7/3/06 8:27 PM Page 2

English-3

Viewing the Control Panel

SOURCE

Toggles between all the available input sources

(TV, AV1, AV2, S-Video, Component1, Component2, PC, HDMI).

In the on-screen menu, use this button as you use the

ENTER

button on the remote control.

MENU

Press to see an on-screen menu of your TV’s features.

Press to increase or decrease the volume.

In the on-screen menu, use the buttons as you use the

 and  buttons on the remote control.

Press to change channels.

In the on-screen menu, use the buttons as you use the

 and  buttons on the remote control.

SPEAKERS

(POWER)

Press to turn the TV on and off.

POWER INDICATOR

Blinks and turns off when the power is on and lights up in

stand-by mode.

REMOTE CONTROL SENSOR

Aim the remote control towards this spot on the TV.

The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu.

To use the more advanced features, you must use the remote control.

The product color and shape may vary depending on the model.

BN68-00998G-00Eng.qxd 7/3/06 8:27 PM Page 3

English-4

Viewing the Connection Panel

HDMI/DVI IN, DVI IN

Connect to the HDMI jack of a device with an HDMI output. Use the HDMI/DVI terminal for DVI connection to an external device.

You should use the DVI to HDMI cable or DVI-HDMI adapter (DVI to HDMI) for video connection, and the DVI-IN ‘R-AUDIO-L’ terminal for audio.

HDMI/DVI IN terminal does not support PC.

No sound connection is needed for an HDMI to HDMI connection.

PC IN

Connect to the video and audio output jack on your PC.

ANT IN

Connect to an antenna or to a cable TV system.

HEADPHONE

Connect a set of external headphones for private listening.

AV IN

Video and audio inputs for external devices, such as a camcorder or VCR.

S-VIDEO

Connect an S-Video signal from a camcorder or VCR.

POWER INPUT

Connect the supplied power cord.

COMPONENT IN 1, 2

Connect component video/audio.

KENSINGTON LOCK

The Kensington lock (optional) is a device used to physically fix the system when used in a public place.

If you want to use a locking device, contact the dealer where you purchased the TV.

Use the rear panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players.

For more information on connecting equipment, see pages 6-10.

BN68-00998G-00Eng.qxd 7/3/06 8:27 PM Page 4

English-5

Turns the TV on and off.

Press to select channels directly on the TV.

Press to select additional channels (digital and analog) being broadcast by the same

station. For example, to select channel “54-3”, press “54”, then press “

–

” and “3”.

Press to increase or decrease the volume.

Press to temporarily cut off the sound.

Displays the main on-screen menu.

Use to select on-screen menu items and change menu values.

Adjust the TV sound by selecting one of the preset factory settings.

(or selects your personal, customized sound settings)

Adjust the TV picture by selecting one of the preset factory settings.

(or selects your personal, customized picture settings)

Press to select a time for the TV to turn off automatically.

Press to choose stereo, mono or Separate Audio Program (SAPbroadcast).

Press to automatically store selected TV/Cable channels.

Use to store and delete channels to/from memory.

Press to display information on the TV screen.

Input source selection

Returns to the previous channel.

Press

CH

/

buttons to change channels.

Press to exit the on-screen menu.

Press to stop the action during a particular scene. Press again to resume normal video.

Press to change the screen size.

Picture-in-Picture ON/OFF.

Displays the available channels in sequence. (These buttons change channels in the

PIP window only.)

Press to set caption on/off.

The performance of the remote control may be affected by bright light.

Viewing the Remote Control

BN68-00998G-00Eng.qxd 7/3/06 8:27 PM Page 5

English-6

1. Lift the cover at the back of the remote control upward as shown in the figure.

2. Install two AAA size batteries.

Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment.

3. Replace the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time.

The remote control can be used up to about 23 feet from the TV.

(Assuming typical TV usage, the batteries last for about one year.)

If the remote control doesn’t work, check the following:

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage, or is the power cord unplugged?

5. Is there a special fluorescent light or neon sign nearby?

Installing Batteries in the Remote Control

1. Place the wires from the twin leads under the screws on a 300-75

Ω

adapter

(not supplied).

Use a screwdriver to tighten the screws.

2. Plug the adaptor into the ANT IN terminal on the back of the TV.

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like this, see “Antennas with 300

Ω

Flat Twin Leads” below.

If your antenna has one lead that looks like this, see “Antennas with 75

Ω

Round Leads”.

If you have two antennas, see “Separate VHF and UHF Antennas”.

Antennas with 300 Ω Flat T

win Leads

If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300

Ω

twin flat leads, follow the directions below.

1. Plug the antenna lead into the ANT IN terminal on the back of the TV.

Antennas with 75 Ω Round Leads

1. Connect both antenna leads to the combiner.

2. Plug the combiner into the ANT IN terminal on the bottom of the rear panel.

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the

TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

UHF

VHF

ANT IN

UHF

VHF

Connections

BN68-00998G-00Eng.qxd 7/3/06 8:27 PM Page 6

English-7

After you have made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled channels.

(When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)

2. Connect this cable to a two-way splitter.

Splitter

Incoming

cable

3. Connect an RF cable between an OUTPUT

terminal on the splitter and the IN terminal on the

cable box.

Splitter

Cable Box

Incoming

cable

4. Connect an RF cable between the ANT OUT

terminal on the cable box and the B–IN terminal

on the RF(A/B) switch.

Splitter

Cable Box

RF (A/B)

Switch

Incoming

cable

5. Connect another cable between the other OUT

terminal on the splitter and the A–IN terminal on

the RF (A/B) switch.

Splitter

Cable Box

Incoming

cable

6. Connect the last RF cable between the OUT

terminal on the RF (A/B) switch and the ANT IN

terminal on the rear of the TV.

Splitter

Cable Box

Incoming

cable

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way splitter, an RF (A/B)

switch, and four lengths of RF cable. (These items are available at most electronics stores.)

1. Find and disconnect the cable that is

connected to the ANT IN terminal on your

cable box.

This terminal might be labeled “ANT IN”, “VHF IN” or

simply, “IN”.

ANT IN

RF (A/B)

Switch

TV Rear

RF (A/B)

Switch

ANT IN

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

1. Plug the incoming cable into the ANT IN terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.

2. Connect the other end of this cable to the ANT IN terminal on the back of the TV.

Connecting to a Cable Box that Descrambles All Channels

1. Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.

ANT OUT

ANT IN

BN68-00998G-00Eng.qxd 7/3/06 8:27 PM Page 7

English-8

Connecting a VCR

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on

pages 6-7). Skip step 1 if you have not yet connected to an antenna or a cable system.

1. Unplug the cable or antenna

from the back of the TV.

2. Connect the cable or antenna to

the ANT IN terminal on the back

of the VCR.

3. Connect an RF Cable between

the ANT OUT terminal on the

VCR and the ANT IN terminal on

the TV.

4.

Connect a Video Cable between the

VIDEO OUT jack on the VCR and

the AV IN [VIDEO] jack on the TV.

5.

Connect Audio Cables between

the AUDIO OUT jacks on the

VCR and the AV IN [R-AUDIO-L]

jacks on the TV.

If you have a “mono” (non-stereo)

VCR, use a Y-connector

(not supplied) to hook up to the

right and left audio input jacks of

the TV. If your VCR is stereo,

you must connect two cables.

Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.

Each external input source device has a different back panel configuration.

When connecting an external device, match the color of the connection terminal to the cable.

VCR Rear Panel

TV Rear Panel

RF Cable (Not supplied)

Video Cable (Not supplied)

Audio Cable (Not supplied)

2

3

4

5

Connecting an S-VHS VCR

Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR.

(This connection delivers a better picture as compared to a standard VHS VCR.)

1. To begin, follow steps 1–3 in the

previous section to connect the

antenna or cable to your VCR

and your TV.

2. Connect an S-Video Cable

between the S-VIDEO OUT jack

on the VCR and the

AV IN [S-VIDEO] jack on the TV.

3.

Connect Audio Cables between

the AUDIO OUT jacks on the

VCR and the AV IN [R-AUDIO-L]

jacks on the TV.

An S-Video cable is usually included with an S-VHS VCR. (If not, check your local electronics store.)

Each external input source device has a different back panel configuration.

When connecting an external device, match the color of the connection terminal to the cable.

VCR Rear Panel

TV Rear Panel

RF Cable (Not supplied)

S-Video Cable (Not supplied)

Audio Cable (Not supplied)

3

2

1

ANT IN

BN68-00998G-00Eng.qxd 7/3/06 8:27 PM Page 8

English-9

Connecting a DVD Player/Set-Top Box via DVI

This connection can only be made if there is a DVI Output connector on the external device.

1. Connect a DVI to HDMI Cable

or DVI-HDMI Adapter between

the HDMI/DVI IN connector on

the TV and the DVI connector

on the DVD player/Set-Top Box.

2. Connect Audio Cables between

the DVI IN [R-AUDIO-L] jack on

the TV and the AUDIO OUT

jacks on the DVD player/

Set-Top Box.

DVD Player / Set-Top Box

TV Rear Panel

Audio Cable (Not supplied)

2

Each external input source device has a different back panel configuration.

When connecting an external device, match the color of the connection terminal to the cable.

DVI to HDMI Cable (Not supplied)

1

Connecting a DVD Player

The rear panel jacks on your TV make it easy to connect a DVD player to your TV.

1. Connect a Component Cable

between the COMPONENT IN 1

or COMPONENT IN 2 [P

R, PB, Y]

jacks on the TV and the

COMPONENT [Y, P

B, PR] jacks

on the DVD player.

2. Connect Audio Cables

between the COMPONENT IN 1

or COMPONENT IN 2

[R-AUDIO-L] jacks on the TV and

the AUDIO OUT jacks on the

DVD player.

DVD Player Rear Panel

TV Rear Panel

Component Cable (Not supplied)

Audio Cable (Not supplied)

Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr (Red)

for enhanced video quality.

Be sure to match the component video and audio connections.

For example, if connecting the video cable to COMPONENT IN,

connect the audio cable to COMPONENT IN also.

Each external input source device has a different back panel configuration.

When connecting an external device, match the color of the connection terminal to the cable.

1

2

BN68-00998G-00Eng.qxd 7/3/06 8:27 PM Page 9

English-10

Connecting a DVD Player/Set-Top Box via HDMI

This connection can only be made if there is an HDMI Output connector on the external device.

1. Connect an HDMI Cable

between the HDMI/DVI

connector on the TV and the

HDMI connector on the

DVD player/Set-Top Box.

DVD Player Rear Panel

TV Rear Panel

HDMI Cable (Not supplied)

What is HDMI?

• HDMI, or high-definition multimedia interface, is a next-generation interface that enables the

transmission of digital audio and video signals using a single cable without compression.

• “Multimedia interface” is a more accurate name for it especially because it allows multiple channels of

digital audio (5.1 channels).

The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP

(High Bandwidth Digital Copy Protection) coding feature installed, and supports multi-channel

digital audio.

Each external input source device has a different back panel configuration.

When connecting an external device, match the color of the connection terminal to the cabl

e.

Connecting a PC

1. Connect a D-Sub Cable

between PC IN [PC]

connector on the TV and the

PC output connector on your

computer.

2. Connect a PC Audio Cable

between PC IN [AUDIO] jack on

the TV and the Audio Out jack

of the sound card on your

computer.

PC

TV Rear Panel

D-Sub Cable (Not supplied)

PC Audio Cable (Not supplied)

Each external input source device has a different back panel configuration.

When connecting an external device, match the color of the connection terminal to the cable.

The HDMI/DVI jacks do not support PC connection.

1

2

BN68-00998G-00Eng.qxd 7/3/06 8:27 PM Page 10

English-11

Turning the TV On and Off

Press the POWER button on the remote control.

You can also use the

POWER button on the front of the panel.

Plug and Play Feature

When the TV is initially powered on, several basic settings proceed automatically and subsequently.

The following settings are available.

1. Press the POWER button on the remote control.

The message “Plug & Play” is displayed.

2. Select the appropriate language by pressing the  or  button.

Press the

ENTER button to confirm your choice.

3. The message “Check antenna input.” is displayed with “OK” selected.

Press the

ENTER button.

Please check that the antenna cable is connected correctly.

4. Press the  or  button to select “Air”, “STD”, “HRC”, or “IRC”, then press the ENTER button.

5. Press the ENTER button to select “Start”.

The channel search will start and end automatically.

After all the available channels are stored, the “Clock Set” menu appears.

Press the ENTER button at any time to interrupt the memorization process.

6. Press the ENTER button.

Press the

 or  button to move to the “Hour”, “Minute” or “am/pm”.

Set the “Hour”, “Minute” or “am/pm” by pressing the

 or  button.

7. Press the ENTER button to confirm your setting.

The message “Enjoy your watching.” is displayed.

If you want to reset this feature...

1. Press the MENU button to display the menu.

Press the

 or  button to select “Setup”, then press the ENTER button.

2. Press the ENTER button to select “Plug & Play”.

3. This will change or reset the settings.

• Language: Select your language.

• Air/Cable: Select your local cable company TV system.

• Auto Program: Selects between terrestrial antenna connection or your local cable company TV system.

The TV automatically cycles through all of the available channels and stores them

in memory. This takes about one to two minutes.

• Clock Set: Sets the current time for the TV clock.

You can also set the hour and minute by pressing the number buttons on the remote control.

Operation

BN68-00998G-00Eng.qxd 7/3/06 8:28 PM Page 11

English-12

Viewing the Display

Press the button once more or wait approximately 10 seconds and it disappears automatically.

Press the INFO button on the remote control to view current channel and the status of certain

audio-video settings.

Adjusting the Volume

1.

Press the VOL or VOL button to increase or decrease the volume.

Using MUTE button:

At any time, you can temporarily cut off the sound using the MUTE button.

1.

Press MUTE and the sound cuts off. The word “Mute” will appear in the lower-left corner of the screen.

2.

To turn mute off, press the MUTE button again, or simply press the VOL or VOL button.

Changing Channels

Using the Channel Buttons:

1. Press the CH or CH button to change channels.

When you press the CH or CH button, the TV changes channels in sequence.

You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels).

You will not see channels that were either erased or not memorized.

Using the PRE-CH Button to select the Previous Channel:

1. Press the PRE-CH button. The TV will switch to the last channel viewed.

To quickly switch between two channels that are far apart, tune to one channel, then use the number button

to select the second channel. Then use the PRE-CH button to quickly alternate between them.

BN68-00998G-00Eng.qxd 7/3/06 8:28 PM Page 12

English-13

Storing Channels Manually

You can store up to 100 channels, including those received via cable networks.

1. Press the MENU button to display the menu.

Press the

 or  button to select “Channel”, then press the ENTER button.

2. Press the  or  button to select “Add/Delete”.

Press the

ENTER button.

3. Repeatedly pressing the ENTER button will alternate between add channel and delete channel.

4. Press the CH or CH button to switch to the appropriate channel, then repeat above.

5. Press the EXIT button to exit.

You can view any channel (including an erased channel) by using the number buttons on the remote control.

Use the number buttons to directly select the channel that will be added or erased.

Press the

ADD/DEL button on the remote control.

Storing Channels Automatically

The TV automatically cycles through all of the available channels and stores them in memory.

This takes about one to two minutes.

1. To select the signal source, follow the “Selecting the Video Signal-source” instructions

number 1 to 3 on page 13.

2. Press the  or  button to select “Auto Program”. Press the ENTER button.

3. Press the ENTER button. The channel search will start and end automatically.

Press the ENTER button at any time to interrupt the memorization process and return to the “Channel” menu.

4. After all the available channels are stored, the “Channel” menu reappears.

5. Press the EXIT button to exit.

Press the AUTO PROG. button on the remote control.

Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must specify the type of signal

source that is connected to the TV (i.e. an antenna or a cable system).

1. Press the MENU button to display the menu.

Press the

 or  button to select “Channel”, then press the ENTER button.

2. Press the ENTER button to select “Air/Cable”.

3. Press the  or  button to select the video signal source, then press the ENTER button.

4. Press the EXIT button to exit.

STD, HRC and IRC identify various types of cable TV systems.

Contact your local cable company to identify the type of cable system that exists in your particular area.

At this point, the signal source has been selected. Proceed to “Storing Channels Automatically”.

BN68-00998G-00Eng.qxd 7/3/06 8:28 PM Page 13

Using Automatic Picture Settings

Your TV has four automatic picture settings (“Dynamic”, “Standard”, “Movie”, “Custom”) that are preset

at the factory. Each Picture mode can be set to your preference by adjusting particular items such as

Contrast, Brightness, Sharpness, Color, Tint and Color Tone.

1. Press the MENU button to display the menu.

Press the

 or  button to select “Picture”, then press the ENTER button.

2. Press the ENTER button, to select “Mode”.

3. Press the ENTER button again, to select “Mode”.

4. Press the  or  button to select the desired picture effect.

Press the

ENTER button.

5. Press the EXIT button to exit.

• Cool2: Makes the color temperature bluer than “Cool1” menu.

• Cool1: Makes whites bluish.

• Normal: Keeps whites white.

• Warm1: Makes whites reddish.

• Warm2: Makes the color temperature redder than “Warm1” menu.

Adjusting the Color Tone

You can Change the color of the entire screen according to your preference.

1. To select the desired picture effect, follow the “Using Automatic Picture Settings ” instructions

number 1 to 4 on page 14.

2. Press the  or  button to select “Color Tone”, then press the ENTER button.

3.

Press the

 or  button

to select the desired color tone setting.

Press the

ENTER

button.

4.

Press the EXIT button to exit.

Customizing the Picture

Your set has several settings which allow you to control picture quality.

1. To select the desired picture effect, follow the “Using Automatic Picture Settings ” instructions

number 1 to 4 on page 14.

2. Press the  or  button to select a particular item.

Press the

ENTER button.

3. Press the  o  button to decrease or increase the value of a particular item.

Press the

ENTER button.

4. Press the EXIT button to exit.

The adjusted values are stored according to the selected Picture mode.

• Dynamic: Selects the picture for high-definition in a bright room.

• Standard: Selects the picture for optimum display in a normal environment.

• Movie: Selects the picture for comfortable display in a dark room.

• Custom: Select to view your favorite display settings (see “Customizing the Picture”, page 14).

You can also press the P.MODE button on the remote control to select one of the picture settings.

The Picture mode must be adjusted separately for each input source.

You can return to the factory defaults picture settings by selecting the “Reset”.

(see “Resetting the Picture Settings to the Factory Defaults”, page 15).

•

Contrast: Adjusts the lightness and darkness between objects and the background.

•

Brightness: Adjusts the brightness of the whole screen.

•

Sharpness:

Adjusts the outline of objects to either sharpen them or make them more dull.

•

Color: Adjusts the colors, making them lighter or darker.

•

Tint:

Adjusts the color of objects, making them more red or green for a more natural look.

English-14

Picture Control

BN68-00998G-00Eng.qxd 7/3/06 8:28 PM Page 14

English-15

Dynamic Contrast

Dynamic Contrast is to automatically detect distribution of inputted visual signal and adjust to create

optimum contrast.

1. Press the MENU button to display the menu.

Press the

 or  button to select “Picture”, then press the ENTER button.

2. Press the  or  button to select “Dynamic Contrast”, then press the ENTER button.

3. Press the  or  button to select “On” or “Off”.

Press the

ENTER button.

4. Press the EXIT button to exit.

This function don’t work in PC mode.

Changing the Picture Size

You can select the picture size which best corresponds to your viewing requirements.

1. Press the MENU button to display the menu.

Press the

 or  button to select “Picture”, then press the ENTER button.

2. Press the  or  button to select “Size”, then press the ENTER button.

3. Select the required option by pressing the  or  button.

Press the

ENTER button.

4. Press the EXIT button to exit.

In PC, Component and DVI Mode, only “16:9” and “4:3” mode can be adjusted.

(

The “Zoom” mode is not supported.)

Select by pressing the  or  buttons.

Use the  or  button to move the picture up and down.

After selecting , use the  or  button to magnify or reduce the picture size in the vertical direction.

• 16:9: Adjusts the picture size to 16:9 appropriate for DVDs or wide broadcasting.

• Zoom: Magnifies the 16:9 wide picture (in the vertical direction) to fit the screen size.

• 4:3: This is the default setting for a video movie or normal broadcasting.

Resetting the Picture Settings to the Factory Defaults

You can return to the factory defaults picture settings.

1. To select the desired picture effect, follow the

“Using Automatic Picture Settings ” instructions number 1 to 4 on page 14.

2. Press the  or  button to select “Reset”, then press the ENTER button.

3. Press the EXIT button to exit.

The “Reset” will be set for each picture mode.

Setting the Digital Noise Reduction (Digital NR)

If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature

to help reduce any static and ghosting that may appear on the screen.

1. Press the MENU button to display the menu.

Press the

 or  button to select “Picture”, then press the ENTER button.

2. Press the  or  button to select “Digital NR”, then press the ENTER button.

3. Press the  or  button to select “On” or “Off”.

Press the

ENTER button.

4. Press the EXIT button to exit.

This function don’t work in PC mode.

BN68-00998G-00Eng.qxd 7/3/06 8:28 PM Page 15

English-16

When the main picture is PC, the sub picture only supports TV, AV and S-VIDEO.

The sub picture does not support other input sources in this case.

You may notice that the picture in the PIP window becomes slightly unnatural when you use the main screen

to view a game or karaoke.

While V-Chip is in operation, the PIP function cannot be used.

Viewing Picture-in-Picture

This product has one built-in tuner, which does not allow PIP to function in the same mode. For example,

you cannot watch one TV channel in the main screen, and a different one in the PIP screen. You can use the

PIP feature to simultaneously watch two video sources.

1. Press the MENU button to display the menu.

Press the

 or  button to select “Picture”, then press the ENTER button.

2. Press the  or  button to select “PIP”, then press the ENTER button.

3. Press the ENTER button.

4. Press the  or  button to select “On”

Press the

ENTER button.

PIP is available only in PC mode and will be unavailable for other modes.

If you turn the TV off while watching in PIP mode and turn it on again, the PIP window will disappear.

5. Press the  or  button to select “Source”, then press the ENTER button.

6. Select the source of the sub picture (PIP) by pressing the  or  buttons and

press the

ENTER button.

7. Press the  or  button to select “Position”, then press the ENTER button.

8. Press the  or  buttons to select the desired PIP window position.

Press the

ENTER button.

9. Press the  or  button to select “Channel”, then press the ENTER button.

10. Press the  or  buttons to select the desired channel in the PIP window.

Press the

ENTER button.

11. Press the EXIT button to exit.

• Source: Selecting a signal source (external A/V) for PIP.

The sub picture can serve different source selections based on what the main picture is set to.

• Position: Changing the position of the PIP window.

• Channel: Changing the PIP channel.

The channel can be active when the sub picture is set to TV.

PIP Settings

(O: PIP operates, X: PIP doesn’t operate)

PC

TV

O

AV1

O

AV2

O

S-Video

O

Component1

X

Component2

X

PC

X

HDMI

X

Sub

Main

Press the PIP button on the remote control repeatedly to activate or deactivate the “PIP”.

Using Automatic Sound Settings

You can select the type of the special sound effect to be used when watching a given broadcast.

1. Press the MENU button to display the menu.

Press the

 or  button to select “Sound”, then press the ENTER button.

2. Press the ENTER button to select “Mode”.

3. Press the  or  button to select the desired sound effect.

Press the

ENTER button.

4. Press the EXIT button to exit.

You can also press the S.MODE button on the remote control to select one of the sound settings.

• Standard: Selects the normal sound mode.

• Music: Emphasizes music over voices.

• Movie: Provides live and full sound for movies.

• Speech: Emphasizes voices over other sounds.

• Custom: Selects your custom sound settings (See “Customizing the Sound”, page 17).

Sound Control

BN68-00998G-00Eng.qxd 7/3/06 8:28 PM Page 16

English-17

• Mono: Select for channels that are broadcast in mono, or if you are having difficulty receiving a stereo signal.

• Stereo: Select for channels that are broadcast in stereo.

• SAP: Select to listen to the Separate Audio Program, which is usually a foreign-language translation.

Choosing a Multi-Channel Sound (MTS) Soundtrack

Depending on the particular program being broadcast, you can listen to stereo, mono or a Separate

Audio Program. (SAP audio is usually a foreign-language translation. Sometimes SAP has unrelated

information like news or weather).

1. Press the MENU button to display the menu.

Press the

 or  button to select “Sound”, then press the ENTER button.

2. Press the  or  button to select “MTS”, then press the ENTER button.

3. Press the  or  button to select the required option, then press the ENTER button.

4. Press the EXIT button to exit.

You can also press the MTS button on the remote control to change the MTS settings.

Using the Auto Volume

Each broadcasting station has its own signal conditions, and it is inconvenient to adjust the volume every

time the channel is changed.

“Auto Volume” automatically adjusts the volume of the desired channel by lowering the sound output

when the modulation signal is high or by raising the sound output when the modulation signal is low.

1. Press the MENU button to display the menu.

Press the

 or  button to select “Sound”, then press the ENTER button.

2. Press the  or  button to select “Auto Volume”, then press the ENTER button.

3. Press the  or  button to select “On” or “Off”. Press the ENTER button.

4. Press the EXIT button to exit.

Listening to the Sound of the Sub (PIP) Picture

During the PIP feature is activating, you can listen to the sound of the sub picture.

1. Press the MENU button to display the menu.

Press the

 or  button to select “Sound”, then press the ENTER button.

2. Press the  or  button to select “Sound Select”, then press the ENTER button.

3. Press the  or  button to select “Sub”. Press the ENTER button.

4. Press the EXIT button to exit.

Customizing the Sound

The sound settings can be adjusted to suit your personal preferences.

(Alternatively, you can use one of the “automatic” settings.)

1. Press the MENU button to display the menu.

Press the

 or  button to select “Sound”, then press the ENTER button.

2. Press the  or  button to select “Equalizer”, then press the ENTER button.

3. Press the  or  buttons to select a particular frequency to adjust.

Press the

 or  buttons to increase or decrease the level of the particular frequency.

Press the

ENTER button.

4. Press the EXIT button to exit.

If you make any changes to the “Equalizer” settings, the sound mode is automatically switched to the “Custom” mode.

You can select this option when the “PIP” is set to “On”.

•

Main: Used to listen to the sound of the main picture.

•

Sub: Used to listen to the sound of the sub picture.

Resetting the Sound Settings to the Factory defaults

If Game Mode is On, the Reset Sound function is activated. Selecting the Reset function after setting the

equalizer resets the equalizer setting to the factory defaults.

1. Press the MENU button to display the menu.

Press the

 or  button to select “Sound”, then press the ENTER button.

2. Press the  or  button to select “Reset”, then press the ENTER button.

3. Press the EXIT button to exit.

You can select this option when the “Game Mode” is set to “On”.

BN68-00998G-00Eng.qxd 7/3/06 8:28 PM Page 17

Setting the Clock

You can set the TV’s clock so that the current time is displayed when you press the INFO button.

You must also set the time if you wish to use the automatic On/Off timers.

1. Press the MENU button to display the menu.

Press the

 or  button to select “Setup”, then press the ENTER button.

2. Press the  or  button to select “Time”, then press the ENTER button.

3. Press the ENTER button to select “Clock Set”.

4. Press the  or  button to adjust “Hour”, then press the  button to move to the next step.

Set other items using the same method as above.

When finished, press the

ENTER button to return.

5. Press the EXIT button to exit.

If you disconnect the power cord, you have to set the clock again.

You can also set the hour and minute by pressing the number buttons on the remote control.

Setting the Sleep Timer

Setting the On/Off Timer

Set the timer for the TV to turn off at the preset time automatically.

1. Press the MENU button to display the menu.

Press the

 or  button to select “Setup”, then press the ENTER button.

2. Press the  or  button to select “Time”, then press the ENTER button.

3. Press the  or  button to select “Sleep Timer”, then press the ENTER button.

4. Press the  or  button repeatedly until the desired time appears. (Off, 30, 60, 90, 120, 150, 180)

Press the

ENTER

button.

5. Press the EXIT button to exit.

The TV automatically turn off when the timer reaches 0.

You can also press the SLEEP button on the remote control to set the sleep time.

You can set the On/Off timers so that the set will:

Switch on automatically and tune to the channel of your choice at the time you select.

Switch off automatically at the time you select.

1. Press the MENU button to display the menu.

Press the

 or  button to select “Setup”, then press the ENTER button.

2. Press the  or  button to select “Time”, then press the ENTER button.

3. Press the  or  button to select “On Timer”, then press the ENTER button.

4. Press the  or  button to adjust “Hour”, then press the  button to move to the next step.

Set other items using the same method as above.

When finished, press the

ENTER button to return.

5. Press the  or  button to select “Off Timer”, then press the ENTER button.

6. Press the  or  button to adjust “Hour”, then press the  button to move to the next step.

Set other items using the same method as above.

When finished, press the

ENTER button to return.

7. Press the EXIT button to exit.

The clock must be set (see above) before you can set the On/Off timer.

You can also set the hour and minute by pressing the number buttons on the remote control.

The "Activation" setting must be set to "Yes" in order for the timers to work.

Auto Power Off: When you set the timer on, your television will be turned off if you do not operate any

controls for 3 hours after the TV has been turned on with the “Timer On” function.

English-18

Time Setting

BN68-00998G-00Eng.qxd 7/3/06 8:28 PM Page 18

La page charge ...

Samsung LN-S2351W Manuel utilisateur

Samsung LN-S2351W Manuel utilisateur

dans d''autres langues

Documents connexes