Samsung ME17H703SHB/AC Guide d'installation

Installation Instructions

Over The Range Microwave Oven

BEFORE YOU BEGIN (Read these instructions completely and carefully.)

IMPORTANT

Save these instructions for local inspector’s use.

IMPORTANT

Observe all governing codes and ordinances.

• Note to Installer - Be sure to leave these instructions with the Consumer.

• Note to Consumer - Keep these instructions for future reference.

• Skill level - Installation of this appliance requires basic mechanical and electrical skills.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

OTR_II_DE68-03587B-05_EN.indd 1 6/19/2019 3:55:58 PM

2

Contents

Step-by-step installation guideGeneral information

Important safety instructions . . . . . . . 3

Electrical requirements. . . . . . . . . . . 3

Hood exhaust . . . . . . . . . . . . . . . . 4

Damage - Shipment/Installation . . . . . . 6

Parts included. . . . . . . . . . . . . . . . 6

Tools you will need . . . . . . . . . . . . . 7

Mounting space. . . . . . . . . . . . . . . 7

1. Placement of the mounting plate . . . . 8

A. Removing the microwave oven from the

carton/Removing the mounting plate . . 8

B. Finding the wall studs. . . . . . . . . . . 8

C. Determining wall plate location under your

cabinet. . . . . . . . . . . . . . . . . . . 9

D. Aligning the wall plate. . . . . . . . . . 10

2. Installation types (choose A, B or C) . . 11

A. Outside top exhaust (vertical duct). . . 12

A1. Attach the mounting plate to the wall 12

A2. Use top cabinet template for preparation

of top cabinet . . . . . . . . . . . . 12

A3. Installation procedure for exhaust

adaptor and proper damper operation

check . . . . . . . . . . . . . . . . 13

A4. Mount the microwave oven . . . . 13

A5. Adjust the exhaust adaptor . . . . 14

A6. Connecting ductwork. . . . . . . . 14

B. Recirculating (non-vented ductless) . . 15

B1. Attach the mounting plate to the wall 15

B2. Use top cabinet template for preparation

of top cabinet . . . . . . . . . . . . 15

B3. Adapting microwave blower for

recirculation. . . . . . . . . . . . . 16

B4. Mount the microwave oven . . . . 17

B5. Installing the charcoal ﬁlter . . . . 18

C. Outside back exhaust (horizontal duct) 19

C1. Preparing the rear wall for outside back

exhaust . . . . . . . . . . . . . . . 19

C2. Attach the mounting plate to the wall 20

C3. Use top cabinet template for preparation

of top cabinet . . . . . . . . . . . . 20

C4. Adapting microwave blower for outside

back exhaust . . . . . . . . . . . . 20

C5. Mount the microwave oven . . . . 22

Before you use your microwave . . . . . 23

OTR_II_DE68-03587B-05_EN.indd 2 6/19/2019 3:55:59 PM

3

General information

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded outlet.

The installer must perform a ground continuity

check on the power outlet box before beginning the

installation to insure that the outlet box is properly

grounded. If not properly grounded, or if the outlet

box does not meet electrical requirements noted

(under ELECTRICAL REQUIREMENTS), a qualiﬁed

electrician should be employed to correct any

deﬁciencies.

Insure proper

ground exists

before use

CAUTION: For personal

safety, remove house

fuse or open circuit

breaker before

beginning installation

to avoid severe or fatal

shock injury.

CAUTION: For personal safety, the mounting

surface must be capable of supporting the

cabinet load, in addition to the added weight of

this 63–85 pound product, plus additional oven

loads of up to 50 pounds or a total weight of

113–135 pounds.

CAUTION: For personal safety, this product cannot

be installed in cabinet arrangements such as an

island or a peninsula. It must be mounted to BOTH

a top cabinet AND a wall.

NOTE: For easier installation and personal safety,

it is recommended that two people install this

product.

IMPORTANT – PLEASE READ CAREFULLY. FOR

PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED TO AVOID SEVERE OR

FATAL SHOCK.

Insure proper

ground exists

before use

Insure proper

ground exists

before use.

The power cord of this

appliance is equipped

with a three-prong

(grounding) plug which

mates with a standard

three-prong (grounding)

wall receptacle to

minimize the possibility

of electric shock hazard

from this appliance.

You should have the wall receptacle and circuit

checked by a qualiﬁed electrician to make sure

the receptacle is properly grounded.

Where a standard two-prong wall receptacle

is encountered, it is very important to have

it replaced with a properly grounded three-

prong wall receptacle, installed by a qualiﬁed

electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT,

DEFORM OR REMOVE ANY OF THE PRONGS

FROM THE POWER CORD. DO NOT USE WITH

AN EXTENSION CORD.

ELECTRICAL

REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz,

13amps and 1.5 kilowatts. This product must be

connected to a supply circuit of the proper voltage

and frequency. Wire size must conform to the

requirements of the National Electrical Code or the

prevailing local code for this kilowatt rating. The

power supply cord and plug should be brought to a

separate branch circuit single grounded outlet of at

least 15 A and max of 20 A. The outlet box should

be located in the cabinet above the microwave oven.

The outlet box and supply circuit should be installed

by a qualiﬁed electrician and conform to the National

Electrical Code or the prevailing local code.

OTR_II_DE68-03587B-05_EN.indd 3 6/19/2019 3:55:59 PM

4

General information

NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to

recirculate the air back into the room, proceed to page 11.

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)

The following chart contains an example of one possible ductwork installation.

DUCT PIECES

EQUIVALENT

LENGTH

x

NUMBER

USED

=

EQUIVALENT

LENGTH

Roof Cap 24 ft. x (1) = 24 ft.

12 Ft. Straight Duct

(6

˝

Round)

12 ft. x (1) = 12 ft.

Rectangular-to-

Round Transition

Adaptor*

5 ft. x (1) = 5 ft.

Equivalent lengths of duct pieces are based on actual tests

and reﬂect requirements for good venting performance with

any vent hood.

Total Length = 41 ft.

* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be

cut to ﬁt, using the tin snips, in order to allow free movement of the damper.

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

The following chart contains an example of one possible ductwork installation.

DUCT PIECES

EQUIVALENT

LENGTH

x

NUMBER

USED

=

EQUIVALENT

LENGTH

Wall Cap 40 ft. x (1) = 40 ft.

3 Ft. Straight Duct (3¼˝

x 10˝ Rectangular)

3 ft. x (1) = 3 ft.

90° Elbow 10 ft. x (2) = 20 ft.

Equivalent lengths of duct pieces are based on actual tests

and reﬂect requirements for good venting performance with

any vent hood.

Total Length = 63 ft.

NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared

at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.

HOOD EXHAUST

OTR_II_DE68-03587B-05_EN.indd 4 6/19/2019 3:55:59 PM

5

General information

NOTE: If you need to install ducts, note that the total

duct length of 3¼˝ x 10˝ rectangular or 6˝ diameter

round duct should not exceed 140 equivalent feet.

Outside ventilation requires a HOOD EXHAUST DUCT.

Read the following carefully.

NOTE: It is important that venting be installed using

the most direct route and with as few elbows as

possible. This ensures clear venting of exhaust and

helps prevent blockages. Also, make sure dampers

swing freely and nothing is blocking the ducts.

Exhaust connection:

The hood exhaust has been designed to mate with a

standard 3¼˝ x 10˝ rectangular duct.

If a round duct is required, a rectangular-to-round

transition adaptor must be used. Do not use less

than a 6˝ diameter duct.

Maximum duct length:

For satisfactory air movement, the total duct length of

3¼˝ x 10˝ rectangular or 6˝ diameter round duct should

not exceed 140 equivalent feet.

Elbows, transitions, wall and roof

caps, etc., present additional resistance to airﬂow

and are equivalent to a section of straight duct which is

longer than their actual physical size. When calculating

the total duct length, add the equivalent lengths of all

transitions and adaptors plus the length of all straight

duct sections. The chart below shows you how to

calculate total equivalent ductwork length using the

equivalent length in feet of some typical ducts.

DUCT PIECES

EQUIVALENT

LENGTH

x

NUMBER

USED

=

EQUIVALENT

LENGTH

Rectangular-to-Round

Transition Adaptor*

5 ft. x ( ) = ft.

Wall Cap 40 ft. x ( ) = ft.

90° Elbow 10 ft. x ( ) = ft.

45° Elbow 5 ft. x ( ) = ft.

90° Elbow 25 ft. x ( ) = ft.

45° Elbow 5 ft. x ( ) = ft.

Roof Cap 24 ft. x ( ) = ft.

Straight Duct 6˝ Round or 3¼˝

x 10˝ Rectangular

1 ft. x ( ) = ft.

Total Ductwork = ft.

* IMPORTANT: If a rectangular-to-round

transition adaptor is used, the bottom

corners of the damper will have to be cut

to ﬁt, using tin snips, in order to allow free

movement of the damper.

Equivalent lengths of duct pieces

are based on actual tests and reﬂect

the requirements for good venting

performance with any vent hood.

OTR_II_DE68-03587B-05_EN.indd 5 6/19/2019 3:56:00 PM

6

General information

• If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or

replacement.

• If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.

• If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by

arrangement between the customer and installer.

DAMAGE - SHIPMENT/INSTALLATION

HARDWARE PACKET

PART QUANTITY

Template

INSTALLATION

INSTRUCTIONS

Wood Screws

(¼˝ x 2˝)

1

Template

INSTALLATION

INSTRUCTIONS

Toggle Bolts

(and wing nuts)

(

3

/

16

˝ x 3˝)

2

Template

INSTALLATION

INSTRUCTIONS

Self-aligning

Machine Screws

(¼˝ - 28 x 3¼˝)

2

You will ﬁnd the installation hardware contained in a

packet with the unit. Check to make sure you have all

these parts.

NOTE: Some extra parts are included.

ADDITIONAL PARTS

PART QUANTITY

TOP CABINET TEMPLATE

REAR WALL TEMPLATE

Top Cabinet

Template

1

TOP CABINET TEMPLATE

REAR WALL TEMPLATE

Rear Wall Template 1

Installation

Instructions

1

Separately Packed

Grease Filter

2

Template

INSTALLATION

INSTRUCTIONS

Exhaust adaptor 1

PARTS INCLUDED

OTR_II_DE68-03587B-05_EN.indd 6 6/19/2019 3:56:00 PM

7

General information

# 1 and #2 Phillips

screwdriver

Pencil Ruler or tape measure and

straight edge

Carpenter square (optional)

Tin snips (for cutting

damper, if required)

Scissors (to cut

template, if necessary)

Electric drill with

3

/

16

˝, ½˝ and

⅝˝ drill bits

Filler blocks or scrap wood

pieces, if needed for top

cabinet spacing (used on

recessed bottom cabinet

installations only)

Gloves Saw (saber, hole or

keyhole)

Stud ﬁnder or Hammer

(optional)

Safety goggles

Level Duct and masking tape

TOOLS YOU WILL NEED

16½˝

30˝

2˝

30˝ min.

Bottom edge

of the cabinet

needs to be 30˝

or more from the

cooking surface.

Backsplash

66˝ or More

from the Floor

to the Top of the

Microwave

NOTES:

• The space between the cabinets must be 30˝ wide and

free of obstructions.

• If the space between the cabinets is greater than 30˝,

a Filler Panel Kit may be used to ﬁll in the gap between

the microwave oven and the cabinets. Your Owner’s

Manual contains the kit number for your model.

• This microwave oven is for installation over ranges up

to 36˝ wide.

• If you are going to vent your microwave oven to the

outside, see the Hood Exhaust Section for exhaust

duct preparation.

• When installing the microwave oven beneath

smooth, ﬂat cabinets, be careful to follow the

instructions on the top cabinet template for

power cord clearance.

MOUNTING SPACE

OTR_II_DE68-03587B-05_EN.indd 7 6/19/2019 3:56:01 PM

8

Step-by-step installation guide

1. PLACEMENT OF THE MOUNTING PLATE

A. REMOVING THE

MICROWAVE OVEN FROM

THE CARTON/REMOVING

THE MOUNTING PLATE

1. Remove the installation instructions, Exhaust

adaptor, ﬁlters, glass tray, and the small

hardware bag. Do not remove the Styrofoam

protecting the front of the oven.

2. Fold back all 4 carton ﬂaps fully against carton

sides. Then carefully roll the oven and carton

over onto the top side. The oven should be

resting in the Styrofoam.

Styrofoam

Carton

Styrofoam

3. Pull the carton up and o the oven.

4. Remove and properly discard plastic bags.

Screws

Mounting Plate

Screws

Mounting Plate

Screws

5. Remove the 2 screws from the mounting plate.

This plate will be used as the rear wall template

and for mounting.

NOTE: You will have to reuse two screws in original

loction of outcase after removing mounting plate.

B. FINDING THE WALL STUDS

Wall Studs

Center

Wall Studs

1. Find the studs using one of the following

methods:

A. Stud ﬁnder–a magnetic device which locates

nails.

OR

B. Use a hammer to tap lightly across the

mounting surface to ﬁnd a solid sound. This

will indicate a stud location.

2. After locating the stud(s), ﬁnd the center by

probing the wall with a small nail to ﬁnd the

edges of the stud. Then place a mark halfway

between the edges. The center of any adjacent

studs should be 16˝ or 24˝ from this mark.

3. Draw a line down the center of the studs.

THE MICROWAVE MUST BE CONNECTED TO

AT LEAST ONE WALL STUD.

OTR_II_DE68-03587B-05_EN.indd 8 6/19/2019 3:56:02 PM

9

Step-by-step installation guide

C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET

C

L

Plate position – beneath ﬂat bottom cabinet.

Draw a vertical line on the wall at

the center of the 30˝ wide space.

Tape the Rear Wall Template

onto the wall matching the

centerline and touching the

bottom of the cabinet.

At least 30˝

16½˝

C

L

Plate position – beneath framed recessed cabinet

bottom.

30˝ to Cooktop

Draw a vertical line on the wall at the center of the 30˝ wide

space.

Tape the Rear Wall Template onto the wall matching the centerline

and touching the bottom cabinet frame.

C

L

Plate position – beneath recessed bottom

cabinet with front overhang

Draw a line on the

back wall equal to the

depth of the front

overhang.

30" to Cooktop

Plate position – beneath recessed bottom cabinet with

front overhang.

30˝ to Cooktop

Draw a line on the

back wall equal to

the depth of the front

overhang.

Your cabinets may have decorative trim that interferes

with the microwave installation. Remove the decorative

trim to install the microwave properly and to make it

level.

THE MICROWAVE MUST BE LEVEL.

Use a level to make sure the cabinet bottom is level.

If the cabinets have a front overhang only, with no back

or side frame, install the mounting plate down the same

distance as the front overhang depth. This will keep the

microwave level.

1. Measure the inside depth of the front overhang.

2. Draw a horizontal line on the back wall an equal

distance below the cabinet bottom as the inside

depth of the front overhang.

3. For this type of installation with front overhang

only, align the mounting tabs with this horizontal

line, not touching the cabinet bottom as described

in Step D.

OTR_II_DE68-03587B-05_EN.indd 9 6/19/2019 3:56:04 PM

10

Step-by-step installation guide

D. ALIGNING THE WALL PLATE

C

L

CAUTION: Wear gloves to avoid cutting

fingers on sharp edges.

Area E

Hole B

Hole A

Centerline

notches

Draw a Vertical Line

on Wall from Center

of Top Cabinet

Draw a Horizontal line on wall from

bottom of “Rear Wall Template”.

Horizontal Line

Draw a Horizontal line on wall from bottom of “Rear

Wall Template”.

Draw a Vertical Line on

Wall from Center of Top

Cabinet

Horizontal Line

Horizontal Line Area E

Centerline

notches

Hole A

Hole B

CAUTION: Wear gloves to avoid cutting ﬁngers

on sharp edges.

1. Draw a Vertical line on the wall at the center

of the 30” wide space.

2. Draw a Horizontal line on the wall at the

bottom of the “Rear Wall Template”.

3. Drill ⅝” holes for toggle bolts on 3 locations

(Hole A, Hole B, Hole C) but if the location of

hole is same as that of stud, drill a

3

/

16

˝ hole

for wood screw. In other words, toggle bolt

can not be used to the location of stud.

NOTE: DO NOT MOUNT THE PLATE AT

THIS TIME.

NOTE: Holes A, B and C are inside area E.

If none of A, B and C is in a stud, ﬁnd a stud

somewhere in area E and draw a forth circle to

line up with the stud. It is important to use at

least one wood screw mounted ﬁrmly in a

stud to support the weight of the microwave. Set

the mounting plate aside.

OTR_II_DE68-03587B-05_EN.indd 10 6/19/2019 3:56:04 PM

11

Step-by-step installation guide

2. INSTALLATION TYPES (CHOOSE A, B OR C)

This microwave oven is compatible with the following

three types of ventilation:

A. Outside Top Exhaust (Vertical Duct)

B. Recirculating (Non-Vented Ductless)

C. Outside Back Exhaust (Horizontal Duct)

NOTE: This microwave is shipped assembled for

Outside Top Exhaust (except for non-vented models).

Select the type of ventilation required for your

installation and proceed to that section.

A. OUTSIDE TOP EXHAUST

(VERTICAL DUCT)

B. RECIRCULATING (NON-

VENTED DUCTLESS)

Adaptor in Place

for Outside

Top Exhaust

Adaptor in Place

for Outside Top

Exhaust

See page 12 See page 15

C. OUTSIDE BACK EXHAUST

(HORIZONTAL DUCT)

See page 19

OTR_II_DE68-03587B-05_EN.indd 11 6/19/2019 3:56:05 PM

12

Step-by-step installation guide

A. OUTSIDE TOP EXHAUST (VERTICAL DUCT)

INSTALLATION OVERVIEW

A1. Attach Mounting Plate to Wall

A2. Prepare Top Cabinet

A3. Mount the Microwave Oven

A4. Adjust the Exhaust Adaptor

A5. Connecting Ductwork

A1. ATTACH THE MOUNTING PLATE

TO THE WALL

Attach the plate to the wall using toggle bolts. At

least one wood screw must be used to attach the

plate to a wall stud.

1. Remove the toggle wings from the bolts.

2. Insert the bolts into the mounting plate through

the holes designated to go into drywall, and then

reattach the toggle wings to ¾˝ onto each bolt.

To use toggle bolts:

Wall

Toggle Wings

Toggle

Bolt

Bolt End

Spacing for Toggles More

Than Wall Thickness

Mounting

Plate

Spacing for Toggles More

Than Wall Thickness

Bolt End

Mounting

Plate

Toggle

Bolt

Wall

Toggle Wings

3. Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure the tabs on the mounting plate

touch the bottom of the cabinet when pushed

ﬂush against the wall and that the plate is properly

centered under the cabinet.

CAUTION: Be careful to avoid pinching your ﬁngers

between the back of the mounting plate and the wall.

4. Tighten all bolts. Pull the plate away from the

wall to help tighten the bolts.

A2. USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes for the top support screws, a

hole large enough for the power cord to ﬁt through,

and a cutout large enough for the exhaust adaptor.

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes

in the cabinet bottom.

OTR_II_DE68-03587B-05_EN.indd 12 6/19/2019 3:56:06 PM

13

Step-by-step installation guide

A3. INSTALLATION PROCEDURE FOR

EXHAUST ADAPTOR AND PROPER

DAMPER OPERATION CHECK

Blower Plate

Damper

Exhaust Adaptor

Retaining Hooks

Back of

Microwave

Oven

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes

in the cabinet bottom.

A4. MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use the handle

during installation.

NOTE: If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent

cutting of the cord.

NOTE: We recommend using ﬁller blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If ﬁller blocks are not used, case

damage may occur from over tightening screws.

NOTE: When mounting the microwave oven, thread

power cord through hole in bottom of top cabinet.

Keep it tight throughout Steps 1-3. Do not pinch cord

or lift oven by pulling cord.

1. Lift microwave, tilt it

forward, and hook slots

at back bottom edge

onto four lower tabs of

mounting plate.

2. Rotate front of

oven up against

cabinet bottom.

3. Insert a self-aligning screw through the top

center cabinet hole. Temporarily secure the oven

by turning the screw at least two full turns after

the threads have engaged. (It will be completely

tightened later.) Be sure to keep power cord

tight. Be careful not to pinch the cord,

especially when mounting ﬂush to bottom of

cabinet.

OTR_II_DE68-03587B-05_EN.indd 13 6/19/2019 3:56:06 PM

14

Step-by-step installation guide

Cabinet Front

Filler Block

Microwave Oven Top

Self-Aligning Screw

Equivalent to

Depth of

Cabinet Recess

Cabinet Bottom Shelf

Equivalent

to Depth of

Cabinet Recess

Cabinet Bottom Shelf

Microwave Oven Top

Cabinet Front

Filler Block

Self-Aligning Screw

4. Attach the microwave oven to the top cabinet.

5. Insert 2 self-aligning screws

through outer top cabinet

holes. Turn two full turns on

each screw.

6. Tighten center screw

completely.

7. Tighten the outer two screws to the top of the

microwave oven. (While tightening screws, hold

the microwave oven in place against the wall and

the top cabinet.)

8. Install grease ﬁlter. See the Owner’s Manual

packed with the microwave.

A5. ADJUST THE EXHAUST ADAPTOR

Open the top cabinet and adjust the exhaust adaptor

to connect to the house duct.

Damper

For Side-toSide

Adjustment,

Slide the Exhaust

Adaptor as Needed

Back of

Microwave

Oven

A6. CONNECTING DUCTWORK

House Duct

1. Extend the house duct down to connect to the

exhaust adaptor.

2. Seal exhaust duct joints using duct tape.

OTR_II_DE68-03587B-05_EN.indd 14 6/19/2019 3:56:07 PM

15

Step-by-step installation guide

B. RECIRCULATING (NON-VENTED DUCTLESS)

INSTALLATION OVERVIEW

B1. Attach Mounting Plate to Wall

B2. Prepare Top Cabinet

B3. Adjust Blower

B4. Mount Microwave Oven

B5. Install Charcoal Filter

B1. ATTACH THE MOUNTING PLATE

TO THE WALL

Attach the plate to the wall using toggle bolts. At

least one wood screw must be used to attach the

plate to a wall stud.

1. Remove the toggle wings from the bolts.

2. Insert the bolts into the mounting plate through

the holes designated to go into drywall, and then

reattach the toggle wings to ¾˝ onto each bolt.

To use toggle bolts:

Wall

Toggle Wings

Toggle

Bolt

Bolt End

Spacing for Toggles More

Than Wall Thickness

Mounting

Plate

Spacing for Toggles More

Than Wall Thickness

Bolt End

Mounting

Plate

Toggle

Bolt

Wall

Toggle Wings

3. Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure the tabs on the mounting plate

touch the bottom of the cabinet when pushed

ﬂush against the wall and that the plate is properly

centered under the cabinet.

CAUTION: Be careful to avoid pinching your ﬁngers

between the back of the mounting plate and the wall.

4. Tighten all bolts. Pull the plate away from the

wall to help tighten the bolts.

B2. USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes for the top support screws

and a hole large enough for the power cord to ﬁt

through.

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes

in the cabinet bottom.

OTR_II_DE68-03587B-05_EN.indd 15 6/19/2019 3:56:08 PM

16

Step-by-step installation guide

B3. ADAPTING MICROWAVE BLOWER

FOR RECIRCULATION

1. Remove and save screw that holds blower plate to

microwave.

2. Lift up the blower plate.

Back of

Microwave Oven

Blower

Retaining

Screws

NOTE: The exhaust adaptor with damper is not

needed for recirculating models. You may want to

save them for possible future use.

3. Carefully pull out the blower unit. The wires will

extend far enough to allow you to adjust the

blower unit.

CAUTION: Do not touch blade of blower

forpreventing crack and break. Hold outer case when

the blower pull out or back into.

4. Roll the blower unit 90° so that fan blade

openings are facing toward the front of the

microwave.

Before Roll

After Roll

5. Place the blower unit back into the opening.

CAUTION: Do not pull or stretch the blower unit

wiring. Make sure the wires are not pinched.

6. Remove the metal vent fan cover on the back of

the microwave by sliding it up.

7. Close the blower door. Slide blower shield onto

the top of the blower door opening.

8. Secure the blower to the microwave using the

blower retaining screws from Step 1.

Back of

Microwave Oven

Blower

Retaining

Screws

Blower Retaining

Screw

OTR_II_DE68-03587B-05_EN.indd 16 6/19/2019 3:56:10 PM

17

Step-by-step installation guide

B4. MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use the handle

during installation.

NOTE: If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent

cutting of the cord.

NOTE: We recommend using ﬁller blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If ﬁller blocks are not used, case

damage may occur from over tightening screws.

NOTE: When mounting the microwave oven, thread

power cord through hole in bottom of top cabinet.

Keep it tight throughout Steps 1-3. Do not pinch cord

or lift oven by pulling cord.

1. Lift microwave, tilt it

forward, and hook slots

at back bottom edge

onto four lower tabs of

mounting plate.

2. Rotate front of oven

up against cabinet

bottom.

3. Insert a self-aligning screw through the top

center cabinet hole. Temporarily secure the oven

by turning the screw at least two full turns after

the threads have engaged. (It will be completely

tightened later.) Be sure to keep power cord

tight. Be careful not to pinch the cord,

especially when mounting ﬂush to bottom of

cabinet.

Cabinet Front

Filler Block

Microwave Oven Top

Self-Aligning Screw

Equivalent to

Depth of

Cabinet Recess

Cabinet Bottom Shelf

Equivalent

to Depth of

Cabinet Recess

Cabinet Bottom Shelf

Microwave Oven Top

Cabinet Front

Filler Block

Self-Aligning Screw

4. Attach the microwave oven to the top cabinet.

5. Insert 2 self-aligning screws

through outer top cabinet

holes. Turn two full turns on

each screw.

6. Tighten center screw

completely.

7. Tighten the outer two screws to the top of the

microwave oven. (While tightening screws, hold

the microwave oven in place against the wall and

the top cabinet.)

8. Install grease ﬁlter. See the Owner’s Manual

packed with the microwave.

OTR_II_DE68-03587B-05_EN.indd 17 6/19/2019 3:56:11 PM

18

Step-by-step installation guide

B5. INSTALLING THE CHARCOAL

FILTER

1. Remove screws on top of grille using a #1

Phillips screwdriver.

2. Open the door.

3. Remove the grill.

• After push left, Pull the straight o.

Charcoal ﬁlter

4. Install the charocal filter. When properly installed,

the wire mesh of the filter should be visible from

the front.

5. Reinstall the grille and the screws.

6. Close the door.

Insert mesh-side up

OTR_II_DE68-03587B-05_EN.indd 18 6/19/2019 3:56:11 PM

19

Step-by-step installation guide

C. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)

INSTALLATION OVERVIEW

C1. Prepare Rear Wall

C2. Attach Mounting Plate to Wall

C3. Prepare Top Cabinet

C4. Adjust Blower

C5. Mount the Microwave Oven

C1. PREPARING THE REAR WALL FOR

OUTSIDE BACK EXHAUST

You need to cut an opening in the rear wall for

outside exhaust.

C

L

• Read the instructions on the REAR WALL

TEMPLATE.

• Tape it to the rear wall.

• Cut the opening, following the instructions of the

REAR WALL TEMPLATE.

OTR_II_DE68-03587B-05_EN.indd 19 6/19/2019 3:56:12 PM

20

Step-by-step installation guide

C2. ATTACH THE MOUNTING PLATE

TO THE WALL

Attach the plate to the wall using toggle bolts. At

least one wood screw must be used to attach the

plate to a wall stud.

1. Remove the toggle wings from the bolts.

2. Insert the bolts into the mounting plate through

the holes designated to go into drywall, and then

reattach the toggle wings to ¾˝ onto each bolt.

To use toggle bolts:

Wall

Toggle Wings

Toggle

Bolt

Bolt End

Spacing for Toggles More

Than Wall Thickness

Mounting

Plate

Spacing for Toggles More

Than Wall Thickness

Bolt End

Mounting

Plate

Toggle

Bolt

Wall

Toggle Wings

3. Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure the tabs on the mounting plate

touch the bottom of the cabinet when pushed

ﬂush against the wall and that the plate is properly

centered under the cabinet.

CAUTION: Be careful to avoid pinching your ﬁngers

between the back of the mounting plate and the wall.

4. Tighten all bolts. Pull the plate away from the

wall to help tighten the bolts.

C3. USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes for the top support screws, a

hole large enough for the power cord to ﬁt through,

and a cutout large enough for the exhaust adaptor.

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes

in the cabinet bottom.

C4. ADAPTING MICROWAVE BLOWER

FOR OUTSIDE BACK EXHAUST

1. Remove and save screws that hold the blower

plate and the blower motor to the microwave.

Back of

Microwave Oven

Blower

Retaining

Screws

2 Open the blower door by lifting it up at the back

of the microwave. Remove and save the blower

shield on the back of the microwave by sliding it

up. Remove and save the metal vent fan cover

on the back of the microwave by sliding it up.

OTR_II_DE68-03587B-05_EN.indd 20 6/19/2019 3:56:12 PM

La page charge ...

Samsung ME17H703SHB/AC Guide d'installation

Samsung ME17H703SHB/AC Guide d'installation

dans d''autres langues

Documents connexes

Autres documents