Chief LCD2TS Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
LCD2TS Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and
subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Personal injury possible with excessively long
column. Do NOT exceed column length of 24 inches!
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components including the display/projector does not
exceed 100 lbs (45.4 kg).
WARNING: Personal injury possible with excessively long
column. Do NOT exceed column length of 24 inches!
DIMENSIONS
Installation Instructions LCD2TS
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
LCD2TS Installation Instructions
4
7/32" (5.5mm) #2
1/2" (12.7mm)
TOOLS REQUIRED FOR INSTALLATION
D (4)
A (2) B (1)
C (1)
E(1)
F (1) G (8)
I (5)
5/16-18X3/8" J (8)
1/4-20X1-1/4"
K (8)
1/4-20X1-1/2" L (16) M (8)
H (8)
1/4-20 x 1-1/2"
PARTS
Installation Instructions LCD2TS
5
Assembly And Installation
For RPA Models Only
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment. It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
1. Set the base plate (B) on a flat stable work surface and
adjust the feet as necessary.
2. Thread the 1-1/2" pipe section (C) into the base plate and
tighten.
WARNING: Personal injury possible with excessively long
column. Do NOT exceed column length of 24 inches!
3. Secure NPT pipe to base plate using one 5/16-18 x 3/8" set
screw (I).
4. Attach RPA to projector arm (A) using four 1/4-20 X 1-1/2"
carriage bolts (H), four 1/4-20 acorn nuts (G) and 1/4" flat
washers (L). (See Figure 1)
Figure 1
5. Slide both projector arms (A) onto the 1-1/2" vertical pipe
section (C) and secure using two 5/16-18 x 3/8" set screws
(I) on each arm. (See Figure 2)
6. Thread 1-1/2" safety nut (F) onto threaded end of the 1-1/2"
pipe section. (See Figure 2)
7. Mount projector hanging bracket to your projector (see RPA
instructions).
8. Partially thread 10-24 thumbscrews onto 10-24 studs at top
of hanger bracket plate. The quantity of thumbscrews may
vary from three to six.
9. Align studs with key slots of RPA, slide RPA into place, and
secure RPA by tightening thumbscrews.
Figure 2
10. Adjust projector for correct registration.
For RPM Models Only
1. Proceed with Steps 1-3 under For RPA Models Only.
2. Place RPM on its top so that four screw holes are visible
through the square in the RPM base. (See Figure 3)
3. Insert four 1/4"-20x1-1/2" (K) button head cap screws into
the bottom of the RPM. (See Figure 3)
NOTE: The RPM base is not shown in Figure 3 for clarity only.
It should NOT be removed for this installation process.
Figure 3
4. Place four nylon spacers (M) onto the screws as shown in
Figure 3.
5. Tighten the screws through the nylon spacers and into the
two interface brackets (D). (See Figure 3)
(H)x4
Adjustable
Feet
RPA
4
(G)x4
(L)x4
(C)
(A)
5
(I)x2
(C)
6
(F)
(K)x4
RPM base not
shown for
clarity only.
(D)
RPM
2
4 screw
holes
(M)x4
LCD2TS Installation Instructions
6
6. Insert four 1/4"-20x1-1/4" (J) button head cap screws from
the top of the projector arm. (See Figure 4)
Figure 4
7. Place a 1/4" flat washer (L) onto each screw.
8. Hold the RPM (with interface brackets attached) to the
bottom of the projector arm and tighten the screws through
the washers and into the interface brackets.
9. Proceed with Steps 5 - 10 from For RPA Models Only
section
(A)
(L)x4
RPM not shown
for clarity only
8
(J)x4
Installation Instructions LCD2TS
7
LCD2TS Installation Instructions
Chief Manufacturing, a products division
of Milestone AV Technologies
8804-000053 RevB
2009 Milestone AV Technologies,
a Duchossois Group Company
www.chiefmfg.com
04/09
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
P+86-755-8996 9226
F+86-755-8996 9217
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief LCD2TS Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief LCD2TS Installation guide
Documents connexes
-
Chief CMA480W Guide d'installation
-
-
Chief Manufacturing LCD2C Manuel utilisateur
-
-
Chief RPA308 Guide d'installation
-
-
-
-
-