VTech CS6529-3 Manuel utilisateur

Marque: VTech

Modèle: CS6529-3

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

Telephone base

1 – X/DELETE

• Press to delete the message currently playing.

• When the phone is not in use, press twice to

delete all previously reviewed messages.

2 – /SKIP

• Press to skip to the next message.

3 – Message window

• Shows the number of messages, and other

information of the answering system or

telephone base.

4 – /PLAY/STOP

• Press to play messages.

• Press to stop message playback.

5 – VOL+ / VOL-

• Press to adjust the volume during message

playback.

• When the phone is not in use, press to adjust the

telephone base ringer volume.

6 – /REPEAT

• Press to repeat the playing message.

• Press twice to play the previous message.

7 –

• Page all system handsets.

8 – light

• Steady on in red when the line is in use or when

a handset is being registered.

• Flashes in red when there is an incoming call or

when handsets are being deregistered.

• Refer to the Bluetooth section for the IN USE light

indications when pairing and using a Bluetooth

headset.

9 – ANS ON/OFF

• Press to turn the answering system on or off.

Handset

1 – /

• Review the directory when the phone is not

in use.

• Scroll up while in a menu, or in the directory,

caller ID log or redial list.

• Move the cursor to the right when entering

numbers or names.

• Increase the listening volume during a call or

message playback.

• Review the caller ID log when the telephone is

not in use.

• Scroll down while in a menu, or in the

directory, caller ID log or redial list.

• Move the cursor to the left when entering

numbers or names.

• Decrease the listening volume during a call or

message playback.

2 –

• Show the menu.

• While in a menu, press to select an item, or save

an entry or setting.

3 –

• Hang up a call.

• Return to the previous menu.

• Press and hold to exit menu display without

making changes.

• Delete digits while predialing.

• Silence the handset ringer temporarily while the

phone is ringing.

• Press and hold to erase the missed call indicator

while the handset is not in use.

4 –

• Press and hold to turn on or off the quiet mode.

• Press repeatedly to show other dialing options

when reviewing a caller ID log entry.

5 –

• Press to start an intercom conversation or

transfer a call (for multi-handset models only).

6 –

• Mute the microphone during a call.

• Silence the handset ringer temporarily while the

phone is ringing.

• Delete the displayed entry while reviewing the

directory, caller ID log, or redial list.

• Delete digits or characters when entering

numbers or names.

7 – light

• On when the handset is charging.

8 –

• Review the last 10 numbers dialed.

• Press and hold to insert a dialing pause while

dialing or entering numbers into the directory.

9 –

• Make or answer a call.

• Answer an incoming call when you receive a

call waiting alert.

10 – Dialing keys

• Press repeatedly to add or remove 1 in front of

the caller ID log entry before dialing or saving

it to the directory.

• Press and hold to set or dial your voicemail

number.

• Switch to tone dialing temporarily during a call.

• Press to add a space when entering names.

11 –

• Make or answer a call using the handset

speakerphone.

• During a call, press to switch between the

speakerphone and the handset earpiece.

Display icons

The battery icon flashes when the

battery is low and needs charging.

The battery icon animates when the

battery is charging.

The battery icon becomes solid

when the battery is fully charged.

The handset ringer is turned off.

There are new voicemail received

from your telephone service

provider.

NEW The entry you are reviewing is new

in the caller ID log.

ANS ON The answering system is turned on.

10/16

MSG #MSG # The message number currently

playing and the total number of

messages.

Use the handset menu

1. Press MENU when the phone is not in use.

2. Press q or p until the screen displays the

desired feature menu.

3. Press SELECT.

• Press CANCEL to return to the previous menu.

• Press and hold CANCEL to exit completely.

Make a call

• Press or , and then dial the telephone

number.

Answer a call

• Press , or any dialing keys.

End a call

• Press OFF or put the handset back in the

telephone base or charger.

Speakerphone

• During a call, press on the handset to switch

between speakerphone and handset earpiece.

Volume

• During a call, press p/VOLUME/q to adjust

the listening volume.

Mute

The mute function allows you to hear the other party

but the other party cannot hear you.

1. During a call, press MUTE. The handset displays

Muted.

2. Press MUTE again to resume the conversation.

The handset displays Microphone on brieﬂy.

Join a call in progress (for two-handset

models only)

You can use up to two handsets at a time on an

outside call.

• When a handset is already on a call, press

or on another handset to join the call.

• To exit the call, press OFF on the handset or

place it in the telephone base or charger. The

call continues until all handsets hang up.

Call waiting

When you subscribe to call waiting service from

your telephone service provider, you hear an

alert tone if there is an incoming call while you are

already on a call.

• Press FLASH to put the current call on hold and

take the new call.

• Press FLASH at any time to switch back and

forth between calls.

Find handset

Use this feature to ﬁnd the system handset.

To start paging:

• Press FIND HANDSET on the telephone base

when not in use. All idle handsets ring and

display ** Paging **.

To end paging:

• Press FIND HANDSET at the telephone base.

-OR-

• Press , , OFF or any dialing keys on the

handset.

-OR-

• Place the handset in the telephone base or

charger.

NOTE: Do not press and hold FIND HS

for more than 4 seconds. It may lead to

handset deregistration.

Bluetooth®

Your telephone system is enhanced with

Bluetooth feature. You can pair a Bluetooth

headset to your telephone system and answer

calls with your Bluetooth headset.

NOTES:

Before you begin, make sure that your

Bluetooth enabled headset is not connected

to any other Bluetooth device. If you have

trouble pairing your Bluetooth headset to

your telephone system, try turning off the

Bluetooth feature of the nearby devices

that your Bluetooth headset has previously

paired.

Bluetooth wireless technology operates within

a short range (a maximum of approximately

15 feet) from the telephone base. Keep

connected headset within this range.

For more details about the Bluetooth feature,

read the online Complete user’s manual.

Pair and connect a Bluetooth headset

1. Set your Bluetooth headset to pairing mode.

Refer to your Bluetooth headset user’s manual

to learn how.

2. Press or on the handset.

3. Press and hold FIND HANDSET on the

telephone base for 4 seconds.

• The telephone then enters pairing mode.

• The IN USE LED ﬂashes in purple and red

alternately.

• To cancel pairing, press FIND HANDSET on

the telephone base.

4. When successfully paired and connected to the

Bluetoooth headset, the IN USE LED becomes

steady on in purple.

5. Press OFF on the handset or place the handset

in the telephone base or charger after pairing.

The IN USE LED becomes steady on in blue.

Bluetooth headset connection status:

• Pairing - while pairing to a Bluetooth headset,

the IN USE LED ﬂashes in purple and red

alternately.

• Connected - when successfully paired and

connected to a Bluetooth headset, the IN USE

LED becomes steady on in blue when the

telephone is not in use.

NOTE: When there is an incoming call, you hear

a ringing tone on your Bluetooth headset and

the IN USE LED ﬂashes in red. You can answer

the incoming call with your Bluetooth headset.

• Bluetooth headset in use - when the

connected Bluetooth headset is in use, the IN

USE LED ﬂashes in purple and blue alternately.

• Both telephone and Bluetooth headset are

in use - when both the telephone and the

connected Bluetooth headset are in use, the IN

USE LED becomes steady on in purple.

• No connection - the IN USE LED turns off.

Remove paired Bluetooth headset

1. Press or on the handset.

2. Press and hold FIND HANDSET on the

telephone base for 4 seconds. The paired

Bluetooth headset will be removed.

NOTES:

You can use your connected Bluetooth

headset to answer calls or end the call.

If you fail to connect your Bluetooth headset

to the telephone, re-try the pairing steps

above.

To pair another Bluetooth headset to the

telephone, perform the pairing steps above

and the current paired headset will be

replaced by the new Bluetooth headset.

While on a call using your Bluetooth headset,

keep your headset closer to the telephone

base (within 15 feet) and make sure that

there are no physical obstacles such as large

furniture or thick wall in between.

The Bluetooth® word mark and logos are owned by Bluetooth

SIG, Inc. and any use of such marks by Advanced American

Telephones and its parent, VTech Holdings Limited, is under

license. VTech Holdings Limited is a member of Bluetooth

SIG, Inc. Other trademarks and trade names are those of their

respective owners.

When using your telephone equipment, basic safety

precautions should always be followed to reduce the risk of

ﬁre, electric shock and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the

product.

3. Unplug this product from the wall outlet before cleaning.

Do not use liquid or aerosol cleaners. Use a damp cloth

for cleaning.

4. CAUTION: Do not install the telephone base at a height

above 2 meters.

5. Do not use this product near water such as near a bath tub,

wash bowl, kitchen sink, laundry tub or a swimming pool,

or in a wet basement or shower.

6. Do not place this product on an unstable table, shelf,

stand or other unstable surfaces.

7. Avoid placing the telephone system in places with extreme

temperature, direct sunlight, or other electrical devices.

Protect your phone from moisture, dust, corrosive liquids

and fumes.

8. Slots and openings in the back or bottom of the telephone

base and handset are provided for ventilation. To protect

them from overheating, these openings must not be

blocked by placing the product on a soft surface such as

a bed, sofa or rug. This product should never be placed

near or over a radiator or heat register. This product should

not be placed in any area where proper ventilation is not

provided.

9. This product should be operated only from the type of

power source indicated on the marking label. If you are

not sure of the type of power supply in your home or

ofﬁce, consult your dealer or local power company.

10. Do not allow anything to rest on the power cord. Do not

install this product where the cord may be walked on.

11. Never push objects of any kind into this product through

the slots in the telephone base or handset because they

may touch dangerous voltage points or create a short

circuit. Never spill liquid of any kind on the product.

12. To reduce the risk of electric shock, do not disassemble

this product, but take it to an authorized service facility.

Opening or removing parts of the telephone base or

handset other than speciﬁed access doors may expose

you to dangerous voltages or other risks. Incorrect

reassembling can cause electric shock when the product

is subsequently used.

13. Do not overload wall outlets and extension cords.

14. Unplug this product from the wall outlet and refer

servicing to an authorized service facility under the

following conditions:

• When the power supply cord or plug is damaged or

frayed.

• If liquid has been spilled onto the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operation instructions. Improper

adjustment of other controls may result in damage

and often requires extensive work by an authorized

technician to restore the product to normal operation.

• If the product has been dropped and the telephone

base and/or handset has been damaged.

• If the product exhibits a distinct change in performance.

15. Avoid using a telephone (other than cordless) during an

electrical storm. There is a remote risk of electric shock

from lightning.

16. Do not use the telephone to report a gas leak in the

vicinity of the leak. Under certain circumstances, a spark

may be created when the adapter is plugged into the

power outlet, or when the handset is replaced in its

cradle. This is a common event associated with the

closing of any electrical circuit. The user should not

plug the phone into a power outlet, and should not

put a charged handset into the cradle, if the phone is

located in an environment containing concentrations

of ﬂammable or ﬂame-supporting gases, unless there

is adequate ventilation. A spark in such an environment

could create a ﬁre or explosion. Such environments

might include: medical use of oxygen without adequate

ventilation; industrial gases (cleaning solvents; gasoline

vapors; etc.); a leak of natural gas; etc.

17. Only put the handset of your telephone next to your ear

when it is in normal talk mode.

18. The power adapter is intended to be correctly oriented

in a vertical or ﬂoor mount position. The prongs are not

designed to hold the plug in place if it is plugged into a

ceiling, under-the-table or cabinet outlet.

19. For pluggable equipment, the socket-outlet shall

be installed near the equipment and shall be easily

accessible.

20. CAUTION: Use only the batteries indicated

in this manual. There may be a risk of

explosion if a wrong type of battery is used for the

handset. Use only the supplied rechargeable batteries

or replacement batteries for the handset. Do not

dispose of batteries in a ﬁre. They may explode.

Disposed of used batteries according to the instruction.

• Do not use the battery in following conditions:

»High or low extreme temperature during use,

storage or transportation.

»Replacement of a battery with an incorrect type

that can defeat a safeguard.

»Disposal of a battery into ﬁre or a hot oven, or

mechanically crushing or cutting of a battery, that

can result in an explosion.

»Leaving a battery in an extremely high

temperature surrounding environment that can

result in an explosion or the leakage of ﬂammable

liquid or gas.

»A battery subjected to extremely low air pressure

that can result in an explosion or the leakage of

ﬂammable liquid or gas.

21. Use only the adapter included with this product.

Incorrect adapter polarity or voltage can seriously

damage the product.

22. The applied nameplate is located at the bottom or near

of the product.

SAVE THESE INSTRUCTIONS

Battery

• Use only the battery provided or equivalent. To order a

replacement, visit our website at

www.vtechphones.com or call 1 (800) 595-9511. In

Canada, go to phones.vtechcanada.com or call

1 (800) 267-7377.

• Do not dispose of the battery in a ﬁre. Check with

local waste management codes for special disposal

instructions.

• Do not open or mutilate the battery. Released

electrolyte is corrosive and may cause burns or injury

to the eyes or skin. The electrolyte may be toxic if

swallowed.

• Exercise care in handling batteries in order not to create

a short circuit with conductive materials.

• Charge the battery provided with this product only

in accordance with the instructions and limitations

speciﬁed in this manual.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless

telephones):

Wireless Technology Research, LLC (WTR), an independent

research entity, led a multidisciplinary evaluation of the

interference between portable wireless telephones and

implanted cardiac pacemakers. Supported by the U.S. Food

and Drug Administration, WTR recommends to physicians

that:

Pacemaker patients

• Should keep wireless telephones at least six inches from

the pacemaker.

• Should NOT place wireless telephones directly over

the pacemaker, such as in a breast pocket, when it is

turned ON.

• Should use the wireless telephone at the ear opposite

the pacemaker.

WTR’s evaluation did not identify any risk to bystanders with

pacemakers from other persons using wireless telephones.

About cordless telephones

• Privacy: The same features that make a cordless

telephone convenient create some limitations.

Telephone calls are transmitted between the telephone

base and the cordless handset by radio waves, so

there is a possibility that the cordless telephone

conversations could be intercepted by radio receiving

equipment within range of the cordless handset. For

this reason, you should not think of cordless telephone

conversations as being as private as those on corded

telephones.

• Electrical power: The telephone base of this cordless

telephone must be connected to a working electrical

outlet. The electrical outlet should not be controlled by

a wall switch. Calls cannot be made from the cordless

handset if the telephone base is unplugged, switched

off or if the electrical power is interrupted.

• Potential TV interference: Some cordless telephones

operate at frequencies that may cause interference

to televisions and VCRs. To minimize or prevent such

interference, do not place the telephone base of the

cordless telephone near or on top of a TV or VCR.

If interference is experienced, moving the cordless

telephone farther away from the TV or VCR often

reduces or eliminates the interference.

• Rechargeable batteries: Exercise care in handling

batteries in order not to create a short circuit with

conducting material such as rings, bracelets and keys.

The battery or conductor may overheat and cause harm.

Observe proper polarity between the battery and the

battery charger.

• Nickel-metal hydride rechargeable batteries: Dispose

of these batteries in a safe manner. Do not burn or

puncture the battery. Like other batteries of this type,

if burned or punctured, they could release caustic

material which could cause injury.

Go to www.vtechphones.com (US) to register your

product for enhanced warranty support and latest

VTech product news.

Go to phones.vtechcanada.com (Canada) for the latest

VTech product news.

Speciﬁcations are subject to change without notice.

CS6529-X_BT_HS59VSD-BS56VSD_US-CAN_ACIB_V1_231214

BT_HS59VSD-BS56VSD

What’s in the box Setup

Overview

After the telephone is installed or power returns

following a power outage and battery depletion,

the handset will prompt you to set the date and

time.

Date and time

When the handset prompts, follow the steps below

to set the date and time.

1. Use the dialing keys (0-9) to enter the month

(MM), date (DD) and year (YY). Then press

SELECT.

2. Use the dialing keys (0-9) to enter the hour

(HH) and minute (MM). Then press q or p to

choose AM or PM.

3. Press SELECT to save.

NOTE: If you have skipped the prompt,

you can set up again by pressing MENU.

Scroll to choose Set date/time and press

SELECT. Then, follow the steps above.

Change LCD language settings

You can select English, French, or Spanish to be

used in all screen displays:

1. Press MENU when the handset is not in use.

2. Press q or p to scroll to Settings and then

press SELECT.

3. Press SELECT to choose LCD language.

4. Press q or p to choose English, Français or

Español, and then press SELECT twice to save.

NOTE: If you accidentally set the LCD

language to Spanish or French, press

MENU and then enter *364# to change

the handset LCD language back to

English while the handset is not in use.

Important safety instructions

Redial list

Each handset stores the last 10 telephone numbers

dialed. When there are already 10 entries, the

oldest entry is deleted to make room for the new

entry.

Review and dial a redial list entry

1. Press REDIAL when the handset is not in use.

2. Press q, p or REDIAL repeatedly until the

desired entry displays.

3. Press or to dial.

Delete a redial list entry

• When the desired redial entry displays, press

DELETE.

Transfer a call

While on an outside call, you can transfer the call

from one handset to another.

1. Press MENU on your handset during a call.

2. Press q or p to scroll to Transfer, and then

press SELECT.

3. If you have three or more handsets, use the

dialing keys to enter a destination handset

number.

4. To answer the intercom call, press , or any

dialing key on the destination handset.

Intercom

Use the intercom features for conversations

between two handsets.

1. Press INT on your handset when not in use.

If you have three or more handsets, use the

dialing keys to enter a destination handset

number.

2. To answer the intercom call, press , , INT

or any dialing key on the destination handset.

3. To end the intercom call, press OFF or place the

handset back in the telephone base or charger.

Answer an incoming call during an intercom

call

If you receive an incoming call during an intercom

call, there is an alert tone.

• To answer the outside call, press . The

intercom call ends automatically.

• To end the intercom call without answering

the outside call, press OFF. The telephone

continues to ring.

Call transfer using intercom

While on an outside call, you can use the intercom

feature to transfer the call from one handset to

another.

1. Press INT on your handset during a call. The

current call is put on hold.

• If you have three or more handsets, use the

dialing keys to enter a destination handset

number.

2. To answer the intercom call on the destination

handset, press , , INT or any dialing key on

the destination handset. You can now have a

private conservation before transferring the call.

3. From this intercom call, you have the following

options:

• You can let the destination handset join

you on the outside call in a three-way

conversation. Press and hold INT on the

originating handset.

• You can transfer the call. Press OFF, or place

your handset back in the telephone base

or charger. The destination handset is then

connected to the outside call.

• You can press INT to switch between the

outside call (Outside call displays) and the

intercom call (Intercom displays).

• The destination handset can end the

intercom call by pressing OFF, or by placing

the handset back in the telephone base or

charger. The outside call continues with the

original system handset.

Directory

The directory can store up to 50 entries, which are

shared by all handsets. Each entry may consist of a

telephone number up to 30 digits, and a name up

to 15 characters.

Add a directory entry

1. Enter the number when the phone is not in use.

Press MENU, then go to Step 3.

-OR-

Press MENU when the phone is not in use.

Scroll to Directory and then press SELECT. Press

SELECT again to choose Add contact.

2. Use the dialing keys to enter the number.

-OR-

Copy a number from the redial list by pressing

REDIAL and then press q, p or REDIAL

repeatedly to select a number. Press SELECT to

copy the number.

3. Press SELECT to move on to enter the name.

4. Use the dialing keys to enter the name.

Additional key presses show other characters of

that particular key.

5. Press SELECT to save.

While entering names and numbers, you can:

• Press DELETE to backspace and erase a digit or

character.

• Press and hold DELETE to erase the entire entry.

• Press q or p to move the cursor to the left or

right.

• Press and hold PAUSE to insert a dialing pause

(for entering numbers only).

• Press 0 to add a space (for entering names

only).

Review a directory entry

Entries are sorted alphabetically.

1. Press when the phone is not in use.

2. Scroll to browse through the directory, or use

the dialing keys to start a name search.

-OR-

1. Press MENU when the phone is not in use.

2. Scroll to Directory, and then press SELECT.

3. Scroll to Review, and then press SELECT.

4. Scroll to browse through the directory.

Delete a directory entry

1. When the desired entry displays, press DELETE.

2. When the handset displays Delete contact?,

press SELECT.

Edit a directory entry

1. Search for or review the directory entries (see

Review a directory entry).

2. When the desired entry displays, press SELECT.

3. Use the dialing keys to edit the number, then

press SELECT.

4. Use the dialing keys to edit the name, then

press SELECT.

Dial a directory entry

1. Search for or review the directory entries (see

Review a directory entry).

2. When the desired entry appears, press or

to dial.

Speed dial

You can copy up to 9 directory entries into the

speed dial locations (0 and 2-9) so that you can dial

these numbers using fewer keys than usual.

The speed dial memory locations are stored in the

telephone base and are shared by all handsets.

Changes made to the speed dial entries on one

handset apply to all.

Assign a speed dial entry

1. Press MENU when the phone is not in use.

2. Scroll to Directory, and then press SELECT.

3. Scroll to Speed dial, and then press SELECT.

4. Press q or p or the dialing keys (0 or 2-9) to

choose the desired speed dial location.

5. Press SELECT. The screen displays Copy from

DIR... and then the ﬁrst entry in the directory.

6. Scroll to browse to the desired entry.

-OR-

Use the alphabetical search to ﬁnd the desired

entry.

7. Press SELECT to save. You hear a conﬁrmation.

The name (up to 12 characters) appears in the

selected speed dial location.

NOTES:

If the directory is empty, when you press

SELECT in Step 5, the screen displays

Directory empty.

If the speed dial location you selected

is occupied, the new directory entry

you selected replaces the old one. Take

caution not to replace entries you do

not wish to delete from the speed dial

locations.

Reassign a speed dial entry

1. Press MENU when the phone is not in use.

2. Scroll to Directory, and then press SELECT.

3. Scroll to Speed dial, and then press SELECT.

4. Press q or p or the dialing keys (0 or 2-9) to

choose the speed dial location you want to

reassign.

5. Press SELECT twice. The screen displays

Reassign SD.

6. Press SELECT. The screen displays Copy from

DIR... and then the ﬁrst entry of the directory.

7. Scroll to browse to the desired entry.

-OR-

Use the alphabetical search to ﬁnd the desired

entry.

8. Press SELECT to save. You hear a conﬁrmation.

The name (up to 12 characters) appears in the

selected speed dial location.

Dial a speed dial number

• Press and hold a dialing key (0 or 2-9) to dial the

number stored in the corresponding speed dial

location.

When the speed dial location is empty, the screen

displays the speed dial list. See Assign a speed dial

entry to add a new entry.

Delete a speed dial entry

1. Press MENU when the phone is not in use.

2. Scroll to Directory, and then press SELECT.

3. Scroll to Speed dial, and then press SELECT.

4. Press q or p or the dialing keys (0 or 2-9) to

choose the desired speed dial location, then

press DELETE. The screen displays Clear SD #X?.

5. Press SELECT to conﬁrm. You hear a conﬁrmation

tone.

NOTE:

Deleting the speed dial entries does not

affect the entries in the directory.

CS6529

CS6529-14

CS6529-15

CS6529-16

CS6529-17

CS6529-19

CS6529-2

CS6529-25

CS6529-26

CS6529-3

CS6529-4

CS6529-4B

CS6529-5

Abridged user’s manual

Scan the QR code for

support information

(US)

(CA)

Your telephone package contains the following

items. Save your sales receipt and original packaging

in case it is necessary to ship your telephone for

warranty service.

Abridged

user’s

manual

1 set for CS6529-2/

CS6529-25/CS6529-26 |

2 sets for CS6529-3 |

3 sets for CS6529-4/

CS6529-4B

4 sets for CS6529-5

1 set for CS6529/

CS6529-14/CS6529-15/

CS6529-16/CS6529-17/

CS6529-19 |

2 sets for CS6529-2/

CS6529-25/CS6529-26 |

3 sets for CS6529-3 |

4 sets for CS6529-4/

CS6529-4B

5 sets for CS6529-5

Install and Connect | Mount (optional)

Install the battery

Connect and charge

Connect the telephone base

If you subscribe to digital subscriber line (DSL)

high-speed Internet service through your

telephone line, make sure you connect a DSL

ﬁlter (not included) to the telephone wall jack.

Mount (optional)

Remove the telephone line cord

from the telephone wall jack, and the

telephone base power adapter from

the electrical outlet (if necessary).

Position the telephone base against the wall

mount bracket with the extended tabs marked B

on top. Insert the extended tabs marked B on the

wall mount bracket into the slots marked B on the

back of the telephone base. Push the telephone

base down until it clicks securely.

CHARGE light

remains on

when charging.

Telephone operations

The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by

Advanced American Telephones and its parent, VTech Holdings Limited, is under license. VTech Holdings

Limited is a member of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective

owners.

Caller ID

If you subscribe to caller ID service, information

about each caller appears after the ﬁrst or

second ring. If you answer a call before the caller

information appears on the screen, it will not be

saved in the caller ID log.

The caller ID log stores up to 50 entries. Each entry

has up to 24 digits for the phone number and 15

characters for the name.

If the telephone number has more that 15 digits,

only the last 15 digits appear. If the name has more

than 15 characters, only the ﬁrst 15 characters are

shown and saved in the caller ID log.

Review a caller ID log entry

1. Press CID when the phone is not in use.

2. Scroll to browse through the caller ID log.

-OR-

1. Press MENU when the phone is not in use.

2. Scroll to Caller ID log, and then press SELECT.

3. Press SELECT to choose Review.

4. Scroll to browse through the caller ID log.

• Press # or 1 repeatedly if you need to add or

remove 1 in front of the phone number.

Missed call indicator

When there are calls that have not been reviewed

in the caller ID log, the handset displays XX missed

calls.

Each time you review a caller ID log entry marked

NEW, the number of missed calls decreases by

one.

When you have reviewed all the missed calls, the

missed call indicator no longer displays.

If you do not want to review the missed calls

one by one, press and hold CANCEL on the idle

handset to erase the missed call indicator. All the

entries are then considered old.

Dial a caller ID log entry

1. Search for or review the caller ID log entries

(see Review a caller ID log entry).

2. When the desired entry appears, press or

to dial.

Save a caller ID log entry to the directory

1. Search for or review the caller ID log entries

(see Review a caller ID log entry).

2. When the desired caller ID log entry displays,

press SELECT.

3. Use the dialing keys to edit the number, if

necessary. Then press SELECT.

4. Use the dialing keys to edit the name, if

necessary. Then press SELECT.

Delete the caller ID log entries

1. Search for or review the caller ID log entries

(see Review a caller ID log entry).

2. When the desired caller ID log entry displays,

press DELETE.

To delete all caller ID log entries:

1. Press MENU when the phone is not in use.

2. Scroll to Caller ID log and then press SELECT.

3. Scroll to Del all calls and then press SELECT.

4. Press SELECT to conﬁrm.

Sound settings

Key tone

You can turn the key tone on or off.

1. Press MENU when the handset is not in use.

2. Scroll to Settings and then press SELECT.

3. Scroll to choose Key tone, then press SELECT.

4. Press q or p to choose Key tone:On or Key

tone:Off, then press SELECT to save.

Ringer tone

You can choose from different ringer tones for

each handset.

1. Press MENU when the handset is not in use.

2. Scroll to Ringers and then press SELECT.

3. Scroll to choose Ringer tone, then press

SELECT.

4. Press q or p to sample each ringer tone, then

press SELECT to save.

NOTE: If you turn off the ringer volume,

you will not hear ringer tone samples.

Ringer volume

You can adjust the handset ringer volume level, or

turn the ringer off.

1. Press MENU when the handset is not in use.

2. Scroll to Ringers and then press SELECT.

3. Press SELECT again to choose Ringer volume.

4. Press q or p to sample each volume level,

then press SELECT to save.

NOTES:

• If you turn off the volume, the handset

will be silenced and display icon.

• When the ringer volume is set to Off,

the handset still rings when you press

FIND HANDSET at the telephone base.

Temporary ringer silencing

When the telephone is ringing, you can temporarily

silence the ringer without disconnecting the call. The

next call rings normally at the preset volume.

To silence the handset ringer:

• Press OFF or MUTE on the handset. The handset

displays and Ringer muted brieﬂy.

Quiet mode

You can turn on the quiet mode for a period of

time. During this period, all tones (except paging

tone) and call screening are muted.

1. Press and hold on the handset when it

is not in use.

2. Use the dialing keys (0-9) to enter the duration,

and then press SELECT to save.

• To turn off the quiet mode, press and hold

on the handset when it is not in use.

About the built-in answering

system and voicemail service

For message recording, your telephone has a

built-in answering system, and it also supports

voicemail service offered by your telephone

service provider (subscription is required, and fee

may apply).

The main differences between them are:

Category Built-in

answering

system

Voicemail from

telephone

service

Storage Messages are

stored in the

telephone base.

Messages are

stored in a

server or system

provided by

your telephone

service

provider.

Your messages

will not be

deleted

automatically.

You have to

delete your

messages

manually.

Your messages

may be

automatically

deleted after a

period of time.

Contact your

telephone

service

provider for

more details.

Display

new

message

When you

received new

messages,

the handset

displays XX new

messages, and

the message

window on the

telephone base

ﬂashes.

When you

received new

messages,

the handset

displays and

New voicemail.

Method

to retrieve

messages

To retrieve

messages:

• Press on

the telephone

base; or

• Press MENU on

the handset,

and then select

Play messages;

• Access

remotely with

an access code.

To retrieve

messages, you

need an access

number and/

or a passcode

provided by

your telephone

service

provider.

New message indication

When there are new messages in the built-in

answering system, the handset displays XX new

messages, and the message window on the

telephone base ﬂashes.

Message

window

display

Description

0No messages.

0 (ﬂashing) After a power failutre, the number

in the message window ﬂashes to

indicate that the date and time

need to be set.

1-99 Total number of old messages

and memos recorded.

The current message number

during old message playback.

0-99

(ﬂashing)

• Total number of new

messages and memos. The

number ﬂashes when there

are new messages that have

not been reviewed.

• Current message number

during new message

playback.

• After a power failure, the

number in the message

window ﬂashes.

• Indicate that the date and time

need to be set.

1-99 & F

(alternating)

Memory is full. Messages must be

deleted before new messages

can be recorded.

1- 8The telephone base speaker

volume level while adjusting.

0- 6The telephone base ringer level

while adjusting.

Message

window

display

Description

-- • The answering system is being

programmed by a system

handset.

• The answering system is

answering a call or recording a

memo or announcement.

• The answering system is being

accessed remotely.

• The directory or caller ID log

is being accessed by a system

handset.

Turn on/ off the answering

system

The answering system must be turned on to

answer and record messages.

When the answering system is turned on, the

ANS ON/OFF light on the telephone base turns

on and ANS ON displays on the handset.

Press ANS ON/OFF on the base to turn the

answering system on or off. - OR -

1. Press MENU when the handset is not in use.

2. Press q or p to choose Answering sys and

then press SELECT.

3. Press q or p to choose Answer on/off and

then press SELECT.

4. Press q or p to choose Answer:On or

Answer:Off, then press SELECT to save.

Answering system settings

Set your built-in answering system

The answering system can record and store

up to 99 messages. Each message can be

up to 3 minutes in length. The total storage

capacity for the announcement, messages and

memos is approximately 14 minutes. The actual

recording time depends on individual message

characteristics. Messages remain available for

replay until you delete them.

If the answering system has less than 3 minutes of

recording time left, “Less than 3 minutes to record”

is announced before the message playback and

Rec mem low appears on the handset screen.

If the memory is full, the answering system

announces, “Memory is full.” The number of

messages and F ﬂash, alternatively, in the message

window, and Rec mem full appears on the handset

screen. You must delete some messages before

recording new ones.

Your answering system allows you to set your

announcement, to save and delete messages,

activate call screening, to set number of rings

before pick up, and to access remotely.

Voice language

NOTE: This feature is available in Canada

version only.

The voice prompt language is preset to English.

You can select English or French to be used for the

voice prompts in your answering system.

1. Press MENU when the handset is not in use.

2. Press q or p to choose Answering sys and

then press SELECT.

3. Press q or p to choose Ans sys setup and then

press SELECT.

4. Press q or p to choose Voice language and

then press SELECT.

5. Press q or p to choose English or Français and

then press SELECT.

Announcement

Your outgoing announcement plays when calls are

answered by the answering system. The telephone

has a default outgoing announcement, “Hello,

please leave a message after the tone.” You can

use this announcement, or record your own.

Record a new outgoing announcement:

The announcement can be up to 90 seconds in

length.

1. Press MENU when the handset is not in use.

2. Press q or p to choose Answering sys and

then press SELECT.

3. Press SELECT to choose Announcement.

4. The screen displays Play [2] Del [3] Rec [7] and

it announces, “To play, press 2. To record, press

7.” Press 7 to record.

5. The handset announces, “Record after the tone.

Press 5 when you are done.” and it displays

Recording... Stop [5].

6. After the tone, speak towards the handset

microphone.

7. Press 5 when ﬁnished. The handset plays back

the recorded announcement. Press 5 or OFF to

stop the playback at any time.

To listen to the recorded announcement again,

wait after playback has completed, then press

NOTE: Announcements shorter than two

seconds will not be recorded.

Play your announcement:

1. Press MENU when the handset is not in use.

2. Press q or p to choose Answering sys and

then press SELECT.

3. Press SELECT to choose Announcement.

4. The screen displays Play [2] Del [3] Rec [7] and

it announces, “To play, press 2. To record, press

7.” Press 2 to play the current announcement.

Options during playback:

1. Press VOL q or VOL p to adjust the listening

volume.

2. Press 5 or OFF to stop at any time.

Delete your announcement:

1. Press MENU when the handset is not in use.

2. Press q or p to choose Answering sys and

then press SELECT.

3. Press SELECT to choose Announcement.

4. The screen displays Play [2] Del [3] Rec [7] and

it announces, “To play, press 2. To record, press

7.” Press 3 or DELETE to delete your recorded

announcement. The handset displays Annc

deleted and announces “Announcement

deleted.”

NOTE: After you deleted your own recorded

announcement, the answering system

answers calls with the default announcement.

Set number of rings

You can set the answering system to answer an

incoming call after two, three, four, ﬁve or six

rings; or toll saver.

If you choose toll saver, the answering system

answers a call after two rings when you have new

messages, or after four rings when you have no

new messages. This enables you to check for new

messages and avoid paying unnecessary long

distance charges if you are calling from outside

your local area.

1. Press MENU when the handset is not in use.

2. Press q or p to choose Answering sys and

then press SELECT.

3. Press q or p to choose Ans sys setup and then

press SELECT.

4. Press q or p to choose # of rings and then

press SELECT.

5. Press q or p to choose from 6, 5, 4, 3, 2, or Toll

saver, then press SELECT to save.

Turn on or off the message alert tone

When the message alert tone is set to On, and

there is at least one new message, the telephone

base beeps every 10 seconds. The tone stops

when all new messages have been reviewed.

1. Press MENU when the handset is not in use.

2. Press q or p to choose Answering sys and

then press SELECT.

3. Press q or p to choose Ans sys setup and then

press SELECT.

4. Press q or p to choose Msg alert tone and

then press SELECT.

5. Press q or p to choose Tone:On or Tone:Off,

then press SELECT to save.

NOTE: The message alert tone beeps only if

all the following conditions are met.

- Anwering system is on.

- Messsage alert tone setting is on.

- There are new messages.

Playback messages

You can listen to messages at the telephone base

or on a cordless handset. When playback begins,

the total number of messages is annouced. Before

each message, you hear the day and time of the

recording. After the last message, you hear, “End

of messages.” Make sure you set the date and

time correctly. Refer to Set date and time for more

details.

To listen to messages at the base:

• Press /PLAY when the phone is not in use.

When you have no message in the answering

system, the telephone base announces, “You

have no message.”

Options during playback

• Press pVOL + or qVOL - to adjust the listening

volume.

• Press /SKIP to skip to the next message.

• Press /REPEAT to repeat the playing

message. Press /REPEAT twice to listen to the

previous message.

• Press X/DELETE to delete the playing message.

The telephone base advances to the next

message.

• Press /STOP to stop the playback.

To listen to messages with the handset:

1. Press MENU when the handset is not in use. The

handset displays Play messages.

2. Press SELECT. If you have either new or old

messages, the messages play automatically.

• The system announces the number of

messages, and then begins playback. The

message sequence is shown on the handset’s

screen.

3. Press OFF to stop the playback.

Options during playback

• Press q/VOLUME or p/VOLUME to adjust the

listening volume.

• Press 6 to skip to the next message.

• Press 4 to repeat the playing message. Press 4

twice to listen to the previous message.

• Press 3 or MUTE/DELETE to delete the playing

message. The telephone base advances to the

next message.

• Press OFF to stop the playback.

Delete all messages

Using the base

1. Press X/DELETE when the telephone is not in

use. The telephone announces - To delete all old

messages, press DELETE again.

2. Press X/DELETE again. All previously reviewed

messages are erased and the telephone

announces - All old messages deleted.

Using the handset

1. Press MENU when the handset is not in use.

2. Press q or p to choose Answering sys and

then press SELECT.

3. Press q or p to choose Delete all old and then

press SELECT.

4. Press SELECT to conﬁrm. The handset displays

Deleting... and then No old messages. It

returns to the previous menu, and you hear a

conﬁrmtion tone.

Answering system remote access

You can reach your answering system remotely by

dialing your home telephone number from any

touch-tone telephone.

1. Dial your telephone number from any touch-

tone telephone.

2. Once the system plays your announcement,

enter the two-digit remote access code (19 is

the default code).

• The system automatically announces the

number of new or old messages (if any), and

then begins to play them.

You can also enter the following remote commands.

Command Description

1Play all messages.

2Play only new messages.

3Delete the current message (during

playback).

33 Delete all old messages.

4Repeat the current message (during

playback).

5Stop.

*5 Hear a list of remote commands.

6Skip to the next message (during

playback).

*7 Record a new announcement.

8 End the call.

0 Turn the answering system on or off.

3. Hang up or press 8 to end the call.

NOTES:

• If you do not press any key after you

enter the remote access code, all new

messages play. If there are no new

messages, all old messages play.

• Once the new messages have played,

the telephone announces the help

menu options. If you do not press any

key within 20 seconds, the remote

access call automatically disconnects.

• When the answering system is turned

off, the telephone answers after 10

rings, and announces, “Please enter

your remote access code.”

• When the memory is full, the answering

system answers incoming calls after 10

rings and announces, “Memory is full.

Enter your remote access code.”

Change remote access code

1. Press MENU when the handset is not in use.

2. Press q or p to choose Answering sys and

then press SELECT.

3. Press q or p to choose Ans sys setup and then

press SELECT.

4. Press q or p to choose Remote code and then

press SELECT.

5. Use the dialing keys to enter a two-digit

number.

-OR-

Press q or p to scroll to a desired two-digit

number.

6. Press SELECT to conﬁrm.

Call intercept while using answering system

When a caller is leaving a message on your

answering system, you can stop recording and talk

to the caller by pressing or on the handset.

Recording memo

Memos are your own recorded messages used

as reminders for yourself or others using the

same answering system. You can record your

own memos using a system handset. Playback

and delete them in the same way as incoming

messages.

1. Press MENU when the handset is not in use.

2. Press q or p to choose Answering sys and

then press SELECT.

3. Press q or p to choose Record memo and

then press SELECT. The handset displays

Recording... Stop [5] and announces, “Record

after the tone. Press 5 when you are done.”

4. Speak towards the handset microphone. Press 5

or OFF when you ﬁnish recording. The handset

announces “Recorded.”

NOTES:

• If you record a memo when the

answering system memory is full, the

system announces, “Memory is full.”

• Each memo can be up to three minutes

in length. Memos shorter than two

second are not recorded.

• When the answering system has less

than three minutes of recording time

left, the handset announces, “Less than

three minutes to record,” and displays

Rec mem low.

For C-UL compliance only

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de blessures corporelles

ou d’électrocution, suivez toujours ces mesures préventives de

base lorsque vous utilisez votre téléphone :

1. Lisez et comprenez bien toutes les instructions.

2. Observez toutes les instructions et mises en garde inscrites

sur l’appareil.

3. Débranchez ce téléphone de la prise murale avant de le

nettoyer. N’utilisez pas de nettoyeurs liquides ni en aérosol.

N’utilisez qu’un chiffon doux et légèrement humecté.

4. ATTENTION: Ne pas installer le socle téléphonique à une

hauteur supérieure à 2 mètres.

5. N’utilisez pas ce produit près de l’eau, tel que près d’un

bain, d’un lavabo, d’un évier de cuisine, d’un bac de lavage

ou d’une piscine, ou dans un sous-sol humide ou sous la

douche.

6. Ne déposez pas ce téléphone sur un chariot, support

ou table chancelants. L’appareil pourrait tomber et être

sérieusement endommagé.

7. Évitez d’installer le système téléphonique dans les endroits

soumis à une température extrême, à la lumière directe du

soleil ou à proximité immédiate d’autres appareils électriques

ou électroniques. Protégez votre téléphone contre les

sources d’humidité, la poussière, les vapeurs et les liquides

corrosifs.

8. Le boîtier de l’appareil est doté de fentes et d’ouvertures

d’aération situées à l’arrière ou en dessous. Aﬁn d’empêcher

la surchauffe, ces ouvertures ne doivent pas être obstruées

en plaçant l’appareil sur un lit, divan, tapis ou autre surface

similaires. Ne placez pas cet appareil à proximité d’un

élément de chauffage ni d’une plinthe électrique. De plus,

ne l’installez pas dans une unité murale ou un cabinet fermé

qui ne possède pas d’aération adéquate.

9. Ne faites fonctionner cet appareil qu’avec le type

d’alimentation indiqué sur les étiquettes de l’appareil. Si

vous ne connaissez pas le voltage de votre maison, consultez

votre marchand ou votre fournisseur d’électricité.

10. Ne déposez rien sur le cordon d’alimentation. Installez cet

appareil dans un endroit sécuritaire, là où personne ne

pourra trébucher sur la ligne d’alimentation ni le cordon

téléphonique modulaire.

11. N’insérez jamais d’objets à travers les fentes et ouvertures

de cet appareil, car ils pourraient toucher à des points

de tension dangereux ou court-circuiter des pièces, ce

qui constituerait un risque d’incendie ou d’électrocution.

N’échappez pas de liquides dans l’appareil.

12. Aﬁn de réduire les risques d’électrocution, ne démontez

pas l’appareil, mais apportez-le plutôt à un centre de service

qualiﬁé s’il doit être réparé. En enlevant le couvercle,

vous vous exposez à des tensions dangereuses ou autres

dangers similaires. Un remontage inadéquat peut être à

l’origine d’une électrocution lors d’une utilisation ultérieure

de l’appareil. Débranchez l’appareil avant de procéder au

nettoyage. Utilisez un chiffon humide et doux.

13. Ne surchargez pas les prises de courant et les rallonges.

14. Débranchez cet appareil de la prise de courant et

communiquez avec le département de service à la clientèle

de VTech dans les cas suivants :

• Lorsque le cordon d’alimentation est endommagé ou

écorché.

• Si du liquide a été échappé dans l’appareil.

• Si l’appareil a été exposé à une source d’humidité telle

que la pluie ou l’eau.

• Si le produit ne fonctionne pas normalement en

respectant les instructions de fonctionnement. Réglez

uniquement les commandes indiquées dans le les

instructions de fonctionnement. Les réglages incorrects

des autres commandes pourraient provoquer un

dommage qui pourrait exiger un travail exhaustif

de la part d’un technicien autorisé aﬁn de rétablir le

fonctionnement normal de l’appareil.

• Si le produit a été échappé et que le socle et/ou le

combiné a été endommagé.

• Si le produit afﬁche une nette diminution de sa

performance.

15. Évitez d’utiliser un téléphone (autre qu’un sans ﬁl) pendant

un orage. Les éclairs peuvent être à l’origine d’une

électrocution.

16. N’utilisez pas le téléphone pour rapporter une fuite de

gaz à proximité de la fuite. En certaines circonstances, une

ﬂammèche pourrait être provoquée lorsque l’adaptateur

est branché à une prise de courant, ou lorsque le combiné

est déposé sur le socle. Ceci est un événement commun

associé à la fermeture d’un circuit électrique. L’utilisateur

ne devrait pas brancher le téléphone à une prise de

courant, et ne devrait pas déposer le combiné chargé sur

le socle, si le téléphone se trouve à proximité d’un endroit

comportant des concentrations de gaz inﬂammables, à

moins que la ventilation soit adéquate. Une ﬂammèche

dans un tel endroit pourrait provoquer un incendie ou une

explosion. De tels environnements peuvent comprendre:

des endroits où l’on utilise de l’oxygène médical sans

ventilation adéquate; des gaz industriels (dissolvants de

nettoyage, des vapeurs d’essence, etc.); une fuite de gaz

naturel, etc.

17. Ne placez que le combiné de votre téléphone près de votre

oreille lorsqu’en mode de conversation.

18. Ces adaptateurs ont été conçus pour être orientés en

position verticale ou montés au sol. Les broches ne sont

pas conçues pour maintenir l’adaptateur en place si celui-ci

est barnché dans une prise au plafond ou sous une table/

armoire.

19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le

socle de prise de courant doit etre installe a proximite du

materiel et doit etre aisement accessible.

20. MISE EN GARDE: Il peut y avoir un risque

d’explosion si vous utilisez le mauvais type de piles pour le

téléphone. N’utilisez que les piles rechargeable inclus ou les

piles de rechange. N’incinérez pas les piles. Celles-ci

risqueraient d’exploser. Mettre au rebut les batteries

usagées conformément aux instructions du fabricant.

Débrancher les lignes téléphoniques avant le

remplacement des piles.

• Évite d’utiliser la batterie dans les conditions suivantes:

• des températures extrêmes faibles ou élevées

auxquelles une batterie peut être soumise pendant

l’utilisation, le stockage ou le transport.

• remplacement d’une batterie par un type incorrect

pouvant supprimer une protection.

• mise au rebut d’une batterie dans un feu ou dans un

four chaud, ou écrasement mécanique ou coupure

d’une batterie, susceptible de provoquer une

explosion.

• maintien d’une batterie dans un environnement

à très haute température pouvant provoquer

une explosion ou la fuite de liquide ou de gaz

inﬂammables.

• batterie soumise à une pression de l’air

extrêmement faible pouvant provoquer une

explosion ou la fuite de liquide ou de gaz

inﬂammables.

21. N’utilisez que les adaptateurs inclus avec ce produit.

L’utilisation d’un adaptateur dont la polarité ou la tension

serait inadéquate risque d’endommager sérieusement le

produit et mettre votre sécurité en péril.

22. La plaque signalétique appliquée est située au bas ou à

proximité du produit.

CONSERVEZ CES INSTRUCTIONS

Pile

• N’utilisez que la pile incluse ou l’équivalent.

• Ne jetez pas la pile au feu. Vériﬁez les instructions

spéciﬁques de mise aux rebus auprès des autorités locales.

• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en

échapperait est corrosif et pourrait causer des brûlures ou

des blessures aux yeux ou à la peau. L’électrolyte est toxique

si avalé.

• Soyez prudents lorsque vous manipulez les piles aﬁn

d’éviter les courts-circuits provoqués par des matériaux

conducteurs.

• Rechargez la pile incluse avec cet appareil, selon les

instructions et limites spéciﬁées dans ce guide d’utilisation.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (s’applique uniquement aux

téléphones numériques sans ﬁl) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une

ﬁrme de recherche indépendante, a mené une évaluation

pluridisciplinaire des interférences entre les téléphones sans

ﬁl portatifs et les stimulateurs cardiaques implantés dans

l’organisme. Appuyée par l’Administration des aliments et

drogues (FDA) des États-Unis, la ﬁrme WTR recommande aux

médecins :

Avis aux détenteurs de stimulateurs cardiaques

• Ils doivent tenir le téléphone sans ﬁl à une distance d’au

moins six pouces du stimulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl directement

sur le stimulateur cardiaque, tel que dans une poche de

chemise, lorsque celui-ci est en marche.

• Ils doivent utiliser le téléphone sans ﬁl en l’appuyant

sur l’oreille qui se trouve dans la direction opposée au

stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé de

risque pour les détenteurs de simulateurs cardiaques causés

par les gens qui utilisent un téléphone sans ﬁl à proximité de

ceux-ci.

À propos des téléphones sans ﬁl

Conﬁdentialité : Les mêmes caractéristiques qui constituent

des avantages pour les téléphones sans ﬁl afﬁchent également

des restrictions. Les appels téléphoniques sont transmis entre

le combiné sans ﬁl et le socle par le biais d’ondes radio ; il y a

donc la possibilité que vos conversations téléphoniques sans ﬁl

soient interceptées par des équipements de réception radio se

trouvant dans la portée du combiné sans ﬁl. Pour cette raison,

vous ne devez pas percevoir les communications téléphoniques

sans ﬁl comme étant aussi conﬁdentielles que celles des

téléphones à cordons.

Alimentation électrique : Le socle de ce téléphone sans ﬁl

doit être branché à une prise électrique fonctionnelle. La prise

électrique ne doit pas être contrôlée par un interrupteur mural.

Les appels ne pourront pas être effectués du combiné sans ﬁl

si le socle est débranché ou mis hors tension ou si le courant est

coupé.

Possibilité d’interférences aux téléviseurs : Certains téléphones

sans ﬁl fonctionnent sur des fréquences pouvant causer

des interférences aux téléviseurs et aux magnétoscopes.

Pour réduire ou prévenir de telles interférences, ne placez

pas le socle du téléphone sans ﬁl près ou sur un téléviseur

ou magnétoscope. S’il y a présence de parasites, il est

conseillé d’éloigner le téléphone sans ﬁl du téléviseur ou du

magnétoscope aﬁn de réduire possiblement les interférences.

Piles rechargeables : Manipulez les piles avec soin aﬁn de ne

pas les court-circuiter avec des bagues, bracelets ou clés. Les

piles ou le conducteur peut surchauffer et causer des blessures.

Respectez la polarité adéquate entre la pile et le chargeur.

Les bloc-piles rechargeables à l’hydrure métallique de nickel :

Jetez ces blocs-piles de manière écologique et sécuritaire. Ne

les incinérez pas et ne les percez pas. Tel que les autres piles de

ce type, elles pourraient dégager une matière toxique qui peut

causer

des blessures corporelles si elles sont brûlées ou percées.

The RBRC SEAL

The RBRC seal on the nickel-metal hydride

battery indicates that VTech Communications,

Inc. is voluntarily participating in an industry

program to collect and recycle these batteries at

the end of their useful lives, when taken out of

service within the United States and Canada.

The program provides a convenient alternative

to placing used nickel-metal hydride batteries into the trash or

municipal waste, which may be illegal in your area.

VTech’s participation makes it easy for you to drop off the spent

battery at local retailers participating in the RBRC program or at

authorized VTech product service centers. Please call

1 (800) 8 BATTERY® for information on Ni-MH battery recycling

and disposal bans/restrictions in your area. VTech’s involvement

in this program is part of its commitment to protecting our

environment and conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks

of Call2recycle, Inc.

FCC, ACTA and IC regulations

FCC Part 15

NOTE: This equipment has been tested and found to comply

with the requirements for a Class B digital device under Part 15

of the Federal Communications Commission (FCC) rules. These

requirements are intended to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

WARNING: Changes or modiﬁcations to this equipment not

expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation. Privacy of communications may not be

ensured when using this telephone.

To ensure safety of users, the FCC has established criteria for the

amount of radio frequency energy that can be safely absorbed

by a user or bystander according to the intended usage of the

product. This product has been tested and found to comply

with the FCC criteria. The handset may be safely held against

the ear of the user. The telephone base shall be installed and

used such that parts of the user’s body other than the hands are

maintained at a distance of approximately 20 cm (8 inches) or

more.

This Class B digital apparatus complies with Canadian

requirement:

CAN ICES-3 (B)/NMB-3(B).

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and

with technical requirements adopted by the Administrative

Council for Terminal Attachments (ACTA). The label on the back

or bottom of this equipment contains, among other things,

a product identiﬁer in the format US:AAAEQ##TXXXX. This

identiﬁer must be provided to your telephone service provider

upon request.

The plug and jack used to connect this equipment to premises

wiring and the telephone network must comply with applicable

Part 68 rules and technical requirements adopted by ACTA. A

compliant telephone cord and modular plug is provided with

this product. It is designed to be connected to a compatible

modular jack that is also compliant. An RJ11 jack should normally

be used for connecting to a single line and an RJ14 jack for two

lines. See the installation instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used to determine

how many devices you may connect to your telephone line

and still have them ring when you are called. The REN for this

product is encoded as the 6th and 7th characters following the

US: in the product identiﬁer (e.g., if ## is 03, the REN is 0.3). In

most, but not all areas, the sum of all RENs should be ﬁve (5.0)

or less. For more information, please contact your telephone

service provider.

This equipment must not be used with Party Lines. If you have

specially wired alarm dialing equipment connected to your

telephone line, ensure the connection of this equipment does

not disable your alarm equipment. If you have questions about

what will disable alarm equipment, consult your telephone

service provider or a qualiﬁed installer.

If this equipment is malfunctioning, it must be unplugged

from the modular jack until the problem has been corrected.

Replacement to this telephone equipment can only be made

by the manufacturer or its authorized agents. For replacement

procedures, follow the instructions outlined under the Limited

warranty.

If this equipment is causing harm to the telephone network,

the telephone service provider may temporarily discontinue

your telephone service. The telephone service provider is

required to notify you before interrupting service. If advance

notice is not practical, you will be notiﬁed as soon as possible.

You will be given the opportunity to correct the problem and

the telephone service provider is required to inform you of

your right to ﬁle a complaint with the FCC. Your telephone

service provider may make changes in its facilities, equipment,

operation, or procedures that could affect the proper

functioning of this product. The telephone service provider is

required to notify you if such changes are planned.

If this product is equipped with a corded or cordless handset, it

is hearing aid compatible.

If this product has memory dialing locations, you may choose to

store emergency telephone numbers (e.g., police, ﬁre, medical)

in these locations. If you do store or test emergency numbers,

please:

Remain on the line and brieﬂy explain the reason for the call

before hanging up.

Perform such activities in off-peak hours, such as early morning

or late evening.

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s)

that comply with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s). Operation is

subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including

interference that may cause undesired operation of the device.

Privacy of communications may not be ensured when using this

telephone.

The term ‘’IC:‘’ before the certiﬁcation/registration number only

signiﬁes that the Industry Canada technical speciﬁcations were

met.

The Ringer Equivalence Number (REN) for this terminal

equipment is 1.0. The REN indicates the maximum number of

devices allowed to be connected to a telephone interface. The

termination of an interface may consist of any combination of

devices subject only to the requirement that the sum of the

RENs of all the devices not exceed ﬁve.

This product meets the applicable Innovation, Science and

Economic Development Canada technical speciﬁcations.

California energy commission

battery charging testing

instructions

This telephone is set up to comply with the energy-conserving

standards right out of the box. These instructions are intended for

California Energy Commission (CEC) compliance testing only. When

the CEC battery charging testing mode is activated, all telephone

functions, except battery charging, will be disabled.

To activate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power

outlet. Make sure all handsets are plugged with charged

batteries before proceeding.

2. While you press and hold FIND HANDSET, plug the

telephone base power adapter back to the power outlet.

3. After about 20 seconds, when the IN USE light starts ﬂashing,

release FIND HANDSET and then press it again within 2

seconds.

When the phone successfully enters the CEC battery charging

testing mode, the IN USE light turns off and all handsets

display 1.PRESS FIND HS ON BASE 4 SEC and 2.THEN PRESS #

ON HANDSET alternately.

When the phone fails to enter this mode, repeat Step 1 through

Step 3 above.

To deactivate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power

outlet, and then plug it back in. Then the telephone base is

powered up as normal.

2. Place the handset in the telephone base to register it back. It

displays Registering...

The handset show Registered and you hear a beep when the

registration process completes. The registration process takes

about 90 seconds to complete.

Limited Warranty

What does this limited warranty cover?

The manufacturer of this VTech product, VTech Communications,

Inc. (“VTech”), warrants to the holder of a valid proof of purchase

(“Consumer” or “you”) that the Product and all accessories

provided by VTech in sales package (“Product”) are free from

material defects in material and workmanship, pursuant to

the following terms and conditions, when installed and used

normally and in accordance with operating instructions. This

limited warranty extends only to the Consumer for Products

purchased and used in the United States of America and Canada.

What will VTech Communications do if the Product is not free

from material defects in materials and workmanship during the

limited warranty period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service

representative will replace at VTech’s option, without charge,

a Materially Defective Product. If we choose to replace the

Product, we may replace it with a new or refurbished Product

of the same or similar design. VTech will return replacement

products to you in working condition. VTech will retain defective

parts, modules, or equipment. Replacement of the Product, at

VTech’s option, is your exclusive remedy. You should expect the

replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the product extends for ONE (1)

YEAR from date of purchase (90 days on products purchased as

Refurbished*). This limited warranty also applies to replacement

Products for a period of either (a) 90 days from the date the

replacement Product is shipped to you or (b) the time remaining

on the original one-year limited warranty (90-day limited

warranty on products that are purchased as Refurbished*),

whichever is longer.

*Refurbished products purchased from our online store carry a

90-day replacement warranty.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident,

shipping or other physical damage, improper installation,

abnormal operation or handling, neglect, inundation, ﬁre,

water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration or

modiﬁcation by anyone other than an authorized service

representative of VTech; or

3. Product to the extent that the problem experienced is

caused by signal conditions, network reliability or cable or

antenna systems; or

4. Product to the extent that the problem is caused by use

with non-VTech electrical accessories; or

5. Product whose warranty/quality stickers, Product serial

number plates or electronic serial numbers have been

removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair

from outside the United States, or used for commercial

or institutional purposes (including but not limited to

Products used for rental purposes); or

7. Product returned without valid proof of purchase (see 2

below); or

8. Charges for installation or set up, adjustment of customer

controls, and installation or repair of systems outside the

unit.

How do you get warranty service?

To obtain warranty service in the United States of America, please

visit our website at www.vtechphones.com or call

1 (800) 595-9511 for instructions regarding where to return the

Product. In Canada, go to phones.vtechcanada.com or dial

1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s manual

- a check of the Product’s controls and features may save you a

service call.

Except as provided by applicable law, you assume the risk of loss

or damage during transit and transportation and are responsible

for delivery or handling charges incurred in the transport of

Product(s) to the service location. VTech will return replaced

product under this limited warranty to you, transportation,

delivery or handling charges prepaid. VTech assumes no risk for

damage or loss of the Product in transit.

What must you return with the Product to get warranty service?

1. Return the entire original package and contents including

the Product to the VTech service location along with a

description of the malfunction or difﬁculty;

2. Include “valid proof of purchase” (sales receipt) identifying

the Product purchased (Product model) and the date of

purchase or receipt; and

3. Provide your name, complete and correct mailing address,

and telephone number.

Other limitations

This warranty is the complete and exclusive agreement

between you and VTech. It supersedes all other written or oral

communications related to this product. VTech provides no other

warranties for this product. The warranty exclusively describes all

of VTech’s responsibilities regarding the product.

There are no other expressed warranties. No one is authorized to

make modiﬁcations to this warranty and you should not rely on

any such modiﬁcation.

State Law Rights: This warranty gives you speciﬁc legal rights,

and you may also have other rights which vary from state to state.

Limitations: Implied warranties, including those of ﬁtness for a

particular purpose and merchantability (an unwritten warranty

that the product is ﬁt for ordinary use) are limited to one year

from date of purchase. Some states do not allow limitations on

how long an implied warranty lasts, so the above limitation may

not apply to you.

In no event shall VTech be liable for any indirect, special,

incidental, consequential, or similar damages (including, but not

limited to lost proﬁts or revenue, inability to use the product, or

other associated equipment, the cost of substitute equipment,

and claims by third parties) resulting from the use of this product.

Some states do not allow the exclusion or limitation of incidental

or consequential damages, so the above limitation or exclusion

may not apply to you.

Please retain your original sales receipt as proof of purchase

Disclaimer and Limitation of

Liability

VTech Communications, Inc. and its suppliers assume no

responsibility for any damage or loss resulting from the use of

this user’s manual. VTech Communications, Inc. and its suppliers

assume no responsibility for any loss or claims by third parties

that may arise through the use of this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR

97223, United States

Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada

Technical speciﬁcations

Frequency

control

Crystal controlled PLL synthesizer

Transmit

frequency

Handset: 1921.536-1928.448 MHz

Telephone Base: 1921.536-1928.448 MHz

Channels DECT channel: 5

Nominal

effective

range

Maximum power allowed by FCC and

IC. Actual operating range may vary

according to environmental conditions

at the time of use.

Power

requirement

Handset: 2.4V Ni-MH battery

Telephone base: 6V DC @ 0.4A

Charger: 6V DC @ 0.4A

Memory Directory: 50 memory locations;

up to 30 digits and 15 characters

Caller ID log: 50 memory locations;

up to 24 digits and 15 characters

Telephones identiﬁed with this logo have

reduced noise and interference when

used with most T-coil equipped hearing

aids and cochlear implants. The TIA-1083

Compliant Logo is a trademark of the

Telecommunications Industry Association.

Used under license.

Compatible with

Hearing Aid T-Coil

TIA-1083

Turn on or off the call screening

Use this feature to choose whether incoming

messages can be heard over the telephone base

when they are being recorded. If you turn call

screening on, you hear the incoming message.

1. Press MENU when the handset is not in use.

2. Press q or p to choose Answering sys and then

press SELECT.

3. Press q or p to choose Ans sys setup and then

press SELECT.

4. Press SELECT again to choose Call screening.

5. Press q or p to choose Screening:On or

Screening:Off, then press SELECT to save.

Screen a call with answering system

Screen calls at the cordless handset:

If the answering system is on and a call is being

answered by the answering system, the handset

shows To screen call, press [SELECT].

Press SELECT to screen the call on your handset.

The handset shows Screening....

Option while a message is being recorded

• Press q/VOLUME or p/VOLUME on the

handset to adjust the call screening volume.

Screen calls at the base:

If the answering system and call screening are on,

the announcement and the incoming message

broadcast at the telephone base when a call is

answered by the answering system.

Option while a message is being recorded

• Press qVOL - or pVOL + on the telephone base

to adjust the call screening volume.

• Press /PLAY to temporarily turn on the

screening if the call screening is set to off.

Retrieve voicemail from

telephone service

Voicemail is a feature available from most

telephone service providers. It may be included

with your telephone service, or may be optional.

Fees may apply.

Retrieve voicemail

When you received a voicemail, the handset

displays and New voicemail. To retrieve, you

typically dial an access number provided by your

telephone service provider, and then enter a security

code. Contact your telephone service provider

for instructions on how to conﬁgure the voicemail

settings and listen to messages.

NOTE: After you have listened to all new

voicemail messages, the indicators on the

handset turn off automatically.

Set your voicemail number

You can save your access number on each handset

for easy access to your voicemail.

After you saved the voicemail number, you can

press and hold to retrieve voicemail.

1. Press MENU when the phone is not in use.

2. Scroll to Settings and then press SELECT.

3. Scroll to Voicemail # and then press SELECT.

4. Use the dialing keys to enter the voicemail

number (up to 30 digits).

5. Press SELECT to save.

Clear the new voicemail indicators

If you have retrieved your voicemail while away from

home, and the handset still displays the new voicemail

indicators, use this feature to turn off the indicators.

NOTE: This feature turns off the indicators

only, it does not delete your voicemail

messages.

1. Press MENU when the phone is not in use.

2. Scroll to Settings and then press SELECT.

3. Scroll to Clr voicemail and then press SELECT.

4. Press SELECT again to conﬁrm. You hear a

conﬁrmation tone.

ECO mode

This power conserving technology reduces power

consumption for optimal battery performance. The

ECO mode activates automatically whenever the

handset is synchronized with the telephone base.

General product care

Taking care of your telephone

Your cordless telephone contains sophisticated

electronic parts, so it must be treated with care.

Avoid rough treatment

Place the handset down gently. Save the original

packing materials to protect your telephone if you

ever need to ship it.

Avoid water

Your telephone can be damaged if it gets wet. Do

not use the handset outdoors in the rain, or handle

it with wet hands. Do not install the telephone base

near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power

surges harmful to electronic equipment. For your

own safety, take caution when using electrical

appliances during storms.

Cleaning your telephone

Your telephone has a durable plastic casing that

should retain its luster for many years. Clean it

only with a dry non-abrasive cloth. Do not use

dampened cloth or cleaning solvents of any kind.

Need help?

For operations and guides to help you using your

telephone, and for the latest information and

supports, go and check the online help topics and

online FAQs.

Use your smartphone or mobile device to access our

online help.

• Go to https://help.vtechphones.com/cs6529 (US);

OR https://phones.vtechcanada.com/en/support/

general/manuals?model=cs6529 (Canada)

• Scan the QR code on the right.

Launch the camera app or QR code

scanner app on your smartphone or

tablet. Hold the device’s camera up

to the QR code and frame it. Tap the

notiﬁcation to trigger the redirection

of the online help.

- If the QR code is not clearly

displayed, adjust your camera’s focus

by moving your device closer or

further away until it is clear.

You can also call our Customer

Support at 1 (800) 595-9511 [in US] or

1 (800) 267-7377 [in Canada] for help.

Recycle this product

when you are done

with it

Scan the QR code on the right or visit

www.vtechphones.com/recycle.

(For the US only)

CS6529 (US)

CS6529 (CA)

VTech CS6529-3 Manuel utilisateur

Marque: VTech

Modèle: CS6529-3

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: VTech CS6529-3 User manual

Documents connexes

Autres documents

AT&T DL72539 Guide de démarrage rapide