Makita UH004G Manuel utilisateur

Marque: Makita

Modèle: UH004G

Catégorie: Taille-haies électriques

Taper: Manuel utilisateur

INSTRUCTION MANUAL

MANUEL D'INSTRUCTION

MANUAL DE INSTRUCCIONES

Cordless Hedge Trimmer

Taille-haie sans l

Cortasetos Inalámbrico

UH004G

UH005G

UH006G

UH007G

UH008G

UH009G

IMPORTANT: Read Before Using.

IMPORTANT : Lire avant usage.

IMPORTANTE: Lea antes de usar.

2ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: UH004G UH005G UH006G

Blade length 600 mm (23-5/8") 750 mm (29-1/2") 600 mm (23-5/8")

Strokes per minute 2,000 / 3,600 / 5,000 /min 2,000 / 3,000 /

4,000 /min

Overall length 1,120 mm (44") 1,263 mm (49-3/4") 1,123 mm (44-1/4")

Rated voltage D.C. 36 V - 40 V max

Net weight 4.3 - 4.9 kg

(9.5 - 10.8 lbs)

4.5 - 5.1 kg

(9.9 - 11.2 lbs)

4.4 - 5.0 kg

(9.7 - 11.0 lbs)

Model: UH007G UH008G UH009G

Blade length 750 mm (29-1/2") 600 mm (23-5/8") 750 mm (29-1/2")

Strokes per minute 2,000 / 3,000 /

4,000 /min

2,000 / 3,600 / 5,000 /min

Overall length 1,274 mm (50-1/4") 1,120 mm (44") 1,262 mm (49-3/4")

Rated voltage D.C. 36 V - 40 V max

Net weight 4.6 - 5.2 kg

(10.1 - 11.5 lbs)

4.3 - 4.9 kg

(9.5 - 10.8 lbs)

4.4 - 5.0 kg

(9.7 - 11.0 lbs)

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsmaydierfromcountrytocountry.

• Theweightmaydierdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-

est combination, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Batterycartridge BL4025 / BL4040

Charger DC40RA

• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof

residence.

WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges

andchargersmaycauseinjuryand/orre.

Recommended portable power pack

Portable power pack PDC1200 / PDC01

• Theportablepowerpack(s)listedabovemaynotbeavailabledependingonyourregionofresidence.

• Beforeusingtheportablepowerpack,readinstructionandcautionarymarkingsontheportablepowerpack.

3ENGLISH

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listedbelowmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

Theterm"powertool"inthewarningsreferstoyour

mains-operated(corded)powertoolorbattery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

whichmayignitethedustorfumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

youtolosecontrol.

Electrical Safety

Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodiedplugsand

matching outlets will reduce risk of electric shock.

2. Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tricshockifyourbodyisearthedorgrounded.

3. Do not expose power tools to rain or wet con-

ditions. Water entering a power tool will increase

the risk of electric shock.

4. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

6. If operating a power tool in a damp location is

unavoidable, use a ground fault circuit inter-

rupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electric shock.

Power tools can produce electromagnetic elds

(EMF) that are not harmful to the user. However,

users of pacemakers and other similar medical

devices should contact the maker of their device and/

or doctor for advice before operating this power tool.

Personal Safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inuence of drugs, alcohol or med-

ication. A moment of inattention while operating

powertoolsmayresultinseriouspersonalinjury.

2. Use personal protective equipment. Always

wear eye protection. Protective equipment such

asdustmask,non-skidsafetyshoes,hardhat,or

hearing protection used for appropriate conditions

willreducepersonalinjuries.

3. Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to power source and/or battery pack, picking

up or carrying the tool.Carryingpowertoolswith

yourngerontheswitchorenergisingpowertools

that have the switch on invites accidents.

4. Remove any adjusting key or wrench before

turning the power tool on.Awrenchorakeyleft

attachedtoarotatingpartofthepowertoolmay

resultinpersonalinjury.

5. Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts.Looseclothes,jewel-

leryorlonghaircanbecaughtinmovingparts.

7. If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

8. Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action

cancausesevereinjurywithinafractionofa

second.

Always wear protective goggles to protect your

eyes from injury when using power tools. The

goggles must comply with ANSI Z87.1 in the USA.

It is an employer's responsibility to enforce the

use of appropriate safety protective equipment

by the tool operators and by other persons in

the immediate working area.

Power tool use and care

1. Do not force the power tool. Use the correct

power tool for your application. The correct

powertoolwilldothejobbetterandsaferatthe

rate for which it was designed.

2. Do not use the power tool if the switch does

not turn it on and o.Anypowertoolthatcannot

be controlled with the switch is dangerous and

must be repaired.

3. Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any adjust-

ments, changing accessories, or storing power

tools.Suchpreventivesafetymeasuresreduce

theriskofstartingthepowertoolaccidentally.

4. Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

5. Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition that

may aect the power tool’s operation. If dam-

aged, have the power tool repaired before use.

Manyaccidentsarecausedbypoorlymaintained

power tools.

4ENGLISH

6. Keep cutting tools sharp and clean.Properly

maintained cutting tools with sharp cutting edges

arelesslikelytobindandareeasiertocontrol.

7. Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

foroperationsdierentfromthoseintendedcould

result in a hazardous situation.

8. Keep handles and grasping surfaces dry,

clean and free from oil and grease.Slippery

handles and grasping surfaces do not allow for

safe handling and control of the tool in unexpected

situations.

9. When using the tool, do not wear cloth work

gloves which may be entangled. The entangle-

mentofclothworkglovesinthemovingpartsmay

resultinpersonalinjury.

Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer. A charger that is suitable for

onetypeofbatterypackmaycreateariskofre

whenusedwithanotherbatterypack.

2. Use power tools only with specically desig-

nated battery packs.Useofanyotherbattery

packsmaycreateariskofinjuryandre.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another.Shortingthebatterytermi-

nalstogethermaycauseburnsorare.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical

help.Liquidejectedfromthebatterymaycause

irritation or burns.

5. Do not use a battery pack or tool that is dam-

aged or modied.Damagedormodiedbatteries

mayexhibitunpredictablebehaviourresultingin

re,explosionorriskofinjury.

6. Do not expose a battery pack or tool to re or

excessive temperature.Exposuretoreortem-

peratureabove130°Cmaycauseexplosion.

7. Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specied in the instruc-

tions.Chargingimproperlyorattemperatures

outsidethespeciedrangemaydamagethe

batteryandincreasetheriskofre.

Service

1. Have your power tool serviced by a qualied

repair person using only identical replacement

parts.Thiswillensurethatthesafetyofthepower

tool is maintained.

2. Never service damaged battery packs. Service

ofbatterypacksshouldonlybeperformedbythe

manufacturer or authorized service providers.

3. Follow instruction for lubricating and chang-

ing accessories.

4. Do not modify or attempt to repair the appli-

ance or the battery pack except as indicated in

the instructions for use and care.

Cordless Hedge Trimmer Safety

Warnings

1. Keep all parts of the body away from the blade.

Do not remove cut material or hold material

to be cut when blades are moving. Blades

continuetomoveaftertheswitchisturnedo.A

moment of inattention while operating the hedge

trimmermayresultinseriouspersonalinjury.

2. Carry the hedge trimmer by the handle with the

blade stopped and taking care not to operate

any power switch.Propercarryingofthehedge

trimmer will decrease the risk of inadvertent start-

ingandresultantpersonalinjuryfromtheblades.

3. When transporting or storing the hedge trim-

mer, always t the blade cover. Proper handling

of the hedge trimmer will decrease the risk of

personalinjuryfromtheblades.

4. When clearing jammed material or servicing

the unit, make sure all power switches are o

and the battery pack is removed or discon-

nected. Unexpected actuation of the hedge trim-

merwhileclearingjammedmaterialorservicing

mayresultinseriouspersonalinjury.

Hold the hedge trimmer by insulated gripping

surfaces only, because the blade may contact

hidden wiring.Bladescontactinga"live"wiremay

make exposed metal parts of the hedge trimmer

"live" and could give the operator an electric shock.

6. Keep all power cords and cables away from

cutting area.Powercordsorcablesmaybehid-

deninhedgesorbushesandcanbeaccidentally

cutbytheblade.

Do not use the hedge trimmer in bad weather con-

ditions, especially when there is a risk of lightning.

Thisdecreasestheriskofbeingstruckbylightning.

Additional Safety Instructions

Preparation

1. Check the hedges and bushes for foreign

objects, such as wire fences or hidden wiring

before operating the tool.

2. The tool must not be used by children or

young persons under 18 years of age. Young

personsover16yearsofagemaybeexempted

fromthisrestrictioniftheyareundergoingtraining

under the supervision of an expert.

3. First-time users should have an experienced

user show them how to use the tool.

Use the tool only if you are in good physical

condition.Ifyouaretired,yourattentionwillbe

reduced.Beespeciallycarefulattheendofawork-

ingday.Performallworkcalmlyandcarefully.The

user is responsible for all damages to third parties.

5. Never use the tool when under the inuence of

alcohol, drugs or medication.

6. Work gloves of stout leather are part of the

basic equipment of the tool and must always

be worn when working with it. Also wear

sturdy shoes with anti-skid soles.

7. Before starting work check to make sure that

the tool is in good and safe working order.

Ensure guards are tted properly. The tool

must not be used unless fully assembled.

5ENGLISH

Operation

1. Hold the tool rmly with both hands when

using the tool.

2. The tool is intended to be used by the operator

at ground level. Do not use the tool on ladders

or any other unstable support.

3. DANGER - Keep hands away from blade.

Contact with blade will result in serious personal

injury.

4. Make sure you have a secure footing before

starting operation.

5. Do not operate the tool at no-load

unnecessarily.

6. Immediately switch o the tool and remove the

battery cartridge if the shear blades should

come into contact with a fence or other hard

object. Check the blades for damage, and if

damaged, replace the blades immediately.

7. Before checking the shear blades, taking care

of faults, or removing material caught in the

shear blades, always switch o the tool and

remove the battery cartridge.

Never point the shear blades to yourself or others.

9. If the blades stop moving due to the stuck of

foreign objects between the blades during

operation, switch o the tool and remove the

battery cartridge, and then remove the foreign

objects using tools such as pliers. Removing

theforeignobjectsbyhandmaycauseaninjury

forthereasonthatthebladesmaymoveinreac-

tiontoremovingtheforeignobjects.

10. Avoid dangerous environment. Don't use the

tool in damp or wet locations or expose it to

rain. Water entering the tool will increase the

risk of electric shock.

11. When you use the tool on muddy ground, wet

slope, or slippery place, pay attention to your

footing.

12. Avoid working in poor environment where

increased user fatigue is expected.

13. Do not use the tool in bad weather where visi-

bility is limited.Failuretodosomaycausefallor

incorrectoperationduetolowvisibility.

14. Do not submerge the tool into a puddle.

15. Do not leave the tool unattended outdoors in

the rain.

16. When wet leaves or dirt adhere to the suc-

tion mouth (ventilation window) due to rain,

remove them.

17. Do not use the tool in the snow.

Electrical and battery safety

1. Avoid dangerous environment. Don't use the

tool in dump or wet locations or expose it to

rain. Water entering the tool will increase the risk

of electric shock.

2. Do not dispose of the battery(ies) in a re.

Thecellmayexplode.Checkwithlocalcodesfor

possible special disposal instructions.

Do not open or mutilate the battery(ies). Released

electrolyteiscorrosiveandmaycausedamagetothe

eyesorskin.Itmaybetoxicifswallowed.

4. Do not charge battery in rain, or in wet

locations.

5. Do not charge the battery outdoors.

6. Do not handle charger, including charger plug,

and charger terminals with wet hands.

7. Do not replace the battery with wet hands.

8. Do not replace the battery in the rain.

9. Do not wet the terminal of battery with liquid

such as water, or submerge the battery. Do not

leave the battery in the rain, nor charge, use,

or store the battery in a damp or wet place. If

the terminal gets wet or liquid enters inside of bat-

tery,thebatterymaybeshortcircuitedandthereis

ariskofoverheat,re,orexplosion.

10. After removing the battery from the tool or

charger, be sure to attach the battery cover to

the battery and store it in a dry place.

11. If the battery cartridge gets wet, drain the

water inside and then wipe it with a dry cloth.

Dry the battery cartridge completely in a dry

place before use.

Maintenance and storage

1. Switch o the tool and remove the battery

cartridge before doing any maintenance work.

2. When moving the tool to another location,

including during work, always remove the

battery cartridge and put the blade cover on

the shear blades. Never carry or transport the

tool with the blades running. Never grasp the

blades with your hands.

3. Clean the tool and especially the shear blades

after use, and before putting the tool into stor-

age for extended periods. Lightly oil the blades

and put on the blade cover.

4. Store the tool with the blade cover on, in a dry

room. Keep it out of reach of children. Never

store the tool outdoors.

5. Do not dispose of the battery(ies) in a re. The

cell may explode. Check with local codes for

possible special disposal instructions.

6. Do not open or mutilate the battery(ies).

Released electrolyte is corrosive and may

cause damage to the eyes or skin. It may be

toxic if swallowed.

7. Do not wash the tool with high pressure water.

8. When washing the tool, do not let water enter

the electrical mechanism such as battery,

motor, and terminals.

9. Perform inspection or maintenance in a place

where rain can be avoided.

10. After using the tool, remove the adhered dirt

and dry the tool completely before storing.

Depending on the season or the area, there is a

risk of malfunction due to freezing.

11. When storing the tool, avoid direct sunlight

and rain, and store it in a place where it does

not get hot or humid.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

6ENGLISH

WARNING:

Use of this product can create dust con-

taining chemicals which may cause respiratory or other ill-

nesses. Some examples of these chemicals are compounds

found in pesticides, insecticides, fertilizers and herbicides.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to lter out microscopic particles.

Symbols

Thefollowingsshowthesymbolsusedfortool.

volts

direct current

no load speed

revolutions or reciprocation per minute

Important safety instructions for

battery cartridge

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery char-

ger, (2) battery, and (3) product using battery.

Do not disassemble or tamper the battery cartridge.

Itmayresultinare,excessiveheat,orexplosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge.Suchconductmayresultina

re,excessiveheat,orexplosion.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

Forcommercialtransportse.g.bythirdparties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Pleasealsoobservepossiblymoredetailed

national regulations.

Tapeormaskoopencontactsandpackupthe

batteryinsuchamannerthatitcannotmove

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliantproductsmayresultinare,exces-

siveheat,explosion,orleakofelectrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge.Itmayresultinpoorperformanceor

breakdownofthetoolorbatterycartridge.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near a high-voltage elec-

trical power lines.Itmayresultinamalfunction

orbreakdownofthetoolorbatterycartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

havebeenaltered,mayresultinthebatterybursting

causingres,personalinjuryanddamage.Itwill

alsovoidtheMakitawarrantyfortheMakitatooland

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

7ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch o the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge.Failuretoholdthetoolandthebattery

cartridgermlymaycausethemtoslipoyourhands

andresultindamagetothetoolandbatterycartridge

andapersonalinjury.

►1. Red indicator 2. Button 3.Batterycartridge

Toremovethebatterycartridge,slideitfromthetool

while sliding the button on the front of the cartridge.

Toinstallthebatterycartridge,alignthetongueonthe

batterycartridgewiththegrooveinthehousingandslip

itintoplace.Insertitallthewayuntilitlocksinplace

withalittleclick.Ifyoucanseetheredindicatoras

showninthegure,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

youorsomeonearoundyou.

CAUTION: Do not install the battery cartridge

forcibly.Ifthecartridgedoesnotslideineasily,itis

notbeinginsertedcorrectly.

Indicating the remaining battery

capacity

Pressthecheckbuttononthebatterycartridgetoindi-

catetheremainingbatterycapacity.Theindicatorlamps

light up for a few seconds.

►1. Indicator lamps 2. Check button

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

Thebattery

mayhave

malfunctioned.

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydierslightly

fromtheactualcapacity.

NOTE:Therst(farleft)indicatorlampwillblinkwhen

thebatteryprotectionsystemworks.

8ENGLISH

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotection

system.Thissystemautomaticallycutsopowerto

themotortoextendtoolandbatterylife.Thetoolwill

automaticallystopduringoperationifthetoolisplaced

under one of the following conditions:

►1. Caution lamp

Caution lamp Status

Color On Blinking

Green Overload

Red (tool) / (battery) Overheat

Red Over

discharge

NOTICE: Depending on the usage conditions,

the tool automatically stops without any indica-

tion if the branches or debris are entangled in the

tool. In this case, switch o the tool and remove

the battery cartridge, and then remove entangled

branches or debris using tools such as pliers.

After removing the branches or debris, install the

battery cartridge and turn on the tool again.

Overload protection

Ifthetoolorbatteryisoverloadedbyentangled

branchesorotherdebris,thetoolautomaticallystops

and the caution lamp starts blinking in green.

Inthissituation,turnthetooloandstoptheapplication

that caused the tool to become overloaded. Then turn

the tool on to restart.

Overheat protection for tool or battery

Ifthetoolorbatterycartridgeisoverheated,thetool

stopsautomatically.Whenthetoolisoverheated,the

cautionlamplightsupinred.Whenthebatterycartridge

is overheated, the caution lamp blinks in red. Let the tool

and/orbatterycooldownbeforeturningthetoolonagain.

Overdischarge protection

Whenthebatterycapacitybecomeslow,thetoolstops

automaticallyandthecautionlampstartsblinkinginred.

If the tool does not operate even when the switches are

operated,removethebatterycartridgefromthetooland

charge it.

NOTICE: If the tool stops due to a cause

not described above, refer to the section for

troubleshooting.

Angle setting of the handle

CAUTION: Always make sure that the handle

is locked in the desired position before operation.

CAUTION: Do not pull down the lever to

unlock the handle while pulling the switch trigger.

Do not pull the switch trigger while pulling down

the lever and turning the handle. Failure to do so

maycauseamalfunctionofthetool.

You can set the angle of the handle to 0°, 45°, or 90°

to the left or right. To change the angle of the handle,

turn the handle while pulling down the lever, and then

release the lever.

►1. Lever

Power switch action

WARNING: For your safety, this tool is

equipped with lock-o lever which prevents the

tool from unintended starting. NEVER use the tool

if it runs when you simply press the switch lever

and pull the switch trigger without pressing the

lock-o lever. Return the tool to our authorized

service center for proper repairs BEFORE further

usage.

WARNING: NEVER tape down or defeat pur-

pose and function of lock-o lever.

WARNING: Before installing the battery car-

tridge on the tool, always check to see that the

switch trigger and switch lever actuate properly

and return to the "OFF" position when released.

Operating a tool with a switch that does not actuate

properlycanleadtolossofcontrolandseriousper-

sonalinjury.

9ENGLISH

CAUTION: Never put your nger on the

switch when carrying.Thetoolmaystartuninten-

tionallyandcauseinjury.

NOTICE: Do not pull the switch trigger hard with-

out pressing the lock-o lever. This can cause

switch breakage.

Press the main power button to turn on the tool. To turn

othetool,pressandholdthemainpowerbuttonuntil

thespeedindicatorsgoo.

►1. Main power button

NOTE: The caution lamp brinks if the switch trigger

is pulled under unoperatable conditions. The caution

lampblinksifyouturnonthemainpowerswitchwhile

holdingdownthelock-oleverandtheswitchtrigger.

NOTE:Thistoolemploystheautopower-ofunction.

To avoid unintentional start up, the main power switch

willautomaticallyshutdownwhentheswitchtrigger

is not pulled for a certain period after the main power

switch is turned on.

Topreventtheswitchtriggerfrombeingaccidentally

pulled,alock-oleverisprovided.Tostartthetool,

depressthelock-olever,andthenpresstheswitch

lever and pull the switch trigger. Release the switch

trigger to stop.

1 2

►1. Switch lever 2.Lock-olever3. Switch trigger

Speed adjusting

Youcanselectthetoolspeedbytappingthemain

powerbutton.Eachtimeyoutapthemainpowerbutton,

the level of speed will change.

►1. Speed indicator 2. Main power button

For UH004G/UH005G/UH008G/UH009G

Indicator Mode Stroke speed

High 5,000 /min

Medium 3,600 /min

Low 2,000 /min

For UH006G/UH007G

Indicator Mode Stroke speed

High 4,000 /min

Medium 3,000 /min

Low 2,000 /min

10 ENGLISH

Reverse button for debris removal

WARNING: If the entangled branches or

debris cannot be removed by the reverse func-

tion, switch o the tool and remove the bat-

tery cartridge, and then remove the entangled

branches or debris using tools such as pliers.

Failuretoswitchothetoolandremovethebat-

terycartridgemayresultinseriouspersonalinjury

from accidental start-up. Removing the entangled

branchesordebrisbyhandmaycauseaninjury,

sincetheshearbladesmaymoveinreactionto

removing them.

This tool has a reverse button to change the direction

ofshearbladesmovement.Itisonlyforremoving

branches and debris entangled in the tool.

To reverse the shear blades movement, tap the reverse

button when the shear blades have stopped, then press

the switch lever and pull the switch trigger while press-

ingthelock-olever.Thespeedindicatorsstartblink-

ing, and the shear blades move in reverse direction.

To return to regular movement, release the trigger and

wait until the shear blades stop.

►1. Speed indicator 2. Reverse button

NOTE: If the entangled branches or debris cannot be

removed,releaseandpulltheswitchtriggeruntilthey

are removed.

NOTE:Ifyoutapthereversebuttonwhiletheshear

blades are still moving, the tool comes to stop and to

bereadyforreversemovement.

Electronic function

Thetoolisequippedwiththeelectronicfunctionsforeasyoperation.

• Constant speed control

The speed control function provides the constant

rotation speed regardless of load conditions.

• Electric brake

This tool is equipped with an electric brake. If the

toolconsistentlyfailstoquicklystoptheshear

blades after releasing the switch trigger, have the

tool serviced at Makita Authorized Service Center.

• Accidental re-start preventive function

Evenifyouinstallthebatterycartridgewhilepull-

ing the switch trigger, the tool does not start. To

startthetool,rstreleasetheswitchtrigger,and

then pull the switch trigger.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before carrying out any work on the tool.

CAUTION: When replacing the shear blades,

always wear gloves so that your hands do not

directly contact the blades.

NOTICE: When replacing the shear blades, do

not wipe o grease from the gear and crank.

Installing or removing the shear

blades

CAUTION: Attach the blade cover before

removing or installing the shear blades.

You can install 600 mm (23-5/8") or 750 mm (29-1/2")

shearbladestoyourtool.

Place the tool upside down, and then remove 6 bolts.

►1. Bolt

2. Remove the cover and the plate.

►1. Cover 2. Plate

NOTE:Theplatemayremainonthecover.

11 ENGLISH

3. Remove the rod and the bearing.

►1. Rod 2. Bearing

NOTE:Therodmayremainonthecover.

4. Remove 2 bolts, the felt pad and the sleeves, and

then remove the shear blades.

►1. Felt pad 2. Bolt 3. Sleeve 4. Shear blades

5. Remove the blade cover.

6. Attach the blade cover to the new shear blades.

7. Adjustthecranksothat2holesarelinedupon

the alignment line.

►1. Hole 2. Alignment line

8. Aligntheprotrusionsontheshearbladesvertically

at the same position.

►1. Protrusion

9. Attach the felt pad to the shear blades.

►1. Felt pad

12 ENGLISH

10. Insert the protrusion on the shear blades to the

small hole on the rod, then align the position of the felt

pad with the holes on the tool, and then attach new

sleeves.

►1. Protrusion 2. Small hole 3. Sleeve 4. Felt pad

NOTICE: Apply a small amount of grease to the

inner periphery of the hole of the rod.

NOTICE: Be careful not to lose the sleeves.

11. Align the holes on the shear blades with the holes

onthetool,andthentighten2boltstoxtheshear

blades.

►1. Bolt 2. Hole

12. Attach the bearing and the rod.

►1. Rod 2. Small hole 3. Bearing

NOTICE: Apply a small amount of grease to the

inner periphery of the small hole of the rod.

NOTICE: Make sure that the protrusion on the

shear blades ts in the small hole on the rod.

13. Attach the plate.

►1. Protrusion 2. Plate

NOTICE: Make sure that the protrusion on the

shear blades ts in the hole on the plate.

14. Attach the cover, and then tighten 6 bolts.

►1. Bolt 2. Cover

13 ENGLISH

NOTICE: If the shear blades do not move

smoothly, the shear blades are not engaged with

the rods properly. Install the shear blades again.

NOTICE: If the parts other than the shear

blades such as the rods are worn out, ask Makita

Authorized Service Centers for parts replacement

or repairs.

Installing or removing the chip

receiver

Optional accessory

CAUTION: When installing or removing the

chip receiver, always wear gloves so that your

hands do not directly contact the shear blades.

NOTICE:

For UH004G/UH005G/UH006G/UH007G

The blade cover cannot be installed if the chip

receiver is installed on the tool. Before carrying

or storing the tool, uninstall the chip receiver,

and then install the blade cover to avoid blade

exposure.

NOTICE:

For UH004G/UH005G/UH006G/UH007G

Be sure to remove the blade cover before install-

ing the chip receiver.

The chip receiver gathers discarded leaves and makes

clean-up afterward much easier. It can be installed on

either side of the tool.

1. Hook the claws of the chip receiver to the shear

blades.

►1. Claw

2. Align the holes on the chip receiver with the

screws on the shear blades, and then attach the chip

receivertotheshearbladessecurely.

►1. Hole

NOTICE: Make sure that the chip receiver does

not overlap the branch catcher.

►1. Branch catcher

To remove the chip receiver, press the levers to release the claws.

►1. Lever

NOTICE: Never try to remove the chip receiver

by an excessive force with its hooks locked to the

shear blades.

14 ENGLISH

OPERATION

WARNING: Keep hands away from shear

blades.

CAUTION: Avoid operating the tool in very

hot weather as much as practicable. When operat-

ing the tool, be careful of your physical condition.

CAUTION: Be careful not to accidentally

contact a metal fence or other hard objects while

trimming.Theshearbladesmaybreakandcause

aninjury.

CAUTION: Be careful not to allow the shear

blades to contact the ground.Thetoolmayrecoil

andcauseaninjury.

CAUTION: Overreaching with a hedge trim-

mer, particularly from a ladder, is extremely

dangerous.Donotworkwhilestandingonanything

wobblyorinrm.

NOTICE: Do not attempt to cut branches thicker

than 10 mm (3/8") in diameter with the tool. Cut

branches to 10 cm (4") lower than the cutting height

using branch cutters before using the tool.

(1)

(2)

►(1) Cutting height (2) 10 cm (4")

NOTICE: Do not cut down dead trees or similar

hard objects.Doingsomaydamagethetool.

NOTICE: Do not trim the grass or weeds while

using the shear blades.Theshearbladesmay

become tangled in the grass or weeds.

Hold the tool with both hands, press the switch lever

andpulltheswitchtriggerwhilepressingthelock-o

lever, and then move it forward.

For basic operation, tilt the shear blades toward the

trimmingdirectionandmoveitcalmlyandslowlyatthe

speed rate of 3 to 4 seconds per meter.

Tocutahedgetopevenly,tieastringatthedesired

height and trim along it.

15 ENGLISH

If the chip receiver is attached to the shear blades, it

gathers discarded leaves and makes clean-up after-

ward much easier.

Tocutahedgesideevenly,cutfromthebottomtotop.

When trimming to make a round shape (trimming box-

wood or rhododendron, etc.), trim from the root to the

topforabeautifulnish.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

To maintain product SAFETY and RELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

beperformedbyMakitaAuthorizedorFactoryService

Centers,alwaysusingMakitareplacementparts.

Cleaning the tool

Cleanthetoolbywipingodustwithadryclothorone

dippedinsoapywaterandwrungout.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

Shear blade maintenance

Before the operation or once per hour during operation,

applylow-viscosityoil(machineoil,orspray-typelubri-

cating oil) to the shear blades.

After operation, remove dust from both sides of the

shearbladeswithawiredbrush,wipeitowithacloth

andthenapplylow-viscosityoil(machineoil,orspray-

typelubricatingoil)totheshearblades.

NOTICE: Do not wash the shear blades in water.

Doingsomaycauserustordamagetothetool.

NOTICE: Dirt and corrosion cause excessive

blade friction and shorten the operating time per

battery charge.

16 ENGLISH

Storage

The hook hole in the tool bottom is convenient for hang-

ing the tool from a nail or screw on the wall.

Attach the blade cover to the shear blades so that the blades

are not exposed. Store the tool out of the reach of children.

Store the tool in a place not exposed to moisture or rain.

►1. Hole

Grinding the shear blades

NOTICE:

If the shear blades have considerably deformed

by grinding, replace the shear blades with new ones.

1. Installthebatterycartridgetothetool.

2. Turn on and start the tool so that the upper blade

andlowerbladearepositionedalternately.

Turnothetoolandremovethebatterycartridgefromthetool.

Remove the screw, and then remove the branch catcher.

►1. Screw 2. Branch catcher

5. Settheangleofaleto45°(forUH004G/

UH005G/UH008G/UH009G) or 50° (for UH006G/

UH007G), and grind the upper blade from 3 directions

withthele.

►(1) File (2) 45° or 50°

CAUTION: Before grinding the shear blades,

make sure that the tool is switched o and the

battery cartridge is removed from the tool.

6. Place the tool upside down, and then remove the

burrs from the shear blades with the dressing stone.

►1. Dressing stone

7. Settheangleoftheleto45°(forUH004G/

UH005G/UH008G/UH009G) or 50° (for UH006G/

UH007G), and grind the lower blade from 3 directions

withthele.

8. Return the tool to normal position, and then

remove the burrs from the shear blades with the dress-

ing stone.

9. Attachthebranchcatcherbytighteningthescrew.

17 ENGLISH

Grease lubrication

Interval of lubrication:Every50operatinghours

1. Remove the bolt from the hole for lubrication.

►1. Bolt

2. Remove the cap from the grease vessel. Align the

outlet of the grease vessel with the hole on the cover,

and then press the outlet of the grease vessel onto the

hole.

►1. Grease vessel 2. Hole

3. Applythegreasetothetool(Approximately5g

(0.2 oz) as a guide).

4. Remove the grease vessel.

5. Tighten the bolt.

TROUBLESHOOTING

Beforeaskingforrepairs,conductyourowninspectionrst.Ifyoundaproblemthatisnotexplainedinthemanual,

donotattempttodismantlethetool.Instead,askMakitaAuthorizedServiceCenters,alwaysusingMakitareplace-

ment parts for repairs.

State of abnormality Probable cause (malfunction) Remedy

Motor does not run. Batterycartridgeisnotinstalled. Installthebatterycartridge.

Batteryproblem(undervoltage) Rechargethebattery.Ifrechargingisnoteective,

replacebattery.

Thedrivesystemdoesnotwork

correctly.

Askyourlocalauthorizedservicecenterforrepair.

Motor stops running after a little use. Battery'schargelevelislow. Rechargethebattery.Ifrechargingisnoteective,

replacebattery.

Overheating. Stop using of tool to allow it to cool down.

Tool does not reach maximum RPM. Batteryisinstalledimproperly. Installthebatterycartridgeasdescribedinthis

manual.

Batterypowerisdropping. Rechargethebattery.Ifrechargingisnoteective,

replacebattery.

Thedrivesystemdoesnotwork

correctly.

Askyourlocalauthorizedservicecenterforrepair.

Shear blades do not move:

stopthemachineimmediately!

Foreignobjectsarecaughtbetweenthe

shear blades.

1. Use the reverse button.

2.Switchothetoolandremovethebatterycar-

tridge,andthenremovetheforeignobjectsusing

tools such as pliers.

Thedrivesystemdoesnotwork

correctly.

Askyourlocalauthorizedservicecenterforrepair.

Abnormal vibration:

stopthemachineimmediately!

Shear blades are broken, bent or worn. Replace the shear blades.

Thedrivesystemdoesnotwork

correctly.

Askyourlocalauthorizedservicecenterforrepair.

Shear blades and motor cannot stop:

Removethebatteryimmediately!

Electric malfunction. Removethebatteryandaskyourlocalauthorized

service center for repair.

18 ENGLISH

OPTIONAL

ACCESSORIES

CAUTION: These accessories or attachments

are recommended for use with your Makita tool

specied in this manual.Theuseofanyother

accessories or attachments might present a risk of

injurytopersons.Onlyuseaccessoryorattachment

for its stated purpose.

Ifyouneedanyassistanceformoredetailsregard-

ingtheseaccessories,askyourlocalMakitaService

Center.

• Shearbladeassembly

• Shear blade cover

• Chip receiver

• Grease vessel

• Makitagenuinebatteryandcharger

NOTE:Someitemsinthelistmaybeincludedinthe

toolpackageasstandardaccessories.Theymay

dierfromcountrytocountry.

MAKITA LIMITED WARRANTY

Pleaserefertotheannexedwarrantysheetforthe

mostcurrentwarrantytermsapplicabletothisproduct.

Ifannexedwarrantysheetisnotavailable,refertothe

warrantydetailssetforthatbelowwebsiteforyour

respectivecountry.

United States of America: www.makitatools.com

Canada: www.makita.ca

Other countries: www.makita.com

19 FRANÇAIS

FRANÇAIS (Mode d’emploi original)

SPÉCIFICATIONS

Modèle : UH004G UH005G UH006G

Longueur de lame 600mm(23-5/8″) 750mm(29-1/2″) 600mm(23-5/8″)

Cisaillements par minute 2 000 / 3 600 / 5 000 /min 2 000 / 3 000 /

4 000 /min

Longueur totale 1120mm(44″) 1263mm(49-3/4″) 1123mm(44-1/4″)

Tension nominale C.C. 36 V - 40 V max.

Poids net 4,3 - 4,9 kg

(9,5 - 10,8 lbs)

4,5 - 5,1 kg

(9,9 - 11,2 lbs)

4,4 - 5,0 kg

(9,7 - 11,0 lbs)

Modèle : UH007G UH008G UH009G

Longueur de lame 750mm(29-1/2″) 600mm(23-5/8″) 750mm(29-1/2″)

Cisaillements par minute 2 000 / 3 000 /

4 000 /min

2 000 / 3 600 / 5 000 /min

Longueur totale 1274mm(50-1/4″) 1120mm(44″) 1262mm(49-3/4″)

Tension nominale C.C. 36 V - 40 V max.

Poids net 4,6 - 5,2 kg

(10,1 - 11,5 lbs)

4,3 - 4,9 kg

(9,5 - 10,8 lbs)

4,4 - 5,0 kg

(9,7 - 11,0 lbs)

• Étantdonnél’évolutionconstantedenotreprogrammederechercheetdéveloppement,lesspécications

contenuesdanscemanuelsontsujettesàmodicationsanspréavis.

• Lesspécicationspeuventvarierd’unpaysàl’autre.

• Lepoidspeutvarierselonlesaccessoires,ycomprislabatterie.Lapluslégèreetlapluslourdecombinaisons,

selon la procédure EPTA 01/2014, sont indiquées dans le tableau.

Batteries et chargeurs applicables

Batterie BL4025 / BL4040

Chargeur DC40RA

• Suivant la région où vous habitez, il se peut que certaines des batteries et certains des chargeurs énumérés

ci-dessus ne soient pas disponibles.

MISE EN GARDE : Utilisez exclusivement les batteries et chargeurs énumérés ci-dessus. L’utilisation

de toute autre batterie ou tout autre chargeur peut entraîner une blessure et/ou un incendie.

Support d’alimentation portable recommandé

Support d’alimentation portable PDC1200 / PDC01

• Suivant la région où vous habitez, il se peut que le(s) support(s) d’alimentation portable(s) énumérés ci-dessus

ne soient pas disponibles.

• Avant d’utiliser le support d’alimentation portable, lisez les instructions et les indications de mise en garde sur

lesupportd'alimentationportable.

20 FRANÇAIS

CONSIGNES DE

SÉCURITÉ

Consignes de sécurité générales

pour outils électriques

MISE EN GARDE : Lisez toutes les mises en

garde, instructions, illustrations et spécications

qui accompagnent cet outil électrique.Ilyarisque

de décharge électrique, d’incendie et/ou de blessure

grave si les instructions ci-dessous ne sont pas

toutes respectées.

Conservez toutes les mises en

garde et instructions pour réfé-

rence future.

Leterme«outilélectrique»quiguredanslesavertis-

sementsfaitréférenceàunoutilélectriquebranchésur

une prise de courant (par un cordon d’alimentation) ou

alimentéparbatterie(sansl).

Sécurité de la zone de travail

1. Maintenez la zone de travail propre et bien

éclairée. Les zones de travail encombrées ou

sombres ouvrent grande la porte aux accidents.

2. N’utilisez pas les outils électriques dans les

atmosphères explosives, par exemple en pré-

sence de liquides, gaz ou poussières inam-

mables. Les outils électriques produisent des

étincellesaucontactdesquelleslapoussièreou

lesvapeurspeuvents’enammer.

3. Assurez-vous qu’aucun enfant ou curieux ne

s’approche pendant que vous utilisez un outil

électrique. Vous risquez de perdre la maîtrise de

l’outil si votre attention est détournée.

Sécurité en matière d’électricité

1. Les ches d’outil électrique sont conçues pour

s’adapter parfaitement aux prises de courant.

Ne modiez jamais la che de quelque façon

que ce soit. N’utilisez aucun adaptateur de

che sur les outils électriques avec mise à

la terre. Ennemodiantpasleschesetenles

insérant dans des prises de courant pour les-

quelles elles ont été conçues, vous réduirez les

risques de choc électrique.

2. Évitez tout contact corporel avec les surfaces

mises à la terre, telles que tuyaux, radiateurs,

cuisinières et réfrigérateurs. Le risque de choc

électrique est plus élevé si votre corps se trouve

misàlaterre.

3. N’exposez pas les outils électriques à la pluie

ou à l’eau. La présence d’eau dans un outil élec-

trique augmente le risque de choc électrique.

4. Ne maltraitez pas le cordon. N’utilisez jamais

le cordon pour transporter, tirer ou débrancher

l’outil électrique. Maintenez le cordon à l’écart

des sources de chaleur, de l’huile, des objets à

bords tranchants et des pièces en mouvement.

Le risque de choc électrique est plus élevé lorsque

les cordons sont endommagés ou enchevêtrés.

5. Lorsque vous utilisez un outil électrique à l’ex-

térieur, utilisez un cordon prolongateur conçu

pour l’usage extérieur. Les risque de choc élec-

trique est moindre lorsqu’un cordon conçu pour

l’usage extérieur est utilisé.

6. Si vous devez utiliser un outil électrique dans

un endroit humide, utilisez une source d’ali-

mentation protégée par un disjoncteur de fuite

à la terre.L’utilisationd’undisjoncteurdefuiteàla

terre réduit le risque de choc électrique.

7. Les outils électriques peuvent produire des

champs électromagnétiques (CEM) qui ne sont

pas préjudiciables à l’utilisateur. Les utilisa-

teurs de stimulateur cardiaque ou autres appareils

médicaux similaires doivent toutefois demander

conseilaufabricantet/ouàleurmédecinavant

d’utiliser cet outil électrique.

Sécurité personnelle

1. Restez alerte, attentif à vos mouvements et

faites preuve de bon sens lorsque vous utili-

sez un outil électrique. N’utilisez pas les outils

électriques si vous êtes fatigué ou avez pris

une drogue, de l’alcool ou un médicament. Un

moment d’inattention pendant l’utilisation d’un

outil électrique peut entraîner une grave blessure.

Portez des dispositifs de protection personnelle.

Portez toujours une protection oculaire. Les risques

de blessure seront moins élevés si vous utilisez des

dispositifs de protection tels qu’un masque anti-pous-

sière,deschaussuresàsemelleantidérapante,une

coiurerésistanteouuneprotectiond’oreilles.

Évitez les démarrages accidentels. Assurez-

vous que l’interrupteur est en position d’arrêt

avant de brancher l’outil à la prise de courant

et/ou au bloc-piles, et avant de prendre ou de

transporter l’outil. Vous ouvrez la porte aux acci-

dents si vous transportez les outils électriques avec

le doigt sur l’interrupteur ou si vous les branchez

alors que l’interrupteur est en position de marche.

4. Retirez toute clé de réglage ou de serrage

avant de mettre l’outil électrique sous tension.

Touteclélaisséeenplacesurunepiècerotative

de l’outil électrique peut entraîner une blessure.

5. Ne vous étirez pas exagérément. Assurez-vous

d’une bonne prise au sol et d’un bon équilibre

en tout temps. Cela vous permettra d’avoir une

meilleure maîtrise de l’outil électrique dans les

situations imprévues.

Portez des vêtements adéquats. Ne portez ni

vêtements amples ni bijoux. Gardez vos cheveux,

vêtements et gants à l’écart des pièces en mouve-

ment.Lesvêtementsamples,bijouxoucheveuxlongs

peuventêtrehappésparlespiècesenmouvement.

7. Si des accessoires sont fournis pour raccorder

un appareil d’aspiration et de collecte de la

poussière, assurez-vous qu’ils sont correc-

tement raccordés et qu’ils sont utilisés de

manière adéquate. L’utilisation d’un appareil de

collectepermetderéduirelesrisquesliésàla

présencedepoussièredansl’air.

8. Évitez d’être complaisant et d’ignorer les

principes de sécurité de l’outil en raison de la

familiarité acquise par un usage fréquent des

outils. Un geste imprudent peut entraîner une

grave blessure en une fraction de seconde.

La page charge ...

Makita UH004G Manuel utilisateur

Marque: Makita

Modèle: UH004G

Catégorie: Taille-haies électriques

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Makita UH004G User manual
español: Makita UH004G Manual de usuario

Makita UH004G Manuel utilisateur

Makita UH004G Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents