Hisense MWH409S WiFi Module Manuel utilisateur

Hisense
Marque
Hisense
Modèle
MWH409S WiFi Module
Taper
Manuel utilisateur
The user manual of TV’s WIFI module
1. The product description
The user can achieve TV connection WIFI net, through this module and the voltage supplied by the system to the
module needs to be transmitted by a voltage regulator or circuit
This equipment may be operated in all European countries.
The module installation method is as follows: pass the large round hole of the module through the limit column of
the bracket of the TV, and fix the module by the snap-fit on the bracket. Connect the external IPEX antenna to the
antenna pedestal of the module
2. Basic parameters
Feature Description
Feature Description
Model
MWH409S
Product Name
WiFi Module
FCC ID
SARMWH409S
IC
27123-MWH409S
Interface
USB2.0
Supply Voltage
3.3V±0.33V
Dimension
28（mm）*16（mm）*3.05(mm)
Operating Temperature
-10°C to 70°C
Storage Temperature
-40°C to 85°C
3. RF output power
Band
Limited power
WlAN
2412MHZ-2462MHZ
<20
4. The display method of Model approved code
In the factory，the model approve code is pasted on the back shell in a label.
5. FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in
accordance with the instructions may cause harmful interference to radio communications. However there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures：
⚫ Reorient or relocate the receiving antenna.
⚫ Increase the separation between the equipment and receiver.
⚫ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
⚫ Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
Labelling Instruction for Host Product Integrator
Please notice that if the FCC identification number is not visible when the module is installed inside another device, then
the outside of the device into which the module is installed must also display a label referring to the enclosed module.
This exterior label can use wording such as the following: “Contains FCC ID: SARMWH409S” any similar wording that
expresses the same meaning may be used.
Installation Notice to Host Product Manufacturer
The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module.
The module is limited to installation in mobile application, a separate approval is required for all other operating
configurations, including portable configurations with respect to §2.1093 and difference antenna configurations.
Antenna Change Notice to Host manufacturer
If you desire to increase antenna gain and either change antenna type or use same antenna type certified, a Class II
permissive change application is required to be filed by us, or you (host manufacturer) can take responsibility through
the change in FCC ID (new application) procedure followed by a Class II permissive change application.
6. Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also
complies with Part 15 of FCC RF Rules. This equipment should be installed and operated with minimum distance of 20cm
in between the radiator and your body. This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter
CAUTION:
To comply with the limits of the Class B digital device pursuant to Part 15 of the FCC Rules, this device is compliant with
Class B limits. All peripherals must be shielded and grounded. Operation with non-certified peripherals or non-shielded
cables may results in interference to radio or reception
MODIFICATION
To assure continued compliance, Any changes or modifications not expressly approved by the grantee of this device
could void the users authority to operate the device.
7. Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance of 20 cm(8 in )between the radiator and your body NOTE To
satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product Contains
Transmitter module FCC ID: ******* To satisfy IESD exterior labeling requirements, the following text must be placed on
the exterior of the end product " Contains Transmitter module IC: *******
This symbol on the product or on its packaging indicates that this product must not be disposed of with your household
waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated
collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of
your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a
manner that protects human health and the environment. For more information about where you can drop off your
waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop
where you purchased the product.
8. IC Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1 )This device
may not cause interference.(2)This device must accept any interference, including interference that may cause
undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :(1)L’appareil ne doit pas produire de brouillage; (2)L’appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
This equipment complies with IC RSS‐102 radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Cet équipement est conforme aux limites d'exposition aux radiations IC CNR‐102 établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20cm entre le radiateur et votre
corps.
Please notice that if the IC identification number is not visible when the module is installed inside another device, then
the outside of the device into which the module is installed must also display a label referring to the enclosed module.
This exterior label can use wording such as the following: “Contains IC: 27123-MWH409S” any similar wording that
expresses the same meaning may be used.
L’étiquette d’homologation d’un module d’Innovation, Sciences et Développement économique Canada devra être
posée sur le produit hôte à un endroit bien en vue, en tout temps. En l’absence d’étiquette, le produit hôte doit porter
une étiquette sur laquelle figure le numéro d’homologation du module d’Innovation, Sciences et Développement
économique Canada, précédé du mot « contient », ou d’une formulation similaire allant dans le même sens et qui va
comme suit : Contient IC: 27123-MWH409S est le numéro d’homologation du module.
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two
conditions:
"Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device."
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’
exploitation est autorisée aux deux conditions suivantes :
1) l’appareil ne doit pas produire de brouillage;
2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC：27123-MWH409S
Manufacturer: Qingdao Hisense Communication Co., Ltd.
Address: 218 Qianwangang Road, Qingdao Economic & Technological Development Zone,
Qingdao, China
Importers:
Hisense France SAS
Address: 9 Rue des 3 Soeurs, 93420 Villepinte, France
Hisense Iberia, S.L.U
Address: Ronda Auguste y Louis Lumiere. 23 Nave 12. Edificio Lumiere - Parque
Tecnológico 46980
Paterna (Valencia) - Spain
Hisense Italia S.r.l
Address: Via Montefeltro, 6/A, 20156 MILANO
Hisense South Africa
Address: The Estuaries, Building 17 Oxbow Crescent, Century City, Cape Town, SouthAfrica
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Hisense MWH409S WiFi Module Manuel utilisateur

Hisense
Marque
Hisense
Modèle
MWH409S WiFi Module
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents