Scotts 62162S Le manuel du propriétaire

OWNER’S MANUAL

21 in. - 62 VOLT LITHIUM-ION CORDLESS MOWER

5.0Ah Lithium-ion Battery

Model 62162S

Your lawn mower has been engineered and manufactured to our high standard for dependability, ease of operation,

and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the owner’s manual before using

this product.

Thank you for your purchase.

SAVE THIS MANUAL FOR FUTURE REFERENCE

244026 CA Compliant

Charger Included

(Model No.

CHL86200)

BATTERY MUST BE CHARGED

BEFORE FIRST USE. TWO TO

THREE INITIAL CHARGING/

DISCHARGING CYCLES MAY BE

REQUIRED TO ACHIEVE MAXIMUM

RUN TIME/CAPACITY.

DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING,

ASSEMBLY, PARTS, SERVICE QUESTIONS? GO TO

SCOTTS.AMERICANLAWNMOWER.COM OR CALL 1-800-618-7474

BETWEEN 8:00 AM—5:00 PM EST FOR ASSISTANCE.

• Introduction…………………………………..…………………………………………...2

• Important Safety Instructions.………………………...……………………………...3-5

• Symbols……………………………………..…………………………………………... 6

• Features………………………………………………………………………………. 7-8

• Assembly…………………………………………………………………...………...8-10

• Operation…………………………………...……………………………...……….11-12

• Charging the battery pack……………………………………………………………..13

• Maintenance………………………………..………………………………...…….14-16

• Troubleshooting…...…...………………………………….…………………….……. 17

• Parts and Service.………………………….…………………………………………..18

• Notes…………………………………………………………………………………….19

• Warranty………………………………………..………………………...……Back Page

INTRODUCTION

This product has many features for making its use more pleasant and enjoyable. Safety, performance,

and dependability have been given top priority in the design of this product making it easy to maintain

and operate.

TABLE OF CONTENTS

SAVE THESE INSTRUCTIONS

2

Model 62162S

Refer to the recommended ambient temperature range for appliance and battery use and

storage, and for charging system during charging.

WARNING:

To avoid serious injury, do not attempt to use this product until you read thoroughly and understand

completely the owner‘s manual. If you do not understand the warnings and instructions in the owner‘s

manual, do not use this product. Call Scotts customer service for assistance.

WARNING:

The operation of any power tool can result in foreign objects being thrown into your eyes,

which can result in severe eye damage. Before beginning power tool operation, always wear

safety goggles or safety glasses with side shields and, when needed, a full face shield. We

recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses

with side shields. Always use eye protection which is marked to comply with ANSI Z87.1.

Recommended Ambient Temperature Range

Mower Operation 41 °F - 104 °F (5 °C - 40 °C)

Mower Storage 32 °F - 100 °F (0 °C - 38 °C)

Battery Charging 39 °F - 104 °F (4 °C - 40 °C)

Charger Operation 39 °F - 104 °F (4 °C - 40 °C)

Battery Storage 32 °F - 104 °F (0 °C - 40 °C) for 3 months before charging is required.

Battery Discharging 32 °F - 104 °F (0 °C - 40 °C)

IMPORTANT SAFETY INSTRUCTIONS

3

Model 62162S

WARNING:

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed below and on the

machine may result in electric shock, fire, and/or serious

personal injury.

SAFETY INSTRUCTIONS FOR PEDESTRIAN-CONTROLLED

MOWERS

IMPORTANT - Safe Practices for Pedestrian-Controlled

Mower

This machine is capable of amputating hands and feet and

throwing objects. Failure to observe the following safety

instructions could result in serious injury or death.

I. GENERAL INFORMATION

1. Read, understand, and follow instructions and warnings in

this manual and on the machine, engine and attachments.

2. Only allow operators, who are responsible, trained, familiar

with the instructions, and physically capable to operate the

machine.

3. Keep bystanders away.

4. Do not operate the machine while under the influence of

alcohol or drugs.

II. PREPARATION BEFORE OPERATING

1. Clear the operating area of any objects which could be

thrown by or interfere with operation of the machine.

2. Keep the area of operation clear of all bystanders,

particularly small children. Stop the machine and

attachment (s) if anyone enters the area.

3. Do not operate the machine without the entire grass

catcher, discharge chute, or other safety devices in place

and functioning properly. Check frequently for signs of wear

or deterioration and replace as needed.

4. Wear appropriate personal protective equipment such as

safety glasses, hearing protection, and footwear.

III. OPERATING

1. Only operate the machine in daylight or good artificial light.

2. Avoid holes, ruts, bumps, rocks, or other hidden hazards.

Uneven terrain could overturn the machine, or cause

operator to lose their balance or footing.

3. Do not put hands or feet near rotating parts or under the

machine. Keep clear of the discharge opening at all times.

4. Do not direct discharge material toward anyone. Avoid

discharging material against a wall or obstruction. Material

may ricochet back toward the operator. Stop the blade (s)

when crossing gravel surfaces.

5. Do not leave a running machine unattended. Always park

on level ground, disengage the attachment,, and stop

engine.

6. Do not mow in reverse unless absolutely necessary.

Always look down and behind before and while backing.

IV. CHILDREN SPECIFIC

1. Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

machine and the mowing activity. Never assume that

children will remain where you last saw them.

2. Keep children out of the operating area and under the

watchful care of a responsible adult other than the

operator.

V. SLOPE SPECIFIC

Slopes are a major factor related to accidents. Operation on

slopes requires extra caution.

1. Travel in the manufacturer recommended direction on

slopes. Use caution while operating near drop-offs.

2. Avoid mowing wet grass. (Poor footing could cause a slip

and fall accident.)

3. Do not operate machine under any condition where

traction, steering, or stability is in question. Tires could slide

even if the wheels are stopped.

4. Always keep the machine in gear when going down slopes.

Do not coast downhill.

5. Avoid starting and stopping on slopes. Avoid making

sudden changes in speed or direction. Make turns slowly

and gradually.

6. Use extra care while operating machine with a grass

catcher or other attachment (s). They can affect the stability

of the machine.

VI. HAULING

1. Use full width ramps for loading and unloading a machine

for transport.

VII. SERVICE

1. Keep machine in good working order. Replace worn or

damaged parts.

2. Use caution when servicing blades. Wrap the blade (s) or

wear gloves. Replace damaged blades. Do not repair or

alter blade (s).

3. Remove or disconnect battery before servicing or making

any repairs.

WARNING: California Proposition 65:

This product contains chemicals known to the State of

California to cause cancer, birth defects or other reproductive

harm.

WARNING: Some dust and debris created by the use of this

tool could contain chemicals known to the State of California to

cause cancer and birth defects or other reproductive harm.

Some examples of these chemicals are:

 Chemicals in fertilizers

 Compounds in insecticides, herbicides and pesticides

 Arsenic and chromium from chemically treated lumber

Your risk from exposure to these chemicals varies, depending

on how often you do this type of work. To reduce your

exposure, work in a well-ventilated area and with approved

safety equipment, such as dust masks that are specially

designed to filter out microscopic particles.

WARNING: Cancer and Reproductive Harm –

www.P65Warnings.ca.gov.

IMPORTANT SAFETY INSTRUCTIONS

4

Model 62162S

• Avoid Dangerous Environment - Do not use the lawn mower in

damp or wet conditions or operate in the rain.

• Keep the area clear of all bystanders, children, and pets while

mowing. Stop machine if anyone enters the area.

• Dress properly - Do not wear loose clothing or jewelry. They

can be caught in moving parts. Use of rubber gloves and

footwear is recommended when working outdoors.

• Don’t over reach - Keep firm footing and balance. Do not

overreach. Over-reaching can result in loss of balance.

• Do not operate the equipment with barefoot or when wearing

sandals or similar lightweight footwear. Wear protective

footwear that will protect your feet and improve your footing on

slippery surfaces.

• Use safety glasses - Always wear safety glasses with side

shields. Everyday glasses have only impact resistant lenses.

They are NOT safety glasses. Following this rule will reduce

the risk of eye injury. Use face mask if environment is dusty.

• Wear safety glasses or goggles that are marked to comply with

ANSI Z87.1 standard when operating this product.

• Use the right appliance - Do not use the lawn mower for any

job except that for which it is intended.

• Do not force the lawn mower - It will do the job better and safer

at the rate for which it was designed.

• Stay alert - Watch what you are doing, and use common sense

when operating the lawn mower. Do not operate the mower

while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating the lawn

mower may result in serious personal injury.

• Maintain lawn mower with care - Keep machine in good

working condition. Keep blades sharp and guards in place and

in working order.

• Check all nuts, bolts, and screws at frequent intervals for

proper tightness to be sure the equipment is in safe working

condition.

• Stop the motor, remove the switch key and wait until the blade

comes to a complete stop before cleaning the lawn mower,

removing the grass catcher, unclogging the discharge opening,

or making any repairs or inspections.

• When not in use, mower should be stored indoors in a dry,

locked up place—out of reach of children.

• Always use safety protective devices. Do not operate the

mower without the entire grass catcher discharge guard, rear

guard, or other safety protective devices in place and working.

• Follow manufacturer’s instructions for proper operation and

installation of accessories. Only use accessories approved by

the manufacturer.

• Do not mow on wet grass or excessively steep slopes. Poor

footing could cause a slip and fall accident. Walk, never run.

• Use extra care when approaching blind corners, shrubs, trees,

or other objects that may block your view.

• Clear the work area before each use. Remove all objects such

as rocks, sticks, wire, bones, toys, or other objects which can

be thrown by the blade. Stay behind the handle when the

motor is running.

• Do not mow near drop-offs, ditches, or embankments.

• Mow across the face of slopes, never up and down. Exercise

extreme caution when changing direction on slopes.

• Plan your mowing pattern to avoid discharge of material

towards roads, sidewalks, bystanders and the like. Also, avoid

discharging material against a wall or obstruction, which may

cause the material to ricochet back toward the operator.

• Do not pull the mower backward unless absolutely necessary.

If you must back the mower away from a wall or obstruction

first look down and behind to avoid tripping.

• Objects struck by the lawn mower blade can cause severe

injuries to persons. The lawn should always be carefully

examined and cleared of all objects prior to each mowing.

• If the lawn mower strikes a foreign object, follow these steps:

 Stop the lawn mower and release the switch control

bail wire,

 Remove the switch key

 Thoroughly inspect the mower for any damage

 Repair any damage before restarting and continuing to

operate the mower.

• Stop the motor, remove the switch key, and wait until the blade

comes to a complete stop before removing the grass catcher

or unclogging the chute, The cutting blade continues to rotate

for a few seconds after the motor is shut off. Never place any

part of the body in the blade area until you are sure the blade

has stopped rotating,

• If the mower should start to vibrate abnormally, stop the motor

and check immediately for the cause. Vibration is generally a

warning of trouble.

• Service on the product must be performed by qualified repair

personnel only. Service or maintenance performed by

unqualified personnel could result in injury to the user or

damage to the product.

• Use only identical replacement parts when servicing the

product. Use of unauthorized parts may create a risk of

serious injury to the user or damage to the product.

• Replace blade if it is bent or cracked. An unbalanced blade

causes vibration that could damage the motor drive unit or

cause personal injury. Sharpen a dull blade equally at each

end to maintain the balance. Clean the blade thoroughly and

check its balance by supporting it horizontally on a thin nail

through its center hole. The nail should be in a horizontal

position. If either end of the blade rotates downward, remove

some metal from the heavy or lower end until the blade is

balanced. It is balanced when neither end drops.

• The grass bag assembly is subject to deterioration and wear

and should be checked each time the mower is used. If

replacement is needed, make sure the new grass bag meets

original manufacturer’s recommendations and specifications.

• Maintain or replace safety instructions labels, as necessary.

• Store idle lawn mower indoors - When not in use, mower

should be stored indoors in a dry, locked place out of the reach

of children. The start key should also be removed and stored in

a separate location out of the reach of children.

• Follow instructions for lubricating and changing accessories.

• Never operate machine in a closed area.

• Never tamper with safety devices. Check for proper operation

regularly.

• Never attempt to make a wheel height adjustment while the

motor is running.

• Do not wash with a hose; avoid getting water in motor and

electrical connections.

IMPORTANT SAFETY INSTRUCTIONS

5

Model 62162S

SAFETY RULES FOR BATTERY AND CHARGER

• Prevent unintentional starting. Ensure the switch is in the

off-position before connecting to battery pack, picking up or

carrying the appliance. Carrying the appliance with your

ﬁnger on the switch or energizing appliance that have the

switch on invites accidents.

• Disconnect the battery pack from the appliance before

making any adjustments, changing accessories, or storing

appliance. Such preventive safety measures reduce the risk

of starting the appliance accidentally.

• Recharge only with Scotts 62V charger (CHL86200). A

charger that is suitable for one type of battery pack may

create a risk of ﬁre when used with another battery pack.

• Use appliances only with Scotts 62V lithium-ion battery

packs (BL86225, BL86240, BL86250). Use of any other

battery packs may create a risk of injury and ﬁre. See

Charger Manual.

• When battery pack is not in use, keep it away from other

metal objects, like paper clips, coins, keys, nails, screws or

other small metal objects, that can make a connection from

one terminal to another. Shorting the battery terminals

together may cause burns or a ﬁre.

• Under abusive conditions, liquid may be ejected from the

battery; avoid contact. If contact accidentally occurs, ﬂush

with water. If liquid contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause irritation or

burns.

• Do not use a battery pack or appliance that is damaged or

modiﬁed. Damaged or modiﬁed batteries may exhibit

unpredictable behavior resulting in ﬁre, explosion or risk of

injury.

• Do not expose a battery pack or appliance to ﬁre or

excessive temperature. Exposure to ﬁre or temperature

above 265°F (130°C) may cause explosion.

• Follow all charging instructions and do not charge the

battery pack or appliance outside of the temperature range

speciﬁed in the instructions. Charging improperly or at

temperatures outside of the speciﬁed range may damage

the battery and increase the risk of ﬁre. See Charger

Manual.

• Have servicing performed by a qualiﬁed repair person using

only identical replacement parts. This will ensure that the

safety of the product is maintained.

• Do not modify or attempt to repair the appliance or the

battery pack (as applicable) except as indicated in the

instructions for use and care.

• Do not open or mutilate battery (ies). Released battery fluid

may cause damage to the eyes, or skin. It may be toxic if

swallowed.

• Exercise care in handling batteries in order not to short the

battery with conducting materials such as rings, bracelets,

and keys. The battery or conductor may overheat and cause

burns.

• Disconnect battery - Disconnect battery pack from the

appliance before storing, servicing, transporting, or changing

accessories such as blades. Such preventive safety

measures reduce the risk of starting the tool accidentally.

• Stop the unit and disconnect battery pack and start key

when not in use. Carry or push the unit with the motor

stopped and the start key and battery pack removed from

the mower.

• Battery tools do not have to be plugged into an electrical

outlet; therefore, they are always in operating condition.

Be aware of possible hazards when not using your

battery tool or when changing accessories. Following this

rule will reduce the risk of electric shock, fire, or serious

personal injury.

• Do not use battery-operated appliance in rain.

• Remove or disconnect battery before servicing, cleaning

or removing material from the gardening appliance.

• Do not charge lawn mower in rain, or in wet locations.

• Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away from

heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

• Use of an attachment not recommended or sold by the

battery charger manufacturer may result in a risk of fire,

electric shock, or injury to persons. Following this rule will

reduce the risk of electric shock, fire, or serious personal

injury.

• Do not service mower with battery, switch key, or charger

installed.

• Do not use the charger when the ambient temperature is

above 104°F (40°C) or below 39°F (4°C).

• Do not operate charger with a damaged cord or plug

which could cause shorting and electric shock. If

damaged, replace the charger with an identical charger

from an authorized service provider.

• Do not operate charger if it has received a sharp blow,

been dropped or otherwise damaged in any way. Take it

to an authorized service center for electrical check to

determine if the charger is in good working order.

• Unplug charger from outlet before attempting any

maintenance or cleaning to reduce the risk of electric

shock.

• Disconnect charger from the power supply when not in

use to prevent damage to the charger during a power

surge,

• Risk of electric shock, Do not touch uninsulated portion of

output connector or uninsulated battery terminal.

• Do not expose charger to wet or damp conditions, Water

entering charger will increase the risk of electric shock,

• Make sure cord is located so that it will not be stepped on,

tripped over, come in contact with sharp edges or moving

parts or otherwise subjected to damage or stress. This will

reduce the risk of accidental falls, which could cause

injury, and damage to the cord, which could result in

electric shock.

• Keep cord and charger away from heat to prevent

damage to housing or internal parts.

• Do not let gasoline, oils, petroleum-based products, etc.

come in contact with plastic parts. They contain chemicals

that can damage, weaken or destroy plastic.

Save these instructions. Refer to them frequently and

use them to instruct others who may use this product. If you

loan someone this tool, loan them these instructions also.

Some of the following symbols may be used on this product. Please study them and learn their

meaning. Proper interpretation of these symbols will allow you to operate the product better

and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

hrs Hours Time

Gal Gallon Volume

qt Quart Volume

Wet Conditions Alert Do not expose to rain or use in damp locations

Read the Owner’s Manual To reduce the risk of injury, user must read and

understand owner’s manual before using this product.

Eye Protection Always wear safety goggles or safety glasses with side

shields and, as necessary, a full face shield when

operating this product.

Safety Alert Precautions that involve safety

Electric Shock Failure to use in dry conditions and to observe safe

practices can result in electric shock

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated

with this product.

SYMBOL SIGNAL MEANING

DANGER Indicates an imminently hazardous situation, which, if not

avoided, will result in death or serious injury.

WARNING Indicates a potentially hazardous situation, which, if not

avoided, could result in death or serious injury.

CAUTION Indicates a potentially hazardous situation, which, if not

avoided, may result in minor or moderate injury.

CAUTION (Without Safety Alert Symbol) Indicates a situation that

may result in property damage.

6

Model 62162S

FEATURES

PRODUCT SPECIFICATIONS

62162S

*Battery…………………...62V 5.0Ah Lithium-ion Battery

Input………………………………………….. 62V DC only

No-load Speed………………………………... 2650 RPM

Charge time.…………………………………..180 minutes

Height Adjustments…………………..1-1/2 in. to 3-3/4 in.

Wheel Size………………………….7 in. front, 10 in. rear

Grass Catcher Capacity…………………1.7 Bushel (60L)

Weight………………………………………59.5 lbs (27 kg)

* This product contains a rechargeable lithium-ion battery. Battery must be recycled. Do not dispose of this product in

fire. Battery inside this product may explode or leak. Before disposing of damaged or worn out battery packs contact

your local waste disposal agency or the local Environmental Protection Agency for information and specific instructions.

Take the battery to a local recycling and/or disposal center for disposal. Never throw the battery pack away in a standard

receptacle or have it incinerated. See page 13 for more details.

Side Discharge Deflector

Mulching Plug

62V Charger

62V Battery

7

Model 62162S

Upper Handle

Safety Lock-out

Button Bail Wire

Lower Handle

Cam Lock Knob

Grass Catcher

T-Knob

T-Knob Rear Door

Rear Wheel

Front Wheel

Side Discharge

Cover

Height

Adjustment

Lever

Battery Cover

Fig. 1

Front Handle

Switch Key

UNPACKING

This product requires assembly.

• Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing

list are included.

• Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

• Do not discard the packing material until you have

carefully inspected and satisfactorily operated the

product.

• If any parts are damaged or missing, please call

1-800-618-7474 for assistance.

PACKING LIST

MOTOR/BLADE CONTROL ASSEMBLY

The motor/blade control, located on the upper handle of

the mower, engages and disengages the motor and

blade.

MULCHING PLUG

Your mower is equipped with a mulching plug that

allows the blade to cut and recut the grass for finer

clippings.

SWITCH KEY

The switch key must be inserted before the mower can

be started.

SIDE DISCHARGE DEFLECTOR

Use the side discharge deflector on your mower when

the grass is too high to mulch or when side discharging

is preferred. The grass clippings produced when using

the side discharge deflector are noticeably larger than

those produced when using the mulching plug.

KNOW YOUR LAWN MOWER

See figure 1

The safe use of this product requires an understanding of

the information on the product and in this owner’s

manual as well as a knowledge of the project you are

attempting. Before use of this product, familiarize yourself

with all operating features and safety rules.

BATTERY METER

The battery meter measures the amount of charge

remaining in the battery.

GRASS CATCHER

The grass catcher prevents grass clippings from being

strewn across your lawn as you mow.

HEIGHT ADJUSTMENT LEVER

The height adjustment lever provides cutting height

adjustments.

WARNING:

Do not insert switch key until assembly is complete.

Failure to comply could result in accidental starting

and possible serious injury.

WARNING:

Do not attempt to modify this product or create

accessories not recommended for use with this

product. Any such alteration or modification is

misuse and could result in a hazardous condition

leading to possible serious personal injury.

WARNING:

If any parts are damaged or missing do not operate

this product until the parts are replaced. Failure to

heed this warning could result in serious personal

injury.

DANGER:

To prevent accidental starting do not make any

adjustments or installations with the switch key

inserted or batteries installed.

FEATURES

ASSEMBLY

WARNING:

Never operate the mower without the proper safety

devices in place and working. Never operate the

mower with damaged safety devices. Failure to heed

this warning can result in serious personal injury.

Description Quantity

Lawn Mower 1

Switch Key 1

Mulching Plug 1

Side Discharge Deflector 1

Grass Catcher 1

Cam Lock Knob 2

62V 5.0Ah Battery 1

62V Charger 1

Owner‘s manual 1

8

Model 62162S

UNFOLDING AND ADJUSTING HANDLE ASSEMBLY

See figure 2

WARNING Folding or unfolding the handle improperly

can damage the cables, causing an unsafe operating

condition.

• Do not damage the cables when folding or

unfolding the handle.

• If a cable is damaged, contact an Authorized

Service Dealer.

To raise handle assembly:

• Pull up and back on the lower handle (1) until it is

aligned with the hole position of the arm support

and the mower housing.

• To secure the lower handle (1) in place, turn the

T-knobs (3) 90 degree until the lock pin is engaged

in one of the three locked stand-up positions (4).

• Open the upper cam locks (2).

• Pull up and back on the upper handle to raise it into

operating position.

• To secure the upper handle in place, close the

upper cam locks (2).

NOTE: If the upper handle is loose or separated from

the lower handle, tighten the knobs on the upper handle

locks by turning them clockwise.

INSTALLING THE GRASS CATCHER BAG

(For Rear Bagging Operation)

See figure 3

• Lift the rear discharge door (1).

• Lift the grass catcher by its handle (2) and place

under the rear discharge door so that the hooks (3)

on the grass catcher are seated on the door rod (4).

• Release the rear discharge door. When installed

correctly, the hooks on the grass catcher will extend

through the openings on the rear discharge door.

ASSEMBLY

NOTE: When using the grass catcher, do not install

either the side discharge deﬂector or the mulching plug.

REMOVING/INSTALLING THE MULCHING PLUG

(For Mulching Operation)

See figure 4

The mulching plug must be removed in order to install

the grass catcher.

• To remove the mulching plug, lift the rear discharge

door (1).

• Grasp the handle (2) of the mulching plug. Lift and

pull the mulching plug out using the handle.

• The mulching plug (3) is inserted at an angle, so it

requires some force to remove it.

The mulching plug must be re-installed when the grass

catcher is removed.

• To install the mulching plug, lift the rear discharge

door (1).

• Grasp the handle (2) of the mulching plug. Lift and

insert the mulching plug in at an angle using the

handle.

9

Model 62162S

1

3

2

Fig. 2

2

3

4

1

Fig. 3

Fig. 4

1

2

3

4

ASSEMBLY

NOTE: When mulching, do not install either the side

discharge deﬂector or the grass catcher.

INSTALLING SIDE DISCHARGE CHUTE

(For Side Discharging Operation)

See figure 5

• Lift the side discharge cover (1).

• Align the grooves (2) on the side discharge

deflector (3) with the pins (4) on the underside of

the discharge cover (1).

• Lower the discharge chute until the hooks on the

mower deck are secured in the openings in the

discharge chute.

• Release the side discharge cover.

NOTE: When using side discharge, do not install the

grass catcher. Ensure the mulch plug is installed.

INSTALLING/REMOVING BATTERY PACK

See figure 6

To Install Battery Pack

• Lift and hold up the battery cover (1).

• Align the battery (2) with the mower’s battery port.

• Make sure the battery release button (3) snaps in

place and that battery is fully seated and secure in

the mower before beginning operation.

• If the machine is not going to be used

immediately, remove the battery.

To Remove Battery Pack

• Release the bail lever to stop the mower.

• Press the battery release button (3) on the mower.

Open the battery cover.

• Remove battery from the mower.

This product will accept Scotts 62V lithium-ion

battery packs only.

For complete charging instructions, refer to the

Owner‘s manuals for your battery pack and charger

models.

WARNING: Always remove battery pack from your tool

when you are assembling parts, making adjustments,

cleaning, carrying, transporting or when not in use.

Removing battery pack will prevent accidental starting

that could cause serious personal injury.

NOTE: To avoid serious personal injury, always remove

the battery pack and keep hands clear of the trigger

release button when carrying or transporting the tool.

WARNING: Make sure the latch on the tool snaps in

place and the battery pack is fully seated and secure in

the battery port before beginning operation. Failure to

securely seat the battery pack could cause the battery

pack to fall out, resulting in serious personal injury.

SWITCH KEY

In order to prevent accidental start-up or unauthorized

use of your cordless mower, a removable switch key

has been incorporated into the design of your mower.

The mower will be completely disabled when the switch

key has been removed from the mower.

WARNING: The cord on the switch key is used for

storage; keep it out of the reach of children. DO NOT

tether the switch key to mower.

DANGER: Rotating blades can cause serious injury. To

prevent serious injury, remove the switch key when the

mower is unattended, or when adjusting, cleaning,

servicing, transporting, lifting, or storing the mower.

10

Model 62162S

1

2

3

4

Fig. 5

Fig. 6

2

3

1

WARNING:

Do not allow familiarity with this type of product to make you

careless. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear safety goggles or safety glasses with side shields

when operating this product. Failure to do so could result in

objects being thrown into your eyes, resulting in possible

serious injury.

WARNING:

Do not use any attachments or accessories not

recommended by the manufacturer of this product. The use of

attachments or accessories not recommended can result in

serious personal injury.

APPLICATIONS:

You may use this product for the purpose listed below:

• Mowing your lawn

OPERATION

STARTING/STOPPING THE MOWER

See figure 7

To start the mower:

• Raise the battery cover.

• Install battery pack.

• Insert the switch key (1) into the slot beside the

battery port.

• Lower the battery cover.

• Press and hold the safety lock-out button (2).

• While continuing to hold the start button, pull the

bail wire (3) toward the handle. Once the motor

starts, release the button.

To stop the mower:

• Release the bail wire.

SOFT-START

This LI-ION mower is equipped with a “soft- start”

feature. When initially starting up, the mower will take

approx. 3 seconds to get up to full speed. If the

mower does not initially start: Remove the battery

and check under the mower deck to ensure there is

nothing obstructing the blade and that the blade can

spin freely by hand. Even a small amount of grass on

start up will prevent the “softstart” from turning the

mower on.

CAUTION: Do not attempt to override the operation

of the safety lock-out button or bail lever.

WARNING: The operation of any mower can result in

foreign objects being thrown into the eyes, which can

cause severe eye damage. Always wear safety

glasses while operating the mower and while

performing any adjustments or repairs.

WARNING: Ensure that other people and pets

remain at least 100 feet (30 m) away when the

mower is in use.

INSPECT THE CUTTING AREA

Remove all stones, sticks, wire, bones, and other

debris that might be thrown by the rotating blades.

SETTING BLADE HEIGHT

See figure 8

When shipped, the wheels on the mower are set to a

low-cutting position. Before using the mower for the

first time, adjust the cutting position to the height best

suited for your lawn. The average lawn should be

between 1-1/2 in. to 2 in. during the cool months and

between 2 in. to 3 1/4 in. during the hot months.

The mower can be set to 6 cutting heights between

1.5" (38mm) and 3.75" (95mm). Choose the proper

cutting height according to the types and conditions

of the grass.

To adjust the blade height:

• To raise the blade height, grasp the height

adjustment lever (1) and move it toward the back

of the mower.

• To lower the blade height, grasp the height

adjustment lever (1) and move it toward the front

of the mower.

3

Fig. 7

11

Model 62162S

Fig. 8

1

2 1

MOWING TIPS

• Make sure the lawn is clear of stones, sticks, wires

and other objects that could damage the lawn mower

blades or motor. Such objects could be accidentally

thrown by the mower in any direction and cause

serious personal injury to the operator and others.

• For a healthy lawn, always cut off one-third or less

of the total length of the grass

• When cutting heavy grass, reduce walking speed

to allow for more effective cutting and a proper

discharge of the clippings.

• Do not cut wet grass. It will stick to the underside

of the deck and prevent proper mulching of grass

clippings.

• New or thick grass may require a narrower cut.

• Clean the underside of the mower deck after each

use to remove grass clippings, leaves, dirt and any

other accumulated debris.

SLOPE OPERATION

See figure 9

WARNING: Slopes are a major factor related to slip and

fall accidents that can result in severe injury. Operation

on slopes requires extra caution. If you feel uneasy on a

slope, do not mow it. For your safety, do not attempt to

mow slopes greater than 15 degrees.

• Mow across the face of slopes, not up and down.

Exercise extreme caution when changing direction

on slopes.

• Watch for holes, ruts, rocks, hidden objects, or

bumps which can cause you to slip or trip. Tall grass

can hide obstacles. Remove all objects such as

rocks, tree limbs, etc., which could be tripped over or

thrown by the blade.

• Always be sure of your footing. A slip and fall can

cause serious personal injury. If you feel you are

losing your balance, release the switch control bail

wire immediately.

• Do not mow near drop-offs, ditches, or

embankments; you could lose your footing or

balance.

OPERATION

MULCHING TIPS

NOTE: Inspect the area where the mower is to be

used, and remove all stones, sticks, wire, bones, and

other debris that might be thrown by the rotating

blade.

• Release the bail lever to turn the mower OFF

when crossing any graveled area (stones can be

thrown by the blade).

• Set mower to the highest cutting height when

mowing on uneven ground or in tall weeds.

• For eﬀective mulching, do not cut wet grass,

because it tends to stick to the underside of the

deck, preventing proper mulching of grass

clippings. New or thick grass may require a

narrower cut. The ground speed should be

adjusted to the condition of the lawn. If mowing

has been delayed and the grass has been

allowed to grow longer than 4” (10cm), mow the

lawn twice in order to reduce the grass height to a

maximum of 3 1/4” (8.3cm).

• Walk at a steady pace. Overlap the cutting rows.

Do not let the grass get too tall. If the grass gets

too long, start at the highest cutting position and

work down to the desired cutting height.

WARNING: If you strike a foreign object, stop the

motor and remove the battery. Thoroughly inspect the

mower for any damage. Repair any damage before

operating the mower. Excessive vibration of the

mower during operation is an indication of damage.

Thoroughly inspect the mower and repair any damage

before operating the mower.

EMPTYING THE GRASS CATCHER

See figure 10

• Stop mower and allow blades to completely stop.

• Open battery cover.

• Remove switch key and battery pack.

• Lift the rear discharge door.

• Lift the grass catcher by its handle to remove from

mower.

• Empty grass clippings.

• Lift the rear discharge door and reinstall the grass

catcher as described earlier in this manual.

• Reinstall switch key and battery pack when you

are ready to mow.

Fig. 9 Fig. 10

12

Model 62162S

13

Model 62162S

CHARGING THE BATTERY PACK

Charge the battery pack only with the charger provided.

Allow at least 90 minutes of charge time for 2.5Ah battery or

140 minutes of charge time for 4Ah battery or 180 minutes of

charge time for 5Ah battery before initial use of the mower.

Make sure the power supply is normal household voltage,

120 volts, 60Hz, AC only.

The battery charger should be operated in temperatures

between 39 and 104 degrees F (4 °C and 40 °C).

The battery should be charged in a cool, dry place.

2 to 3 initial charging/discharging cycles may be required to

achieve maximum run time/capacity.

DO NOT attempt to open the charger or the unit. There are

no customer serviceable parts inside. Call customer service

helpline at 1-800-618-7474 for assistance.

DO NOT incinerate battery packs even if they are severely

damaged or completely worn out. They can explode in a fire

causing injury.

DO NOT charge appliance in rain, or in wet locations.

Use the battery charger indoors only.

Disconnect charger from the power supply when not in use to

prevent damage to the charger during a power surge.

When fully charged, the battery can be safely stored in

temperatures down to -4 degrees F (-20 degrees C) for a

period of up to four weeks, before requiring charging. Fully

charge battery pack every 90 days.

If over a period of time the battery pack quickly runs down

after a full 90, 140 or 180 minutes charging period,

a replacement battery pack is needed.

To prevent permanent damage to the battery, never store in

a discharged condition.

WINTER STORAGE - Fully recharge before storage and

then again every 90 days.

Since the battery will not develop a memory, it does not

have to be fully discharged before recharging.

A small leakage of liquid from the battery cells may occur

under extreme usage, charging or temperature conditions.

This does not indicate a failure. However, if the outer seal is

broken and this leakage gets on your skin.

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or

vinegar.

c. If the battery liquid gets in your eyes, flush them with

clean water for a minimum of 10 minutes and seek

immediate medical attention.

Battery

Pack

The RBRC seal on the Li-Ion battery pack indicates that the cost to recycle the battery pack at the end of its useful life has

already been paid by The Great States Corporation/American Lawn Mower Company. It is illegal to place spent Li-Ion batteries

in the local municipal solid waste or in the trash. RBRC in cooperation with The Great States Corporation/American Lawn Mower

Company has provided an environmentally friendly and easy way to recycle spent Li-Ion batteries. Just contact your local

recycling center or call 1.800.8.BATTERY for information on where to drop off the spent battery.

TO CHARGE - SEE CHARGER MANUAL FOR COMPLETE INSTRUCTIONS

BATTERY DISPOSAL

Remove the battery pack from the tool, cover the terminals with heavy duty adhesive tape. Do not attempt to destroy or

disassemble battery pack or remove any components. This product contains lithium-ion batteries which must be recycled or

disposed of properly. Local, state or federal laws may prohibit disposal of these batteries in the municipal solid waste or rural

trash pick up systems.

Constant Red + Flash Green = Battery is charging

Constant Red + Constant Green = Battery is fully charged

Charger

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

DANGER:

Before performing any maintenance, make sure the

battery is removed from the battery compartment and the

switch key is removed. Failure to heed this warning could

result in serious personal injury.

WARNING:

Do not at any time let brake fluids, gasoline,

petroleum-based products, penetrating oils, etc., come

in contact with plastic parts. Chemicals can damage,

weaken, or destroy plastic which may result in serious

personal injury.

WARNING:

Always protect hands by wearing heavy gloves and/or

wrapping the cutting edges of the blade with rags and

other material when performing blade maintenance.

Failure to heed this warning could result in serious

personal injury.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types

of commercial solvents and may be damaged by their

use. Use clean cloths to remove dirt, dust, oil, grease,

etc.

WARNING:

Always wear safety goggles or safety glasses with side

shields during power tool operation or when blowing

dust. If environment is dusty, also wear a dust mask.

REPLACING THE CUTTING BLADE

See figures 11

NOTES: Only use identical replacement blades.

• Stop the motor and remove the switch key. Allow the

blade to come to a complete stop. Remove battery

from the battery compartment.

• Turn the mower on its side

• Wedge a block of wood between the blade and mower

deck to prevent the blade from turning.

• Loosen the blade nut (1) using a wrench or socket

(not provided). Turn the nut COUNTERCLOCK WISE

to loosen it.

• Remove the blade nut (1), spacer (2), blade insulator

(3), and blade (4).

• To re-install the blade, position the blade with the

cutting edges toward the ground. Replace the blade

insulator and spacer, then thread the blade nut on the

shaft and finger tighten.

NOTE: Make certain all parts are replaced in the exact

order in which they were removed. When installing

the cutting blade, verify that it is installed with the curved

ends pointing toward the mower deck, and not toward the

ground.

• Torque the blade nut down CLOCKWISE using a

torque wrench (not provided) to ensure the bolt is

properly tightened. The recommended torque for the

blade nut is 350-400 in. lbs.

Periodically check all nuts and bolts for proper

tightness to ensure safe operation of the mower.

Remove any buildup of grass and leaves on or around

the motor cover. Wipe the mower clean with a dry cloth

occasionally. Do not use water.

LUBRICATION

All of the bearings in this product are lubricated with a

sufficient amount of high grade lubricant for the life of

the unit under normal operating conditions. Therefore,

no further bearing lubrication is required.

At the beginning and end of each mowing season:

• Lubricate the springs on the rear discharge door

with light oil.

• Lubricate the height adjustment lever and related

hardware with light oil.

• Remove the wheels and lubricate the surface of

the axle bolt and the inner surface of the wheel

with light oil.

• Remove the blade and blade hub assembly and

lubricate the motor shaft with light oil or engine oil.

See Replacing the Cutting Blade for instructions

on removing the blade.

MAINTENANCE

1

2

3

4

14

Model 62162S

Fig. 11

SHARPENING THE BLADE

See Figure 12

For best mowing performance, the mower blade must

be kept sharp. A dull blade does not cut grass evenly

and overloads the motor. Under normal circumstances,

sharpening the blade twice during the mowing season

is usually sufficient. However, if your lawn has sandy

soil, more frequent sharpening's may be required.

• Following the instructions in the Replacing the

Cutting Blade section, remove the mower blade.

DO NOT attempt to sharpen the blade while it is

attached to the mower.

• Using a fine tooth file or stone, sharpen cutting

edges on both ends of the blade, removing equal

amounts of material from both ends.

BALANCING THE BLADE

See Figure 13

When sharpening, care should be taken to keep the

blade balanced. An unbalanced blade will cause

excessive vibration when the mower is running. This

vibration will eventually cause damage to the mower,

especially the motor.

To check blade balance:

• Clamp a screwdriver horizontally in a vise as

shown.

NOTE: If a vise is not available, a straight nail can also

be used.

• Place the center hole of blade on the screwdriver

(or nail) shank.

WARNING:

When removing, inspect the blade carefully. If blade is bent

or damaged, replace immediately with a new blade. Failure

to replace a bent or damaged blade could cause an accident

resulting in possible serious injury.

BATTERY MAINTENANCE

It is recommended to charge the mower every 3

months for optimum performance when not in use. If

the battery has been in storage for a long time without

recharging, it will be in a low charge state.

MAINTENANCE

• If blade is balanced, it will remain in a horizontal

position. If either end of the blade drops downward,

sharpen the heavy side until the blade is balanced.

REPLACING WHEELS

See Figure 14

To Replace a wheel:

• Stop the motor and remove the switch key. Remove

battery from the battery compartment.

• Turn the mower on its side.

• Using a flat blade screwdriver, pry off the hubcap (1).

• Remove the self-locking nut (2) from the wheel axle (3),

then remove the wheel (4).

• Replace with new wheel and install new self-locking nut

(2) securely.

• Replace hubcap (1).

Fig. 12

Fig. 13

15

Model 62162S

1

2

3

4

Fig. 14

STORING THE MOWER

• Remove the switch key and battery, and store in a secure

location out of the reach of children.

• Before storage, wipe any dirt or debris from the battery

area.

• Turn mower on its side and clean grass clippings that have

accumulated on the underside of the mower deck.

• Wipe the mower clean with a dry cloth.

• Check all nuts, bolts, knobs, screws, fasteners, etc., for

tightness.

• Inspect moving parts for damage, breakage and wear. Have

repairs made on any damaged or missing parts.

• Store mower indoors in a clean, dry place out of the reach of

children.

• Do not store near corrosive materials such as fertilizer or

rock salt.

To store the mower in a horizontal position:

See Figure 15

• Pull the T-Knobs (3) on the sides of the lower handles (1)

and turn 90 degree.

• Gently pivot the lower handles (1) toward the front of the

mower.

• Fully loosen the cam lock knobs (2) on the sides of the

handle and fold the upper handle down, making sure not to

bend or kink the power cord.

To store the mower in a vertical position:

See Figure 15-16

• Remove the grass catcher.

• Pull the T-Knobs (3) out on the sides of the lower handles

(1) and turn 90 degree.

• Gently pivot the lower handles (1) toward the front of the

mower; turn the T-knobs (3) 90 degree back and continue to

pivot the handle (1) until you hear and feel the lock pin

engaged in the locked storage position.

WARNING:

USE EXTREME CAUTION WHEN FOLDING THE HANDLE.

THE CORD CAN BE DAMAGED IF PINCHED BETWEEN

HANDLE SECTIONS CREATING A SAFETY HAZARD.

MAINTENANCE

• The upper handle can be stored either raised or lowered

when storing in the vertical position.

• To lower the upper handle, fully loosen the cam lock

knobs (2) on the sides of the handle and fold the upper

handle down, making sure not to bend or kink the power

cord.

NOTE: Make sure the pins on the handle adjustment knobs

are fully seated in the locking holes before attempting to raise

the mower to the standing position.

3

1

2

Fig. 15

16

Model 62162S

Fig. 16

WARNING:

WHEN THE HANDLE IS FOLDED, DO NOT ATTEMPT TO

START THE MOWER. WHEN STORING THE MOWER IN

THE VERTICAL POSITION, POSITION THE MOWER SO

THAT THE BLADE IS FACING A WALL. FAILURE TO

HEED THESE WARNINGS CAN LEAD TO SERIOUS

PERSONAL INJURY.

WARNING:

IF THE MOWER TIPS OVER FROM THE UPRIGHT

POSITION, MOWER DAMAGE OR PERSONAL INJURY

MAY RESULT. ALWAYS KEEP THE MOWER STABLE

AND OUT OF THE REACH OF CHILDREN WHEN IT IS IN

THE UPRIGHT POSITION. IF POSSIBLE, LAY IT FLAT

FOR STORAGE.

TROUBLESHOOTING

17

Model 62162S

Problem Possible cause Solution

The mower fails to start The safety key is not inserted in the slot.

The battery pack is depleted.

The battery pack is not attached to the

mower.

The battery pack is on the wrong side.

Battery or mower circuitry is too hot.

The handle is not set at one of the

operating positions.

Mower deck is clogged with grass and

debris.

Insert the safety key.

Charge the battery pack.

Attach the battery pack to the mower.

Move the battery pack to the correct side of

the battery compartment.

Allow the battery pack or mower to cool down.

Adjust the handle to the one of the operating

positions.

Clean the mower deck and make certain that

the blade has freedom of movement.

The mower cuts unevenly. Dull blade.

The cutting height is not set properly.

The blade is assembled incorrectly.

Sharpen or replace blade.

Raise the blade to a higher setting.

Reassemble the blade, following the section

"Replacing the Cutting Blade" in this manual.

Mower stops while

mowing.

The battery pack is depleted.

Mower is in overload condition.

Mower deck is clogged with grass and

debris.

Battery or mower circuitry is too hot.

Charge the battery pack.

Raise cutting height or slow down the mowing.

Unclog mower deck. Raise cutting height, or

cut a narrow swath.

Allow the battery pack or mower to cool down.

Mower does not mulch

properly.

Wet grass clippings are sticking to the

underside of the deck.

Mulching plug is missing.

The mower is set to cut too much grass.

Wait until the grass dries before mowing.

Install the mulching plug.

Raise the blade to a higher setting.

Excessive vibration Cutting blade is loose.

Cutting blade is unbalanced.

Bent cutting blade.

Bent motor shaft.

Tighten the blade bolt.

Balance the blade following the instructions.

Replace the blade.

Contact the service center at 1-800-618-7474.

Handle not in position Carriage bolts not seated properly.

Handle knobs not tightened.

Adjust the height of the handle and make sure

the carriage bolts are seated properly.

Tighten handle knobs.

18

Model 62162S

PARTS AND SERVICE

For parts or service, please call 1-800-618-7474 or visit us online at

scotts.americanlawnmower.com. Be sure to provide all relevant information when you

call or visit.

REPAIR PARTS (KITS/ ITEMS)

The model number of this tool is found on a plate or label attached to the housing.

Please record the serial number in the space provided below.

MODEL NUMBER___62162S _____

SERIAL NUMBER_______________

Always mention the model number when ordering kits/items for this tool.

No. Kit/ Item Number Description

1 LM62-HDW-1 Handle Hardware Kit

2 LM62-FWK-2 Front Wheel Kit

3 LM62-RWK-2 Rear Wheel Kit

4 LM62-HA-1 Wheel Height Adjuster Kit

5 LM62-BK-1 Mower Blade Kit

6 LM62-RDK-1 Rear Door Kit

7 LM62-SDD-1 Side Discharge Flap

8 LM62-SDC-1 Side Discharge Chute

9 LM62-MP-1 Mulching Plug Kit

10 LM62-KEY-1 Switch Key Kit

11 LM62-GC-1 Grass Catcher Kit

12 LM62-RFK-1 Rear flap Kit

13 BL86250 62V 5.0Ah Battery

14 CHL86200 62V Charger

CALL US FIRST !!

Call us first with questions about operating or maintaining your product

at 1.800.618.7474 between 8:00 a.m. – 5:00 p.m. Eastern Standard Time,

or get assistance on scotts.americanlawnmower.com.

NOTES

19

Model 62162S

____________________________________________________________________

Rev. 12/08/18

American Lawn Mower Company

The Great States Corporation

7444 Shadeland Station Way

Indianapolis, IN 46256, USA

Phone 1-800-618-7474

scotts.americanlawnmower.com

OWNER’S MANUAL

21 in. - 62 VOLT LITHIUM-ION CORDLESS MOWER

5.0Ah Lithium-ion Battery

Model 62162S

• 5 Year limited warranty on all Scotts 62V lithium ion power tools from date of purchase when used for personal, household, or family use.

• 3 Year limited warranty on all Scotts 62V lithium ion batteries and chargers from date of purchase when used for personal, household, or

family use.

The Great States Corp. (GSC) warrants to the original owner that this Scotts product and service part is free from defects in materials and

workmanship and agrees to repair or replace any defective product or part for the warranty period as stated above.

• Warranty voided if used for commercial or industrial purposes or any other improper use as determined by GSC.

• Warranty does not include repairs necessary due to operator’s abuse or negligence (including overloading the product beyond capacity or

immersion in water), or the failure to assemble, operate, maintain or store the product according to the instructions in the owner’s manual.

• This warranty does not cover

 Wear items, including but not limited to - drive belts & gears, tines, cutting blades, mower blades, saw chains, mulching blades,

blower fans, spool covers, trimmer line, blower and vacuum tubes, guide bars, high pressure hoses, wheels, handles, augers, worn

bags, power cables, and other items subject to wear over time.

 Wear on batteries, including but not limited to – drops, wear and breakage on charger, exposure to extreme temperature swings (hot

or cold), battery left on charger too long, battery left uncharged for too long, and misuse or abuse of the battery.

• This warranty does not cover damage caused by cold, heat, rain, excessive humidity or other environmental extremes.

• This warranty does not cover normal deterioration of the exterior finish or normal wear and tear on the products including, but not limited to

scratches, cracks, dents, or damage caused by outside chemicals.

• This warranty is not transferable and only applies to new products sold directly from an authorized retailer. This warranty does not apply to any

product, new or used, purchased through unauthorized third-party channels. For information on authorized dealers, contact our customer

support hotline at 1-800-618-7474 (Mon-Fri 8am-5pm Est)

• Any incidental, indirect or consequential loss, damage, or expense that may result from any defect or malfunction of the products is not covered

by the warranty.

• The warranty does not include installation, assembly or normal adjustments explained in the owner‘s manual. The expense of delivering the

product to the vendor and the expense of returning the product or replacement parts to the owner is not covered by the warranty.

Additional Warranty Limitations

Some states do not allow the exclusion or limitation on how long an implied warranty lasts, so the above limitation may not apply to you. Products

sold damaged or incomplete, sold ―as is, or sold as reconditioned are not covered under the warranty.

Damage or liability caused by shipping, improper handling, improper assembly, incorrect voltage, improper wiring, improper maintenance, improper

modification or the use of accessories and/or attachments not specifically recommended is not covered by this warranty.

Proof of purchase, original dated sales receipt, must accompany all warranty claims.

For claims go to scotts.americanlawnmower.com or call our customer support hotline from 8am-5pm EST, Mon-Fri at

1-800-618-7474

WARRANTY POLICY

Scotts Warranty policy

In a continued commitment to improve quality, the Manufacturer reserves the right to make

component changes or design changes when necessary.

La page charge ...

Scotts 62162S Le manuel du propriétaire

Scotts 62162S Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents