Twin-Star International 23DM2126 Manuel utilisateur

Marque: Twin-Star International

Modèle: 23DM2126

Catégorie: Cheminées

Taper: Manuel utilisateur

ATTENTION

IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL

OR CALL CUSTOMER SERVICE BEFORE YOU RETURN

THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED.

For Customer Service: www.twinstarhome.com

in English Call: 866-661-1218

in Spanish Call: 866-661-1218

in French Call: 866-374-9203

ATENCIÓN

SI TIENE ALGÚN PROBLEMA O PREGUNTAS,

ENVÍE UN MENSAJE DE CORREO ELECTRÓNICO O LLAME AL SERVICIO

DE ATENCIÓN AL CLIENTE ANTES DE DEVOLVER

ESTE PRODUCTO A LA TIENDA EN LA QUE LO COMPRÓ.

Servicio de atención al cliente: www.twinstarhome.com

Línea para llamadas en inglés: 866-661-1218

Línea para llamadas en español: 866-661-1218

Línea para llamadas en francés: 866-374-9203

STOP

PARE

ATTENTION

POUR TOUT PROBLÈME OU TOUTE QUESTION,

ENVOYEZ UN COURRIEL AU SERVICE À LA CLIENTÈLE OU APPELEZ LE

SERVICE À LA CLIENTÈLE AVANT DE RETOURNER

CE PRODUIT OÙ VOUS L’AVEZ ACHETÉ.

Pour le service à la clientèle : www.twinstarhome.com

Pour appeler en anglais, composez le 866-661-1218

Pour appeler en espagnol, composez le 866-661-1218

Pour appeler en français, composez le 866-374-9203

STOP

INSTRUCTION MANUAL ENCLOSED

MANUEL D'INSTRUCTIONS À L’INTÉRIEUR

MANUAL DE INSTRUCCIONES ADJUNTO

INSTRUCTION MANUAL ENCLOSED

MANUEL D'INSTRUCTIONS À L’INTÉRIEUR

MANUAL DE INSTRUCCIONES ADJUNTO

)-XOBLQGG 

ELECTRIC FIREPLACE

23DM2126

INSTRUCTION MANUAL

www.twinstarhome.com

In English call: 866-661-1218

In French call: 866-374-9203

In Spanish call: 866-661-1218

For Customer Service:

Twin-Star International, Inc.

Delray Beach, FL 33445

Made in China

Printed in China

Important Information ........................................................................................................................... 2

Product Speciﬁ cations ......................................................................................................................... 3

Package Contents ................................................................................................................................ 4

Hardware Contents............................................................................................................................... 5

Safety Information ................................................................................................................................ 5

Preparation ........................................................................................................................................... 6

Assembly instructions ........................................................................................................................... 6

Operating Instructions .......................................................................................................................... 9

Care and Maintenance ........................................................................................................................1 1

Troubleshooting ...................................................................................................................................1 1

Warranty ............................................................................................................................................. 1 2

Replacement Parts ............................................................................................................................. 1 3

TABLE OF CONTENTS

Wall Mantel

Corner Mantel

Please read and understand this entire manual before attempting to assemble, operate or install

the product. If you have any question regarding the product, please call customer service at

1-866-661-1218, 8 a.m.-8 p.m., EST, Monday-Friday.

When using electrical appliances, always follow basic precautions to reduce the risk of ﬁ re,

electrical shock, and injury to persons including the following:

1. Read all instructions before using this appliance.

2. This appliance is hot when in use. To avoid burns, do not touch hot surfaces with bare skin.

If provided, use handles when moving this appliance. Keep combustible materials, such as furniture,

pillows, bedding, papers, clothes and curtains at least 3 ft. (0.9 m) from the front of this appliance.

WARNING: In order to avoid overheating, do not cover the heater.

WARNING: Use extreme caution when operating heater near children and the disabled.

3. The appliance is not to be used by children or persons with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision

or instruction.

4. This appliance is not a toy. Supervise children playing near it.

5. If possible, always unplug this appliance when not in use.

6. Do not operate any heater with a damaged cord or plug, after the appliance malfunctions, or if it has

been dropped or damaged in any manner.

7. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualiﬁ ed persons in order to avoid a hazard.

8. Only a qualiﬁ ed service person should repair this product.

9. Under no circumstances should this ﬁ replace be modiﬁ ed. Parts having to be removed for servicing

must be replaced prior to operating this ﬁ replace again.

10. Do not use outdoors.

11. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never

locate this appliance where it may fall into a bathtub or other water container.

12. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord

away from trafﬁ c areas and where it will not be tripped over.

13. To disconnect this appliance, turn controls to the off position, and then remove plug from outlet.

14. Connect to properly grounded outlets only.

15. This appliance, when installed, must be electrically grounded in accordance with local codes or, in

the absence of local codes, with the current CSA C22.1 Canadian Electrical Code or for U.S.A.

installations, follow local codes and the National Electrical Code, ANSI/NFPA NO.70.

16. The heater must not be located immediately below a socket-outlet.

17. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause

an electric shock or ﬁ re, or damage the appliance.

18. To prevent a possible ﬁ re, do not block air intakes or exhaust in any manner. Do not use on soft

surfaces, like a bed, where opening may become blocked.

19. This appliance has hot and arcing or sparking parts inside. Do not use it in areas where gasoline,

paint or ﬂ ammable liquids are used or stored. This ﬁ replace should not be used as a drying rack for

clothing. Do not hang Christmas stockings or other decorations on or near this product.

20. Use this appliance only as described in the manual. Any other use not recommended by the

manufacturer may cause ﬁ re, electric shock or injury to persons.

21. There is a thermostat limiter inside the heater. When inner temperature overheating or abnormal

heating occurs, the thermostat protective device will cutoff the power supply to avoid damage to the

ﬁ replace or risk of ﬁ re.

IMPORTANT INFORMATION

22. Avoid the use of an extension cord because the extension cord may overheat and cause risk of ﬁ re.

However, if you have to use an extension cord, the cord must be No.14 AWG minimum size and rated

not less than 1875 watts. The extension cord must be a three-wire cord with grounding type plug and

cord connection. The extension cord shall not be more than 20 ft. (6 m) in length.

23. See directions in Figure 1. This heater is for use on 120 volts. The cord has a plug as shown in

ﬁgure 1. See Figure 1 for grounding instruction. An adapter as shown at C is available for

connecting three-blade grounding type plugs to two-slot receptacles. The green grounding plug

extending from the adapter must be connected to a permanet ground such as a properly

gounnded outlet box. The adapter should not be used if a three-slot grounded receptacle is

available.

C D

Grounding Pin

Fig. 1

IMPORTANT INFORMATION

Metal

Screws

Grounding

Means

SAVE THESE

INSTRUCTIONS

PRODUCT SPECIFICATIONS

VOLTAGE 120 V, 60 Hz

AMPS (with heater) 11.7 Amps

AMPS (without heater) < 0.1 Amps

WATTS (with heater) 1400 Watts

WATTS (without heater) < 10 Watts

Part Description Quantity

A Hearth/Base 1

B Left Front Panel 1

C Right Front Panel 1

D Center Front Panel 1

E Left Side Panel 1

F Right Side Panel 1

G Mantel/Top 1

H Center Top Panel 1

I Top Corner Extension 1

J “L” Corner Brace 1

K Insert 1

PACKAGE CONTENTS

HARDWARE CONTENTS

Part

Description

Bolt

Washer

Wood Dowel

Quantity

Picture

(Shown to size)

SAFETY INFORMATION

WARNING

• Before assembly, carefully use scissors or utility knife to cut and unwrap all parts.

Make sure you do not discard the hardware.

CAUTION

• Use care in assembling your new ﬁreplace. Take your time and use the hardware

provided and a quality Phillips head screwdriver. Never overtighten bolts.

• Do not sit on any part of the mantel.

• All panels are labeled left and right as viewed from the front of unit.

Touch-up Pen

Model No. W3352

W3352

WARNING

To avoid injury from unexpected starting or electrical shock, do not plug the power cord into a

source of power during unpacking and assembly. The cord must remain unplugged whenever

you are adjusting/assembling the ﬁ replace.

If any part is missing or damaged, do not attempt to use or plug in the power cord until the

missing or damaged part is correctly replaced. To avoid electric shock, use only identical

replacement parts when servicing double-insulated tools.

ASSEMBLY INSTRUCTIONS

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts

with package contents list and diagram above. If any part is missing or damaged, do not

attempt to assemble, install or operate the product. Contact customer service for

replacement parts.

Estimated Assembly Time: 60 Minutes

Tools Required for Assembly (not included): Phillips head screwdriver, scissors

and utility knife

Fig. 1

2. Locate Center Top Panel (H), insert one Wood

Dowel (CC) into each of the pre-drilled holes.

Attach the Center Top Panel to the completed

assembly from step 1. Then use Bolts (AA) and

Washers (BB) through the pre-drilled holes in the

mounting blocks.

HAND TIGHTEN ONLY.

1. Locate the Center Front Panel (D), Right Front

Panel (C) and Left Front Panel (B) and set out face

down on a scratch-free surface.

Insert one Wood Dowel (CC) into each of the

pre-drilled holes.

Push the Right Front Panel and Left Front Panel

snug to the Center Panel. Make sure the Wood

Dowels are seated in the pre-drilled holes. Insert

Bolts (AA) and Washers (BB) into the holes in the

mounting blocks.

HAND TIGHTEN ONLY.

Hardware Used

Bolt

1/4 in. x 1-1/4 in.

Bolt

1/4 in. x 1-1/4 in.

x 2

Washer

1/4 in. x 3/4 in.

Washer

1/4 in. x 3/4 in.

x 2

Wood Dowel

x 2

x 4

Fig. 2

Fig. 3

Fig. 4

3. Locate Hearth/Base (A) and set out ﬁnished side up

on the ﬂoor.

Insert one Wood Dowel (CC) into each of the

pre- drilled holes.

Attach the completed Front panel assembly from

step 2 to the Hearth/Base (A). Make sure the dowels

are seated into the pre-drilled holes in the

Hearth/Base. Using Bolts (AA) and Washers (BB)

attach panels through pre-drilled holes in the

mounting blocks.

HAND TIGHTEN ONLY.

5. Insert one Wood Dowel (CC) into each of the

pre-drilled holes on the top edges of the Assembly

from step 4. Then locate Mantel/Top (G) and lay

ﬁ nished side up on top of completed assembly.

From the inside, attach Mantel/Top (G) using Bolts

(AA) and Washers (BB) through the pre-drilled holes

in the mounting blocks.

HAND TIGHTEN ONLY.

Using Phillips head screwdriver tighten all Bolts

alternating top and bottom, left and right.

Hardware Used

Bolt

1/4 in. x 1-1/4 in.

Bolt

1/4 in. x 1-1/4 in.

Bolt

1/4 in. x 1-1/4 in.

x 6

x 10

x 2

Washer

1/4 in. x 3/4 in.

Washer

1/4 in. x 3/4 in.

Washer

1/4 in. x 3/4 in.

x 6

x 10

x 2

Wood Dowel

x 4

4. Locate Left Side Panel (E) and Right Side Panel (F),

insert one Wood Dowel (CC) into each of the

pre-drilled holes. Attach to the completed front panel

assembly and Hearth/Base use Bolts (AA) and

Washers (BB) through the pre-drilled holes in the

mounting blocks.

HAND TIGHTEN ONLY.

Fig. 5

Fig. 6

Fig. 7

7. Locate the “L” Corner Brace (J), Top Corner

Extension (I) and set out face down on a

scratch-free surface. Insert one Wood Dowel (CC)

into each of the pre-drilled holes. Attach the “L”

Brace snug to Top Corner Extension (I), insert Bolts

(AA) and Washers (BB) into the holes in the

mounting blocks.

HAND TIGHTEN ONLY.

8. Insert one Wood Dowel (CC) into each of the

pre- drilled holes. Carefully slide the Complete

assembly from step 7 into place at back of Mantel.

Then use Bolts (AA) and Washers (BB) through the

pre-drillled holes in the mounting blocks.

HAND TIGHTEN ONLY.

Now you may tighten down all the bolts holding the

Corner Back assembly. Be careful not to over

tighten.

Completed

Unit

Electric

Fireplace Insert

Install

Insert

From

Back

Hardware Used

Bolt

1/4 in. x 1-1/4 in.

Bolt

1/4 in. x 1-1/4 in.

x 1

x 4

Washer

1/4 in. x 3/4 in.

Washer

1/4 in. x 3/4 in.

x 1

x 4

Wood Dowel

x 2

6. Remove the two mounting brackets attached to the

back of the Left and Right Front panels. Set aside

with the wood screws.

PLEASE READ ALL “ELECTRIC FIREPLACE

INSERT” INSTRUCTIONS PRIOR TO INSTALLING

ELECTRIC INSERT IN YOUR COMPLETED

FIREPLACE MANTEL. INSTALL THE INSERT IN

YOUR FIREPLACE CLOSE TO ITS FINAL

POSITION.

Lift insert carefully into the back of the unit and

center in the insert opening. Do not drag insert

across Hearth/Base (A) as it may scratch your unit.

Install the mounting brackets to hold insert ﬂ ush

against the inside of the mantel front panel.

MOVE YOUR COMPLETED UNIT ONLY SHORT

DISTANCES. MOVE COMPLETED UNIT WITH

GREAT CARE. IT TAKES TWO PEOPLE TO MOVE

COMPLETED UNIT INTO ITS FINAL POSITION.

OPERATING INSTRUCTIONS

Control panel can be accessed at upper-right corner of insert (K).

- POWER

The power button supplies power to all of the functions of the ﬁ replace. The power button will put the

insert in a standby mode. This will turn off all functions at once but will hold the settings in the memory.

By pressing the power button again the unit will turn on at the same settings.

NOTE: Holding the power button on the control panel for 10 seconds will disable the heater function.

- FLAME

Each time the ﬂ ame button is pressed, the intensity of the ﬂ ame decreases. There are 6 brightness levels

you can cycle through, including the OFF setting.

- HEATER

Your ﬁ replace consists of a fan-forced wire-element-type heater. There are 11 thermostat levels you can

cycle through, including the OFF and ON settings.

This button on the remote control only turns ON and OFF heater function.

NOTE: To change between °F and °C press and hold the heater button on the control panel for

10 seconds.

- TIMER

Press the timer button to cycle through the 10 timer settings (30 minutes, 1 Hour, 2H, 3H, 4H, 5H, 6H,

7H, 8H and 9H) and the OFF setting.

Note: When a function is changed from the control

panel or remote control there will be a corresponding

indicator (see Figure 1) on the upper-right of the

projection screen. The indicator shows the function

changed and the level selected by the control panel or

remote control. When the function is turned off, the

corresponding indicator will ﬂ ash 5 times and then

fade off.

Fig . 1

When choosing a location for your new ﬁ replace, follow the general instructions. Also, for best effect,

install the ﬁ replace out of direct sunlight.

ELECTRICAL CONNECTION

A 15-Amp, 120-V, 60 Hz circuit with a properly grounded outlet is required. Preferably, the ﬁ replace will

be on a dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or

the fuse to blow when the heater is in operation. The unit comes standard with 6-ft. three-wire

cord, exiting from the rear of the ﬁ replace. Avoid using an extension cord. If an extension cord must be

used, it must be a minimum 14 AWG, three wire with grounding type plug connector and rated not less

than 1875 watts. The cord shall not be more than 20 ft. in length.

Cold climate installation recommendation: When installing this unit against a non-

insulated exterior wall or chase, it is mandatory that the outer walls be insulated to

conform to applicable insulation codes.

NOTE: PLEASE OPERATE REMOTE TRANSMITTER AT A SLOW MEASURED PACE. PRESS THE

REMOTE CONTROL BUTTONS WITH AN EVEN MOTION AND GENTLE PRESSURE. REPEATEDLY

PRESSING BUTTONS IN RAPID SUCCESSION MAY CAUSE THE TRANSMITTER TO

MALFUNCTION.

NOTE: This equipment has been tested and found to comply with the limits for Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation.

Modiﬁ cations not approved by the party responsible for compliance could void user’s authority to operate

the equipment.

This Class B digital apparatus complies with Canadian ICES-003.

REPLACING THE REMOTE CONTROL BATTERY

When the remote control stops operating or its range seems reduced, it is time to replace the battery with

new ones. Note: Batteries should be removed if the product is to be left unused for a long time.

1. The battery compartment is located on the back end of the remote.

2. Press and slide the battery door open and remove the old battery.

3. Insert 2 AAA batteries (not included), checking that the + and - sides of the battery match inside the

battery compartment.

4. Replace the battery compartment door.

DISPOSAL OF USED BATTERIES

Battery may contain hazardous substances which could be endangering to

enviroment and human health.

This symbol marked on the battery and/or packaging indicates that used battery shall

not be treated as municipal waste. Instead it shall be left at the appropriate collection

point for recycling.

By ensuring the used batteries are disposed of correctly, you will help preventing

potential negative consequences for the environment and human health. The recycling

of materials will help to converse natural resources.

For more information about collection and recycling of used batteries, please contact

your local municipality, your waste disposal service or the point of sale where you

purchased this point.

WARNING: Make sure the power is turned off before proceeding. Any electrical repairs

or rewiring of this unit should be carried out by a licensed electrician in accordance with

national and local codes.

If repairing or replacing any electrical component or wiring, the original wire routing,

color coding and securing locations must be followed.

• The motors used on the fan and the ﬂ ame generator assembly are pre-lubricated for extended bearing

life and require no further lubrication. However, we recommend periodic cleaning/vacuuming of the

fan/ heater.

• Make sure the unit is turned OFF and unplugged whenever you are cleaning the heater or ﬁ replace.

WARNING: Electrical outlet wiring must comply with local building codes and other

applicable regulations to reduce the risk of ﬁ re, electrical shock and injury to persons.

WARNING: Do not use this ﬁ replace if any part of it has been under water. Immediately

call a qualiﬁ ed service technician to inspect the ﬁ replace and replace any part of the

electrical system.

WARNING: Disconnect power before attempting any maintenance or cleaning to reduce

the risk of ﬁ re, electrical shock or personal injury.

WARNING: During any service of this appliance, the power to the unit must be turned off.

First turn the main power switch to the OFF position. Then remove the electrical plug from

the wall outlet.

CARE AND MAINTENANCE

• Dust your ﬁ replace regularly with a soft non-lint producing cloth or household

dusting product.

• Clean your ﬁ replace with a gentle non-abrasive household cleaner. Make sure

to dry your ﬁ replace immediately with a soft cloth or towel.

• Tips for using touch-up pen (ZZ): For scratches, stroke in direction of scratch. For worn areas,

stroke in direction of wood grain. Rub excess colorant promptly with a soft cloth.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

No power, logs do not glow. 1. Power cord was not

plugged in the outlet.

2. Main power switch is not

in “ON” position.

1. Check that unit is plugged into

a standard 120V outlet.

2. Press power button several

times, making sure power

is set at “ON” position.

Logs glow

, but no ﬂ

ame effect. Flame button is not in

“ON” position.

Press ﬂ ame button several times.

Heater does not blow warm air. The current room temperature

is higher than the temperature

setting.

Adjust the temperature settings

to ensure that the thermostat is

set higher than the current room

temperature.

Heater doesn’t work, but Power

and Heater settings are “ON”

and thermostat is set

(see solution above).

The product is on protected

status.

Turn all switches to the “OFF”

position and unplug the unit from

the wall outlet for 5 minutes. After

5 minutes plug the unit back into

wall outlet, and operate as normal.

Flame effect works but heater

function does not and the

emberbed ﬂ ashes when the

heater button is pressed.

Heater function is locked. Heater function is locked. Press

and hold the POWER button to

unlock the heater function.

1-YEAR LIMITED WARRANTY

The manufacturer warrants this product to be free from manufacturing and material defects for a period of

one year from date of purchase, subject to the following conditions and limitations.

1. Install and operate this Electric Fireplace in accordance with the installation and operating

instructions furnished with the product at all times. Any unauthorized repair, alteration, willful abuse,

accident, or misuse of the product shall nullify this warranty.

2. This warranty is non-transferable, and is made to the original owner, provided that the purchase was

made through an authorized supplier of the product.

3. The warranty is limited to the repair or replacement of part(s) found to be defective in material or

workmanship, provided that such part(s) have been subjected to normal conditions of use and

service, after said defect is conﬁ rmed by the manufacturer’s inspection.

4. The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by

refunding the wholesale price of the defective part(s).

5. Any installation, labor, construction, transportation, or other related costs/expenses arising from

defective part(s), repair, replacement, or otherwise of same, will not be covered by this warranty,

nor shall the manufacturer assume responsibility for same.

6. The owner/user assumes all other risks, if any, including the risk of any direct, indirect or

consequential loss or damage arising out of the use, or inability to use the product, except

as provided by law.

7. All other warranties – expressed or implied – with respect to the product, its components and

accessories, or any obligations/liabilities on the part of the manufacturer are hereby expressly

excluded.

8. The manufacturer neither assumes, nor authorizes any third party to assume on its behalf, any other

liabilities with respect to the sale of the product.

9. The warranties as outlined within this document do not apply to non accessories used in conjunction

with the installation of this product.

This warranty is void if:

a. The ﬁ replace is subjected to prolonged periods of dampness or condensation.

b. Any unauthorized alteration, willful abuse, accident, or misuse of the product.

c. You do not have the original receipt of purchase.

IF WARRANTY SERVICE IS NEEDED

Contact the manufacturer by calling customer service department at 1-866-661-1218,

8 a.m.-8 p.m., EST, Monday-Friday. Make sure you have your warranty, your sales receipt,

location of purchase and the model/serial number of your product.

Printed in China

REPLACEMENT PARTS LIST

For replacement parts, call our customer service department at 1-866-661-1218,

8 a.m.-8 p.m., EST, Monday-Friday.

Part Description

Part No.

23EF023SRA

Qty

A Heater/Blower Assembly Y07-C26-P01 1

B Main Circuit Board Y11-C53-P15 1

C Flame Generator Drive Motor Y07-P10Q 1

D Flame Generator/ Spinner Y10-S52-P011 1

E LCD Display Y10-C43-P70 1

F Front Projection Screen Y10-S52-P09 1

G Flame Circuit Board Y11-C53-P40 1

H Emberbed with log Y10-S52-P02 1

I Control Panel Circuit Board Y10-S52-P32 1

J Control Panel - 4 Buttons Y10-C43-P25 1

K Remote Control - 4 Buttons P71 1

REMOTE/REMOTO/

TÉLÉCOMMANDE

ATTENTION

IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL

OR CALL CUSTOMER SERVICE BEFORE YOU RETURN

THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED.

For Customer Service: www.twinstarhome.com

in English Call: 866-661-1218

in Spanish Call: 866-661-1218

in French Call: 866-374-9203

ATENCIÓN

SI TIENE ALGÚN PROBLEMA O PREGUNTAS,

ENVÍE UN MENSAJE DE CORREO ELECTRÓNICO O LLAME AL SERVICIO

DE ATENCIÓN AL CLIENTE ANTES DE DEVOLVER

ESTE PRODUCTO A LA TIENDA EN LA QUE LO COMPRÓ.

Servicio de atención al cliente: www.twinstarhome.com

Línea para llamadas en inglés: 866-661-1218

Línea para llamadas en español: 866-661-1218

Línea para llamadas en francés: 866-374-9203

STOP

PARE

ATTENTION

POUR TOUT PROBLÈME OU TOUTE QUESTION,

ENVOYEZ UN COURRIEL AU SERVICE À LA CLIENTÈLE OU APPELEZ LE

SERVICE À LA CLIENTÈLE AVANT DE RETOURNER

CE PRODUIT OÙ VOUS L’AVEZ ACHETÉ.

Pour le service à la clientèle : www.twinstarhome.com

Pour appeler en anglais, composez le 866-661-1218

Pour appeler en espagnol, composez le 866-661-1218

Pour appeler en français, composez le 866-374-9203

STOP

INSTRUCTION MANUAL ENCLOSED

MANUEL D'INSTRUCTIONS À L’INTÉRIEUR

MANUAL DE INSTRUCCIONES ADJUNTO

INSTRUCTION MANUAL ENCLOSED

MANUEL D'INSTRUCTIONS À L’INTÉRIEUR

MANUAL DE INSTRUCCIONES ADJUNTO

)-XOBLQGG 

Twin-Star International 23DM2126 Manuel utilisateur

Marque: Twin-Star International

Modèle: 23DM2126

Catégorie: Cheminées

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Twin-Star International 23DM2126 User manual

Twin-Star International 23DM2126 Manuel utilisateur

Twin-Star International 23DM2126 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents