Black & Decker BDCCS20B Manuel utilisateur

Catégorie
Scies circulaires
Taper
Manuel utilisateur
INSTRUCTION MANUAL
20V MAX* LI-ION 5-
1
/
2 INCH (140MM)
CIRCULAR SAW
Thank you for choosing BLACK+DECKER!
PLEASE READ BEFORE RETURNING THIS PRODUCT FOR
ANY REASON.
If you have a question or experience a problem with your BLACK+DECKER
purchase, go to http://www.blackanddecker.com/instantanswers
If you can’t find the answer or do not have access to the Internet, call
1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. - Fri. to speak with an agent.
Please have the catalog number available when you call.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
VEA EL ESPANOL EN LA CONTRAPORTADA.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
*Maximum initial battery pack voltage (measured without a workload) is 20 volts. Measured
under a workload, nominal voltage is 18.
CATALOG NUMBER
BDCCS20
To register your new product, call 1-800-544-6986
or visit www.BlackandDecker.com/NewOwner
2
GENERAL POWER TOOL SAFETY WARNINGS
WARNING: Read all safety warnings and all instructions.
Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a ground
fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the
risk of electric shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, nonskid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position
before connecting to power source and/ or battery pack, picking up
or carrying the tool. Carrying power tools with your finger on the switch or
energizing power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The information it contains
relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols
below are used to help you recognize this information.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION: Indicates a potentially haz ard ous situation which, if not avoided, may
result in minor or mod er ate injury.
NOTICE: Used without the safety alert symbol indicates potentially hazardous
situation which, if not avoided, may result in property damage.
3
e) Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or long
hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust
collection can reduce dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from
the power tool before making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits, etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified by the manufacturer. A charger that
is suitable for one type of battery pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically designated battery packs. Use of any
other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects like
paper clips, coins, keys, nails, screws, or other small metal objects that
can make a connection from one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery, avoid contact. If
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR ALL SAWS
DANGER: Keep hands away from cutting area and the blade. Keep your
second hand on auxiliary handle or motor housing. If both hands are holding the
saw, they cannot be cut by the blade.
b) Do not reach underneath the workpiece. The guard cannot protect you from the
blade below the workpiece.
c) Adjust the cutting depth to the thickness of the workpiece. Less than a full
tooth of the blade teeth should be visible below the workpiece.
d) Never hold piece being cut in your hands or across your leg. Secure the
workpiece to a stable platform. It is important to support the work properly to
minimize body exposure, blade binding, or loss of control.
e) Hold power tool by insulated gripping surfaces when performing an
operation where the cutting tool may contact hidden wiring. Contact with a
“live” wire will also make exposed metal parts of the power tool “live” and shock the
operator.
4
f) When ripping always use a rip fence or straight edge guide. This improves the
accuracy of cut and reduces the chance of blade binding.
g) Always use blades with correct size and shape (diamond versus round) of
arbour holes. Blades that do not match the mounting hardware of the saw will run
eccentrically, causing loss of control.
h) Never use damaged or incorrect blade washers or bolt. The blade washers
and bolt were specially designed for your saw, for optimum performance and safety
of operation.
CAUSES AND OPERATOR PREVENTION OF KICKBACK:

causing an uncontrolled saw to lift up and out of the workpiece toward the operator.

stalls and the motor reaction drives the unit rapidly back toward the operator.

the blade can dig into the top surface of the wood causing the blade to climb out of
the kerf and jump back toward the operator.

conditions and can be avoided by taking proper precautions as given below:
a) Maintain a firm grip with both hands on the saw and position your arms to
resist kickback forces. Position your body to either side of the blade, but not in
line with the blade. Kickback could cause the saw to jump backwards, but kickback
forces can be controlled by the operator, if proper precautions are taken.
b) When blade is binding, or when interrupting a cut for any reason, release
the trigger and hold the saw motionless in the material until the blade comes
to a complete stop. Never attempt to remove the saw from the work or pull the
saw backward while the blade is in motion or kickback may occur. Investigate
and take corrective actions to eliminate the cause of blade binding.
c) When restarting a saw in the workpiece, center the saw blade in the kerf and
check that saw teeth are not engaged into the material. If saw blade is binding, it
may walk up or kickback from the workpiece as the saw is restarted.
d) Support large panels to minimize the risk of blade pinching and kickback.
Large panels tend to sag under their own weight. Supports must be placed under the
panel on both sides, near the line of cut and near the edge of the panel.
e) Do not use dull or damaged blades. Unsharpened or improperly set blades
produce narrow kerf causing excessive friction, blade binding and kickback.
f) Blade depth and bevel adjusting locking knobs must be tight and secure before
making cut. If blade adjustment shifts while cutting, it may cause binding and kickback.
g) Use extra caution when sawing into existing walls or other blind areas. The
protruding blade may cut objects that can cause kickback.
LOWER GUARD SAFETY INSTRUCTIONS
a) Check lower guard for proper closing before each use. Do not operate the
saw if lower guard does not move freely and close instantly. Never clamp or tie
the lower guard into the open position. If saw is accidentally dropped, lower guard
may be bent. Raise the lower guard with the retracting handle and make sure it moves
freely and does not touch the blade or any other part, in all angles and depths of cut.
b) Check the operation of the lower guard spring. If the guard and the spring
are not operating properly, they must be serviced before use. Lower guard may
operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris.
c) Lower guard should be retracted manually only for special cuts such as
“plunge cuts” and “compound cuts.” Raise lower guard by retracting handle and
as soon as blade enters the material, the lower guard must be released. For all other
sawing, the lower guard should operate automatically.
d) Always observe that the lower guard is covering the blade before placing
saw down on bench or floor. An unprotected, coasting blade will cause the saw to
walk backwards, cutting whatever is in its path. Be aware of the time it takes for the
blade to stop after switch is released.
5
ADDITIONAL SAFETY INSTRUCTIONS
Use clamps or another practical way to secure and support the workpiece to
a stable platform. Holding the work by hand or against your body leaves it unstable
and may lead to loss of control.
Keep your body positioned to either side of the blade, but not in line with the
saw blade. KICKBACK could cause the saw to jump backwards (see Causes and
Operator Prevention of Kickback and KICKBACK).
Avoid cutting nails. Inspect for and remove all nails from lumber before cutting.
Always make sure nothing interferes with the movement of the lower blade guard.
Accessories must be rated for at least the speed recommended on the tool warning
label. Wheels and other accessories running over rated speed can fly apart and cause
injury. Accessory ratings must always be above tool speed as shown on tool nameplate.
Always make sure the saw is clean before using.
Stop using this saw and have it properly serviced if any unusual noise or abnormal
operation occurs.
Always be sure all components are mounted properly and securely before using tool.
Always handle the saw blade with care when mounting or removing it or when
removing the diamond knockout.
Always wait until the motor has reached full speed before starting a cut.
Always keep handles dry, clean and free of oil and grease. Hold the tool firmly with
both hands when in use.
Always be alert at all times, especially during repetitive, monotonous operations.
Always be sure of position of your hands relative to the blade.
Stay clear of end pieces that may fall after cutting off. They may be hot, sharp and/
or heavy. Serious personal injury may result.
Replace or repair damaged cords. Make sure your extension cord is in good
condition. Use only 3-wire extension cords that have 3-prong grounding-type plugs
and 3-pole receptacles that accept the tool’s plug.
An extension cord must have adequate wire size (AWG or American Wire
Gauge) for safety. The smaller the gauge number of the wire, the greater the
capacity of the cable, that is 16 gauge has more capacity than 18 gauge. An
undersized cord will cause a drop in line voltage resulting in loss of power and


following table shows the correct size to use depending on cord length and

gauge number, the heavier the cord.
Recommended Minimum Wire Size for Extension Cords
Total Length of Cord
25 ft. 50 ft. 75 ft. 100 ft. 125 ft. 150 ft. 175 ft.
7.6 m 15.2 m 22.9 m 30.5 m 38.1 m 45.7 m 53.3 m
Wire Size AWG
18 18 16 16 14 14 12
WARNING: Blades coast after turn off. Serious personal injury may result.
WARNING: ALWAYS wear proper personal hearing protection that
conforms to ANSI S12.6 (S3.19) during use. Under some conditions and duration
of use, noise from this product may contribute to hearing loss.
WARNING: ALWAYS use proper eye protection. All users and bystanders
must wear proper eye protection that conforms to ANSI Z87.1.
WARNING: ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT
safety glasses. Also use face or dust mask if cutting operation is dusty.
ALWAYS wear certified safety equipment:
ANSI Z87.1 eye protection (CAN/CSA Z94.3).
ANSI S12.6 (S3.19) hearing protection.
NIOSH/OSHA respiratory protection.
6
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known in the state of California to cause cancer,
birth defects or other reproductive harm. Some examples of these chemicals are:


Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing, grinding,
drilling, and other construction activities. Wear protective clothing and wash
exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or
lay on the skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause
serious and permanent respiratory or other injury. Always use NIOSH/OSHA
approved respiratory protection appropriate for the dust exposure. Direct particles
away from face and body. Always operate tool in well-ventilated area and provide
for proper dust removal. Use dust collection system wherever possible.
SYMBOLS

definitions are as follows:
V ..................volts A ...................amperes
Hz ................hertz W .................. watts
min ..............minutes
or AC .......alternating current
or DC ..direct current
n
o .................no load speed
................Class I Construction .................earthing terminal
(grounded)
.................safety alert symbol
................Class II Construction .../min or rpm ....revolutions or reciprocations
(double insulated) per minute
...........
Read instruction manual before use
................
Use proper respiratory protection
................Use proper eye protection .................
Use proper hearing protection
TO REDUCE THE RISK OF KICKBACK
 
 
 
causing a pinched blade.
 Fig. FFig. E)
will lead to blade pinching.
 
 figure H) and solidly supported and
balanced on a strong, stable and level work surface. Support the work so that the wide
portion of the saw shoe is on the portion of the material that doesn’t fall after the cut is
figure G )
 
 

 
pressure treated and freshly cut green lumber can heavily load the saw which can lead
to stalling. Push the saw slower when this occurs.
 
 
saw with the blade against the work or pushed forward into cut can lead to stalling or
sudden backward movement of saw.
 
 
 
7

start a new cut on the line.
 
workpiece as shown in (figure J).
 
the blade to dig into the material, climb out of the work and run back toward the operator.
 
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGERS
SAVE THESE INSTRUCTIONS: This manual contains important safety instructions
for battery chargers.

pack, and product using battery pack.
WARNING: Shock hazard.
CAUTION: Burn hazard. To reduce the risk of injury, charge only designated
BLACK+DECKER 20V MAX lithium batteries. Other types of batteries may burst
causing personal injury and damage.
CAUTION: Under certain conditions, with the charger plugged in to the power
supply, the charger can be shorted by foreign material. Foreign materials of a
conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup
of metallic particles should be kept away from charger cavities. Always unplug the
charger from the power supply when there is no battery pack in the cavity. Unplug
charger before attempting to clean.
WARNING:
DO NOT attempt to charge the battery pack with any chargers other than the ones
in this manual. The charger and battery pack are specifically designed to work together.
These chargers are not intended for any uses other than charging designated
BLACK+DECKER 20V MAX lithium rechargeable batteries. Any other uses may
result in risk of fire, electric shock or electrocution.
Do not expose charger to rain or snow.
Pull by plug rather than cord when disconnecting charger. This will reduce risk of
damage to electric plug and cord.
Make sure that cord is located so that it will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
Do not use an extension cord unless it is absolutely necessary. Use of improper
extension cord could result in risk of fire, electric shock, or electrocution.
An extension cord must have adequate wire size (AWG or American Wire Gauge)
for safety. The smaller the gauge number of the wire, the greater the capacity of the
cable, that is 16 gauge has more capacity than 18 gauge. When using more than one
extension to make up the total length, be sure each individual extension contains at
least the minimum wire size.
Do not place any object on top of charger or place the charger on a soft surface
that might block the ventilation slots and result in excessive internal heat. Place
the charger in a position away from any heat source. The charger is ventilated
through slots in the top and the bottom of the housing.
Do not operate charger with damaged cord or plug — have them replaced immediately.
Do not operate charger if it has received a sharp blow, been dropped, or
otherwise damaged in any way. Take it to an authorized service center.
Do not disassemble charger; take it to an authorized service center when service
or repair is required. Incorrect reassembly may result in a risk of electric shock,
electrocution or fire.
Disconnect the charger from the outlet before attempting any cleaning. This will
reduce the risk of electric shock. Removing the battery pack will not reduce this risk.
NEVER attempt to connect 2 chargers together.
The charger is designed to operate on standard household electrical power (120
Volts). Do not attempt to use it on any other voltage.
SAVE THESE INSTRUCTIONS
8
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY PACKS
WARNING: For safe operation, read this manual and manuals originally supplied
with tool before using the charger.
The battery pack is not fully charged out of the carton. Before using the battery pack
and charger, read the safety instructions below. Then follow charging procedures outlined.
READ ALL INSTRUCTIONS
Do not incinerate the battery pack even if it is severely damaged or is completely
worn out. The battery pack can explode in a fire. Toxic fumes and materials are
created when LI-ION battery packs are burned.
Do not charge or use battery in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting or removing the battery from the charger
may ignite the dust or fumes.
If battery contents come into contact with the skin, immediately wash area with
mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte
for LI-ION batteries is composed of a mixture of liquid organic carbonates and lithium
salts. For NI-CD batteries it is a 25-35% solution of potassium hydroxide.
Contents of opened battery cells may cause respiratory irritation. Provide fresh air.
If symptoms persist, seek medical attention.
WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.
Charge the battery packs only in BLACK+DECKER chargers.
 DO NOT splash or immerse in water or other liquids. This may cause premature cell failure.
Do not store or use the tool and battery pack in locations where the temperature may
reach or exceed 105°F (40˚C) (such as outside sheds or metal buildings in summer).
WARNING: Never attempt to open the battery pack for any reason. If battery pack
case is cracked or damaged, do not insert into charger. Do not crush, drop or damage
battery pack. Do not use a battery pack or charger that has received a sharp blow, been
dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer,
stepped on). Damaged battery packs should be returned to service center for recycling.
WARNING: Fire hazard. Do not store or carry battery so that metal objects can
contact exposed battery terminals. For example, do not place battery in aprons,
pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc.
Transporting batteries can possibly cause fires if the battery terminals inadvertently
come in contact with conductive materials such as keys, coins, hand tools and the
like. The US Department of Transportation Hazardous Material Regulations (HMR)
actually prohibit transporting batteries in commerce or on airplanes (i.e., packed in
suitcases and carry-on luggage) UNLESS they are properly protected from short circuits.
So when transporting individual batteries, make sure that the battery terminals are
protected and well insulated from materials that could contact them and cause a short
circuit. NOTE: Batteries should not be put in checked baggage.
STORAGE RECOMMENDATIONS
1. The best storage place is one that is cool and dry away from direct sunlight and

2. Long storage will not harm the battery pack or charger.
WALL MOUNTING
This charger is designed to be wall mountable or to sit upright on a table or work surface.
If wall mounting, locate charger within reach of an electrical outlet. Mount securely using


CHARGING PROCEDURE
BLACK+DECKER chargers are designed to charge BLACK+DECKER battery packs.
1. Plug the charger into an appropriate outlet before inserting the battery pack.
2. Insert the battery pack into the charger.
9


The pack is fully charged and may be used at this time or left on the charger.
Recharge discharged batteries as soon as possible after use or battery life may
be greatly diminished. For longest battery life, do not discharge batteries fully. It is
recommended that the batteries be recharged after each use.
CHARGER DIAGNOSTICS
This charger is designed to detect certain problems that can arise with the battery packs

BAD BATTERY

indicated on the label. If you see this bad battery blink pattern, do not continue to charge
the battery. Return it to a service center or a collection site for recycling.
HOT/COLD PACK DELAY


has normalized. After this happens, the charger automatically switches to the Pack
The light flashes in the
pattern indicated on the label.
LEAVING THE BATTERY IN THE CHARGER

The charger will keep the battery pack fresh and fully charged. This charger features

pack to allow it to function at peak capacity. Battery packs should be tuned up weekly
or whenever the battery no longer delivers the same amount of work. To use the

IMPORTANT CHARGING NOTES
1. Longest life and best performance can be obtained if the battery pack is charged


This is important and will prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to touch while charging. This
is a normal condition, and does not indicate a problem. To facilitate the cooling
of the battery pack after use, avoid placing the charger or battery pack in a warm
environment such as in a metal shed, or an uninsulated trailer.
3. If the battery pack does not charge properly:


when you turn out the lights.
c. Move charger and battery pack to a location where the surrounding air

d. If charging problems persist, take the tool, battery pack and charger to your
local service center.
4. The battery pack should be recharged when it fails to produce sufficient power on

conditions. Follow the charging procedure. You may also charge a partially used pack
whenever you desire with no adverse affect on the battery pack.
5. Foreign materials of a conductive nature such as, but not limited to, steel wool,
aluminum foil, or any buildup of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply when there is no battery
pack in the cavity. Unplug charger before attempting to clean.

WARNING: Shock hazard. Never
attempt to open the battery pack for any reason. If the plastic housing of the battery pack
breaks or cracks, return to a service center for recycling.
10
INTENDED USE

WARNING: 

and could increase the possibility of kickback.
 
 
 
 

ASSEMBLY/ADJUSTMENT SET-UP
WARNING: TO REDUCE THE RISK OF INJURY, ALWAYS REMOVE BATTERY
FROM SAW BEFORE ANY OF THE FOLLOWING ADJUSTMENT OPERATIONS.
FUNCTIONAL DESCRIPTION


3. Main handle
4. Secondary handle
5. Shoe
6. Upper guard
7. Saw blade
Figure A
8. Lower blade guard

10. Bevel adjustment knob




Lithium Ion Battery Pack and Charger
Description Catalog #
This product uses the battery and charger listed in the chart below.
 

 


 

1
2
3
4
5
A
6
7
8
10
11
12
9
11
INSTALLING AND REMOVING THE BATTERY
PACK FROM THE TOOL
WARNING: Make certain the lock-off button is
engaged to prevent switch actuation before
removing or installing battery.
: Insert battery pack into
tool as shown in figure C. Ensure battery pack is fully
seated and fully latched into position.
epress the battery
release button as shown in figure D and pull battery
pack out of tool.
SUPPORTING LARGE PANELS / SECURING
WORKPIECE
Support large panels to minimize the risk of blade
pinching and kickback. Large panels tend to sag under
their own weight as shown in figure E.
Supports must be placed under the panel on both
sides, near the line of cut and near the edge of the
figure F).
Never hold piece being cut in your hands or across
figure G).
Secure the workpiece to a stable platform as shown in
figure H. It is important to support the work properly to

E

Material bends on blade causing
heavy loads or kickback
C
D
F
Support work near cut
G
H
CUTTING DEPTH ADJUSTMENT - FIGURES I & J
The depth of cut should be set according to the
thickness of the workpiece.
 
as shown in figure I.
 Move the saw shoe into the desired position. The

 

shown in figure J.
 Tighten the knob to lock the saw shoe in place.
BEVEL ANGLE ADJUSTMENT - FIGURE K
This tool can be set to bevel angles between 0° and 50°.
 

 

 
saw shoe in place.
 
bevel angle of an actual cut on a scrap piece of material.
SHOE ADJUSTMENT FOR 90° CUTS

the blade is perpendicular to the shoe at 0° bevel setting.

 
 
 

 
 (inset figure K) so that the shoe will
stop at the proper angle. Retighten jam nut against
the shoe while holding adjustment screw in position.
 

scrap piece of material.
ATTACHING AND REMOVING THE BLADE - FIGURE L - M
 
figure L.
 

engages and the blade stops rotating.
NOTE: Blade wrench is stored on the saw as shown
in figure M.
 
NOTE:
clockwise. To tighten, turn counterclockwise.
NOTE: Never engage the blade lock while the saw is
running, or engage in an effort to stop the tool. Never
turn the tool on while the blade lock is engaged.
Serious damage to your saw will result.
LOWER BLADE GUARD
WARNING: Laceration Hazard. The lower
blade guard is a safety feature which reduces the
risk of serious personal injury. Never use the saw if
the lower guard is missing, damaged, mis-
assembled or not working properly. Do not rely on
the lower blade guard to protect you under all
circumstances. Your safety depends on following
all warnings and precautions as well as proper
operation of the saw. Check lower guard for proper
closing before each use as outlined in Additional
12
L
20
19
7
13
M
9
K
17
5
10
18b
18a
J
15
16
I
5
11
14
13
Safety Rules for Circular Saws. If the lower blade guard is missing or not working
properly, have the saw serviced before using. To assure product safety and
reliability, repair, maintenance and adjustment should be performed by an
authorized service center or other qualified service organization, always using
identical replacement parts.
WARNING: 
hard but brittle material. Foreign objects in the work piece such as wire or nails can cause
tips to crack or break. Only operate saw when proper saw blade guard is in place. Mount
blade securely in proper rotation before using, and always use a clean, sharp blade.
WARNING: To reduce the risk of injury, It is important to support the work
properly and to hold the saw firmly to prevent loss of control which could cause
personal injury. Figure H illustrates typical hand support.
OPERATING INSTRUCTIONS
WARNING: To reduce the risk of serious personal injury, read, understand and
follow all important safety warnings and instructions prior to using tool.
BLADE SELECTION
Your circular saw is designed for use with 5-1/2 inch (140 mm) diameter blades
that have a 3/8 inch (10 mm) diameter bore. Blades must be rated for 6000 RPM
operation (or higher). DO NOT use any abrasive wheels.
GENERAL CUTS
WARNING: To reduce the risk of injury, remove the battery, and follow all
assembly, adjustment and set up instructions.
Make sure lower guard operates. Select the proper blade for the material to be cut.
 
 
 
 
 
SWITCH

 

 
The tool will continue to run as long as the trigger is depressed.
 
NOTE: This tool has no provision for locking the tool on, and the switch should never
be locked on by any other means.
AUTOMATIC ELECTRIC BRAKE


SAWING
WARNING: To reduce the risk of serious personal injury,always hold the tool with both hands.



HINTS FOR OPTIMUM USE

avoided, cut on the side where splintering is acceptable.

plywood onto the top of the workpiece.
POCKET CUTTING (FIG. N)
WARNING: Never tie the blade guard in a raised
position. Never move the saw backwards when
pocket cutting. This may cause the unit to raise up
off the work surface which could cause injury.
A pocket cut is one that is made when the edge of the
material does not push the lower guard open, but the bottom
edge of the rotating blade cuts into the middle of the material.


shoe
on
material to be cut.
N
14
MAINTENANCE


IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
            

ACCESSORIES
Recommended accessories for use with your tool are available from your local dealer or
authorized service center. If you need assistance regarding accessories, please call:
1-800-544-6986.
WARNING: The use of any accessory not recommended for use with this tool
could be hazardous.
RBRC SEAL
TM


battery pack) at the end of its useful life have already been paid by . In


 and other battery users, has established programs

shoe
until blade teeth almost touch cutting line.


shown in figure N. Position your body and arm to allow you to resist kickback if it occurs.


its shoe rests flat on the material to be cut. Advance saw along the cutting line until cut is
completed as shown in figure N.

the material.

TROUBLESHOOTING
Problem Possible Cause Possible Solution
  
installation.
 

  

appears.
 
working outlet. Refer to

for more details.
 
too hot or too cold. pack to a surrounding air
temperature of above 40



  
 
To 
maximize the life of the allow to charge.
battery pack it is designed
to shutoff abruptly when
the charge is depleted.)
For assistance with your product, visit our website www.blackanddecker.com for the location
of the service center nearest you or call the

help line at 1-800-544-6986.
15

protect our environment and conserve natural resources by returning the tool to an authorized
 service center for recycling. You may also contact your local recycling center
for information on where to drop off the spent battery, or call 1-800-8-BATTERY.
NOTE: Batteries are integrated into the tool and should not be removed. To recycle,
return the tool to an authorized  service center.



accept any interference received, including interference that may cause undesired operation.
NOTE: 

provide reasonable protection against harmful interference in a residential installation.

installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.


to correct the interference by one or more of the following measures:



receiver is connected.




SERCIVE INFORMATION
All          
           
advice, repair, or genuine factory replacement parts, contact the 
location nearest you. To find your local service location, call 1-800-544-6986 or visit
www.blackanddecker.com
LIMITED TWO-YEAR HOME USE WARRANTY
    
material or workmanship. The defective product will be replaced or repaired at no charge
in either of two ways.





 owned


This warranty does not apply to accessories. This warranty gives you specific legal rights
and you may have other rights which vary from state to state or province to province.


FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or
are missing, call 1-800-544-6986 for a free replacement.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, check country specific warranty information contained
in the packaging, call the local company or see the website for warranty information.the
packaging, call the local company or see the website for warranty information.
Imported by

701 E. Joppa Rd.

16
LIGNES DIRECTRICES EN MATIÈRE DE SÉCURITÉ - DÉFINITIONS



DANGER : 
causera la mort ou des graves blessures.
AVERTISSEMENT : 

MISE EN GARDE : 

AVIS : 

MODE D’EMPLOI
SCIE CIRCULAIRE DE LI-ION DE 20 V
MAX.*, 140 MM (5 1/2 PO)
Merci d’avoir choisi BLACK+DECKER! Consulter le site Web
www.BlackandDecker.com/NewOwner pour enregistrer votre nouveau produit.
ÀLIRE AVANT DE RETOURNER CE PRODUIT POUR QUELQUE
RAISON QUE CE SOIT :
Si des questions ou des problèmes surgissent après l’achat d’un produit
BLACK+DECKER, consulter le site Web www.blackanddecker.com/instantanswers
pour obtenir des réponses instantanément 24 heures par jour. Si la réponse est
introuvable ou en l’absence d’accès à l’Internet, composer le 1 800 544-6986 de 8 h à
17 h HNE, du lundi au vendredi, pour parler avec un agent. Prière d’avoir le numéro de
catalogue sous la main lors de l’appel.
Pour l´achat d´un filtre de rechange composer le 1-888-678-7278
CONSERVER CE MODE D’EMPLOI POUR UN USAGE ULRIEUR.
*La tension initiale maximale du bloc-piles (mesurée sans charge de
travail) est de 20 volts. La tension nominale est de 18.
NUMERO DE CATALOGUE
BDCCS20
17
Avertissements de sécurité généraux pour les outils électriques
AVERTISSEMENT : Lire tous les avertissements de sécurité et toutes
les directives. 

Conserver tous les avertissements et toutes les directives pour un usage ultérieur.


1) Sécurité du lieu de travail
a) Tenir la zone de travail propre et bien éclairée. Les endroits sombres sont
souvent des causes d’accidents.
b) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, soit en
présence de liquides inflammables, de gaz ou de poussière. Les outils
électriques produisent des étincelles qui peuvent enflammer la poussière ou les vapeurs.
c) Éloigner les enfants et les curieux au moment d’utiliser un outil électrique.
Une distraction pourrait vous en faire perdre la maîtrise.
2) Sécurité en matière d’électricité
a) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais
modifier la fiche en aucune façon. Ne jamais utiliser de fiche d’adaptation avec
un outil électrique mis à la terre. Le risque de choc électrique sera réduit par
l’utilisation de fiches non modifiées correspondant à la prise.
b) Éviter tout contact physique avec des surfaces mises à la terre comme des
tuyaux, des radiateurs, des cuisinières et des réfrigérateurs. Le risque de choc
électrique est plus élevé si votre corps est mis à la terre.
c) Ne pas exposer les outils électriques à la pluie ou à d’autres conditions où il
pourrait être mouillé. La pénétration de l’eau dans un outil électrique augmente le
risque de choc électrique.
d) Ne pas utiliser abusivement le cordon d’alimentation. Ne jamais utiliser le
cordon pour transporter, tirer ou débrancher un outil électrique. Tenir le cordon
éloigné de la chaleur, de l’huile, des bords tranchants ou des pièces mobiles.
Les cordons endommagés ou emmêlés augmentent les risques de choc électrique.
e) Pour l’utilisation d’un outil électrique à l’extérieur, se servir d’une rallonge
convenant à une telle utilisation. L’utilisation d’une rallonge conçue pour
l’extérieur réduit les risques de choc électrique.
f) S’il est impossible d’éviter l’utilisation d’un outil électrique dans un endroit
humide, brancher l’outil dans une prise ou sur un circuit d’alimentation dotés
d’un disjoncteur de fuite à la terre (GFCI). L’utilisation de ce type de disjoncteur
réduit les risques de choc électrique.
3) Sécurité personnelle
a) Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un outil
électrique est utilisé. Ne pas utiliser d’outil électrique en cas de fatigue ou sous
l’influence de drogues, d’alcool ou de médicaments. Un simple moment d’inattention
en utilisant un outil électrique peut entraîner des blessures corporelles graves.
b) Utiliser des équipements de protection individuelle. Toujours porter une
protection oculaire. L’utilisation d’équipements de protection comme un masque
antipoussière, des chaussures antidérapantes, un casque de sécurité ou des protecteurs
auditifs lorsque la situation le requiert réduira les risques de blessures corporelles.
c) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se trouve
à la position d’arrêt avant de relier l’outil à une source d’alimentation et/ou
d’insérer un bloc-piles, de ramasser ou de transporter l’outil. Transporter un outil
électrique alors que le doigt repose sur l’interrupteur ou brancher un outil électrique
dont l’interrupteur est à la position de marche risque de provoquer un accident.
d) Retirer toute clé de réglage ou clé standard avant de démarrer l’outil. Une clé
standard ou une clé de réglage attachée à une partie pivotante peut causer des blessures.
e) Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Cela
permet de mieux maîtriser l’outil électrique dans les situations imprévues.
f) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de
bijoux. Garder les cheveux, les vêtements et les gants à l’écart des pièces
mobiles. Les vêtements amples, les bijoux ou les cheveux longs risquent de rester
coincés dans les pièces mobiles.
g) Si des composants sont fournis pour le raccordement de dispositifs de
dépoussiérage et de ramassage, s’assurer que ceux-ci sont bien raccordés
et utilisés. L’utilisation d’un dispositif de dépoussiérage peut réduire les dangers
18
engendrés par les poussières.
4) Utilisation et entretien d’un outil électrique
a) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à
l’application. L’outil électrique approprié effectuera un meilleur travail, de façon plus
sûre et à la vitesse pour laquelle il a été conçu.
b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout outil
électrique dont l’interrupteur est défectueux est dangereux et doit être réparé.
c) Débrancher la fiche du secteur ou le bloc-piles de l’outil électrique avant de faire
tout réglage ou changement d’accessoire, ou avant de ranger l’outil électrique. Ces
mesures préventives réduisent les risques de démarrage accidentel de l’outil électrique.
d) Ranger les outils électriques hors de la portée des enfants, et ne permettre à
aucune personne n’étant pas familière avec un outil électrique (ou son manuel
d’instruction) d’utiliser ce dernier. Les outils électriques deviennent dangereux
entre les mains d’utilisateurs inexpérimentés.
e) Entretenir les outils électriques. Vérifier les pièces mobiles pour s’assurer
qu’elles sont bien alignées et tournent librement, qu’elles sont en bon état et
ne sont affectées par aucun trouble susceptible de nuire au bon
fonctionnement de l’outil électrique. En cas de dommage, faire réparer l’outil
électrique avant toute nouvelle utilisation. Beaucoup d’accidents sont causés par
des outils électriques mal entretenus.
f) S’assurer que les outils de coupe sont aiguisés et propres. Les outils de coupe bien
entretenus et affûtés sont moins susceptibles de se coincer et sont plus faciles à contrôler.
g) Utiliser l’outil électrique, les accessoires, les forets, etc. conformément aux
présentes directives en tenant compte des conditions de travail et du travail à
effectuer. L’utilisation d’un outil électrique pour toute opération autre que celle pour
laquelle il a été conçu est dangereuse.
5) Réparation
a) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant
que des pièces de rechange identiques. Cela permettra de maintenir une
utilisation sécuritaire de l’outil électrique.
RÈGLES DE SÉCURITÉ SPÉCIFIQUES SUPPLÉMENTAIRES
CONSIGNES DE SÉCURITÉ POUR TOUTES LES SCIES
DANGER :
a. Gardez les mains à distance de la zone de coupe et de la lame. Gardez une de
vos mains sur la poignée auxiliaire ou sur le carter du moteur. Si vous tenez la

b. N’essayez pas de tenir le dessous de l’ouvrage.

c. Ajustez la profondeur de coupe à l’épaisseur de l’ouvrage. Moins d’une dent

d. Ne tenez jamais dans vos mains ou sur vos genoux un ouvrage qui est en
cours de coupe. Fixez votre ouvrage sur une plateforme stable. Il est important


e. Tenez l’outil électrique par ses surfaces de préhension isolantes quand vous
réalisez une opération au cours de laquelle l’outil de coupe pourrait entrer en
contact avec des câbles dissimulés ou avec son propre cordon électrique. Le


f. Pendant les coupes de refente, utilisez toujours un guide de refente ou un
guide à bord droit.

g. Utilisez toujours des lames dont l’alésage central est de la taille et de la forme
appropriées (soit en forme de diamant, soit en forme de rond).


h. Ne vous servez jamais de rondelles ou de boulons de lames qui sont endommagés ou
inappropriés.
scie dans le but d’assurer une performance optimale et un fonctionnement sans danger.
18
1919
CAUSES DES REBONDS ET MÉTHODES DE PRÉVENTION
POUVANT ÊTRE UTILISÉES PAR L’UTILISATEUR :
 

l’ouvrage et sa projection en direction de l’utilisateur.
 


 Si la lame se tord ou perd son alignement correct au cours de la coupe, les dents sur le




a. Maintenez fermement la scie avec vos deux mains et positionnez vos bras
de façon à résister aux forces de rebond. 

b. En cas de coincement de la lame ou d’interruption d’une coupe pour une raison
quelconque, relâchez la gâchette et tenez la scie immobile dans l’ouvrage
jusqu’à ce que la lame se soit immobilisée complètement. Ne tentez jamais de
retirer la scie de l’ouvrage ou de la tirer vers l’arrière pendant que la lame est en
mouvement, car un rebond risquerait de se produire. Évaluez la situation et prenez

c. Lorsque vous remettez une scie en marche quand l’ouvrage est présent, centrez
la lame de scie dans le trait de scie et vérifiez que les dents de la lame ne sont
pas engagées dans le matériau de l’ouvrage. Si la lame de scie se coince, elle peut

d. Soutenez les panneaux de grande taille de façon à minimiser le risque de
pincement et de rebond de la lame.


e. N’utilisez pas de lame émoussée ou endommagée.

coincement de la lame et un effet de rebond.
f. Les leviers de réglage de la profondeur et de l’angle de coupe de la lame
doivent être bien serrés et assujettis avant de réaliser une coupe. Une

coincement et un rebondissement de la lame.
g. Procédez avec une prudence supplémentaire quand vous réalisez une coupe
« en plongée » dans des murs déjà en place ou dans des pièces sans issue.

CONSIGNES DE SÉCURITÉ RELATIVES AU PROTÈGE-LAME INFÉRIEUR
a. Inspectez le protège-lame inférieur avant chaque utilisation pour vous assurer qu’il
se ferme correctement. Ne faites pas fonctionner la scie si le
protège-lame inférieur ne se déplace pas librement et ne se ferme pas
instantanément. 




b. Vérifiez le fonctionnement du ressort du protège-lame inférieur. Si le
protège-lame inférieur et le ressort ne fonctionnent pas correctement, ils
doivent être réparés avant l’emploi.

c. Le protège-lame inférieur doit être rétracté à la main uniquement à l’occasion
de coupes spéciales telles que les « coupes en plongée » ou les « coupes
composées ». Soulevez le protège-lame inférieur à l’aide la poignée rétractable
et relâchez-le dès que la lame pénètre dans le matériau de l’ouvrage. Pour toute

d. Vérifiez toujours que le protège-lame inférieur couvre la lame avant de placez
la scie sur un banc ou sur le sol. 



20
DIRECTIVES DE SÉCURITÉ SUPPLÉMENTAIRES
Utiliser des pinces ou tout autre moyen pratique de soutenir et de fixer solidement
la pièce sur une plate-forme stable. Tenir la pièce avec la main ou contre son corps

Il faut se tenir de l’un ou l’autre côté de la lame de la scie et non dans sans trajectoire.
 «
Causes de l’effet de rebond et prévention par l’opérateur » et « EFFET DE REBOND »).
 Éviter de couper des clous. Inspecter le bois et retirer tous les clous qui s’y
trouvent avant d’entamer la découpe.
Toujours s’assurer que rien ne nuit au mouvement du pare-main inférieur.
Le régime nominal (vitesse) des accessoires doit au minimum égaler la vitesse
recommandée sur l’étiquette d’avertissement de l’outil. Les meules et autres
accessoires allant plus vite que le régime nominal peuvent être projetés et
provoquer des blessures.


solidement avant d’utiliser l’outil.












Pour la sécurité de l’utilisateur, utiliser une rallonge de calibre adéquat (AWG ou
American Wire Gauge [calibrage américain normalisé des fils]). 







Calibre de fil minimum recommandé pour les rallonges
Longueur totale de la rallonge
25 pi 50 pi 75 pi 100 pi 125 pi 150 pi 175 pi
7,6 m 15,2 m 22,9 m 30,5 m 38,1 m 45,7 m 53,3 m
Calibre AWG
18 18 16 16 14 14 12
ATTENTION : La lame après l’éteindre. Des blessures graves peuvent en résulter.
AVERTISSEMENT : Toujours porter une protection auditive appropriée
conformément à la norme ANSI S12.6 (S3.19) lors de l’utilisation du produit. Dans
certaines conditions et selon la durée d’utilisation, le bruit émis par ce produit pourrait
contribuer à une perte auditive.
AVERTISSEMENT : Toujours utiliser une protection oculaire appropriée.
Tous les utilisateurs et les spectateurs doivent porter des lunettes de protection
conforme à la norme ANSI Z87.1.
AVERTISSEMENT : TOUJOURS porter des lunettes de sécurité. Les lunettes
de vue ne constituent PAS des lunettes de sécurité. Utiliser également un masque
facial ou anti-poussière si l’opération de découpe génère de la poussière. TOUJOURS
PORTER UN ÉQUIPEMENT DE PROTECTION HOMOLOGUÉ :
protection oculaire conforme à la norme ANSI Z87.1 (CAN/CSA Z94.3);
protection auditive ANSI S12.6 (S3.19);
protection des voies respiratoires conformes aux normes NIOSH/OSHA/MSHA.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Black & Decker BDCCS20B Manuel utilisateur

Catégorie
Scies circulaires
Taper
Manuel utilisateur