LanParty Blood-Iron P45 Elite Series Manuel utilisateur

935-DP45T1-600G

05800820E

System Board

User’s Manual

Copyright

This publication contains information that is protected by copyright. No part of it

may be reproduced in any form or by any means or used to make any transfor-

mation/adaptation without the prior written permission from the copyright hold-

ers.

This publication is provided for informational purposes only. The manufacturer

makes no representations or warranties with respect to the contents or use of

this manual and specifically disclaims any express or implied warranties of

merchantability or fitness for any particular purpose. The user will assume the

entire risk of the use or the results of the use of this document. Further, the

manufacturer reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or entity of such

revisions or changes.

Trademarks

Windows® 2000 and Windows® XP are registered trademarks of Microsoft

Corporation. Award is a registered trademark of Award Software, Inc. Other

trademarks and registered trademarks of products appearing in this manual are

the properties of their respective holders.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC rules. These limits are designed

to provide reasonable protection against harmful interference when the equip-

ment is operated in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not occur in a par-

ticular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsi-

ble for compliance could void the user's authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission

limits.

Table of Contents

About this Manual................................................................................

Warranty.................................................................................................

Static Electricity Precaution................................................................

Safety Measures.....................................................................................

About the Package...............................................................................

Before Using the System Board.........................................................

System Board Layout............................................................................

English.....................................................................................................

Français...................................................................................................

Deutsch...................................................................................................

Español....................................................................................................

General Debug LED POST and Troubleshooting ........................

4

5

6

7

8

32

59

85

111

Introduction

1

4

About this Manual

An electronic file of this manual is included in the CD. To view the

user’s manual in the CD, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click the

“TOOLS” icon then click “Manual” on the main menu.

For additional information on the system board, please download

the complete version of the manual from DFI’s website. Visit

www.dfi.com.

Warranty

1. Warranty does not cover damages or failures that arised from

misuse of the product, inability to use the product, unauthorized

replacement or alteration of components and product specifica-

tions.

2. The warranty is void if the product has been subjected to physi-

cal abuse, improper installation, modification, accidents or unau-

thorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may

not, under any circumstances, attempt to perform service, adjust-

ments or repairs on the product, whether in or out of warranty.

It must be returned to the purchase point, factory or authorized

service agency for all such work.

4. We will not be liable for any indirect, special, incidental or

consequencial damages to the product that has been modified

or altered.

1

Introduction

5

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board,

components or devices even before installing them in your system

unit. Static electrical discharge can damage computer components

without causing any signs of physical damage. You must take extra

care in handling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its

anti-static bag until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of

the components, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connec-

tors. Hold modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor, disk

drive and other components. Perform the upgrade instruction

procedures described at an ESD workstation only. If such a

station is not available, you can provide some ESD protection

by wearing an antistatic wrist strap and attaching it to a metal

part of the system chassis. If a wrist strap is unavailable, estab-

lish and maintain contact with the system chassis throughout

any procedures requiring ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

by

the manufacturer.

• Dispose of used batteries according to local ordinance.

Introduction

1

6

About the Package

The system board package contains the following items. If any of

these items are missing or damaged, please contact your dealer or

sales representative for assistance.

;The system board

;A user’s manual

;One IDE cable

;One FDD cable

;Two Serial ATA data cables

;One power cable with 2 Serial ATA power connectors

;One RAID floppy diskette

;One I/O shield

;One “Mainboard Utility” CD

The system board and accessories in the package may not come

similar to the information listed above. This may differ in accordance

to the sales region or models in which it was sold. For more infor-

mation about the standard package in your region, please contact

your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need

at least the following internal components.

•A CPU

•Memory module

•Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use

which will normally include at least a keyboard, a mouse and a video

display monitor.

1

Introduction

7

System Board Layout

Mouse

KB

Optical

S/PDIF-out

LAN

USB 7

USB 6

Line-in

Front R/L

Mic-in

Center/

Subwoofer

Side R/L

Rear R/L

1

Coaxial RCA

S/PDIF-out

USB 9

USB 8

USB 11

USB 10

CD-in

1

ITE

IT8718F

SATA 3

SATA 2

SATA 1

SATA 0

SATA 5

SATA 4

System fan

1

Front panel

1

Chassis fan

USB 4-5 USB 2-3 USB 0-1

FDD

1

COM

Battery

Front audio

1

IrDA

5V/12V

power

1

5V/12V

power

1

PCIE 1

PCIE 3

2412

ATX

power

113

JMicron

JMB368

1

CPU fan

DIMM 1

DIMM 2 DIMM 4

DIMM 3

12V power

1

JP17 JP18

1

JP19

1

SPI Flash

BIOS

ResetPower

1

Socket 775

1

PS/2 power

select (J 7)P

Marvell

88E8053

USB 6-11 power

select (J 5)P

1

NB Fan

IDE

USB 0-5 power

select (J )P6

1

1Intel

ICH10R

Intel

P45

Standby

Power LED

PCI 1

PCI 2

PCIE 2

PCIE 4

Realtek

ALC885

DRAM Power LED

Clear CMOS (JP8)

CPU FSB select

(JP17-JP19)

11 1

Clear

CMOS (JP2)

Secondary RTC

reset (JP12)

1

2

7

8

Download

BIOS (JP13)Flash

English

E

8

English

Chapter 1 - Introduction

Specifications

Processor

Chipset

System Memory

Expansion Slots

BIOS

Audio

LAN

IDE

Serial ATA with

RAID

• LGA 775 socket for:

- Intel® CoreTM2 Quad and Intel® CoreTM2 Duo

• Supports Intel Enhanced Memory 64 Technology (EMT64T)

• Supports Enhanced Intel SpeedStep Technology (EIST)

• Supports Intel Hyper-Threading Technology

• Supports 1333/1066/800MHz FSB

• Intel® chipset

- Northbridge:

Intel® P45 Express chipset

Intel® Fast Memory Access technology

- Southbridge: Intel® ICH10R

• Four 240-pin DDR2 DIMM sockets

• Supports DDR2 667/800 MHz

• Delivers up to 12.8Gb/s bandwidth

• Supports dual channel (128-bit wide) memory interface

• Supports up to 8GB system memory

• Supports unbuffered x8 and x16 DIMMs

• 2 PCI Express (Gen 2) x16 slots

- 2-way CrossFire: One slot operating at x16 (16-lane port)

or two slots each operating at x8 (8-lane ports) bandwidth

• 2 PCI Express x1 slots

• 2 PCI slots

• Award BIOS

• 8Mbit SPI flash BIOS

• CMOS Reloaded

• Realtek ALC885 High Definition audio CODEC

• 8-channel audio output

• DAC SNR/ADC SNR of 106dB/101dB

• Full-rate lossless content protection technology

• Optical S/PDIF-out and coaxial RCA S/PDIF-out interfaces

• Marvell 88E8053 PCIE Gigabit LAN controller

• Fully compliant to IEEE 802.3 (10BASE-T), 802.3u (100BASE-

TX) and 802.3ab (1000BASE-T) standards

• JMicron JMB368 PCI Express to PATA host controller

• Supports up to 2 UltraDMA 33/66/100Mbps IDE devices

• Intel Matrix Storage technology

• Supports up to 6 SATA devices

• SATA speed up to 3Gb/s

• RAID 0, RAID 1, RAID 0+1 and RAID 5

E

English

9

English

Rear Panel I/O

Internal I/O

Power Management

Hardware Monitor

PCB

• 1 mini-DIN-6 PS/2 mouse port

• 1 mini-DIN-6 PS/2 keyboard port

• 1 optical S/PDIF-out port

• 1 coaxial RCA S/PDIF-out port

• 6 USB 2.0/1.1 ports

• 1 RJ45 LAN port

• Center/subwoofer, rear R/L and side R/L jacks

• Line-in, line-out (front R/L) and mic-in jacks

• 3 connectors for 6 additional external USB 2.0 ports

• 1 connector for an external COM port

• 1 front audio connector

• 1 CD-in connector

• 1 IrDA connector

• 6 Serial ATA connectors

• 1 40-pin IDE connector

• 1 floppy connector

• 1 24-pin ATX power connector

• 1 8-pin 12V power connector

• 2 4-pin 5V/12V power connectors (FDD type)

• 1 front panel connector

• 4 fan connectors

• 1 download flash BIOS connector

• 1 diagnostic LED

• EZ touch switches (power switch and reset switch)

• ACPI and OS Directed Power Management

• ACPI STR (Suspend to RAM) function

• Wake-On-PS/2 Keyboard/Mouse

• Wake-On-USB Keyboard/Mouse

• Wake-On-LAN

• Wake-On-Ring

• RTC timer to power-on the system

• AC power failure recovery

• Monitors CPU/system/Northbridge temperature and overheat alarm

• Monitors Vcore/Vdimm/Vnb/VCC5/12V/V5sb/Vbat voltages

• Monitors the speed of the cooling fans

• CPU Overheat Protection function monitors CPU temperature

and fan during system boot-up - automatic shutdown upon sys-

tem overheat

• 4 layers, ATX form factor

• 24.5cm (9.64") x 30.5cm (12")

English

E

10

English

Chapter 2 - Hardware Installation

Jumper Settings

If you encounter the following,

a) CMOS data becomes corrupted.

b) You forgot the supervisor or user password.

c) The overclocked settings in the BIOS resulted to the system’s in-

stability or caused system boot up problems.

you can reconfigure the system with the default values stored in the

ROM BIOS.

JP8 is accessible from the rear panel of the system. This provides

convenience by allowing you to clear the CMOS without having to

remove the chassis cover.

Clear CMOS Data

Clearing CMOS Data using Jumpers

2-3 On:

Clear CMOS Data

1-2 On: Normal

(default)

JP2

JP8 X

2-3 On:

Clear CMOS Data

1-2 On: Normal

(default)

1

3

2

1

3

2

X

3

123

12

E

English

11

English

To load the default values stored in the ROM BIOS, please follow

the steps below.

1. Power-off the system then unplug the power cord.

2. Set JP2 or JP8 pins 2 and 3 to On. Wait for a few seconds and

set JP2 or JP8 back to its default setting, pins 1 and 2 On.

3. Now plug the power cord then power-on the system.

English

E

12

English

PS/2 Power Select

Selecting 5VSB will allow you to use the PS/2 keyboard or PS/2

mouse to wake up the system.

X

JP7

2-3 On:

5VSB

1-2 On: 5V

(default)

USB Power Select

X

USB 6-11

(JP5)

X

USB 0-5

(JP6)

2-3 On: 5VSB1-2 On: 5V

(default)

2-3 On: 5VSB1-2 On: 5V

(default)

Selecting 5VSB will allow you to use the USB keyboard or USB

mouse to wake up the system.

Important:

The 5VSB power source of your power supply must support ≥1.5A (2 devices)

or ≥2A (3 or more devices).

Important:

The 5VSB power source of your

power supply must support

≥720mA.

312312

312 312

31

231

2

E

English

13

English

By default, the three jumpers are all set to pins 1 and 2 On. This

setting will allow the system to automatically run according to the

CPU’s FSB. If you want to change the settings, please refer to the

table below.

JP17

JP18

JP19

By CPU

1-2 On

FSB 800

2-3 On

3-4 On

2-3 On

FSB 1066

2-3 On

FSB 1333

2-3 On

3-4 On

CPU FSB Select

X

JP17

423

JP18

JP19

1

English

E

14

English

Rear Panel I/O Ports

Secondary RTC Reset

When the RTC battery is removed, this jumper resets the

manageability register bits in the RTC.

Note:

1. The SRTCRST# input must always be high when all other

RTC power planes are on.

2. In the case where the RTC battery is dead or missing on

the platform, the SRTCRST# pin must rise before the

RSMRST# pin.

PS/2 K/B

Optical

S/PDIF-out

USB 10-11

USB 6-7

Coaxial

S/PDIF-out

Mic-in

Side R/L

Center/

Subwoofer Rear R/L

Line-in

Front R/L

LAN

PS/2

Mouse

USB 8-9

Clear

CMOS

jumper

2-3 On:

RTC reset

1-2 On: Normal

(default)

X

JP12 132132

E

English

15

English

PS/2 Mouse and PS/2 Keyboard Ports

These ports are used to connect a PS/2 mouse and a PS/2 key-

board.

Optical S/PDIF

The optical S/PDIF jack is used to connect an external audio output

device using an optical S/PDIF cable.

Coaxial RCA S/PDIF

The coaxial RCA S/PDIF jack is used to connect an external audio

output device using a coaxial S/PDIF cable.

Important:

DO NOT use optical S/PDIF and Coaxial RCA S/PDIF at the

same time.

PS/2 Ports and S/PDIF Ports

W

PS/2 Mouse

PS/2 KB

Optical

S/PDIF

Coaxial RCA

S/PDIF

W

English

E

16

English

1

VCC

-Data

+Data

GND

Key

VCC

-Data

+Data

GND

N. C.

210

9

W

USB 4-5

W

USB 0-1

USB 9

W

LAN

USB 8

USB 11

USB 10

USB 7

USB 6

USB Ports and LAN Port

USB Ports

The USB ports are used to connect USB 2.0/1.1 devices. The 10-pin

connectors allow you to connect 6 additional USB 2.0/1.1 ports.

Your USB ports may come mounted on a card-edge bracket. Install

the card-edge bracket to an available slot at the rear of the system

chassis then connect the USB port cables to these connectors.

LAN Port

The LAN port allows the system board to connect to a local area

network by means of a network hub.

USB 2-3

E

English

17

English

Rear Panel Audio

Center/Subwoofer Jack (Orange)

This jack is used to connect to the center and subwoofer speak-

ers of the audio system.

Rear Right/Left Jack (Black)

This jack is used to connect to the rear right and rear left speak-

ers of the audio system.

Side Right/Left Jack (Gray)

This jack is used to connect to the side left and side right speak-

ers of the audio system.

Line-in (Light Blue)

This jack is used to connect any audio devices such as Hi-fi set,

CD player, tape player, AM/FM radio tuner, synthesizer, etc.

Line-out - Front Right/Left Jack (Lime)

This jack is used to connect to the front right and front left

speakers of the audio system.

Audio and CD-In

W

Rear audio

Front audio

Front R/L

Line-in

Mic-in

Rear R/L

Center/

Subwoofer

Side R/L

1

210

Mic-L

Mic-R

Line-out-R

Front-sense

Line-out-L

GND

Presense-signal

Mic-jack-sense

Key

Line-out-jack-sense

94

1

Left audio channel

Right audio channel

Ground

W

CD-in

English

E

18

English

Serial ATA Connectors

The Serial ATA (SATA) connectors are used to connect Serial ATA

drives. Connect one end of the Serial ATA cable to a Serial ATA

connector and the other end to your Serial ATA device.

Configuring RAID

Refer to the RAID chapter in this manual for more information

about creating RAID on Serial ATA drives.

SATA 2-3

SATA 0-1

SATA 4-5

Mic-in Jack (Pink)

This jack is used to connect an external microphone.

Front Audio

The front audio connector is used to connect to the line-out and

mic-in jacks that are at the front panel of your system.

CD-in

The CD-in connector is used to receive audio from a CD-ROM

drive, TV tuner or MPEG card.

Internal I/O Connectors

E

English

19

English

X

40 39

21

FDD Connector and IDE Connector

FDD Connector

The floppy disk drive connector is used to connect a floppy drive.

Insert one end of the floppy cable into this connector and the other

end-most connector to the floppy drive. The colored edge of the

cable should align with pin 1 of this connector.

IDE Connector

The IDE disk drive connector is used to connect 2 IDE disk drives.

An IDE cable have 3 connectors on them, one that plugs into this

connector and the other 2 connects to IDE devices. The connector

at the end of the cable is for the Master drive and the connector in

the middle of the cable is for the Slave drive. The colored edge of

the cable should align with pin 1 of this connector.

Note:

When using two IDE drives, one must be set as the master

and the other as the slave. Follow the instructions provided by

the drive manufacturer for setting the jumpers and/or switches

on the drives.

X

IDE

FDD

34

33 1

2

English

E

20

English

IrDA and Serial (COM) Connectors

IrDA Connector

This connector is used to connect an IrDA module.

Note:

The sequence of the pin functions on some IrDA cable may be

reversed from the pin function defined on the system board.

Make sure to connect the cable connector to the IrDA

connector according to their pin functions.

You may need to install the proper drivers in your operating system

to use the IrDA function. Refer to your operating system’s manual or

documentation for more information.

Serial (COM) Connector

The serial (COM) connector is used to connect modems, serial print-

ers, remote display terminals, or other serial devices. Your COM port

may come mounted on a card-edge bracket. Install the card-edge

bracket to an available slot at the rear of the system chassis then

connect the serial port cable to this connector. The colored edge of

the cable should align with pin 1 of this connector.

W

19

2

CD

TD

RD

DTR

GND

RTS

DSR

CTS

RI

COM

15

VCC

N. C.

IRRX

Ground

IRTX

IrDA

X

La page charge ...

LanParty Blood-Iron P45 Elite Series Manuel utilisateur

LanParty Blood-Iron P45 Elite Series Manuel utilisateur

dans d''autres langues

Autres documents