Honeywell CFS8DLLMD500 Manuel utilisateur

Marque: Honeywell

Modèle: CFS8DLLMD500

Taper: Manuel utilisateur

Ce manuel convient également à

Lyric RF6PIR

This wireless passive infrared motion sensor is intended for use with Honeywell controls that support

SiX™ series devices.

Mounting Location

•The optimal range is

obtained at a mounting

height of 7’ 6” (2.3 m).

•Allow a clear line-of-sight

to all areas to protect.

•Do not directly face

windows.

•Avoid close proximity to

moving machinery,

fluorescent lights, and

heating/cooling sources.

•For use in applications

with pets up to 80

pounds (36 kilograms).

Mounting Options

The RF6PIR can be

mounted on the wall or in

corners:

•

[A]

= Wall mounting

holes.

•

[B]

= Corner mounting

holes.

•The rear tamper plate

MUST be mounted to a

stud, solid wood, or with

a robust wall anchor.

•UL requirements: TBD

Note

: before mounting the

RF6PIR permanently,

conduct Go/No Go tests

(see control’s instructions)

to verify adequate signal

strength and adjust the

device location and

orientation as necessary.

PRELIMINARY DRAFT IIs – 01/12/15

Enroll the RF6PIR

The RF6PIR can be enrolled and

programmed before or after installation.

• Press down on the top latch and separate

the front and back covers.

• Set the Lyric Smart Controller in

Programming Mode.

• Remove the RF6PIR battery tab to

activate and begin the enrollment process.

• The green LED beneath the battery flashes

during enrollment (about 8 seconds) and

the control beeps (TBD).

• The device sends the device MAC ID

address and Services information to the

control. The control registers the device

and displays the transmitter data on

screen.

• Enrollment is confirmed when the RF6PIR

LED is ON for 3 seconds [and the control

beeps TBD].

• If the sensor is not successfully enrolled

during the enrollment period, the LED

turns off and the device powers down.

Activate a tamper to restart the enrollment

process.

Note

: Once enrolled in a system, the sensor

cannot be used with another control panel until

it is removed from the current control panel. See

the Control’s instructions for details on

removing devices.

Programming RF6PIR Services

Fault device features to “Learn” device

“Services” in the control:

- Cover and Wall tamper switches

- Selectable Pet Immunity –

Off or up to 80 lbs (36 kg)

- Temperature sensor; accuracy ±3°F

Consult the Lyric Smart Controller’s

instructions for programming the device in

the system.

Walk Test the RF6PIR

After power up and enrollment, activate the

Test Mode with the control (see control’s

instructions) or use the Flashlight Feature.

Test period.

Note

: the system must be in

disarmed

mode for

the 10 minute Test mode to begin.

Walk through the detection area and observe

the LED.

Test Mode is active for 10 minutes, then

automatically exits test mode, disables the

LED and enters normal operation mode.

To restart the 10 minute Test Mode, use the

flashlight feature (see the following section).

Flashlight Feature

The flashlight feature is initially only available for the

first 24 hours after the first power up, or until the

system is first armed.

This feature is no longer

available after the first system arming

Each time the flashlight features is used, and the system

is disarmed, the walk test timer restarts for 10 minutes.

1. Use a flashlight with a bright light beam, and stand

within 4’ (1.2 m) of the sensor.

2. Swing the light beam past the sensor Lens 3-5 times,

holding the beam on the window for 0.5 second each

pass.

Detection Patterns

Battery Replacement

• Remove the front cover.

• Replace the battery.

Recommended replacement batteries:

Panasonic CR123A

Honeywell 466

Duracell DL123 or DL123A

• Replace the front cover.

BATTERY CAUTION:

Risk of fire, explosion and burns.

Do not recharge, disassemble, heat above 212° F (100°

C) or incinerate. Dispose of used batteries promptly.

Keep away from children.

Specifications

Power - Battery:

One 3V, Lithium; Panasonic CR123A, Duracell DL 123 or DL

123A, Honywell 466

Battery Life, years (typical):

4 years

Range:

40’ x 56’ / 12 m x 17 m

Wall Mounting Height:

7’ – 9’ (2.1 m – 2.7 m); Optimal 7’6” (2.3 m)

Tampers:

Cover and Wall; (reported separately to the panel)

Operating Temperature:

32° to 122° F / 0° to 50° C

Relative Humidity:

5 to 95%; non-condensing

Temperature Compensation:

Advanced Dual Slope

Dimensions:

4.13” H x 2.38” W x 1.61” D / 105 mm H x 60.4 mm W x 41 mm D

Weight:

x oz / xx g (net weight)

Approval Listings

FCC / IC

SIA-PIR-01

ETL

UL 639

ULC S306-03

RoHS

The product must be tested

at least

once each year

Zones

Lower

Intermediate

Long

Note: the flashlight feature only initiates

or restarts the Test Mode and does not

change any other sensor settings.

FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized

changes or modifications could void the user's authority to operate the equipment.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes:

(1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une

reception indésirable.

RF Exposure

Warning – The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must

not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.

Mise en Garde