Honeywell DT8035 Dual Tec Quick Installation Manual

Marque: Honeywell

Modèle: DT8035 Dual Tec

Catégorie: Détecteurs de mouvement

Taper: Quick Installation Manual

DT8035 DUAL TEC

Motion Sensor - Quick Installation Guide

Détecteur de mouvement DT8035 DUAL TEC

– Guide d'installation rapide

Sensor de Movimiento DUAL TEC

DT8035 – Guía Rápida de Instalación

Sensor de Movimento DUAL TEC

DT8035 – Guia rápido de instalação

6' 9" - 8' 9"

(2.1 - 2.7 m)

7' 6"

(2.3 m)

≤ 100 lbs / 45 kg

Optimal

Optimo

Ótimo

#6 x 1"

(3.5 mm x 25 mm)

#6 x 1"

(3.5 mm x 25 mm)

SENSITIVITY

MAX

MIN

LOOKDOWN

OFF

MIN MAX

LED

OFF

DT8035

*Enabled

*Activé

*Habilitado

Disabled

Désactivé

Deshabilitado

OFF

Pet Immunity

Insensibilité aux animaux

Tolerancia a mascotas

Pet-Imunidade

Microwave Range Adjustment

Réglage de la portée des micro-ondes

Ajuste del rango de detección Microondas

Ajuste de Alcance Microondas

* Factory default / Valeurs par défaut du fabricant /

Defecto de fábrica / Padrão de fábrica

PI LED

ON OFF

(Sensibilité micro-ondes)

(Sensibilidad de Microonda)

(Sensibilidade da Microonda)

- 2 -

T C V-V+

T NC

Ground +12V

Zone

COM

Zone

COM

Tamper

30 mA

25 VDC

Power

17 mA

9-15 VDC

(UL: 9.5-15 VDC)

Alarm

30 mA

25 VDC

6 4 2 15 3

22-20 AWG

(0.31-0.52mm2)

T C V-V+

T NC

6 4 2 15 3

Panel / Panneau / Panel / Controle

Sensor / Détecteur / Sensor / Sensor

30 sec

SENSITIVITY

MAX

MIN

PI LED

1/2 sec.

hold 4x

< 4’ (1.2m)

Walk Test Reset

1. Apply power to the sensor. Initialization is complete when the LED stops

flashing slowly (about 30 seconds).

2. Turn the microwave sensitivity counterclockwise to reduce the microwave

range (minimum = 16.4’ / 5m) and close the sensor.

3. Walk through the detection area and observe the LED.

4. Adjust the microwave range as necessary to meet installation requirements.

Walk test mode is active for 10 minutes, then automatically exits test mode, disables the LED and enters normal

operation mode. For an additional 10 minute walk test, enable walk test mode again with the flashlight feature (see Walk

Test Reset above).

Note: During power up and walk test modes the LED is active regardless of the LED Enable/Disable DIP switch setting.

PLAN VIEW

ALL ZONES

A B C D

7.5ft

(2.3m)

0ft

(0m)

7ft

(2m) 13ft

(4m) 20ft

(6m) 27ft

(8m) 33ft

(10m) 40ft

(12m)

13ft

(4m)

0ft

(0m) 7ft

(2m) 13ft

(4m) 20ft

(6m) 27ft

(8m) 33ft

(10m) 40ft

(12m)

7ft

(2m)

0ft

(0m)

7ft

(2m)

13ft

(4m)

20ft

(6m)

20ft

(6m)

27ft

(8m)

33ft

(10m)

27ft

(8m)

33ft

(10m)

Top View

Vue de dessus

Vista Desde Arriba

Vista Superior

Side View

Vue de coté

Vista Lateral

LED Power Up

Walk Test Normal Fault

Red Slow

Blink

Alarm

Fast

Blink

Yellow OFF ON

Microwave

Microwave OFF

Green OFF ON

PIR

PIR OFF

Zones / Zones / Zonas / Zonas

Look-down / Basses / Vista Zona 0 /

Vigilância inferior

Lower / Courtes / Cercana/ Mais baixas

Intermediate / Intermédiaires / Intermedia /

Intermédias

Long / Longues / Largo Alcance / Longo

alcance

- 3 -

SPECIFICATIONS:

Operating Temperature: 14° to 131° F / -10° to 55° C

Relative Humidity: 5 to 93% (UL tested at 93%); non-condensing

TROUBLESHOOTING:

TROUBLE*

NORMAL

Self

Test Failure

Alarm Relay

Closed Open

Red LED

Off Flashing

*TROUBLE CONDITIONS:

Self-Test Failure conditions:

• Microwave supervision failure: The sensor is operating in PIR mode only.

• PIR self-test failure: The sensor is disabled.

• Temperature compensation failure: The temperature compensation is disabled.

Depending on the Trouble condition, take the following corrective actions:

• Verify the power supply is sufficient (at least 9V at the sensor).

• Cycle power to the sensor.

• Walk test the sensor.

If the Trouble condition does not clear, replace the sensor.

APPROVAL LISTINGS:

• FCC part 15, Class B verified

• IC ICES-003, Class B verified

• UL 639

• ULC S306-03

• SIA-PIR-01 Passive Infrared detector standard features for false alarm immunity.

Product must be tested at least once each year / Le fonctionnement du produit doit être vérifié au moins une fois par année /

El producto debe ser probado al menos una vez al año / O produto deve ser testado pelo menos uma vez por ano

All wiring must be in accordance with: the National Electrical Code (ANSI/NFPA70); the Canadian Electrical Code, Part I (where applicable); UL681,

Standard for Installation and Classification of Burglar and Holdup Alarm Systems; ULC-S302, Standard for Installation and Classification of Burglar

Alarm Systems for Financial and Commercial Premises, Safes and Vaults; ULC-S310, Standard for Installation and Classification of Residential Burglar

Alarm Systems; local codes and the authorities having jurisdiction.

The products are intended to be powered by a power-limited output of a UL/CUL Listed Burglar Alarm control unit, or via a Listed UL603/ULC-S318

power-limited power supply that provides 4 hours of standby power.

The sensor must be mounted indoors, within the protected premises, and on a wooden stud, solid wood or with a robust wall anchor.

UL Notes: All interconnecting devices must be UL listed. The pet immunity feature has not been evaluated by UL.

FEDERAL COMMUNICATIONS COMMISSION STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.

Unauthorized changes or modifications could void the user's authority to operate the equipment.

CLASS B DIGITAL DEVICE STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your

information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the

manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for

a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection

against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient the receiving antenna until interference is reduced or eliminated.

• Move the radio or television receiver away from the receiver/control.

• Move the antenna leads away from any wire runs to the receiver/control.

• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.

• Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA CLASS B STATEMENT

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause

undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux

conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris

les interférences causant une réception indésirable.