Axis 211W Manuel utilisateur

Marque: Axis

Modèle: 211W

Catégorie: Des caméras de sécurité

Taper: Manuel utilisateur

ENGLISH FRANCAIS DEUTSCH ESPAÑOL

ITALIANO

AXIS 211W

Network Camera

Installation Guide

AXIS 211W Installation Guide Page 3

ENGLISH

AXIS 211W

Installation Guide

This installation guide provides instructions for installing the AXIS 211W Network Camera

on your network. For all other aspects of using the product, please see the User’s Manual,

available on the CD included in this package, or from www.axis.com/techsup

Installation steps

1. Check the package contents against the list below.

2. Hardware overview. See page 4.

3. Install the hardware. See page 5.

4. Set an IP address. See page 6.

5. Set the password. See page 9.

6. Configure the wireless connection. See page 10.

7. Adjust the focus. See page 14.

Package contents

Item Models/variants/notes

Network camera AXIS 211W with antenna

PS-K indoor power supply

(country specific)

Europe

Australia

USA/Japan

Argentina

Korea

Terminal block connector 4-pin connector block for connecting external devices to the I/O terminal

connector

Camera stand Supplied with mounting screws

CD AXIS Network Video Product CD, including product documentation, installa-

tion tools and other software

Printed Materials AXIS 211W Installation Guide (this document)

Axis Warranty Document

Important!

This product must be used in

compliance with local laws

and regulations.

Page 4 AXIS 211W Installation Guide

Hardware overview

Dimensions

HxWxD = 38 x 88 x180mm (1.5" x 3.5" x 7")

Weight =260g (0.57 lb) (without antenna)

Network indicator LED

Network

connector

Power indicator LED

Status indicator LED and

Internal microphone

Antenna

Rear panel

Underside

Serial number

Control button

Tele/wide puller

DC-Iris

control cable

I/O terminal

connector

Power connector

Wireless indicator LED

Antenna

connector

Audio out

Audio in

Focus puller

AXIS 211W Installation Guide Page 5

ENGLISH

Install the hardware

Connect the cables and antenna

1. For indoor use, attach the antenna by screwing it into place. For outdoor use see the out-

door housing instructions.

2. Connect the camera to the network using a shielded network cable. This connection is

temporary and allows the camera’s settings to be configured via the wired network

before connecting to the wireless network.

3. Optionally connect external input/output devices, e.g. alarm devices. See page 16 for

information on the terminal connector pins.

4. Optionally connect an active speaker and/or external microphone.

5. Connect power, using one of the methods listed below:

• The supplied power connector.

• PoE (Power over Ethernet). If available, this is automatically detected when the

network cable is connected (see above).

• Connect power via the terminal connector. See page 16 for information on the

terminal connector pins.

6. Check that the indicator LEDs indicate the correct conditions. See the table on page 17

for further details. Note that some LEDs can be disabled and may be unlit.

!IMPORTANT! - The AXIS 211W is designed for indoor and outdoor use. To use

the camera outdoors, it must be installed in an approved outdoor housing.

Please see www.axis.com for more information on outdoor housings.

Page 6 AXIS 211W Installation Guide

Assign an IP address

Most networks today have a DHCP server that automatically assigns IP addresses to

connected devices. If your network does not have a DHCP server the AXIS 211W will use

192.168.0.90 as the default IP address.

If you would like to assign a static IP address, the recommended method in Windows is

either AXIS IP Utility or AXIS Camera Management. Depending on the number of cameras

you wish to install, use the method that best suits your purpose.

Both of these free applications are available on the Axis Network Video Product CD supplied

with this product, or they can be downloaded from www.axis.com/techsup

Notes:

• If assigning the IP address fails, check that there is no firewall blocking the operation.

• For other methods of assigning or discovering the IP address of the AXIS 211W, e.g. in other

operating systems, see page 15.

Method Recommended for Operating system

AXIS IP Utility See page 7 Single camera

Small installations

Windows

AXIS Camera Management

See page 8

Multiple cameras

Large installations

Installation on a different subnet

Windows 2000

Windows XP Pro

Windows 2003 Server

AXIS 211W Installation Guide Page 7

ENGLISH

AXIS IP Utility - single camera/small installation

AXIS IP Utility automatically discovers and displays Axis devices on your network. The

application can also be used to manually assign a static IP address.

Note that the computer running AXIS IP Utility must be on the same network segment

(physical subnet) as the AXIS 211W.

Automatic discovery

1. Check that the AXIS 211W is connected to the network and that power has been applied.

2. Start AXIS IP Utility.

3. When the camera appears in the window, double-click it to open its home page.

4. See page 9 for instructions on how to assign the password.

Assign the IP address manually (optional)

1. Acquire an unused IP address on the same network segment as your computer.

2. Select the AXIS 211W in the list.

3. Click the button Assign new IP address to the selected device and enter the IP

address.

4. Click the Assign button and follow the instructions.

5. Click the Home Page button to access the camera’s web pages.

6. See page 9 for instructions on how to set the password.

Page 8 AXIS 211W Installation Guide

AXIS Camera Management - multiple cameras/large installations

AXIS Camera Management can automatically discover multiple Axis devices, show

connection status, manage firmware upgrades and set IP addresses.

Automatic discovery

1. Check that the camera is connected to the network and that power has been applied.

2. Start AXIS Camera Management. When the AXIS 211W appears in the window, double-

click it to open the camera’s home page.

3. See page 9 for instructions on how to set the password.

Assign an IP address in a single device

1. Select AXIS 211W in AXIS Camera Management and

click the Assign IP button.

2. Select Assign the following IP address and enter the IP

address, the subnet mask and default router the device

will use.

3. Click the OK button.

Assign IP addresses in multiple devices

AXIS Camera Management speeds up the process of

assigning IP addresses to multiple devices, by suggesting IP

addresses from a specified range.

1. Select the devices you wish to configure (different mod-

els can be selected) and click the Assign IP button.

2. Select Assign the following IP address range and enter

the range of IP addresses, the subnet mask and default

router the devices will use.

3. Click the OK button.

AXIS 211W Installation Guide Page 9

ENGLISH

Set the password

When accessing the AXIS 211W for the first

time, the ‘Configure Root Password’ dialog

will be displayed.

1. Enter a password and then re-enter it, to

confirm the spelling. Click OK.

2. Enter the user name root in the dialog as

requested.

Note: The default administrator user name root cannot be deleted.

3. Enter the password as set above, and click OK. If the password is lost, the AXIS 211W

must be reset to the factory default settings. See page 18.

4. If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the

video stream in Internet Explorer. You will need administrator rights on the computer to

do this.

The Live View page of the AXIS 211W is displayed, with links to the Setup tools, which

allow you to customize the camera.

Setup - Provides all the tools for configuring

the camera to requirements.

Help - Displays

online help on all

aspects of using

the camera.

Page 10 AXIS 211W Installation Guide

Configure the wireless connection using a network cable

Once the AXIS 211W has been connected to your network, the wireless settings can be

configured. The fastest, most secure method to configure AXIS 211W is using a wired

connection, since it disables the wireless connection and ensures greater secrecy while

entering settings. The AXIS 211W automatically searches for available network connections,

and allows only one of these to be active at a time. Configuring the AXIS 211W using an

unsecured wireless connection is not recommended, since passphrases and keys saved will

be sent in plain text.

Open the wireless settings from Setup > Basic Configuration > Wireless.

Note: For even greater security use HTTPS. Go to Setup > System Options >

Security > HTTPS and refer to the camera’s online help.

Status of Wireless Networks

This list is the result of a network scan. Access points with a disabled SSID Broadcast will

not appear unless the camera is linked to it. The network the AXIS 211W is currently linked

to is shown in blue. A network using unsupported security is shown in grey. The following

information is provided:

•SSID - The name of a wireless network (or ad-hoc device). If the same name occurs

several times this means that several access points for that network were found. The

AXIS 211W cannot be configured to be linked to only one particular access point.

•Mode - An Access Point (Master) or Ad-Hoc device.

• Security - Shows which type of security the network uses. See below for the

supported security types.

•Channel - Shows the wireless channel currently in use.

•Signal strength - Shows the signal strength.

•Bit rate - The current bit rate in Mbit/s. This is only shown for the access point

currently in use.

AXIS 211W Installation Guide Page 11

ENGLISH

Wireless Settings

To establish communication, the wireless settings must be the same as in the access point or

ad-hoc device. You can select a network by clicking on an access point or ad-hoc device

under Status of Wireless Networks, which automatically fills in many of the required fields

under Wireless Settings. Keys, passphrases and certificates that are used for security must be

entered manually. Contact your Network Administrator for the requirement for the desired

access point or ad-hoc device.

SSID - The name of the wireless network you are configuring the camera for. Leave this field

blank if you would like the AXIS 211W to attempt to access the nearest unsecured network.

Note: SSID (Service Set Identifier) is sometimes written as ESSID (Extended Service Set

Identifier).

Mode - Select Master to access the network via an access point or Ad-hoc if you would like

to access another wireless device, e.g. a laptop with a wireless connection.

Security

AXIS 211W supports three security methods:

• WPA-/WPA2-PSK

• WPA-/WPA2-Enterprise

•WEP

Depending on the type of security chosen, the proper settings become active.

WPA-/WPA2-PSK

WPA settings - Enter the required Pre-shared Key for the access point, which can be a

hexidecimal number or a passphrase

WPA-/WPA2-Enterprise

WPA- Enterprise type - Choose the type of client/server authentication being used by

the access point; EAP-TLS or EAP-PEAP/MSCHAPv2.

Page 12 AXIS 211W Installation Guide

EAP-TLS

•Identity - Enter the user iden-

tity to present to the network

•Private key password - Enter

the password for your user

identity

•EAPOL version - Select the

version used (1 or 2) in your

access point

•Certificates - Upload a CA

certificate to present to the access point for authentication

EAP-PEAP/MSCHAPv2

•Identity - Enter the user

identity to present to the net-

work

•Password - Enter the pass-

word to present to the net-

work

•Version - Select the PEAP

version used at the access

point

•Label - Select the label used

by the access point.

•EAPOL version - Select version (1 or 2) depending on the version used at the

access point

•Certificates - Upload a CA

certificate to present to the access point for authentication

WEP

Authentication - Select Open or

Shared Key System Authentication,

depending on the method used by

your access point. Not all access

points have this option, in which

case they probably use Open Sys-

tem, which is sometimes known as

SSID Authentication.

Key length - This sets the length of

the key used for the wireless encryp-

tion, 64 or 128 bit. The encryption

key length can sometimes be shown

as 40/64 and 104/128.

AXIS 211W Installation Guide Page 13

ENGLISH

Key type - The key types available depend on the access point being used. The follow-

ing options are available:

•Manual - Allows you to manually enter the hex key.

•ASCII - In this method the string must be exactly 5 characters for 64-bit WEP

and 13 characters for 128-bit WEP.

•Passphrase - In 64-bit WEP, the Passphrase generates 4 different keys. For 128-

bit WEP, only 1 key is generated, which is then replicated for all 4 keys. Key gen-

eration is not standardized and can differ from brand to brand. Check that the

generated keys are identical to those in your access point - if not, they must be

entered manually.

•WEP - Active transmit key - When using WEP encryption, this selects which of

the 4 keys the AXIS 211W uses when transmitting.

Complete the wireless installation using a network cable

1. Check that the wireless settings in the camera correspond to the settings in the access

point.

2. Disconnect the network cable from the camera.

3. Refresh the web page after 20-30 seconds to confirm the wireless connection. If the

camera cannot be accessed, run AXIS IP Utility to discover the camera again.

Note: Wireless settings should always (during installation and at all other times) be

configured or changed in the camera first and in the wireless access point sec-

ondly. This ensures that the camera is always accessible when making changes.

Page 14 AXIS 211W Installation Guide

Adjust the image and focus

To focus the AXIS 211W, follow the instructions below.

1. From the Basic Configuration page in the

setup tools, open the Focus adjustment

page.

2. Set the DC-Iris to Disabled and click Save.

3. Unscrew the zoom puller on the lens by

turning it anti-clockwise. Adjust the zoom

setting as required. Re-tighten the zoom

puller.

4. Unscrew the focus puller on the lens.

Adjust the focus as required. Re-tighten

the focus puller.

5. From the Focus adjustment page, set the

DC-Iris to Enabled and click Save.

Note: The DC-Iris should always be disabled

while focusing the camera. This opens

the iris to its maximum, which gives the smallest depth of field and thus the best

conditions for correct focusing. When the focus is set with this method it will

then be maintained in any light conditions.

Accessing the AXIS 211W from the Internet

Once installed, your AXIS 211W is accessible on your local network (LAN). To access the

camera from the Internet, network routers must be configured to allow incoming traffic,

which is usually done on a specific port. Please refer to the documentation for your router

for further instructions. For more information on this and other topics, visit the Axis Support

Web at www.axis.com/techsup

Zoom puller

(Tele/wide)

Focus puller

AXIS 211W Installation Guide Page 15

ENGLISH

Other methods of setting the IP address

The table below shows the other methods available for setting or discovering the IP address.

All methods are enabled by default, and all can be disabled.

Set the IP address with ARP/Ping

1. Acquire an IP address on the same network segment your computer is connected to.

2. Locate the serial number (S/N) on the AXIS 211W label.

3. Open a command prompt on your computer and enter the following commands:

4. Check that the network cable is connected to the camera and then start/restart the

camera, by disconnecting and reconnecting power.

5. Close the command prompt when you see ‘Reply from 192.168.0.125: ...’ or similar.

6. In your browser, type in http://<IP address> in the Location/Address field and press Enter

on your keyboard.

Notes:

• To open a command prompt in Windows: from the Start menu, select Run... and type cmd. Click OK.

• To use the ARP command on a Mac OS X, use the Terminal utility in Application > Utilities.

Use in operating

system

Notes

UPnP™

Windows

(ME or XP)

When enabled on your computer, the camera is automatically

detected and added to “My Network Places.”

Bonjour MAC OSX

(10.4 or later)

Applicable to browsers with support for Bonjour. Navigate to the

Bonjour bookmark in your browser (e.g. Safari) and click on the

link to access the camera’s web pages.

AXIS Dynamic DNS

Service

All A free service from Axis that allows you to quickly and simply

install your camera. Requires an Internet connection with no

HTTP proxy. See www.axiscam.net for more information.

ARP/Ping All See below. The command must be issued within 2 minutes of

connecting power to the camera.

View DHCP server

admin pages

All To view the admin pages for the network DHCP server, see the

server’s own documentation.

Windows syntax Windows example

arp -s <IP Address> <Serial Number>

ping -l 408 -t <IP Address> arp -s 192.168.0.125 00-40-8c-18-10-00

ping -l 408 -t 192.168.0.125

UNIX/Linux/Mac syntax UNIX/Linux/Mac example

arp -s <IP Address> <Serial Number> temp

ping -s 408 <IP Address> arp -s 192.168.0.125 00:40:8c:18:10:00

temp

ping -s 408 192.168.0.125

Page 16 AXIS 211W Installation Guide

Unit connectors

Antenna connector - Reverse SMA connector for antenna.

Network connector - RJ-45 Ethernet connector. Supports Power over Ethernet. Using

shielded cables is recommended.

Power connector - Mini DC connector. 7 - 20V DC, max 5W. See product label for ±

connection.

Audio in - 3.5mm input for a mono microphone, or a line-in mono signal (left channel is

used from a stereo signal).

Audio out - Audio output (line level) that can be connected to a public address (PA) system

or an active speaker with a built-in amplifier. A pair of headphones can also be attached. A

stereo connector must be used for the audio out.

I/O terminal connector - Used in applications for e.g.

motion detection, event triggering, time lapse recording

and alarm notifications. It provides the interface to:

• 1 transistor output - For connecting external

devices such as relays and LEDs. Connected

devices can be activated by AXIS VAPIX AP,

output buttons on the Live View page or by

an Event Type. The output will show as

active (shown under Event Configuration >

Port Status) if the alarm device is activated.

• 1 digital input - An alarm input for connect-

ing devices that can toggle between an open and closed circuit, for example:

PIRs, door/window contacts, glass break detectors, etc. When a signal is received

the state changes and the input becomes active (shown under Event Configura-

tion > Port Status).

• Auxiliary power and GND

Function Pin number Notes Specifications

GND 1 Ground

5VDC Power 2 Can be used to power auxiliary equipment

(7-20VDC) or as a +5VDC (100mA) output.

Max load = 100mA

Digital Input 3 Connect to GND to activate, or leave float-

ing (or unconnected) to deactivate.

Must not be exposed to

voltages greater than

20VDC

Transistor

Output

4 Connects to GND when activated. If used

with an external relay, a diode must be con-

nected in parallel with the load for protec-

tion against voltage transients.

Max load = 100mA

Max voltage = 24VDC

(to the transistor)

Pin 1

Pin 3

Pin 2

Pin 4

Terminal connector. Note that the pins

are numbered 1-4, right to left.

AXIS 211W Installation Guide Page 17

ENGLISH

Connection diagram

LED indicators

LED Color Indication

Wireless Green Steady for connection to a wireless network. Flashes for network activity.

Red Steady for no wireless network connection. Flashes when scanning for wireless net-

works.

Unlit Wired mode.

Network Green Steady for connection to a 100 Mbit/s network. Flashes for network activity.

Amber Steady for connection to 10 Mbit/s network. Flashes for network activity.

Unlit No network connection.

Status Green Steady green for normal operation.

Note: The Status LED can be configured to be unlit during normal operation, or to

flash only when the camera is accessed. To configure, go to Setup > System

Options > LED settings. See the online help files for more information.

Amber Steady during startup, during reset to factory default or when restoring settings.

Red Slow flash for failed upgrade.

Power Green Normal operation.

Amber Flashes green/amber during firmware upgrade.

AXIS 211W

max. 100mA

e.g. pushbutton

Page 18 AXIS 211W Installation Guide

Resetting to the Factory Default Settings

This will reset all parameters, including the IP address, to the Factory Default settings:

1. Disconnect power from the camera.

2. Press and hold the Control button and reconnect power.

3. Keep the Control button pressed until the Status indicator displays amber (this may take

up to 15 seconds), then release the button.

4. When the Status indicator displays green (which can take up to 1 minute) the process is

complete and the camera has been reset.

5. Re-assign the IP address, using one of the methods described in this document.

It is also possible to reset parameters to the original factory default settings via the web

interface. For more information, please see the online help or the user’s manual.

Further information

The user’s manual is available from the Axis Web site at www.axis.com or from the Axis

Network Video Product CD supplied with this product.

Tip!

Visit www.axis.com/techsup to check if there is updated firmware available for your

AXIS 211W. To see the currently installed firmware version, see the Basic

Configuration web page in the product’s Setup tools.

Guide d'installation de l'appareil AXIS 211W Page 19

FRANÇAIS

FRANÇAIS FRANCAIS

AXIS 211W

Guide d'installation

Ce Guide d'installation vous explique comment installer l'appareil Caméra réseau

AXIS 211W sur votre réseau. Pour d'autres informations sur l'utilisation de ce produit,

consultez le Manuel de l'utilisateur, disponible sur le CD fourni ou sur www.axis.com/

techsup.

Étapes de l'installation

1. Vérifiez le contenu de la livraison à l'aide de la liste ci-dessous.

2. Présentation du matériel. Reportez-vous à la page 20.

3. Installez le matériel. Reportez-vous à la page 21.

4. Paramétrez une adresse IP. Reportez-vous à la

page 22.

5. Définissez le mot de passe. Reportez-vous à la

page 25.

6. Configurez la connexion sans fil. Reportez-vous à

la page 26.

7. Réglez la mise au point. Reportez-vous à la

page 30.

Contenu de l'emballage

Article Modèles/variantes/remarques

Caméra réseau AXIS 211W avec antenne

Alimentation (intérieur)

secteur PS-K

(dépend du pays)

Europe

Royaume-Uni

Australie

États-Unis/Japon

Argentine

Corée

Connecteur pour terminaux Connecteur 4 broches pour la connexion d'équipements externes au terminal

E/S

Pied de la caméra Fourni avec des vis de montage

CD CD AXIS Network Video Product avec la documentation du produit, les outils

d'installation et d'autres logiciels

Documentation imprimée AXIS 211W Guide d'installation (le présent document)

Document de garantie d'Axis

Important !

Ce produit doit être utilisé

conformément aux lois et

dispositions locales en

vigueur.

Page 20 Guide d'installation de l'appareil AXIS 211W

Présentation du matériel

Dimensions

H x L x P = 38 x 88 x 180 mm (1,5" x 3,5" x 7")

Poids = 260 g (0,57 lb) (sans antenne)

Témoin DEL de réseau

Connecteur

de réseau

Témoin DEL d'alimentation

Voyant d'état et

Microphone interne

Antenne

Face arrière

Vue de dessous

Numéro de série

Bouton de commande

Mise au point

Zoom avant/arrière

Câble de commande

de l'iris DC

Connecteur

pour

terminaux

E/S

Connecteur

E/S

Témoin DEL sans fil

Antenne

E/S

Sortie audio

Entrée audio

La page charge ...

Axis 211W Manuel utilisateur

Marque: Axis

Modèle: 211W

Catégorie: Des caméras de sécurité

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

Documents connexes

Autres documents

Axis Communications Q1604-E Manuel utilisateur