Lincoln Electric Flux Core 90i 120V Welder Le manuel du propriétaire

Marque: Lincoln Electric

Modèle: Flux Core 90i 120V Welder

Catégorie: Système de soudage

Taper: Le manuel du propriétaire

Ce manuel convient également à

K5255-1

Operator’s Manual

IMT10639 | *TTVF D ate +VO - 22

For use with Product Numbers:

13397

WELD-PAK 90i FC

www.lincolnelectric.com/register

Authorized Service and Distributor Locator:

www.lincolnelectric.com/locator

Save for future reference

Date Purchased

Code: (ex: 10859)

Serial: (ex: U1060512345)

Need Help? Call 1.888.935.3877

to talk to a Service Representative

Hours of Operation:

8:00 AM to 6:00 PM (ET) Mon. thru Fri.

After hours?

Use “Ask the Experts” at lincolnelectric.com

A Lincoln Service Representative will contact you

no later than the following business day.

For Service outside the USA:

Email: [email protected]

THANK YOU FOR SELECTING

A QUALITY PRODUCT BY

LINCOLN ELEC TRIC.

PLEASE EXAMINE CARTON AND EQUIPMENT FOR

DAMAGE IMMEDIATELY

When this equipment is shipped, title passes to the purchaser

upon receipt by the carrier. Consequently, claims for material

damaged in shipment must be made by the purchaser against the

transportation company at the time the shipment is received.

SAFETY DEPENDS ON YOU

Lincoln arc welding and cutting equipment is designed and built

with safety in mind. However, your overall safety can be increased

by proper installation ... and thoughtful operation on your part.

DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT

WITHOUT READING THIS MANUAL AND THE SAFETY

PRECAUTIONS CONTAINED THROUGHOUT. And, most importantly,

think before you act and be careful.

This statement appears where the information must be followed

exactly to avoid serious personal injury or loss of life.

This statement appears where the information must be followed

to avoid minor personal injury or damage to this equipment.

KEEP YOUR HEAD OUT OF THE FUMES.

DON’T get too close to the arc.

Use corrective lenses if necessary

to stay a reasonable distance

away from the arc.

READ and obey the Safety Data

Sheet (SDS) and the warning label

that appears on all containers of

welding materials.

USE ENOUGH VENTILATION or

exhaust at the arc, or both, to

keep the fumes and gases from

your breathing zone and the general area.

IN A LARGE ROOM OR OUTDOORS, natural ventilation may be

adequate if you keep your head out of the fumes (See below).

USE NATURAL DRAFTS or fans to keep the fumes away

from your face.

If you de velop unusual symptoms, see your supervisor.

Perhaps the welding atmosphere and ventilation system

should be checked.

WEAR CORRECT EYE, EAR &

BODY PROTECTION

PROTECT your eyes and face with welding helmet

properly fitted and with proper grade of filter plate

(See ANSI Z49.1).

PROTECT your body from welding spatter and arc

flash with protective clothing including woolen

clothing, flame-proof apron and gloves, leather

leggings, and high boots.

PROTECT others from splatter, flash, and glare

with protective screens or barriers.

IN SOME AREAS, protection from noise may be appropriate.

BE SURE protective equipment is in good condition.

Also, wear safety glasses in work area

AT ALL TIMES.

SPECIAL SITUATIONS

DO NOT WELD OR CUT containers or materials which previously

had been in contact with hazardous substances unless they are

properly cleaned. This is extremely dangerous.

DO NOT WELD OR CUT painted or plated parts unless special

precautions with ventilation have been taken. They can release

highly toxic fumes or gases.

Additional precautionary measures

PROTECT compressed gas cylinders from excessive heat,

mechanical shocks, and arcs; fasten cylinders so they cannot fall.

BE SURE cylinders are never grounded or part of an

electrical circuit.

REMOVE all potential fire hazards from welding area.

ALWAYS HAVE FIRE FIGHTING EQUIPMENT READY FOR

IMMEDIATE USE AND KNOW HOW TO USE IT.

WARNING

CAUTION

6DIHW\RI

SECTION A:

WARNINGS

CALIFORNIA PROPOSITION 65 WARNINGS

WARNING: Breathing diesel engine exhaust

exposes you to chemicals known to the State

of California to cause cancer and birth defects,

or other reproductive harm.

• Always start and operate the engine in a

well-ventilated area.

• If in an exposed area, vent the exhaust to the outside.

• Do not modify or tamper with the exhaust system.

• Do not idle the engine except as necessary.

For more information go to

www.P65 warnings.ca.gov/diesel

WARNING: This product, when used for welding or

cutting, produces fumes or gases which contain

chemicals known to the State of California to cause

birth defects and, in some cases, cancer. (California

Health & Safety Code § 25249.5 et seq.)

WARNING: Cancer and Reproductive Harm

www.P65warnings.ca.gov

ARC WELDING CAN BE HAZARDOUS. PROTECT

YOURSELF AND OTHERS FROM POSSIBLE SERIOUS

INJURY OR DEATH. KEEP CHILDREN AWAY.

PACEMAKER WEARERS SHOULD CONSULT WITH

THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For

additional safety information, it is strongly recommended

that you purchase a copy of “Safety in Welding & Cutting -

ANSI Standard Z49.1” from the American Welding Society,

P.O. Box 351040, Miami, Florida 33135 or CSA Standard

W117.2. A Free copy of “Arc Welding Safety” booklet E205

is available from the Lincoln Electric Company, 22801

St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION,

MAINTENANCE AND REPAIR PROCEDURES ARE

PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

FOR ENGINE POWERED

EQUIPMENT.

1.a. Turn the engine off before troubleshooting

and maintenance work unless the

maintenance work requires it to be running.

1.b. Operate engines in open, well-ventilated areas or vent the engine

exhaust fumes outdoors.

arc or when the engine is running. Stop the

engine and allow it to cool before refueling to

prevent spilled fuel from vaporizing on contact

tank. If fuel is spilled, wipe it up and do not start engine until

fumes have been eliminated.

1.d. Keep all equipment safety guards, covers

and devices in position and in good repair.

Keep hands, hair, clothing and tools away

from V-belts, gears, fans and all other

moving parts when starting, operating or

repairing equipment.

1.e. In some cases it may be necessary to remove safety guards to

perform required maintenance. Remove guards only when

necessary and replace them when the maintenance requiring

their removal is complete. Always use the greatest care when

working near moving parts.

1.f. Do not put your hands near the engine fan. Do not attempt to

override the governor or idler by pushing on the throttle control

rods while the engine is running.

1.g. To prevent accidentally starting gasoline engines while turning

the engine or welding generator during maintenance work,

disconnect the spark plug wires, distributor cap or magneto wire

as appropriate.

1.h. To avoid scalding, do not remove the radiator

pressure cap when the engine is hot.

ELECTRIC AND

MAGNETIC FIELDS MAY

BE DANGEROUS

causes localized Electric and Magnetic Fields (EMF).

and welding machines

welders having a pacemaker should consult their physician

before welding.

which are now not known.

2.d. All welders should use the following procedures in order to

2.d.1. Route the electrode and work cables together - Secure

them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and work

cables. If the electrode cable is on your right side, the

work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as pos-

sible to the area being welded.

2.d.5. Do not work next to welding power source.

SAFETY

Safety 02 of 04 - 10/08/2021

1.c. Do not add the fuel near an open ame welding

with hot engine parts and igniting. Do not spill fuel when lling

2.a. Electric current owing through any conductor

Welding current creates EMF elds around welding cables

2.b. EMF elds may interfere with some pacemakers, and

2.c. Exposure to EMF elds in welding may have other health effects

minimize exposure to EMF elds from the welding circuit:

1.i. Using a generator indoors CAN KILL YOU IN

MINUTES.

1.j. Generator exhaust contains carbon monoxide. This is a poison

you cannot see or smell.

1.k. NEVER use inside a home or garage,

EVEN IF doors and windows are open.

1.l. Only use OUTSIDE and far away from

windows, doors and vents.

1.m. Avoid other generator hazards. READ

MANUAL BEFORE USE.

ELECTRIC SHOCK

CAN KILL.

3.a. The electrode and work (or ground) circuits are

electrically “hot” when the welder is on. Do

not touch these “hot” parts with your bare skin or wet clothing.

Wear dry, hole-free gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.

Make certain the insulation is large enough to cover your full area

of physical contact with work and ground.

In addition to the normal safety precautions, if

welding must be performed under electrically

hazardous conditions (in damp locations or while

wearing wet clothing; on metal structures such as

floors, gratings or scaffolds; when in cramped

positions such as sitting, kneeling or lying, if there

is a high risk of unavoidable or accidental contact

with the workpiece or ground) use the following

equipment:

• Semiautomatic DC Constant Voltage (Wire) Welder.

• DC Manual (Stick) Welder.

• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,

electrode reel, welding head, nozzle or semiautomatic welding

gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electrical

connection with the metal being welded. The connection should

be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical (earth)

ground.

3.f. Maintain the electrode holder, work clamp, welding cable and

welding machine in good, safe operating condition. Replace

damaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts of electrode

holders connected to two welders because voltage

between the

two can be the total of the open circuit voltage of both

welders.

3.i. When working above floor level, use a safety belt to protect

yourself from a fall should you get a shock.

3.j. Also see It ems 6.c. and 8.

ARC RAYS CAN BURN.

4.a. Use a shield with the proper filter and cover plates to protect your

eyes from sparks and the rays of the arc when welding or

observing open arc welding. Headshield and filter lens should

conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant material

to protect your skin and that of your helpers from the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammable

screening and/or warn them not to watch the arc nor expose

themselves to the arc rays or to hot spatter or metal.

FUMES AND GASES

CAN BE DANGEROUS.

5.a. Welding may produce fumes and gases

hazardous to health. Avoid breathing these

fumes and gases. When welding, keep your head out of the fume.

Use enough ventilation and/or exhaust at the arc to keep fumes

and gases away from the breathing zone. When welding

hardfacing (see instructions on container or SDS)

or on lead or cadmium plated steel and other

metals or coatings which produce highly toxic

fumes, keep exposure as low as possible and

within applicable OSHA PEL and ACGIH TLV limits

using local exhaust or mechanical ventilation

unless exposure assessments indicate otherwise.

In confined spaces or in some circumstances,

outdoors, a respirator may also be required.

Additional precautions are also required when

welding

on galvanized steel.

5. b. The operation of welding fume control equipment is affected by

various factors including proper use and positioning of the

equipment, maintenance of the equipment and the specific

welding procedure and application involved. Worker exposure

level should be checked upon installation and periodically

thereafter to be certain it is within applicable OSHA PEL and

ACGIH TLV limits.

5.c. Do not weld in locations near chlorinated hydrocarbon vapors

coming from degreasing, cleaning or spraying operations. The

heat and rays of the arc can react with solvent vapors to form

phosgene, a highly toxic gas, and other irritating products.

5.d. Shielding gases used for arc welding can displace air and

cause

injury or death. Always use enough ventilation, especially in

confined areas, to insure breathing air is safe.

5.e. Read and understand the manufacturer’s instructions for this

equipment and the consumables to be used, including the

Safety Data Sheet (SDS) and follow your employer’s safety

practices. SDS forms are available from your welding

distributor or from the manufacturer.

5.f. Also see item 1.b.

SAFETY

6DIHW\RI

WELDING AND CUTTING

SPARKS CAN CAUSE

FIRE OR EXPLOSION.

6.a. Remove fire hazards from the welding area. If

this is not possible, cover them to prevent the welding sparks

from starting a fire. Remember that welding sparks and hot

materials from welding can easily go through small cracks and

openings to adjacent areas. Avoid welding near hydraulic lines.

Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site, special

precautions should be used to prevent hazardous situations.

Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1)

and the operating information for the equipment being used.

6.c. When not welding, make certain no part of the electrode circuit is

touching the work or ground. Accidental contact can cause

overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the

proper steps have been taken to insure that such procedures

will not cause flammable or toxic vapors from substances inside.

They can cause an explosion even though they have been

“cleaned”. For information, purchase “Recommended Safe

Practices for the Preparation for Welding and Cutting of

Containers and Piping That Have Held Hazardous Substances”,

AWS F4.1 from the American Welding Society

(see address above).

6.e. Vent hollow castings or containers before heating, cutting or

welding. They may explode.

6.f. Sparks and spatter are thrown from the welding arc. Wear oil free

protective garments such as leather gloves, heavy shirt, cuffless

trousers, high shoes and a cap over your hair. Wear ear plugs

when welding out of position or in confined places. Always wear

safety glasses with side shields when in a welding area.

6.g. Connect the work cable to the work as close to the welding area

as practical. Work cables connected to the building framework or

other locations away from the welding area increase the

possibility of the welding current passing through lifting chains,

crane cables or other alternate circuits. This can create fire

hazards or overheat lifting chains or cables until they fail.

6.h. Also see item 1.c.

6.I. Read and follow NFPA 51B “Standard for Fire Prevention During

Welding, Cutting and Other Hot Work”, available from NFPA, 1

Batterymarch Park, PO box 9101, Quincy, MA 022690-9101.

6.j. Do not use a welding power source for pipe thawing.

CYLINDER MAY EXPLODE IF

DAMAGED.

7.a. Use only compressed gas cylinders containing

the correct shielding gas for the process used

and properly operating regulators designed for

the gas and pressure used. All hoses, fittings,

etc. should be suitable for the application and

maintained in good condition.

7.b. Always keep cylinders in an upright position securely chained to

an undercarriage or fixed support.

7.c. Cylinders should be located:

• Away from areas where they may be struck or subjected

to physical damage.

• A safe distance from arc welding or cutting operations

and any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other

electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet

when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand tight

except when the cylinder is in use or connected for use.

7.g. Read and follow the instructions on compressed gas cylinders,

associated equipment, and CGA publication P-l, “Precautions for

Safe Handling of Compressed Gases in Cylinders,” available from

the Compressed Gas Association, 14501 George Carter Way

Chantilly, VA 20151.

FOR ELECTRICALLY

POWERED EQUIPMENT.

8.a. Turn off input power using the disconnect

switch at the fuse box before working on

the equipment.

8.b. Install equipment in accordance with the U.S. National Electrical

Code, all local codes and the manufacturer’s recommendations.

8.c. Ground the equipment in accordance with the U.S. National

Electrical Code and the manufacturer’s recommendations.

Refer to

http://www.lincolnelectric.com/safety

for additional safety information.

SAFETY

6DIHW\RI

WELD-PAK 90i FC

TABLE OF CONTENTS

Installation ................................................................................................................................................................ 

Technical Specifications................................................................................................................................................

Premium Features.........................................................................................................................................................

Select Suitable Location................................................................................................................................................

Grinding ................................................................................................................................................................

Stacking ................................................................................................................................................................

Transport – Unloading ..................................................................................................................................................

Tilting ................................................................................................................................................................ 

Environmental Rating .................................................................................................................................................



Input Connections .....................................................................................................................................................

...



Wire Loading And Threading.........................................................................................................................................

Operation ................................................................................................................................................................ 

Operating Machine .....................................................................................................................................................

Replacement Parts Lists..............................................................................................................................................

Maintenance.............................................................................................................................................................1

Routine And Periodic Maintenance ....................................................................................................................

.........1



Troubleshooting........................................................................................................................................................1

How To Use Troubleshooting Guide.............................................................................................................................1

1SPEVDU%FTDSJQUJPO ................................................................................................................................................... 3



INSTALLATIONWELD-PAK 90i FC

130%6$5%&4$3*15*0/

130%6$546.."3:

5IF8FME1BL¥J'$JTBDPOTUBOUWPMUBHF%$XFMEJOHNBDIJOF

SBUFEGPSBNQTWPMUTBUBEVUZDZDMF5IF8FME1BL¥

VOJUJTJOUFOEFEGPSGBCSJDBUJPONBJOUFOBODFIPNFBOEBVUPCPEZ

TIPQT5IFVOJUGFBUVSFTBQPSUBCMFBOESVHHFEDBTF5IFVTFS

JOUFSGBDFGFBUVSFTUXPLOPCTPOFGPSWPMUBHFBOEPOFGPSXJSFGFFE

TQFFE5IF8FME1BL¥J'$JTEFTJHOFEGPSUIF/PSUI"NFSJDBO

NBSLFUBOEPQFSBUFTPO7TJOHMFQIBTF)[QPXFS"O

PWFSWJFXPGUIFNBDIJOFTJOQVUBOEPVUQVUDBQBCJMJUJFTBSFMJTUFE

POUIFSBUJOHQMBUFTIPXOIFSF

5IFNBDIJOFDPNFTXJUIUIFGPMMPXJOHBDDFTTPSJFT

v 81-HVO

v 8PSLDBCMFXJUIDMBNQ

v 4QBSFDPOUBDUUJQT

v 1SPDFEVSF$IBSUBOEMJUFSBUVSF



INSTALLATIONWELD-PAK 90i FC

INSTALLATION

TECHNICAL SPECIFICATIONS -

K5255-1 WELD-PAK 90i FC

PREMIUM FEATURES INCLUDE:

1. Inverter power source – more efcient to operate, provides

smoother weld characteristics than traditional welders

2. Innite welding voltage to allow ne tuning of weld charac-

teristics

3. 30% Duty cycle at 90 Amps

4. Lightweight and portable – Ideal for maintenance and mobile

welders

THERMAL PROTECTION

The machine has a maximum output duty cycle of 30%. If the duty

cycle is exceeded, a thermal protector will shut off the output until

the machine cools to a normal operating temperature. This is an

automatic function of the machine and does not require user inter-

vention.

REQUIRED ACCESSORIES

• Helmet

• Jacket

• Gloves

OUTPUT CURRENT RANGE

30-12A

OPEN CIRCUIT VOLTAGE

V (RMS)

INPUT CIRCUIT

120VAC

DUTY CYCLE

30%@90A

WIREFEED SPEED

0 - 200 IPM

SUITABLE WIRE DIAMETER

0.030”, 0.035”

GROSS WEIGHT

15 LBS (7KGS)

IPS RATING

IP21S



INSTALLATIONWELD-PAK 90i FC

Read this entire installation section before you start

installation.

Safety Precautions

Do not attempt to use this equipment until you have

thoroughly read all installation, operating and maintenance

information supplied with your equipment. They include

important safety precautions and detailed operating and

maintenance instructions.

ELECTRIC SHOCK can kill.

• Only qualied personnel should

perform this installation.

• Do not touch electrically live parts.

• Always connect the machine to an

earthed mains supply.

SELECT SUITABLE LOCATION

Place the welder where clean cooling air can freely circulate in

and out of the front & rear louver vents. Dirt, dust or any foreign

material that can be drawn through vents into welder must be

kept to a minimum. Failure to observe these precautions can

result in excessive operating temperatures which can lead to plant

failure.

GRINDING

Do not direct grinding particles towards the welder. An abundance

of conductive material can cause plant failure.

STACKING

This machine cannot be stacked.

TRANSPORT - UNLOADING

Never underestimate the weight of equipment, never move or

leave suspended in the air above people. The machine should

be lifted and carried by the provided strap, or by cradling the

machine. The machine should not be carried by the input, cord,

output cables, or welding gun. Utilize proper lifting techniques

when carrying or lifting the machine to prevent injury.

Falling Equipment can cause

injury. Never lift welder with gas

bottle attached. Never lift above

personnel.

TILTING

Machine must be placed on a secure level surface

ENVIRONMENTAL RATING

The welding power source carries the IP21S rating. It may be used

in normal industrial and commercial environments. Avoid using in

areas where water / rain is around.

Read and follow the ‘Electric Shock Warnings’ in the safety section

if welding must be performed under electrically hazardous

conditions such as welding in wet areas or water on the work

piece.

ELECTRIC SHOCK can kill.

• This welder must be grounded to earth

The high frequency generator being

similar to a radio transmitter may

cause interference to radio, TV and

other electronic equipment.

• These problems may be the result of

radiated interference. Proper grounding methods can

reduce or eliminate this.

Radiated interference can develop in the following ways

1. Direct interference from welder power source

2. Direct interference from the welding leads

3. Direct interference radiated from feedback into power lines

4. Interference from re-radiation by un-grounded metallic

objects

Keeping these contributing factors in mind, installing equipment

as per following instructions should minimize problems

1. Keep the welder input power lines as short as possible and

enclose as much of them as possible in metal conduit or

equivalent shielding. There should be a good electrical

contact between this conduit and ground (Earth)

2. Keep the work and electrode leads as short as possible. Tape

the leads together where practical

3. Be sure the torch and earth leads rubber coverings are free

from cuts and cracks that allow welding power leakage

4. Keep earth lead connection to work in good condition – Clean

area on workbench where earth clamp is situated on a

regular basis.

WARNING

CAUTION



INSTALLATIONWELD-PAK 90i FC

INPUT POWER CONNECTION

The machine has one input connection, the power input cable. The

power input cable is located on the rear.

The Weld-Pak 90i FC is provided with a 120V cable, 6.0ft. (1.8m)

in length, with a 15Amp 5-15P plug molded onto the cord.

The rated output of the Weld-Pak 90i FC is available when

connected to a 20A branch circuit. When connected to a branch

circuit with lower capacity, lower welding current and duty cycle

must be used.

CODE REQUIREMENTS FOR ELECTRICAL INPUT

CONNECTIONS

This welding machine must be connected to a power source

in accordance with applicable electrical codes.

The National Electrical Code provides standards for amperage

handling capability of supply conductors based on duty cycle of

the welding source.

If there is any question about the installation meeting applicable

electrical code requirements, consult a qualied electrician.

Do not connect the machine to an input power supply with a

rated voltage that is greater than 125 volts.

Do not remove the power cord ground prong.

EXTENSION CORD USAGE

If an extension cord is required, use one that is rated for the

application and is 3 conductor #14 AWG (2.1 mm2) or larger. The

recommended maximum lengths are 25 ft (7.5 m) if #14 AWG (2.1

mm2) is used and 50 ft (15 m) if #12 AWG (3.3 mm2) is used.

FLUX-CORED (INNERSHIELD) WELDING

The recommended electrode for the ux-cored, self-shielded

process is 0.035” (0.9 mm) diameter Lincoln Innershield

NR-211-MP on 1 lbs. (.5 kg) spools.

FIGURE 1

1. Adjustment for Voltage

2. Adjustment for Wire feed speed

3. Power and protection LEDs

4. Gasless Flux-Cored torch

5. Work Clamp

6. Power Switch

7. Power Input Cable

8. Spool cover latch

WARNING



INSTALLATIONWELD-PAK 90i FC

WIRE LOADING AND THREADING

R e fer to F igure 2.

Turn machine power switch to the OFF (“0”) position before

working inside the wire feed enclosure.

Make sure that the wire feed drive roll and the contact tip of the

gun match the diameter and type of wire used.

1. Push the spool onto the spindle so that the wire feeds off the

bottom of the spool, toward the drive roll.

2. Push the spool spacer onto the spindle, against the spool.

3. Slide the spring onto the spool, then press on the spool lock,

turning it clockwise to lock the spool assembly onto the

spindle.

FIGURE 2

WIRE THREADING DETAILS

R efer to F igure 3.

4. Release the spring loaded thumb screw and rotate the idle roll

arm away from the wire feed drive roll. Ensure that the

visible, stenciled size on the drive roll side facing you

matches the wire size being used.

5. Carefully detach the end of the wire from the spool. Maintain

tension on the wire to prevent the spool from unwinding and

do not release the wire until after step 5.

mm).

7. Thread the wire through the incoming guide tube, over the

drive roll, and into the gun liner.

8. Close the idle roll arm and turn down the thumbscrew until

release the welding wire). Make sure the wire is positioned in

the groove of the lower drive roll.

9. The spring loaded thumbscrew on the idle roll arm adjusts

the pressure on the wire. Adjust pressure by turning the

thumbscrew to prevent spool overrun, but still allow smooth

and easy wire feeding. Start with the pressure set to an inter-

mediate value. Readjust, if necessary. If the drive roll slips

while feeding wire, the pressure should be increased until the

wire feeds properly.

FIGURE 3

Spool Lock & Spring Cap

Spool Spacer

Spool

Note Wire Direction

Spindle

Spring Loaded Thumb Screw

Ingoing Guide Tube

Wire Feed Drive Roll

Idle Arm

Cold Feed Switch



INSTALLATIONWELD-PAK 90i FC

WIRE STICKOUT

10. Remove the contact tip and nozzle from the gun.

11. Turn the machine ON (“I”).

12. Straighten the gun cable assembly.

13. Depress the cold feed switch and feed welding wire through

the gun and cable. (Point the gun away from yourself and

others while feeding wire). Release the cold feed switch after

wire appears at the end of the gun.

14. Turn off the machine.

15. Replace the nozzle and contact tip. Refer to Figure B-4. Cut

the wire off so that 3/8” to 5/8” (10 - 15 mm) protrudes from

the end of the tip.

16. Turn on the machine. The machine is now ready to weld.

FIGURE 4

CONTACT

TIP

WIRE

ELECTRODE

3/8" to 5/8" Contact Tip

To Work Distance

(CTWD)



OPERATION

Read and understand this entire section before operating

your CrossLinc Remote.

WELD-PAK 90i FC

GRAPHIC SYMBOLS USED IN THIS MANUAL

OR BY THIS MACHINE



OPERATION

snoituacerP ytefaS

Do not attempt to use this equipment until you have

thoroughly read all operating and maintenance manuals

supplied with your equipment and any related welding

machine it will be used with. They include important safety

precautions, operating and maintenance instructions and

parts lists.

ELECTRIC SHOCK can kill.

• Do not touch electrically live parts such as

output terminals or internal wiring.

• Insulate yourself from the work and

ground.

• Always wear dry insulating gloves.

or explosion.

• Do not weld upon containers which have

held combustibles.

ARC RAYS can burn.

• Wear eye, ear and body protection.

FUMES AND GASES can

be dangerous.

Although the removal of the particulate

matter from welding smoke may reduce

the ventilation requirement, concentrations

of the clear exhausted fumes and gases may still be

hazardous to health. Avoid breathing concentrations of

these fumes and gases. Use adequate ventilation when

welding. See ANSI Z49.1, "Safety in Welding and Cutting",

published by the American Welding Society.

OPERATING MACHINE

Once you have set machine up as per instructions, refer to Table

B.1 and the Procedure Decal located on the inside of the wire

drive compartment door of your machine for setup information,

consumables, and quick tips for welding.

1. Select welding voltage (power), based on the material

thickness of the work piece, required on front panel

2. Select wire feed speed required on ‘wire speed’ knob

3. Ensure you are wearing the correct safety clothes &

equipment for welding (I.E Welding mask, gloves, apron etc)

FIGURE 5

4. Connect the work clamp to the metal to be welded. The work

clamp must make good electrical contact to the work piece.

The work piece must also be grounded as stated in Arc

Welding Safety Precautions in the beginning of this manual.

5. Based on the weld joint type and orientation of the weld joint,

position the gun into the joint at the correct angle.

6. To begin welding, raise your hand shield or lower your

helmet to protect your eyes and pull the trigger.

7. While welding, travel at a constant speed and maintain an

electrode stickout of 3/8".

8. To stop welding, release the gun trigger.

9. When no more welding is to be done, turn off the machine.

WARNING

Gun Cable

Workpiece

Work Clamp

WELD-PAK 90i FC



OPERATION

TABLE B.1

REPLACE PARTS LIST

Use of this unit on thicker materials than recommended may

result in welds of poor quality. The welds may appear to be

strong weld. This is called "Cold Casting" or "cold lapping"

and is some what similar to a cold solder joint. Weld failure

may result.

Contact Tip (.035”) KH712 (.035” / 0.9MM)

Drive Roll KP4364-035

Nozzle KH726

FCAW Wire LINCOLN .030 NR-211-MP

WARNING

WELD-PAK 90i FC

Welding Wire

Contact Tip

Drive Roll

Horizontal: "Drag"

Tee Joint

Maintain an electrode Stickout

of 3/8" while welding.

Wire Feed

Tension

.035 (0.9mm) - Lincoln Part No. KH712

The suggested Wire Feed Speed settings in the table below are based on a midrange wire tension

setting. The tension may be changed if required to improved wire feeding; however, the WFS setting may

have to be adjusted from the values in the table below.

Do NOT weave the arc, neither forward, backward, or sideways

FCAW -Gasless (Flux Cored)

.035 Lincoln NR-211-MP (Innershield Cored Wire)

Loading The

Wire

Suggested

Settings For

Welding

Remember: Remove the contact tip prior to loading wire

Keep tension on the wire to prevent unspooling.

2. Release spring loaded pressure arm and rotate the Idle Roll Arm away from Drive Roll.

3. Thread wire through the guide tube, over drive roll and into gun liner. Close Idle Roll arm.

Weld at a Steady Pace

Helpful Hints

For Horizontal Weld Joints, remember: "Drag if there’s Slag"

Refer to Manual for Troubleshooting Poor Weld Quality

Remove Slag with the Chipping Hammer to expose weld

Proper Gun

Angles for

common Weld

Joint Types

Direction of

Welding AND

Angle of Gun

relative to Weld

Direction

Electrical

Stickout

CONTACT TIP

ELECTRODE 3/8

ertical Down

Butt Joint Lap Joint

Vertical Up

45° 45°

.030 Lincoln NR-211-MP (Innershield Cored Wire)

.030 (0.8mm) - Lincoln Part No. KH711

0.030/0.035 (0.8mm/0.9mm) Knurled groove - Lincoln Part No. KP4364-035

20ga

0.9mm

18ga

1.2mm

16ga

1.6mm

14ga

2.1mm

1/8”ga

3.2mm

0.030 NR-

211

Voltage 1.5 2.5 3 4 6

WFS 3.5 5 7 8 10

0.035 NR-

211

Voltage --2346

WFS -- 3 4.5 6 10

NO GAS WITH NR-211

WIRE

Contact Tip (.030”) KH711 (.030” / 0.8MM)

FCAW Wire LINCOLN .035 NR-211-MP



TROUBLESHOOTING

WELD-PAK 90i FC

MAINTENANCE

ELECTRIC SHOCK can kill.

• Turn the input power OFF at the welding

power source before installation or

changing drive rolls and/or guides.

• Do not touch electrically live parts.

• When inching with the gun trigger, electrode and drive

mechanism are "hot" to work and ground and could

remain energized several seconds after the gun trigger

is released.

• Do not operate with covers, panels or guards removed

or open.

• Only qualified personnel should perform maintenance

work.

ITEMS REQUIRING NO MAINTENANCE

• Drive Motor and Gearbox – Lifetime lubrication

• Wire Reel Spindle – Do NOT lubricate shaft

ROUTINE AND PERIODIC MAINTENANCE

•BEFORE EACH USE - Check over machine and

accessories for any obvious condition that may prevent safe

performance or operation. Repair or replace items as

necessary to correct any abnormal condition.

AFTER 5 MINUTES OF WELDING OR WHEN SPATTER

ACCUMULATES ON THE CONTACT TIP:

•CLEANING TIP AND NOZZLE - With the power

switch in the off position, keep the contact tip and nozzle

clean to avoid arc bridging between them. Bridging can

result in a shorted nozzle, poor welds and an overheated gun.

Hint: Anti-stick spray or gel, available from a welding

supplier, may reduce buildup and aid in spatter removal.

TROUBLESHOOTING

HOW TO USE TROUBLESHOOTING GUIDE

Service and Repair should only be performed by Lincoln

Electric Factory Trained Personnel. Unauthorized repairs

performed on this equipment may result in danger to the

technician and machine operator and will invalidate your

factory warranty. For your safety and to avoid Electrical

Shock, please observe all safety notes and precautions

detailed throughout this manual.

This Troubleshooting Guide is provided to help you locate and

repair possible machine malfunctions. Simply follow the three-

step procedure listed below.

Step 1. LOCATE PROBLEM (SYMPTOM).

Look under the column labeled “PROBLEM (SYMPTOMS).” This

column describes possible symptoms that the machine may

exhibit. Find the listing that best describes the symptom that the

machine is exhibiting.

Step 2. POSSIBLE CAUSE.

The second column labeled “POSSIBLE CAUSE” lists the obvious

external possibilities that may contribute to the machine symptom.

Step 3. RECOMMENDED COURSE OF ACTION

This column provides a course of action for the Possible Cause,

generally it states to contact you local Lincoln Authorized Field

Service Facility.

If you do not understand or are unable to perform the

Recommended Course of Action safely, contact your local

Lincoln Authorized Field Service Facility.

ELECTRIC SHOCK can kill.

• Turn off machine at the disconnect switch

on the rear of the machine and remove

main power supply connections before

doing any troubleshooting.

WARNING



TROUBLESHOOTING

WELD-PAK 90i FC

Observe all Safety Guidelines detailed throughout this manual

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Lincoln Authorized Service Facility for technical troubleshooting assistance before you proceed.

WWW.LINCOLNELECTRIC.COM/LOCATOR

PROBLEM

(SYMPTOMS)

POSSIBLE AREAS OF

MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION

Bead is too thick (inter-

mittently).

Travel speed is slow and/or inconsistent. Increase and maintain a constant travel speed.

Output heat range is too high. Turn the voltage down.

Bead does not penetrate base

metal.

Travel speed is inconsistent. Decrease and maintain a constant travel speed.

Output heat range is too low. Turn the voltage up.

Wire sputters and sticks to

workpiece.

The wire is damp. Change to dry wire. Be sure wire is stored in a dry location

Wire feed speed (WFS) is too fast. Reduce WFS.

Edge of weld has ragged

depressions.

Travel speed is too fast. Reduce travel speed.

WFS is too fast. Reduce WFS.

Output heat range is too high. Set the Low – High Heat Range switch to Low or the Fine

Heat Adjustment to (1).



DIAGRAMS

AC1

AC2

3-4

12V

2 1

19 2

11 10

OUT +

OUT -

K 1 A C 120V /50/60HZ

RECITIFIER

REAR OF MACHINE

FRONT OF MACHINE

FAN

MOTOR

TORCH

3 4

WELD-PAK 90i FC

WARNING

AVISO DE

PRECAUCION

ATTENTION

WARNUNG

ATENÇÃO

Spanish

French

German

Portuguese

Japanese

Chinese

Korean

Arabic

READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE

USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.

SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE ESTE EQUIPO Y LOS

CONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.

LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT ET LES PRODUITS A

ETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE EMPLOYEUR.

LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRODENEINSATZ DES HER-

STELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS SIND EBENFALLS ZU BEACHTEN.

Do not touch electrically live parts or

electrode with skin or wet clothing.

 Insulate yourself from work and

ground.

No toque las partes o los electrodos

bajo carga con la piel o ropa moja-

da.

 Aislese del trabajo y de la tierra.

Ne laissez ni la peau ni des vête-

ments mouillés entrer en contact

avec des pièces sous tension.

 Isolez-vous du travail et de la terre.

 Berühren Sie keine stromführenden

Teile oder Elektroden mit Ihrem

Körper oder feuchter Kleidung!

 Isolieren Sie sich von den

Elektroden und dem Erdboden!

 Não toque partes elétricas e elec-

trodos com a pele ou roupa molha-

da.

 Isole-se da peça e terra.

Keep flammable materials away.

 Mantenga el material combustible

fuera del área de trabajo.

 Gardez à l’écart de tout matériel

inflammable.

 Entfernen Sie brennbarres Material!

 Mantenha inflamáveis bem guarda-

dos.

Wear eye, ear and body protection.

 Protéjase los ojos, los oídos y el

cuerpo.

 Protégez vos yeux, vos oreilles et

votre corps.

 Tragen Sie Augen-, Ohren- und Kör-

perschutz!

 Use proteção para a vista, ouvido e

corpo.

WARNING

AVISO DE

PRECAUCION

ATTENTION

WARNUNG

ATENÇÃO

Spanish

French

German

Portuguese

Japanese

Chinese

Korean

Arabic

LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES DE USO, E SIGA AS

PRÁTICAS DE SEGURANÇA DO EMPREGADOR.

Keep your head out of fumes.

 Use ventilation or exhaust to

remove fumes from breathing zone.

 Los humos fuera de la zona de res-

piración.

 Mantenga la cabeza fuera de los

humos. Utilice ventilación o

aspiración para gases.

 Gardez la tête à l’écart des fumées.

 Utilisez un ventilateur ou un aspira-

teur pour ôter les fumées des zones

de travail.

 Vermeiden Sie das Einatmen von

Schweibrauch!

 Sorgen Sie für gute Be- und

Entlüftung des Arbeitsplatzes!

 Mantenha seu rosto da fumaça.

 Use ventilação e exhaustão para

remover fumo da zona respiratória.

Turn power off before servicing.

 Desconectar el cable de ali-

mentación de poder de la máquina

antes de iniciar cualquier servicio.

 Débranchez le courant avant l’entre-

tien.

 Strom vor Wartungsarbeiten

abschalten! (Netzstrom völlig öff-

nen; Maschine anhalten!)

 Não opere com as tampas removidas.

 Desligue a corrente antes de fazer

serviço.

 Não toque as partes elétricas nuas.

Do not operate with panel open or

guards off.

 No operar con panel abierto o

guardas quitadas.

 N’opérez pas avec les panneaux

ouverts ou avec les dispositifs de

protection enlevés.

 Anlage nie ohne Schutzgehäuse

oder Innenschutzverkleidung in

Betrieb setzen!

 Mantenha-se afastado das partes

moventes.

 Não opere com os paineis abertos

ou guardas removidas.

La page charge ...

Lincoln Electric Flux Core 90i 120V Welder Le manuel du propriétaire

Marque: Lincoln Electric

Modèle: Flux Core 90i 120V Welder

Catégorie: Système de soudage

Taper: Le manuel du propriétaire

Ce manuel convient également à

K5255-1

Télécharger le PDF

rapport

dans d''autres langues

Documents connexes

Autres documents

Century FC-90 Manuel utilisateur