Yamaha SWR2100P-10G Le manuel du propriétaire
- Catégorie
- Équipement musical supplémentaire
- Taper
- Le manuel du propriétaire
L2 Switch
SWR2100P-10G
SWR2100P-5G
RU
IT
ES
FR
DE
EN
Owner’s Manual
Bedienungsanleitung
Mode d’emploi
Manual de instrucciones
Manuale di istruzioni
Руководство пользователя
EnglishDeutschFrançaisEspañolItalianoРусский
2SWR2100P-10G/SWR2100P-5G Owner’s Manual
Explanation of Graphical Symbols
Explication des symboles
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
L’éclair avec une flèche à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’une
« tension dangereuse » non isolée à l’intérieur de l’appareil, pouvant être suffisamment élevée pour constituer un risque d’électrocution.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.
Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’instructions
importantes sur l’emploi ou la maintenance (réparation) de l’appareil dans la documentation fournie.
IMPORTANT SAFETY
INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9 Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
(UL60065_03)
PRÉCAUTIONS CONCER-
NANT LA SÉCURITÉ
1 Lire ces instructions.
2 Conserver ces instructions.
3 Tenir compte de tous les avertissements.
4 Suivre toutes les instructions.
5 Ne pas utiliser ce produit à proximité d’eau.
6 Nettoyer uniquement avec un chiffon propre et sec.
7 Ne pas bloquer les orifices de ventilation. Installer l’appareil
conformément aux instructions du fabricant.
8 Ne pas installer l’appareil à proximité d’une source de chaleur
comme un radiateur, une bouche de chaleur, un poêle ou tout autre
appareil (y compris un amplificateur) produisant de la chaleur.
9 Ne pas modifier le système de sécurité de la fiche polarisée ou de
la fiche de terre. Une fiche polarisée dispose de deux broches dont
une est plus large que l’autre. Une fiche de terre dispose de deux
broches et d’une troisième pour le raccordement à la terre. Cette
broche plus large ou cette troisième broche est destinée à assurer
la sécurité de l’utilisateur. Si la fiche équipant l’appareil n’est pas
compatible avec les prises de courant disponibles, faire remplacer
les prises par un électricien.
10 Acheminer les cordons d’alimentation de sorte qu’ils ne soient pas
piétinés ni coincés, en faisant tout spécialement attention aux
fiches, prises de courant et au point de sortie de l’appareil.
11 Utiliser exclusivement les fixations et accessoires spécifiés par le
fabricant.
12 Utiliser exclusivement le chariot, le stand, le
trépied, le support ou la table recommandés par
le fabricant ou vendus avec cet appareil. Si
l’appareil est posé sur un chariot, déplacer le
chariot avec précaution pour éviter tout risque
de chute et de blessure.
13 Débrancher l’appareil en cas d’orage ou lorsqu’il
doit rester hors service pendant une période prolongée.
14 Confier toute réparation à un personnel qualifié. Faire réparer
l’appareil s’il a subi tout dommage, par exemple si la fiche ou le
cordon d’alimentation est endommagé, si du liquide a coulé ou des
objets sont tombés à l’intérieur de l’appareil, si l’appareil a été
exposé à la pluie ou à de l’humidité, si l’appareil ne fonctionne pas
normalement ou est tombé.
(UL60065_03)
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ATTENTION :
POUR RÉDUIRE LES RISQUES D'ÉLECTROCUTION, NE PAS RETIRER
LE CAPOT (OU LE DOS). NE CONTIENT PAS DE PIÈCES NÉCESSITANT
L'INTERVENTION DE L'UTILISATEUR. POUR TOUTE INTERVENTION,
FAIRE APPEL À DES PROFESSIONNELS QUALIFIÉS.
ATTENTION
RISQUE DE CHOC
ELECTRIQUE-NE PAS OUVRIR
The above warning is located on the top of the unit. L’avertissement ci-dessus est situé sur le dessus de l’unité.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
AVERTISSEMENT
POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE
ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À
L’HUMIDITÉ.
SWR2100P-10G/SWR2100P-5G Owner’s Manual 3
1. IMPORTANT NOTICE:
DO NOT MODIFY THIS UNIT!
This product, when installed as indicated
in the instructions contained in this man-
ual, meets FCC requirements. Modifica-
tions not expressly approved by Yamaha
may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT: When connecting this
product to accessories and/or another
product use only high quality shielded
cables. Cable/s supplied with this product
MUST be used. Follow all installation
instructions. Failure to follow instructions
could void your FCC authorization to use
this product in the USA.
3. NOTE: This product has been tested and
found to comply with the requirements
listed in FCC Regulations, Part 15 for
Class “A” digital devices. Compliance with
these requirements provides a reason-
able level of assurance that your use of
this product, in a commercial environment,
will not result in harmful interference with
other electronic devices. However, opera-
tion of this product in a residential area is
likely to cause interference in some form.
In this case you, the user, bear the respon-
sibility of correcting this condition.
This product generates/uses radio fre-
quencies and, if not installed and used
according to the instructions found in the
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class A)
users manual, may cause interference
harmful to the operation of other electronic
devices. Compliance with FCC regulations
does not guarantee that interference will
not occur in all installations. If this product
is found to be the source of interference,
which can be determined by turning the
product “OFF” and “ON”, please try to
eliminate the problem by using one of the
following measures:
Relocate either the product generating the
interference or the device that is being
affected by the interference.
Utilize power outlets that are on different
branch (circuit breaker or fuse) circuits or
install AC line filter/s.
In the case of radio or TV interference,
relocate/reorient the antenna. If the
antenna lead-in is 300 ohm ribbon lead,
change the lead-in to co-axial type cable.
If these corrective measures do not pro-
duce satisfactory results, please contact
the local retailer that is authorized to dis-
tribute this type of product. If you can not
locate the appropriate retailer, please con-
tact Yamaha Corporation of America, Elec-
tronic Service Division, 6600
Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to
those products distributed by Yamaha Cor-
poration of America or its subsidiaries.
FCC INFORMATION (U.S.A.)
PRECAUTIONS
4SWR2100P-10G/SWR2100P-5G Owner’s Manual
PRECAUTIONS
PLEASE READ CAREFULLY
BEFORE PROCEEDING
Please keep this manual in a safe
place for future reference.
WARNING
Always follow the basic precautions
listed below to avoid the possibility of
serious injury or even death from
electrical shock, short-circuiting,
damages, fire or other hazards. These
precautions include, but are not limited
to, the following:
Power supply/power cord
• Do not damage the power cable or the
LAN cable. Failure to observe this
precaution could result in fire, electric
shock, or damage to the product.
- Do not place heavy objects on the
cable.
- Do not process the cable in any way.
- Do not use staples to fix the cable in
place.
- Do not apply excessive force to the
cable.
- Be sure to keep the cable away from
anything hot.
• Only use the voltage specified as correct
for the device. The required voltage is
printed on the name plate of the device.
• Use only the supplied power cord/plug.
If you intend to use the device in an area
other than in the one you purchased, the
included power cord may not be
compatible. Please check with your
Yamaha dealer.
• Check the electric plug periodically and
remove any dirt or dust which may have
accumulated on it.
• When setting up the device, make sure
that the AC outlet you are using is easily
accessible. If some trouble or malfunction
occurs, immediately disconnect the plug
from the outlet. As long as the power cord
is not unplugged from the wall AC outlet,
the device will not be disconnected from
the power source.
• Be sure to fully and securely insert the
power plug into the AC outlet. If the power
plug is not fully inserted, use of this
product could cause an electric shock.
Also, the plug could collect dust, possibly
resulting in excessive heat or fire.
• Remove the electric plug from the outlet
when the device is not to be used for
extended periods of time, or during
electrical storms.
• Be sure to connect to an appropriate
outlet with a protective grounding
connection.
• If you plan to connect a powered device
that complies with the IEEE802.3at
standards, use a CAT5e or higher-grade
cable. Failure to observe this precaution
could result in a fire or malfunction.
English
PRECAUTIONS
SWR2100P-10G/SWR2100P-5G Owner’s Manual 5
Do not open
• This device contains no user-serviceable
parts. Do not open the device or attempt
to disassemble the internal parts or
modify them in any way. If it should
appear to be malfunctioning, discontinue
use immediately and have it inspected by
qualified Yamaha service personnel.
Water warning
• Do not expose the device to rain, use it
near water or in damp or wet conditions,
or place on it any containers (such as
vases, bottles or glasses) containing
liquids which might spill into any
openings. If any liquid such as water
seeps into the device, unplug the power
cord from the AC outlet. Then have the
device inspected by qualified Yamaha
service personnel.
• Never insert or remove an electric plug
with wet hands.
Hearing loss
• When turning on the AC power in your
audio system, always turn on the power
amplifier LAST, to avoid hearing loss and
speaker damage. When turning the
power off, the power amplifier should be
turned off FIRST for the same reason.
Fire warning
• Do not place any burning items or open
flames near the device, since they may
cause a fire.
If you notice any abnormality
• If any of the following problems occur,
disconnect the electric plug from the
outlet.
- The power cord or plug becomes frayed
or damaged.
- Unusual smells or smoke are emitted.
- Some object has been dropped into the
device.
- Cracks or other visible damage appear
on the device.
Then have the device inspected or
repaired by qualified Yamaha service
personnel.
• If this device should be dropped or
damaged, immediately disconnect the
electric plug from the outlet, and have the
device inspected by qualified Yamaha
service personnel.
PRECAUTIONS
6SWR2100P-10G/SWR2100P-5G Owner’s Manual
CAUTION
Always follow the basic precautions
listed below to avoid the possibility of
physical injury to you or others, or
damage to the device or other property.
These precautions include, but are not
limited to, the following:
Power supply/power cord
• When removing the electric plug from the
device or an outlet, always hold the plug
itself and not the cord. Pulling by the cord
can damage it.
Location
• Do not place the device in an unstable
position where it might accidentally fall
over and cause injuries.
• Do not block the vents. This device has
ventilation holes at the top to prevent the
internal temperature from becoming too
high. In particular, do not place the
device on its side or upside down.
Inadequate ventilation can result in
overheating, possibly causing damage to
the device(s), or even fire.
• When installing the device:
- Do not cover it with any cloth.
- Do not install it on a carpet or rug.
- Make sure the top surface faces up; do
not install on its sides or upside down.
- Do not use the device in a confined,
poorly-ventilated location.
Inadequate ventilation can result in
overheating, possibly causing damage to
the device(s), or even fire. If this device is
to be used in a small space other than an
EIA-standard rack, make sure that there is
adequate space around the device: at
least 1.3 cm above.
• Do not place the device in a location
where it may come into contact with
corrosive gases or salt air. Doing so may
result in malfunction.
• Before moving the device, remove all
connected cables.
• If the device is mounted in an EIA
standard rack, carefully read the section
“Attaching the rack mount” on page 17.
Inadequate ventilation can result in
overheating, possibly causing damage to
the device(s), malfunction, or even fire.
Maintenance
• Remove the power plug from the AC
outlet when cleaning the device.
Handling caution
• Avoid inserting or dropping foreign
objects (paper, plastic, metal, etc.) into
any gaps or openings on the device
(vents, panel, etc.) If this happens, have
the device inspected by qualified Yamaha
service personnel.
• Do not rest your weight on the device or
place heavy objects on it. Avoid applying
excessive force to the buttons, switches
or connectors to prevent injuries.
• Avoid pulling the connected cables to
prevent injuries or damage to the device.
Yamaha cannot be held responsible for
damage caused by improper use or
modifications to the device.
English
NOTICE
SWR2100P-10G/SWR2100P-5G Owner’s Manual 7
NOTICE
To avoid the possibility of malfunction/
damage to the product, damage to data, or
damage to other property, follow the notices
below.
Handling and maintenance
• Do not touch any port with your fingers or
anything metallic. Failure to observe this
precaution could result in damage to the
product.
• Do not use the device in the vicinity of a
TV, radio, AV equipment, mobile phone, or
other electric devices. Otherwise, the
device, TV, or radio may generate noise.
• Do not expose the device to excessive
dust or vibration, or extreme cold or heat
(such as in direct sunlight, near a heater,
or in a car during the day), in order to
prevent the possibility of panel
disfiguration, unstable operation, or
damage to the internal components.
• Do not place vinyl, plastic or rubber
objects on the device, since this might
discolor the panel.
• When cleaning the device, use a dry and
soft cloth. Do not use paint thinners,
solvents, cleaning fluids, or chemical-
impregnated wiping cloths.
• Condensation can occur in the device due
to rapid, drastic changes in ambient
temperature—when the device is moved
from one location to another, or air
conditioning is turned on or off, for
example. Using the device while
condensation is present can cause
damage. If there is reason to believe that
condensation might have occurred, leave
the device for several hours without
turning on the power until the
condensation has completely dried out.
• Be sure to earth (ground) any static
electricity from your body or clothing
before touching the product. Failure to
observe this precaution could result in
damage to the product.
• Do not install the product in a location
where magnetic fields are strong.
Otherwise, it might cause the product to
malfunction.
• Do not connect any noise generating
devices on the same power line as the
product. Failure to observe this precaution
could result in a malfunction or damage to
the product.
• Do not locate any connected LAN cables
close to the power cord. Otherwise, high
voltage might be induced, resulting in
malfunction.
• A 1000BASE-T connection will require an
Enhanced Category 5 (CAT5e) or better
LAN cable.
• The rubber feet included in this package
can be attached to the device to prevent
slippage when it is to be used on a
slippery surface.
About functions/data bundled with the
device
• This is a class A product. In a domestic
environment this product may cause radio
interference in which case the user may
be required to take adequate measures.
(CISPR22)
Regarding disposal
• This product contains recyclable
components.
When disposing of this product, please
contact the appropriate local authorities.
NOTICE
8SWR2100P-10G/SWR2100P-5G Owner’s Manual
About this manual
• The illustrations as shown in this manual
are for instructional purposes only.
• The company names and product names
in this manual are the trademarks or
registered trademarks of their respective
companies.
• Software may be revised and updated
without prior notice.
Open Source Software Used in this
Product
• Please refer to Yamaha Pro Audio website
for the details of licensing article.
http://www.yamaha.com/proaudio/
• Suitable for installation in Information Technology Rooms in accordance with Article 645 of
the National Electrical Code and NFPA 75.
• The device can only be used in a fixed location such as a telecommunication centre, a
dedicated computer room. When you install the device, ensure that the protective earthing
connection of the socket-outlet is verified by a skilled person.
European models
Purchaser/User Information specified in EN55103-2:2009.
Conforms to Environments: E1, E2, E3 and E4
The model number, serial number, power requirements, etc., may be
found on or near the name plate, which is at the top of the unit. You
should note this serial number in the space provided below and retain
this manual as a permanent record of your purchase to aid identifica-
tion in the event of theft.
Model No.
Serial No.
(top_en_01)
English
SWR2100P-10G/SWR2100P-5G Owner’s Manual 9
Table of contents
PRECAUTIONS ......................................................................................................... 4
NOTICE ..................................................................................................................... 7
Introduction.............................................................................................................10
Features...................................................................................................................10
Accessories .............................................................................................................10
Options ....................................................................................................................10
Related application software....................................................................................10
Controls and Connectors.......................................................................................11
Front panel...............................................................................................................11
Top panel .................................................................................................................13
Rear panel ...............................................................................................................14
Bottom panel............................................................................................................15
Setting the CONFIGURATION switches ................................................................16
Attaching the rack mount.......................................................................................17
Connections ............................................................................................................19
Appendix................................................................................................................. 20
Hardware specifications.......................................................................................... 20
Dimensions............................................................................................................. 21
Software license agreement ................................................................................... 22
Particular usage in this manual
The following company and product names will be abbreviated as below in this manual.
• Yamaha L2 Switch SWR2100P-10G/SWR2100P-5G: This product
• 10BASE-T/100BASE-TX/1000BASE-T cable: LAN cable
10 SWR2100P-10G/SWR2100P-5G Owner’s Manual
Introduction
Thank you for purchasing the Yamaha SWR2100P-10G or SWR2100P-5G, an L2 switch.
This product supplies power to PoE powered devices on the network.
This owner’s manual explains how to install and set up the unit. It is intended for installers or
facility designers.
Please be sure to read this manual before you start using the product to take full advantage of
its features.
Please retain this manual in a safe location for future reference.
• The fanless design promotes extremely quiet operation.
• The unit can be mounted in a 19-inch rack.
• By linking the unit to the Yamaha LAN Monitor software application, you can obtain
information about the PoE power supply status and the amount of power supplied. You can
also stop or resume the power supply by using the software.
Please ensure that you have all of the following accessories.
• Owner’s Manual (this manual)
•Power Cord
• Power Cord Clamp (used only for the included dedicated power cord)
• Rubber feet (x4)
• RK-SWR Rack-mount accessory
Use this rack-mount accessory to mount the unit in a 19-inch rack. Refer to “Attaching the
rack mount” (page 17) for information on how to install the unit.
• Yamaha LAN Monitor
This application software enables you to obtain information about the SWR2100P-10G/
SWR2100P-5G and to monitor an entire network, including all Dante devices on the
network.
Download this application from the following website:
http://www.yamaha.com/proaudio/
Features
Accessories
Options
Related application software
English
SWR2100P-10G/SWR2100P-5G Owner’s Manual 11
Controls and Connectors
■SWR2100P-10G
■SWR2100P-5G
1POWER indicator
Lights up when power is provided to the unit.
2PoE LIMIT indicator
Indicates the status of maximum power supply.
Front panel
POWER indicator Power
Light off OFF
Light on (green) ON
PoE LIMIT indicator Maximum power supply
Light off Lower than 63 W
Light on (green) 63 W or higher, lower than 70 W
Flashing (green) 70 W or higher
31
24 675
13
24 6 75
12 SWR2100P-10G/SWR2100P-5G Owner’s Manual
If the total power supply is 63W or higher but lower than 70W (in this case, the PoE LIMIT
indicator will light up steadily in green), you will be unable to increase the number of
powered devices to which power is supplied. Therefore, if you connect a powered device
to a higher-priority port on the unit, power will be supplied to that powered device, but will
not be supplied to a powered device connected to a lower-priority port. On the other hand,
if you connect a powered device to a lower-priority port on the unit, power will not be
supplied to that powered device.
If the total power supply is 70W or higher (in this case, the PoE LIMIT indicator will flash
green), power will not be supplied to a lower-priority port.
Port 1 has the highest priority. Priority decreases as the port number increases (1
2
3 ...).
Power consumption on certain powered devices varies between standby mode and
operating mode. Check the owner’s manual for information on the maximum power
consumption of the powered devices to be connected.
3LINK/ACT indicator
Indicates LAN port status.
The loop detection function can be turned ON/OFF using CONFIGURATION switch 4 on
the front panel of the main unit. When turned ON, the loop detection function is enabled in
all ports, and in the event of loop detection, communication from the corresponding port is
automatically blocked. When turned OFF, the loop detection and blocking functions are
disabled in all ports.
4SPEED indicator
Indicates the connection speed of the LAN port.
5PoE STATE indicator
Indicates the power supply status.
*1 The indicator is also turned off if a device is not connected to the corresponding port; if the
connected device does not need a power supply; or if power is not being supplied to the device
due to a limitation in the unit’s total power supply.
*2 The indicator will flash green if power supply is suspended because the power output at the port
has exceeded the maximum power supply allowed per port. The maximum power supply allowed
per port varies depending on the power consumption class of the connected powered device.
LINK/ACT indicator LAN port status
Light off Link down. (unavailable)
Light on (green) Link established. (available)
Flashing (green) Data is being transferred.
Flashing (orange) Loop detected.
SPEED indicator Connection status
Light off Not connected or connecting via 10BASE-T.
Light on (orange) Connecting via 100BASE-TX.
Light on (green) Connecting via 1000BASE-T.
PoE STATE indicator Power supply status
Light off Not supplying *1
Light on (green) Supplying
Flashing (green) Not supplying *2
English
SWR2100P-10G/SWR2100P-5G Owner’s Manual 13
6LAN ports
These are ports for 10BASE-T, 100BASE-TX, and 1000BASE-T. Port #10 on the
SWR2100P-10G and port #5 on the SWR2100P-5G are uplink ports, and do not provide a
power supply function.
7CONFIGURATION switch
Sets enabling/disabling of functions.
Please refer to “Setting the CONFIGURATION switches” (page 16).
8Product label
Indicates the equipment name, serial number, MAC address, etc. of the unit.
Top panel
8
Serial number
MAC address
14 SWR2100P-10G/SWR2100P-5G Owner’s Manual
9Holes for attaching the power cord clamp
Attach the included power cord clamp (U-shaped type). For information about the
attachment method, please refer to “Connections” (page 19).
0Power inlet (3 poles connector, C14-type)
Insert the included power cord. Connect to outlets between AC 100V and AC 240V
(50/60 Hz).
Rear panel
9
0
Serial number
English
SWR2100P-10G/SWR2100P-5G Owner’s Manual 15
ARubber feet installation guide
The following figure shows the position of the included feet when the unit is placed
horizontally upside-down.
When placing the unit horizontally, please attach the included feet as indicated in the
figure.
BAttachment holes for the rack-mount accessory
Use these holes to attach the RK-SWR rack-mount accessory. Refer to “Attaching the
rack mount” (page 17) for information on how to install the unit.
Bottom panel
A
B
A
Feet
Rubber feet
Rubber feet installation
16 SWR2100P-10G/SWR2100P-5G Owner’s Manual
Setting the CONFIGURATION switches
You can enable or disable functions for
this unit by setting the CONFIGURATION
switches.
In order to operate the switches, please
use something round, such as the tip of a
ballpoint pen or small screwdriver. This
unit reads the switch status at startup and
enables or disables functions as
indicated. If the switch status is changed
after startup, the new switch status will be
in effect at the next startup.
The functions which can be set via the CONFIGURATION switches are as follows.
* This is the factory default setting.
■L2MS (Layer 2 Management Service) function
This function manages Yamaha network devices, including this unit, at the layer 2 level.
You can control the unit from a Yamaha LAN Monitor that features the L2MS controller
function.
■Low power consumption mode
The lower power consumption mode of this unit is compatible with the following methods
of IEEE802.3az Energy Efficient Ethernet (called “EEE” in this manual).
• 10BASE-Te
• 100BASE-TX/1000BASE-T (LPI)
NOTE
Do not use the EEE function (*) on the network switch within the Dante network.
Between switches that feature the EEE function, the setting for power consumption is
automatically adjusted. However, some switches might not respond correctly to this
adjustment. Therefore, the EEE function on some switches might be enabled accidentally
within the Dante network, which might cause clock sync performance to deteriorate and result
in audio that breaks up.
* EEE (Energy Efficient Ethernet) function is used to reduce power consumption of Ethernet devices when
network traffic is low. This technology is also called “Green Ethernet” or “IEE802.3az”.
CONFIGURATION
switches
No. Setting function OFF ON
1 L2MS (Layer 2 Management Service) function Disabled Enabled*
2 Flow control Disabled Enabled*
3 Auto MDI/MDI-X Disabled Enabled*
4 Loop detection function Disabled* Enabled
5 Low power consumption mode Disabled* Enabled
English
SWR2100P-10G/SWR2100P-5G Owner’s Manual 17
Attaching the rack mount
This section explains how to attach an optional RK-SWR rack mount accessory to the unit.
Please read before mounting the unit into a rack
This unit is guaranteed to operate properly at 0–40 degree Celsius (32–104 degrees
Fahrenheit). If you install this unit along with other devices into an EIA-standard rack, the
temperature inside the rack may rise due to heat released from the other devices, resulting
in poor performance of the unit. To prevent the temperature inside the rack from rising,
mount the unit in the rack, adhering to the requirements below:
• If you plan to rack-mount the unit along with a device that tends to generate heat,
such as an amplifier (excluding an XMV series), be sure to leave a gap of 1U or
more from such devices. Also, be sure to maintain sufficient ventilation in this space
by installing a ventilation panel or leaving it open.
• Open the rear panel of the rack, place the rack 10 cm (about four inches) away from
the walls and ceiling to keep sufficient ventilation. If you cannot open the rear panel of
the rack, install a commercially-available forced ventilation device, such as a fan kit. If
you install a fan kit, closing the rear panel may work better for heat dissipation
purposes. For more information, refer to the owner’s manual for the rack and/or fan kit.
If you plan to relocate the unit, be sure to first remove it from the rack. Moving the unit
along with the rack could cause the unit to malfunction.
Caution
If you plan to relocate the rack, be sure to first remove this unit from the rack.
If you move the rack with this unit mounted, vibration or physical shock might cause the rack
mount accessory to deform or break, possibly causing injury.
There is also a possibility that this unit might malfunction.
[Installation]
This section explains how to attach the unit in the middle block of a rack mount panel.
Even if you plan to attach the unit in the left or right block, follow the procedure below.
Notice
If the supplied feet have already been attached to the unit, remove them.
1. Attaching the rack mount
panel to the unit
Use two screws (supplied with
the rack-mount accessory) to
attach and secure the rack
mount panel to the bottom of
the unit.
Rack mount panel Screws
18 SWR2100P-10G/SWR2100P-5G Owner’s Manual
2. Installing the rack mount panel to the 19-inch rack
Use four screws (supplied with an EIA-standard 19-inch rack) to mount the unit into the
rack. Be sure to tighten the screws so that they will not get loosened.
You can also mount two units as shown in the figure below.
19-inch rack
Rack mount panel
<EIA-standard rack>
Screws supplied
with the 19-inch
rack
English
SWR2100P-10G/SWR2100P-5G Owner’s Manual 19
Connections
1. Connect the LAN port of the network device to the LAN port of this product
using a LAN cable.
2. Connect the power cord to a power inlet.
Notice
• We recommend that you attach the supplied power cord clamp to prevent the
power cord from accidentally being disconnected.
• This clamp is used only for the supplied power cord.
If you use the clamp for other power cords, they might be damaged or might not
secure properly.
3. Connect the power plug to an electrical outlet.
The POWER indicator lights up.
4. Turn the power of the network devices connected to this product ON.
If the LINK/ACT indicator corresponding to the LAN port to which the network device is
connected turns green or flashes green, this indicates that the status is normal.
[If the LINK/ACT indicator corresponding to the LAN port does not turn green or
flash green]
Please check that the LAN cable is correctly connected and the power of the
connected network device is ON.
[If the LINK/ACT indicator corresponding to the LAN port flashes orange]
Loop detected. Please check the LAN cable connection.
1342
Insert the included
clamp into the holes of
the main unit.
Raise the clamp. Plug in the
power cord. Affix the power
cord in place by
pressing down on
the clamp.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
Yamaha SWR2100P-10G Le manuel du propriétaire
- Catégorie
- Équipement musical supplémentaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Yamaha SWR2100P-10G Owner's manual
Documents connexes
-
Yamaha SWR2100P-10G Le manuel du propriétaire
-
-
-
-
-
-
-