Insignia Magnetic Charging Cable Mode d'emploi

Taper
Mode d'emploi

Ce manuel convient également à

PACKAGE CONTENTS
Magnetic charging cable
• Cable management bumper
Quick Setup Guide
COMPATIBILITY
Apple® Watch Series 1, 2, 3, 4, and 5
FEATURES
The silicone cable management bumper
stays in place even if it is bumped.
Note: Your magnetic charging cable is slightly
larger than the original Apple® Charging Cable
and may not t in all charging stands designed
for an Apple® Watch magnetic charging cable.
QUICK SETUP GUIDE
Magnetic
Charging Cable
NS-AWCB4CM / NS-AWCB4CM-C
WRAPPING THE CABLE
1 Wind the cord around the cable management bumper until the end with the USB
connector is sticking out about an inch.
Note: Make sure that you wrap it tightly.
Before using your new product, please read
these instructions to prevent any damage.
2 Flip the cable management bumper
over and insert the USB connector into
the notch in the back of the bumper.
Cable management
bumper
Magnetic
charger
Top view
USB connector
Back view
Side view
Notch
USB connector
USING YOUR MAGNETIC
CHARGING CABLE
1 Pull out the USB connector from the
back of the cable management
bumper and unwind the cord.
2 Plug the USB connector into your
charging source (not included), then set
your Apple watch on top of the charger.
SPECIFICATIONS
Dimensions (H × D):
0.75 in. × 2.75 in. (19 mm × 70 mm)
• Cable length: 4 ft. (121.9 cm)
V2 ENGLISH 210318
LEGAL NOTICES
This device complies with Part 18 of the FCC Rules.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 18 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit dierent from that to
which the receiver is connected. 
This device complies with Part 18 of the FCC Rules. Operation is subject to
the following two conditions:
1) this device may not cause harmful interference and
2) this device must accept any interference received, including interference
that may cause undesired operation of the device. 
Any changes or modications in construction of this device which are not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment 
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
ONE-YEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
1-877-467-4289 (U.S. and Canada)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies.
Distributed by Best Buy Purchasing, LLC.
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2021 Best Buy. All rights reserved.
  • Page 1 1
  • Page 2 2

Insignia Magnetic Charging Cable Mode d'emploi

Taper
Mode d'emploi
Ce manuel convient également à

dans d''autres langues