Eufy AK-T2190121 Manuel utilisateur

Marque: Eufy

Modèle: AK-T2190121

Taper: Manuel utilisateur

Ce manuel convient également à

RoboVac L70 Hybrid Robot Vacuum Cleaner

T2190 51005001609 V02

Owner’s Manual

RoboVac L70 Hybrid

Thank you for purchasing RoboVac. Carefully read all instructions before

using this product, and keep this manual for future reference.

Table of Contents

02 Important Safety Instructions

06 About Your RoboVac

What's in the Box

RoboVac Anatomy

LED Indication

Map Navigation and Management

14 Get Started

Important Tips Before Use

Preparation

Charge Your RoboVac

18 Using Your RoboVac

Turn on / o

Start cleaning

Use Your RoboVac with the EufyHome App

Select a Cleaning Mode

Use Mopping System

Use Your RoboVac with Amazon Alexa / the Google Assistant

Set Up Physical / Virtual Barriers

Reset the System

28 Cleaning and Maintenance

Clean the Dust Collector and Water Tank

Clean the Rolling Brush

Clean the Side Brush

Replace the Side Brush

Clean the Sensors and Charging Pins

Clean the Swivel Wheel

Clean the mopping module

36 Troubleshooting

Voice Alert

Wi-Fi Connection

42 Speciﬁcations

43 Consignes importantes de sécurité

48 Customer Service

02 03

Important Safety Instructions

To reduce the risk of injury or damage, read these safety

instructions carefully and keep them at hand when setting up,

using, and maintaining this device.

WARNING SYMBOLS USED

This is the safety alert symbol. This symbol alerts

you to potential hazards that could result in property

damage and/or serious bodily harm or death.

• This device can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of this

device in a safe way and understand the hazards involved.

• Children should be supervised to ensure they do not play

with this device.

• Cleaning and maintenance shall not be performed by

children without adult supervision.

• This device is only to be used with the power supply unit

provided.

• Before cleaning or maintaining this device, the plug must be

removed from the socket-outlet.

• The battery in this device should only be replaced by a

skilled professional.

• When removing the battery, disconnect the device from the

supply mains.

• For the purposes of recharging the battery, only use the

detachable power supply unit provided with this device.

• The battery must be removed before this device is disposed

of. To remove the battery, first unscrew the screws on the

bottom, then remove the back cover. Remove the battery by

disconnecting the quick connector.

• The used battery should be placed in a sealed plastic bag and

disposed of safely according to local environmental regulations.

• The external flexible cable or cord of the power supply unit

cannot be replaced; if the cord is damaged, the power supply

unit shall be disposed of.

• This device is for indoor use only.

• This device is not a toy. Do not sit or stand on this device.

Small children and pets should be supervised when this

device is operating.

• Store and operate this device in room temperature

environments only.

• Clean with a cloth dampened with water only.

• Do not use this device to pick up anything that is burning or

smoking.

• Do not use this device to clean up spills of bleach, paint,

chemicals, or anything wet.

• Before using this device, pick up objects like clothing and

loose paper. Lift up cords for blinds or curtains, and move

power cords and fragile objects out of the way. If this device

passes over a power cord and drags it, an object could be

pulled off a table or shelf.

• If the room to be cleaned has a balcony, a physical barrier

should be used to prevent access to the balcony and to

ensure safe operation.

• Do not place anything on top of this device.

• Be aware that this device moves around on its own. Take

care when walking in the area where this device is operating

to avoid stepping on it.

• Do not operate this device in areas with exposed electrical

outlets on the floor.

• Do not expose the electronics of this device, its battery, or

the integrated Charging Base. There are no user-serviceable

parts inside.

04 05

• Do not use this device on an unfinished, unsealed, waxed

or rough floor. It may result in damage to the floor and this

device. Use only on hard floor surfaces or low-pile carpet.

• Do not use the mopping module on carpets.

• This device has been designed to be used on floors without

scratching them. We still recommend that you test this

device on a small area of the room to be cleaned to ensure

no scratches are made before cleaning the whole room.

• Only use attachments recommended or described in this

manual.

• Do not handle the appliance or plug with wet hands.

• Ensure that the dust bag and/or filters are correctly in-place

before usage.

• Do not use a battery pack or appliance that is damaged

or modified. Damaged or modified batteries may exhibit

unpredictable behavior resulting in fire, explosion or risk of

injury.

• Do not expose the battery pack or appliance to fire or

excessive temperature. Exposure to fire or temperature

above 130°C may cause explosion.

• Do not modify or attempt to repair the appliance or the

battery pack (as applicable), except as indicated in the

instructions for use and care.

• Follow all charging instructions and do not charge the

battery pack or appliance outside of the temperature range

specified in the instructions. Charging improperly or at

temperatures outside of the specified range may damage the

battery and increase the risk of fire.

• The laser distance sensor of this device meets the standards

for Class I Laser Products in IEC 60825-1:2014 and will not

generate hazardous laser radiation.

Notice

This symbol on the device or its packaging indicates:

Do not dispose of electrical appliances as unsorted

municipal waste; use separate collection facilities.

Contact your local authority for information regarding

the collection systems available. If electrical appliances

are disposed of in landfills or dumps, hazardous

substances can leak into the groundwater and get into

the food chain, damaging your health and well-being.

When replacing old appliances with new ones, the

retailer is legally obliged to take back your old appliance

for disposal at least free of charge.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following

measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation

between the equipment and receiver. (3) Connect the equipment into an outlet on a

circuit different from that to which the receiver is connected. (4) Consult the dealer or an

experienced radio / TV technician for help.

The FCC 15.19 statement can be found on the back of the top panel.

RF Exposure Compliance Statement

This equipment complies with FCC/IC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with minimum

distance 20cm between the radiator and your body.

ISED Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with

Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause

undesired operation of the device.

06 07

Declaration of Conformity

This product complies with the radio interference requirements of the European

Community. Hereby, Anker Innovations Limited declares that the radio equipment type

T2190 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of

conformity is available at the following internet address: https://www.eufylife.com/.

Maximum output power: 18 dBm (For EU)

Frequency band: 2.4G band (2.4000GHz - 2.4835GHz)

Trademark Notice

• Amazon, Echo, Alexa and all related logos are trademarks of Amazon.com, Inc. or its

affiliates.

• Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other

countries. App Store is a service mark of Apple Inc., registered in the U.S. and other

countries.

• Google Play and the Google Play logo are trademarks of Google Inc.

• Google Home is a trademark of Google Inc.

About Your RoboVac

What's in the Box

Waterproof Pad Owner’s Manual &

Other Documents

Power Adapter

RoboVac

Mopping Module

(with Washable Mopping Cloth)

Charging Base

RoboVac Anatomy

A. Top

Press and hold for 3 seconds to

Press to start Auto cleaning

Press to pause the current task when working

Press to return RoboVac to the Charging Base;

press again to pause

Press and hold for 3 seconds to start Spot

cleaning

Press and hold both buttons for 3 seconds to

reset Wi-Fi connection

Laser distance sensor (LDS)

Wi-Fi status light

Top Panel

turn on or o (when not in Charging status)

LDS cover (with bumper sensor)

System reset button

Laser distance sensor (LDS)

Dust collector & water tank

Release button

Dust collector & water tank

Water pump component

08 09

B. Dust collector & Water tank

Cleaning brush

Filter

Dust disposal outlet

Water inlet cover

Water inlet

Button for separating dust collector & water tank

Buckles

Water pump connector

Pre-ﬁlter

Foam ﬁlter

High-performance

ﬁlter

C. Side

Ventilation holes

Wall sensor

Front infrared sensor

Bumper

D. Bottom

Side brush

Wheels

Brush guard

Rolling brush

Charging contact pins

Swivel wheel

Drop Sensors

Water outlets

10 11

E. Mopping module

Water outlets

Buckles

Release buttons

Cloth attachment area

Washable mopping cloth

Slot

F. Charging Base

External view

Status light

Charging contact pins

Internal view

Cover

Power cable

Slot winding

Power socket

Wire slot exit

Power cord storage compartment

G. Suction Inlet

Suction inlet

12 13

LED Indication

You can see the status of RoboVac from the LED indicators.

(Power Status Lights)

Status

Solid blue

• Standby / Cleaning (when not on Charging Base)

• Fully charged

Solid purple • Low power and returning to Charging Base

Breathing blue

• Charging (power level ≥ 20%)

• Loading system

Breathing purple • Charging (power level < 20%)

Flashes blue 3 times

• Status indication (along with voice prompts)

Flashing red

• Error indication (along with voice prompts)

Refer to the “Troubleshooting>Voice Alert” section in this

manual for solutions.

When RoboVac is inactive and not on the Charging Base for 10 minutes, it

automatically switches to sleep mode and the light becomes dim to conserve

power.

(Wi-Fi Status Light)

Status

Slowly flashing blue

Waiting for connection (RoboVac cannot connect to Wi-Fi

network in sleep mode)

Rapidly flashing blue Connecting with your wireless router

Solid blue Connected to your wireless router

Map Navigation and Management

Navigation

Once Auto cleaning starts, RoboVac moves from the Charging Base, automatically scans to

generate maps, intelligently determines its cleaning route, and divides the space into zones.

The cleaning paths are planned along the walls, following a bow-shaped cleaning method

to complete the cleaning of each zone one by one.

Real-time Mapping & Floor plan

Real-time mapping helps you know the cleaning path and environment easily. A floor plan

will be built after cleaning. The map will be updated real-time during each cleaning to

ensure normal navigation.

To create a complete floor plan:

1. open your doors for RoboVac to map each room;

2. remove any objects that may be in the way or get RoboVac stuck.

Do not remove the Charging Base after a floor plan is created.

Relocalization & Remapping

If the position of RoboVac / Charging Base is adjusted or the surroundings are changed

significantly, RoboVac will try to relocalize and may remap to match the surroundings.

• RoboVac will resume cleaning if the relocalization is successful.

• If the relocalization fails, RoboVac will remap to ensure normal navigation with a new

cleaning.

14 15

• If the original map has the virtual boundary information, RoboVac will not start a new

cleaning to avoid going across the restricted zone.

• Make sure RoboVac starts each cleaning from the Charging Base.

• During cleaning, do not move the device frequently. If moved, place RoboVac

back to the original position.

Get Started

Important Tips Before Use

Remove power cords and small objects from the floor that may entangle RoboVac.

Fold tasseled edges of area rugs underneath to prevent tangling RoboVac. Avoid

cleaning very dark-colored high-pile rugs or rugs thicker than 1.02 in/26 mm as they

may cause RoboVac to malfunction.

Keep RoboVac away from spaces lower than 4.17 in/106 mm to prevent RoboVac from

getting stuck. If necessary, place a physical barrier to block off the problem areas.

Keep RoboVac away from wet areas during cleaning.

RoboVac may climb on top of objects less than 0.67 in/17 mm in height (the height will

be reduced if the mopping module is installed). Remove these objects if possible.

Anti-drop sensors will prevent RoboVac from tumbling down stairs and steep drops in

most cases. Sensors are less effective if dirty or used on carpeted/reflective/very dark-

colored floors. It is recommended to place physical barriers to block off areas where

RoboVac may fall.

Place physical barriers in front of fireplaces and areas that may cause damage to

RoboVac if entered.

Preparation

1. Remove the foam blocks beside the bumper before use.

2. Connect the adapter to the Charging Base and put extra cable in the slot as illustrated.

Extra power cord on the ground may be pulled by the main unit to cause an

interruption of charging.

3. Place the Charging Base on a level surface and against a wall.

4. Remove objects within 1.6 ft/0.5 m of the left and right side and within 4.9 ft/1.5 m

of the front of the Charging Base. If you cannot remove the objects, check whether

RoboVac can return to the Charging Base normally; if not, contact eufy customer service

for help.

16 17

5. Insert the Charging Base into the waterproof pad to keep the floor dry. Make sure it is

firmly installed. If mopping is not needed, you can skip this step.

6. Connect the adapter to a wall outlet.

LED Indicator on

Charging Base

Status

Solid white

Charging Base connected to power source (When RoboVac is not

docked)

Off RoboVac properly connected to Charging Base

- Install the Charging Base in a location that RoboVac can easily access. It is

recommended to place the Charging Base against a wall, and on a hard-level

surface rather than on rugs or carpets.

- Always keep the Charging Base plugged in, otherwise RoboVac will not

automatically return to it.

- To ensure proper charging, do not frequently move the Charging Base. When

its location is changed, RoboVac may remap due to failure in relocalization

(see About Your RoboVac > Map Navigation and Management for details).

Charge Your RoboVac

• RoboVac has a pre-installed rechargeable battery that has to be fully charged before use.

• RoboVac will return to the Charging Base at the end of a cleaning cycle or when its

battery is running low.

Method 1: Attach RoboVac to the Charging Base by aligning its charging pins with the

charging pins on the base.

Method 2: Press on the main unit to send RoboVac to the Charging Base.

- To preserve the battery’s lifespan, recharge at least once every 6 months.

- To enter Reduced Power Standby mode when RoboVac is being charged, press

and hold

& simultaneously on RoboVac for 20 seconds until the Power

Status Lights turn off. Wi-Fi is disabled while this mode is active. Press to

exit Reduced Power Standby mode.

18 19

Auto Recharge and Resume

RoboVac returns to the Charging Base automatically to recharge when:

• RoboVac has finished cleaning;

• Cleaning is not complete and the battery level becomes low; Once recharged to 80%

battery capacity, RoboVac will resume to finish the remaining cleaning.

- Do not move the Charging Base during cleaning, otherwise RoboVac may fail

to return for recharge. If failed, you have to manually attach it to the Charging

Base.

Using Your RoboVac

Turn on / off

• RoboVac turns on automatically when attached to the Charging Base and connected to

power.

• When RoboVac is not on the Charging Base, press and hold for 3 seconds to turn on

the main unit. Wait until the Power Status Light turns solid blue.

• When RoboVac is not on the Charging Base, press and hold for 3 seconds again to

turn off the main unit.

Switch to Sleep Mode

• When inactive and not on the Charging Base for 10 minutes, RoboVac automatically stops

cleaning and switches to sleep mode. In sleep mode, press any button to wake it up.

Start cleaning

RoboVac cannot start cleaning if the battery level is less than 20%. In this case,

recharge RoboVac first before cleaning.

1. Press to start cleaning in Auto Mode.

RoboVac moves around to scan the environment and build the map automatically.

2. Press again to pause cleaning.

Press to resume cleaning.

When cleaning is paused, docking the main unit onto the Charging Base will stop the

cleaning.

If cleaning is paused for 10 minutes, RoboVac automatically stops cleaning and

switches to sleep mode.

3. Press to stop current cleaning and return to the Charging Base.

• Before cleaning, sort out cables and cords to avoid power interruption or any

damaging caused by pulling the cord during cleaning.

• In Auto cleaning mode, RoboVac will clean twice by default if the cleaning

time is less than 10 minutes.

Use Your RoboVac with the EufyHome App

To fully enjoy all the available features, it is recommended to control your RoboVac via the

EufyHome app.

Before you start, make sure that:

• Your smartphone or tablet is connected to a Wi-Fi network.

• Your smartphone or tablet is running iOS 8.0 (or above) or Android 4.4 (or above).

• The 2.4GHz band wireless signal is enabled on your wireless router.

20 21

• The Wi-Fi status light on RoboVac is slowly flashing blue.

• RoboVac is attached to the Charging Base to ensure it has enough power during setup.

EufyHome

1. Download the EufyHome app from the App Store (iOS devices) or Google Play (Android

devices).

2. Open the app and create a user account.

3. Tap the “+” icon to add RoboVac to your EufyHome account.

4. Follow the instructions in the app to set up the Wi-Fi connection.

After connecting successfully, you can control RoboVac via the app.

With the app, you can select cleaning at your desired suction level, schedule cleaning,

view the cleaning map, set up “No-Mop” or “No-Go” zones, check the network

connection status, and access additional features.

Wi-Fi Status Light

Slowly flashing blue Waiting for connection

Rapidly flashing blue Connecting with your wireless router

Solid blue Connected with your wireless router

• If you have any problems during the Wi-Fi setup process, refer to the

“Troubleshooting > Wi-Fi connection” section in this Manual.

• If RoboVac gets stuck in any space, tap Find My Robot in the app to find the

machine. This function is available in the app only.

Reset the Wi-Fi Connection

Press and hold and simultaneously for 3 seconds to reset the Wi-Fi connection if

necessary.

You will hear a voice prompt when the Wi-Fi connection has been reset, and the Wi-Fi

status light will slowly flash blue. Now you can follow the Wi-Fi instructions in the

eufyHome app to set up the Wi-Fi connection.

Schedule Cleaning

With the EufyHome app, you can schedule RoboVac to start cleaning at a particular time.

• You can set the time and customize the cleaning schedules from Sunday to

Saturday on the EufyHome app. This function is available in the app only.

Select a Cleaning Mode

• You can press at any time to pause the current cleaning cycle.

1. Auto cleaning

1. Press to start cleaning in Auto Mode.

2. Press again to pause cleaning.

- By default, RoboVac starts in Auto cleaning mode when it is turned on.

22 23

2. Spot cleaning

RoboVac intensively cleans a specific area with a size of 4.9 ft x 4.9 ft / 1.5 m x 1.5 m.

Useful if there is a concentrated area of dust or debris. When the cleaning of a certain zone

is finished, it automatically returns to the Charging Base.

4.9ft/1.5m

• Press and hold for 3 seconds to start Spot cleaning.

3. Zone cleaning (available via the app only)

In this mode, set up a cleaning zone in the EufyHome app. RoboVac will clean this zone

only and return to the Charging Base after cleaning.

• Start Zone cleaning only after RoboVac has created the map.

• It is recommended that RoboVac moves from the Charging Base to start Zone

cleaning.

4. Manual-controlled cleaning (available via the app only)

You can direct RoboVac to clean a particular area by using manual controls in the

EufyHome app.

5. Select a Suction Power Level

In the EufyHome app, select a suction power level according to your needs:

• Quiet

• Standard (Default)

• Turbo

• Max

• You can select the “Mop-Only” suction level in mopping mode. When

mopping is finished, RoboVac will change to default suction level

automatically.

6. Select BoostIQ™ feature

In the EufyHome app, select the BoostIQ™ feature according to your needs. RoboVac will

automatically increase the suction power if it detects that stronger power is needed to

ensure the best clean. BoostIQ™ is ideal for cleaning thicker carpets and hard-to-sweep

messes, which will reduce the total cleaning time, but increase the noise level. If the

vacuuming noise caused by BoostIQ™ disturbs you, you can disable this feature.

Use Mopping System

• The mopping mode is only intended for a clean floor without stubborn stains

or liquids. To avoid staining floors, do not use the mopping function when dust

is mixed with liquids such as coffee or ink.

• Mopping System cleans best on smooth hard surfaces and may not perform so

well on uneven tiles, heavily waxed floors or rough surfaces like slate or brick,

which may snag the cleaning pad.

• The mopping mode is not recommended when no one is at home.

• Do not use the mopping mode on a carpeted floor. It is recommended to set a

“No-Mop” zone in the EufyHome app to avoid cleaning the carpeted area.

24 25

1. Take out the water tank and put it back into the main unit after filling the water.

- Do not use any other cleaning solution other than water. Cleaning solutions,

even natural ones, can clog the water release system and break down the

materials inside the device.

- To add water into the water tank or install the mopping module, pause the

cleaning first. Do not manually move the device.

2. Wet the mopping cloth and wring it until it does not drip. Insert the cloth along the

bracket slot and stick it firmly.

3. Install the mopping module into the bottom of RoboVac until a click is heard.

When the mopping module is inserted, RoboVac automatically switches to the

mopping mode.

4. Select a cleaning mode to start cleaning.

RoboVac automatically sweeps and mops in the selected mode.

If you want RoboVac to mop without vacuuming, select “Mop-Only” mode in the

EufyHome app.

You can also select the mopping water level (3 levels) in the app according to your

needs.

• To achieve a better mopping effect, it is recommended to clean the floor with

RoboVac three times before installing the mopping module.

5. When RoboVac finishes working and returns to the Charging Base, hold the two buckles

by hand, drag backward and remove the mopping module.

When the mopping module is removed, the system automatically exits mopping

mode without water release.

• Although water release is stopped when cleaning is paused, the mopping cloth

will still be wet. Be careful not to keep RoboVac in one location for too long, as

the excessive moisture caused by the cloth can damage the floor.

• To avoid damaging wooden floors, make sure the Charging Base is attached to

the waterproof pad.

26 27

6. Empty any remaining water from the water tank. Clean the mopping cloth to avoid it

being mildewed and producing unpleasant smell.

24h

• It is recommended to clean the mopping cloth after mopping each time.

• Remove the mopping module when RoboVac is under charging or not in use.

Use Your RoboVac with Amazon Alexa / the Google

Assistant

Amazon Alexa or the Google Assistant is a smart voice control device that enables you to

control RoboVac with your voice.

Before you start, make sure that:

• RoboVac is attached to the Charging Base to ensure there is enough power.

• RoboVac is connected with the EufyHome app.

• You have an Alexa-enabled device (i.e. Amazon Echo, Echo Dot and Amazon Tap, Echo

Show, Echo Spot) or a device enabled with the Google Assistant (i.e. Google Home,

Google Home Mini). These devices are sold separately.

• The Amazon Alexa app or Google Home app is already installed on your smart device,

and you have created an account.

To control RoboVac with Amazon Alexa or the Google

Assistant

1. Open the EufyHome app and tap “Smart integrations” in the top left.

2. Follow the on-screen instructions to complete the setup.

- Currently this feature only supports English, German, French, and Spanish.

You can check regularly if more languages are supported at

https://www.eufylife.com/support/.

Set Up Physical / Virtual Barriers

Boundary Strips (Sold Separately)

Physical barriers including boundary strips can keep RoboVac away from cleaning certain

areas. RoboVac will recognize the barriers and will not cross into the blocked-off area.

1. Identify the area or item you do not want RoboVac to get close to.

2. Place the boundary strips FLAT on the floor or under an area rug.

• Make sure the boundary strips are placed on the same surface plane RoboVac

is used on.

• If the boundary strips are rolled up, remove and then re-apply on the floor with

adhesive tape. Otherwise the boundary strips may not work well.

Virtual Boundary (Available on the App Only)

In the EufyHome app, you can set up a “No-Go Zone” or “No-Mop Zone” as a restricted

area. This eliminates the need to use physical barriers, including Boundary Strips. This

feature is designed for dividing the cleaning zones, not for isolating hazardous areas.

• No-Go Zone: RoboVac will not enter the zone to vacuum or mop.

• No-Mop Zone: RoboVac will not enter the zone to mop, while vacuuming is still allowed.

• To set a virtual boundary, RoboVac must initially perform a cleaning run to

create a floor plan.

• To clean your home with virtual boundary, ensure that RoboVac is on the

Charging Base and that the Base has not been manually moved during

cleaning.

• Although a virtual boundary is set, RoboVac may still enter the restricted zone

due to such reasons as relocalization, wrong positioning or abnormal sensors.

• Moving the device or changing the environment may cause mapping failed

and rebuilt with virtual boundary lost.

28 29

Reset the System

You can reset the system if there is no response when pressing any button on RoboVac.

1. Make sure RoboVac is not on the Charging Base.

2. Use a clip to press the Reset button.

RoboVac will automatically turn off.

3. Dock RoboVac onto the Charging Base or press to turn it on.

The system is reset.

• After resetting the system, RoboVac may lose its map and the original settings

including the virtual boundary.

Cleaning and Maintenance

Before cleaning and maintaining, turn off the device and unplug the adapter.

For optimal performance, follow the instructions below to clean and maintain RoboVac

regularly. The cleaning/replacement frequency will depend on your usage habits of

RoboVac.

Recommended cleaning/replacement frequency

RoboVac Part Cleaning Frequency Replacement Frequency

Dust Collector After each use -

Filter Once every week Every 6 months

Rolling Brush Once every week Every 6-12 months

Side Brush Once every month Every 3-6 months (or when visibly worn)

Brush Guard Once every month Every 3-6 months (or when the silicone

rubber strip on the brush guard becomes

visibly worn)

RoboVac Part Cleaning Frequency Replacement Frequency

Sensors Once every month -

Charging Pins Once every month -

Swivel Wheel Once every month -

Mopping Module After each use -

Mopping Cloth After each use Every 3-6 months (or when visibly worn)

Water Tank After each use -

Clean the Dust Collector and Water Tank

1. Open the top panel of RoboVac and press the release button to remove the dust collector

and water tank.

2. Take out the filter assembly.

3. Take out the pre-filter, foam filter, and high-performance filter.

4. Clean the filters with a vacuum cleaner or a cleaning brush. You can also wash the filters

for deep cleaning.

30 31

5. Empty the dust collector. Tap the dust collector to get rid of any excess dirt.

6. Press the dust collector release button to separate the dust collector from the water tank.

7. Rinse the water tank, dust collector and filter assembly thoroughly with water.

Do not use hot water, or any detergent to clean the filter assembly.

8. Air-dry the water tank, dust collector and filter assembly completely before next use.

24h

9. Replace the pre-filter, foam filter, and high-performance filter.

10. Put the filter assembly back into the dust collector.

11. Reinstall the dust collector with the water tank.

12. Push the assembly back into the main unit.

32 33

Clean the Rolling Brush

1. Pull on the release tabs to unlock the brush guard as shown.

2. Lift the rolling brush to remove.

3. Clean the rolling brush with a cleaning tool or a vacuum cleaner.

4. Reinstall the rolling brush by inserting the fixed protruding end first and then clicking into

place.

5. Press down to snap the brush guard into place.

4 5

2 3

Clean the Side Brush

Foreign substances, such as hair, can easily get tangled in the side brush, and dirt may

adhere to it. Be sure to clean it regularly.

1. Use a Phillips screwdriver to unscrew the screw.

2. Carefully unwind and pull off any hair or string that is wrapped between the main unit

and the side brush.

3. Use a cloth dampened with warm water to remove dust from the brush or to gently

reshape it.

Only use the side brush when it is completely dry.

Replace the Side Brush

The side brushes may become bent or damaged after being used for a period of time.

Follow the instructions below to replace it.

1. Use a Phillips screwdriver to unscrew the screw on the side brush.

2. Pull off the old side brush and snap the new one into place.

3. Screw down the screw to fasten the side brush.

34 35

Clean the Sensors and Charging Pins

To maintain the best performance, clean the drop sensors and charging pins regularly.

• Dust off the sensors and charging contact pins using a cloth or cleaning brush.

Clean the Swivel Wheel

Hair or dust particles can easily get entangled in the swivel wheel. Be sure to clean the

swivel wheel periodically and as needed.

Wheel

Axle

1. Pull out the swivel wheel.

2. Clean any hair or debris wrapped around the wheel or entangled inside the wheel cavity.

3. Reinstall the wheel and push in until it clicks into place.

• Do not clean the swivel wheel with water.

Clean the mopping module

It is recommended to clean the mopping cloth after each use.

1. Remove the mopping cloth from the module.

2. Clean the cloth with water and air-dry it completely to avoid being mildewed or

producing unpleasant smell.

36 37

Troubleshooting

Problems Solutions

RoboVac cannot be

activated.

• Make sure RoboVac is connected to a power source.

• Make sure the battery is fully charged.

• If you still have trouble, reset the RoboVac (refer to the

“Using Your RoboVac > Reset the System” section in this

manual).

RoboVac suddenly stops

working.

• Check if RoboVac is trapped or stuck on an obstacle.

• Check if the battery level is too low.

• If you still have trouble, turn off RoboVac, wait for 3

seconds, and then turn it back on.

You cannot schedule

cleanings.

• Make sure RoboVac is turned on.

• You can set the time of day and scheduled cleaning time via

the EufyHome app.

• Make sure the scheduled time has been set correctly.

• Check if RoboVac’s power is too low to start cleaning.

• RoboVac will not start a scheduled cleaning while already

performing a task.

Suction power is weak.

• Check if any obstructions are blocking the suction inlet.

• Empty the dust collector.

• Clean the filter with water.

• Check if the filter is wet due to water or other liquid on the

floor. Air-dry the filter completely before use.

RoboVac cannot be

charged.

• Check if the indicator on the Charging Base lights up (when

RoboVac is not on the Charging Base). If not, contact the

eufy service center to repair or replace the Charging Base.

• Check if the indicator on the Charging Base is off and the

light on the main unit is breathing during charging.

• Dust off the charging contact pins with a dry cloth.

RoboVac cannot return to

the Charging Base.

• Remove objects within 1.6 ft/0.5 m to the left and right side

and within 4.9 ft/1.5 m of the front of the Charging Base.

• Make sure RoboVac started cleaning from the Charging

Base and has not been moved during cleaning.

• When RoboVac is in the vicinity of the Charging Base, it

will return more quickly. However, if the Charging Base is

located far away, RoboVac will need more time to return.

Please be patient as it works its way back.

• Clean the charging contact pins.

Problems Solutions

The rolling brush does

not rotate.

• Clean the rolling brush.

• Check if the rolling brush and brush guard have been

installed properly.

RoboVac’s movements or

travel path are abnormal.

• Clean the sensors carefully with a dry cloth.

• Restart RoboVac by turning RoboVac off and on.

Water is not released

during mopping.

• Make sure there is enough water in the water tank.

• Check if the mopping module is correctly installed. Once

correctly installed, you will hear the corresponding voice

prompt.

• Check if the water outlets are blocked.

RoboVac cannot connect

to a Wi-Fi network.

• Make sure your Wi-Fi router supports the 2.4GHz and

802.11b/g/n bands; the 5GHz band is not supported. For

details, refer to the “Troubleshooting > Wi-Fi connection”

section in this manual.

You cannot control

RoboVac with Amazon

Alexa.

• Check if there are any Internet connection problems.

• Check whether you have installed the Amazon Alexa app

onto your smart device and enabled “EufyHome - RoboVac”

Skill in the Amazon Alexa app. For details, refer to the

“Smart Integrations” page in the EufyHome App.

• Make sure you have a EufyHome account and that it is

connected to RoboVac.

• Make sure you are using correct Alexa voice-commands.

You cannot control

RoboVac with the Google

Assistant.

• Check if there are any Internet connection problems.

• Check if you have installed the Google Home app onto

your smart device and initiated the “EufyHome” action

in the Google Home app. For details, refer to the “Smart

Integrations” page in the EufyHome App.

• Check if you are using the proper commands when talking

to the Google Assistant. When making your request, first

say the wake words “Ok Google”.

• Repeat your question. Speak clearly to the Google

Assistant.

La page charge ...

Eufy AK-T2190121 Manuel utilisateur

Marque: Eufy

Modèle: AK-T2190121

Taper: Manuel utilisateur

Ce manuel convient également à

RoboVac L70 Hybrid Robot Vacuum Cleaner

Télécharger le PDF

rapport

dans d''autres langues

English: Eufy AK-T2190121 User manual

Eufy AK-T2190121 Manuel utilisateur

Ce manuel convient également à

Eufy AK-T2190121 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents