Eufy T2150 Le manuel du propriétaire

Marque: Eufy

Modèle: T2150

Taper: Le manuel du propriétaire

RoboVac

Owner’s Manual

T2150/T2151 51005001722 V02

Thank you for purchasing RoboVac. Carefully read all instructions before

using this product, and keep this manual for future reference.

Table of Contents

02 Important Safety Instructions

15 About Your RoboVac

What's in the Box

RoboVac Anatomy

LED Indication

19 Using Your RoboVac

Important Tips Before Use

Preparation

Charge Your RoboVac

Use Your RoboVac with the EufyHome App

Start / Stop Cleaning

Select a Cleaning Mode

Select a Suction Power Level

Use Mopping System

Use Your RoboVac with Amazon Alexa / the

Google Assistant

31 Cleaning and Maintenance

Clean the Dust Collector and Filter

Clean the Side Brushes

Replace the Side Brushes

Clean the Sensors and Charging Pins

Clean the Swivel Wheel

Clean the Mopping Cloth and Water Tank

Replace the Rubber Strip

39 Troubleshooting

Voice Alert

Wi-Fi Connection

44 Speciﬁcations

44 Customer Service

02 03

Important Safety Instructions

To reduce the risk of injury or damage, read these safety

instructions carefully and keep them at hand when setting

up, using, and maintaining this device.

WARNING SYMBOLS USED

This is the safety alert symbol. This symbol alerts you to

potential hazards that could result in property damage

and/or serious bodily harm or death.

• This device can be used by children aged from 8

years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision or

instruction concerning use of this device in a safe way

and understand the hazards involved.

• Children should be supervised to ensure they do not play

with this device.

• Cleaning and maintenance shall not be performed by

children without adult supervision.

• This device is only to be used with the power supply unit

provided.

• Before cleaning or maintaining this device, the plug must

be removed from the socket-outlet.

• The battery in this device should only be replaced by a

skilled professional.

• When removing the battery, disconnect the device from

the supply mains.

• For the purposes of recharging the battery, only use the

detachable power supply unit provided with this device.

• The battery must be removed from this device before

this device is disposed of. To remove the battery from

this device, first remove the screws on the bottom, then

remove the main PCB and unscrew the battery cover

using a screwdriver. Remove the battery by disconnecting

the quick connector.

• The used battery should be placed in a sealed plastic bag

and disposed of safely according to local environmental

regulations.

• The external flexible cable or cord of the power supply

unit cannot be replaced; if the cord is damaged, the

power supply unit shall be disposed of.

• This device is for indoor use only. Do not use outdoors or

on wet surfaces.

• This device is not a toy. Do not sit or stand on this device.

Small children and pets should be supervised when this

device is operating.

• Store and operate this device in room temperature

environments only.

• Clean with a cloth dampened with water only.

• Do not use this device to pick up anything that is burning

or smoking.

• Do not use this device to pick up spills of bleach, paint,

chemicals, or anything wet.

• Before using this device, pick up objects like clothing and

loose paper. Lift up cords for blinds or curtains, and move

power cords and fragile objects out of the way. If this

device passes over a power cord and drags it, an object

could be pulled off a table or shelf.

• If the room to be cleaned has a balcony, a physical barrier

should be used to prevent access to the balcony and to

ensure safe operation.

• Do not place anything on top of this device.

• Be aware that this device moves around on its own.

Take care when walking in the area where this device is

operating to avoid stepping on it.

04 05

• Do not operate this device in areas with exposed

electrical outlets on the floor.

• Do not expose the electronics of this device, its battery,

or the integrated Charging Base. There are no user-

serviceable parts inside.

• Do not use this device on an unfinished, unsealed, waxed

or rough floor. It may result in damage to the floor and

this device. Use only on hard floor surfaces or low-pile

carpet.

• This device has been designed to be used on floors

without scratching them. We still recommend that you

test this device on a small area of the room to be cleaned

to ensure no scratches are made before cleaning the

whole room.

• Only use attachments recommended or described in this

manual.

• Do not handle the appliance or plug with wet hands.

• Ensure that the dust bag and/or filters are in place before

usage.

• Do not use a battery pack or appliance that is damaged

or modified. Damaged or modified batteries may exhibit

unpredictable behavior resulting in fire, explosion or risk

of injury.

• Do not expose the battery pack or appliance to fire or

excessive temperature. Exposure to fire or temperature

above 130°C may cause explosion.

• Do not modify or attempt to repair the appliance or the

battery pack (as applicable), except as indicated in the

instructions for use and care.

• Follow all charging instructions and do not charge the

battery pack or appliance outside of the temperature

range specified in the instructions. Charging improperly

or at temperatures outside of the specified range may

damage the battery and increase the risk of fire.

Notice

This symbol on the device or its packaging

indicates:

Do not dispose of electrical appliances as unsorted

municipal waste; use separate collection facilities.

Contact your local authority for information

regarding the collection systems available. If

electrical appliances are disposed of in landfills or

dumps, hazardous substances can leak into the

groundwater and get into the food chain, damaging

your health and well-being. When replacing old

appliances with new ones, the retailer is legally

obliged to take back your old appliance for disposal

at least free of charge.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) this device must

accept any interference received, including interference that

may cause undesired operation.

Warning: Changes or modiﬁcations not expressly approved

by the party responsible for compliance could void the user's

authority to operate the equipment.

Note: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee

06 07

that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures: (1)

Reorient or relocate the receiving antenna. (2) Increase the

separation between the equipment and receiver. (3) Connect

the equipment into an outlet on a circuit dierent from that to

which the receiver is connected. (4) Consult the dealer or an

experienced radio / TV technician for help.

ISED Compliance Statement

This device contains licence-exempt transmitter(s)/

receiver(s) that comply with Innovation, Science and

Economic Development Canada's licence-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including

interference that may cause undesired operation of the

device.

RF Exposure Compliance Statement

This equipment complies with FCC/IC radiation exposure

limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum

distance 20cm between the radiator and your body.

Declaration of Conformity

This product complies with the radio interference

requirements of the European Community. Hereby, Anker

Innovations Limited declares that the radio equipment

type T2150/T2151/T2250/T2251/T2252 is in compliance

with Directive 2014/53/EU. The full text of the EU

declaration of conformity is available at the following

Maximum output power: 18 dBm

Frequency band: 2.4G band (2.4000GHz - 2.4835GHz)

Contains FCC ID: 2ANDL-WR1 Contains IC: 23243-WR1

GB Declaration of Conformity

Hereby, Anker Innovations Limited declares that

the product type T2150 is in compliance with Radio

Equipment Regulations 2017 and The Restriction of the

Use of Certain Hazardous Substances in Electrical and

Electronic Equipment Regulations 2012. The full text of the

UK declaration of conformity is available at the following

internet address: https://www.eufy.com

Trademark Notice

• Amazon, Echo, Alexa and all related logos are trademarks

of Amazon.com, Inc. or its affiliates.

• Apple and the Apple logo are trademarks of Apple Inc.,

registered in the U.S. and other countries. App Store is

a service mark of Apple Inc., registered in the U.S. and

other countries.

• Google Play and the Google Play logo are trademarks of

Google Inc.

• Google Home is a trademark of Google Inc.

08 09

Consignes importantes de sécurité

Pour réduire le risque de blessure ou de dommage, lisez

attentivement les consignes de sécurité et gardez-les

à portée de main lors de la configuration, l'utilisation et

l'entretien de cet appareil.

SYMBOLES D'AVERTISSEMENT UTILISÉS

Il s'agit du symbole d'avertissement de sécurité. Ce

symbole vous alerte sur les dangers potentiels qui

peuvent entraîner des dommages matériels et/ou des

lésions corporelles graves ou la mort..

• Cet appareil peut être utilisé par des enfants âgés de

8 ans et plus, ainsi que des personnes présentant des

capacités physiques, sensorielles ou mentales réduites,

ou un manque d'expérience et de connaissances,

si celles-ci sont sous surveillance ou ont reçu les

instructions d'utilisation de cet appareil et comprennent

les risques encourus, et l'utilisent dans un endroit sûr.

• Les enfants doivent être surveillés afin de s'assurer qu'ils

ne jouent pas avec cet appareil.

• Le nettoyage et l'entretien ne doivent pas être effectués

par des enfants sans la supervision des adultes.

• Cet appareil doit uniquement être utilisé avec le bloc

d'alimentation fourni.

• Avant de nettoyer ou d'entretenir cet appareil, vous

devez débrancher la fiche de la prise de courant.

• La batterie de cet appareil ne doit être remplacée que par

un professionnel qualifié.

• Lorsque vous retirez la batterie, débranchez l'appareil du

secteur.

• Pour recharger la batterie, utilisez uniquement le cordon

amovible du bloc d'alimentation fourni avec cet appareil.

• La batterie doit être retirée de cet appareil avant de le

mettre au rebut. Pour retirer la batterie à partir de cet

appareil, retirez d'abord les vis de la partie inférieure,

puis retirez le circuit principal et dévissez le couvercle de

la batterie à l'aide d'un tournevis. Retirez la batterie en

débranchant le connecteur rapide.

• La batterie usagée doit être placée dans un sac en

plastique hermétique et éliminée en toute sécurité,

conformément aux réglementations environnementales

locales.

• Le câble flexible externe ou le cordon du bloc

d'alimentation ne peut pas être remplacé ; si le cordon

est endommagé, l'unité d'alimentation doit être éliminée.

• Cet appareil est destiné exclusivement à une utilisation

en intérieur. Ne pas utiliser à l'extérieur ou sur des

surfaces humides.

• Cet appareil n'est pas un jouet. Ne pas se tenir debout

ou assis sur cet appareil. Les jeunes enfants et les

animaux de compagnie doivent être surveillés lors du

fonctionnement de cet appareil.

• Entreposez et utilisez cet appareil dans des

environnements à température ambiante.

• Nettoyez avec un chiffon imbibé d'eau uniquement.

• Ne pas utiliser cet appareil pour ramasser tout élément

en train de brûler ou fumant.

• Ne pas utiliser cet appareil pour ramasser des

déversements d'eau de javel, de peinture, de produits

chimiques ou quoi que ce soit de mouillé.

• Avant d'utiliser cet appareil, ramassez les objets tels que

les vêtements et les feuilles de papier. Mettez en hauteur

les cordons de stores ou de rideaux au sol et déplacez

les objets fragiles et les cordons d'alimentation hors du

passage de l'appareil. Si cet appareil passe au-dessus

10 11

d'un cordon d'alimentation et le traîne avec lui, un objet

peut tomber d'une table ou d'une étagère.

• Si la pièce à nettoyer possède un balcon, une barrière

physique doit être utilisée pour empêcher l'accès au

balcon et garantir un fonctionnement sécurisé.

• Ne rien placer sur le dessus de cet appareil.

• Gardez à l'esprit que cet appareil se déplace par ses

propres moyens. Faites attention en marchant dans la

zone où cet appareil fonctionne, afin d'éviter de marcher

dessus.

• Ne pas utiliser cet appareil dans des zones avec prises

électriques exposées sur le plancher.

• Ne pas exposer l'électronique de cet appareil, de sa

batterie ou de la base de recharge intégrée. L'appareil ne

contient aucune pièce réparable par l'utilisateur.

• Ne pas utiliser cet appareil sur un sol inachevé,

non vitrifié, ciré ou rugueux. Cela peut entraîner

des dommages sur le sol et cet appareil. Utilisez-le

uniquement sur des surfaces dures ou des moquettes à

poils ras.

• Cet appareil a été conçu pour être utilisé sur des

planchers sans le rayer. Nous vous recommandons de

toujours tester le périphérique sur une petite zone de la

pièce à nettoyer, avant de nettoyer la salle entière, pour

s'assurer qu'aucune rayure n'apparaisse.

• Utilisez uniquement les accessoires recommandés ou

décrits dans ce manuel.

• Ne manipulez pas l'appareil ou la fiche avec les mains

mouillées.

• Assurez-vous que le sac à poussière et/ou les filtres sont

en place avant utilisation.

• N'utilisez pas de batterie ou d'appareil endommagé

ou modifié. Les batteries endommagées ou modifiées

peuvent présenter un comportement imprévisible

risquant d'entraîner un incendie, une explosion ou une

blessure.

• N'exposez pas la batterie ou l'appareil au feu ou à des

températures excessives. L'exposition au feu ou à une

température supérieure à 130°C peut provoquer une

explosion.

• Ne modifiez pas et n'essayez pas de réparer l'appareil ou

la batterie (si applicable), sauf si cela est indiqué dans les

instructions d'utilisation et d'entretien.

• Suivez toutes les instructions de chargement et ne

chargez pas la batterie ou l'appareil en dehors de la plage

de température spécifiée dans les instructions. Une

charge incorrecte ou à des températures hors de la plage

spécifiée peut endommager la batterie et augmenter le

risque d'incendie.

Avis

Ce symbole sur le produit ou son emballage indique :

Ne pas jeter les appareils électriques de la même

manière que les déchets municipaux non triés ;

utilisez une infrastructure de collecte séparée.

Contactez directement votre commune pour

plus d'informations concernant les systèmes de

collecte disponibles. Si des appareils électriques

sont jetés dans des décharges ou des dépotoirs,

des substances dangereuses peuvent s'infiltrer

dans les eaux souterraines et entrer dans la chaîne

alimentaire, nuire à votre santé et votre bien-être.

Quand vous remplacez vos anciens appareils par

de nouveaux, le détaillant est légalement obligé

de reprendre votre ancien appareil pour son

élimination, au minimum gratuitement..

12 13

Déclaration FCC

Cet appareil est conforme au Chapitre 15 du règlement

FCC. Le fonctionnement est soumis aux deux conditions

suivantes : (1) l'appareil ne doit pas produire de brouillage,

et (2) l'utilisateur de l'appareil doit accepter tout brouillage

radioélectrique subi, même si celui-ci est susceptible d'en

compromettre le fonctionnement.

Avertissement : Les changements non expressément

approuvés par la partie responsable de la conformité pourraient

entraîner une annulation de l'autorisation d'utilisation de

l'équipement.

Remarque : cet appareil a été testé et déclaré conforme aux

limites d'un appareil numérique de Classe B conformément

au Chapitre 15 de la réglementation FCC. Ces limites sont

établies pour assurer une protection raisonnable contre les

interférences nuisibles dans une installation résidentielle.

Cet appareil génère, utilise et peut émettre des fréquences

radio qui peuvent causer des interférences nuisibles aux

radiocommunications si l'appareil n'est pas installé et utilisé

conformément aux instructions. Il n'est pas garanti toutefois

que de telles interférences ne se produisent pas dans une

installation donnée. Si cet appareil provoque des interférences

nuisibles à la réception de la radio ou de la télévision, ce

qui peut être déterminé en mettant en route l'appareil et

en l'arrêtant, il est recommandé d'essayer de corriger les

interférences en prenant l'une ou plusieurs des mesures

suivantes : (1) réorienter ou déplacer l'antenne de réception,

(2) augmenter la distance entre l'appareil et le récepteur,

(3) brancher l'appareil sur une prise alimentée par un circuit

diérent de celui qui alimente le récepteur , (4) consulter le

revendeur ou un technicien expérimenté en radio/télévision

pour assistance.

L'émetteur/récepteur exempt de licence contenu dans

le présent appareil est conforme aux CNR d'Innovation,

Sciences et Développement économique Canada

applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes :

1. L'appareil ne doit pas produire de brouillage;

2. L'appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

Cet équipement est conforme aux limites d'exposition aux

radiations FCC/IC établies pour un environnement non

contrôlé. Cet équipement doit être installé et utilisé avec

une distance minimale de 20 cm entre le radiateur et votre

corps.

Déclaration de conformité

Ce produit est conforme aux exigences en matière

d'interférences radio de la Communauté européenne.

Par les présentes, Anker Innovations Limited déclare que

l'équipement radio de type T2150/T2151/T2250/T2251/

T2252 est conforme à la directive 2014/53/UE. Le texte

complet de la déclaration de conformité UE est disponible

à l'adresse Internet suivante : https://www.eufylife.com/.

Puissance de sortie maximale : 18 dBm

Bande de fréquence : Bande 2,4 G (2,4000 GHz - 2,4835 GHz)

14 15

Avis de marque déposée

• Amazon, Echo, Alexa et tous les logos associés sont des

marques commerciales d'Amazon.com, Inc. ou de ses

filiales.

• Apple et le logo Apple sont des marques déposées

d'Apple Inc., enregistrées aux États-Unis et dans d'autres

pays. App Store est une marque de service d'Apple Inc.,

enregistrée aux États-Unis et dans d'autres pays.

• Google Play et le logo Google Play sont des marques de

Google Inc.

• Google Home est une marque de Google Inc.

About Your RoboVac

What's in the Box

RoboVac Power Adapter

Cleaning ToolSide Brushes (x4)

Water Tank

Filter Elements (x4)

Charging Base

Additional Filter

Waterproof PadWashable Mopping Cloth (x2)

Owner’s Manual &

Other Documents

Cable Ties (x5)

16 17

RoboVac Anatomy

A. Top & Side

Wi-Fi status light

Bumper

Dust collector

Dust collector release button

Infrared sensor

Auto cleaning control button

B. Bottom

Dust collector

Cover plate

Rubber strip

Charging contact pins Charging contact pins

Side brushes

Wheels

Main power switch (On/O)

Drop sensor

Swivel wheel

C. Dust Collector

Filter

D. Suction Inlet

Dust collector

Suction inlet Suction inlet

E. Charging Base

Status light

Power cord storage

compartment

Power socket

Charging contact pins

18 19

F. Water Tank

Washable mopping cloth

Fliter element

Cloth attachment area

Slot

Fliter element

Movable pulley

Water inlet

Snap joints Snap joints

Water inlet cover

LED Indication

You can see the status of RoboVac from the LED indicators.

(Power Status Light) Status

Breathing orange Charging

Solid blue Standby / Cleaning / Fully charged

Solid orange Low power and returning to Charging Base

O

• RoboVac is off.

• To conserve power, the light automatically turns off

when RoboVac is not docked to the Charging Base

and has been inactive for 10 minutes.

Flashing red + Voice alert

RoboVac has an error.

Refer to the “Troubleshooting>Voice Alert” section in

this manual for solutions.

(Wi-Fi Status Light) Status

Slowly ﬂashing blue Waiting for connection

Rapidly ﬂashing blue Connecting with your wireless router

Solid blue Connected to your wireless router

Using Your RoboVac

Important Tips Before Use

abc

def

Remove power cords and small objects from the floor that may entangle RoboVac.

You can use the supplied cable ties to organize your wires and power cords.

Fold tasseled edges of area rugs underneath to prevent tangling RoboVac. Avoid

cleaning very dark-colored high-pile rugs or rugs thicker than 1.02 in/26 mm as

they may cause RoboVac to malfunction.

Keep RoboVac away from spaces lower than 2.87 in/73 mm to prevent RoboVac

from getting stuck. If necessary, place a physical barrier to block off the problem

areas.

Keep RoboVac away from wet areas.

RoboVac may climb on top of objects less than 0.63 in/16 mm in height. Remove

these objects if possible.

20 21

Anti-drop sensors will prevent RoboVac from tumbling down stairs and steep drops

in most cases. Sensors are less effective if dirty or used on carpeted/reflective/very

dark-colored floors. It is recommended to place physical barriers to block off areas

where RoboVac may fall.

Place physical barriers in front of fireplaces and areas that may cause damage to

RoboVac if entered.

Preparation

Remove the foam blocks beside the bumper before use.

Install the side brushes before use.

Before mopping, attach the waterproof pad to the Charging Base to keep the ﬂoor

dry. Make sure it is ﬁrmly installed. If mopping is not needed, you can skip this

step.

Turn on the main power switch on the bottom of RoboVac.

OFF ON

Place the Charging Base on a level surface and against a wall.

Remove objects within 3 ft/1 m of the left and right side and within 6 ft/2 m of

the front of the Charging Base. If you cannot remove the objects, check whether

RoboVac can return to the Charging Base normally; if not, contact eufy customer

service for help.

22 23

Connect the round connector of the adapter into the power socket on the

Charging Base and the other end into a wall outlet.

When the Charging Base connects to AC power, the LED indicator on the

Charging Base is SOLID WHITE.

• Install the Charging Base in a location that RoboVac can easily access. It is

recommended to place the Charging Base against a wall, and on a hard-level

surface rather than on rugs or carpets.

• Always keep the Charging Base plugged in, otherwise RoboVac will not

automatically return to it.

Charge Your RoboVac

• RoboVac has a pre-installed rechargeable battery that has to be fully charged before

use.

• RoboVac returns to the Charging Base at the end of a cleaning cycle or when its

battery is running low.

Attach RoboVac to the Charging Base by aligning its charging pins with the charging

pins on the base.

• Turn off the main power switch if RoboVac will not be used for a long

period of time. To preserve the battery’s lifespan, recharge at least once

every 6 months.

Use Your RoboVac with the EufyHome App

To enjoy all available features, it is recommended to control your RoboVac via the

EufyHome app.

Before you start, make sure that:

• Your smartphone or tablet is connected to a Wi-Fi network.

• Your smartphone or tablet is running iOS 8.0 (or above) or Android 4.4 (or above).

• The 2.4GHz band wireless signal is enabled on your wireless router.

• The Wi-Fi status light on RoboVac is slowly flashing blue.

• RoboVac is attached to the Charging Base to ensure it has enough power during

setup.

EufyHome

1. Download the EufyHome app from the App Store (iOS devices) or Google Play

(Android devices).

2. Open the app and create a user account.

3. Tap the “+” icon to add RoboVac to your EufyHome account.

4. Follow the instructions in the app to set up the Wi-Fi connection.

- After connecting successfully, you can control RoboVac via the app.

- With the app, you can select a cleaning mode, set the time, schedule a cleaning,

view the system status, receive notifications and access additional features.

24 25

Wi-Fi Status Light

Slowly flashing blue Waiting for connection

Rapidly flashing blue Connecting with your wireless router

Solid blue Connected with your wireless router

• If you have any problems during the Wi-Fi setup process, refer to the

“Troubleshooting > Wi-Fi connection” section in this Manual.

• If RoboVac gets stuck in any space, tap Find My Robot in the app to find

the machine.

Restore Factory Settings

Press and hold on RoboVac for 10 seconds to restore factory settings if necessary.

- You will hear a voice prompt when the settings have been reset and the Wi-Fi

status light will slowly flash blue. Now you can follow the Wi-Fi instructions in the

EufyHome app to set up the Wi-Fi connection.

Schedule Cleaning

With the EufyHome app, you can schedule RoboVac to start cleaning at a particular

time.

• You can set the time and customize the cleaning schedules from Sunday

to Saturday on the EufyHome app. This function is available in the app

only.

Start / Stop Cleaning

• Make sure the main power switch on the bottom of RoboVac is turned

on before use.

• You can also start or stop cleaning via the EufyHome app.

Press on RoboVac to start cleaning in Auto Mode.

Press again to pause cleaning.

Select a Cleaning Mode

Auto cleaning

After startup, RoboVac moves from the Charging Base and automatically determines

its cleaning route, following a bow-shaped cleaning method. When the entire clean is

finished, RoboVac automatically returns to the Charging Base.

26 27

Press on RoboVac to start cleaning in Auto Mode.

• During cleaning, RoboVac will return to the Charging Base automatically

if the battery level becomes low. Once recharged, RoboVac will resume

to finish the remaining cleaning.

• By default, RoboVac starts in Auto cleaning mode when it is turned on.

Spot cleaning

You can select the Spot cleaning mode in the EufyHome app. In Spot mode, RoboVac

intensively cleans a specific area for 2 minutes in a spiral pattern. Useful if there is a

concentrated area of dust or debris.

EufyHome

Select a Suction Power Level

In the EufyHome app, select a suction power level according to your needs:

• Standard (Default)

• Max

When RoboVac starts cleaning the next time, it will clean according to the

suction power level you previously selected.

Use Mopping System

• The mopping mode is not recommended when no one is at home.

• Only use the mopping mode on a floor without carpets.

• Remove the water tank when RoboVac is under charging or not in use.

Before mopping, install the waterproof pad under the Charging Base to protect

the ﬂoor.

Wet the mopping cloth and wring it until it does not drip. Insert the cloth along

the bracket slot and stick it ﬁrmly.

28 29

Open the water inlet cover to ﬁll the water, then close the cover.

Do not use floor cleaner or detergent which may block the filter elements.

Install the water tank into the bottom of RoboVac until a click is heard.

The mopping mode is only intended for a clean floor without stubborn

stains. To achieve a better mopping effect, it is recommended to clean the

floor with RoboVac three times before installing the mopping module.

Select a cleaning mode to start cleaning.

- RoboVac automatically sweeps and mops in the selected mode.

When RoboVac ﬁnishes working and returns to the Charging Base, press the

release button to remove the dust collector and the water tank.

Remove the water tank and put the dust collector back into the main unit.

• After mopping, remove the water tank, empty any remaining water and

clean the mopping cloth to prevent the cloth becoming mildewed or

producing peculiar smell. For how to clean and maintain the water tank,

refer to the “Cleaning and Maintenance” section in this manual.

30 31

Use Your RoboVac with Amazon Alexa / the Google

Assistant

Amazon Alexa or the Google Assistant is a smart voice control device that enables

you to control RoboVac with your voice.

Currently this feature only supports English, German, French, and Spanish. You

could check regularly if more languages are supported at https://www.eufylife.com/

support/.

Before you start, make sure that:

• RoboVac is attached to the Charging Base to ensure there is enough power.

• RoboVac is connected with the EufyHome app.

• You have an Amazon Alexa-enabled device (i.e. Amazon Echo, Echo Dot and

Amazon Tap, Echo Show, Echo Spot) or a device enabled with the Google Assistant

(i.e. Google Home, Google Home Mini). These devices are sold separately.

• The Amazon Alexa app or Google Home app is already installed on your smart

device, and you have created an account.

To control RoboVac with Amazon Alexa or the Google

Assistant

1. Open the EufyHome app and find “Smart integrations” in the top left.

2. Follow the on-screen instructions to complete the setup.

• For more information about how RoboVac works with Amazon Alexa /

the Google Assistant, visit https://www.eufylife.com/support/ for

details.

Cleaning and Maintenance

For optimal performance, follow the instructions below to clean and maintain RoboVac

regularly. The cleaning/replacement frequency will depend on your usage habits of

RoboVac.

Recommended cleaning/replacement frequency

RoboVac Part Cleaning Frequency Replacement Frequency

Dust Collector After each use -

Filter Once every week

(Twice a week if you have a pet)

Every 6 months or after every

50 rounds of cleaning

Side Brushes Once every month Every 3-6 months (or when

visibly worn)

Rubber Strip Once every week Every 6 months (or when

visibly worn)

Filter Elements - Every 6 months (or when

they become yellow)

Sensors Once every month -

Charging Pins Once every month -

Swivel Wheel Once every month -

Mopping Cloth After each use -

Water Tank After each use -

Clean the Dust Collector and Filter

Press the dust collector release button to pull the dust collector out.

32 33

Open and empty the dust collector.

Remove the ﬁlter.

Rinse the dust collector and ﬁlter thoroughly with water.

1min

Do not use a brush, hot water, or any detergent to clean the filter.

Air-dry the dust collector and ﬁlter completely before next use. You may change

to use the other ﬁlter if the original one is not completely dry.

24h

Place the ﬁlter back into the dust collector.

Push the dust collector back into the main unit.

34 35

Clean the Side Brushes

Foreign substances, such as hair, can easily get tangled in the side brushes, and dirt

may adhere to them. Be sure to clean them regularly.

Remove the side brushes.

Carefully unwind and pull o any hair or string that is wrapped between the main

unit and the side brushes.

Use a cloth dampened with warm water to remove dust from the brushes or to

gently reshape them.

Only use the side brushes when they are completely dry.

Replace the Side Brushes

The side brushes may become bent or damaged after being used for a period of time.

Follow the instructions below to replace them.

• Pull off the old side brushes and snap the new ones into place.

Clean the Sensors and Charging Pins

To maintain the best performance, clean the drop sensors and charging pins regularly.

• Dust off the drop sensors and charging contact pins using a cloth or cleaning brush.

36 37

Clean the Swivel Wheel

Hair or dust particles can easily get entangled in the swivel wheel. Be sure to clean the

swivel wheel periodically and as needed.

Wheel

Axle

Remove the swivel wheel.

Clean any hair or debris wrapped around the wheel or entangled inside the wheel

cavity.

Reinstall the wheel and push in until it clicks into place.

Do not clean the swivel wheel with water.

Clean the Mopping Cloth and Water Tank

It is recommended to clean the mopping cloth and water tank after each use.

24h

After each use, remove the mopping cloth from the water tank.

Rinse the mopping cloth and water tank thoroughly with water.

Air-dry the mopping cloth and water tank completely to avoid being mildewed or

producing unpleasant smell.

Replace the Rubber Strip

Turn over the main unit, and remove the screws.

Remove the cover plate and then take out the rubber strip.

La page est en cours de chargement...

Eufy T2150 Le manuel du propriétaire

Marque: Eufy

Modèle: T2150

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Eufy T2150 Owner's manual

Eufy T2150 Le manuel du propriétaire

Eufy T2150 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents