Kobalt SGY-AIR135TZ Manuel utilisateur

Français p. 16

Español p. 31

ATTACH YOUR RECEIPT HERE

etaD esahcruP rebmuN laireS

Questions, problems, missing parts? Before returning to your retailer, call

our customer service department at 1-888-3KOBALT, 8:00 a.m.-8:00 p.m.,

EST, Monday-Friday.

1

ITEM #0075988

MODEL #SGY-AIR135TZ

AB13758

KOBALT

®

and the K Design

®

are registered

6 IN. DUAL ACTION SANDER

TABLE OF CONTENTS

2

Safety Information ............................................................................................... 3

Product Specifications ........................................................................................ 3

Package Contents ............................................................................................... 9

Preparation .......................................................................................................... 9

Assembly Instructions ........................................................................................ 10

Operating Instructions ........................................................................................ 12

Care and Maintenance ....................................................................................... 13

Troubleshooting .................................................................................................. 13

Warranty ............................................................................................................. 14

.................................................................................................... 15

IMPORTANT: To operate correctly, this tool requires airflow that is at least 5 cubic feet per

minute (CFM) at 90 pounds per square inch (PSI). Check the specifications of your air compressor

to be sure that it can support both the minimum CFM and PSI required. An air hose may cause

up to 15 PSI drop in pressure, so you may need to set the output higher to maintain the required

pressure at the tool.

Exploded View

3

SPECIFICATIONS

6 IN.

10,000 RPM +/- 10%

5 CFM

1/4 IN. NPT

3/8 IN.

90 PSI

COMPONENT

PRODUCT SPECIFICATIONS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate

or install the product. If you have any questions regarding the product, please call

customer service at 1-888-3KOBALT, 8:00 a.m.-8:00 p.m., EST, Monday-Friday.

Improper operation or maintenance of this product could result in serious injury and

property damage. Read and understand all warnings and operation instructions

before using this equipment. When using air tools, basic safety precautions should

always be followed to reduce the risk of personal injury.

WARNING

SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING

AND OTHER RELATED ACTIVITIES CONTAINS CHEMICALS KNOWN TO THE

STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER

REPRODUCTIVE HARM. A LISTING OF CHEMICALS CAN BE OBTAINED FROM

www.oehha.ca.gov UNDER PROPOSITION 65. SOME EXAMPLES OF THESE

CHEMICALS ARE:

LEAD FROM LEAD-BASED PAINTS

CRYSTALLINE SILICA FROM BRICKS, CEMENT AND OTHER MASONRY

PRODUCTS

ARSENIC AND CHROMIUM FROM CHEMICALLY-TREATED LUMBER

WARNING

YOUR RISK FROM THESE EXPOSURES VARIES, DEPENDING ON HOW OFTEN

YOU DO THIS TYPE OF WORK. TO REDUCE YOUR EXPOSURE TO THESE

CHEMICALS WORK IN A WELL VENTILATED AREA, AND WORK WITH

APPROVED

SAFTEY EQUIPMENT, SUCH AS A RESPRIATOR OR DUST MASKS

WHICH ARE SPECIALLY DESIGNED TO FILTER MICROSOPIC PARTICLES.

SANDING PAD

FREE SPEED

AVERAGE AIR CONSUMPTION

AIR INLET

AIR HOSE

WORKONG PRESSURE

RISK OF EYE OR HEAD INJURY

WHAT COULD HAPPEN HOW TO PREVENT IT

This particular air powered tool can be

capable of propelling materials such as

fasteners, metal chips, sawdust, and

other debris at high speed which could

result in serious injury.

Compressed air can be hazardous and

propel objects and other particles that

can cause injury to soft tissue areas of

the body, such as eyes and ears.

Particles or objects propelled by the

stream can cause injury.

Tools attachments can become loose

or break and fly apart propelling articles

at the operator and others in the work

area.

Always wear ANSI approved Z87.1

safety glasses with side shields.

Never leave operating tool unattended.

Disconnect air hose when tool is not in

use, and place in a safe area.

For additional protection, use an

approved face shield in addition to

safety glasses.

Make sure that any attachments are

securely fastened and properly

assembled before use.

WARNING

Always use the tool at a safe distance

from others in the work area and ensure

the work area is safe at all times.

WHAT COULD HAPPEN HOW TO PREVENT IT

WARNING

A DA sander is capable of

generating sparks which can result

in ignition of flammable materials.

RISK OF FIRE OR EXPLOSION

Never operate tools near flammable

substances such as gasoline, naphtha,

cleaning solvents, etc.

Work in a clean, well ventilated area

free of combustible materials.

Never use oxygen, carbon dioxide or

other bottled gasses as a power source

for air tools.

4

SAFETY INFORMATION

WHAT COULD HAPPEN HOW TO PREVENT IT

WARNING

RISK OF LOSS OF HEARING

Always wear ANSI S3.19 hearing

protection.

Exposure to noise produced from the

operation of air tools can lead to

permanent hearing loss.

5

SAFETY INFORMATION

Tools which contain moving elements

or drive other moving parts, such as

impact sockets, can become entangled

in hair, clothing, jewelry and other loose

objects, resulting in severe injury.

WHAT COULD HAPPEN HOW TO PREVENT IT

WARNING

RISK OF ENTANGLEMENT

Do not wear loose clothing, jewelry, or

anything that may get caught or tangled

when using tool.

Remove any jewelry which may be

caught by the tool.

Always keep hands and body parts

away from moving parts

Always wear proper fitted clothing and

other properly fitted safety equipment

when using this tool.

WHAT COULD HAPPEN HOW TO PREVENT IT

WARNING

RISK OF CUT OR BURNS

Keep the working part of the tool away

from hands and body.

A DA sander is capable of causing

serious injury if operated in an improper

way, or used in a manner which is not

intended for the tool.

WHAT COULD HAPPEN HOW TO PREVENT IT

WARNING

RISK OF ELECTRIC SHOCK

Air tool accessories such as impact

sockets that come into contact with

hidden electrical wiring could cause

electrocution or death.

Thoroughly investigate the work

piece/area for possible hidden wiring

before performing work.

Using air tools to attached electrical

wiring can result in electrical shock,

electrocution, or death.

This tool is not provided with an

insulated gripping surface. Contact with

a “live” wire will also make exposed

metal parts of the tool “live” and can

result in electrical shock, electrocution

or death.

Never use tools attached to electrical

wiring while energized.

Avoid body contact with grounded

surfaces such as pipes, radiators,

refrigerators, and ranges. There is

an increased risk of electrical shock if

your body is grounded.

6

SAFETY INFORMATION

WHAT COULD HAPPEN HOW TO PREVENT IT

WARNING

RISK OF PERSONAL INJURY

A tool left unattended or with the air

hose attached can be activated by

unauthorized persons leading to their

injury or injury to others.

Air tools can propel fasteners or other

materials throughout the work area.

Always make sure to remove the

wrench key before operating. A wrench

key that is left attached to a rotating

part of the tool increases the risk of

personal injury.

Using inflator nozzles for duster

applications can cause serious injury.

Air tools can become activated by

accident during maintenance or tool

changes.

Air tools can cause the workpiece to

move upon contact, leading to injury.

Remove air hose when tool is not in use

and store tool in secure location away

from reach of children and untrained

users.

Use only parts, fasteners and accessories

recommended by the manufacturer.

Keep work area clean and free of

clutter. Do not allow children to operate

tool, and keep children away from the

work area.

Keep work area well lit.

Remove adjusting keys and wrenches

before turning the tool on.

DO NOT use inflator nozzles for duster

applications.

Remove air hose to lubricate or add

impact sockets to the tool.

Never carry the tool by the air hose.

Always carry the tool by the handle.

Avoid unintentional starting. Never carry

the tool with the trigger depressed or

engaged.

Only an authorized service

representative should do repair

servicing.

Use clamps or other devices to prevent

movement.

Loss of control of the tool can lead to

injury to self or others in the work area.

Never use the tool while using drugs or

alcohol.

Before changing accessories, when

making repairs, or when tool is not in

use, always first shut off air supply and

release/drain air pressure from hose.

Then disconnect tool from air supply or

hose and store in a safe location.

7

SAFETY INFORMATION

Loss of control of the tool can lead to

injury to self of others in the work area.

Poor quality, improper or damaged

tools and attachments can fly apart

during operation, propelling particles

through the work area causing serious

injury.

Improperly maintained tools and

accessories can cause serious injury.

There is a risk of bursting if the tool is

damaged.

Keep proper footing at all times. Do not

overreach, as slipping, tripping, and or

falling can be a major cause of serious

injury and or death. Be aware of

excess air hose and power plugs in the

working area or work surface.

Keep handles dry, clean and free from

oil/grease.

Stay alert. Watch what you are doing.

Use common sense. Do not operate

tool when you are tired.

Always use tools attachments rated for

the speed of the power tool.

Never use tools, which have been

dropped, impacted, or are damaged.

Use only impact grade sockets with

this tool.

Do not apply excessive force to the tool;

let the tool perform the work.

Maintain the tool and accessories

with care.

Keep tools clean properly oiled for best

and safest performance.

Check for misalignment or binding of

moving parts, breakage of parts and

any other condition that affects the

tool's operation. If damaged, have the

tool serviced before using.

Never use a tool that is leaking air, has

missing or damaged parts, or requires

repairs.

Wiping or cleaning flammable waste

materials that may have been used on

tool must be placed in a tightly closed

metal container, and disposed of in

a proper manner.

WHAT COULD HAPPEN HOW TO PREVENT IT

WARNING

RISK OF PERSONAL INJURY

8

There is a risk of bursting if the tool is

damaged.

Use of an accessory not intended for

use with a specific tool increases the

risk of injury to operator and anyone in

the work area.

Use of an accessory not intended for

use with the specific tools increases the

risk of injury to persons.

Follow lubrication instructions for best

and safest operation.

Follow assembly and repair instructions

on how to properly change accessories.

WHAT COULD HAPPEN HOW TO PREVENT IT

WARNING

RISK OF PERSONAL INJURY

WHAT COULD HAPPEN HOW TO PREVENT IT

WARNING

INHALATION HAZARD

Abrasive tools, such as grinders,

sanders and cut-off tools generate dust

and abrasive materials, which can be

harmful to human lungs and respiratory

system.

Some materials such as adhesives and

tar contain chemicals whose vapors

could cause serious injury with

prolonged exposure.

Always wear properly fitting facemask

or respirator when using such tools.

Always work in a clean, dry,

well-ventilated area.

SAFETY INFORMATION

9

Before beginning the assembly of the product, make sure all parts are present.

Compare parts with package contents list. If any part is missing or damaged,

do not attempt to assemble the product. Contact customer service for replacement

parts.

Estimated Assembly Time: 5-10 minutes

Tools Required for Assembly (not included): Adjustable wrench

PACKAGE CONTENTS

PREPARATION

DESCRIPTION

6 in. DA Sander

Sanding Pad

Bearing Seat

Inertia Nut

Air Regulating Knob

Trigger

Air Inlet

QUANTITY

1

PART

A

B

C

D

E

F

G

A

F

B

E

G

C

D

ASSEMBLY INSTRUCTIONS

10

2

3

1

1. Remove the air inlet protective cap from the

air inlet (G) (See Figure 1).

3. Insert a male plug (not provided) by hand into

the air inlet (G) (See Figure 2).

4. Place 2-3 drops of air tool oil (not provided)

into the male plug before each use (See

Figure 3).

Use threaded sealant tape (not included) on the

threading of the male plug. Once sealant

tape is properly in place, tighten male plug

turning clockwise with a wrench (not included)

for air tight connection.

DO NOT OVERTIGHTEN.

2.

ASSEMBLY INSTRUCTIONS

5. Rotate the inertia nut (D) and get the gear to

face the bearing seat (C). Then the bearing

seat (C) is locked and stable (See Figures 4)

6. To properly mount the sanding pad (B) to the

the bearing seat (C), remove the plastic

cap protecting the threads on the sanding

pad (B). Align the threads of sanding pad (B)

onto the bearing seat (C) and turn the pad

clockwise by hand. Make sure that the

sanding pad (B) is fixed tightly (See Figure 5).

11

7. Mount sanding paper (not provided) onto the

sanding pad (B).

4

Unlocked

WARNING

Only use sanding paper which has an RPM rating

equal or greater than 10,000 RPM.

Before using tool, always make sure attachments

are properly mounted/secured. If attachments are

not properly mounted/secured, they can present

a serious hazard and may cause bodily injury for

the operator or anyone in or around the work area.

Always follow the attachment manufacturer’s

specifications for properly attaching accessories

to tool.

5

plastic cap

Locked

6

Unlocked

After mounting of sanding pad (B), rotate the

inertia nut (D) 90°to unlocked position

(See Figure 6).

1

2

OPERATING INSTRUCTIONS

1. Press the trigger (F) to start the tool (See

Figure 1).

NOTE The tool features an air regulating knob

(E). The tool speed can be adjusted by turning

the air regulator knob (E) either clockwise or

counterclockwise. The maximum tool speed can

be obtained when the concave line on the knob

(E) is pointing at horizontal (See Figure 2).

12

When first making contact with the surface you

intend to sand, ensure the speed is set to the

lowest setting. Gradually increase the power/speed

as needed for your particular sanding application(s)

instead of using too much power/speed from the

start.

ASSEMBLY INSTRUCTIONS

7

Connect the air supply hose to the male plug. Set

the working pressure at 90 PSI for best tool

performance (See Figure 7).

NOTE Working pressure refers to the air line

pressure set to tool when tool is under working

conditions.

13

CARE AND MAINTENANCE

1. Flush the tool with air-tool oil or gum

solvent.

2. Lubricate the tool.

3. a. Adjust the regulator on the tool to

maximum setting.

b. Adjust the compressor regulator to tool

maximum of 90 PSI.

4. Tighten and seal hose fittings if leaks are

found. Use sealing tape.

5. a. Be sure the hose is the proper size.

Long hose or tools using large volumes

of air may require a hose with an I.D. of

1/2 in. or larger depending on the total

length of the hoses.

b. Do not use a multiple number of hoses

with quick-connect fittings. This causes

additional pressure drop and reduces the

tool power. Always directly connect the

hoses together.

Tool runs

slowly or will

not operate

1. Grit or gum in tool.

2. No oil in tool.

3. Low air pressure.

4. Air hose leaks.

5. Pressure drops.

PROBLEM

TROUBLESHOOTING

CORRECTIVE ACTIONPOSSIBLE CAUSE

Always remove tool from air supply before performing any maintenance on tool.

An in-line oiler (not included) is recommended to be installed to air supply. It will help

increase tool life and keep the tool properly lubricated. The in-line oiler should be

regularly checked and filled with air tool oil as needed. To check if the in-line oiler is

properly lubricating the tool, place a sheet of paper next to the tool’s exhaust ports

while holding the throttle completely open for 30 seconds. The in line oiler is properly

set when a light stain of oil collects on the paper. Excessive amounts of oil should be

avoided. In the event that it becomes necessary to store the tool for an extended

period of time, the tool should receive a generous amount of lubrication right before

being stored. After being well lubricated, the tool should be run for approximately 30

seconds to ensure oil has been evenly distributed throughout the tool. The tool should

be stored in a clean and wet dry environment away from the reach of children.

Recommended lubricants: Use air-tool oil or any other high grade turbine oil

containing moisture absorbent, rust inhibitors, metal wetting agent and an EP

(extreme pressure) additive. Consult your local retailer for further assistance

in selecting which air tool oil is best suited for proper lubrication.

STORING:

Tool must be well cleaned and lightly lubricated before storing.

Store air tool in a dry safe place, out of the reach of children.

14

WARRANTY

This tool is warranted by the manufacturer to the original purchaser from the original

purchase date for three (3) years subject to the warranty coverage described herein.

This tool is warranted to the original user to be free from defect in material and

workmanship. If you believe that a tool is defective, return the tool, with proper proof

of purchase to the point of purchase. If it is determined that the tool is defective and

covered by this warranty, the distributor will replace the tool or refund the

purchase price.

This warranty is void if: defects in materials or workmanship or damages result from

repairs or alterations which have been made or attempted by others or the

unauthorized use of nonconforming parts; the damage is due to normal wear, damage

is due to abuse (including overloading of the tool beyond capacity), improper

maintenance, neglect or accident; or the damage is due to the use of the tool after

partial failure or use with improper accessories or unauthorized repair or alteration.

This warranty gives you specific legal rights, and you may also have other rights that

vary from state to state.

For warranty questions, call our customer service department at 1-888-3KOBALT,

8:00 a.m.-8:00 p.m. EST, Monday-Friday.

TROUBLESHOOTING

PROBLEM CORRECTIVE ACTIONPOSSIBLE CAUSE

Tool runs

slowly or will

not operate

6. Worn rotor blade.

7. Moisture blowing

out of tool exhaust.

6. Replace rotor blade.

7. Water in tank; drain tank. (See air

compressor manual). Oil tool and run

until no water is evident. Oil tool again

and run 1-2 seconds.

EXPLODED VIEW

Printed in China

15

C

E-ring

Washer

Bearing

Screw

Eccentric shaft

Screw M5x25

Screw M5x15

Spring washer

Front cover

Gasket

Nut M6

Inertia nut

Copper bush

Washer

Screw M6x33

Work spindle

Semi-round key

Bearing

Cylinder cover

Rotor blade

Rotor

Cylinder

E-ring 8

Housing

Housing cover

Bearing seat

Sanding pad

B

3

4

5

6

7

8

9

10

11

12

13

D

15

16

17

18

19

20

21

22

23

24

25

26

27

28

1

4

1

2

5

1

Part No.

Description

Qty.

29

30

31

32

33

34

E

36

37

38

G

40

41

42

43

44

45

46

47

48

49

F

52

51

53

Top cover

Pin 3x7

O-ring 7.5x1.8

Soft grip

Air regulator

O-ring 4.5x1.8

Air regulating knob

Screw M4x8

Soft grip

O-ring 18x1.8

Air inlet

Spring

O-ring 4x2

Valve stem

O-ring 3.5x1.5

O-ring 8x1.5

Valve seat

Trigger seat

Washer

Nut M10

Trigger

Screw M4x35

Nut M4

O-ring 11.2x1.6

1

2

1

Part No.

Description

Qty.

B

19

20

21

22

23

30

31

37

38

40

41

42

43

44

45

46

F

51

49

48

47

G

53

52

34

33

E

36

32

24

25

22

21

26

27 28

13

D1516

17

18

29

C3

4

5

6

7

8

910

11

12

KOBALT

®

and the K Design

®

are registered

16

ARTICLE #0075988

MODÈLE #SGY-AIR135TZ

KOBALT

®

et le motif de K

®

sont des marques

de commerce déposées de LF, LLC. Tous droits

réservés.

JOIGNEZ VOTRE REÇU ICI

Numéro de série Date d'achat

Des questions, des problèmes, des pièces manquantes? Avant de

retourner l'article au détaillant, communiquez avec notre service à la

clientèle au 1 888 3KOBALT, entre 8 h et 20 h (HNE), du lundi au vendredi.

15,24 CM

PONCEUSE À

DOUBLE ACTION

TABLE DES MATIÈRES

17

Consignes de sécurité ....................................................................................... 18

Caractéristiques du produit ................................................................................ 18

Contenu de l'emballage ..................................................................................... 24

Préparation ........................................................................................................ 24

Instructions pour l'assemblage .......................................................................... 25

Mode d'emploi ....................................... ............................................................ 27

Entretien ............................................................................................................ 28

Dépannage ........................................................................................................ 28

Garantie .............................................................................................................

29

Vues éclatées ....................................................................................................

30

de maintenir un niveau adéquat.

IMPORTANT : Cet outil nécessite un débit d'air d'au moins 5 pi par minute à une pression de

3

aux exigencies minimales (pi /min et lb/psi ). L'utilisation d'un tuyau à air peut entraîner une chute

2

90 lb/psi . Vérifiez les spécifications de votre compresseur d'air afin de vous assurer qu'il satisfait

2

de pression de jusqu'à 15 lb/psi . Il peut donc s'avérer nécessaire d'augmenter la pression afin

2

18

CONSIGNES DE SÉCURITÉ

Veuillez vous assurer de lire et de comprendre l'intégralité du présent guide avant

d'assembler, d'utiliser ou d'installer ce produit. Si vous avez des questions concernant

ce produit, veuillez téléphoner au service à la clientèle au 1 888 3KOBALT, entre 8 h et

20 h (HNE), du lundi au vendredi.

Une utilisation ou un entretien inadéquat de ce produit peut causer des blessures

graves ou des dommages matériels. Assurez-vous de lire et de comprendre tous

les avertissements et toutes les instructions concernant ce produit avant de l'utiliser.

Lorsque vous utilisez un outil pneumatique, observez toujours les mesures de

sécurité de base afin de réduire les risques de blessure.

AVERTISSEMENT

LA POUSSIÈRE CRÉÉE PENDANT LE PONÇAGE, LE SCIAGE, LE POLISSAGE, LE

PERÇAGE ET D'AUTRES ACTIVITÉS PEUT CONTENIR DES PRODUITS CHIMIQUES

RECONNUS PAR L'ÉTAT DE LA CALIFORNIE COMME ÉTANT LA CAUSE DE CANCERS,

D'ANOMALIES CONGÉNITALES ET D'AUTRES PROBLÈMES LIÉS AUX FONCTIONS

AU www.oehha.ca.gov, CONFORMÉMENT À LA PROPOSITION 65. VOICI

QUELQUES-UNS DE CES PRODUITS CHIMIQUES :

DU PLOMB PROVENANT DE PEINTURES À BASE DE PLOMB;

DE LA SILICE CRISTALLINE PROVENANT DE LA BRIQUE, DU CIMENT OU

D'AUTRES MATÉRIAUX DE MAÇONNERIE;

DE L'ARSENIC ET DU CHROME PROVENANT DU BOIS D'ŒUVRE TRAITÉ AVEC

UN PRODUIT CHIMIQUE.

REPRODUCTRICES. VOUS POUVEZ OBTENIR LA LISTE DES PRODUITS CHIMIQUES

LES RISQUES LIÉS À L’EXPOSITION À CES PRODUITS VARIENT SELON LE NOMBRE

DE FOIS OÙ VOUS PRATIQUEZ CES ACTIVITÉS. AFIN DE LIMITER VOTRE

EXPOSITION À CES PRODUITS CHIMIQUES, TRAVAILLEZ DANS UN ENDROIT BIEN

VENTILÉ ET UTILISEZ DE L’ÉQUIPEMENT DE SÉCURITÉ APPROUVÉ, TEL QU’UN

APPAREIL RESPIRATOIRE OU UN MASQUE ANTIPOUSSIÈRE CONÇUS

SPÉCIALEMENT POUR FILTRER LES PARTICULES MICROSCOPIQUES.

CARACTÉRISTIQUES

6 po

10 000 tours/minute +/- 10 %

3

5 pi /min

Filetage NPT 1/4 po

3/8 po

2

90 lb/p o

COMPOSANTE

TAMPON DE PONÇAGE

VITESSE LIBRE

CONSOMMATION D'AIR MOYENNE

ENTRÉE D'AIR

TUYAU À AIR

PRESSION DE SERVICE

CARACTÉRISTIQUES DU PRODUIT

19

Cet outil pneumatique peut projeter des

fixations, des fragments de métal, des

sciures de bois et d’autres débris, ce qui

peut causer des blessures graves.

L’air comprimé peut être dangereux, car

il est susceptible de projeter des objets

et des particules pouvant causer des

blessures aux tissus mous du corps,

notamment les yeux et les oreilles. Les

débris et les objets propulsés par le jet

d’air peuvent causer des blessures.

Ne laissez jamais un outil en marche

sans supervision. Débranchez le tuyau

à air lorsque vous n’utilisez pas l’outil et

placez-le dans un endroit sécuritaire.

Assurez-vous que les accessoires sont

bien fixés et assemblés avant d’utiliser

l’article.

Utilisez toujours l’outil à une distance

sécuritaire des autres personnes présentes

dans l’aire de travail et assurez-vous que

l’aire de travail est sécuritaire en tout temps.

CONSIGNES DE SÉCURITÉ

conformes à la norme ANSI Z87.1 et

pourvues d'écrans latéraux.

Portez toujours des lunettes de sécurité

desserrer ou se briser et être projetés

en direction de l'utilisateur ou d'autres

personnes présentes dans l'aire de travail.

Les accessoires de l'outil peuvent se

facial approuvé en plus de lunettes de

sécurité.

Pour plus de protection, utilisez un écran

Une ponceuse à double action peut

produire des étincelles susceptibles

d’enflammer certains matériaux.

RISQUES D'INCENDIE OU

D'EXPLOSION

AVERTISSEMENT

RISQUE MESURES PRÉVENTIVES

N'utilisez jamais un outil à proximité

d'une substance inflammable comme

de l'essence, du naphta, des solvants

de nettoyage, etc.

Travaillez dans un endroit propre, bien

ventilé et dépourvu de matériaux

combustibles.

N'utilisez jamais d'oxygène, de dioxyde

de carbone ni d'autre gaz embouteillé

comme source d'alimentation pour les

outils pneumatiques.

RISQUE DE PERTE AUDITIVE

Portez toujours des protecteurs auditifs

conformes à la norme ANSI S3.19.

Une exposition prolongée au bruit

produit par l'utilisation d'outils

pneumatiques peut entraîner une perte

auditive permanente.

AVERTISSEMENT

RISQUE MESURES PRÉVENTIVES

RISQUES DE BLESSURE AUX

YEUX OU À LA TÊTE

RISQUE MESURES PRÉVENTIVES

AVERTISSEMENT

20

Les outils qui contiennent ou déplacent

des pièces mobiles, par exemple les

douilles à choc, peuvent s'emmêler

dans les cheveux, les bijoux ou les

vêtements amples et causer des

blessures graves.

AVERTISSEMENT

RISQUE MESURES PRÉVENTIVES

RISQUE D'EMMÊLEMENT

Ne portez pas de vêtements amples, de

bijoux ni tout autre article qui pourrait

s’accrocher ou s’emmêler dans l’outil

lors de son utilisation.

Retirez tout bijou susceptible de

s’accrocher dans l’outil.

Gardez toujours vos mains et les autres

parties de votre corps à distance des

pièces en mouvement.

Portez toujours un respirateur ou un

écran facial bien ajusté lorsque vous

utilisez ce genre d'outils.

CONSIGNES DE SÉCURITÉ

Prenez garde à vos mains lorsque vous

utilisez l'outil.

Une ponceuse à double action peut causer

des blessures graves si elle n’est pas

utilisée adéquatement ou si elle est utilisée

d’une manière autre que celle pour laquelle

elle est conçue.

RISQUE DE COUPURE

OU DE BRÛLURE

AVERTISSEMENT

RISQUE MESURES PRÉVENTIVES

L'utilisation d'un outil pneumatique pour

fixer des fils électriques peut causer des

chocs électriques potentiellement mortels.

La poignée de cet outil n'est pas isolée.

Lorsque l'outil entre en contact avec un fil

sous tension, ses parties métalliques

exposées peuvent causer des chocs

électriques potentiellement mortels.

Le contact d'accessoires comme les

douilles à choc avec des fils électriques

dissimulés peut causer des chocs

électriques potentiellement mortels.

Ne fixez jamais des fils sous tension à

l'aide d'outils.

Évitez de toucher à des surfaces mises

à la terre, par exemple un tuyau, un

radiateur, une cuisinière ou un

réfrigérateur. Le contact de votre corps

avec une surface mise à la terre

augmente les risques de choc électrique.

Avant de commencer à travailler, vérifiez

soigneusement la surface pour déceler

les fils dissimulés.

RISQUE DE CHOC ÉLECTRIQUE

AVERTISSEMENT

RISQUE MESURES PRÉVENTIVES

La page charge ...

Kobalt SGY-AIR135TZ Manuel utilisateur

Ce manuel convient également à

Kobalt SGY-AIR135TZ Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents