IRIS 690400 Manuel utilisateur

IRIS
Marque
IRIS
Modèle
690400
Taper
Manuel utilisateur
key features
Hall Eect Sensor
The Iris Contact Sensor features a Hall eect sensor for increased sensitivity,
reliability, and reduced size. By eliminating the need for a reed switch, the
Hall eect sensor has no moving parts, increasing reliability. This feature also
increases the battery life of the sensor.
Easy Mounting Options
The Iris Contact Sensor can be installed using either adhesive strips or mount-
ing screws (both included).
Remove-to-Pair Join Process
All 3-Series sensors feature “Remove to Pair” joining. The device ships with
the battery pre-installed and all that is needed to begin the joining process is to
pull out a small plastic tab from the bottom of the device. There is nothing for
the user to take apart or put back together.
Reports Temperature:
Use the contact sensor to receive alerts when the temperature rises or falls to
user-defined levels.
Superior Output Power & Over-the-Air Updates:
The Contact Sensor supports over-the-air updates providing for seamless up-
grades and feature additions without the need for any user interaction.
getting started
Step 1
In the Iris by Lowe’s App, select the + sign then “Devices.”
Step 2
Remove the battery tab labeled “Remove to Pair”. The hub will beep
when pairing is complete.
CONTACT SENSOR
Iris Contact Sensor alerts you when doors, windows, cabinets and
more are opened or closed, and senses temperature to help you
monitor your home.
lowe’s item #
690400
model
3320-L
user guide: iris contact sensor (3320-l) © 2015 lowe’s iris. all rights reserved.1 / 2
front
2.5”
51 mm
0.80”
20 mm
pairing
use case
• Receive alerts when doors/
windows open or close while
you’re away
• Trigger “welcome” or
“goodbye” Scenes
• Trigger alarm when doors or
windows unexpectedly open
• Automate lights in closets
and small rooms
compatibility
The Lowe’s IRIS Contact
Sensor is fully ZigBee HA 1.2
certified and will work with
other open ZigBee HA 1.2-
certified systems.
led
reset button
battery (cr2)
user guide: iris contact sensor (3320-l) 2015 lowe’s iris. all rights reserved.2 / 2
CONTACT SENSOR
model
3320-L
lowe’s item #
690400
troubleshooting
Step 1
Slide o the battery cover.
Remove battery and replace with
a new CR-2 battery.
Reassemble and test operation.
Step 2
Remove battery. Insert a pa-
per clip into the reset hole on
the side of the device. While
holding down the reset button,
reinsert battery to factory reset
the device. Repeat the “Getting
Started” steps to rejoin the Zig-
Bee network.
for additional help
Check out support.IrisByLowes.
com or call 1-855-469-IRIS (4747).
technical specifications
Power
Rated: 3V
Battery: CR-2 (1x)
Battery Life: Up to 2 years
Environmental
Operating Temperature: 0° to 40°C
Shipping/Storage
Temperature: -20° to 50°C
Humidity Range: 0 to 90% RH.
(non-condensing)
Approvals
Wireless RF Protocol
Protocol: ZigBee HA 1.2
TX Strength: +8 dBm
RF Channels: 16
Range: 130 ft. (40m) LOS
approvals (english)
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Conforms to FCC Part 15B
Contains FCC ID: T3L-SS011
IC: 12192A-SS011
Industry Canada licence-exempt RSS Standards. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including interfer-
ence that may cause undesired operation.
Under Industry Canada regulations, this radio trans mitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the equiv-
alent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
This equipment complies with FCC and IC radiation exposure limits set forth
for an uncontrolled environment. This equipment is in direct contact with
the body of the user under normal operating conditions. This transmitter
must not be co-located or operating in conjunction with any other antenna
or transmitter.
Changes or modifications not expressly approved by Lowes, Inc. could void
the user’s authority to operate the equipment.
For more information, visit IrisByLowes.com.
approvals (franÇais)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Conformément à la réglementation d’Industrie Canada, le présent émetteur
radio peut fonctionner avec une antenne d’un type et d’un gain maximal
(ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de
réduire les risques de brouillage radioélectrique à l’intention des autres utili-
sateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance
isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à
l’établissement d’une communication satisfaisante.
Pour plus d’informations, visitez IrisByLowes.com.
  • Page 1 1
  • Page 2 2

IRIS 690400 Manuel utilisateur

IRIS
Marque
IRIS
Modèle
690400
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents