Automate MTBWAND18-25 Le manuel du propriétaire

MTBWAND18-25
Automate
Marque
Automate
Modèle
MTBWAND18-25
Taper
Le manuel du propriétaire
Battery Wand Battery Pack
INSTRUCTION MANUAL
DISCREET DESIGN Small
profile allows for optimal
placement in reloaded
battery tube.
BATTERY HEALTH When using the
Automate Pulse 2 hub & app, your
battery status is indicated on shade
screen.
AUTOMATE | Battery Wand Battery Pack_MTBWAND1825_IM_v1.0
FEATURES:
• Replacement for Traditional Battery Wands that use disposable batteries
• Provides up to 500 up/down cycles on a single charge(depends on shade size & fabric
weight)
• Compatible with Automate Cord Lift, Venetian Tilt, 25 tubular DC motor
• Small profile allows for optimal placement in window pocket
• Battery health status reported in Automate Pulse App
This re-loadable battery tube uses eight long-lasting, readily available lithium AA
batteries (not included) to power your Automate Shades and blinds. All mounting clips
and hardware included.
2 | Automate™ Battery Wand Battery Pack | MTBWAND18-25 ROLLEASE ACMEDA
SAFETY INSTRUCTIONS
COMPLIANCE STATEMENT
WARNING: Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
WARNING: Important safety instructions to be read before installation and use.
Incorrect installation or use can lead to serious injury and will void manufacturer’s liability and warranty.
It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference.
• Do not expose to water, moisture, humid and damp environments or extreme temperatures.
• Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge should not be
allowed to use this product.
• Use or modification outside the scope of this instruction manual will void warranty.
• Installation and programming to be performed by a suitably qualified installer.
• Follow installation instructions.
• For use with motorized shading devices.
• Keep away from children.
• Frequently inspect for improper operation. Do not use if repair or adjustment is necessary.
• Keep clear when in operation.
• Replace battery with correctly specified type.
This device complies with Part 15 of the FCC Rules / Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To satisfy FCC / IC RF exposure requirements, a separation distance of
20 cm or more should be maintained
between the antenna of this device and persons during device
operation.
To ensure compliance, operations at closer than this distance is not
recommended.
Les antennes installées doivent être situées de facon à ce que la
population ne puisse y être exposée à une distance de moin de 20
cm. Installer les antennes de facon à ce que le personnel ne puisse
approcher à 20 cm ou moins de la position centrale de l’ antenne.
La FCC des éltats-unis stipule que cet appareil doit être en tout temps
éloigné d’au moins 20 cm des personnes pendant son functionnement.
Do not dispose of in general waste.
Please recycle batteries and damaged
electrical products appropriately.
ROLLEASE ACMEDA Automate™ Battery Wand Battery Pack | MTBWAND18-25 | 3
AA AA AA AA AA AA AA AA
1 INSTALLATION
No recharging or expensive specialty batteries required. The 12V Re-loadable Battery Tube from Automate
uses eight readily available AA Lithium batteries. When your shade needs fresh power, simply unscrew the cap
and replace the batteries. (Please properly dispose of used Lithium batteries.)
Screw
OR
Double Sided Tape
Double Sided Tape*
Installation Orientation
This product is intended for indoor
use only. Please keep out of reach of
children. Avoid damaging product by
dropping or using undo force. Do not
expose product to open flame, heat,
or moisture
Do not install Battery Wand Battery Pack where it will be
exposed to direct sun light
*Not supplied
WARNING
IMPORTANT
Replacement Process
1.1 Replace the AA Batteries
1.2 Attachment Methods
AA OLD
AA NEW
X8 X8
Option 1: Horizontal Option 2: Vertical
4 | Automate™ Battery Wand Battery Pack | MTBWAND18-25 ROLLEASE ACMEDA
1.3 Motor Connections
Motor Connection Cable
Cord Lift
MTDCRF-CL-0.6-50
Tilt Blinds
MTDCRF-TILT-1
Motors
MTDCRF25-1.1
Charging uses the 2 pin, non-locking “JST” style connector.
ROLLEASE ACMEDA | AUSTRALIA
110 Northcorp Boulevard,
Broadmeadows VIC 3047, AUS
T +61 3 9355 0100 | F +61 3 9355 0110
ROLLEASE ACMEDA | USA
Level 7 / 750 East Main Street
Stamford, CT 06902, USA
T +1 800 552 5100 | F +1 203 964 0513
ROLLEASE ACMEDA | EUROPE
Via Conca Del Naviglio 18,
Milan (Lombardia) Italy
T +39 02 8982 7317 | F +39 02 8982 7317
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Automate MTBWAND18-25 Le manuel du propriétaire

MTBWAND18-25
Automate
Marque
Automate
Modèle
MTBWAND18-25
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents