Automate Li-ion 3.0 35mm Motor Manuel utilisateur

Marque: Automate

Modèle: Li-ion 3.0 35mm Motor

Taper: Manuel utilisateur

Li-ion & DC Motor

MOTOR PROGRAMMING INSTRUCTIONS

SOFT STOP

SOLAR OPTION

FAVORITE

POSITION

SELECTABLE

SPEED

BATTERY

POWERED

USB CHARGE

(Only for Li-ion Motor)

ELECTRONIC

LIMIT

LEVEL CONTROL

BATTERY CHECK433 MHZ

BI-DIRECTIONAL

AUTOMATE 5V ZERO & WIREFREE V1.0_PRGM_JULY_2022

Fav Position

Live Feedback

Energy ecient

2 | Automate™ Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA

SAFETY INSTRUCTIONS

WARNING: Important safety instructions to be read before installation.

Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

WARNING: Important safety instructions to be read before installation and use.

It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference.

WARNING: Incorrect installation or use can lead to serious injury and will void manufacturer’s liability and warranty.

• Read and follow all installation and safety instructions.

• This manual is also available on the website.

• Do not expose to water, moisture, humid and damp

environments or extreme temperatures.

• Use or modification outside the scope of this instruction manual

will void warranty.

• This appliance can be used by children aged 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning the use of the

appliance in a safe way and understand the hazards involved.

Children should not play with the appliance. Cleaning and user

maintenance should not be performed by children without

supervision.

• Do not allow children to play with fixed controls. Keep appliance

and remote controls away from children.

• Assembly, installation and programming must be performed by

a suitably qualified installer.

• For use with motorized shading devices.

• Frequently inspect the installation for improper operation, signs

of wear, imbalance or damage to cables or springs. Do not use if

repair or adjustment is necessary.

• The appliance must be disconnected from its power source

during cleaning, maintenance or when replacing parts.

Maintenance and parts replacement should be performed by a

suitably qualified installer/technician.

• The A-weighted emission sound pressure level of the appliance

is less than or equal to 70dB(A).

• The appliance is for indoor use only.

• Disconnect the appliance from power or switch off automatic

controls when maintenance, such as window cleaning, is being

carried out in the vicinity.

• The appliance must be supplied only the safe, extra-low voltage

corresponding to the marking on the appliance.

• Keep clear of the appliance when in operation.

• There are no user serviceable parts or batteries inside the

appliance.

• Remote batteries should be replaced with the correctly specified

type only.

• The mass and dimensions of the driven part must be compatible

with the rated torque and rated operating time of the appliance.

• The driven part must be compatible with the rated torque and

operating time of the appliance as follows:

For 0.5Nm motor series (MT01-1320-069001 and similar):

Rated torque of 0.5Nm, rated operating time of 12 minutes and

minimum tube diameter of ø20mm.

For 1.1Nm motor series (MT01-1325-069002, MT01-1225-069002

and similar): Rated torque of 1.1Nm, rated operating time of 12

minutes and minimum tube diameter of ø25mm.

For 2.0Nm motor series (MT01-1328-069001, MT01-1228-069002

and similar): Rated torque of 2.0Nm, rated operating time of 12

minutes and minimum tube diameter of ø28mm.

• Fixed controls have to be clearly visible after installation.

• The appliance is intended to be installed at a height of at least

2.5m above the floor or any other accessible level surface.

• Before installing the appliance, remove any unnecessary cords

or components and disable any equipment not needed for

powered operation.

ROLLEASE ACMEDA Automate™ Programming Instructions | Li-ion & DC Motors | 3

COMPLIANCE STATEMENT

This device complies with Part 15 of the FCC Rules / Industry Canada

licence-exempt RSS standard(s). Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d’Industrie Canada

applicables aux appareils radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et

(2) l’utilisateur de l’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate

the equipment.

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

To satisfy FCC / IC RF exposure requirements, a separation distance of

20 cm or more should be maintained

between the antenna of this device and persons during device

operation.

To ensure compliance, operations at closer than this distance is not

recommended.

Les antennes installées doivent être situées de facon à ce que la

population ne puisse y être exposée à une distance de moin de 20

cm. Installer les antennes de facon à ce que le personnel ne puisse

approcher à 20 cm ou moins de la position centrale de l’ antenne.

La FCC des éltats-unis stipule que cet appareil doit être en tout temps

éloigné d’au moins 20 cm des personnes pendant son functionnement.

Do not dispose of in general waste.

Please recycle batteries and damaged

electrical products appropriately.

4 | Automate™ Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA

CONTENTS

1 ASSEMBLY 5

2 RETROFIT INSTALLATION 6

3 CHARGING/POWER SUPPLY 6

4 P1 BUTTON FUNCTIONS 7

4.1 Motor state test 7

4.2 Motor configuration options 7

5 INITIAL SET UP 8

5.1 Pair motor with controller 8

5.2 Check motor direction 8

5.3 Set Limits 9

6 ADJUSTING LIMITS 10

6.1 Adjust upper limit 10

6.2 Adjust lower limit 10

7 CONTROLLERS AND CHANNELS 11

7.1 Using P2 Button on existing controller to add a

new controller or channel 11

7.2 Using a pre-existing controller to add or delete

a controller or channel 11

8 FAVORITE POSITIONING 12

8.1 Set a favorite position 12

8.2 Send shade to favorite position 12

8.3 Delete favorite position 12

9 TILT & ROLLER MODE 13

9.1 Toggle motor to Tilt Mode 13

9.2 Toggle Motor to Roller Mode 13

10 ADJUSTING SPEED 14

10.1 Increase Motor Speed 14

10.2 Decrease Motor Speed 14

11 SOFT STOP CONFIGURATION 15

11.1 Turn Soft Stop OFF 15

11.2 Turn Soft Stop ON 15

12 BATTERY CHECK FUNCTION 16

12.1 Send Shade to battery charge level 16

13 CHARGING LED 16

13.1 Turn Charging LED ON/OFF 16

14 SLEEP MODE 17

15 TROUBLE SHOOTING 18

16 NOTES 20

ROLLEASE ACMEDA Automate™ Programming Instructions | Li-ion & DC Motors | 5

1 ASSEMBLY

ZERO HEAD ADAPTER

ZERO HEAD ANTENNA WRAP

GENERIC CROWN, DRIVE & TUBE ASSEMBLY

6 | Automate™ Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA

3 CHARGING/POWER SUPPLY

2 RETROFIT INSTALLATION

(1.1Nm & 2.0Nm MOTOR ONLY)

(LI-ION 1.1Nm & 2.0Nm ONLY) (LI-ION 3.0Nm & 10.0Nm ONLY) (DC 1.1Nm & 2.0Nm ONLY)

Requries a continuous 12V DC Power Source.

ROLLEASE ACMEDA Automate™ Programming Instructions | Li-ion & DC Motors | 7

4.1 Motor state test

4.2 Motor configuration options

This table describes the function of a short P1 Button press/release (<2 seconds) depending on current motor

configuration.

The P1 Button is utilized to administer motor configurations as described below.

Activate Pairing Mode

Approx.

Sleep Mode

Reverse Direction

Approx.

Reset To Factory Settings

Approx.

4 P1 BUTTON FUNCTIONS

Press Condition Function

Achieved

Visual

Feedback

Audible

Feedback Function Described

Short

Press

If limit is NOT set None No Action None No Action

If limits are set

Operational

control of motor,

run to limit. Stop

if running

Motor Runs None

Operational control

of motor after pairing

and limit setting is

completed first time

If motor is in

“Sleep Mode” &

limits are set

Wake and control

Motor wakes

and runs in a

direction

None

Motor is restored from

Sleep Mode and RF

control is active

Hold P1 button on motor head.

P1 button on motor head.

Approx.

8 | Automate™ Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA

5.1 Pair motor with controller

5.2 Check motor direction

Consult user manual for your

controller for information on

selecting channel.

Damage to shade may occur when operating motor prior to

setting limits. Attention should be given.

Reversing motor direction using this method is only possible

during initial set-up

Hold P1 button on

motor head.

To check travel direction of shade, press UP or

DOWN on controller.

Quick Press = Step

Long Press = Continuous Travel

To reverse shade direction, hold both UP and

DOWN.

Until the motor responds.

Select channel on

controller.

Hold STOP on

controller.

Approx.

Motor Response

Motor is now in step mode and ready for setting limits

IMPORTANT

5 INITIAL SET UP

ROLLEASE ACMEDA Automate™ Programming Instructions | Li-ion & DC Motors | 9

SEC

Cycle shade up and down prior to setting limits to settle fabric

After setting limits, motor will automatically exit from initial

set-up mode.

Move shade to the desired highest or lowest

position by pressing the UP or DOWN buttons

on controller.

Move shade to the desired highest or lowest

position by pressing the UP or DOWN buttons

on controller.

To save upper limit, hold UP and STOP.

To save lower limit, hold DOWN and STOP.

Motor Response

IMPORTANT

Approx.

5.3 Set Limits

10 | Automate™ Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA

SEC

Hold UP and STOP on

controller.

Hold DOWN and STOP

on controller.

Move shade to the desired

lowest position by pressing

the UP or DOWN button.

Move shade to the desired

highest position by pressing

the UP or DOWN button.

To save upper limit, hold UP

and STOP.

To save lower limit, hold

DOWN and STOP.

Approx.

Motor Response

Motor Response Motor Response

Motor Response

6 ADJUSTING LIMITS

SEC SECS S

5 5

Approx. Approx.

The bottom limit should be set ~ 1.38 in. (35mm) below the Ultra-Lock to disengage the auto lock mechanism when the shade is raised.

IMPORTANT

6.1 Adjust upper limit

6.2 Adjust lower limit

ROLLEASE ACMEDA Automate™ Programming Instructions | Li-ion & DC Motors | 11

A = Existing controller or channel (to keep)

B = Controller or channel to add or remove

A = Existing controller or channel (to keep)

B = Controller or channel to add or remove

Press P2 on

controller A.

Press P2 on

controller A.

Press P2 on

controller A.

Press P2 on

controller A.

Press P2 on the

controller B to remove

it.

Press STOP on an new

controller to add it.

Motor Response

7 CONTROLLERS AND CHANNELS

Consult user manual for your controller or sensor

IMPORTANT

7.1 Using P2 Button on existing controller to add a new controller or channel

7.2 Using a pre-existing controller to add or delete a controller or channel

12 | Automate™ Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA

Press P2 on controller. Press STOP on controller. Press STOP on controller.

Move shade to the desired position by pressing the UP or DOWN button on the controller.

Press P2 on controller. Press STOP on controller. Press STOP on controller.

Approx.

Motor Response

8 FAVORITE POSITIONING

8.1 Set a favorite position

8.2 Send shade to favorite position

8.3 Delete favorite position

ROLLEASE ACMEDA Automate™ Programming Instructions | Li-ion & DC Motors | 13

9 TILT & ROLLER MODE

Press STOP on controller.

Hold UP & DOWN on controller.

Press STOP on controller.

Motor Response

Default motor mode is Roller after initial Limits have been set, use following steps to change to Roller Mode.

If motor is in Tilt Mode, use following steps to change to Roller Mode.

SEC

Approx.

9.1 Toggle motor to Tilt Mode

9.2 Toggle Motor to Roller Mode

14 | Automate™ Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA

10 ADJUSTING SPEED

Press P2 Press DOWN Press DOWN

Motor Response Motor Response Motor Response

Press P2 Press UP Press UP

Motor Response Motor Response Motor Response

Default motor mode is the slowest speed.

10.1 Increase Motor Speed

10.2 Decrease Motor Speed

ROLLEASE ACMEDA Automate™ Programming Instructions | Li-ion & DC Motors | 15

11 SOFT STOP CONFIGURATION

Press P2 Press DOWN Press DOWN

Motor Response Motor Response Motor Response

Press P2 Press UP Press UP

Motor Response Motor Response Motor Response

Motor must be in slowest speed to turn Soft Stop OFF.

Motor must be in fastest speed to turn Soft Stop ON.

11.1 Turn Soft Stop OFF

11.2 Turn Soft Stop ON

16 | Automate™ Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA

12 BATTERY CHECK FUNCTION

Hold UP

Motor Response Shade must be at Upper Limit

Hold UP for Approx. 5s

Shade must be at Upper Limit.

Shade moves to percentage of

battery charge remaining

SEC

Approx.

13 CHARGING LED

Hold DOWN to toggle off

Red LED flashes x3 Red LED flashes x3

Hold DOWN to toggle on

Motor Response Motor Response

SEC SEC

5 5

Approx. Approx.

Motor must be at Lower Limit.

Motor is fully charged

Motor is charging. Battery is

greater than 50%.

Motor is charging. Battery is

lower than 50%.

Upper Limit Percentage of

Battery Charge

Remaining

Percentage Depleted

Lower Limit

12.1 Send Shade to battery charge level

13.1 Turn Charging LED ON/OFF

(ONLY FOR LI-ION MOTORS)

SOLID GREEN

BLINKING GREEN

BLINKING GREEN & RED

CHARGING LED STATUS

NOTE: This feature is can only be used with a DC motor when it is using a Barrery Pack as its power source.

ROLLEASE ACMEDA Automate™ Programming Instructions | Li-ion & DC Motors | 17

9 SLEEP MODE

Enter Sleep Mode

Sleep mode is utilized to

prevent a motor from incorrect

configuration during other

motor setup.

Hold P1 button on the motor

head

If multiple motors are grouped on a single channel, Sleep Mode may be used to put all but 1 motor to sleep,

allowing programming of just the one motor that remains “Awake”. See page 6 for detailed P1 functions.

Exit Sleep Mode: Method 1

Exit sleep mode once the shade

is ready.

Press and release P1 button on

the motor head

Exit Sleep Mode: Method 2

Remove power and then

re-power the motor.

Motor Response Motor Response

14 SLEEP MODE

Approx.

18 | Automate™ Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA

ROLLEASE ACMEDA | AUSTRALIA

110 Northcorp Boulevard,

Broadmeadows VIC 3047, AUS

T +61 3 9355 0100 | F +61 3 9355 0110

ROLLEASE ACMEDA | USA

Level 7 / 750 East Main Street

Stamford, CT 06902, USA

T +1 800 552 5100 | F +1 203 964 0513

ROLLEASE ACMEDA | EUROPE

Via Conca Del Naviglio 18,

Milan (Lombardia) Italy

T +39 02 8982 7317 | F +39 02 8982 7317

15 TROUBLE SHOOTING

Problem Cause Remedy

Motor is not responding Battery in motor is depleted or

Power Supply is not working

Recharge with a compatible

charger

Insufficient charging from solar

PV panel

Check connection and orientation

of PV panel

Transmitter battery is discharged Replace battery

Battery is inserted incorrectly

into transmitter

Check battery polarity

Radio interference/shielding Ensure transmitter is positioned

away from metal objects and

the aerial on motor or receiver

is kept straight and away from

metal

Receiver distance is too far from

transmitter

Move transmitter to a closer

position

Charging failure Check power supply to motor is

connected and active

Motor beeps x10 when in use Battery voltage is low Recharge with a compatible

charger

Cannot program a single motor

(multiple motors respond)

Multiple motors are paired to the

same channel

Always reserve an individual

channel for programming

functions. Use Sleep Mode to

program individual motors.

automateshades.com

ROLLEASE ACMEDA Automate™ Programming Instructions | Li-ion & DC Motors | 19

16 NOTES

20 | Automate™ Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA

16 NOTES

Automate Li-ion 3.0 35mm Motor Manuel utilisateur

Marque: Automate

Modèle: Li-ion 3.0 35mm Motor

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Automate Li-ion 3.0 35mm Motor User manual

Automate Li-ion 3.0 35mm Motor Manuel utilisateur

Automate Li-ion 3.0 35mm Motor Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents