ZyXEL NBG-420N Le manuel du propriétaire

NBG420N

Wireless N Router

Quick Start Guide

Version 3.60

3/2008

Edition 1

DEFAULT LOGIN

IP Address http://192.168.1.1

Password 1234

CONTENTS

ENGLISH 2

DEUTSCH 16

ESPAÑOL 30

FRANÇAIS 44

ITALIANO 58

SVENSKA 72

ENGLISH

2

Overview

The NBG420N is an IEEE 802.11b/g/n wireless broadband router or access point (AP). As

a router, the NBG420N directs traffic between your wireless network and another network

such as the Internet as shown below, providing services such as content filtering,

bandwidth management and a firewall.

This Quick Start Guide shows you how to do the following with your NBG420N in router

mode:

1 Connecting Your Hardware

2 Accessing the Web Configurator

3 Connecting to the Internet with the Wizard

4 Set Up a Wireless Network Manually or with WPS

See your User’s Guide on the CD in the package on how to set up the NBG420N as an AP

and for more information on all features.

To read the User’s Guide insert the CD that came in the box into your CD-ROM drive. A

screen should pop up. Navigate to the User’s Guide from this screen. If a screen does not

pop up, open Windows Explorer (click My Computer), click on the CD-ROM drive (usually

drive D:) and navigate to it from there.

ENGLISH

3

1 Hardware Connections

Do the following to make hardware connections for initial setup.

Antennas:

Connect each antenna to an antenna socket, ensuring the antennas are screwed

in firmly and angled upwards.

WAN

Connect the WAN port on your NBG420N to the Ethernet port on the device with

which you are accessing the Internet (for example, a router or modem) using an

Ethernet cable.

LAN

Connect the Ethernet port on your computer to a LAN port on the NBG420N using

the included Ethernet cable.

POWER Connection

Use the power adapter from the package to connect the POWER socket to an

appropriate power source.

Internet

4

2

3

1

2

3

4

ENGLISH

4

The LEDs

Look at the LEDs (lights). When you connect the power, the power LED ( ) blinks and

stays on once the device is ready.

The LAN ( ) and WAN ( ) LEDs turn on if the corresponding connections

are properly made.

V If an LED does not turn on, check your connections. If this doesn’t help,

disconnect the NBG420N from its power source, wait for a few seconds and

turn it back on.

2 Accessing the Web Configurator

Default Login Information

1 Launch an Internet browser such as Internet Explorer. Enter “http://192.168.1.1” as

shown below.

IP address http://192.168.1.1

administrator password 1234

ENGLISH

5

2 The Password window displays. Enter the password (“1234” is the default) and click

Login.

V If the login screen does not display, make sure your computer is set to

receive an IP address dynamically. If that doesn’t help, check your web

browser’s security settings (see the appendix in the User’s Guide for

information on both suggestions).

3 Change the password in the screen that follows and click Apply.

4 Click Go to Wizard setup to set up your NBG420N for the first time

3 Connection Wizard Setup

1 Select a language. Click Next.

ENGLISH

6

2 Click Next in the following screen to proceed with the Connection Wizard.

" Enter the Internet access information exactly as given to you by your ISP in

each wizard screen. Click Next to continue or click Back to return to the

previous screen. Current screen information will be lost if you click Back.

3.1 System Information

This screen is optional. You can just click Next.

3.2 Wireless LAN

Configure your NBG420N to support a wireless network by following these steps.

1 Enter a unique Name (SSID) to identify the NBG420N on the wireless LAN.

2 Select Auto to automatically use WPA-PSK which provides a high level of security. See

your User’s Guide for information on other kinds of security. Click Next.

ENGLISH

7

3 Write down the security key that displays in the pop-up screen. Computers on the wireless

network will need this security key to access the NBG420N. The security key is case-

sensitive so “ABCD” is not the same as “abcd”.

" Write down the security key, Name (SSID), Security and Channel

Selection for later use as the NBG420N and other devices on your wireless

network must use the same settings.

4 Click OK to continue.

3.3 WAN Connection

You may need to wait several minutes while the wizard attempts to detect which WAN

connection type (Ethernet, PPP over Ethernet or PPTP) you are using.

• If the wizard detects your connection type, follow the steps for your connection type as

given below.

• If the wizard cannot detect a connection type, you must select your connection type from

the drop-down list box in the screen below. If you do not know what connection type to use,

check with your Internet Service Provider (ISP).

" If you were given Internet access settings, type them in the following fields.

Otherwise leave the default settings and click Next.

ENGLISH

8

Ethernet Connection

Select Ethernet as your WAN connection type and click Next to go to section 3.4.

PPP over Ethernet Connection

1 Select PPP over Ethernet as your WAN connection type

2 Type a Service Name (if your ISP gave you one), User Name and Password. Click Next

to go to section 3.4.

PPTP Connection

1 Select PPTP as your WAN connection type.

2 Type a User Name and Password.

3 Type a PPTP Server IP Address.

4 Type a Connection ID/Name (if provided by your ISP).

5 If your ISP did not assign you a fixed PPTP IP address, select Get automatically from

ISP.

6 If your ISP assigned you a fixed PPTP IP address, select Use fixed IP address to give

the NBG420N a fixed, unique PPTP IP address and subnet mask.

ENGLISH

9

7 Click Next to go to section 3.4.

3.4 WAN IP Address

• If your ISP did not assign you a fixed IP address, select Get automatically from your ISP

and click Next to go to section 3.5.

• If your ISP gave you a fixed IP address:

1 Select Use fixed IP address provided by your ISP. Click Next.

2 In the next screen type the WAN IP address, WAN IP Subnet Mask and the gateway IP

address given by your ISP.

If you were given DNS server settings, type them in the fields. Otherwise leave the default

settings and click Next.

3.5 WAN MAC Address

A MAC address is a number which uniquely identifies a device on any network. Set the

WAN port’s MAC address by either using your device’s factory assigned default MAC

address or cloning the MAC address of a computer on your LAN. By default, the NBG420N

uses the factory assigned MAC address to identify itself on the WAN.

ENGLISH

10

•Select Factory Default to use the factory-assigned, default MAC address.

•Select Clone the Computer’s MAC Address to clone the MAC address from a computer

on your LAN. Type the IP address of the computer with the MAC address you are cloning. It

is advisable to clone the MAC address from a computer on your LAN even if your ISP does

not presently require MAC address authentication.

•Select Set WAN MAC Address if you know the MAC address you want to use.

3.6 Bandwidth Management

Select Enable BM for all traffic automatically to have the NBG420N prioritize data traffic

according to the its use. For example, video streaming may have higher priority than email.

Leave unchecked if unsure. Click Next.

3.7 Setup Complete

1 Click Apply to save your changes in the next screen that appears in the wizard.

2 Click Finish in the screen below to complete the wizard setup.

3 Congratulations. Open a web browser, such as Internet Explorer, to visit your favorite

website.

ENGLISH

11

V If you cannot access the Internet when your computer is connected to one

of the NBG420N’s LAN ports, check your connections. Then turn the

NBG420N off, wait for a few seconds and turn it back on. If this doesn’t

work run the wizard again, making sure you type the information correctly.

Also, if you are using a new Internet account, contact your ISP to make

sure it is active. See Troubleshooting in the User’s Guide for more

suggestions.

4 Set Up a Wireless Network

You can use Wi-Fi Protected Setup (WPS) to add wireless devices to your wireless

network. The other wireless devices must also support WPS.

If your wireless devices display the WPS logo as shown, go to

section 4.1 to use WPS to set up your wireless network.

If your wireless devices do not display the WPS logo, go to section

4.2 to manually set up a wireless network.

4.1 Set up Your Wireless Network with WPS

Follow these steps to set up your wireless network using WPS.

1 Place a WPS-enabled device within range of the NBG420N.

ENGLISH

12

2 Press the WPS button on both devices. It doesn’t matter which button is pressed first.

You must press the second button within two minutes of pressing the first one.

" Your NBG420N has a WPS button located on its housing, as well as a WPS

button available in the web configurator used to manage the NBG420N.

Other WPS-enabled devices should have at least one similar WPS button.

3 The WPS LED ( ) on the NBG420N blinks for a few seconds, then shines steadily.

4 Check if your devices are connected by trying to connect to the Internet using the

device you connected to the NBG420N. If you can do this, then your WPS connection is

successful.

5 To add another WPS enabled device to your wireless network, press the WPS buttons

on your NBG420N and your next WPS-enabled device.

Congratulations! You are now ready to connect to the Internet wirelessly through your

NBG420N.

2 minutes

ENGLISH

13

4.2 Set up a Wireless Network Manually

You can now connect wirelessly to your NBG420N from your computer and access the

Internet. You will need the Network Name (SSID) and also the Security Key (Pre-Shared

Key) if you set up security in the previous section. The connection procedure is shown

here using Windows XP as an example.

1 Right-click the wireless adapter icon which appears

in the bottom right of your computer monitor. Click

View Available Wireless Networks.

2 Select the SSID name you gave the

NBG420N and click Connect (A). The

SSID “SecureWirelessNetwork” is

given here as an example.

3 If you have set up wireless security,

you are prompted to enter a

password. Enter the Pre-Shared Key

you set up in the previous section

and click Connect (B).

4 You may have to wait several minutes

while your computer connects to the

wireless network.

5 You should now be securely connected wirelessly to the NBG420N.

Congratulations! You are now ready to connect to the Internet wirelessly

through your NBG420N.

A

B

ENGLISH

14

V If you cannot connect wirelessly to the NBG420N, check you have selected

the correct SSID and entered the correct security key. If that does not work,

ensure your network adapter is enabled by clicking on the wireless adapter

icon and clicking Enable. See the User’s Guide for more suggestions.

Procedure to View a Product’s Certification(s)

1 Go to www.zyxel.com.

2 Select your product from the drop-down list box on the ZyXEL home

page to go to that product's page.

3 Select the certification you wish to view from this page.

ENGLISH

15

DEUTSCH

16

Übersicht

Der NBG420N ist ein drahtloser IEEE 802.11b/g/n-Breitbandrouter und Access-Point (AP).

Als Router leitet der NBG420N den Datenverkehr zwischen dem Drahtlosnetzwerk und

einem anderen Netzwerk wie dem Internet wie unten dargestellt weiter und bietet Dienste

an wie Inhaltsfilter, Bandbreitenverwaltung und Firewall.

In dieser Kurzanleitung erfahren Sie, wie Sie Folgendes mit Ihrem NBG420N im Router-

Modus einrichten können:

1 Anschließen der Hardware

2 Zugreifen auf den Web-Konfigurator

3 Herstellen der Verbindung zum Internet mittels dem Assistenten

4 Manuelles Einrichten eines Drahtlosnetzwerks oder Einrichten mittels WPS Funktion

Weitere Informationen zu allen Funktionen, z. B., wie Sie den NBG420N als Access Point

(AP) verwenden, finden Sie im Benutzerhandbuch auf der CD.

Um das Benutzerhandbuch zu lesen, legen Sie die enthaltene CD in das CD-ROM-

Laufwerk Ihres Computers ein. Auf dem Bildschirm erscheint ein Fenster. Rufen Sie über

dieses Fenster das Benutzerhandbuch auf. Sollte dieses Fenster nicht angezeigt werden,

rufen Sie den Windows Explorer auf (klicken Sie auf Arbeitsplatz), klicken Sie auf das CD-

ROM-Laufwerk (normalerweise Laufwerksbezeichnung D:), und wählen Sie dann auf die

Datei des Benutzerhandbuchs.

DEUTSCH

17

1 Anschließen der Hardware

Bei der Erstinstallation müssen die folgenden Hardwareverbindungen hergestellt werden:

Antennen

Schließen Sie alle Antennen an den jeweiligen Antennenanschluss an. Stellen Sie

sicher, dass die Antennen fest eingedreht sind und aufrecht ausgerichtet sind.

WAN

Schließen Sie Ihr Modem mit dem mitgelieferten Kabel an den "WAN"-Anschluss

an.

LAN

Schließen Sie Ihren Computer mit dem mitgelieferten Ethernet-Kabel an einen

"LAN"-Anschluss an.

Anschließen an das Stromnetz

Schließen Sie das mitgelieferte Netzkabel an den POWER-Anschluss (Netzan-

schluss) und an eine geeignete Stromquelle an.

Internet

4

2

3

1

2

3

4

DEUTSCH

18

Die LED-Anzeigen

Das Gerät verfügt über LED-Anzeigen. Wenn Sie das Gerät an das Stromnetz

anschließen, beginnt die LED-Anzeige ( ) zu blinken. Wenn es bereit ist, hört sie auf zu

blinken und leuchtet stetig.

Die LED-Anzeigen LAN ( ) und WAN ( ) beginnen zu leuchten, wenn die

entsprechenden Verbindungen bestehen.

VSollte eine LED nicht leuchten, prüfen Sie die Verbindung. Leuchtet sie auch

dann nicht, trennen Sie den NBG420N von seiner Stromquelle, und schalten

Sie ihn einige Sekunden später wieder ein.

2 Zugriff auf den Web-Konfigurator

Standard-Anmeldeinformationen

1 Starten Sie einen Internet-Browser, z. B. Internet Explorer. Geben Sie wie unten

dargestellt “http://192.168.1.1” ein.

IP-Adresse http://192.168.1.1

Administratorkennwort 1234

DEUTSCH

19

2 Das Fenster Password (Kennwort) erscheint. Geben Sie das Kennwort ein ("1234" ist

das Standardkennwort), und klicken Sie auf Login (Anmelden).

V Wenn das Anmeldefenster nicht angezeigt wird, stellen Sie sicher, dass der

Computer so eingestellt ist, dass er eine dynamische IP-Adresse bezieht.

Wenn das Problem dadurch nicht behoben ist, prüfen Sie die

Sicherheitseinstellungen Ihres Webbrowsers (Informationen zu beiden

Möglichkeiten finden Sie im Anhang des Benutzerhandbuchs).

3 Ändern Sie im nachfolgenden Fenster das Kennwort und klicken Sie auf Apply

(Übernehmen).

4 Wenn Sie den NBG420N das erste Mal benutzen, klicken Sie auf Go Wizard setup

(Zum Einrichtungsassistenten).

DEUTSCH

20

3 Assistent zum Einrichten der Verbindung

1 Sprache wählen. Klicken Sie auf Next (Weiter).

2 Klicken Sie auf Next (Weiter) und fahren Sie mit dem Connection Wizard

(Verbindungsassistent) fort.

" Geben Sie die Daten für den Internetzugriff so ein, wie Sie sie von Ihrem

Internetdienstanbieter erhalten haben. Klicken Sie zum Fortfahren auf Next

(Weiter) oder auf Back (Zurück), um zum vorhergehenden Fenster

zurückzukehren. Wenn Sie auf Back (Zurück) klicken, gehen alle aktuell

auf dem Bildschirm vorhandenen Daten verloren.

3.1 Systeminformationen

Dieses Fenster ist optional. Sie können einfach auf Next (Weiter) klicken.

3.2 Wireless-LAN

Führen Sie die folgenden Schritte aus, um den NBG420N so zu konfigurieren, dass er ein

drahtloses Netzwerk unterstützt.

1 Geben Sie einen Namen (SSID) ein, mit dem der NBG420N im Wireless-LAN eindeutig

identifiziert wird.

La page charge ...

ZyXEL NBG-420N Le manuel du propriétaire

ZyXEL NBG-420N Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents