Best WCP3I30SB Guide d'installation

Marque: Best

Modèle: WCP3I30SB

Catégorie: Hottes

Taper: Guide d'installation

Ce manuel convient également à

WCP3I36SB

WCP3I SERIES

HB0311

INSTALLATION INSTRUCTIONS

INTENDED FOR DOMESTIC COOKING ONLY

INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.

HOMEOWNER: USE AND CARE INFORMATION ON PAGES 12 AND 13.

READ AND SAVE THESE INSTRUCTIONS

BEST; Hartford, Wisconsin www.BestRangeHoods.com 800-558-1711

BEST; Drummondville, QC, Canada www.BestRangeHoods.ca 866-737-7770

23863 rev. 03

! !

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by

qualified personnel in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer’s guidelines and safety standards such as

those published by the National Fire Protection Association

(NFPA) and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE) and the local code

authorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented outdoors.

7. Do not use this unit with any solid-state speed control device.

8. To reduce the risk of fire, use only metal ductwork.

9. This unit must be grounded.

10. When applicable, local regulations comprise more

restrictive installation and/or certification requirements,

the aforementioned requirements prevail on those of this

document and the installer agrees to conform to these at his

own expense.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers

cause smoking and greasy spillovers that may ignite. Heat oils

slowly on low or medium settings.

b) Always turn power hood ON when cooking at high heat or

when flambeing food (i.e.: Crêpes Suzette, Cherries Jubilee,

Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed

to accumulate on fan, filters or in exhaust ducts.

d) Use proper pan size. Always use cookware appropriate for the

size of the surface element.

1. For indoor use only.

2. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

3. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

4. Your hood motor has a thermal overload which will automatically

shut off the motor if it overheats. The motor will restart when it

cools down. If the motor continues to shut off and restart, have

the hood serviced.

5. The minimum hood distance above cooktop must not be

less than 24” (30” over a gas range). A maximum of 30”

above cooktop is recommended for best capture of cooking

impurities.

6. Two installers are recommended because of the large size and

weight of this unit.

7. To reduce the risk of fire and to properly exhaust air, be sure to

duct air outside — Do not exhaust air into spaces within walls

or ceiling or into attics, crawl space or garage.

8. Because of the high exhausting capacity of this hood, you

should make sure enough air is entering the house. Open a

window close to or in the kitchen.

9. To reduce the risk of fire and electrical shock, the Best WCP3I

Series models should only be installed with their own built-in

blowers.

10. When used in recirculation mode, to reduce the risk of fire and

shock, use only conversion kit model HRKBSS.

11. Please read specification label on product for further

information and requirements.

WARNING

CAUTION

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE

THE FOLLOWING*:

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or

metal tray, then turn off the burner. BE CAREFUL TO PREVENT

BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY,

EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN — You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels —

This could cause a violent steam explosion.

4. Use an extinguisher ONLY if:

A. You own a Class ABC extinguisher and you know how to

operate it.

B. The fire is small and contained in the area where it started.

C. The fire department has been called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

WARNING

1. PREPARE THE INSTALLATION

NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer.

Make sure that the following items are included:

- Hood

- Accessories • Decorative flue assembly (lower and upper flues)

• Hood mounting bracket

• Upper flue mounting bracket

• 2 hybrid filters

• 6” round adapter/damper (for vertical discharge), in a bag

• 3¼” x 10” adapter/damper (for horizontal or vertical discharge)

• Bag of parts including: 5 no. 8 x 1½” countersunk screws, 8 no. 8 x 3/4” screws, 6 no. 8 x 3/8” screws,

6 drywall anchors, 3 washers, 2 no. 8 x 1/2”, 2 neoprene pieces. If need be,

discard extra hardware.

Parts sold separately:

- Duct, elbows, wall or roof caps.

- Optional flue extension for 10-ft. ceilings model AEWCP3SB.

- Non-duct kit model HRKBSS, mandatory for non-ducted installation.

NOTE: The maximum ceiling height must not exceed 9 ft. when using a non-duct kit.

WARNING

When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.

2. SELECT INSTALLATION TYPE

NOTE: During the installation, protect countertop and/or cooktop.

2.1 NON-DUCTED INSTALLATION

The non-duct kit model HRKBSS is required for a non-ducted installation.

2.2 DUCTED INSTALLATION

Plan where and how the ductwork will be installed.

Install proper-sized ductwork, elbows and roof or wall cap depending on the type

of installation. For vertical discharge, use 6” round or 3¼” x 10” ductwork and for

horizontal discharge use 3¼” x 10” ductwork only. Use metal foil duct tape to seal duct

joints.

2.3 ALL INSTALLATIONS

The minimum hood distance above cooktop is 24” (30” over a gas range). A

maximum of 30” above cooktop is recommended for best capture of cooking

impurities.

Distances over 30” are at the installer and users discretion providing that ceiling

height and decorative flue length allow it.

HH0246A

3¼” X 10” DUCT

OR 6 ” ROUND DUCT

ROOF CAP

3¼” X 10” DUCT

WALL

HOOD

DECORATIVE

FLUE

REFER TO CHART

FOR

DISTANCE ABOVE

COOKING SURFACE

CEILING HEIGHT

MINIMUM HOOD DISTANCE ABOVE

ELECTRIC RANGE COOKTOP

MINIMUM HOOD DISTANCE

ABOVE GAS RANGE COOKTOP

8 FT. 24 IN. 30 IN.

FT. 28½ IN. 30 IN.

10 FT.* 28½ IN. 30 IN.

* 10-ft. ceilings require flue extension model AEWCP3SB (sold separately).

Before installation, remove and discard the shipping bracket (in grey) and its retaining

screws. See illustration on the right.

HD0937

SCREW LOCATIONS

2. SELECT INSTALLATION TYPE (CONT'D)

Refer to illustrations below to locate duct opening according to discharge type chosen (grey parts to be installed later).

3. REMOVE HYBRID GREASE FILTERS

Rest the range hood on a table. Remove tapes on filters. Remove filters from range hood by

pushing them down and tilt, then set aside the filters.

Remove both styrofoam pieces and tape from under the blower and discard.

3”

/8”

9¾”

HK0258A

/16”

30”

WIDTH HOOD

36” WIDTH HOOD

3¼”

15/16”

VERTICAL DISCHARGE

/8”

/16”

9¾”

HK0273A

/16”

30”

WIDTH HOOD

36” WIDTH HOOD

3¼”

HORIZONTAL DISCHARGE

HK0261A

/16”

30”

WIDTH HOOD

36” WIDTH HOOD

6” DIA.

VERTICAL DISCHARGE OR NON-DUCTED INSTALLATION

HD1099

5. BLOWER REMOVAL (HORIZONTAL DISCHARGE ONLY)

These range hoods are factory shipped with the blower mounted for a vertical discharge configuration. For a horizontal discharge

configuration, disassemble the blower from the inner top of the hood (see procedure below). It will be assembled to the inner back of the

hood once the hood is mounted on the wall.

FOR HORIZONTAL DISCHARGE:

From outside the unit, remove the knockout from back of hood (see illustration beside).

HR0123

4. CHOOSE THE OPENING

2) Using a 5/16” socket, or a Robertson or a Phillips no. 2 screwdriver,

remove the 4 blower mounting screws (2 on each side) from the inner

top of the hood. Set the blower and screws aside.

1) Unplug the blower.

HD0386

RIGHT SIDE MOUNTING

SCREW LOCATIONS

HD0385

LEFT SIDE MOUNTING

SCREW LOCATIONS

HE0234

FOR VERTICAL DISCHARGE OR NON-DUCTED INSTALLATION:

Remove the knockout in order to clear vertical discharge opening (see illustration beside).

HR0122

7. WIRING INSTALLATION

WARNING

Improper grounding can result in a risk of electric shock. Consult a qualified electrician if the grounding instructions

are not completely understood, or if there is any doubt as to whether the appliance is properly grounded. Do not

use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the

appliance, in accordance with all applicable codes and standards. Turn off electrical power at service entrance

before wiring.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an

escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must

be plugged into an outlet that is properly installed and grounded.

Position the outlet within the space covered by the decorative flue. Place the outlet at a

maximum distance of 24” (from where the cord exits from the hood). The center of the outlet

must be positioned at 3½”

from the center of the future hood location (as illustrated beside).

Make sure this does not interfere with a mounting bracket fastening area or with the decorative

flue (where the flue touches the wall).

HE0233A

Secure the adapter/damper to the back of the hood using 2 no. 8 x 3/8” screws

(included). Seal the adapter/damper to the hood using metal foil duct tape.

NOTE: The wall ducting must be properly prepared to receive the adapter. Before

performing the installation, make sure the adapter fits easily in the duct.

HJ0129

6. INSTALL ADAPTER/DAMPER (6” ROUND OR 3¼” X 10”)

Mount the 6” round adapter/damper (included in bag) using 4 no. 8 x 3/8” screws (included) or the 3¼” x 10” adapter/damper to the hood

using 2 no. 8 x 3/8” screws (included). Seal the adapter/damper to the hood using metal foil duct tape.

HJ0139

HJ0140

VERTICAL DISCHARGE 3¼” X 10”

ORIZONTAL DISCHARGE 3¼” X 10” ONLY

VERTICAL DISCHARGE 6” ROUND AND

NON-DUCTED INSTALLATION ONLY

8. INSTALL HOOD MOUNTING BRACKET

Construct wood wall framing that is even with the surface of wall studs.

Wood wall framing must be at least 1/2” thick and 3” high. Fasten wood wall

framing to wall studs for a solid installation.

Make sure that the height of the framing will allow the mounting bracket

to be secured to the framing within the dimensions shown (see illustration

beside).

After wall surface is finished, carefully center and level the hood

mounting bracket over installation location. Secure it to wall framing using

3 no. 8 x 1½” screws.

Using a level, draw a vertical line up to the ceiling starting from the

mounting bracket center.

9. INSTALL UPPER FLUE MOUNTING BRACKET (DUCTED INSTALLATION ONLY)

10. INSTALL THE HOOD

WARNING

When cutting or drilling into wall, do not damage electrical

wiring and other hidden utilities.

Center the upper flue mounting bracket with the center line previously

drawn in step 8 and place it flush with the ceiling.

Use the upper flue mounting bracket as a template to mark the position of

its screws.

Drill the 3 screw holes using a 3/16” drill bit.

Insert the included drywall anchors into the drilled holes (1 per hole).

Secure the upper flue bracket to the wall using 3 no. 8 x 3/4” screws.

Ensure that the bracket is tight against the wall.

CAUTION

DO NOT REMOVE the protective plastic film covering the decorative flue (upper & lower) yet.

1. Align the hood and center it above the hood mounting bracket. Gently lower the

hood until it securely engages the bracket.

2. Level the hood.

3. With the hood hanging in place, mark both hole locations on wall (2 embossed

holes on back of hood; see illustration at right).

4. Remove the hood.

5. Drill through both marked holes on wall using a 3/16” drill bit. Insert the included

drywall anchors into the drilled holes (one for each hole).

6. Hang the hood to the wall bracket.

7. Secure the hood to the wall using 2 no. 8 x 3/4” screws and 2 washers.

/8” = BOTTOM OF HOOD 24” ABOVE COOKTOP

/8” = BOTTOM OF HOOD 30” ABOVE COOKTOP

SCREW LOCATIONS

HD0377

CEILING

MOUNTING BRACKET

FLUSH WITH CEILING

WARNING

BE CAREFUL when installing the decorative flue and hood, they may have sharp edges.

HOLE LOCATIONS

Ø 3/16” TYP.

HD0810A

SIDE VIEW

HD0813A

WALL STUDS

FRAMING BEHIND DRYWALL

NOTE: ILLUSTRATION ABOVE REPRESENTS HORIZONTAL

EXHAUST CONFIGURATION, BUT IT ALSO APPLIES TO

ALL CONFIGURATIONS.

11. REINSTALL BLOWER (HORIZONTAL DISCHARGE ONLY)

1) Position the blower on the inner back of the hood, as shown on the right.

2) Using a 5/16” socket, or a Robertson or a Phillips no. 2 screwdriver and the 4 screws

previously removed, secure the blower to the hood.

NOTE: In order to ease installation, before mounting the blower, prepare the screw holes

by screwing all 4 screws without the blower, then remove and mount the blower.

3) Plug the blower connector back in and plug hood power cord into the outlet.

HD0829

RIGHT SIDE

MOUNTING

SCREW

LOCATIONS

12. PLENUM INSTALLATION (NON-DUCTED INSTALLATION ONLY)

HD1025

Using 4 no. 8 x 3/8” provided screws, assemble the 6” round adapter to the lower plenum plate.

HD1024

Remove the shipping tape retaining the lower and upper plenum plates with the 6” round adapter

together. Carefully align the upper plenum plate central notch with the line traced in step 8 (see

inset at right) and place it flush to the ceiling. Use the plate as a template to mark the position (A)

of its screws.

NOTE: To ease installation, there are many screw configurations: 6 in ceiling and 2 in wall, on each

side. Only 4 screws are needed to hold the top plenum plate.

Insert the included drywall anchors in the marked holes, then secure the upper plate using

4 no. 8 x 3/4” screws and washers (included with non-duct kit). Make sure the plate is tight against

the wall and ceiling.

HA0135

Assemble the lower plenum plate and 6” round adapter assembly to the upper plate by inserting

both tabs of the top plenum plate to their corresponding slots in lower plenum plate. Secure the

plenum assemby using 2 no. 8-18 x 3/8” screws (included).

HJ0142

HJ0141

13. DUCT CONNECTION (VERTICAL DISCHARGE AND NON-DUCTED INSTALLATION ONLY)

VERTICAL DISCHARGE:

Plug hood power cord into the outlet. Slide a 6” round or a 3¼” x 10” metal duct over the adapter/damper on the hood. Use metal foil duct

tape to seal the joint.

NON-DUCTED INSTALLATION:

Plug hood power cord into the outlet.

Slide a 6” round flexible metal duct (included) over the adapter/damper on the hood.

Use metal foil duct tape to seal the joint.

HJ0153

Stretch the flexible metal duct up to the plenum, over the adapter. Use metal foil duct tape

to seal the joint.

HJ0155

14. PREPARE DECORATIVE FLUE

HO0271

LOWER FLUE

REAR NOTCH

DUCTED INSTALLATION:

Remove protective plastic film covering the lower flue only.

Peel off both corners at the top of the upper flue (note that upper part has one hole on left and right

sides; see image on the right).

Position the lower flue rear notches down.

Gently slide upper flue inside lower flue.

Both lower and upper flues are included with the hood, but for a 10-foot ceiling, discard the provided

upper flue and use the optional flue extension model AEWCP3SB (sold separately).

HA0078

LOUVERS

NON-DUCTED INSTALLATION:

Remove protective plastic film covering the lower flue only.

NOTE: Do not use the upper decorative flue included with the hood.

Peel off the plastic film covering both top corners of the upper decorative flue (included with

the non-duct kit).

Position the lower flue rear notches down (the ones with the 45° angle).

Gently slide upper flue inside lower flue, louvers end up.

15. INSTALL DECORATIVE FLUE

ALL INSTALLATIONS:

Carefully slide in place decorative flue base (notches end first) in the groove

(shaded part in inset at right) behind the exterior wall of the top of the hood.

DUCTED INSTALLATIONS:

Slide up the upper flue until it is aligned with its mounting bracket. The bracket must be

inside the flue. Secure the upper flue to its bracket using 2 no. 8 x 3/8” screws (included).

See illustration beside.

NOTE: Duct not shown in illustration to ease understanding.

16. REINSTALL HYBRID FILTERS

HO0140

UPPER FLUE MOUNTING BRACKET

FRONT VIEW

UPPER

FLUE

Rest rear filters edge on filter springs in the range hood. Using finger cup, tilt up the filters into position.

Make sure both tabs (A) are securely engaged in range hood front edge slots after installation.

HO0272

HD1100

NON-DUCTED INSTALLATION:

Slide the upper flue up to the ceiling. The plenum must be inside the flue. Secure the upper

flue to the plenum sides using 2 no. 8 x 3/8” screws (included) per side for stainless steel

model or 2 no. 8 x 1/2” black screws (included) per side for black stainless model.

NOTE: Ceiling not shown in illustration to ease understanding.

HA0136

ALL INSTALLATIONS:

Remove protective plastic film covering the upper flue.

17. LIGHTING

WARNING

Do not touch lamps during or soon after operation. Burns may occur. Cannot be replaced by any other type of light

bulb or LED module.

The lighting of WCP3I Series range hood is produced by two LED modules (included).

18. CARE

WARNING

Before servicing or cleaning the unit, switch power off at service panel and lock service panel to prevent power

from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Hood cleaning

Avoid when choosing a detergent:

- Any cleaners that contain bleach will attack stainless steel.

- Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.

- Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive and should never be

used close to a range.

Do:

• Regularly wash with clean cloth or rag soaked with warm water

and mild phosphate-free soap or liquid dish detergent.

• Always clean in the direction of original polish lines.

• Always rinse well with clear water (2 or 3 times) after cleaning.

Wipe dry completely.

• You may also use a specialized household stainless steel

cleaner

Don’t:

• Use any steel or stainless steel wool or any other scrapers to

remove stubborn dirt.

• Use any harsh or abrasive cleansers.

• Allow dirt to accumulate.

• Let plaster dust or any other construction residues reach the

hood. During construction/renovation, cover the hood to make

sure no dust sticks to stainless steel surface.

Grease Filters

The hybrid filters should be cleaned frequently. Use a warm dishwashing detergent solution. Grease filters are dishwasher safe.

Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of the filters may occur if using phosphate

detergents, or as a result of local water conditions - but this will not affect filter performance. This discoloration is not covered by the

warranty.

19. OPERATION

BLOWER BUTTON

When blower is OFF, press this button to turn ON the blower at the last saved speed. If there was no speed saved, the blower will be set

on LOW speed.

NOTE: When LOW speed is activated from OFF, the blower starts on MEDIUM speed for a very short lapse of time, and then resume to

LOW speed.

To change the blower speed, press on this button again until the desired speed is reached (from LOW to MEDIUM to HIGH speed to OFF).

Each time a blower speed is activated, a beep is heard and LED indicators light up to show the corresponding speed chosen (lower LED

for LOW speed, lower and center LEDs for MEDIUM speed and all LEDs for HIGH speed).

When blower is on (no matter the speed level), press and hold this button until the beep sound ends; this will turn off the blower and save

this blower speed to memory.

LIGHT BUTTON

When lights are OFF, press once on this button to turn ON the lights at the last saved setting. If there was no light setting saved, the lights

will be set on LOW intensity. Press another time to set the lights on HIGH intensity. Pressing another time after the HIGH setting will turn

OFF the lights. Each time the lights are turned ON, a beep is heard and LED indicators light up to show the corresponding intensity chosen

(lower LED for LOW and both LEDs for HIGH).

When lights are on (no matter the lighting level), press and hold this button until the beep sound ends; this will turn off the lights and save

the chosen light intensity.

FILTER CLEANING REMINDER

When it is time to clean the hood and filters, the 3 blower button LED indicators will flash slowly for 30 seconds after turning the blower OFF.

This will happen every time the blower is turned OFF until the filter cleaning reminder has been reset. Once the cleaning is done, reset

the filter cleaning reminder indicators by pressing on the blower button for 3 seconds while the 3 blower button LED indicators flash slowly.

Always turn your hood on before you begin cooking to establish an air flow in the kitchen.

Let the blower run for a few minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and fresher.

Operate the hood as follows:

20. WIRING DIAGRAM

LINE

NEUTRAL

GROUND

120 V AC

CONTROL BOARD

POWER

MOTOR

OVERRIDE

LED

TRANSFORMER

RED

LED

BLK

J10

INTERFACE

USER INTERFACE

MOUNTED TO J10

ON BACK OF

CONTROL BOARD

RED

FAN MOTOR

BRN

GRY

BLU

WHT

BLK

RED (LOW)

ORG (MEDIUM

)

BLK (HIGH)

BLK

WHT

BLU

RED

BLK

BLK BLACK

BLU BLUE

BRN BROWN

GRY GREY

ORG ORANGE

RED RED

WHT WHITE

COLOR CODE

HE0236A

BLK

ORG

REPLACEMENT PARTS AND REPAIRS

In order to ensure your unit remains in good working condition, you must

use Broan-NuTone genuine replacement parts only. Broan-NuTone genuine

replacement parts are specially designed for each unit and are manufactured to

comply with all the applicable certification standards and maintain a high standard

of safety. Any third party replacement part used may cause serious damage and

drastically reduce the performance level of your unit, which will result in premature

failing. Broan-NuTone recommends to contact a certified service depot for all

replacement parts and repairs.

21. SERVICE PARTS

ITEM

NO.

PART NO.DESCRIPTION

QTY. (HOOD WIDTH)

30” 36”

1 SV63673 U

PPER FLUE MOUNTING BRACKET 11

2 SV63663 UPPER DECORATIVE FLUE, STAINLESS 11

3 SV63662 LOWER DECORATIVE FLUE, STAINLESS 11

4 S97020534 3¼” X 10” ADAPTER/DAMPER 11

5 SV08487 6” ROUND ADAPTER/DAMPER 11

6 S97020444 LED MODULE (1) 2 2

7 S97020445 TRANSFORMER 11

8 SV08582

INTERNAL BLOWER

(INCLUDING CAPACITOR)

9 SV62053

YBRID FILTER

15.875” X 14” X 0.5” (1)

10 S97020431

CAPACITIVE CONTROL

2 BUTTONS (STAINLESS)

11 SV09014 HOOD MOUNTING BRACKET 11

* SV05869 BEST LOGO 11

* SV23863 INSTALLATION GUIDE 11

* SV09027

ARTS BAG:

5 NO. 8 X 1½” COUNTERSUNK SCREWS,

8 NO. 8 X 3/4” SCREWS,

6 NO. 8 X 3/8” SCREWS,

6 DRYWALL ANCHORS, 3 WASHERS,

2 NO. 8 X 1/2” SCREWS

2 NEOPRENE PIECES

* N

OT SHOWN

HL0446

KEY

NO.

PART NO.DESCRIPTION QTY.

12 SV63628 NON-DUCT KIT UPPER DECORATIVE FLUE CHIMNEY 1

13 SV22756 6” ROUND METAL FLEXIBLE DUCT 1

14 SV63626 U

PPER PLENUM PLATE 1

15 SV63627 LOWER PLENUM PLATE 1

16 SV08487WD 6” ROUND ADAPTER 1

17 SV22759 CHARCOAL FILTER (PAIR)1

18 SV22757 CHARCOAL FILTER CLIP (SET OF 4) 1

* SV05803

PARTS BAG:

10 NO. 8-18 X 3/8” SCREWS,

4 NO. 8 X 1/2” BLACK SCREWS,

9 NO. 8-18 X 3/4” SCREWS, 4 WASHERS,

9 DRYWALL ANCHORS, 6 NO. 6 X 1/2” SCREWS.

* NOT SHOWN.

NON-DUCT KIT MODEL HRKBSS

HL0385

22. WARRANTY

FIVE-YEAR LIMITED WARRANTY FOR BEST

PRODUCTS

Warranty Period and Exclusions: Broan-NuTone, LLC (the “Company”) warrants to the consumer purchaser of its product (“you”) that the product (the

“Product”) will be free from material defects in the materials or its workmanship for a period of five (5) years from the date of original purchase (or such

longer period as may be required by applicable law) or a period of two (2) years from the date of service for any labor provided on the Product.

The limited warranty period for any replacement parts provided by the Company and for any Products repaired or replaced under this limited warranty shall

be the remainder of the original warranty period (or such longer period as may be required by applicable law).

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES AND BULBS, FUSES, FILTERS, DUCTS, ROOF CAPS, WALL CAPS

AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and service, (b) normal wear and tear, (c) any Products or

parts which have been subject to misuse, abuse, abnormal usage, negligence, accident, improper or insufficient maintenance, storage or repair (other than

repair by the Company), (d) damage caused by faulty installation, or installation or use contrary to recommendations or instructions, (f) damage caused by

exposure to salt air, (g) damage in transit, (h) natural wear of finish, (i) Products in commercial or nonresidential use, (j) damage caused by fire, flood or

other act of God, or (k) Products with altered, defaced or removed serial numbers. This warranty covers only Products sold to consumers in North America.

This warranty supersedes all prior warranties and, subject to applicable law, is not transferable from the original consumer purchaser.

No Other Warranties: This Limited Warranty contains the Company’s sole obligation and your sole remedy for defective Products. The foregoing warranties

are exclusive and in lieu of any other warranties and conditions, express or implied. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE

COMPANY DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS WARRANTIES AND CONDITIONS, AND DISCLAIMS AND EXCLUDES ALL WARRANTIES

AND CONDITIONS IMPLIED BY LAW, INCLUDING WITHOUT LIMITATION THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

To the extent that applicable law prohibits the exclusion of implied warranties or conditions, the duration of any applicable implied warranty or condition

is limited to the period specified for the express warranty above. Some jurisdictions (which may include the Province of Quebec or specific US states) do

not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Any oral or written description of the Product is

for the sole purpose of identifying it and shall not be construed as an express warranty.

Whenever possible, each provision of this Limited Warranty shall be interpreted in such manner as to be effective and valid under applicable law, but if any

provision is held to be prohibited or invalid, such provision shall be ineffective only to the extent of such prohibition or invalidity, without invalidating the

remainder of such provision or the other remaining provisions of the Limited Warranty.

Remedy: During the applicable limited warranty period, the Company will, at its option, provide replacement parts for, or repair or replace, without charge,

any Product or part thereof, to the extent the Company finds it to be covered by and in breach of this limited warranty under normal use and service. The

Company will ship the repaired or replaced Product or replacement parts to you at no charge. You are responsible for all costs for removal, reinstallation

and shipping, insurance or other freight charges incurred in the shipment of the Product or part to the Company. If you must send the Product or part

to the Company, as instructed by the Company, you must properly pack the Product or part—the Company is not responsible for damage in transit. The

Company reserves the right to utilize reconditioned, refurbished, repaired or remanufactured Products or parts in the warranty repair or replacement

process. Such Products and parts will be comparable in function and performance to an original Product or part and warranted for the remainder of the

original warranty period (or such longer period as may be required by applicable law).

Company reserves the right, in its sole discretion, to refund the money actually paid by you for the Product. If the Product or component is no longer

available, replacement may be made with a similar product of equal or greater value, at Company’s sole discretion. This is your sole and exclusive remedy

for breach of this limited warranty.

Exclusion of Damages: THE COMPANY’S OBLIGATION TO PROVIDE REPLACEMENT PARTS, OR REPAIR OR REPLACE, AT THE COMPANY’S OPTION,

SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY AND THE COMPANY’S SOLE AND EXCLUSIVE OBLIGATION. THE

COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH

THE PRODUCT, ITS USE OR PERFORMANCE.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply

to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from jurisdiction to jurisdiction. The disclaimers,

exclusions, and limitations of liability under this warranty will not apply to the extent prohibited by applicable law.

This warranty covers only replacement or repair of defective Products or parts thereof at the Company’s main facility and does not include the cost of field

service travel and living expenses.

Any assistance the Company provides to or procures for you outside the terms, limitations or exclusions of this limited warranty will not constitute a waiver

of such terms, limitations or exclusions, nor will such assistance extend or revive the warranty. The Company will not reimburse you for any expenses

incurred by you in repairing or replacing any defective Product, except for those incurred with the Company’s prior written permission.

How to Obtain Warranty Service: To qualify for warranty service, you must (a) notify the Company at the address or telephone number stated below within

seven (7) days of discovering the covered defect, (b) give the model number and part identification and (c) describe the nature of any defect in the Product

or part. At the time of requesting warranty service, you must present evidence of the original purchase date. If you cannot provide a copy of the original

written limited warranty, then the terms of the Company’s most current written limited warranty for your particular product will control.

PRODUCT SPECIFICATIONS

All illustrations and specifications in this catalog are based on the latest product information available at time of production. Broan-NuTone, LLC and

BEST® reserves the right to make changes at any time, without notice, in prices, colors, materials, equipment, specifications and models, place of

manufacture and to discontinue models or equipment.

Best

Broan-NuTone, LLC- 926 W. State Street, Hartford, WI 53207 1-800-637-1453

Best®, 550 Lemire Blvd., Drummondville, QC, Canada (1-866-737-7770) www.bestrangehoods.com

SÉRIE WCP3I

HB0311

GUIDE D'INSTALLATION

BEST; Hartford, Wisconsin www.BestRangeHoods.com 800 558-1711

BEST; Drummondville, QC, Canada www.BestRangeHoods.ca 866 737-7770

23863 rév. 03

CONÇUE POUR USAGE RÉSIDENTIEL SEULEMENT

INSTALLATEUR : LAISSER CE GUIDE AU PROPRIÉTAIRE.

PROPRIÉTAIRE : DIRECTIVES D’UTILISATION ET D’ENTRETIEN

AUX PAGES 12 ET 13.

LIRE ET CONSERVER CES DIRECTIVES

! !

AFIN DE RÉDUIRE LES RISQUES D’INCENDIE,

D’ÉLECTROCUTION OU DE BLESSURES CORPORELLES,

SUIVEZ LES DIRECTIVES CI-DESSOUS :

1. N’utilisez cet appareil que de la façon prévue par le

manufacturier. Si vous avez des questions, contactez le

manufacturier à l’adresse ou au numéro de téléphone indiqués

dans la garantie.

2. Avant de réparer ou de nettoyer l’appareil, couper l’alimentation

électrique en verrouillant le panneau de distribution afin

d’éviter sa remise en marche accidentelle. Si le panneau de

distribution ne peut être verrouillé, y fixer un avertissement en

évidence, telle qu’une étiquette de couleur vive.

3. Les travaux d’installation et de raccordement électrique doivent

être effectués par une personne qualifiée, conformément

aux codes et aux standards de construction, incluant ceux

concernant la protection contre les incendies.

4. Une quantité d’air adéquate est requise afin d’assurer une

bonne combustion et l’évacuation des gaz par la cheminée

dans le cas des équipements alimentés au gaz afin de

prévenir les retours de cheminée. Suivez les instructions et

conformez-vous aux standards de sécurité des manufacturiers

d’équipement de chauffage, tel qu’ils sont publiés par la

National Fire Protection Association (NFPA) et l’American

Society for Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE) ainsi que les responsables des

codes locaux.

5. Veillez à ne pas endommager le câblage électrique ou d’autres

équipements non apparents lors de la découpe ou du perçage

du mur ou du plafond.

6. Les ventilateurs avec conduits doivent toujours évacuer l’air

à l’extérieur.

7. Ne pas utiliser cet appareil avec une commande de vitesse à

semi-conducteur additionnelle.

8. Afin de réduire les risques d’incendie, n’utilisez que des conduits

de métal.

9. Cet appareil doit être mis à la terre.

10. Lorsqu’une réglementation est en vigueur et qu’elle comporte

des exigences d’installation et/ou de certification plus

restrictives, lesdites exigences prévalent sur celles de ce

document et l’installateur entend s’y conformer à ses frais.

AFIN DE RÉDUIRE LES RISQUES DE FEU DE

CUISINIÈRE :

a) Ne jamais laisser les appareils de cuisson sans surveillance

lorsqu’ils sont réglés à feu vif. Les débordements engendrent

de la fumée et des déversements graisseux pouvant

s’enflammer. Chauffez l’huile lentement, à feu doux ou moyen.

b) Mettez toujours la hotte en marche lorsque vous cuisinez à feu

vif ou que vous cuisinez des mets flambés (par ex. : crêpes

Suzette, cerises jubilées, steaks au poivre flambés).

c) Nettoyez régulièrement le ventilateur. Ne laissez pas la graisse

s’accumuler sur le ventilateur, les filtres ou les conduits

d’évacuation.

d) Utilisez le bon format de casserole. Servez-vous toujours de

casseroles et d’ustensiles appropriés à la dimension de la

surface chauffante.

1. Pour une utilisation à l’intérieur seulement.

2. Pour usage domestique seulement. Ne pas utiliser pour évacuer

des vapeurs ou des matières dangereuses ou explosives.

3. Afin d’éviter tout dommage au moteur ou de déséquilibrer

ou de rendre bruyante la roue du moteur, garder votre

appareil à l’abri des poussières de gypse et de construction/

rénovation,etc.

4. Le moteur de votre hotte possède une protection thermique

qui arrêtera automatiquement le moteur s’il surchauffe. Le

moteur redémarrera automatiquement une fois refroidi. Si le

moteur continue à arrêter et à redémarrer, faites-le vérifier.

5. Pour une meilleure évacuation des odeurs de cuisson, le

bas de votre hotte devrait être situé à un minimum de 24 po

(30 po pour une cuisinière à gaz) et à un maximum de 30 po

au-dessus de la table de cuisson.

6. Deux installateurs sont recommandés lors de l’installation vu

la grande dimension et le poids de cette hotte.

7. Afin de réduire les risques d’incendie, assurez-vous d’évacuer

l’air à l’extérieur. Ne pas évacuer l’air dans des espaces

restreints comme l’intérieur des murs ou plafonds ou dans le

grenier, faux plafond ou garage.

8 En raison de la grande capacité d’évacuation de cette hotte,

il est recommandé d’ouvrir une fenêtre dans ou près de la

cuisine afin de remplacer l’air évacué.

9. Afin de réduire les risques d’incendie et d’électrocution, la

hotte Best de la série WCP3I ne doit être installée qu'avec son

ventilateur intérieur intégré.

10. Afin de réduire les risques de feu ou d'électrocution, si la

hotte est utilisée en mode recirculation, utiliser uniquement

l'ensemble de recirculation modèle HRKBSS.

11. Veuillez consulter l’autocollant apposé à l’intérieur de la hotte

pour plus d’information ou autres exigences.

AVERTISSEMENT

ATTENTION

AVERTISSEMENT

AFIN D’ÉVITER TOUT RISQUE DE BLESSURES LORS

D’UN FEU DE CUISINIÈRE, SUIVEZ CES DIRECTIVES* :

1. Étouffez les flammes avec un couvercle hermétique,

une tôle à biscuits ou un plateau métallique et ensuite,

éteindre le brûleur. PRENEZ SOIN D’ÉVITER LES

BRÛLURES. SI LES FLAMMES NE S’ÉTEIGNENT PAS

IMMÉDIATEMENT, ÉVACUEZ LES LIEUX ET APPELEZ

LES POMPIERS.

2. NE PRENEZ JAMAIS UNE CASSEROLE EN FLAMMES

DANS VOS MAINS. Vous pourriez vous brûler.

3. N’UTILISEZ PAS D’EAU, incluant un linge à vaisselle ou une

serviette mouillée, cela pourrait occasionner une violente

explosion de vapeur.

4. N’utilisez un extincteur QUE DANS LE CAS OÙ :

A. Vous savez qu’il s’agit d’un extincteur de classe ABC et

que vous en connaissez le fonctionnement.

B. Le feu est petit et limité

à l’endroit où il a débuté.

C. Les pompiers ont été avisés.

D. Vous pouvez combattre le feu en ayant accès à une sortie

de secours.

*Tirées du Kitchen Fire Safety Tips publié par la NFPA.

HH0246F

CONDUIT DE

3¼ PO X 10 PO

OU 6 PO ROND

CAPUCHON DE TOIT

CONDUIT DE

3¼

PO X 10 PO

CAPUCHON

MURAL

HOTTE

CONDUIT

DÉCORATIF

VOIR LE TABLEAU

POUR

LA DISTANCE

AU-DESSUS DU

PLAN DE CUISSON

Avant de commencer l'installation de la hotte, retirer le support d'expédition (en gris),

ainsi que les vis qui le retiennent à la hotte et s'en défaire. Voir l'illustration de droite.

HD0937

EMPLACEMENT

DES VIS

1. PRÉPARER L'INSTALLATION

AVERTISSEMENT

Il est recommandé de porter des lunettes et des gants de sécurité lors de l’installation, de l’entretien et de la

réparation de cet appareil.

HAUTEUR DU PLAFOND

DISTANCE MINIMALE DE LA HOTTE

-DESSUS DE LA SURFACE DE CUISSON

D'UNE CUISINIÈRE ÉLECTRIQUE

DISTANCE MINIMALE DE LA HOTTE

AU-DESSUS DE LA SURFACE DE

CUISSON D'UNE CUISINIÈRE À GAZ

8 PIEDS 24 POUCES 30 POUCES

9 PIEDS 28½ POUCES 30 POUCES

10 PIEDS* 28½ POUCES 30 POUCES

* Une rallonge de conduit décoratif est requise pour les plafonds de 10 pi, modèle AEWCP3SB (vendue séparément).

NOTE : Avant de commencer l'installation, vérifier le contenu de la boîte. Si des pièces sont manquantes ou endommagées, contacter le

manufacturier.

S'assurer que les articles suivants sont inclus :

- Hotte

- Accessoires • Ensemble de conduit décoratif (conduits inférieur et supérieur)

• Support de montage de la hotte

• Support de montage du conduit décoratif supérieur

• 2 filtres hybrides

• Adaptateur/volet de 6 po rond (pour évacuation verticale), dans un sac à part

• Adaptateur/volet de 3¼ po x 10 po (pour évacuation horizontale ou verticale)

• Sac de pièces comprenant : 5 vis à tête fraisée n° 8 x 1½ po, 8 vis n° 8 x 3/4 po, 6 vis n° 8 x 3/8 po, 6 douilles à

expansion, 3 rondelles, 2 vis n° 8 x 1/2 po, 2 morceaux de néoprène. Jeter la

quincaillerie excédentaire s'il y a lieu.

Pièces vendues séparément :

- Conduits, coudes, capuchons de mur ou de toit.

- Rallonge de conduit décoratif pour plafonds de 10 pi. modèle AEWCP3SB.

- Ensemble de recirculation modèle HRKBSS, obligatoire pour une installation en recirculation.

NOTE : La hauteur du plafond ne doit pas excéder 9 pi pour une installation sans conduit.

2. CHOISIR LE TYPE D'INSTALLATION

2.1 INSTALLATION EN RECIRCULATION

Un ensemble de recirculation modèle HRKBSS est requis pour ce type d'installation.

2.2 INSTALLATION AVEC CONDUITS

Déterminer à quel endroit et de quelle façon les conduits seront installés.

Installer des conduits de dimensions adéquates, des coudes et un capuchon de toit ou de

mur selon le type d’installation choisi.

Pour une évacuation verticale, utiliser des conduits ronds de 6 po ou des conduits de

3¼ po x 10 po et pour une évacuation horizontale,utiliser des conduits de 3¼ po x 10 po.

Se servir de ruban adhésif de métal pour assurer l’étanchéité des joints.

2.3 TOUTES LES INSTALLATIONS

La distance minimale entre le bas de la hotte et la surface de cuisson est de 24 po (30 po

au-dessus d'une cuisinière à gaz). Un maximum de 30 po au-dessus de la surface de

cuisson est recommandé pour une meilleure évacuation des odeurs de cuisson.

Les distances au-delà de 30 po sont à la discrétion de l’installateur et de l’utilisateur, si la

hauteur du plafond et du conduit décoratif le permettent.

NOTE : Lors de l'installation, protéger la surface de cuisson ou le comptoir de cuisine.

2. CHOISIR LE TYPE D'INSTALLATION (SUITE)

Se référer aux illustrations ci-dessous pour l’emplacement des conduits selon le type d’évacuation choisi (les pièces en gris seront

installées plus tard).

3. RETIRER LES FILTRES HYBRIDES

Poser la hotte à plat sur une table. Retirer les rubans adhésifs des filtres. Retirer les filtres en les

poussant vers le bas et en les dégageant de la hotte, puis les mettre de côté.

Retirer les deux morceaux de styromousse ainsi que le ruban adhésif d'en dessous du

ventilateur et s'en défaire.

3 PO

/8 PO

9¾ PO

HK0258F

/16 PO

HOTTE DE 30 PO DE LARGEUR

HOTTE DE 36 PO DE LARGEUR

3¼ PO

15/16 PO

/8 PO

/16 PO

9¾ PO

HK0273F

/16 PO

HOTTE DE 30 PO DE LARGEUR

HOTTE DE 36 PO DE LARGEUR

3¼ PO

HK0261F

/16 PO

HOTTE DE 30 PO DE LARGEUR

HOTTE DE 36 PO DE LARGEUR

6 PO DIA.

HD1099

ÉVACUATION VERTICALE OU INSTALLATION EN RECIRCULATION

ÉVACUATION VERTICALE

ÉVACUATION HORIZONTALE

La page charge ...

Best WCP3I30SB Guide d'installation

Marque: Best

Modèle: WCP3I30SB

Catégorie: Hottes

Taper: Guide d'installation

Ce manuel convient également à

WCP3I36SB

Télécharger le PDF

rapport

dans d''autres langues

English: Best WCP3I30SB Installation guide
español: Best WCP3I30SB Guía de instalación

Best WCP3I30SB Guide d'installation

Ce manuel convient également à

Best WCP3I30SB Guide d'installation

dans d''autres langues

Documents connexes

Autres documents