Samsung NK30R5000WG Guide d'installation

Marque: Samsung

Modèle: NK30R5000WG

Catégorie: Hottes

Taper: Guide d'installation

Ce manuel convient également à

Range Hood

Hotte de la cuisine

Campana de cocina

Installation Instructions Guide

Guide d’instructions d’installation

Guía de Instrucciones para Instalación

NK36R5000WG/AA, NK30R5000WG/AA

NK36R5000WS/AA, NK30R5000WS/AA

LIB0154965

2 English

Important Safety Instructions 3

Installation Requirements 4

Electrical Requirements 4

Before Installing the Hood 4

Venting Methods 4

Tools and Parts 5

Dimensions and Clearances 5

Installation 6

Installation Instructions 6

Install the Range Hood 7

Install Duct Covers 8

Electrical Connection 8

Range Hood Use and Care 9

Description of the Hood 9

Control 9

Maintenance 9

Accessories 10

Range Hood for ADA Compliance 11

Warranty (USA) 12

Warranty (Canada) 13

Table of Contents

English 3

APPROVED FOR RESIDENTIAL APPLIANCES

FOR RESIDENTIAL USE ONLY

READ AND SAVE THESE INSTRUCTIONS

PLEASE READ ENTIRE INSTALLATION GUIDE BEFORE PROCEEDING.

INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.

IMPORTANT: Save these Instructions for the Local Electrical

Inspector’s use.

INSTALLER: Please leave these Instructions with this unit for

the owner.

OWNER: Please retain these instructions for future

reference.

Symbols used in this manual

WARNING

Hazards or unsafe practices that may result in severe personal injury or

death.

CAUTION

Hazards or unsafe practices that may result in electric shock, personal

injury, or property damage.

NOTE

Useful tips and instructions

These warning icons and symbols are here to prevent injury to you and

others.

Please follow them explicitly. After reading this section, keep it in a safe

place for future reference.

WARNING

Turn off the power circuit at the service panel and lock

out panel before wiring this appliance.

Requirement 120 VAC, 60 Hz. 15 or 20 A Branch Circuit

WARNING

Cancer and Reproductive Harm - www.P65Warnings.ca.gov

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING PRECAUTIONS:

■ Use this unit only in the manner intended by the manufacturer. If you

have questions, contact the manufacturer.

■ Before servicing or cleaning the unit, switch the power off at the

service panel and lock the service panel to prevent power from being

switched on accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warning device, such

as a tag to the service panel.

■ Installation work and electrical wiring must be done by qualied

person(s) in accordance with all applicable codes and standards,

including re-rated construction.

■ Sufcient air is needed for proper combustion and exhausting of

gases through the ue (chimney) of fuel burning equipment to

prevent backdrafting. Follow the heating equipment manufacturer’s

guideline and safety standards such as those published by the

National Fire Protection Association (NFPA), the American Society

for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE),

and the local code authorities.

Important Safety Instructions

■ When cutting or drilling into the wall or ceiling; do not damage

electrical wiring and other hidden utilities.

■ Ducted fans must always be vented to the outdoors.

CAUTION

For general ventilating use only. Do not use to exhaust hazardous or

explosive materials and vapors.

CAUTION

To reduce the risk of re and to properly exhaust air, be sure to duct air

outside - do not vent exhaust air into spaces within walls or ceilings, or

into attics, crawl spaces or garages.

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

WARNING

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

■ Never leave surface units unattended at high settings. Boilovers

cause smoking and greasy spillovers that may ignite. Heat oils slowly

on low or medium settings.

■ Always turn the hood ON when cooking at high heat or when ambeing

food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

■ Clean ventilating fans frequently. Grease should not be allowed to

accumulate on the fan or lter.

■ Use proper pan sizes. Always use cookware appropriate for the size

of the surface element.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF

A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING

PRECAUTIONS:

■ SMOTHER FLAMES with a close tting lid, cookie sheet, or metal

tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.

If the ames do not go out immediately, EVACUATE AND CALL THE

FIRE DEPARTMENT.

■ NEVER PICK UP A FLAMING PAN - you may be burned.

■ DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result

■ Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you already know

how to operate it.

– The re is small and contained in the area where it started.

– The re department is being called.

– You can ght the re with your back to an exit.

Based on “Kitchen Fire Safety Tips” published by NFPA.

WARNING

To reduce the risk of re or electrical shock, do not use this fan with any

solid-state speed control device.

WARNING

Do not let children near this appliance. Do not let children play with this

appliance.

Keep all packaging materials out of children’s reach. Properly dispose the

packaging materials after this appliance is unpacked.

NOTE

Suitable for use in household cooking area.

Read and save this instructions

4 English

Installation Requirements

Electrical Requirements

IMPORTANT

Observe all governing codes and ordinances.

It is the customer’s responsibility:

■ To contact a qualied electrical installer.

■ To assure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70

— latest edition*, or CSA Standards C22.1-94, Canadian

Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all

local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended

that a qualied electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

Other Requirements

■ A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.

■ If the house has aluminum wiring, follow the procedure below:

1. Connect a section of solid copper wire to the pigtail leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools designed

and UL listed for joining copper to aluminum.

■ Follow the electrical connector manufacturer’s recommended

procedure. Aluminum/copper connections must conform with local

codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating of the

appliance as specied on the model/serial rating plate. The model

serial plate is located behind the lter on the rear wall of the range hood.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards

C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No.

0-M91 (latest edition) and all local codes and ordinances.

■ A U.L.- or C.S.A.-listed conduit connector must be provided at each

end of the power supply conduit (at the range hood and at the

junction box).

Before installing the Hood

• The Vent system must terminate outdoors.

• For the most efcient air ow exhaust, use a straight run or as few

elbows as possible. CAUTION: Vent unit to outside of building, only.

• At least two people are necessary for installation.

• Fittings material are provided to secure the hood to most types of

walls and ceilings. Consult a qualied installer to conrm that

the ttings are suitable for your cabinets, walls, and ceiling.

• Do not use exible ducting.

• COLD WEATHER installations should have an additional backdraft

damper installed to minimize backward cold air ow and a

nonmetallic thermal break to minimize conduction of outside

temperatures as part of the ductwork. The damper should be on the

cold air side of the thermal break. The break should be as close as

possible to where the ducting enters the heated portion of the house.

Venting Methods

Closely follow the instructions set out in this manual. Samsung is not

responsible for any eventual inconveniences, damages or res caused by

not complying with the instructions in this manual.

Ducting version

The hood is equipped with a 6” (15.2 cm) round transition for discharge of

fumes to the outside.

Horizontal Discharge Vertical Discharge Horizontal Discharge

A. Wall cap

B. 6” (15.2 cm) round vent

A. Roof cap

B. 6” (15.2 cm) round vent

A. Deector

B. 6” (15.2 cm) round vent

Preparation

Do not cut a joist or stud unless absolutely necessary. If a joist or stud

must be cut, then a supporting frame must be constructed.

Fittings material are provided to secure the hood to most types of walls/

ceilings.

However, a qualied technician must verify that the ttings are suitable

for your cabinets, walls, and ceiling.

Before making cutouts, make sure there is proper clearance within the

ceiling or wall for the exhaust vent.

Ductless version (Recirculating)

For installations where cooking fumes and vapor cannot be discharged

to the outside, attach a charcoal lter and the deector on the duct cover

support bracket. Fumes and vapors will be recycled through the top grille

by a duct connected to the transition and the transition mounted on the

deector.

NOTE

For horizontal discharge only: purchase the Ductless Recirculating Kit.

Minimum Duct Size: 6” Round Pipe.

CAUTION

■ For electric/induction cooktop & range installations: Mount the hood

so the bottom is at least 24” (61cm) above the cooking surface.

■ For gas cooktop & range installations: Mount the hood so the bottom

is at least 27” (68.6 cm) above the cooking surface.

■ For both, mount no higher than 36” (91.4 cm) above the cooking

surface.

■ Measure the mounting height from the surface of the range to the

bottom of the hood.

WARNING

This hood is intended for household use.

PLEASE READ THE INSTALLATION MANUAL FOR THE HOOD´S

SPECIFIC APPLICATION. Check your ceiling height and the hood´s

height before selecting your hood.

Installation Requirements

English 5

Tools and Parts

Removing the packaging

CAUTION

Remove the carton carefully. Wear gloves to protect against sharp edges.

WARNING

Remove the protective lm covering the product before putting it into

operation.

Parts supplied

• Hood assembly with blower and LED lamps already installed.

• Hardware bag with:

Part Qty Part Qty

5x45 mm

8x40 mm

5.4x75 mm

10x60 mm

3.5x9.5 mm

Duct cover bracket

2.9x6.5 mm

Mounting template

Duct Covers

6” round transition

Tools/Materials required

• Level

• Drill with 1¼” (3.2 cm),

⁄8” (3.2 mm), and

⁄16” (4.8 mm) drill bits

• Pencil

• Wire stripper or utility knife

• Tape measure or ruler

• Pliers

• Caulking gun and weatherproof caulking compound

• Jigsaw or keyhole saw

• Metal snips

• Screwdrivers:

• Phillips

• Flat - blade

Parts needed

• Home power supply cable

• ½” (12.7 mm) UL listed or CSA approved strain relief

• 3 UL listed wire connectors

• 1 wall or roof cap

• Metal vent system

Optional accessories and consumable parts

MODEL

NK30R5000WS

NK36R5000WS

NK30R5000WG

NK36R5000WG

Extension Kit NK-AE505PWS/AA NK-AE505PWG/AA

Recirculating

Kit

NK-AF020FNB/AA

Charcoal

Filter

NK-AR040FNB/AA

* Order the needed kit specifying your hood model.

Dimensions and Clearances

NK30R5000WS

NK36R5000WS

NK30R5000WG

NK36R5000WG

A 30” (76.2 cm) 36″ (91.2 cm)

B 19

⁄16″ (50 cm)

Max: 42

⁄8″ (107 cm)

Min: 28

⁄16″ (72 cm)

D**

Max: 38

⁄16″ (97 cm)

Min: 28

⁄16″ (72 cm)

E 6” (15.24 cm)

F 7

⁄16″ (18.3 cm)

G 8

⁄16″ (20.8 cm)

* Ductless (Recirculating) version

** Ducted version

Installation Requirements

6 English

Installation Instructions

We recommend that a qualied technician install the range hood. It is the

installer’s responsibility to ensure the range hood complies with the instal-

lation clearances speciations for the product.

• It is recommended that the vent system be installed before the hood is

installed.

• Before making cutouts, make sure there is proper clearance within the

ceiling or wall for the exhaust vent.

• Conrm that all installations parts have been removed from the

shipping carton.

WARNING

To reduce the risk of re, electric shock, or injury to persons, observe the

following.

• Shut off power to the circuit you will be attaching the hood to at the

circuit breaker panel or fuse box.

• Determine which venting method to use: roof, wall, or nonvented.

• Select a at surface for assembling the range hood.

Place a covering over that surface.

• Always have 2 or more persons lift or move the range hood.

Mounting the duct cover bracket

1. Determine and mark the centerline on the wall where the canopy

hood will be installed. Shut off power at the circuit breaker panel or

fuse box.

2. Select a mounting height of no less than 24” (61 cm) above an electric

cooking surface or 27” (68.6 cm cm) above a gas cooking surface.

3. Tape the template in place, aligning the template center line and

bottom with the hood center line and hood bottom line marked on

the wall.

A. Centerline

B. Fastener locations

C. Mounting height reference (hood bottom line)

4. Mark the centers of the fastener locations on the wall by pushing a

pencil point through the template.

IMPORTANT: All screws must be installed into the wood studs or

framing. If there is no wood to screw into, additional wall framing

supports may be required.

5. Remove the template.

6. Drill

⁄16″ (4.8 mm) pilot holes at all locations where screws are going

to be installed into wood.

7. Install the 2 - 5 x 45 mm mounting screws. Leave a

⁄4″ (6.4 mm) gap

between the wall and the back of the screw head to slide the range

hood into place.

⁄4″ (6.4 mm)

8. Attach the vent cover bracket to the wall ush to the ceiling using 2 -

5 x 45mm screws.

A. 8 x 40 mm anchors

B. Centerline on wall

C.Vent cover support bracket

D. 5 x 45 mm screws

Complete preparation

1. Determine and make all necessary cuts in the wall for the vent system.

Install the vent system before installing the hood. See “Venting

Requirements” section.

2. Determine the required height for the home power supply cable and

drill a 1¼” (3.2 cm) hole at this location.

3. Run the home power supply cable according to the National Electrical

Code or CSA Standards and local codes and ordinances. There must

be enough ½” conduit and wires from the fused disconnect (or circuit

breaker) box to make the connection in the hood’s electrical terminal

box.

NOTE

Do not turn on power until the installation is complete.

4. Use caulk to seal all openings

Installation

English 7

Installation

Install the Range Hood

WARNING

USE TWO OR MORE PEOPLE TO MOVE AND INSTALL THE RANGE

HOOD. FAILURE TO DO SO CAN RESULT IN BACK OR OTHER

INJURY.

1. Mark the lower mounting hole locations with a pencil .

2. Uninstall the hood assembly, and drill

⁄16”” (4.8 mm) pilot holes at

the marked locations.

3. Hang the range hood again on 2 the upper mounting screws.

4. Level the range hood and tighten the upper mounting screws.

5. Install 2 - 5 x 45 mm lower mounting screws and tighten. Use the

optional wall anchors if needed.

A. Mounting screws

B. Mounting slots

C. Lower mounting screws

Connect the vent system

1. Install the transition on top of the hood (if removed for shipping) with

2-3.5x9.5 mm sheet metal screws.

A. Vent transition

B. 3.5 x 9.5 mm screw

For vented installations only

1. Fit the vent system over the exhaust outlet.

2. Measure from the bottom of the air deector to the bottom of the

hood outlet. Cut the ductwork at the measured dimension.

Roof Outlet

Dimension to

measure

Wall

outlet

3. Seal the connection with clamps.

4. Conrm that the back draft dampers work properly

Install the Duct Covers

When using both upper and lower vent covers, push the lower cover

down onto the hood and lift the upper cover to the ceiling, and then install

with two mounting screws.

NOTE

For vented installations, the upper vent cover may be reversed to hide

slots.

A.. Upper vent cover

B. Lower vent cover

C. 2.9 x 6.5 mm screws

D. Bracket

Installation

8 English

NOTE

To prevent scratches, lay paper or a kitchen towel over the edges of the

lower ue duct to protect the surface.

Complete Installation

• For non-vented (recirculating) installations only, install charcoal

lters over metal grease lter. See the “Accessories” section.

• Install metal lters. See the “Maintenance” section.

Electrical Connection

WARNING

Electrical shock hazard.

WARNING

Shut off power at the circuit breaker panel or fuse box before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

WARNING

Electrically ground the blower.

Connect the ground wire to the green and yellow ground wire in the

terminal box. Failure to do so can result in death or electrical shock.

1. Shut off power at the circuit breaker panel or fuse box.

2. Remove the terminal box cover.

3. Remove the knockout in the terminal box cover and install a UL listed

or CSA approved

⁄

” strain relief.

4. Run the home power supply cable through the strain relief, into

the terminal box.

A. Home power supply cable

B. UL listed wire connectors

C. White wires (N)

D. Black wires (L)

E. Green (or bare) and

yellow-green ground

5. Use UL listed wire connectors and connect the black wires (D)

together.

6. Use UL listed wire connectors and connect the white wires (C)

together.

7. Connect the green (or bare) ground wire from the home power supply

to the yellow-green ground wire (E) in the terminal box using UL listed

wire connectors.

8. Tighten the strain relief screw.

9. Install the terminal box cover.

10. Turn on the power.

To get the most efcient use from your new range hood, read the

“Maintenance” section. Keep your Use, Care, and installation Guide close

to the range hood for easy reference.

Installation

English 9

Range Hood Use and Care

Description of the Hood

1. Blower and light controls

2. LED lamps

3. Grease lter handle

4. Grease lters

5. Duct covers

Control

A B C ED

A. Light On/Off

B. Off button

C. Low button

D. Med button

E. High button

Operating the light

The Light On/Off button (A) controls both lights. Press once

for On and again for Off.

Operating the blower

The Blower OFF button (B) turns the blower off.

The Blower Speed buttons (C,D,E) set the desired speed and control the

sound level for quiet operation. The speed can be changed anytime dur-

ing fan operation by pressing the desired blower speed button.

1. To Turn the Blower On, press a Blower Speed button (C,D,E).

2. To Turn the Blower off, press the Blower OFF Button (B).

Maintenance

Cleaning

Do not spray cleaners directly onto the controls while cleaning the Hood.

The hood should be cleaned regularly internally (at least as often as you

clean the grease lters and externally. Clean using a cloth dampened with

neutral liquid detergent. Do not use abrasive products.

DO NOT USE ALCOHOL!

Grease Filter

Traps cooking grease particles. Th grease lter must be cleaned once a

month using a mild detergent, either by hand or in a dishwasher, which

must be set to a low temperature and a short cycle. When washed in a

dishwasher, the grease lter may discolor slightly, but this does not affect

its ltering capacity. To remove the grease lter, pull the spring release

handle.

A. Spring release handle

WARNING

Failure to carry out these basic cleaning recommendations for the

hood and failure to clean the grease lter may cause re risks.

Therefore, we strongly recommend you follow these instructions.

Samsung is not responsible for any damage to the motor or for any

re damage linked to inappropriate maintenance or failure to observe

these cleaning and safety recommendations.

Replacing a LED lamp

The LED lights are replaceable by a service technician only. See the

warranty for service contact information.

Range Hood Use and CareRange Hood Use and Care

10 English

Accessories

For non-vented (recirculating) installation only

NOTE

To reduce the risk of re or shock when the hood is used in recirculation

mode, use only the conversion kit models listed below:

Recirculating kit: NK-AF020FNB/AA

Charcoal Filter Replacement kit: NK-AR040FNB/AA

To attach the recirculation kit, follow these steps:

1. Assemble the air deector with the duct cover bracket with 2 -

assembly screws provided with the Recirculation Kit.

A. Vent cover bracket

B. 2.9 x 6.5 mm screws

C. Deector

2. Measure from the bottom of the air deector to the bottom of the

hood outlet.

A. Air deector

B. Vent clamp

C. X = length to cut vent duct

D. Vent duct

E. Exhaust outlet

3. Cut the duct to the measured size (X).

4. Remove the air deector.

5. Slide the duct onto the bottom of the air deector.

6. Place the assembled air deector and duct over the exhaust outlet

from the hood.

7. Re-attach the air deector to the duct cover bracket with 2

assembly screws.

8. Seal the connections with vent clamps

Charcoal lter

The charcoal lter is not washable. It should last up to 6 months

with normal use. Replace with Charcoal Filter Replacement Kit.

To replace charcoal lter:

1. Remove the metal grease lter from the range hood.

2. Bend the spring clips away from the metal grease lter.

3. Place the charcoal lter into the top side of metal lter.

4. Insert the metal grease lter back into the range hood.

Range Hood for ADA Compliance

Range Hood Use and Care

English 11

Range hoods can be installed to comply with Sections 308 and 309 of

ADA Guidelines, when used with appropriately mounted controls installed

at 15” (38.1 cm) to 40” (101.6 cm) above the oor and control access

does not require reaching over a cooking appliance.

The following range hoods NK30R5000WS, NK36R5000WS,

NK30R5000WG, NK36R5000WG can work in an ADA Compliant

situation when the range hood is wired to operate from a dedicated,

standard electrical wall switch. To facilitate this application, share the

information on the following pages with your electrician when preparing

for the installation.

NOTE

All the models can be controlled by only one remote switch (The switch

activates or deactivates the motor and the light of the hood).

WARNING

All electrical work must be done in accordance with local codes,

ordinances, or the national electrical code as applicable. For safety, this

product must be installed in a grounded switch box. The electrical wiring

installation must be done by a qualied technician.

WARNING

Electrical Shock Hazard

Turn off power at the circuit breaker panel or fuse box before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

(L, ground)

(N, ground)

POWER SUPPLY HOME

A. Range Hood Cable

B. UL listed wire connector

C. White wires (N)

D. Black wires (L)

E. Green (or bare) and

yellow-green ground

F. UL listed switch

G. Home power supply cable

H. Deep single gang switch box

Range Hood Use and CareRange Hood Use and Care

WARNING

To avoid re or electrical shock, turn off power at the circuit breaker

panel or fuse box. Conrm that the power is off before wiring.

1. MOUNT THE SWITCH BOX . Install a 3½” deepsingle gang switch

box

2. ATTACH THE POWER CABLE. Clamp wiring to the switch box and

unit using an appropriate clamp. Provide 6” leads inside the box and

fan for easier wiring.

3. CONNECT THE WIRING. General instructions:

• Make sure both the switch box and the appliance are properly

grounded.

• Make sure the ground wire is securely fastened to the control’s

ground screw. Tighten the ground screw.

• Use proper wire nut sizes for the number and size of the wires.

• For push-in and screw terminals: Use min. #14 AWG solid copper

wire only.

• Tighten the screw terminals.

• Make electrical connections following the appropriate diagram.

BLACK

WHITE

APPLIANCE

GRND

120 VAC

LOAD

SINGLE

G ANG

SWITCH

BOX

4. MOUNT THE CONTROL IN THE SWITCH BOX. Tuck wires into

the switch box and fasten the control to the box using the attached

screws.

5. ATTACH THE SWITCH PLATE. Fasten the switch plate to the control

using the short screws from the parts bag.

Range Hood Use and Care

warranty (USA)

SAMSUNG RANGE HOOD

Limited warranty to original purchaser

This SAMSUNG brand product, as supplied and distributed by

Samsung Electronics America, Inc. (SAMSUNG) and delivered

new, in the original carton to the original consumer purchaser, is

warranted by SAMSUNG against manufacturing defects in mate-

rials and workmanship for a limited warranty period of:

ONE (1) YEAR PARTS AND LABOR

This limited warranty begins on the original date of purchase,

and is valid only on products purchased and used in the United

States. To receive warranty service, the purchaser must contact

SAMSUNG for problem determination and service procedures.

Warranty service can only be performed by a SAMSUNG au-

thorized service center. The original dated bill of sale must be

presented upon request as proof of purchase to SAMSUNG or

SAMSUNG’s authorized service center.

SAMSUNG will repair or replace this product, at our option and

at no charge as stipulated herein, with new or reconditioned

parts or products if found to be defective during the limited

warranty period specied above. All replaced parts and prod-

ucts become the property of SAMSUNG and must be returned

to SAMSUNG. Replacement parts and products assume the

remaining original warranty, or ninety (90) days, whichever is

longer.

In-home service will be provided during the warranty labor

period subject to availability within the contiguous United States.

In-home service is not available in all areas. To receive in-home

service, the product must be unobstructed and accessible to

service personnel. If during in-home service repair can not be

completed, it may be necessary to remove, repair and return the

product.

This limited warranty covers manufacturing defects in materials

and workmanship encountered in normal, noncommercial use of

this product and shall not apply to the following, including, but

not limited to: damage which occurs in shipment; delivery and

installation; applications and uses for which this product was not

intended; altered product or serial numbers; cosmetic damage

or exterior nish; accidents, abuse, neglect, re, water, lightning

or other acts of nature; use of products, equipment, systems,

utilities, services, parts, supplies, accessories, applications,

installations, repairs, external wiring or connectors not supplied

or authorized by SAMSUNG which damage this product or result

in service problems; incorrect electrical line voltage, uctuations

and surges; customer adjustments and failure to follow operating

instructions, cleaning, maintenance and environmental instruc-

tions that are covered and prescribed in the instruction book;

problems caused by pest infestations, and overheating by user.

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE

LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES

WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT

LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANT-

ABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL

APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED

ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUAR-

ANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION

WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON

SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF

REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR

OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE

OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF

THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND

EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY

OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND

AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE

PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG

AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING

THE FOREGOING, PURCHASER ASSUMES ALL RISK AND

LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER

AND PURCHASER’S PROPERTY AND TO OTHERS AND THEIR

PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY

TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED

DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED

WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN

THE ORIGINAL PURCHASER OF THIS PRODUCT IS NON-

TRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.

Some provinces or territories may or may not allow limitations on

how long an implied warranty lasts, or the exclusion or limitation

of incidental or consequential damages, so the above limitations

or exclusions may not apply to you. This warranty gives you

specic legal rights, and you may also have other rights which

vary from state to state.

To obtain warranty service, please contact SAMSUNG at:

1-800-SAMSUNG (726-7864) or

www.samsung.com/us/support

warranty (Canada)

SAMSUNG RANGE HOOD

Limited warranty to original purchaser

This SAMSUNG brand product, as supplied and distributed by

Samsung Electronics Canada, Inc. (SAMSUNG) and delivered

new, in the original carton to the original consumer purchaser, is

warranted by SAMSUNG against manufacturing defects in mate-

rials and workmanship for a limited warranty period of:

ONE (1) YEAR PARTS AND LABOR

This limited warranty begins on the original date of purchase,

and is valid only on products purchased and used in Canada. To

receive warranty service, the purchaser must contact SAMSUNG

for problem determination and service procedures. Warranty ser-

vice can only be performed by a SAMSUNG authorized service

center. The original dated bill of sale must be presented upon

request as proof of purchase to SAMSUNG or SAMSUNG’s

authorized service center.

SAMSUNG will repair or replace this product, at our option and

at no charge as stipulated herein, with new or reconditioned

parts or products if found to be defective during the limited

warranty period specied above. All replaced parts and prod-

ucts become the property of SAMSUNG and must be returned

to SAMSUNG. Replacement parts and products assume the

remaining original warranty, or ninety (90) days, whichever is

longer.

In-home service will be provided during the warranty labor

period subject to availability within the contiguous Canada.