AGA marvel MO24RFS2LS Mode d'emploi

Outdoor Refrigerator / Freezer

Réfrigérateur / Congélateurs

d'extérieur

Refrigeradores / Congeladors

exterior

MO24RF

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

ES Instrucciones de instalación, operación y mantenimiento

2

NOTE

!

CAUTION

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

is committed to building a quality product

in an environmentally friendly manner. Our processes are

tightly controlled and closely monitored. We have achieved

certications in ISO 9001 for quality assurance, ISO 14001

for environmental management, and OHSAS 18001 for oc-

cupational health and safety from Lloyd’s Register Quality

Assurance.

CONTENTS

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration ......................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the water supply ...................................................6

Optional ice-maker operation ..............................................7

Installing the anti-tip device .................................................8

Product dimensions ..........................................................10

Starting your appliance ..................................................12

Using your Electronic control ............................................12

Sleep mode ...................................................................12

Turning your appliance "ON" or "OFF" ..........................13

Adjusting the temperature .............................................13

Temperature mode ........................................................13

Control lock ................................................................14

Temperature sensor error codes ................................14

Alarms ...........................................................................14

Door ajar ..................................................................14

Power failure .............................................................15

Temperature alarm ....................................................15

Vacation mode ..................................................................15

Shelving congurations ....................................................16

Shelf removal ...................................................................17

Care and cleaning .............................................................18

Long term storage/winterization ...................................18

Stainless steel maintenance .............................................22

Energy saving tips ............................................................22

Obtaining service .............................................................23

Troubleshooting .................................................................24

Troubleshooting ice-maker ..............................................25

Warranty ...........................................................................26

!

WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

!

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

!

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

Death or serious injury could result if...

3

NOTE

!

CAUTION

XXXXXXXXXXXX

!

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

Warranty Registration

UNPACKING YOUR APPLIANCE

Online registration

available at

www.agamarvel.com

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.agamarvel.com.

The following information will

be required when registering

your appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the right

side near the top. (See gure 1).

Figure 1

!

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

!

WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

4

!

CAUTION

INSTALLING YOUR APPLIANCE

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

ensure your product performs to specications, the recom-

mended installation location temperature range is from 55

to 115°F (13 to 46°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unobstruct-

ed.

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex-

changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason

it is important this area not be obstructed and the grille

openings kept clean. AGA MARVEL does not recommend

the use of a custom made grille as air ow may be restrict-

ed. (See Figure 2).

Rear

Leveling

Legs

Figure 2

Front Leveling

Legs

Front Grille,

keep this area

open.

Leveling Legs

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is rmly positioned on the

oor and level from side to side and front to back. The over-

all height of your Marvel appliance may be adjusted be-

tween the minimum, 33

3

⁄4" (85.7 cm), by turning the leveling

leg in (CW ↷) and the maximum, 34

3

⁄4" (88.3 cm) by turning

the leveling leg out (CCW ↶).

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid

scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 5).

5

NOTE

Figure 3

Figure 4

Do not remove

ground prong

INSTALLING YOUR APPLIANCE

Front grille

Front grille screw

Figure 5

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

!

WARNING

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 6). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

Figure 6

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

6

Figure 7a

• Do not use any thread sealers on these water line t-

tings.

• Reverse osmosis, softened water, and de-ionized water

are not recommended as they will adversely affect the

quality of the ice.

Water

Supply

Line

service

loop

Figure 7

Back view of

ice machine

NOTE

!

CAUTION

Water line from water valve

to ice-maker

INSTALLING THE WATER SUPPLY

MODEL MO24RF WITH OPTIONAL ICE-MAKER KIT

An optional ice-maker kit (part number S42418151) is avail-

able for model MO24RF which includes all of the necessary

parts for installation. The kit can be obtained from Marvel

customer service by calling 800-223-3900.

Water Supply

Observe and follow all local building codes when installing

this appliance.

Use

1

⁄4" copper tubing for your water supply which is avail-

able at any local hardware or plumbing supply store. Bend

the

1

⁄4" copper tubing to suit your installation being sure not

to kink the tubing. Purchase enough copper tubing length

and coil it behind the unit to form a "service loop" which will

allow the appliance to be pulled out from the installation for

servicing or cleaning. Connect the copper tubing to the "top

side" of a cold water pipe to prevent the ice-maker from

plugging with sediment.

A shutoff valve is recommended on the water supply line to

ease servicing the appliance. NOTE: A SELF-PIERCING

TYPE VALVE IS NOT RECOMMENDED as they are prone

to clogging with sediment which will create pressure drop

reducing the water supply to the unit.

Connect the copper tubing water supply to the brass union

with the compression nut tting provided. (See Figure 7).

Water pressure must be at a minimum of 20 psi for proper

operation and a maximum of 120 psi.

Make certain all water connections are watertight after in-

stallation. Form the tubing so that it will not vibrate against

the cabinet body or kink when your appliance is set in posi-

tion.

Brass union for

1

⁄4" copper tubing

Connect water

supply here

7

NOTE

Ice-maker operation

• The unit must be installed level for proper ice-maker

operation.

• The shutoff arm wire must be down in its lowest posi-

tion for the ice-maker to operate. (See Figure 8).

• When the freezer section and ice-maker unit has suf-

ciently cooled, the ice-maker will harvest ice cubes

automatically.

• When the ice bucket is full, the ice-maker will automati-

cally shut off.

• You may manually stop the ice-maker by raising the

shut off arm to the locking position at the up most posi-

tion. (See Figure 8).

Arm down, ice-maker

will operate

Arm up, stops operation

Figure 8

OPTIONAL ICE-MAKER OPERATION

!

CAUTION

The water supply to the ice-maker must be turned on prior

to turning the ice-maker on. Failure to do so will cause

rapid dry cycling of the ice-maker mold heater resulting in

temperature control issues in the freezer compartment.

It is recommended the ice-maker is shut off when remov-

ing the bucket, or ice may be dispensed onto the freezer

compartment oor.

If the ice is not used regularly, it will clump together with

time. For best ice results, discard ice in the bin as required

and allow the ice-maker to make a new fresh batch of ice.

Shut-off the ice-maker by raising the shut-off arm before

removing the bucket.

8

!

CAUTION

NOTE

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

Step by step instructions for locating the po-

sition of the bracket:

1) Decide where you want to place the refrigerator / freezer.

Slide it into place, being careful not to damage the oor,

leaving 1" (2.5 cm) of clearance from the rear wall to allow

room for the anti-tip bracket.

2) Raise the rear leveling legs approximately

1

⁄4" (6 mm) to

allow engagement with the anti-tip bracket. Level the unit

by adjusting all the leveling legs as required. Turning the

leveling leg counterclockwise will raise the unit and clock-

wise will lower the unit.

3) Make sure the refrigerator / freezer is in the desired

location, then mark on the oor the rear and side corner

of the cabinet where the anti-tip bracket will be installed. If

the installation does not allow marking the rear corner of

the cabinet, then make temporary lines on the oor mark-

ing the front corner of the cabinet, excluding the door. Slide

the refrigerator / freezer out of the way. From the temporary

line extend the sidewall line back 21

1

⁄2" (54.6 cm) as shown

in Figure 10.

4) Align the anti-tip bracket to the marks on the oor so

the side of the bracket lines up with the side of the cabinet

mark, and the "V" notches on the anti-tip bracket line up

with the end of the 21

1

⁄2" (54.6 cm) line (Rear of cabinet

line).

5) Fasten the anti-tip bracket to the oor using the supplied

screw. (See Figure 10).

6) Slide the cabinet back into position, making sure the rear

cabinet leveling leg slides under the anti-tip bracket engag-

ing the slot.

Front of cabinet

Figure 9

21

1

⁄2"

(54.6 cm)

Anti-Tip

Bracket

Leveling Leg

Bottom View of

Refrigerator /

freezer

!

WARNING

If your refrigerator / freezer is not located under a

counter top (free standing), you must use an anti-tip

device installed as per these instructions. If the refrig-

erator / freezer is removed from its location for any

reason, make sure that the device is properly engaged

with the anti-tip bracket when you push the refrigerator

/ freezer back into the original location. If the device is

not properly engaged, there is a risk of the refrigerator

/ freezer tipping over, with the potential for property

damage or personal injury.

Floor Mount Installation

The anti-tip bracket is to be located on the oor in the left

or right rear corner of the refrigerator / freezer as shown in

Figure 9.

!

WARNING

• ALL APPLIANCES CAN TIP

RESULTING IN INJURY.

• INSTALL THE ANTI-TIP

BRACKET PACKED WITH

THE APPLIANCE.

• FOLLOW THE INSTRUC-

TIONS BELOW

Anti-Tip Device

If installing on a concrete oor, concrete fasteners are

required, (not included with the anti-tip kit).

Any nished ooring should be protected with appropriate

material to avoid damage when moving the unit.

9

NOTE

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

When the oor mounted anti-tip bracket is used the mini-

mum adjusted height of the cabinet is increased by

3

⁄8" (9 mm).

Figure 10a

"V" notches

in bracket

"V" notches

in bracket

Figure 10

21

1

⁄2"

(54.6 cm)

Front of cabinet line

Rear Leveling leg

Side of cabinet line

Rear of cabinet line

Screw

10

"A"

"B"

"C"

"D"

"E"

PRODUCT DIMENSIONS

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

MO24RFS

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

*

23

7

⁄8"

(60.7 cm)

33

3

⁄4" to 34

3

⁄4"

(85.7 to 88.3 cm)

23

⁄32"

(60.2 cm)

26

7

⁄32"

(66.6 cm)

46

13

⁄32"

(117.9 cm)

26

1

⁄4"

(66.7 cm)

DOOR STYLE

(S) Solid Door

Figure 11

Figure 11a

Figure 12

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

Not all recessed outlet boxes will work for this applica-

tion as they are too narrow, but a recessed outlet box

equivalent to Arlington #DVFR1W is recommended for

this application, (see Figure 12).

11

"F"

"D"

"E"

"H"

"J"

"G"

5

⁄8"

(1.6 cm)

PRODUCT DIMENSIONS

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

MO24RFS 115V/60Hz/15A

140 lbs

(63.6 kg)

!

WARNING

Floor mount Anti-tip Bracket must be installed for freestand-

ing applications. Not required for built in applications.

* Depth dimension of rough-in opening may vary depending

on each individual installation. To recess entire door "F" di-

mension plus 1" (2.5 cm) for thickness of power cord plug.

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

Figure 13

21

1

⁄2"

(54.6cm)

12

Power Failure

ALARM RESET

Compartment

select

REF

FRZ

Figure 14

Using your electronic control:

The sleep mode can be disabled if you prefer to have the

display on continuously. Press and hold the "Lock" key-

pad until the display goes past "Loc" and reads "nSL". To

enable the sleep mode, repeat the instruction, again going

past "Loc" until the display reads "SLP".

To wake the display press any keypad. A conrm tone will

sound, and the current storage compartment temperature

will be displayed.

Sleep mode:

If no keypads are pressed for 60 seconds, the display will

enter sleep mode to conserve power. The control panel will

go dark with the exception of the system status "OK" indi-

cator which will remain enabled. Alarm conditions will wake

the display, (see alarms on page 14).

Starting your appliance:

Plug the appliance power cord into a 115 volt wall outlet.

Your appliance is shipped from the factory in the "On" posi-

tion and will begin start-up of cooling as soon as power is

supplied. If the appliance does not start, conrm that the

wall outlet has power, and that the control is in the "On"

position, (See "Turning your appliance On and Off" below).

The control display is covered with a clear plastic lm. This

lm may be removed by carefully lifting the lm at a corner.

On initial power up, the control display will indicate a

"Power Failure" alarm. This is a normal condition as the ap-

pliance was powered-up at the factory for quality inspection

and then removed from power. A momentary press of the

"On/Off" keypad will reset this alarm condition. (See Alarms

section on page 14).

STARTING YOUR APPLIANCE

Figure 14a

Electronic control

Temp

Minus

keypad

Temp

Plus

keypad

On/Off

keypad

Display Area

Lock

keypad

System Status

indicators

NOTE

To make the following changes to the control settings

(turning the appliance ON/OFF, adjusting the tempera-

ture, and activating vacation mode), the control must

be awake.

Your product has an automatic defrost feature that utilizes

an electric heater element. Periodically during defrost you

may observe the following:

• Water dripping and running sounds as a result of the

frost melt

• Sizzling and popping sounds from water dripping on

the heater element

• A faint reddish glow in the freezer compartment from

the electric heater element

These are all “normal” operating characteristics related to

refrigeration product incorporating automatic defrost. They

do not represent any product fault or safety issue.

13

warmer respectively. When you have reached your desired

set-point temperature, press the "On/Off" keypad to accept,

or do nothing and the "Set" mode will time-out in 10-sec-

onds accepting the displayed temperature as the new

set-point.

The available set-point temperature range for your appli-

ance is -6°F (-21°C) to 6°F (-14°C) for the freezer com-

partment (ice-maker) and 34°F (1.2°C) to 42°F (5.7°C) for

the refrigerator compartment. If you attempt to adjust the

temperature outside of these ranges you will receive an

audible notication.

Freezer

compartment

selected

Refrigerator

compartment

selected

REF

FRZ

REF

FRZ

Temperatures can be set for each individual compartment

(refrigerator or freezer / ice-maker). To do so you must rst

select the compartment you want to set the temperature for.

You do so by pressing the refrigerator (REF) or freezer

(FRZ) button on the display. When pressed the LED light

will be illuminated for the respective display.

To change the set temperature for a particular compart-

ment, with the compartment enabled and out of sleep

mode, press the "-" or "+" keypads. "SET" will be indi-

cated on the user interface panel and the current set-point

temperature will display and ash. Subsequent presses of

the "-" or "+" keypads will adjust the temperature colder or

Adjusting the temperature:

When making temperature set-point changes, it may take

up to 24-hours for the stored contents to stabilize at your

new set-point temperature.

Factors that affect the storage compartment stabilized

temperature:

• Changes to temperature setting.

• Room temperature changes.

• Temperature of stored contents.

- Loading warm contents.

- Cold content load will delay the change to a warmer

set-point temperature.

- Warm content load will delay the change to a colder

set-point temperature.

• Usage, (number and duration of the door openings).

• Installation of the appliance in direct sunlight or next to

a heat source.

Turning your appliance ON and OFF:

If the appliance is "On", (and out of sleep mode) the tem-

perature will be shown in the display area of the control.

To turn the appliance "Off", press and hold the "On/Off"

keypad for 4-seconds. "OFF" will now be displayed on the

control.

To turn the appliance "On", press and hold the "On/Off"

keypad for 4-seconds.

USING YOUR ELECTRONIC CONTROL

Temperature mode:

The temperature mode is preset from the factory in Fahren-

heit (°F) but you have the option to change it to Centigrade

(°C). To change the mode, press and hold the "-" keypad,

while pressing the "+" keypad, then release the "-" keypad.

The temperature will now be displayed in Centigrade (°C).

Repeat the procedure to change the temperature mode

back to Fahrenheit (°F).

NOTE

Loading warm contents may trigger a temperature alarm,

see temperature alarm page 15. Depending on the quantity

and/or weight of warm contents, it may take 48 hours for

the compartment temperature to stabilize.

14

Temperature Sensor Error Codes

Sensor Displayed Code Error Description Action to Take

Refrigerator

Temperature

Sensor

Failed temperature sensor in the

refrigerator compartment. Can lead to

unwanted storage temperatures and/or

spoiled perishable goods.

Call service to have the

temperature sensor replaced and

remove all perishable goods from com-

partment to prevent spoilage.

Freezer

Temperature

Sensor

Failed temperature sensor in the

freezer compartment. Can lead to

unwanted storage temperatures and/or

spoiled perishable goods.

Call service to have the

temperature sensor replaced and

remove all perishable goods from com-

partment to prevent spoilage.

Defrost Sensor

Failed defrost temperature sensor.

Causes unit to not defrost properly and

can create large frost build-up. Can lead

to water damage to the unit and sur-

rounding oor.

Unplug the power cord

immediately and call service to have

the defrost sensor replaced.

Door Ajar

ALARM RESET

USING YOUR ELECTRONIC CONTROL

Alarms:

The control will alert you to conditions that could adversely

affect the performance of the appliance.

• Door ajar - If the door is open, or not closed prop-

erly, for more than 5-minutes the System Status OK

indicator will turn-off, the "Door Ajar" indicator will ash,

and a tone will sound every 60 seconds. Additionally,

an "ALARM RESET" indicator will be displayed below

the "On/Off" keypad.

The temperature sensors are monitored continuously. Any

OPEN or SHORTED circuit condition will initiate an

ERROR CODE as listed below:

Temperature Sensor Error Codes

Control lock:

The control panel can be locked to avoid unintentional

changes. To lock the control, press and hold the "Lock" key-

pad until the display reads "Loc" then immediately release

your nger from the keypad. The lock icon will ash 3-times

and then continuously illuminate. When the control panel is

locked, only the Lock keypad, System Status OK indicator

, and the Alarm indicator are active. To un-lock the control

panel, repeat this instruction until the display reads "nLc"

then immediately release your nger from the keypad.

NOTE

If the control lock is active (illuminated lock icon) the

control will have to be unlocked before using the

keypad to reset an alarm condition. See page 14

(Control Lock) for instructions for unlocking the control.

This alarm condition can be reset by closing the door or

momentarily pressing the "On/Off" keypad, (i.e.-if you

are cleaning the storage compartment, etc.). The alarm

will recur in 5-minutes if the alarm condition persists.

NOTE

The audible alarm can be muted, for each occurrence,

by pressing the lock keypad.

15

ALARM RESET

Power Failure

ALARM RESET

Temp

NOTE

Door Ajar

Temp

• Power failure - If power to the appliance is inter-

rupted the System Status indicator will turn-off and

the "Power Failure" indicator will ash. Additionally, an

"ALARM RESET" indicator will be displayed below the

"On/Off" keypad. No audible tone will sound. This alarm

condition can be reset by momentarily pressing the

"On/Off" keypad. If this alarm occurs, it is recommend-

ed that you check the condition of any perishables,

even if the appliance is operating normally and the tem-

perature has recovered, as prolonged power outages

could result in excessive temperature excursions which

may spoil perishables.

• Temperature alarm - If the storage compart-

ment temperature deviates excessively from your

set-point temperature for an extended period of time,

the "TEMP" indicator will ash, and an audible tone

will sound every 60 seconds. Additionally, an "ALARM

RESET" indicator will be displayed below the "ON/

OFF" keypad.

Multiple alarms are possible, i.e.- "Door Ajar" for a pro-

longed period may trigger a "Temp" alarm, in which case

both "Door Ajar" and "Temp" indicators will activate.

Vacation mode:

This operating mode can be used to save energy during

high cost energy periods, or when you won't be using your

appliance for an extended period of time by disabling the

lights, alarm tones, and keypad entry tones. Vacation mode

also serves as a Sabbath mode, disabling functions and

its controls in accordance with the weekly Sabbath and

religious holidays observed within the Orthodox Jewish

community. When used as Sabbath mode, you may open

or close the door at any time to access contents without

concern of directly turning on or off any lights, digital read-

outs, solenoids, fans, valves, compressor, icons, tones, or

alarms.

When activated, the display, alarm indicators and tones,

keypad touch tones, interior lights, and all options are dis-

abled. All keypad functions are disabled, with the exception

of the "On/Off" keypad which is required to exit Vacation-

mode. Storage compartment temperatures are monitored

and controlled at the settings prior to entering Vacation

mode.

To enter Vacation Mode (with the control out of sleep

mode), press and hold the "On/Off" keypad until the display

goes past "OFF" and reads "VAC". The display will ash

"VAC" 3-times to acknowledge your request, then will

display "VAC" continuously until Vacation mode is exited.

A power outage will not exit Vacation mode, exiting can

only be accomplished manually. To exit Vacation mode and

return to normal operation, press and hold the "On/Off"

keypad until the control displays the temperature.

USING YOUR ELECTRONIC CONTROL

NOTE

The audible alarm can be muted, for each occurrence,

by pressing the lock keypad.

This alarm condition can be reset by momentarily pressing

the "On/Off" keypad. If this alarm occurs it is recommended

that you check the condition of your stored contents, even

though the appliance is operating normally and the temper-

ature has recovered, as prolonged temperature excursions

could spoil perishables.

NOTE

After a high temperature alarm condition, check all perish-

ables to ensure they are safe for consumption.

The temperature alarm may occur as a result of high usage

or introduction of warm contents to the storage compart-

ment. If the temperature alarm continues to occur, your unit

may require service.

16

SHELVING CONFIGURATIONS

Refrigerator / Freezer

24" (61 cm) wide see Figure 15:

Refrigerator:

(2) Half width cantilever adjustable shelf.

see Figure 16

(1) Full width xed position glass shelf

(1) Roller glide clear crisper drawer

Freezer:

(1) Fixed position metal shelf, see Figure 17.

Figure 15

To remove the crisper :

Pull out until it stops. Lift up on the front of the pan, and

remove it from the frame.

Figure 16

Freezer

compartment

Figure 17

Freezer shelf

Figure 18

17

SHELF REMOVAL

To Add or Remove a Shelf

Remove stored product from the shelf. Do not try to remove

a loaded shelf from the appliance. Grasp the shelf front with

both hands, rotate the front upward and lift out. (See Figure

19a). To install a shelf insert the shelf in the appliance and

insert the top hooks into the shelf support slots and drop

the shelf down so the hooks drop over the bottom of the

slots.

Make sure your cantilever shelf is secure on the shelf sup-

ports by pressing down on the shelf before loading.

!

CAUTION

!

CAUTION

Never try to move a loaded shelf, remove everything from

the shelf before moving. Use both hands when moving the

shelf.

Grasp the shelf

by the front with both

hands and rotate the

front of the shelf up,

then lift the shelf up

and remove the shelf

from the shelf ladders.

Figure 19

Figure 19a

18

!

CAUTION

CARE AND CLEANING

Front Grille

Be sure that nothing obstructs the required air ow open-

ings in front of the cabinet. At least once or twice a year,

brush or vacuum lint and dirt from the front grille area (see

page 4).

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

Cabinet

The painted cabinet can be washed with either a mild soap

and water and thoroughly rinsed with clear water. NEVER

use abrasive scouring cleaners.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

Care of Appliance

1. Avoid leaning on the door, you may bend the door

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or mop-

ping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as

needed.

4. Periodically check and/or clean the front grille as

needed.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as pos-

sible. Minimize the number of door openings while the

power is off so as not to adversely affect the appliance's

temperature.

Light assembly replacement

All models use LED lamps to illuminate the interior of the

appliance. This component is very reliable, but should one

fail, contact a qualied service technician for replacement

of the LED.

Outdoor Product Long-Term Storage / Winter-

ization: (MO24RF, refrigerator freezer):

1. Time to Winterize, when the daily low ambient tempera-

ture is at or below 38°F (3.3°C).

!

CAUTION

Operation of the unit at ambient temperatures below the

recommended Winterization temperature will void your war-

ranty.

2. Turn unit off, (see page 13)

3. Remove all contents.

4. If necessary, move the unit so you can gain access to

the rear of the product.

5. Unplug the unit from the power outlet.

6. It is also recommended that the power to the outlet be

turned-off if the circuit is not required for other items

during the Winter season.

7. When cleaning unit pay particular attention to any

cracks and crevices that may have accumulated dirt

and debris.

8. Remove the front toe-grille, (see Figure 20), and use a

brush and vacuum to clean dirt and debris from be-

neath the unit.

9. Thoroughly clean the toe-grille and re-install on the

unit. (See Figure 20).

10. Remove the rear access cover, (see Figure 21), and

use a brush and vacuum to clean dirt and debris from

the machine compartment.

11. Thoroughly clean the rear access cover and re-install

on the unit.

12. Wipe down all interior surfaces with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals which could cause staining. Do

not use any abrasive cleaners or scouring pads.

13. Leave the door open and allow to completely dry out

before closing the door.

14. Thoroughly clean the door gasket with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals.

15. Thoroughly clean the exterior with a cleaner approved

for stainless steel. Do not use any abrasive cleaners or

scouring pads. See "Stainless Steel Maintenance" on

page 22.

16. Any mounting hardware / fasteners that are showing

signs of corrosion should be replaced.

17. Once the exterior has been thoroughly cleaned, you

may want to apply a coating of car wax to help protect

against spotting from moisture, dirt, and debris that

may accumulate on the surfaces during the Winteriza-

tion period.

• If the plastic defrost drain pan located under the

compressor contains water, use a sponge to

remove as much water as possible.

19

CARE AND CLEANING

Start-Up After Long-Term Storage:

1. If stored outside, it is recommended that the unit again

be thoroughly inspected per the storage instructions

above to address any dirt or debris from the weather

and/or animals/insects.

2. Connect the unit to electrical power.

3. Turn unit on and conrm your desired control settings.

4. Allow 24-hrs for the unit to stabilize before loading

contents.

Figure 20

Grille

Spacer

Clean out

behind

grille

Figure 21

Soak up

water from

plastic drain

pan if

necessary

Clean out

debris

Remove screws

around perimeter

of access cover.

18. Do not place a cover on the unit, as this can trap con-

densation.

After completion of the above, you may choose to store the

unit indoors, although this is not required.

Remove screw from

each end of grille

Access cover

20

!

CAUTION

Operation of the unit at ambient temperatures below the

recommended Winterization temperature will void your war-

ranty.

2. Raise the bail arm of the ice maker ( see Figure 8 on

page 7) to stop ice production.

3. Turn the water supply to the unit off.

4. If necessary, move the unit so you can gain access to

the rear of the product.

5. Disconnect the water supply line from the water ll

valve located on the back of the unit, (see page 6).

6. Be sure the exterior water supply line is drained or

blown out to prevent freezing and cracking of the sup-

ply line.

7. We recommend a cap be placed on the water supply

line to prevent dirt and insects from plugging the line.

8. Empty the ice bucket and replace the ice bucket in unit.

9. Lower the ice maker bail arm to allow the unit to oper-

ate until ice is dispensed from ice maker to empty the

ice maker mold.

10. Raise the bail arm and remove the ice bucket and

clean thoroughly with warm water and dish soap.

11. Turn unit off to defrost ice storage compartment, see

page 12).

12. Unplug the unit from the power outlet.

13. It is also recommended that the power to the outlet is

turned-off if the circuit is not required for other items

during the winter season.

14. When cleaning the unit pay particular attention to any

cracks and crevices that may have accumulated dirt

and debris.

15. Remove the front toe-grille, (see Figure 22), and use a

brush and vacuum to clean dirt and debris from be-

neath the unit.

16. Thoroughly clean the toe-grille and re-install on the

unit. (See Figure 22).

17. Remove the solenoid cover and 3 screws. (see Figure

23). Remove the rear access cover, (see Figure 23),

and use a brush and vacuum to clean dirt and debris

from the machine compartment.

18. Disconnect the plastic water line from the bottom of the

solenoid valve (see Figure 23a) and drain. Reconnect

the water line.

Outdoor Product Long-Term Storage / Winter-

ization: (MO24RF, with optional ice maker):

1. Time to Winterize, when the daily low ambient tempera-

ture is at or below 38°F (3.3°C).

CARE AND CLEANING

Figure 22

Grille

Spacer

Clean out

behind

grille

Remove screw from

each end of grille

19. Thoroughly clean the rear access cover and re-install

on the unit.

20. Wipe down all interior surfaces with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals which could cause staining. Do

not use any abrasive cleaners or scouring pads.

21. Leave the door open and allow to completely dry out

before closing the door.

22. Thoroughly clean the door gasket with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals.

23. Thoroughly clean the exterior with a cleaner approved

for stainless steel. Do not use any abrasive cleaners or

scouring pads. See "Stainless Steel Maintenance" on

page 22.

24. Any mounting hardware / fasteners that are showing

signs of corrosion should be replaced.

25. Once the exterior has been thoroughly cleaned, you

may want to apply a coating of car wax to help protect

against spotting from moisture, dirt, and debris that

may accumulate on the surfaces during the Winteriza-

tion period.

• If the plastic defrost drain pan located under the

compressor contains water, use a sponge to

remove as much water as possible.

La page charge ...

AGA marvel MO24RFS2LS Mode d'emploi

Ce manuel convient également à

AGA marvel MO24RFS2LS Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents