Frigidaire 970L48022A0 Guide d'installation

Marque: Frigidaire

Modèle: 970L48022A0

Taper: Guide d'installation

installation instructions

instructions d_lnstallation

English / Franc;ais

P/N 137453700 (1105)

Sears Brands Management Corporation

Hoffman Estates, IL 60179 U.S.A.

www.kenmore.com

www.sea rs.com

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2C3

WWW.sea rs.ca

Important Safety Instructions

Please read all instructions before using this washer.

Recognize safety symbols, words and

labels

Safety items throughout this manual are labeled with

a WARNING or CAUTION based on the risk type as

described below:

Definitions

Z_ This is the safety alert symbol. It is used to alert you

to potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible injury or

death.

DANGER indicates an imminently hazardous situation

which, if not avoided, will ....

WARNING

which,ifnotavoided,couldresultindeathorserious

injury.

CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

IMPORTANT indicates installation, operation or

maintenance information which is important but not

hazard-related.

Table of Contents

Important Safety Instructions ............................................ 2-3

Installation Requirements ................................................... 4-5

Washer Dimensions ................................................................ 6

Unpacking Washer ............................................................. 7-8

Installation Instructions ..................................................... 9-10

Accessories ............................................................................. 11

Notes ...................................................................................... 12

Francois .................................................................................. 13

Installation Checklist

Shipping Hardware

[] Foam shipping support (under wash tub)

removed and stored

[] Shipping baits and spacers removed from rear

of appliance and stored

[] Hole plugs (shipped in bag in drum) installed in

holes in backsheet

Leveling

[] Washer is level, side-to-side and front-to-back

[] Cabinet is setting solid on aii corners

Water Supply

[] Rubber washers (shipped in drum) are installed

in NEW inlet hoses (shipped in drum)

[] HOT supply is connected to HOT inlet and

COLD supply is connected to COLD inlet

[] HOT and COLD water supply turned on

[] No leaks present at water supply connections

or appliance inlet connections -

recheck in 24 hours

[:)rain

[] Stand pipe or wall drain height minimum 24"

[] Drain hose snapped in "U" channel (shipped in

drum)

[] Drain hose secured in place with cable tie

(shipped in drum)

Electrical Power

[] House power turned on

[] Washer plugged in

Final Checks

[] Installation Instructions and Use and Care

Guide have been read thoroughly

[] Door Jacks and water enters drum when cycle

starts

important Safety Requirements

The electrical service to the washer must conform with

local codes and ordinances and the latest edition of the

National Electrical Code, ANSIiNFPA 70, or in Canada,

z% RNING ................................................................................................................................................................

............ SUFFOcATIoN HAZARD ....

Destroy the carton and plastic bags after the washer

is unpacked. Children might use them for play. Cartons

covered with rugs, bedspreads, or plastic sheets can

become airtight chambers causing suffocation. Place

all materials in a garbage container or make materials

inaccessible to cMidren.

EXCESSI?EwEIBH?HAZARD

To avoid back or other injury , have more than one person

move or lift the washer.

Z%RNING

_:_ WARNING

u ,,

FiRE HAZARD

For your safety the information in this manual must be

followed to minimize the risk of fire or explosion or to

prevent property damage, personal injury or Jossof life.

Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

iMPORTANT

The instructions in this manual and ail other literature

included with this washer are not meant to cover every

possible condition and situation that may occur. Good

safe practice and caution MUST be applied when

installing, operating and maintaining any appliance.

Maximum benefits and enjoyment are achieved when

all the Safety and Operating Instructions are understood

and practiced as a routine with your laundering tasks.

Save these instructions

for future reference.

Do not stack a dryer on top of washer already installed

on pedestal. Do not stack washer on top of dryer. Do not

stack washer on top of another washer.

Pre-lnstallation

Tools and materials needed for installation:

OR OR OR

Universal wrench

supplied with

washer

Adjustable 3/8" or 10 mm Ratchet and

wrench box wrench socket set

Requirements

AND

Adjustable

pliers

AND

Carpenter's level

Installation Requirements

Electrical system requirements

CIRCUIT - Individual, properly polarized and grounded 15

amp. branch circuit fused with 15 amp. time delay fuse

or circuit breaker.

POWER SUPPLY - 2 wire, with ground, !20 volt single

phase, 60 Hz, Alternating Current.

Because of potentially inconsistent voltage capabilities,

the use of this washer with power created by gas

powered generators, solar powered generators, wind

powered generators or any other generator other than

the local utility company is not recommended.

Since your washer is equipped with a power supply

cord having an equipment-grounding conductor

and a grounding plug, the plug MUST be plugged

into an appropriate, copper wired receptacle that is

properly installed and grounded in accordance with

all local codes and ordinances or in the absence

of local codes, with the National Electrical Codes,

ANSI/NFPA 70 (latest edition). If in doubt, caii

a licensed electrician. DO NOT cut off or alter

the grounding prong on the power supply cord. In

situations where a two-slot receptacle is present_

it is the owner's responsibility to have a licensed

electrician replace it with a properly grounded three

prong grounding type receptacle.

OUTLET RECEPTACLE - Properly grounded 3-prong

receptacle to be located so the power supply cord is

accessible when the washer is in an installed position.

wal

Do not, under

any circumstances,

cut, remove,

or bypassthe

grounding prong.

Powercord with

3-prong grounded plug

......NoTE ........

GFI (Ground Fault Interrupter)receptacle is not required.

Ground requirements

ELECTRICAL SHOCK HAZARD

Improper connection of the equipment grounding

conductor can result in a risk of electrical shock. Check

with a licensed electrician if you are in doubt as to

....whether the appliance is proper!y grounded. ...................................................................................

The washer MUST be grounded. In the event of

malfunction or breakdown, grounding will reduce the

risk of electrical shock by providing a path of least

resistance for electrical current.

Water supply requirements

Hot and cold water faucets MUST be installed within 42

inches (107 cm) of your washer's water inlet. The faucets

MUST be 3/4 inch (1.9 cm) and have threading for laundry

hose connection. Water pressure MUST be between 30

and 120 psi. Pressure difference between hot and cold

cannot be more than 10 psi. Your water department can

advise you of your water pressure.

Drain system requirements

1 Drain capable of eliminating 17 gals (64.3 L) per

minute.

2 A standpipe diameter of 1-1/4 in. (3.18 cm)

minimum.

3 The standpipe height above the floor should be:

Minimum height: 24 in. (61 cm)

Maximum height: 96 in. (244 cm)

96"

(244cm)

max.

(61 cm)

rain.

Drain hose attached to the washer can reach a 74 in.

(188 cm) high standpipe. For higher standpipe, use hose

P/N 137098000, available from Sears Parts & Repair.

Call ]-800-4-MY-HOME t.....................................................................................................................................................................................................

Installation Requirements

Clearance requirements

DO NOT INSTALL YOUR WASHER:

| Inan area exposed to drippingwater or outside

weather conditions. The ambient temperature

o o

should never be below 60 F (15.6 C) to maximize

detergent effectiveness.

2 Inan area (garage or garage-type building)

where gasoline or other flammables (including

automobiles)arekeptorstored.

3 On carpet. Floor MUST be solid with a maximum

slope of ] inch (2.5 cm). To minimize vibration

or movemen h reinforcement of the floor may be

necessary.

Installation in a Recess or Closet

If washer and dryer are installed in the same closet_ door

ventilation is required: A minimum of 120 square inches

(774.2 cm 2) of opening_ equally divided at the top and

bottom of the door_ is required. Louvered openings should

be located 3 inches (7.6 cm) from bottom and top of door.

Air openings are required to be unobstructed when a door

is installed. A Iouvered door with equivalent air openings

for the full length of the door is acceptable.

MINIMUM INSTALLATION CLEARANCES- Inches (cm)

SIDES REAR TOP FRONT

Alcove O" (0 cm) O" (0 cm) _ O" (0 cm) n/a

Under-

0" (0 cm) 0" (0 crn) _" 0" (0 cm) n/a

Counter

Closet 0" (0 cm) 0" (0 crn) _" 0" (0 cm) 1" (2.5 cm)

0" ------I_0 I_-----

(0cm) :0

"i ......

0" t

(0cm)

iiTOom)

---1--

60 sq. in.

(387.1cm 2)

______

---_--

60 sq. in.

(387.1cm 2)

closet door

Washer Dimensions

49.5" (126 cm)

to clear open door I__

freestanc

washer on floor

floor line

27.8" (70.5 cm)

to front of closed door

washer mounted on 'l

optional pedestal

floor line _-

water supply

connection on

rear of unit I

2ZO"

(68.5 cm)

36.0"

(91.5 era)

drain hose on

rear of unlt 3

5t.25"

(130 cm)

50.8" (t29 cm) _.

to clear open door ..q 29.75" (75.5 cm)

to front of closed door

floor lira

m l m

m m l

m J

71.5"

(182 cm)

1Hot and cold inlet hose length on washer approximately 43 inches (109 cm).

2Power supply cord length on washer approximately 60 inches (152.5 cm).

3Draln hose length on washer approximately 52 inches (132 cm).

4power supply cord length on gas dryer approximately 60 inches (152.5 cm).

water supply

connection on

rear of unit I

gas supply

pipe on rear

of gas unit

37"

(94 cm)

27.0" ---_

(68.5 cm)

electrical

supply on

rear of unlt 4

centerllne

height for

drain hose on

rear of unlt 3

39"

(99 cm)

Unpacking Washer

Removing foam packaging

i WARNING

, ............................................................................SUFFOC_ION¸¸¸NAZARD........................................................................................

Destroy the carton and plastic bags after the washer

is unpacked. Children might use them for play. Cartons

covered with rugs, bedspreads, or plastic sheets can

become airtight chambers causing suffocation. Place

all materials in a garbage container or make materials

inaccessible to children.

| Temporarily remove door tape.

2 Open washer door and remove everything from the

drum.

3 Close door and reappiy door tape.

4 Using a rug, blanket or piece of cardboard to protect

the floor, carefully lay the washer on its back.

CAUTION

Exc ZARD

To avoid back or other injury, have more than one person

move or lift the washer.

Remove styrofoam base and shipping plug and set

them aside.

Carefully return the washer to an upright position.

Carefully move the washer to within 4 feet (1 m) of

its final location.

Save styrofoam base and shipping plug for use to help

preven was he damag dur!n an f u moves: .....................................................

Unpacking Washer

Removing shipping hardware

m 2 P CLAMPS

NOTE............................................................................................................................

Rubber expansion material on spacers

may need time to relax before they can

be easily pulled through shipping hole. You

may have to exert some force to pull out if

spacer material has not yet fully relaxed.

/ x4 _x4

• 4 SPACERS

Remove all of the following:

0 4 BOLTS • 4 SPACERS

2 P CLAMPS

Save all shipping bolts and spacers for future use. If the

washer is to be transported at a later date, the shipping

hardware must be reinstalled to help prevent shipping

installing hole plugs

Ax4

,& 4-HOLE PLUGS

(IN BAG)

Locate 4 hole plugs in the small bag supplied

with washer instruction guides. Insert them in the

holes in washer back panel.

Installation instructions

Leveling your washer

Excessive noise and vibration can be prevented by

properly leveling the washer.

| For free standing installation and with the washer

within 4 feet (1 m) of its final location, place a level

on top of the washer.

2 Use adjustable pliers to adjust the leveling legs so

the washer is level front-to-rear and side-to-side,

and stable corner-to-corner.

3 Press down on alternate corners and sides and feel

for the slightest movement. Adjust the appropriate

legCs) so the washer sits solidly on the floor on ALL

four legs. Keep the leveling leg extension at a

minimum for best performance of the washer.

For pedestal installations, see additional installation

instructions included with the pedestal.

Connecting inlet water

| Run some water from the hot and cold faucets to

flush the water lines and remove particles that might

dog the water valve screens and to determine which

faucet is hot and which is cold supply.

2 Remove the inlet hoses and rubber washers from the

plastic bag located in the drum of the washer and

install the rubber washers in each end of the inlet

hoses.

RUBBER WASHERS "_._2 ,,

MUST BE PRESENT

USEONLY

NI:W HOSES

3 Connect the HOT inlet hose to the HOT inlet

connection on the washer and the COLD inlet

hose to the COLD inlet connection on the washen

Tighten by hand until snug. Then tighten each supply

connection another 2/3 turn with pliers. Do not cross

thread or over-tlghten these connections.

4 Connect the HOT inlet hose to the HOT water supply

and the COLD inlet hose to the COLD water supply.

Tighten by hand until snug. Then tighten each supply

connection another 2/3 turn with pliers. Do not

bend, kink or pinch water inlet hoses.

5 Turn on the water and check for leaks.

HOT

COLD

Installation instructions

Connecting drain and electrical

| Snap one end of the drain hose hanger (shipped

in washer drum) onto the drain hose. Continue

wrapping it around the hanger and snap it in place.

2 Place the hook end of the drain hose in the drain

opening. Secure the drain hose with the cable

tie (provided in the enclosure package) to the

standpipe, inlet hose, laundry tub, etc. so the hose

does not pull out from the force of the water.

Check to ensure the power is off at a circuit breaker/

fuse box before plugging the power cord into an outlet.

3 Hug the power cord into a grounded outlet.

Do not, under

any circumstances, |

cut, remove, /

or bypass the |

grounding prong. J

Power cOrdwit

3,prong grounded plug

CABLE Till:

4 Turn on the power at a circuit breaker/fuse box.

,5 Carefully slide the washer to its final position.

Recheck for level and rock corners for stability.

Remove and discard door tape.

6 Read the Use & Care Guide provided with the

washer. It contains valuable and helpful information

that will save you time and money.

7 If you have any questions during initial operation,

please review the "Avoid Service Checklist" in your

Use & Care Guide before calling for service.

8 Place these instructions in a location near the washer

for future reference.

A wiring diagram and technical data sheet are located

under the washer top panel, on top of the detergent

d!spenser hous!ng" .....................................................................................................................................................................................................................................................

Accessories

CAUTION.............................................................................................................................................................................................

White Pedestal - P/N CFPWD15W

Black Pedestal- P/N CFPWD15B use accessories manufaciured by ior

Blue Pedestal- P/N CFPWD15N approved by)the manufacturer could result in

Silver Pedestal- P/N CFPWD15A personal injury, property damage or damage to the

A storage pedestal accessory, specifically designed for this washer washer.

may be used to elevate the washer for ease of use. This pedestal

wiii add about 15.25" (39 cm) to the height of your unit for a total

height of 51.25" (130 cm).

*Other colors may be available. Contact the source where you

purchased your washer.

DRYER STACKING KIT

P/N STACKIT4X

Depending on the model you purchased, a kit for stacking a

matching dryer on top of this washer may have been included in

the initial purchase of your dryer. If your model did not include a

stacking kit or you desire another stacking kit, you may order one.

DRAIN HOSE EXTENSION KIT

P/N 137098000

In order to reach standpipe heights or distances beyond the reach

of the drain hose supplied, order the DRAIN HOSE EXTENSION

I<IT.

MOBILE HOME INSTALLATION KIT

P/N 137067200

Installation in a mobile home requires the use of a MOBILE HOME

INSTALLATION KIT.

UNIVERSAL APPLIANCE WRENCH

P/N 137019200

A UNIVERSAL APPLIANCE WRENCH is available to aid in dryer/

washer/pedestal feet adjustment.

TOUCH UP PAINT PENS*

White Touch Up Pen - P/N 5304468812

Black Touch Up Pen - P/N 5304458932

Blue Touch Up Pen - P/N 5304471229

Silver Touch Up Pen - P/N 5304471228

*Other colors may be available. Contact the source where you

purchased your washer.

Replacement parts:

If replacements parts are needed for your washer, contact

the source where you purchased your washer or refer to

your Use and Care Guide for more information.

w R ,No...........................................................................................................

ELECTRICAL SHOCK HAZARD

Label all wires prior to disconnection when servicing

controls. Wiring errors can cause improper and

dangerous operation. Verify proper operation after

servicing. ...................................................................................................................................................................................................................................................................................................

Notes

installation instructions

instructions d_lnstallation

English / Franc;ais

Sears Brands Management Corporation

Hofl:man Estates, IL 60179 U.S.A.

www.kenmore.com

www.sea rs.com

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2C3

WWW.sea rs.ca

Mesures de S curit Importantes

AVERTISSEMENT..........

Veuillez lire ces instructions au complet avant d'utiliser la

laveuse.

Sachez reconnaffre les symbobs, les aver-

tissements et les _tiquettes de s_curit_.

Les mesures de s_curit_ pr_sent_es dans ce guide sont

identifiSes par ie mot AVERTISSEMENT ou ATTENTION

selon le type de risque pr_sent_ ci-dessous.

D_finitions

Z_ Voici ie symbole d'avertissement concernant ia s_curit_.

IJ est utilis_ pour vous avertir des risques de bJessures

potentieis. Respectez tousles messages qui suivent ce

symbole afin de pr_venir les blessures ou la mort.

La mention DANGER indique un risque imminent qui

AvERTI$$EMENT ..................................................................................................................

L_meniionAVERTiSSEMENTindiqueunesiiuaiion

potentiellement dangereuse qui, si elle n'est pas _vit_e,

La mention ATTENTION signale la presence d'une

situation potentielJement dangereuse susceptible de

causer des blessures mineures ou moyennement graves si

elle n'est pas _vit_e.

IMPORTANT- Cette mention prScSde des renseignements

importants relafifs 6 I'installafion, au foncfionnement ou

6 l'entrefien. Toutefois, ceux-ci n'impliquent aucune notion

Table des Mati6res

Mesures de S_curit_ Importantes .................................. 14-15

Exigences d'lnstailation .................................................. 16-17

Dimensions de Laveuse ........................................................ 18

D_baiiage de ia Laveuse ............................................... 19-20

Instructions d'lnstallation ............................................... 21-22

Accessoires ............................................................................. 23

Liste de v@rification

d'installation

Materiel d'exp_dition

[] Le support d'exp_dition en mousse (sous la cuve

de lavage) a _t_ enlev_ et remis_

[] Les boulons d'exp_dition situ_s & I'arri_re de

i'appareii ont 8t8 enievSs et remis_s

[] Les bouchons (incius dans ie sac situ_ dans ia

cuve) ont 8t8 insSrSs dans les trous situSs dans

ia paroi arriSre de ia iaveuse

Mise _ niveau

[] La Javeuse est au niveau Jat_ralement et de

J'avant vers J'arri_re

[] Les quatre coins de Ja caisse reposent

fermement sur Je plancher

Alimentation en eau

[] Le tuyau d'entr_e d'eau CHAUDE est raccord_

au robinet d'eau CHAUDE et le tuyau d'entr_e

d'eau FROIDE est raccord_ au robinet d'eau

FROIDE

[] Les robinets d'eau CHAUDE et d'eau FROIDE

sont ouverts

[] kes raccords d'alimentation en eau ou les

raccords d'arrlv_e d_eau de I'apparell ne

pr_sentent aucune fuite -

refaites une v_rification 24 heures plus tard

Tuyau de vidange

[] La colonne montante ou Ie drain de mur est &

une hauteur d'au moins 61 cm (24 po)

[] Le tuyau de vidange est fiX_ dans le canal en

_( U )_(incius dans ia cuve)

[] Le tuyau de vidange est fix_ avec I'attache

(incluse dans la cuve)

Alimentation en _lectricit_

[] Le syst_me _lectrique de la maison est sous

tension

[] ka laveuse est branch_e

V_rifications finales

[] Vous avez lu enti_rement les instructions

d installation et le Guide d'Utilisation et

d'Entretien

[] La porte se verrouille et I'eau entre dans la cuve

Iorsqu'un cycle d_marre

Mesures de S_curit_ importantes

L'instailation _iectrique de la laveuse dolt _tre conforme

aux codes et aux r_cjiements Iocaux ainsi qu'& la toute

derni&re _dition du National Electrical Code (ANSI/

NFPA 70), ou au Canada, au Code canadien de

......._ AvERTI$$EMENT ...................................................................................................................

RISQUE D;_TOuFFEMENT

D_truisez le carton d'emballacje et les sacs en plasfique

apr&s avoir d_ball_ I'appareil. Les enfants pourraient

les ufiNser pour jouer. Le carton recouvert de tapis I les

couvertures et les feuilles de plasfique peuvenf &fre

_tanches 6 Fair et provoquer la suffocation. D_posez tous

les mat_riaux d'emballacje duns un conteneur 6 d_chets ou

_e rt _ _ _!_ _c_:............................

.......ATTENTION.......................................................................................................................................................

DANGERDEP61DsEXCESSIF

Pour_iter lesblessuresaudosoud'autrestypesde

blessure, demandez I'aide d'autres personnes pour

AvERTI$$EMENT

RISQUE D;INcENDIE

Ne superposez pus une s_cheuse sur une laveuse d_j6

instali_esurunsocle.Nesuperpose_pusunelaveusesur

une s_cheuse. Ne superposez pus une laveuse sur une

autrelaveuse.

.........AVERTISSEMENT..........

RISQUE D'INCENDIE

Pour votre securite, I'information contenue dans ces

instructions doit etre suivie afin de reduire les risques

d'incendie ou d'explosion ou pour pr_venir les dommacjes

materiels, les blessures ou la mort. Vous ne devez ni

entreposer, nJ utiliser d'essence ou d'autres vapeurs ou

liquides inflammables & proxJmJt_ de cet appareil ou de

tout autre appareil electromenacjer.

iMPORTANT

Les instructions comprises duns ce guide et route autre

documentation fournie avec cet appareil ne sont pus

con_:ues pour couvrir toutes les _ventualit_s ou situations

qui pourraient survenir. Vous DEVEZ faire preuve de bon

sens et de prudence durant I'installation, I'utilisation et

I'entretien de tout appareil m_nacjer.

Vous tirerez le maximum de votre appareil Iorsque

routes Jes instructions relatives _ Ja s_curJt_ et _ son

fonctionnement auront _t_ bien assimil_es et raises en

pratique de fa_:on routini&re.

Conservez ces instructions pour

vous y reporter uit_rieurement.

Exigences avant i'installation

Outiis et materiel n_cessaires & i'instaliation :

OU OU

CI6 _ CI6 polygonale Cliquet et

molette de 3/8 po ensemble

ou de 10 mm de douilles

<:L.¸-%

Pince

r6glable

Niveau de charpentier

Exigences d'lnstallation

Exigences des syst rnes lectriques

CIRCUIT = Circuit ind_pendant de 15 ampSres, polaris8 et

mis 8 ia terre, avec fusible temporis_ ou disjoncteur de

15 A.

ALIMENTATION F:LECTRIQUE - C6ble monophas_ & deux

ills mis 6 la terre, 120 volts, 60 Hz; courant alternatif.

......,E UE...................................................................................................................................................................

Etant donn_ les variations de tension possibles, I'utilisation

de cette laveuse avec une source d'alimentation produite

par une g_nSratrice 6 essence, solaire ou _olienne ou

par toute autre source d'alimentafion diff_rente de celle

fournie par les services publics n'est pas recommand_e.

PRISE = Prise 8 trois aivSoies et mise 8 ia terre situ_e 8

un endroit o0 il est possible de raccorder Jecordon

d'aJimentation de la laveuse une fois que cette derni_re

est install_e.

Prise murale avec

pas.n'enlev_

pas et ne me_ez pas hors

circuit la broche de mise

,_ la terre de cette fiche.

Cordon_lectdquemuni

avecmise_laterre

Une prise GFI (disjoncteur de fuite de terre) n'est pas

n_cessaire.

Exigences relatives b la raise b la ferre

Av ISSEM ..................................................................................................................

RISQUE DE CHOC ELECTRIQUE

Un raccordement inad6quat du conducteur de terre

de I'6quipement peut accroffre les risques de choc

6lectrique. En cas de doute quant & la raise 6 la terre de

I'appareil, consultez un _lectricien qualifi_.

1 Cet appareil DOlT 6tre mis & la terre. En cas de

mauvais fonctionnement ou de panne, la mise &

la terre diminue les risques de choc 61ectrique en

fournissant au courant 61ectrique une trajectoire de

moindre r6sistance.

2 F:tant donn6 que votre laveuse est 6quip_e d'un

cordon d'alimentation pourvu d'un conducteur de

raise & la terre et d'une fiche de raise & la terre, la

fiche DOlT 6tre raccord6e 6 une prise appropri6e

(avec conducteurs en cuivre) correctement install6e

et raise & la terre conform6ment aux codes et

r6giements iocaux ou, si aucun code local ne r6git

ce type d'instaliation, & la plus r_cente _dition du

National Electrical Code (ANSIiNFPA 70). En cas

de doute, faites appel 6 un _lectricien qualifi_. NE

COUPEZ PAS et NE MODIFIEZ PAS la broche de

raise & la terre du cordon d'alimentation. Si votre

prise murale n'est pourvue que de deux fentes,

ii incombe au propri_taire de faire appel & un

_lectricien quaJifi_ pour la rempJacer par une prise 61

trois aJv_oles et raise & la terre de fa_on adequate.

Exigences relatives b I'alimentafion en

eau

Les robinets d'eau chaude et d'eau froide DOIVENT 6tre

instali6s 6 une distance de 107 cm (42 po) ou moins de

i'arrivSe d'eau de votre iaveuse. Les robinets DOIVENT 6tre

de 1,9 cm (3/4 po) et fiietSs en fonction d'un raccordement

de tuyau de iaveuse. La pression de i'eau DOlT se situer

entre 206,8 et 827,4 kPa (30 et 120 ib/po2). La diffSrence

de pression entre i'eau chaude et I'eau froide ne dolt pas

d6passer 68,9 kPa (10 Ib/po2). Le service des eaux de

votre Iocalit8 peut vous informer sur ia pression de votre

alimentation en eau.

Exigences relatives au syst me d' va-

cuation

1 Le drain dolt pouvoir 8vacuer 64,3 L (17 gai) d'eau 6

la minute.

2 Tuyau d'_vacuation d'au moins 3,18 cm (1-1/4 po) de

diam_tre.

3 Le tuyau d'_vacuation doit _tre situ_ entre une

hauteur minimale de 61 cm (24 po) et une hauteur

maximale de 244 cm (96 po)

96"

(244cm)

max.

24"

(61cm)

min.

Le tuyau de vidange raccord6 6 la laveuse peut convenir

& un tuyau d'6vacuation de 188 cm (74 po) de hauteur.

Pour des tuyaux d'_vacuation plus hauts, utiiisez ie tuyau

portant ie num6ro de piSce 137098000, disponibie

aupr6s des centres de r6paration et de pisces Sears.

Placer un appel de service au 1-800-LE-FOYER.

Exigences d'lnstallafion

Exigences de d_gagemenf

.......IMPO NT....................................................................................................................................................

N'INSTALLEZ PAS VOTRE LAVEUSE :

1 ,_ un endroit expos_ aux _coulements d eau

ou aux al&as des conditions m_t_7orolocjiques

ext_rieures. La temperature ambiante ne devrait

jamais tomber sous 15,6 °C (60 °F) afin d optimiser

I'emcacit_ du d_tercjent.

2 lk un endroit (cjaracje ou b6timent similaire) oO de

] I'essence ou d'autres substances inflammables sont

entrepos_es (incluant des automobJJes).

3 Sur un tapis. Le plancher DOlT _tre sonde et

presenter une pente inf@ieure & 2,5 cm (1 po).

Afin d'_Tviter les vibrations et Jed_placement de

J'appareil, iJ peut _tre n_cessaire de renforcer Je

plancher.

JnstaJJationdans un Endroit en Refrait

ou une Armoire

Si la laveuse et la s_cheuse sont installSes dans le mSme

placard, une ventilation est requise dans ia porte : Une

ouverture d'au moins 774,2 cm2 (120 po2), divisSe

8cjaiement au-dessus et au-dessous de ia porte, est requise.

Les ouvertures 8 persiennes doivent 8tre situSes 8 7_6 cm

(3 po) du haut et du bas de ia porte. Les ouvertures

d'aSration ne doivent pas 8ire obstru_es Iorsqu'une

porte est instaliSe. Une porte 8 persiennes dont ies

ouvertures sur i'ensembie de ia porte sont 8quivalentes aux

recommandations peut 8tre utilisSe.

DF:GAGEMENTS MINIMAUX - Pouces (Centim_tres)

CbTI_S ARRIERE DESSUS AVANT

AIc6ve 0" (0 cm) 0" (0 cm)* 0" (0 cm) n/a

Sous le

O" (0 cm) O" (0 cm) * O" (0 cm) n/a

comptoir

Placard O" (0 cm) O" (0 cm) _ O" (0 cm) I" (2.5 cm)

0" -:::::1_0 I_--_

(Ocm) :' _!_

0" l

(0cm)

(0cm) ii

7 3"

Porte de placard

---1--

60 sq. in.

(387.1cm 2)

______

---_--

60 sq. in.

(387.1cm 2)

Dimensions de Laveuse

49.5" (126 cm)

Avec la porte

grande ouverte

Laveuse autonom_

sur le plancher

Plancher

Laveuse mont4e sur' i

le socle optionnel

Plancher

l l m

• 2Z8" (70.5 cm)

A partir de I'avant de la porte

orsqu e e est ferm6e

Raccord de

I'allmentation en

eau (] I'arri@re

de la laveuse 1

2Z0"

(68.5 cm)

36.0"

(91.5 cm)

Tuyau de vldange

6 I'arri&re de la

laveuse 3

5t.25"

(130 cm)

50.8" (129 cm)

Avec la porte

grande ouverte

Plancher

29,75" (75.5 cm)

,&,partir de I'avant de la porte

Iorsqu'elle est ferm6e

m l m

71.5"

(182 cm)

1Longueur des tuyaux d'entr&e d'eau chaude et d'eau froide de la laveuse, environ 109 cm (43 po).

2Longueur du cordon d'allmentafion de la laveuse, environ 152,5 cm (60 po).

3Longueur du tuyau de vidange de la laveuse, environ t32 cm (52 po).

4Longueur du cordon d'allmentatlon de la s&cheuse (_ gaz_ environ 152_5 cm (60 po).

Raccord de

I'alimentation

en eau (] I'arri&re

de la laveuse _

Allmentation en

gaz @I'arri@re

de I'appareil

gaz

37"

(94 cm)

2Z0" --'1_

(68.5 cm)

Alimentation

&lectrique 8_

I'arri_re de

la s6cheuse 4

Hauteur de la

llgne centrale

de I'&vent arri_re

Tuyau de

vldange

6 I'arri_re de

la laveuse 3

39"

(99 cm)

D ballage de la Laveuse

Retrait de remballage en mousse

DStruisez le carton d'emballage et les sacs en piasfique

aprSs avoir d_baii8 I'appareii. Les enfants pourraient

les utiliser pour jouer. Le carton recouvert de tapis, les

couvertures et ies feuiiies de piastique peuvent 8tre

_tanches & I'air et provoquer la suffocation. D_posez

tousles mat_riaux d'emballage dans un conteneur &

dSchets ou faites en sorte que ies enfants ne puissent y

avoir accSs.

| Retirez temporairement le ruban de la porte.

2 Ouvrez la porte de la laveuse et retJrez tout ce qui

se trouve dans le tamboun

3 Fermez la porte et posez le ruban de porte

nouveau.

4 Pour prot_ger {e piancher_ utilisez un tapis, une

couverture ou une piece de carton et couchez Ja

Javeuse sur le cote arriere.

ATTENTION...................................................................................................................................................

DANGER DE POIDS !xcESSIF

Pour eviter les biessures au dos ou d autres types de

bJessure, demandez i'aide d'autres personnes pour

5 Retirez la base en styromousse et ie bouchon

d'exp_dition; mettez-les de c6t_.

6 Remettez soicjneusement la laveuse en position

verticale.

7 D_placez soicjneusement la laveuse & moins de 1,2 m

(4 pi) de son emplacement d_finifif.

IMPORTANT .................

Conser_e_la baseenstvro_ousseetle bouchon

d'exp_dition afin d_viter d'endommager I'appareil dans